Red led 30 second

Hello
I was happy user of Blackberry Z10 phon till last two days.Suddenly during surfing in browser apears some thiny lines on screen and phone get frozzen.I thought something went wrong and phone will restart.Phone switch off and after that I cant switch on.I tried to full charge battery so I left phone for some hours with wall socker charger, nothing happend, normally charger get warm during charging this time was cold.I press power button for 1 minute and nothing happend, volume plus/minus together also nothing.Strange thing apear when I take battery out.When battery is out and I plug phone in to wall socked red led apear for 30 seconds and then turn off.when I press power on button also red led apear with constant light (Not blinking) for 30 second.This is when acumulato is out. i bought this phone on ebay so its a bit complicated.I reed that soulution can be reinstal syste but my laptop not recognize phone,blackbery link also not recognize phone, bb swiss army knife also not recognize, what to do? Maybe is some black berry guru which have program to make reanimation for my lovely phone? please help me what to do with my phone to start work ?Maybe somebody know or have some diagnostic,developer, program which allow me to get info what is wrong with this phone and when is software help me to fiz this problem?
Sorry for bad English,I´m a bit nervous It will be nice if somebody will help me
Kind Regards
Kristof

hi Vothein
like I see on your photo phone is not connected to charger or PC and you have red led. My Z 10 just have red led when is connected to pc or to wall charger without battery inside.I don't know why it happends ??
I checked other forums and you can check another solution- charge your phone 2h then make break for 15 min and then another 2 hours.After that you press start button or plus & minus of volume on side for 15-30 second and maybe phone will start.Another option is try to update phone just via website in internet explorer,when you "Google" you can find blackberry update autoloader and then you connect your phone and after some seconds you unplug and then maybe phone run again.I used leaked version of OS, I can't find some apps in BB World and I use them to have connection with family thats why my Z 10 is dead.I stay in touch with one guy from India and he said it's hardware problem and he still dont know how to fix it.
I hope my advice maybe will be helpfull and your BB will be live again.
Best Regards
Krzychas

Similar Messages

After falling red led for 3 seconds then dead

Hi,
after falling on the floor my blackberry 8800 will not start anymore..
When I insert battery or charger cable the red led lights up for 3 seconds then turns back off but the device is dead...it the anything I can do?
Iv found other topic's talking about red flashing light and firmware reload, is this the same thing?
Thanks for any help!

Hey mau_mau,
You can try to reload your operating system but most likely all your data will be lost.
You can try to see if the device will connect to the BlackBerry Desktop Manager to back up data, but there is no guarantee it will be able to do so.
You can consult article KB11320 for instructions on how to do the load.
If you need further technical assistance, you can contact your wireless service provider.
Thanks and have a great day!
-HMthePirate
Come follow your BlackBerry Technical Team on twitter! @BlackBerryHelp
Be sure to click Kudos! for those who have helped you.Click Solution? for posts that have solved your issue(s)!

4 Red Led Lights - Please help

the other day I left my computer on for a few hours and when I came home and moved the mouse it wouldn't come out of standby. To get it to shut off, I had to hold the power button down. Now when I start it, the fans start spinning, the DVD drive spins for a second and a few times the orange light on the monitor turned green. But after about 10 seconds, it shuts down.
I have the 4 red lights on the LED, so I swapped in a new PS - Enermax 550W with 36A on the 12v. Still same thing. So I'm guessing either the CPU or the board. I built this about 6 months ago. It's not overclocked and it was idle during the time I left it. Any suggestions?

Yes and no. I know that is confussing. However go to this first as you may have had a problem right along and did not know it nor would you without testing. Memtest86 is a great way to test memory. The no part is that it could be something else. But hey you have to start somewhere.
As for the timings in RAM you need to go to Corsairs page and check the exact model on their charts. Also be sure to read any side notes as they may have specific timings for your A64 versus other CPU's. It can be different as the memory controller is on the CPU in our case instead of on the MB.
Corsair also has tech support that can walk you through memory timings if you don't follow them at all.
You can also have some other thing in the system that went bad even as simple as a HDD cable that came loose. To troubleshoot sometimes the easiest way to find out is to unplug anything that is not needed to boot.
But start with the memory as the 4 Red LED's indicate.

Red LED is on all the time

I got the problem with new phone z30.
i just had it for a week and when i turn on the phone from the first time.
there a red led on and it kept on all the time never stop.it hot really hot when i make or receive a phone call.
it burning my ear. i try all the way from reset, to turn of all the notifications off but it still on..
Can some one help ....

