Recovery image. Topology 3602i thru 2504 controller from TFTP Server

Hi everyone! Here is my topology and I need to perform image recovery for my 3602.
3602 can be connected and powered only by 2504 controller.
How I need to configure controller to allow communication from 3602 and TFTP server???
Does all ports on controller L3 and I need to make Routing thru 2921 Router?
Or no needs to configure  IP ports interfaces on controller and it will work on L2.
Please give me direction to follow and recover IMAGE.

Alright! Image finally loaded!  
I think it was very helpfull: Step 3 Set the timeout value on the TFTP server to 30 seconds
But image failed to boot.
But image failed to boot.

Similar Messages

  • Xmodem I/O error when copy IOS from tftp server

    After I formatted the flash I am trying to copy the IOS from tftp server using "copy xmodem: flash:c3550-ipbasek9-mz.122-44.SE6.bin" command, in rommon mode. I am getting the I/O error message.
    I did try to boot from tftp using the "set BOOT tftp:c3550-ipbasek9-mz.122-44.SE6.bin" command and then "boot" command and I get an "error loading tftp:" and  "permission denied" message.
    The tftp server is active; I did copy the old IOS before.
    Here is the output from my switch:
    switch: flash_init
    Initializing flash...
    flashfs[0]: 2 files, 1 directories
    flashfs[0]: 0 orphaned files, 0 orphaned directories
    flashfs[0]: Total bytes: 15998976
    flashfs[0]: Bytes used: 2048
    flashfs[0]: Bytes available: 15996928
    flashfs[0]: flashfs fsck took 12 seconds.
    ...done Initializing Flash.
    Boot Sector Filesystem <bs:> installed, fsid: 3
    switch: dir flash:
    Directory of flash:/
    2     -rwx      22            <date>           env_vars
    3     -rwx      43            <date>           system_env_vars
    15996928 bytes available <2048 bytes used>
    switch: set
    BAUD=115200
    BOOT=tftp:c3550-ipbasek9-mz.122-44.SE6.bin
    switch: copy xmodem: flash:c3550-ipbasek9-mz.122-44.SE6.bin
    Begin the Xmodem or Xmodem-1k transfer now...
    CCCCCCCxmodem:: I/O error
    Help would be really apreciated.
    Thank you.
    Marius.

    I am using Hyperterminal and a regular serial cable. Right now I am working on a 2950 Cisco Switch
    At the switch: prompt, I typed:
    copy xmodem: flash:filename.bin    [ENTER]
    As soon as you see CCCCC   in the terminal window.....
    In Hyperterminal, from the tool bar, select Transfer -> Send File
    Browse to the file, select Xmodem from the dropdown menu and select SEND
    After the process has finished, type en and then boot flash:filename.bin
    This will boot the .bin in your flash directory. The previous post only boots the switch that one time until it turns off. It does not put the image in the flash directory.
    -->I dont know why it has to be done this way, but this was a bare to figure out. Nothing works like its suppose to though.
    -This process will take a long time.  Couldnt get a faster speed then 9600

  • ¿Is it possible to upgrade from SCCM 2012 a domain controller in Windows Server 2008 R2 TO 2012 R2?

    Hi all.
    I want to know if is it possible to upgrade a domain controller from Windows Server 2008 r2 to 2012 r2 installing from SCCM 2012.
    Thanks.
    Regards.

    Hi all.
    I want to know if is it possible to upgrade a domain controller from Windows Server 2008 r2 to 2012 r2 installing from SCCM 2012.
    Thanks.
    Regards.
    Anything is possible if you can script it. You could create a task sequence to do the following (with scripts):
    1. Demote 2008R2 DC to member server
    2. Remove 2008R2 member server from domain
    3. Build new 2012R2 member server and join to domain
    4. Promote 2012R2 member server to DC
    You can do this. However, why would you? Just because you can doesn't mean you should. In my opinion it's more trouble and testing than it's worth. How many times would you need to do this?
    Gerry Hampson | Blog:
    www.gerryhampsoncm.blogspot.ie | LinkedIn:
    Gerry Hampson | Twitter:
    @gerryhampson

  • Upgrade from Windows Server 2012 Active Directory to Windows Server 2012 R2 Active Directory

    We are currently running Windows Server 2012 Active Directory and would like to upgrade to Windows Server 2012 R2 AD. Is it OK to just do an in-place upgrade, or is it advisable to build new domain controllers on R2? Are there any guides or articles anyone
    can recommend?

    Hi Ginandtonic,
    To upgrade DC(Domain Controller) from windows server 2012 to windows server 2012 r2, please refer to these articles:
    Upgrade from windows Server 2012 to 2012 R2                                 
    Upgrade Active Directory from 2012 to 2012 R2
    I hope this helps.
    Best Regards,
    Anna

  • On reinstalling system from recovery image

    Just pondering what lenovo's advice is {regarding the ad/malware pre-installed on our new laptops,which by now we've all decontaminated} should a user suffer a catastrophic system failure and need to reinstall the system via recovery partition?I assume in this scenario,one would again reload our superfishy friend and have to start working on removal yet again?Does it seem reasonable to hope lenovo may feel moved to offer all affected/infected customers a clean recovery image?Say via a download link-or better still an image on removeable media?

