RED Blinking LIGHT

I used blackberry software updater to update my phone then it had to restart and it almost did except the it came to 100% and the battery died to it shut down then when I turned it on it would came on but a red blinking light comes on every other second. I don t know what to do somebody please help me

The red blinking light means that you most likely have a corrupt software because your downloading was interupted by a drained battery. You may have to re-install the software with the Blackberry Link by connecting your phone to the computer

Similar Messages

Red blinking light as well as trailing broken black line going in a square on left side

red blinking light as well as trailing black broken black line going on left side that goes in a square trail

Did you ever fix this? My daughters is the same. Treated with tender loving care, we reset to factory and it disappeared but was back again after 2 or 3 days. Still in warranty so going to take to the genius bar, however a bit concerned that because it belongs to an 11 year old they are going to assume she's damaged it.

Red blinking light & phone is unresponsive (8100 Series)

I've had my Pearl for about 18 months and it's always been fairly reliable.
Yesterday it got wet for the first time (I suspect this may be the cause of the problem...).
Right away, I took out the battery and SIM card, dried the phone as best I could, and put the parts in a warm area.
Now all I'm seeing is a series of red blinking lights:
- blink, blink, blink (3 times, a half second pause, then)
- blink, blink (and a 2 second pause before it starts again)
I tried using a backup battery, and I tried it with and without the SIM card.
Does anyone know what this sequence of blinks means?
And, more importantly, how can I save my phone??

the three blinks, a pause, and two more.. don't know what the blink meant or why mine started.. I connect to computer via bluetooth and wasn't connected when it began. I came here for answers and very surprised bb doesn't have a tech rep providing help. & phone charged full the night before..
anyway, followed advice to disconnect from battery and reconnect in certain order while plugged into wall socket.. tried a few times with a few minutes of complete 'no power' each time. the light would sometimes flash when only the wall plug was in with no sim or battery. I gave up and left it connected to the wall socket with sim and battery in and flipped it over so I wouldn't get annoyed seeing the blink. left it for 30 minutes and it still was flashing. stuck it in my pocket went to a friend's house and checked when I got there 10 minutes later. still flashing. threw it half way across the room (carpet floor) and it booted up fine. is on now and I'm not touching it until tomorrow.
not suggesting anyone throw it, could break it, but it worked for me. likely in conjunction with topping up the battery. who knows. they're touchy.

Red Blinking Lights on Photosmart 7760

I have a Photomart 7760 that is now starting up from power on, blinks 10 times "green", and then continuous "red" blinking. If I remember correct from another post, it said something about printer head. So...question is what does this blinking sequence mean, and how to I correct it?

Here is a link to a document you can follow for this issue:
http://h10025.www1.hp.com/ewfrf/wc/document?docname=bpa00299&cc=us&dlc=en&lc=en&product=305375&tmp_t...
I am an HP employee.
Say "Thanks" by clicking the Kudos Star in the post that helped you.
Please mark the post that solves your problem as "Accepted Solution"

Help urgently needed! BB curve 8900 dead with red blinking lights on!!!

Hi to everyone! i just bought a BB Curve 8900 last month and now i'm facing aproblem. i am new to this forum and i was hoping you guys can help me out. i connected my BB to my pc with desktop manager to download some music when it prompted me to update my software. So i did, then at the end of the installation, i got fatal error and now all i got is a dead phone with red light blinking every 2 sec. can anyone help me pls?thank in advance and more power to this forum.

First locate your carrier and the OS file you wish to use.
http://na.blackberry.com/eng/support/downloads/download_sites.jsp
Do a backup of your device first, using Desktop Manager > Backup. Close Desktop Manager upon completion.
1. Download the OS file to the PC then install it to the PC by running (double clicking) the file you downloaded.
2. Go to c:\program files\common files\research in motion\apploader and delete the file named "vendor.xml."
3. Plug in BB and double click on "Loader.exe." It's located in the same place as the above vendor.xml file.
1. If any post helps you please click the below the post(s) that helped you.
2. Please resolve your thread by marking the post "Solution?" which solved it for you!
3. Install free BlackBerry Protect today for backups of contacts and data.
4. Guide to Unlocking your BlackBerry & Unlock Codes
Join our BBM Channels (Beta)
BlackBerry Support Forums Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code

Red Blinking Message Light Indicator Back to Green

On the BlackBerry Curve 8330, can anyone tell me please if it is normal once you receive any type of message, and the light on top blinks red, after about 15 minutes it goes back to blinking green even though I never checked my messages? You would think, especially with a BlackBerry that the light would continue to blink red until messages are checked?! Is there anything I can do to remedy this? Any programs out there third party or what not?...any free? Or is my phone defected? Thank you for your time and your input.

Yes the coverage indicator is on, I want it to blink green. Again, I want to know why the red blinking light message indicator goes back to blinking green after 15 minutes and does not continue to blink red until I actually go into the particular message folder? Thanks anyways for your help.

