Record and not monitor

When recording how can I record, but not monitor all tracks. For instance I want to be able to hear the Guitar and bass, but not the drums while recording. I'm using Alesis IO|26 FireWire.
Thanks

The mute button did the trick. I wasn't sure if I muted an input or channel if it would still record. We had our small group together and I didn't have a lot of time to play around with it. The drums were just too loud and we didn't want to hear them while recording. The hardware monitoring is a good idea to. I haven't even looked at it yet, but when not recording I think it would be a lot easier to use that then dealing with logic.
Thanks for the help
Message was edited by: GLank

Similar Messages

How to restrict the last record and not moving to next reocrd

1) how to restrict the last record and not moving to next reocrd.
2) Also for the F6 key(for new record).

When you are on the last record, next-record will create a new one, so that my question is do you want to forbid new record creation.
Francois

Where is the sound recorder and notes on Z3?

Where is the sound recorder and notes on Z3?

I have checked a couple of units here and no preinstalled note application on them either. However there are a large number of small and free notepad type applications that can be installed via the Playstore with little effort.
- Official Sony Xperia Support Staff
If you're new to our forums make sure that you have read our Discussion guidelines.
If you want to get in touch with the local support team for your country please visit our contact page.

Agent Desktop Recording and Silent Monitoring with IP Communicator.

Reading through the forums I have seen several posts which make me think this should work, but I can't seem to get silent monitoring or recording using the agent desktop to work when the agent is connected through IP communicator. Currently I have help desk agents using extension mobility to log into 7962s that are connected to thier desktops running agent desktop connecting to UCCX 7.01. Silent monitoring and recording work fine with thier hard phones. When I install IP communicator on the PC and log into it using EM, the agent desktop takes control of the IPC just fine and will distribute calls to it, but my recordings are blank and silent monitoring from an supervisor station fails to initialize. Is there something I am missing in the configuration that is special when using IPC instead of a hard phone? Thanks in advance.

Couple of things I've learned about the CIPC and monitoring/recording:
No named devices. Use the SEP + Mac Address of the local Ethernet interface.
Ensure the Ethernet interface can be put into permiscuous mode.
Ensure you are NOT using a shared line appearance for the IPCC Extension.
If you are using CAD to do the monitoring/recording, launch the CIPC before you launch CAD
If you are using SPAN, ensure the CIPC RTP traffic will traverse the network where the SPAN interface is located.
If you are calling phone-to-phone, know that the CIPC will attempt to negoitiate G.722. UCCX cannot monitor/record G.722. Set the region or call to the PSTN where you can guarantee a G.711 or G.729 call.

How to make the price in PO to adopt from info-record and not changeable?

Hi Xperts,
Can somebody explain to me how to set the PO price to be adopted from the info-record and is NOT CHANGEABLE at the creation and change of PO screen. I know that i can configure the field selection for the PO type to be "price as display" only. Any other solution?
Thanks.

Hi!
tick the check box info-update at the item detail under master data tab in a PO.
its significance is as follows:-
Info record update
    Determines whether the prices and conditions of this purchase order item
    are suggested in future PO items.
Use
    Selecting InfoUpdate causes one of the following situations to occur:
        -   If just one info record (with or without plant) exists, it is
            updated.
        -   If no info record exists and "plant condition requirement" was
            specified in Customizing, an info record with plant is created.
            Otherwise, an info record without plant is created.
        -   If two info records exist (that is, one info record with plant
            and one without plant) the info record with plant is updated.
Dependencies
     You can specify that prices and conditions in purchasing info records
     are only allowed at plant level in the Purchasing IMG, under Conditions
     -> Define Condition Control at Plant Level.
Hope this helps you,
Regards,
Archit.

How do you record video with usb mic and have the audio from garageband be the sound when recording and not just your normal voice but garage band effects for youtube?

How do you record video with usb mic and have the audio form garageband be apart of the video when recording, meaning the audio from garageband and echo and not just your normal voice for youtube post?its not add the garageband audio its just normal voice from mic no effects is going thru?

Hi Life93,
What you describe would be possible by recording your video, then removing the audio from it and adding audio from GarageBand once the video is in iMovie (I presume here that you are using iMovie for your video production. Other applications may need different methods.)
See this thread on how to remove the audio from a clip in iMovie -
Is there a way to separate audio from a video c...
https://discussions.apple.com/thread/1779767
To add audio from GarageBand use this article -
iMovie '11: Add a sound clip to your project
http://support.apple.com/kb/PH2255
Thanks for using Apple Support Communities.
Best,
Brett L

Lost mail, forwarded doc with attachment. No record and not received

Using a message and attachment from an email in my files, created new message with updated info to send to CEO. Hit 'send' and heard normal rush sound. Later checked my sent file and no record. Called CEO exec asst not received. Tried again with a shorter message same result. Sent another message with an attachment to another exec, no problems. iPad problem or system?