    If you do an OKR backup now then that backup is free of the adware. However, if you do a factory restore that adware is still there. But once you start and update Windows Defender it should also be removed.

  • Qosmio G30: How can I install only Ulead Dvd movie factory from Recovery image

    Hi everybody
    I have question about Ulead dvd movie factory.
    First, I bought my G30 with XP when it was the moment of the offer "vista for a few euros".
    So, I installed Vista with the official CD from Toshiba. But there was no longer Ulead Dvd movie Factory. As the XP's restoration CD is only an image disk, I can't install from it.
    Has anybody a solution for me?
    Thank's.
    BR.

    I think there is a solution!
    I found the Ulead DVD Movie Factory utility on the Toshiba page.
    I searched in the Qosmio G30 area but without to be successful.
    But I checked other sections and selected Satellite Satellite A series Satellite A200 (PSAEC) Vista and found the Ulead DVD Movie Factory 5.51.0147.03 version
    Download it a try to install this tool.
    Should works!

  • IMP: Cisco AIR-CAP1602 &1532 not joining 2504 Controller issue

    Dear Team, We have Cisco wireless implementation in clients premises. We have 8 indoor AP (AIR-CAP1602E-AK9) and 2 Outdoor AP (AIR-CAP1532I-AK9) . Seven indoor APs are able to join the 2504 controller, but 1 indoor AIR-CAP1602E AP is not joining and signal is RED continuously while as outdoor AP AIR-CAP1532I-AK9 signal goes blinking from green, red to amber continuously and is not downloading LWAPP image from the controller even after hard reset.
    The output for both APs shown below-
    1) AIR-CAP1602E-A-K9:
    C1600 Boot Loader (AP1G2-BOOT-M) LoaderVersion 15.2(2)JAX, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Compiled Fri 30-Nov-12 15:48 by aselvara
    ap: reset
    Are you sure you want to reset the system (y/n)?y
    System resetting...
    Boot from flash
    IOS Bootloader - Starting system.
     FLASH CHIP: Spansion S25FL256
    Xmodem file system is available.
    flashfs[0]: 14 files, 3 directories
    flashfs[0]: 0 orphaned files, 0 orphaned directories
    flashfs[0]: Total bytes: 31936000
    flashfs[0]: Bytes used: 418304
    flashfs[0]: Bytes available: 31517696
    flashfs[0]: flashfs fsck took 9 seconds.
    Reading cookie from SEEPROM
    Base Ethernet MAC address: 18:e7:28:d1:9b:05
     ************* loopback_mode = 0
    The system is unable to boot automatically because there
    are no bootable files.
    C1600 Boot Loader (AP1G2-BOOT-M) LoaderVersion 15.2(2)JAX, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Compiled Fri 30-Nov-12 15:48 by aselvarag
    Same event repeating, failed to reset and reboot device
    2) AIR_CAP1532I-A-K9 (Outdoor AP):
     *Mar  1 00:01:22.211: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER
    *Mar  1 00:01:22.211: %CAPWAP-3-ERRORLOG: Discovery response from MWAR 'Cisco_47:32:e4'running version 7.5.102.0 is rejected.
    *Mar  1 00:01:22.211: %CAPWAP-3-ERRORLOG: Failed to decode discovery response.
    *Mar  1 00:01:22.211: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 2 state 2.
    *Mar  1 00:01:22.211: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
    *Mar  1 00:01:22.211: %CAPWAP-3-ERRORLOG: Failed to process unencrypted capwap packet from 100.1.1.20
    signal goes blinking from Grean, Red to Amber continuously.
    Failed to download LWAPP image from the controller even after hard reset.
    Default image: 7.6.95.12
    Logs and screen shot attached
    Please advice. 
    Thanks
    Aakash