Reboot: On the side edge volume keys, press and hold down both of the Up and Down volume keys for about 20 seconds, ignoring the initial screenshot message... the screen will go black and reboot.
Now, if the red LED continues ON, check your Settings > App Manager and determine which of your apps is using the CPU the most, or draining the battery.
1. If any post helps you please click the below the post(s) that helped you.
2. Please resolve your thread by marking the post "Solution?" which solved it for you!
3. Install free BlackBerry Protect today for backups of contacts and data.
4. Guide to Unlocking your BlackBerry & Unlock Codes
Join our BBM Channels (Beta)
BlackBerry Support Forums Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code

Pearl Flip wont load - Red LED blinks twice, nothing on screen

My Pearl Flip refuses to load, and the only activity it shows is the red LED blinking twice every few seconds. I have tried the following
-tried reinstalling the two most recent versions of the OS using the Blackberry Desktop Software, but the installation hangs at the point of loading the system software
-tried using the application loader, however the installation hangs at loading the system software
-tried to use JL_Cmdr to wipe the device. As far as I can tell it did not wipe it (although it doesn't really provide any errors either)
EDIT: Should also say Ive tried all the above from multiple computers and using Win7 and XP
What other methods can I try to restore this device? I appreciate any suggestions that might be out there.
Thanks!
Scribs

Hey Scribs,
Welcome to the forums!
Have a look at this article for help reloading the software using loader.exe http://bbry.lv/9fsGPK If this method does not work you can try doing a reset to factory using the switch found in this article http://bbry.lv/dpNb1j
-SR
Come follow your BlackBerry Technical Team on twitter! @BlackBerryHelp
Be sure to click Kudos! for those who have helped you.Click Solution? for posts that have solved your issue(s)!

Power Mac 2.7 - Red LEDs on CPUs - Wont Start

Just finished replacing the O-Rings on my previously working 2.7Ghz Power Mac G5 and have been having a ball trying to get this thing to start again.
When I attempt to power it up, the front panel's LED lights up only when I push it and turns off immediately after I release it. After I push that, the fans spin up as they usually do, but I never hear the chime. After 2-5 seconds CPU A (The one closest to the HDDs) has an LED on its board that lights up. After 5-15 seconds (Changes each time) CPU B's LED lights up and then the machine just sits there and never goes any farther.
I have hit the PMU reset button a number of times to reset it, as well as leaving the PRAM battery out. Neither of which have helped.
The computer still does react to the plastic cover being removed as the fans spin up and the red LED comes on. I have 2 1GB Apple DDR sticks each in slot 1 of A & B.
What is the meaning of the two LEDs on the CPUs, and what could be the possible culprit of this machine no longer turning on?
Thanks in advance.

Did you replace the Thermal paste between the CPUs & Heatsinks?
LED 1—CPU A: red—contact Apple or an Apple Authorized Service Provider
LED 2—Overtemp: red—contact Apple or an Apple Authorized Service Provider
LED 3—Power On: red—the main power is on
LED 4—Trickle: yellow—Power Mac G5 is plugged into the wall correctly
LED 5—Open Firmware good: green—no problem
LED 6—CPU B: red—contact Apple or an Apple Authorized Service Provider
LED 7—Checkstop: red—contact Apple or an Apple Authorized Service Provider

Q10 wont turn on. Red LED 1101111 blinking.

Hi All,
Just updated my Q10 to 10.3 via the carrier update and after half a day my phone turned off and now it wont turn back on again.
When I press the power button the yellow LED comes on and after that the red LED blinks in the following sequence 1101111.
Tried all the usual tricks. Battery pull, plugged phone in without battery, plugged into blackberry link, used original charger/cable, hold power button down for 10 seconds etc...All don't work.
Any ideas would be much appriciated

