Recovery Disk wont work for new Hard drive.

I have a HP Pavilion dv5-2132dx with windows 7 64-bit. Recently a message started popping up warning that the hard drive might fail and I need to back up my data. I decided to buy a new hard drive. The hard drive a bought is 320GB SATA 7200RPM by western digital. It is the same brand and model as the hard drive currently in the computer. I popped in the new hard drive and inserted the recovery disks I bought from HP. The computer goes through the whole process of istalling the disks. However, on the final setup it shows the welcome screen. Then u hear a beep and then the screen goes black with a message saying that windows could not install and to try installing it again. I have done this 3 times and its always the same thing. Is this a Hard drive issue or a software issue and how can i get this to work?

Hi,
Before trying the following, make sure you can still read the 25 Character Product Activation key on your Windows COA label ( 5 blocks of 5 alpha/numeric sets ).
Assuming that this is just a problem with the Recovery process, there is a straight forward work around.
Create a retail Windows 7 installation disc yourself using another PC - just download the correct Disc Image from the link below ( this must be the exact version your notebook came with ) and use an application such as ImgBurn to burn the ISO correctly to a blank DVD - a guide on using ImgBurn to write an ISO to a disc is Here. These Images are clean and from a well-respected source, however there are only limited versions available.
Windows-7 sp1-iso-official-32-bit-and-64-bit
Use the disc to perform the installation, enter the Windows activation key found on the COA Label when requested and when the installation has completed, use the 'Phone Method' detailed in the link below to activate the OS - this method supported by Microsoft and is popular with people who just want a clean installation of Windows 7 without the additional software load normally bundled with OEM installations.
http://www.kodyaz.com/articles/how-to-activate-windows-7-by-phone.aspx
Any additional drivers you may need can be found Here.
Regards,
DP-K
****Click the White thumb to say thanks****
****Please mark Accept As Solution if it solves your problem****
****I don't work for HP****
Microsoft MVP - Windows Experience

Similar Messages

Recovery disk failure on a new hard drive?

Hello all,
Since my brother's computer got old and it is time to replace the hard drive to a sold state. So, I created recovery disks and started recovery on the new hard drive. But, the recovery progress stops at 55% for an hour and then it gives an error code "0xe0ef000e" and stops installation. I tried two more times and still the same thing happened.
So I called the customer support, and the representative is saying that my recovery disks wouldn't work with my new hard drive. Is this really true?

Hi bong8,
According to the list of error codes, 0xe0ef000e translates to "Copying file/directory failed":
http://h20565.www2.hp.com/hpsc/doc/public/display?calledBy=&docId=emr_na-c02018679-2&docLocale=
This can happen for a variety of reasons; it's not always clear why. It's possible the burning software you used introduced the error; cheap DVDs are also prone to burning issues. You could try re-burning the recovery disks at a lower speed from the old drive.
Do you have the original operating system DVD the system shipped with? You could use that to reinstall Windows. If not, you can order a recovery kit for your system here:
Ordering a recovery kit from HP in the United States and Canada
http://h10025.www1.hp.com/ewfrf/wc/document?docname=bph07143&cc=us&dlc=en&lc=en
I hope this helps

Recovery did not work with new hard drive

The original Toshiba HD(250G, sata1) of my laptop( ) crashed.
I bought new one (320G, sata 2, Western digit )
The problem is that, when I tried to use the recovery CD that I used to use it with old HD before, it did not work with this new HD well!?
After cd1 and cd2 finish installing it ask to take it out then restart, I do so, but when it comes to setup setting of windows.
An error message come out says " Windows Setup could not configure Windows on this computer’s hardware”
It restart and says again " Windows could not complete the installation. To install Windows on theis compuiter, restart the installation."
I have been trying to solve this a lot, but no way
I tried what in this link, but it drive me with another problem http://answers.microsoft.com/en-us/windows/forum/windows_7-windows_install/windows-could-not-complet...
I hope that I get the right thing to do, from ur forum by this post.
Thanks a lot

Did you folks search here for "advanced format drive"? People have had numerous weird problems with the new advanced format hard drives in older Toshibas. I can't look up all the threads for you. But here is one:
http://forums.toshiba.com/t5/System-Recovery-and-Recovery/Recovery-won-t-work-on-new-upgraded-hardri...