    Hi please note the details below-
    AIR-CAP1602E-A-K9:
    C1600 Boot Loader (AP1G2-BOOT-M) LoaderVersion 15.2(2)JAX, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Compiled Fri 30-Nov-12 15:48 by aselvara
    ap: reset
    Are you sure you want to reset the system (y/n)?y
    System resetting...
    Boot from flash
    IOS Bootloader - Starting system.
     FLASH CHIP: Spansion S25FL256
    Xmodem file system is available.
    flashfs[0]: 14 files, 3 directories
    flashfs[0]: 0 orphaned files, 0 orphaned directories
    flashfs[0]: Total bytes: 31936000
    flashfs[0]: Bytes used: 418304
    flashfs[0]: Bytes available: 31517696
    flashfs[0]: flashfs fsck took 9 seconds.
    Reading cookie from SEEPROM
    Base Ethernet MAC address: 18:e7:28:d1:9b:05
     ************* loopback_mode = 0
    The system is unable to boot automatically because there
    is no bootable files.
    C1600 Boot Loader (AP1G2-BOOT-M) LoaderVersion 15.2(2)JAX, RELEASE SOFTWARE (fc1)
    Technical Support: http://www.cisco.com/techsupport
    Compiled Fri 30-Nov-12 15:48 by aselvarag
    Can't reboot device!
    WLC-SYSLOG
    (Cisco Controller) >show sysinfo
    Manufacturer's Name.............................. Cisco Systems Inc.
    Product Name..................................... Cisco Controller
    Product Version.................................. 7.5.102.0
    Bootloader Version............................... 1.0.18
    Field Recovery Image Version..................... 1.0.0
    Firmware Version................................. PIC 16.0
    Build Type....................................... DATA + WPS
    System Name...................................... Cisco_47:32:e4
    System Location..................................
    System Contact...................................
    System ObjectID.................................. 1.3.6.1.4.1.9.1.1279
    IP Address....................................... 100.1.1.20
    Last Reset....................................... Power on reset
    System Up Time................................... 0 days 2 hrs 18 mins 39 secs
    System Timezone Location......................... (GMT -6:00) Central Time (US a                                                                                        nd Canada)
    System Stats Realtime Interval................... 5
    System Stats Normal Interval..................... 180
    --More-- or (q)uit
    Configured Country............................... US  - United States
    Operating Environment............................ Commercial (0 to 40 C)
    Internal Temp Alarm Limits....................... 0 to 65 C
    Internal Temperature............................. +32 C
    External Temperature............................. +37 C
    Fan Status....................................... 4000 rpm
    State of 802.11b Network......................... Enabled
    State of 802.11a Network......................... Enabled
    Number of WLANs.................................. 3
    Number of Active Clients......................... 0
    Burned-in MAC Address............................ 24:E9:B3:47:32:E0
    Maximum number of APs supported.................. 15

  • Cant Connect Cisco AIR-CAP 3602 with 2504 controller

    Im trying to have one of our APs join our controller. No matter what I do, i cant get it to join the controller.
    The controller has the right OS, I had to upgraded it 7.4 to support the 3600...
    Both the controller and the AP has the same time and date.
    But Im getting this from my AP:
    *Oct 30 14:49:26.043: %LWAPP-3-CLIENTERRORLOG: LWAPP LED Init: incorrect led state 255
    *Oct 30 14:49:26.055: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
    *Oct 30 14:49:26.055: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to administratively down
    *Oct 30 14:49:26.067: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
    *Oct 30 14:49:26.083: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
    *Oct 30 14:49:27.055: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
    *Oct 30 14:49:27.095: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to down
    *Oct 30 14:49:27.103: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
    *Oct 30 14:49:28.087: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
    *Oct 30 14:49:28.095: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
    *Oct 30 14:49:28.131: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
    *Oct 30 14:49:28.139: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to down
    *Oct 30 14:49:28.147: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
    *Oct 30 14:49:29.131: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
    *Oct 30 14:49:29.139: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
    *Oct 30 14:49:29.167: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
    *Oct 30 14:49:30.167: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
    *Oct 30 14:49:36.083: %CAPWAP-3-ERRORLOG: Go join a capwap controller
    *Oct 30 14:49:36.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 10.1.0.50 peer_port: 5246
    *Oct 30 14:49:36.411: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 10.1.0.50 peer_port: 5246
    *Oct 30 14:49:36.411: %CAPWAP-5-SENDJOIN: sending Join Request to 10.1.0.50
    *Oct 30 14:49:36.411: %CAPWAP-3-ERRORLOG: Invalid event 10 & state 5 combination.
    *Oct 30 14:49:36.411: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 10 state 5.
    *Oct 30 14:49:36.411: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
    *Oct 30 14:49:36.411: %CAPWAP-3-ERRORLOG: Failed to process encrypted capwap packet from 10.1.0.50
    Anyone can help me please?
    Thanks....