Hi and Welcome to the Community!
I cannot quite tell if you have done exactly this or not...apologies in advance if you have. Please try this sequence...note that, throughout the entire 4h15m process, your BB must remain directly connected to a known-good wall charger (not PC USB, not a cradle):
With the battery inside, connect your BB to the wall charger
Leave it alone for 2 hours, no matter what the LED or the display does
Remove the battery
Wait 15 minutes
Insert the battery
Wait another 2 hours, no matter what the LED or the display does
This has been known to "kick start" some BBs. If it fails, please try again but increase the wait time in step 4 to 2 hours, and perhaps as long as 4-5 hours.
It is also possible that your battery or BB has experienced a problem...to test, this sequence is needed:
Obtain an known good and already fully charged additional battery...use it in your BB and see what happens
Obtain access to a known good and identical BB...use your battery in it and see what happens
The results of this will indicate if it's your BB or your battery that has the problem. Note carefully please that "new" and "know good" are not necessarily the same things. While rare, a "new" battery certainly could be defective. Rather, the simplest (and least costly, btw) method to conduct this test is to find someone with an identical BB who has no issues...trade batteries and see what happens.
It is also possible that the OS update caused this. Due to the number of problems with "upgrading" to this OS level, I suggest you try the very clean and very forceful AutoLoader OS Reload:
http://supportforums.blackberry.com/t5/BlackBerry-10-OS-Device-Software/Upgrading-OS10-devices-using...
Beware that it is completely destructive...the device will be "like new"...no data, no apps, no accounts, etc. Be sure you take a full backup first, as well as make full manual documentation of all apps, accounts, configurations, etc. Sometimes a restore reintroduces the very corruption one is trying to eliminate, and manual reconfiguration is necessary.
You can also use this to fall back to a prior OS if you desire...you can install any OS level for which you can find an AutoLoader. (Hint...search over on the CB site!)
Good luck and let us know!
Occam's Razor nearly always applies when troubleshooting technology issues!
If anyone has been helpful to you, please show your appreciation by clicking the button inside of their post. Please click here and read, along with the threads to which it links, for helpful information to guide you as you proceed. I always recommend that you treat your BlackBerry like any other computing device, including using a regular backup schedule...click here for an article with instructions.
Join our BBM Channels
BSCF General Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code

Luna BH-220 Flashing red led for hours

I just received my two Luna head sets. The first one charged up fine and did the NFC pair no problem, but the second unit seems to be having a problem.
The second one just flashes the red led when it is in the cradle. The Led on the cradle is green. The red led on the ear piece turns off if I remove the charger, but just returns to flashing when I plug it back in. This has gone on for the past 5 hours. How do I get this unit reset? What does the flashing LED mean? Both units had very sparse information in the box and I can not find the user manual anywhere on the Nokia support site. The Luna isn't even listed in the support accesories section. Maybe it's too new??.
Solved!
Go to Solution.

UPDATE: finally managed to get nokia to return my THIRD broken nokia bh-220 bluetooth device, as I purchased it from amazon.
Filled out the necessary online form and sent it to FONEBIZ for the repair (authorised nokia repairs).
Two days later, I receive a phone call saying that the device is NOT covered and I am to pay a whopping $170 for them to REPLACE my green device for a BLACK ONE. (See attached photo for proof). Please bare in mind that I only paid $57 for my green nokia luna BRAND NEW. So where FONEBIZ get thier estimate from is simply outrageous.
When I contacted Nokia, they said their customer service represented was wrong, and she shouldn't have given me the details to return the item. Once again NOKIA, WHERE ARE YOUR BRAINS HERE.?
NOTE
DO NOT BUY NOKIA PRODUCTS PERIOD
DO NOT RETURN ITEMS TO FONEBIZ THEY WILL SIMPLY RIP YOU OFF, AND ARE CLEARLY INCOMPETENT AT REPAIRING BLUETOOTH DEVICES. SO I WOULDN'T EVEN ATTEMPT TO LET THEM REPAIR A PHONE.
NEVER EVER AGAIN WILL ME OR MY FAMILY PURCHASE A NOKIA PRODUCT. I AM DISGUSTED WITH THEM.
And I encourage, whoever is reading this, to just acknowledge she sheer hell I've been through just for a simple cheap bluetooth device, and just make sure your aware of the risk when buying a more expensive product. Nokia didn't give a second thought to my bad luck. Why would they treat you any different.
WE ARE JUST MONEY TO THEM...
Attachments:
image.jpg ‏56 KB