Why does installation cd not work for new hard drive for 2009 MacBook pro?

my hard drive died in my 2009 MacBook pro so I bought a 1tb ssd drive and had the store physically install the drive only. I arrived home and stuck in the original installation disc and pressed and held the c key after the chime. Nothing happened. after a minute or so the screen turned black and rebooted up again with the chime. It would continue to reboot whether I pressed the c key or not. when i pressed the d key it would say:
"Apple hardware test does not support this machine"
why why isn't this working like it is supposed to?
thsnks

Ryan,
Have you tried using the Startup Manager (holding down the option key) whilst booting? If everything works as it should, you should be given the option to choose the DVD to boot. Holding down the 'D' key should load the Apple Hardware Test.
Good luck,
Clinton
MacBook Pro (15” Late 2011), OS X 10.??, 16GB Crucial RAM, 960GB M500 Crucial SSD, 27” Apple Thunderbolt Display

HT1727 i copied itune music from old hard drive to memory disk the copied onto new hard drive into itunes and music wont play unless removalbe disk is inserted

i copied itune music from old hard drive to memory disk the copied onto new hard drive into itunes and music wont play unless removalbe disk is inserted

Then your iTunes must be looking at the removable disc, not your hard drive. Did you actually copy the songs onto your computer, or simply tell iTunes to look at the removable drive?
Highlight a song and click on File/Get Info/Summary>Where and check the location that iTunes has listed for the song. What does it say?

Will recovery disks work on new hard drive

I just installed new hard drive on hp laptop with Windows 7 64 bit. I used the iso file installation disc. Now I would like to use the recovery disks I made 2.5 years ago to load the original software and drivers as when the pc was new. When I put Disc 1 in the drive the pc does nothing. I've been reading online that you have to change the order of the drives in the BIOS so the pc will boot from the dvd drive.
Then further research online, I read that recovery disks will not work on a new hard drive, and on a smaller drive than was previously installed.
I did do a full system backup from old hard drive, so I have those 3 discs. I have not tried that. Basically all I use pc for is web browsing,email and an occassional movie.
I guess I just want it to seem like a new pc with all the original software and drivers.
I downloaded hp support assistant, however it states that new updates are not needed. That can't be right.
I went to hp download page, but not sure which drivers/software to download.
This is wearing me out. Please help if you have any suggestions/advice. Thank you!

Paul, thank you for answering. I have a HP Pavilion DV7-4270us.
From my research, I don't believe the operating system is on the recovery disks. I am very hesitant to work with the recovery disks again. Anyway my new hard drive is 500 GB which is smaller than the old 640 GB that was previously installed from the factory. So the recovery disks may not work on a smaller drive.
At this point, I would like to get back HP Media Smart and Synaptics click pad working. I have downloaded the driver for the clickpad, but it does not operate like it used to. No settings to choose from etc. I downloaded the Media Smart Software package and driver, but the software package is not there. I was just reading online, and found a link for the Simple Pass Identity Protection fingerprint reader. I downloaded it, and seems so far to work. Also, on the keyboard the light on the keyboard button for (volume on and off) remains lit all the time. It used to light up only when the volume was off.
Man, you sure can run into all kinds of problems when you install a new hard drive. Any suggestions will be greatly appreciated!! Thanks, Ken.

Recovery discs do not work with new hard drive

Hi I have come here desperately seeking help as I am not too knowledgeable with the workings of computers and I have spent an incredible amount of time just trying to get my laptop to some level of functionality. I purchased a HP Envy and it had a corrupt hard drive which would not work from day one, laptop was new. After a year of constant pressure on HP they finally decided to replace it and let me choose any laptop so I went with the Beats Envy 14 as it was the best one offered from the selection. Low and behold the thing would not work properly from day one, again my brother who is much more of an expert said that there was definitely a hard drive issue so for the past 3 years I have put up with a computer that constantly crashes with BSOD, where I have lost data on numerous occasions (only so often I can back up), that I have had to constantly reset the thing using HP recovery discs, and that generally cannot cope when performing multiple tasks. HP are most certainly shocking builds from my experience. Then just last week the hard drive just craps itself and the laptop no longer will boot up. I took it to a guy to get it at leYst working again so he has installed a new hard drive but with an old version of Windows 7. I want to go back to the Windows version I was akin to on the HP recovery disk , and essentially have it all set up as before except for now having a workable hard drive however I get the message: "This computer is not supported by the System Recovery Discs.You will not be able to continue to recover this system with these discs.Error: 0100 - 3385 - 3078" I also tried out of interest to load my old Windows 7 disc I had and XP but had no success. Tried booting from startup etc and various things suggested on help forums. Please tell me I am not stuck with this version of windows. Whilst the discs included Windows 7 it was a totally different version, this home premium one is terrible. Any help/advice would be gratefully received. Thanks