Blinking light

We got a new blackberry curve and the notification light is constantly blinking. we have switched off the notification on each every setting and it still blinks. We did a battery pull and it still blinks.
It is, obviously, draining the battery.
Are we missing a setting somewhere? TIA
Solved!
Go to Solution.

That is your light letting you know you have service. your notification light is a red blinking light.
To turn the green light off, go to OPTIONS > SCREEN/KEYBOARD > then scroll down to LED COVERAGE INDICATOR and change it to OFF.
If anyone has been helpful to your question, please click KUDOS in their posts. If your question has been answered, please click SOLVED.
Nurse-Berry
Follow NurseBerry08 on Twitter

How can I fix this red blinking SYS LED light?

I am having problems with the extender losing signal and the GPS turns red and the SYS light is slow blinking red. I just spent 40 minutes on the phone with a Verizon tech who had me unplug it and just pretty much said "Sorry, there nothing we can do"!!!! This is happening several times a day for the past 2 weeks.

I am having the same problem with a blinking red sys light and red gps light. The system has been working fine for months and without my changing anything at all, it stopped working yesterday. I am using the correct power supply. I have powered off and on the gateway and the extender several times. My zip is 94306 (although Verizon shows my device as nearby Los Altos 94022 where I think the tower might be). I have AT&T Uverse as my ISP with a standard 2wire modem/router gateway 3800HGV-B. My internet speed is 15.39 Mbps down, 1.93 Mbps up (it is speedtest.net not text): http://www.speedtest.net/my-result/3707324666 VoIP test reports 15.1 and 1.92: Speed test statistics --------------------- Download speed: 15132 kbps Upload speed: 1924 kbps Download consistency of service: 93 % Upload consistency of service: 99 % Download test type: socket Upload test type: socket Maximum TCP delay: 54 ms Average download pause: 1 ms Minimum round trip time to server: 24 ms Average round trip time to server: 24 ms Estimated download bandwidth: 15434 kbps Route concurrency: 1.0199696 Download TCP forced idle: 0 % Maximum route speed: 21845 kbps General information ------------------- IP address: 99.108.141.9 Local time: Aug 22, 2014 4:12:39 PM Test server: http://mcssjc.visualware.com/ Thanks for any help, Larry Kaplan

Blinking Red Power Light Need Help With Self Repair

I have a rear projection 57 inch TV, model number 57H84R and whenever I try and turn it on all I get is a blinking red power light. I've seen online where it might be a fuse in it but when I called customer support they told be it was a board. I don't have the manual anymore and i've read it is needed to try to repair it myself. I've anyone had any advice on where to start at or any place online that would be helpful in trying to fix it myself would be appreciated. My e-mail address is [email protected], thank you.

When you moved in January, how long was the Mac not connected to AC power? You could have a weak PRAM memory battery. Have you tried zapping PRAM? See Mac PRAM, NVRAM, CUDA/PMU & Battery Tutorial
 Cheers, Tom

HELP Needed ASAP! Curve Not Turning On, Red Flashing Lights!

Hi,
I have a Blackberry curve 8310. I plugged my curve into my mac to do a software update. Midway through, my phone shut off and hasn't worked since. The battery is fully charged. The phone is off and won't turn on. Additionally, there is a red LED light blinking twice every few seconds. I think I found an article on blackberry.com's knowledge database that diagnosed my issue, but my problem now is that because the curve isn't turning on/off, it's not connecting to my mac's desktop manager. So I can't do anything the article tells me to do. What should I do now? I need help ASAP!
Here's the link to the article: http://www.blackberry.com/btsc/search.do?cmd=displayKC&docType=kc&externalId=KB19915
Thanks in advanced!

Hello Asmro and welcome to the BlackBerry Support Community Forums.
It can take up to 30 minutes for the Mac to connect to the BlackBerry.
I would remove your battery and connect to the BlackBerry Desktop Manager. Once it comes up there is no software installed, re-insert the battery and follow the article KB19915.
Let me know how you make out.
-HMthePirate
Come follow your BlackBerry Technical Team on twitter! @BlackBerryHelp
Be sure to click Kudos! for those who have helped you.Click Solution? for posts that have solved your issue(s)!

Trouble shooting blinking lights on an HP photosmart c5580

My photosmart c558 has the following lights blinking. 1) Print photos 2) Red eye removal, 3) power button and 4) orange light by the + button.
I have a message of turn power off/on again. I have done so. Message comes back as do the blinking lights. System sometimes prints/sometimes does not.
Can anyone help?

I have an HP C5580 and it is doing the same thing. Screen says " turn off and on again" and lights: red eye removal, power blinks. I have unplugged to reset and continues to malfunction

What is this code mean, ( 14 slow blinking lights and 5 fast blinking lights) mean

need to know what this means please, 14 slow blinking lights and 5 fast blinking lights) mean

thank you thank you for taking an interest. this is so frustrating.
i only have apple keyboard, mighty mouse, and 20 inch cinema display connected. this morning took out memory and tried to boot up with individual pairs in the first bank. first the (2)256, the (2) 1g, and then the other (2) 1g modules. everytime I get the weird fuzzy wheel under the logo after a while, black screen flashes, then grey apple logo fuzzy screen then black forever.
I ran tiger updates this morn. still will only boot to safe mode. then tried to run leopard disk to install it
will not boot from leopard disk.
tried safe boot, then doulble click install leopard, restart, then the saga repeats with the pixely red square around the wheel.
these are fresh drives with only what came on instll disk loaded.
thanks again for taking an interest.
i love this system(well at least i did). I want to install leopard on my powerbook too but am terrified to do so right now since it is working and I have work to do. Can't afford to have no computer to do my work on...self employment is great?!
This is making me crazy. I anxiously await your words of wisdom.