2008 Mac Pro-Red LED on motherboard = ?? (not diagnostic LEDs)

My 2008 Mac Pro looks like it's on it's way out to pasture. (Again.)
So, last year I put a new PSU into my 2008 Mac Pro. Worked great and kicked it right back into gear. Temporarily. Now it's behaving almost the same—erratically. It won't boot. It may chime, may not, but either way it's going to "click" and turn off within 4-5 seconds of pushing the power button. THEN, re-pushing the power button makes it behave like it's fully dead—like it's not even plugged in. This is exactly how it behaved when the PSU died before.
But, HERE's the question... that no one seems to be able to answer: There is a red LED on the motherboard. It is NOT the set of diagnostic LEDs behind the RAM cage. This little light is almost under HD Bay #1, to the left of the BT card spot and the airport card. This LED stays lit red at all times now.
What does this red light mean?
Here's a thread that proposes that it is related to electric malfunctions. But there was never a confirmation of exactly what this specific light signifies.
If you can't picture where this light is, there are pictures in the above, linked, MacRumors forum thread.
Any input would be appreciated. These lights are mentioned nowhere in the service manuals that I've seen. Last time I was able to run the Apple Hardware Test, it said, "no problems found". Memtest says all is well. Reseating the cards does not remedy the issue. What is this mystery light telling me?

Here's a picture of the led in question.

MSI KT4AV 4 RED LEDs WON'T BOOT

Hi. I recently purchased a new MSI KT4AV motherboard, new AMD Athlon 1.33 Ghz CPU, and new PC2100/DDR266 DIMM RAM, and when I turn it on, all 4 LEDs on the diagnostic bracket light up RED (meaning processor failure). Does anyone know what could cause this?
My system specs:
MSI KT4AV motherboard
AMD Athlon 1.33 Ghz 200 FSB CPU
PC2100/DDR266 DIMM
420W PSU (+3.3/28A, +5/40A, +12/18A)
Hopefully that's enough to diagnose any problems because it won't output any video, just 4 red LEDs on the D-bracket.
Thanks.

Hello,
When I bought my second KT4AV, I was planning on using an Athlon T-Bird 1.4 I had laying around in it. It had the exact same problem as you are having, it just didn't work. I then tried a Palomino 1700+ I had in a another computer that I knew worked fine - it was (and still is) in a K7T266 Pro2-RU - and it didn't work either.
I was thinking the motherboard was bad but I bought an Applebred Duron 1600, and it worked perfectly! So it would seem that even though they are listed as compatible, the older Athlon T-Birds and Palominos simply will not work. My advice to you, buy an Applebred Duron, or better yet, an T-Bred XP 2000+.
Sorry if that wasn't what you wanted to hear!
-James

PM8M-V no beep no boot Solid Red LED

I've had the PC I've been using for about 2.5 years, no problems.
Last week a lightning storm killed all the AGP/PCI functionality of my old motherboard. At first, I thought it killed my AGP video card because the internal video to the old motherboard worked fine. This is where I decided to buy an MSI PM8M-V from CompUSA.
Tried installing the board today. I literally just powered down the PC with the OLD Board in it and it all was working fine. The two motherboards seem to be similar in quality and both have internal sound and video.
With the new motherboard hooked up when I press Power the CPU fan comes on, and the LEDS on the front of the tower come on. The RED LED [Which I believe is the HDD LED, will have to double check] comes on and stays lit. After about 20 seconds or so the system powers down. I get no beeps or anything. I doubt any of the components are bad because they were all just working 1 hour ago.
Does this point to a specific problem? I don't think the CPU is overheated as I have thermal paste the Heatsink fits snug.
Suggestions?

Ok, an update.
I have an Antec PSU 300W that appears to be working well.
At the moment I have 1gig of unknown brand DDR memory
I have a P4 Prescott 3.0GHz [I don't recall any of the other details as this PC is several years old]
All hardware pulled from a perfectly working system with the exception of an AGP slot on the old motherboard.
The old motherboard has nearly the exact same features and appears to be of very comparable quality.
I hooked the old motherboard up with the processor, memory, and same PSU and it booted to the BIOS just fine.
This new MSI motherboard WILL NOT boot to the BIOS with the exact same equipment installed. I have double and triple checked.
Is there anything else I should do before contacting CompUSA for a return. I've seen some recommendations about jumping pins to clear the CMOS or something.