no they were both 500gb. I read about that already, I heard about creating a partition for recovery etc but this is all a bit above me , as I said I am not very technical when it comes to the working of a computer. These discs worked perfectly before but now with the new hard drive will not load at all. I essentially hate the Windows Home Premium verions the guy who fixed it put on, whilst the discs had Windows 7 on them the icons were way smaller, the desktop neater, the buttons different, everything was a lot more modern and I was used to it. This version looks like something from the 90s, have to constantly adjust size of Mozilla when browsing as it is huge. I have my own version of Windows 7 on another disc but the hard drive will not let it load either........considering waiting for Windows 10 but again unsure if this new hard drive will even let that update Thanks

Using the disk to disk recovery tool to image a new hard drive

I have a new SSD hard drive that I am installing and want a fresh version on Win 7. I plan on using my existing hard drive just for data and to maintin the recovery partion in case I need it again. I want to do a disk to disk recovery. I get to the point in the Recovery 4.3 software where it prompts me to confirm I will loose all my data on the partition, but I do not see where it allows me to choose the new hard drive. I do not want to loose my data so I exited out. Did I not go far enough into the processs to allow me to choose the hard drive? I have not found a manual for the recovery tool to show me what's next. I have the new hard drive installed in the ultrabay.
T410i
Thanks,

Check on your HDD win 7 RNR if you have the Create Product Recovery option. This will back up the Recovery Partition. First disc is bootable recovery, you can use a CD. Second disc is data, try a DVD for this. It may create a 3rd disc.
When you get done, you want a recovery partition on the SDD. The recovery bootable and partition are fairly small.
Thus, when you use these disc to populate the SDD, you have a recovery partition on the SDD.
When I ordered my PC, I ordered 2 HDD's 120GB and 320GB. Windows does not let you select where the operating system goes to. It uses the first HDD it finds (which might be your win 7 Hdd!!). In my case, it came from the factory with (vista) on the 320GB. I had to swap them, similar to what you are doing. I used the Product Recovery disk set AND had to disconnect the 320GB for the recovery to go to the 120GB.
What size is your HDD and SDD? I would take backups of your Win 7 system. Last thing you want is a messed up win 7 HDD. If all works, you will have a bootable HDD and SDD and might have to decide which one to use every time you boot up.
Down the road, when SSD is as you like it, copy the HDD data over to the SDD. Erase the HDD, then copy the HDD data back over. Thus HDD is truly a second hard drive(data drive).
Side note: The placement of the New win 7 is dependent on the Logic of the Recovery partition. I would guess where ever the Q drive is created, that is where the operating system is going to go. Could be Win7 install (standalone win 7 install DVD) logic Now allows you to choose Hard drive 1 or Hard drive 2,

Disk Utility in Internet Recovery mode cannot properly detect new hard drive

I intend to format my new hard rive and install OS X into it.
Here is my problem, I bought a new 1TB HGST 7200rpm hard disk and put into the macbook. I boot up under Internet recovery mode, under the disk utility I tried format to MacOS Extended Journaled but it takes ages (stuck for more than 15 minutes). I simply just cannot get the macbook to read the drive under disk utility from Internet recovery mode.
Here are the things that I have tried:
1. Boot the MacBook from old drive, successfully use the disk utility to zero out format (MacOS Extended Journaled) with 1 partition (GUID). But when I boot the Mac under Internet recovery mode, the disk utility simply cannot mount the drive.
2. Restore the new drive (as an external drive) from the old drive using disk utility, successfully restore. I could startup the new disk as an external drive, but when I put it into the Mac it shows flashing folder. I waited for more than 30 minutes, the flashing folder just stays there.
3. Boot the MacBook on Internet recovery mode and connect the new drive as external drive, no problem. I reinstall OS X into it but it midway it stop and error message says something like cannot add additional components.
Not sure what is the problem, I think I have exhausted all method. There is no issue with the new hard drive and MacBook.