    AP is connected directly to one of the ports on the 2504 controller.
    I can move it to a POE switch, if needed.
    Here is the output after I boot up the AP:
    IOS Bootloader - Starting system.
    flash is writable
    FLASH CHIP:  Macronix Mirrorbit (00C2)
    Xmodem file system is available.
    flashfs[0]: 43 files, 9 directories
    flashfs[0]: 0 orphaned files, 0 orphaned directories
    flashfs[0]: Total bytes: 31997952
    flashfs[0]: Bytes used: 16767488
    flashfs[0]: Bytes available: 15230464
    flashfs[0]: flashfs fsck took 16 seconds.
    Reading cookie from SEEPROM
    Base Ethernet MAC address: 4c:00:82:77:32:7b
    Ethernet speed is 1000 Mb - FULL Duplex
    Loading "flash:/ap3g2-k9w8-mx.152-4.JA1/ap3g2-k9w8-mx.152-4.JA1"...###########################
    File "flash:/ap3g2-k9w8-mx.152-4.JA1/ap3g2-k9w8-mx.152-4.JA1" uncompressed and installed, entry point: 0x2003000
    executing...
    Secondary Bootloader - Starting system.
    Xmodem file system is available.
    flashfs[0]: 43 files, 9 directories
    flashfs[0]: 0 orphaned files, 0 orphaned directories
    flashfs[0]: Total bytes: 31997952
    flashfs[0]: Bytes used: 16767488
    flashfs[0]: Bytes available: 15230464
    flashfs[0]: flashfs fsck took 8 seconds.
    Base Ethernet MAC address: 4c:00:82:77:32:7b
    Boot CMD: 'boot  flash:/ap3g2-k9w8-mx.152-4.JA1/ap3g2-k9w8-xx.152-4.JA1;flash:/ap3g2-k9w8-mx.152-4.JA1/ap3g2-k9w8-mx.152-4.JA1'
    Loading "flash:/ap3g2-k9w8-mx.152-4.JA1/ap3g2-k9w8-xx.152-4.JA1"...###############################
    File "flash:/ap3g2-k9w8-mx.152-4.JA1/ap3g2-k9w8-xx.152-4.JA1" uncompressed and installed, entry point: 0x2003000
    executing...
                  Restricted Rights Legend
    Use, duplication, or disclosure by the Government is
    subject to restrictions as set forth in subparagraph
    (c) of the Commercial Computer Software - Restricted
    Rights clause at FAR sec. 52.227-19 and subparagraph
    (c) (1) (ii) of the Rights in Technical Data and Computer
    Software clause at DFARS sec. 252.227-7013.
               cisco Systems, Inc.
               170 West Tasman Drive
               San Jose, California 95134-1706
    Cisco IOS Software, C3600 Software (AP3G2-K9W8-M), Version 15.2(4)JA1, RELEASE SOFTWARE (fc2)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2013 by Cisco Systems, Inc.
    Compiled Tue 30-Jul-13 22:57 by prod_rel_team
    Initializing flashfs...
    flashfs[3]: 43 files, 9 directories
    flashfs[3]: 0 orphaned files, 0 orphaned directories
    flashfs[3]: Total bytes: 31739904
    flashfs[3]: Bytes used: 16767488
    flashfs[3]: Bytes available: 14972416
    flashfs[3]: flashfs fsck took 8 seconds.
    flashfs[3]: Initialization complete.
    flashfs[4]: 0 files, 1 directories
    flashfs[4]: 0 orphaned files, 0 orphaned directories
    flashfs[4]: Total bytes: 11999232
    flashfs[4]: Bytes used: 1024
    flashfs[4]: Bytes available: 11998208
    flashfs[4]: flashfs fsck took 1 seconds.
    flashfs[4]: Initialization complete.
    Copying radio files from flash: to ram:
    Copy in progress...CCCCC
    Copy in progress...CCC
    Copy in progress...CCCC
    Copy in progress...CCCC
    Copy in progress...CC
    Uncompressing radio files...
    ...done Initializing flashfs.
    Radio0  present 8764 8000 0 A8000000 A8010000 0
    Rate table has 244 entries (64 SGI/104 BF variants)
    Radio1  present 8764 8000 0 88000000 88010000 4
    Radio2 not present 0 0 0 0 0 8
    This product contains cryptographic features and is subject to United
    States and local country laws governing import, export, transfer and
    use. Delivery of Cisco cryptographic products does not imply
    third-party authority to import, export, distribute or use encryption.
    Importers, exporters, distributors and users are responsible for
    compliance with U.S. and local country laws. By using this product you
    agree to comply with applicable laws and regulations. If you are unable
    to comply with U.S. and local laws, return this product immediately.
    A summary of U.S. laws governing Cisco cryptographic products may be found at:
    http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
    If you require further assistance please contact us by sending email to
    [email protected].
    cisco AIR-CAP3602I-A-K9 (PowerPC) processor (revision A0) with 180214K/81920K bytes of memory.
    Processor board ID FTX1731GQYY
    PowerPC CPU at 800Mhz, revision number 0x2151
    Last reset from power-on
    LWAPP image version 7.5.102.0
    1 Gigabit Ethernet interface
    2 802.11 Radios
    32K bytes of flash-simulated non-volatile configuration memory.
    Base ethernet MAC Address: 4C:00:82:77:32:7B
    Part Number                          : 73-14521-02
    PCA Assembly Number                  : 800-37501-02
    PCA Revision Number                  : A0
    PCB Serial Number                    : FOC17273HG4
    Top Assembly Part Number             : 800-35852-02
    Top Assembly Serial Number           : FTX1731GQYY
    Top Revision Number                  : C0
    Product/Model Number                 : AIR-CAP3602I-A-K9
    % Please define a domain-name first.
    Press RETURN to get started!
    *Mar  1 00:00:11.355: FIPS IOS test Image Checksum successful
    *Mar  1 00:00:11.355: FIPS IOS test Crypto RNG DEK Key Test successful
    *Mar  1 00:00:11.355: FIPS IOS test SHA-1 successful
    *Mar  1 00:00:11.355: FIPS IOS test HMAC-SHA1 successful