K8N Neo2 4 Red LEDs system boots fine except...Please Help

Just installed a K8N with new AMD Athlon 64 3000+ with factory heatsink and fan. Everything boots up fine except that I have 4 Red LEDs. I am using a 450W power supply...its a powerlab brand (didnt cost very much) but has high voltages, windows seems to be running fine. Programs run and install etc. So according to the LED guide the cpu is installed incorrectly...if that was true wouldn't it not run correctly. If I need to reinstall heatsink how do I go about that since there was a thermal coating on the heatsink already.
Additonally:
1. whenever I do an audio test the right channel plays out the left speaker and vice versa.
2. When I try to boot with a second HD it locks up during the splash screen. I messed around with jumpers and nothing seemed to work.
This is my first system build
Please Help

Let me answer the last, first. Yes you can get different RAM that will perform differently. However not all more Expensive RAM will be faster or more stable. I know some of that does not make the sense you would think but remember that the A64 likes cheapy RAM in a lot of cases better than Uber RAM.
OK back to timings. If you test Bandwidth with say SiSoft Sandra you will see that changing from 3,3,8 top say 4,4,8 will hardly affect the performance. Manybe more so it would affect you if you had the system cranked to max overclock. However even then if would not be anything you will notice say running a game or even in other benchmarks. We went through the same issues with the Via boards and I think you will be suprised with the results. In my case going from 4,3,8 to 4,4,8 dropped my Sandra results from 3031 to 3029. You can even determine that amount of difference and in fact that is within the margin of error for the test.
OK so I still say try it and see if the system runs better. Oh and back to the other question for a moment. When we compaired my cheapie RAM in the Via section to some nice Uber Expensive RAM we saw almost identical results ranginging from 3020-3050 at stock speeds. So unless you are planning to really overclock heavy you likely won't see any difference between $80 per 512MB stick and $150 512MB sticks.
Some food for thought. We tested, you decide.

No post! 4 Red LEDS on Dbracket! K8N Neo Platinum.

I put together a brand new computer back in August with the K8N Neo Platinum as my motherboard. Here's a list of my components.
Athlon64 3000+
1GB OCZ 3500 DDR
Sapphire 9800 Pro Radeon
160GB Seagate SATA drive
NEC DVD-RW
ComproPVR TV tuner
Vantec 400W PS
Anyway, the computer worked great until just after Hurricane Ivan came through. After our power came back on, the computer booted a couple of times, and then for no reason started giving me problems.
The computer would start up for about 3 to 5 seconds with 4 red LEDs appearing on the Dbracket. Then power would then shut off automatically. I have not changed any hardware or software. I do not believe it is PS related, as I have tried my current one in another computer without problems. Also, I doubt the processor is faulty. I can't think of a reason it would just stop working. Please let me know if you've experienced anything similar and if you know of a solution.

probably a powerspike during the hurricane killed or almost killed a part of the pc, and it completely died right after.
you could have a pc store test the mobo, cpu and sorts....

BlackBerry Z10 won't turn on and red led blinks 4 times

Hi all,
Yesterday my BlackBerry Z10 suddently turned off, I turned it on again and it worked fine for a few minutes (battery was around 90% full), then it turned off again and I couldn't turn it on anymore! The red led is blinking 4 times with a 3 seconds interval between each 4 blinks sequence. I tried to charge the battery, connect it to the computer, turn it on without the battery (with charger on), with no success. Sometimes, it shows the BlackBerry logo, or even the logo with the % loading, but then it turns off in the middle of the process, on random percentages.
Does anyone know what happened to the phone and how to solve this issue?
Thanks!
V

Mine keeps turning off... I called them and they told me to send the phone to Blackberry by mail to check what's wrong and that when the phone gets there, they do a complete evaluation and in 30 days they send the phone back... In other words, I have to buy another phone! Blackberry assistance is useless...

Business Process Engine is showing Red Led in RWB

Hello to All, I installed PI7.1 and after client copy - Business Process Engine is showing Red Led in RWB.
When I click on BPE, the message at bottom of screen (in Yellow Status) indicates " Schedule background job for clearing report". Please let me know if any one has the solution with details.
I gone thru the link in SDN, but no resolution yet.
Re: Business Process Engine is showing Red Led in RWB
thanks, Srini

Hi Mark, All the nodes are green under "Maintain Runtime Environment" and "Maintain Definition Environment".
In RWB, component monitoring --> Display -- Business process engine is RED with message as
"Schedule background job for clearing report" in Yellow.
I looked under batch jobs "SWWCLEAR" and it is already ran successfully.
Please let me know how can i make BPE green.
thanks, Srini
Edited by: Srinivas Chatrati on Apr 20, 2009 11:51 PM

Red led 30 second

Similar Messages

Maybe you are looking for