The MacBook is early 2013. It came with 1TB Mountain Lion, I left the DVD in my country so I don't have it with me. How do I download the installer? the Mac App Store only lets me upgrade the OS to Maverick.
I have tried to restore the new drive from my old drive, but the only way is to use Internet Recovery. The Disk Utility boot from the old drive OS (Mountain Lion) does not allow me to restore my new hard drive from the old (current boot) drive, the message instruct me to use the Internet recovery mode. From here I can see my new drive format as GUID, but when I boot to Internet Recovery the Disk Utility recognised my new drive format as Master Boot Record instead of GUID...?????

Need Win 7 recovery discs for new hard drive

I am not sure which Windows 7 Operating system my laptop had, but I need the recovery discs to put Windows 7 back on my HP dv6-6167cl notebook.
My original issue was that my notebook was unable to restore or anything on its own. After calling HP support and performing a guided diagnostics test, it was determined that my hard drive was bad. I purchased a new hard drive and replaced it, but need to get Windows 7 back on it.
Thanks!
This question was solved.
View Solution.

Hi,
Your notebook originally shipped with Windows 7 Home Premium 64bit - you can order a replacement set of Recovery Media from the link on your Product Page below.
http://h10025.www1.hp.com/ewfrf/wc/softwareCategory?os=4063&lc=en&cc=us&dlc=en&sw_lang=&product=5118...
Regards,
DP-K
****Click the White thumb to say thanks****
****Please mark Accept As Solution if it solves your problem****
****I don't work for HP****
Microsoft MVP - Windows Experience

How can i restore from Recovery Disk if my notebook's hard drive and dvd drives are dead.

Hi. Good day. My hard drive just crashed and im trying to restore from my restore disks. Unfortunately, my dvd is dead too. I copied the recovery disks to a new hard drive and tried booting from a flash drive but the noteebook is still giving me the SMART hd error message. Please help. Thanks.

Hi,
If you have, or can borrow an external CD/DVD drive it would be worth trying this although I'm not certain your notebook will support booting from a drive connected via USB.
Another option may be to see if you can find a second hand optical drive on somewhere like Ebay - the drives compatible with your notebook can be found on Page 59 of your Maintenance & Service Guide. It may even be worth removing a re-seating your existing drive just in case this helps as described in this section.
Does the drive show up in Device Manager? If it does, right click it and select Properties. Select the driver tab and see if there is an error code in the status box.
Regards,
DP-K
****Click the White thumb to say thanks****
****Please mark Accept As Solution if it solves your problem****
****I don't work for HP****
Microsoft MVP - Windows Experience

Process for new hard drive

Hi everyone,
I was hoping somebody could point me to some tutorials for upgrading the hard drive in my PowerBook G4 (1Ghz).
I own an external drive (usb only) that is the same size as the drive in my PB (80gb), this is what I'd use to back up my hard drive (I could borrow a larger drive from work if necessary).
What is the best process for backing up? Should I use Carbon Copy? I already have Retrospect Express.
How can I make sure that I won't need to reinstall all my 3rd party apps (ex; iLife, Photoshop)? Would all of this be ported over when I copy my old hard drive over to the new hard drive?
What is the best process for copying the backed up/copied hard drive to the new hard drive? Won't I need to reinstall Tiger first? Then run updates?
Thanks for the help!

"What is the best process for backing up? Should I use Carbon Copy? I already have Retrospect Express."
I just replaced my drive, I used SuperDuper, it worked flawlessly, a major first for me since using OS X. I swear I'm not from that company, but it made a perfect bootable disk, important since I was swapping drives directly after copying data via USB to external enclosure. Had drive duplication problems prior, carbon copy was a no-go for me, to complicated, something not right w/ the updates, i forget what, it has been a while, just remember I was forced to reinstall apps.
Should have gotten a firewire enclosure, could have tested it first w/ target mode, oh well.

HP Recovery Manager won't recognize new hard drive

Hello,
I have a HP Pavilion TouchSmart 14-b173cl Sleekbook. I purchased a new hard drive and I have ordered a usb recovery kit from HP.
Howevery, when I try to run the recovery manager, it gives the message no hdd.
Also, if I try and do a hard drive check, it says not installed. It does not detect the hdd. However, if I put back the original hdd and run the recovery manager, it does recognized it and allows to start the recovery process.
Can anyone help me with this issue? Why does the laptop does not recognize the new hard drive?
Thanks!!!