    *Mar  1 00:00:11.355: FIPS IOS test AES CBC 128-bit Encrypt successful
    *Mar  1 00:00:11.355: FIPS IOS test AES CBC 128-bit Decrypt successful
    *Mar  1 00:00:11.355: FIPS IOS test IOS AES CMAC Encrypt successful
    *Mar  1 00:00:11.355: FIPS IOS test IOS CCM Encrypt successful
    *Mar  1 00:00:11.355: FIPS IOS test IOS CCM Decrypt successful
    *Mar  1 00:00:11.387: FIPS IOS test RSA Signature Generation successful
    *Mar  1 00:00:11.391: FIPS IOS test RSA Signature Verification successful
    *Mar  1 00:00:11.391: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed
    *Mar  1 00:00:11.391: %IFMGR-7-NO_IFINDEX_FILE: Unable to open nvram:/ifIndex-table No such file or directory
    *Mar  1 00:00:11.847: Registering HW DTLS
    *Mar  1 00:00:14.647: %LINK-6-UPDOWN: Interface GigabitEthernet0, changed state to up
    *Mar  1 00:00:18.327: FIPS RADIO test AES 128-bit encrypt for TX on Dot11Radio 0 successful
    *Mar  1 00:00:18.327: FIPS RADIO test AES 128-bit CCM encrypt on Dot11Radio 0 successful
    *Mar  1 00:00:18.327: FIPS RADIO test AES 128-bit CCM decrypt on Dot11Radio 0 successful
    *Mar  1 00:00:18.327: FIPS RADIO test AMAC AES 128-bit CMAC encrypt on Dot11Radio 0 successful
    *Mar  1 00:00:18.327: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0
    *Mar  1 00:00:24.451: FIPS RADIO test AES 128-bit encrypt for TX on Dot11Radio 1 successful
    *Mar  1 00:00:24.451: FIPS RADIO test AES 128-bit CCM encrypt on Dot11Radio 1 successful
    *Mar  1 00:00:24.451: FIPS RADIO test AES 128-bit CCM decrypt on Dot11Radio 1 successful
    *Mar  1 00:00:24.451: FIPS RADIO test AMAC AES 128-bit CMAC encrypt on Dot11Radio 1 successful
    *Mar  1 00:00:24.451: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 1
    *Mar  1 00:00:26.811: %SYS-5-RESTART: System restarted --
    Cisco IOS Software, C3600 Software (AP3G2-K9W8-M), Version 15.2(4)JA1, RELEASE SOFTWARE (fc2)
    Technical Support: http://www.cisco.com/techsupport
    Copyright (c) 1986-2013 by Cisco Systems, Inc.
    Compiled Tue 30-Jul-13 22:57 by prod_rel_team
    *Mar  1 00:00:26.811: %SNMP-5-COLDSTART: SNMP agent on host AP4c00.8277.327b is undergoing a cold start
    *Jul  4 23:55:50.035: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
    *Jul  4 23:55:50.035: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
    *Jul  4 23:55:50.051: %PARSER-4-BADCFG: Unexpected end of configuration file.
    lwapp_crypto_init: MIC Present and Parsed Successfully
    *Jul  4 23:55:50.191: %SSH-5-ENABLED: SSH 2.0 has been enabled
    *Jul  4 23:55:50.855: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to down
    *Jul  4 23:55:51.027: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
    *Jul  4 23:55:51.035: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
    *Jul  4 23:55:51.035: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
    *Jul  4 23:55:53.319: FIPS HW test SHA-1 successful
    *Jul  4 23:55:53.319: FIPS HW test HMAC-SHA1 successful
    *Jul  4 23:55:53.319: FIPS HW test AES CBC 128-bit Encrypt successful
    *Jul  4 23:55:53.319: FIPS HW test AES CBC 128-bit Decrypt successful
    *Jul  4 23:55:53.819: FIPS HW test SHA-1 successful
    *Jul  4 23:55:53.819: FIPS HW test HMAC-SHA1 successful
    *Jul  4 23:55:53.819: FIPS HW test AES CBC 128-bit Encrypt successful
    *Jul  4 23:55:53.819: FIPS HW test AES CBC 128-bit Decrypt successful
    *Jul  4 23:55:53.819: %SOAP_FIPS-2-SELF_TEST_HW_SUCCESS: HW crypto FIPS self test passed
    *Jul  4 23:55:53.819: DPAA Initialization Complete
    *Jul  4 23:55:53.819: %SYS-3-HARIKARI: Process DPAA INIT top-level routine exited
    *Jul  4 23:55:54.819: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to up%Default route without gateway, if not a point-to-point interface, may impact performance
    *Jul  4 23:56:13.191: %CDP_PD-4-POWER_OK: Full power - NEGOTIATED inline power source
    *Jul  4 23:56:14.279: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
    *Jul  4 23:56:15.279: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
    *Jul  4 23:56:15.371: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
    *Jul  4 23:56:16.371: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
    *Jul  4 23:56:18.895: Logging LWAPP message to 255.255.255.255.
    *Jul  4 23:56:23.627: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 10.1.1.150, mask 255.255.240.0, hostname AP4c00.8277.327b
    Translating "CISCO-CAPWAP-CONTROLLER.pti.local"...domain server (10.3.1.32)
    *Jul  4 23:56:34.559: %CAPWAP-3-ERRORLOG: Did not get log server settings from DHCP.
    *Jul  4 23:56:34.567: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER.pti.local
    *Jul  4 23:56:44.567: %CAPWAP-3-ERRORLOG: Go join a capwap controller
    *Oct 30 15:05:13.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 10.1.0.50 peer_port: 5246
    *Oct 30 15:05:13.411: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 10.1.0.50 peer_port: 5246
    *Oct 30 15:05:13.411: %CAPWAP-5-SENDJOIN: sending Join Request to 10.1.0.50
    *Oct 30 15:05:13.411: %CAPWAP-3-ERRORLOG: Invalid event 10 & state 5 combination.
    *Oct 30 15:05:13.411: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 10 state 5.
    *Oct 30 15:05:13.411: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
    *Oct 30 15:05:13.411: %CAPWAP-3-ERRORLOG: Failed to process encrypted capwap packet from 10.1.0.50
    *Oct 30 15:05:18.411: %CAPWAP-5-SENDJOIN: sending Join Request to 10.1.0.50