Not recipient.
I have both a Me and a Yahoo account.
When I forward a mail with an attachment using Yahoo account, it shows the sending bar, makes the sound that a mail was sent and even put the arrow icon on the left side of the original mail. But no mail is sent (recipient doesn't receive it and I don't get my blind copy).
This also happens when I send a mail from an app (notes, noterize, numbers, pages, etc.).
If in both cases I use my Me account, it works fine.
Using Yahoo account, forward without attachments, and reply works fine.
Don't know what to do.
iPad iPhone OS 3.1.3

Recording and Notes in AppleScript

Dear AppleScript Forum Users,
Is it possible to record something in AppleScript and then play it back? Is it possible to change the notes in the say command. What I mean is it possible to change the pitch of what the computer is saying? Eg. say "Hi, I am new here." where Hi is a hogher pitch than the rest.
Thanks,
JamesBond

There are several parameters that can be used with the say command, including saving the output to a file - see the StandardAdditions dictionary. In addition, embedded speech commands can be used, for example:
say "[[pbas +30]]Hi[[rset 0]]. I am new here."

Scale maintained in info records but not picking up in scheduling agreement

Hi,
We have maintained scales for PB00 in info record (subcontracting), this scale is picked up in Subcontracting Purchase Order.
But when we are trying to create Subcontracting scheduling agreement, this scale is not picked up by the system.
Why the system is picking up scales for PO but not for scheduling agrmment?
Regards,

Hey there,
Please check your InfoUpdate Indicator on the scheduling agreement.
The indicator determines which prices and conditions are suggested in future PO items.
Prices and conditions can apply to an entire purchasing organization or to a single plant within a purchasing organization.
For example, if you create a purchase order for a plant for which an info record has been defined at plant level, the purchase order is based on the conditions in the plant info record and not on the conditions that apply to the purchasing organization.
probably your info record is at the Porg level and not at the plant level and hence it's not picking it up.
Hope this helps,
Cheers,
Dhaval

After using apogee duet, mac's built in mic & logic's track headers for recording are not working properly. How do I fix it?

I use logic 9
After using apogee duet for mac, I was away from my home studio without the duet and wanted to record vocals via the internal microphone on my mac book pro. (Obviously, I know it wouldn’t be the same quality. I wanted to do it as a draft, because I had a melody in my head and wanted to record it so I could remember it later.)
After opening up a project I was unable to record audio. I noticed the track headers had changed. Sometimes the “record ready” button was missing. But whether it was there or wasn’t, the same thing kept happening… After pressing the “record button” or the “record ready” button a window would pop up that said, “No input source selected!” I tried to trouble shoot by configuring track header and by going to prefereces>audio>devices>core audio, and switched the “input device” to “built in microphone,” and things like that, but I still would get the same pop up window indicating “no input source selected.” To be thorough, in preferences under “core audio,” I have selected universal track mode, 24 bit recording, and software monitoring.
Do I need to reset something?
If your recommendations help fix the immediate issue temporarily, how do I keep it from reverting back to the same problem if I feel like switching between the duet interface and the built in mic in the future? How do I keep it permanently from this malfunction? It seems like this is something simple that would be addressed.
Also, as I was trying to think of anything it could possibly be. I wonder if it could be the driver I installed for an old m-box2 possibly causing an issue. After getting my new mac book pro, I downloaded a driver for m-box2 (the second generation that came out in 2005 and used pro tools LE.) I used the m-box on my previous computer and it worked well. Since I purchased a new macbook, I tried to use it on my new computer, but since the m-box2 is a 32 bit system, it didn’t work very well, which is why I got the duet. I don’t know if that could possibly be messing anything up. If so, should I uninstall it somehow?
Thanks

Ok, think this through... you've changed from a stereo source to a mono source.
The message reads: “No input source selected!”
On the track you're trying to record there is an Input section directly underneath the I/O label. Click and hold to select the correct Input for that track.
Also, the project you opened was saved with the Duet's driver/interface parameters.. if you open the same project without the audio interface Logic will do it's best to pick I/O that's compatible but I've never seen any DAW do this perfectly.. it always takes a small amount of user input. Especially since you've changed from the Apogee to the internal mic.