Hi there
So nothing of my suggestions really did bring any improvement for you I suppose: (
These are the last suggestions I have -
Update BIOS and chipset from your product download site & try putting new HDD again.
Bios:
Updating BIOS:
http://h10025.www1.hp.com/ewfrf/wc/document?cc=us&lc=en&docname=c00042629
Latest version (Windows 8, Intel processor):
http://h10025.www1.hp.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-135598-1&cc=us&dlc=en&lc=en...
Intel chipset:
http://h10025.www1.hp.com/ewfrf/wc/softwareDownloadIndex?softwareitem=ob-112630-1&cc=us&dlc=en&lc=en...
Regards
Visruth
++Please click KUDOS / White thumb to say thanks
++Please click ACCEPT AS SOLUTION to help others, find this solution faster
**I'm a Volunteer, I do not work for HP**

System restore on DV6 not working after new hard drive installed (Vista 32-bit)

Hi there,
I have a HP Pavilion Entertainment laptop (DV6 1210sa) and recently on start up I have been receiving a message saying that the hard drive is at imminent risk of failure. I therefore burned the restore CDs and bought a new hard drive: (A Toshiba 2.5 inch 80gb SATA hard drive 5400 RPM). The first part of the restore completes successfully then the HP screen appears after a restart and then goes to install windows, but before this begins I receive a message saying “Windows setup could not configure windows to run on this computer.” I then have to restart and get the same message. Is this drive somehow incompatible? Is there something I’m missing?
Thanks in advance

Here are the factory specs for your HP Pavilion dv6-1210sa Entertainment Notebook Computer. Based on the specs, the original hard drive was 250GB. This could be a factor in your issue. It could also be that the drive is an advanced format (AF) drive. Please provide the model of the drive for our review.
Please send KUDOs
Frank
{------------ Please click the "White Kudos" Thumbs Up to say THANKS for helping.
Please click the "Accept As Solution" on my post, if my assistance has solved your issue. ------------V
This is a user supported forum. I am a volunteer and I don't work for HP.
HP 15t-j100 (on loan from HP)
HP 13 Split x2 (on loan from HP)
HP Slate8 Pro (on loan from HP)
HP a1632x - Windows 7, 4GB RAM, AMD Radeon HD 6450
HP p6130y - Windows 7, 8GB RAM, AMD Radeon HD 6450
HP p6320y - Windows 7, 8GB RAM, NVIDIA GT 240
HP p7-1026 - Windows 7, 6GB RAM, AMD Radeon HD 6450
HP p6787c - Windows 7, 8GB RAM, NVIDIA GT 240

Screen not working after new hard drive installed

Hi,
Can anyone help me, I just replaced my hard drive on my 15" G4 Aluminum Power Book as it had crashed and died on me. When I finished installing the new hard drive, when switching it on the screen remains blank. Does anyone have any Ideas why and how to get it working again. The screen was working before the hard drive crash. Any help will be much appreciated.
Thanks
Robby

Here are the factory specs for your HP Pavilion dv6-1210sa Entertainment Notebook Computer. Based on the specs, the original hard drive was 250GB. This could be a factor in your issue. It could also be that the drive is an advanced format (AF) drive. Please provide the model of the drive for our review.
Please send KUDOs
Frank
{------------ Please click the "White Kudos" Thumbs Up to say THANKS for helping.
Please click the "Accept As Solution" on my post, if my assistance has solved your issue. ------------V
This is a user supported forum. I am a volunteer and I don't work for HP.
HP 15t-j100 (on loan from HP)
HP 13 Split x2 (on loan from HP)
HP Slate8 Pro (on loan from HP)
HP a1632x - Windows 7, 4GB RAM, AMD Radeon HD 6450
HP p6130y - Windows 7, 8GB RAM, AMD Radeon HD 6450
HP p6320y - Windows 7, 8GB RAM, NVIDIA GT 240
HP p7-1026 - Windows 7, 6GB RAM, AMD Radeon HD 6450
HP p6787c - Windows 7, 8GB RAM, NVIDIA GT 240

Recovery Disk wont work for new Hard drive.

Similar Messages

Maybe you are looking for