  • Recovery Image vs windows 8.1 retail image

    I am looking for a recommendation on how I should reinstall the OS for my HP Laptop. 
    When I got it, I burned the recovery image over 6 dvd's.  I also bought from HP the recovery disks for the laptop.  The problem is when you recover the image it can take a couple of hours to download the image from the dvd's and setup all the software.  Then it takes a another few hours to download all the updates for the OS, Cyberlink software and drivers from hp.  I know this because I have previously had to do that because of a virus and I had to zero format the hard drive to remove everything.
    I have since discovered that I can use a Microsoft 8.1 disk (the pro will not work and you actually receive an error due to the way the bios offers the key code) and reinstall the OS directly and eliminate all the bloatware the recovery image has.   This is actually a little faster since 8.1 is installed instead of 8.0. 
    I happen to like the Cyberlink software , so I bought serveral titles for use from an upgrade price.  But I did not buy all the cyberlink software as I do not use all of it.  What I didn't buy I can reinstall from the HP website.  Except for a package that edits video from cyberlink that is included in the recovery image, but cannot be downloaded and installed without the recovery image being used.  But again, that is software I do not use. 
    I use the laptop primarily for gaming - World of Warcraft, Eve Online, and Steam.  I also do some automation using HP UFT. 
    I also have a Pro license Key and Media Pack key to upgrade from 8.1 version of Windows.
    So based on my usage, which would be better?  The recovery image or the windows 8.1 image?  Will I miss any specialized hp software that can protect the laptop? 
    If you want to tell me to use Linux, I have a distro that will be installed along side it for use when I need that particular OS and the laptop will be used as a dual-boot machine.

    I can't use the One Key Recovery of my Y2P anymore, as I decreased the size of the C partition in favour of increasing D:\Data
    OKR won't even start anymore...
    Any chance to get OKR working again if I make these partitions the same sizes?
    Who has the exact partition sizes in MB of the Y2P 20266 with Samsung PM851 256 GB SSD?
    0 1 MB  NO_NAME unallocated
    1 1000 MB  WINRE_DRV NTFS  
    2 260 MB  SYSTEM_DRV  FAT32 (EFI)
    3 1000 MB  LRS_ESP FAT32
    4 128 MB  NO_NAME Other
    5 ? GB  C:\Windows8 NTFS
    6 ? GB  D:\Data NTFS
    7 14135 MB  PBR_DRV NTFS Recovery
    8 327 kB  NO_NAME Unallocated
    Data is backupped daily and I already have a full system backup together with a bootable USB stick that has been tested.
    But I like to make sure I can reinstall Windows in the future..
    Freedom of Speech has just left the building

  • How to reinstall Windows 8 on Yoga 13 with damaged Recovery Image?

    I changed the partitions on my Yoga 13. Now it is not possible to refresh, reinstall or perform an advance start-up, as it looks like there is no recovery image anymore. The systems is currently very messy and needs a reinstall.
    Can someone tell me how to reinstall Windows 8 on the Yoga 13 when the recovery image is lost or damaged?

    hi Chevex,
      Thanks for using Lenovo Community Forums!
    In the event that the Recovery partition is not working the only option is to use the Recovery CD that you can create when you first got the computer.
    but if you were not able to create a Recovery CD and the Onekey Recovery is not working.
    You can get the Recovery CD from the Software Department (Fees may apply to the discs)
    you can contact the Hardware Team again and ask to be transferred to Software team for purchasing RCD
    Lenovo Technical Support (US)
    IDEA-branded and
    B, C, E, G, H, K, N, Q, V, Y Series Products
    English
    1-877-4-Lenovo
    (1-877-453-6686)
    24 hours a day
    7 days a week
    Hope this helps,
    Did someone help you today? Press the star on the left to thank them with a Kudo!
    If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
    Follow @LenovoForums on Twitter!

  • HP Stream 7-Windows 10 doesn't boot, I can't recovery 8.1 because can't boot from USB-HELP please!!