Records are not updating.

Hi,
Some of our newly created records and not updating during the full refresh of database. Can someone suggest the something on this?
Thanks in Advance!!!
PG

DSO is nothing but overwright and addtion option , so i think again excute DTP
or
similer data is there or not check it,because some times simeler data available at that time it happen.
Regards,
BAbu
Edited by: maheshbabu157 on Jul 9, 2011 5:37 PM
Edited by: maheshbabu157 on Jul 9, 2011 5:37 PM

Delete only the child object and not the parent object

Hi,
I have the below code:-
TAnswer
@ManyToOne(fetch = FetchType.LAZY)
     @JoinColumn(name = "question_id", nullable = false)
//     @Cascade(value=CascadeType.ALL)
     public TQuestion getTQuestion() {
          return this.TQuestion;
     }     TQuestion
@OneToMany(fetch = FetchType.LAZY, mappedBy = "TQuestion", orphanRemoval = true)
     @Cascade(value=CascadeType.ALL)
     /*@Cascade({org.hibernate.annotations.CascadeType.SAVE_UPDATE,
            org.hibernate.annotations.CascadeType.DELETE,
            org.hibernate.annotations.CascadeType.MERGE,
            org.hibernate.annotations.CascadeType.PERSIST,
            org.hibernate.annotations.CascadeType.DELETE_ORPHAN})*/
     public List<TAnswer> getTAnswers() {
          return this.TAnswers;
               In Java:-
     public void removeAnswers(TQuestion question)
                    throws ApplicationException {
               List<TAnswer> answerList = question.getTAnswers();
               deleteall(answerList);
     public void deleteall(Collection objects) {
               try {
                    getHibernateTemplate().deleteAll(objects);
                    getHibernateTemplate().flush();
               } catch (Exception e) {
                    throw new ServerSystemException(ErrorConstants.DATA_LAYER_ERR, e);
     }               Here the "deleteall" will delete both the answer records and question records, I don't want the questions
     records to be deleted. I have tried making the question as null when we set the answer object to be passed for delete
     bit still it is     deleting the question records as well.How to achieve the above in deleting only the answer (child) records
     and not the question(parent) record? Is there any thing we need to do with @Cascade for Question object? Please clarify.
Thanks.

What does deleteAll do, it doesn't look like a JPA method. You might want to ask your question on your provider forum, or use straight JPA methods as a simple EntityManager.remove(answer) on each answer in the collection should work.
Regards,
Chris

Interaction Record History & Notes History

Hi All -
I have a question regarding the Interaction Record history & Notes History assignment blocks in the IR Work Center Page.
The IR Work Center page has an assigment block to list the recent interaction records and notes history. However, this component lists only the last few interaction records and their corresponding notes history. (Like the last 4).
Is it possible to increase this number through configuration? Or does it need to be an enhancement to the notes history and interaction history components?
Regards,

Hi Nikhil,
Yes, it is possible to increase the number of interaction records that are being displayed.
The code that is limiting the number of interaction records to 4 is present in the Custom Controller ICCMP_BT_IRHIST/CuCoIRHist. The code is present in the method GET_LAST_INTERACTIONS of the implementation class of the custom controller.
The below code results in only a few Interaction Records based on the confirmed partner;
TRY.
      CREATE OBJECT lr_query_service.
    CATCH cx_crm_unsupported_object.
      me->typed_context->btordercusthist->clear_collection( ).
      RETURN.
ENDTRY.
lr_query_service->set_query_parameters( it_parameters = lt_parameter ).
lr_queryres_col = lr_query_service->get_query_result( ).
If all the Interaction Records are to be fetched from the database, then the search query 'BTQuery1O' needs to be executed. The parameters for partner number and object_type are to be passed.
Once, result query is obtained, the same collection can be set to the context node BTORDERCUSTHIST of this custom controller.
Finally, the code to limit the number of Interaction records to 4 which is given below needs to be commented;
* restrict to 4 result entities
lr_bo = lr_queryres_col->find( iv_index = 5 ).
WHILE lr_bo IS BOUND.
   lr_queryres_col->remove( iv_bo = lr_bo ).
   lr_bo = lr_queryres_col->find( iv_index = 5 ).
ENDWHILE.
Regards,
Jekin