Screen Display off with red Notification light

Dear Team I've BB Curve 9320 and am facing display off issue in my phone and regularly red notification light is blinking and keypad light is also lighting. I've visited East Delh(India) and Noida Sec 2 Service center but found there was no service center which address was mentioned there.I tried to update my software but failed into my attempt it's asking password everytime whenever I do a same.   Kindly resolve my issue and share valide contact no. to share my griviance with you people.

Hi and Welcome to the Community!
Please try this sequence...note that, throughout the entire 4h15m process, your BB must remain directly connected to a known-good wall charger (not PC USB, not a cradle):With the battery inside, connect your BB to the wall chargerLeave it alone for 2 hours, no matter what the LED or the display doesRemove the batteryWait 15 minutesInsert the batteryWait another 2 hours, no matter what the LED or the display doesThis has been known to "kick start" some BBs.
It is also possible that your battery or BB has experienced a problem...to test, this sequence is needed:Obtain an known good and already fully charged additional battery...use it in your BB and see what happensObtain access to a known good and identical BB...use your battery in it and see what happensThe results of this will indicate if it's your BB or your battery that has the problem. Note carefully please that "new" and "know good" are not necessarily the same things. While rare, a "new" battery certainly could be defective. Rather, the simplest (and least costly, btw) method to conduct this test is to find someone with an identical BB who has no issues...trade batteries and see what happens.  If possible, you could also attempt to boot into Safe Mode:KB17877 How to start a BlackBerry smartphone in Safe ModeIt may take you multiple attempts to get the ESC key sequence (press/release/hold) correct, so be patient. When/if successfully into Safe Mode, see what happens.
If the behavior ceases, then think carefully...what happened just before this behavior started? A new app? An update? A Theme? Something else? Think carefully as the smallest change could be causal...and attempt to undo whatever that was.
But if the behavior continues in Safe Mode, then you may need to consider more drastic actions -- WIPE, OS Reload, BBSAK Wipe/Reload, and the "Bare Bones" OS Reload Process. To prepare, you should be sure that you have a full backup to your PC...please review the Backup link in my auto-sig on this post for instructions.
You may also need the use of these tricks:KB10144 How to force the detection of the BlackBerry smartphone using Application LoaderKB27956 How to recover a BlackBerry smartphone from any statehttp://crackberry.com/blackberry-101-lecture-12-how-reload-operating-system-nuked-blackberryprateekasthana wrote:
Dear Team I've BB Curve 9320 and am facing display off issue in my phone and regularly red notification light is blinking and keypad light is also lighting. I've visited East Delh(India) and Noida Sec 2 Service center but found there was no service center which address was mentioned there.I tried to update my software but failed into my attempt it's asking password everytime whenever I do a same.   Kindly resolve my issue and share valide contact no. to share my griviance with you people.  Concerning your questions...refer:http://supportforums.blackberry.com/t5/Social-Lounge/How-This-Site-and-Formal-Support-Work/td-p/2540549This forum is a user-to-user community, so we have no information about service centers local to you.
Good luck and let us know!

HP Officejet H470 - Blinking Lights

I have a mobile HP Officejet H470 printer. I have had several issues lately with blinking lights, I find a fix, do it and other lights seem to start blinking then. This time it is the resume light and the right ink cartridge light. it cycles like this..... the resume light is green, then red, then the right ink cartridge blinks, then starts over.
Any help will be appreciated.
Thanks

When the resume and right cartridge lights blink, it means that the ink reservoir is full. You need to replace the reservoir and then reset the printer. You can find instructions in this document.
I am an employee of Hewlett Packard.
- - Please mark Accept As Solution if it solves your problem so others can more easily find the answer - -
- - Please click the Kudos star if you would like to say thanks - -

MiFi2200 has a red flashing light

MiFi2200 has a red flashing light and will not get a signal. When it's plugged into the wall, the button light flashes red. When I plug the device into the computer, Verizon manager doesn't detect the device.

wobbly214 wrote:
MiFi2200 has a red flashing light and will not get a signal. When it's plugged into the wall, the button light flashes red. When I plug the device into the computer, Verizon manager doesn't detect the device.
You may have discovered by now:
"Red Blinking The battery is critically low."
Leave it plugged in for a while.
The LED can be Green, Green/Yellow which the book calls Amber, or Red.
http://support.vzw.com/clc/devices/index.html?p=5607&m=
Device Manual
Clarence

RED Blinking LIGHT

Similar Messages

Maybe you are looking for