    Hi everybody, I'm new here!
    I am (scuse me: WAS) enjoying a Stream 7
    Some days ago I tried to install Windows 10 TP upgrading 8.1 with Bing. After some waiting time it succeeded, but unfortunately I forgave to put in the tablet's SSD the hp drivers, thinking they weren't necessary. So touchscreen, WiFi and all the other stuff didn't work. After I collegated via OTG a keyboard and a mouse I managed to use Windows 10.
    Trying to install drivers, my fault, I opened an .exe of Realtek (maybe for the audio), tablet asked to reboot and after that I cannot access to Windows anymore.
    I tried to boot Windows 8.1 from a USB, but it doesn't boot, the same even if i disable secure boot.
    With disabled bitlocker Windows gives this error
    In boot option I set these settings
    I put the usb in this way:
    The Stream doesn't consider the USB absolutely XD
    If I enable again the secure boot Windows gives this error (that at 99% is caused by the .exe I installed):
    Rebooting the Stream a couple of time with secure boot it goes in a menu (where touchscreen works) where there are a lot of options to reset Windows, but none of them works. If I try to format from this menu it asks for my account's password, but it doesn't accepts the mine :/
    If I try to open the recovery (from volume minus button when it starts) it gives this message:
    Waiting for help,
    Thank you for your patience!
    This question was solved.
    View Solution.

    Hi everyone. I think I have found a solution to this problem. Short background story, I too tried to install Windows 10 (10049) via Windows Update but I was never successful - got stuck at around 30% for more than an hour. I tried to restore to 8.1 but it gave me that 0xc000000f error. Luckily I had made a recovery image to USB before updating to Windows 10.
    Please note that by doing this method, you will obviously lose your data.
    Here's what you'll need:
    - Recovery USB (if you don't have one, grab it from this link and I thank you that person from another post). Follow the instructions, this is just basically clean, format to FAT32, set primary and active, and then drag and drop the files and folders from the USB folder to the root USB drive. This particular recovery is from a 5701 model, there is actually no difference between Stream 7 models in terms of hardware, but software is configured differently (different language setup/format) depending on the country/region it's sold.
    - OTG cable
    - Powered USB hub
    - USB Mouse and Keyboard
    - A moment of your time
    1. Plug in the OTG cable to the tablet, and then plug in the USB hub to power and to the OTG. After that, plug in the USB mouse and keyboard and Recovery USB to the USB hub.
    2. Boot the tablet to BIOS by holding down Power + Volume Down at the same time, until you reach the Startup Menu.
    3. Press F10 and navigate to System Configuration > Boot Options. In this menu, we'll have to restore the settings to default.
    So if you have disabled Secure Boot, you first need to Clear All Secure Boot Keys and then Load HP Factory Default Keys. Then enable Secure Boot.
    Make sure UEFI Boot Order is also default to as follows: OS boot Manager, USB Diskette, USB CD/DVD, Network Adapter.
    If you did not make any changes, proceed to 4.
    4. Be prepared to go back to the Startup Menu, because as soon as you press F10 and hit Yes, the tablet will automatically restart. So press and hold the Volume Down button after you hit on Yes.
    5. Press F9 and select Boot From EFI File. If you've done the recovery image ghosting correctly onto the Recovery USB, you should see two entries. One should be RECOVERY and the other may depend (it could be SYSTEM or No label). Select RECOVERY, and then select bootmgr.efi.
    At this point the tablet will boot off from the USB and will bring you to Windows Recovery.
    6. Select your keyboard layout, and navigate to Troubleshoot > Reset your PC.
    If the drive partition/boot manager is not damaged, it will ask for a recovery key. You can actually skip this step and hide the numpad, revealing the option Skip this drive if you don't have the recovery key anymore, or just really want to start anew.
    If the drive partition/boot manager is damaged, the Reset will proceed and will ask you to select a target operating system. In my case it was Windows 8.1.
    7. The next screen will be about Reset your PC telling you what's going to happen. Tap Yes > Yes, repartition the drives > Fully clean the drive > Reset.
    The tablet will now do its thing and restore to factory default.
    After restoration, a BIOS screen will come up asking if you want to clear the TPM keys. Select Yes, and this will create a new key for the restored installation, bringing you back to a fully factory default tablet.
    Notes:
    I recommend not installing a generic Windows 8.1 ISO that is copied straight to the USB drive using the Windows 7 USB/DVD Tool or RUFUS. They won't be compressed or the same as WIMBOOT, which will take up more storage space than stock recovery.
    You could actually install another version of Windows 8.1 on the tablet, assuming you know what you are doing (ie. making a WIMBOOT image).
    You could also actually install Windows Technical Preview directly, again, assuming you know what you are doing.
    This is just a guide to help you try recover your tablet from a failed Technical Preview installation. I hold no responsiblities over your actions.
    What I recommend is that use 8.1 for now, and wait for the official release (or at least a more stable Technical Preview release for this tablet if you can't wait that long) of Windows 10.