Help: Using Record and Collection Methods

I have created a record and I have to loop for as many records in the "RECORD". However if I attempt using any of the Collection Methods, I get the following error:
ERROR at line 1:
ORA-06550: line 41, column 14:
PLS-00302: component 'EXISTS' must be declared
ORA-06550: line 41, column 4:
PL/SQL: Statement ignored
ORA-06550: line 47, column 26:
PLS-00302: component 'COUNT' must be declared
ORA-06550: line 47, column 7:
PL/SQL: Statement ignored
Here is the SQL I am trying to execute:
DECLARE
TYPE Emp_Rec is RECORD (
Emp_Id Emp.Emp_no%TYPE
, Name Emp.Ename%TYPE
ERec Emp_Rec;
Cursor C_Emp IS
SELECT
Emp_No, Ename
From Emp;
begin
OPEN C_Emp;
LOOP
FETCH C_Emp INTO Erec;
EXIT WHEN C_Emp%NOTFOUND;
END LOOP;
IF Erec.Exists(1) THEN
dbms_output.Put_line('exists' );
else
dbms_output.Put_line('does not exists');
end if;
CLOSE C_Emp;
FOR I IN 1..ERec.COUNT
LOOP
dbms_Output.Put_Line( 'Row: ' || To_Char(I) || '; Emp: ' || ERec(i).Name) ;
END LOOP;
end;
Can anyone help, please?
Thanking you in advance,

You only defined a Record and not a collection, therefore you cannot use .EXISTS
This is how you would use record, collection and exists together
DECLARE
TYPE Emp_Rec is RECORD
         (Emp_Id Emp.Empno%TYPE,
          EName Emp.Ename%TYPE );
TYPE Emp_tab is table of emp_rec index by binary_integer;
ERec Emp_tab;
Idx INTEGER;
Cursor C_Emp IS
     SELECT EmpNo, Ename    From Emp;
begin
IDX := 1;
OPEN C_Emp;
LOOP
       FETCH C_Emp INTO Erec(IDX);
                 EXIT WHEN C_Emp%NOTFOUND;
       IDX := IDX + 1;
END LOOP;
IF Erec.Exists(1) THEN
       dbms_output.Put_line('exists' );
else
       dbms_output.Put_line('does not exists');
end if;
CLOSE C_Emp;
FOR I IN 1..ERec.COUNT LOOP
        dbms_Output.Put_Line( 'Row: ' || To_Char(I) || '; Emp: ' || ERec(i).eName) ;
END LOOP;
end;I hope you realize that this is only an example of how to use RECORD, COLLECTIONS and Collection Methods (.EXISTS, .COUNT)
and not the best way to display the contents of a table.

Monitoring and recording feature not working in UCCX

Hi,
The recording and monitoring option is not working in the new UCCX setup I have installed.I have configured following things for desktop monitoring as per the document
1)Checked that IP Phones are diasy chained and speakers of Supervisor's PC is working,NIC card of agent's and supervisor desktops are compatible
2)In web CDA P phones to be monitored have been configured
3)In CCM configured the phone for "Span to PC port" as enabled also configured "Advertise G.722 codec" as disabled
4)Ran postinstall.exe on agents system and checked if correct NIC adapter is being used for monitoring
5)Checked the NIC binding order in UCCX server and that is correct
I noticed one thing that "services" in both CAD and CSD are showing as "partial services" and they are monitoring and recording services only.Hence is this problem related to these services? How do i correct the recording and monitoring issue?
Regards
Amit

/* Style Definitions */
table.MsoNormalTable
{mso-style-name:"Table Normal";
mso-tstyle-rowband-size:0;
mso-tstyle-colband-size:0;
mso-style-noshow:yes;
mso-style-priority:99;
mso-style-qformat:yes;
mso-style-parent:"";
mso-padding-alt:0in 5.4pt 0in 5.4pt;
mso-para-margin-top:0in;
mso-para-margin-right:0in;
mso-para-margin-bottom:10.0pt;
mso-para-margin-left:0in;
line-height:115%;
mso-pagination:widow-orphan;
font-size:11.0pt;
font-family:"Calibri","sans-serif";
mso-ascii-font-family:Calibri;
mso-ascii-theme-font:minor-latin;
mso-fareast-font-family:"Times New Roman";
mso-fareast-theme-font:minor-fareast;
mso-hansi-font-family:Calibri;
mso-hansi-theme-font:minor-latin;}
I would first recycle the VOIP Monitoring Service on both node if this is HA. This will not affect calls or call processing.
In addition, you stated you ran post install on the clients desktop but have you ran post install on the server itself?
In the desktop Administrator, what server is selected to be the default VOIP Monitor server?
Jason M. Hutchinson

Record and not monitor

Similar Messages

Maybe you are looking for