  • Field Recovery Image Version

    Should I upgrade field recovery image version on WLC 5508?  One of WLC 5508 has software 7.2.111.3 and field recovery image version is 6.0.182.0.
    Thanks,

    Yes you should. Upload the FUS image and reboot the WLC. Read the release notes also.
    Sent from Cisco Technical Support iPhone App

  • Can I create a Win 7 Recovery Image *Bootable* USB THUMB DRIVE? -- (Instead of cd/dvd)

    Hi
    Can someone share how to create a 
    Windows 7 Recovery Image USB THUMB BOOTABLE DRIVE?  -- I mean in place of the Boot DVD that Windows Backup offers to create after you've created an image?
    I assume that there must be a way to do this?
    Thanks in advance!!

    Juke, Thanks, but my question remains not answered,
      I only want to know one thing.
    ***How do I create a USB BOOT "DISK" using a USB Drive.  Not the IMAGE --just the boot files
         In other words, I want my 2 gig USB THUMB DRIVE to behave just like the Recovery CD/DVD.
         I only want the steps of how to create the BOOTABLE USB. 
         (Forget about the image  --- I keep the image on on another hard drive, and NOT the USB)
    See the following guide to make a recovery USB drive:
    http://www.intowindows.com/how-to-repair-windows-7-from-usb-flash-drive-repair-without-installation-dvd-disc/
    Have Questions About Installing Windows 7?
    FAQ - Common Windows 7 Installation Questions & Answers

  • Portege R700 - original recovery image re-installation failed

    Hello
    I have a Toshiba Portege R700 for years.
    As i already have some trouble, i did a reinstallation few years ago, from recovery partition. Directly.
    But, few days ago, i had some issues with my portege.
    HDD seems to be broken as it make some noise and was really, really, really, ..., really slow.
    So, after making some data backup during hours and hours (remember, it was really, ..., really slow), i lauch a complete re-installation from "recovery partition". It seems to be good, but .. never finished the process, with same HDD noise, and again slow HDD I/O.
    OK, my own diadnostic: change HDD.
    This done, and using the Toshiba recovery DVD just bought (yes impossible to find the earlied burn DVD), i have ... the same issue. The recovery process does not end even if 'im waiting for days ...
    And i have the same HDD noise. With the new one!!
    So having a MSDN licence, i installed a Win7 Pro 32bits, but not the Toshiba one.
    And it's running for days without any issue!
    But i have to reinstall all drivers, and software delivered by Toshiba.
    Obviouly i will prefer to find what is the exact issue with this Portege, and reinstall the Toshiba version of Windows 7 Pro.
    So, if someonre read the story until, the question is: ANY IDEA?
    How to make a HW diagnostic? How to identify the exact problem?
    Thanks for your help.
    Jol

    Hi Dr Lamp.
    Remember that i
    - did a successfull recovery from recovery partition few years ago
    - tried 2 recovery recently
    try 1, from recovery with initial HDD.
    I'm not REALLY sure, but i think that the recovery failled during step "recovery image installation from copied data step 50/52"
    I'm not sure.
    As it take hours during this step, if it go to the next step or not, as i let it run for hours and hours (yes, i'm persistent)
    try 2, from original Toshiba DVD i ordered (35)
    I'm sure it fail during an additionnal step you forgot.
    Because after "installed OS will be prepared for usage", which configure a lot of things using numerous reboot, there is the final step which is "first launch of win7"
    Note that not the exact term, but is something like that.
    Thanks for your help
    Jol

  • New bought 2504 Controller not copatible with 1702 APs

    Hi!
    Just got a 2504 Controller with 1702 APs, which are not joining the controller by known reasons.
    (Cisco Controller) >*spamApTask1: Dec 16 22:20:10.288: f0:7f:06:c0:55:80 ApModel: AIR-CAP1702I-E-K9
    *spamApTask1: Dec 16 22:20:10.288: Unknown AP type. Using Controller Version!!!
    *spamApTask1: Dec 16 22:20:10.289: f0:7f:06:c0:55:80 ApModel: AIR-CAP1702I-E-K9
    *spamApTask1: Dec 16 22:20:10.289: Unknown AP type. Using Controller Version!!!
    *spamApTask1: Dec 16 22:20:16.135: fc:5b:39:6e:26:9c ApModel: AIR-CAP1702I-E-K9
    But now I have to buy a SmartNET Subscription to get the bug-free Software for my controller, because software problems are not covered in the warranty? Is there any other Solution?
    New controller running on 7.6.130.0
    Regards
    Alfred

    Well that is too bad.  Maybe ask the company whom you bought the WLC or if you have a Cisco SE to provide you with the code. The only other option is to return it and order the WLC with v8.0, but you will be stuck on that not so good code. The 2504 w/5 AP license, you can find a SMB smartnet for cheap that can give you access to the image download. It's really up to you, but the v8.0 that is currently out is the first version and... well, do I have to say more. I won't use that version, and my customers whom have had to go with that version because of access point support is not too happy to say the least. When the newer version comes out, they will have to upgrade. 
    -Scott

Maybe you are looking for