Red Led Light

Hi, I have bought this laptop which is fairly new, just under a year. Although now, there is an red Led light on the side of my laptop when I plug in my Ac Adaptor to charge the battery and it is not going. The Led Light was always a bright white light but now it just stays red and I dont know why? Is there a problem with my laptop? because it is working fine. I dont know how to solve the red led light or what it means. I hope I can get some information about this. Thank You.

jpdvid-
Did you try starting the Mac back up after installing the RAM and before installing the card? Many times a PMU reset is needed after RAM is installed.
Which model of Rocket Raid card are you installing?
Luck-
-DaddyPaycheck

Similar Messages

Turn red LED light off

Is there an option or registry edit that will turn off the red led light that dots the "i" in ThinkPad on the top of the laptop? I have a SL500.

Hi adoman,
I suggest putting following sticker on it, you'll never notice it's there:- http://cgi.ebay.com/Original-IBM-Lenovo-Sticker-11-x-30mm-127_W0QQitemZ350223067619QQcmdZViewItemQQp...
Hope it helps.
Maliha (I don't work for lenovo)
ThinkPads:- T400[Win 7], T60[Win 7], IBM 240[Win XP]
IdeaPad: U350
Apple:- Macbook Air [Snow Leopard]
Did someone help you today? Compliment them with a Kudos!
Was your question answered today? Mark it as an Accepted Solution!
Lenovo Deutsche Community Lenovo Comunidad en Español
Visit my YouTube Channel

My bb curve 9380 shutdown and a red led lighting

my bb curve 9380 shutdown and a red led lighting i don't now what hapned but i just modify some apps bay bb desktop softwere please help me and thx verry much

Hi and Welcome to the Community!
Please try this sequence...note that, throughout the entire 4h15m process, your BB must remain connected to a known-good wall charger (not PC USB):
With the battery inside, connect your BB to the wall charger
Leave it alone for 2 hours, no matter what the LED or the display does
Remove the battery
Wait 15 minutes
Insert the battery
Wait another 2 hours, no matter what the LED or the display does
This has been known to "kick start" some BBs.
It is also possible that your battery or BB has experienced a problem...to test, this sequence is needed:
Obtain an known good and already fully charged additional battery...use it in your BB and see what happens
Obtain access to a known good and identical BB...use your battery in it and see what happens
The results of this will indicate if it's your BB or your battery that has the problem.
If the problem is revealed via the above tests to be your BB, then I recommend that you attempt to boot into Safe Mode:
KB17877 How to start a BlackBerry smartphone in Safe Mode
It may take you multiple attempts to get the ESC key sequence (press/release/hold) correct, so be patient. When successfully into Safe Mode, see what happens.
If the behavior ceases, then think carefully...what happened just before this behavior started? A new app? An update? A Theme? Something else? Think carefully as the smallest change could be causal...and attempt to undo whatever that was.
But if the behavior continues in Safe Mode, then you may need to consider more drastic actions -- WIPE, OS Reload, BBSAK Wipe/Reload, and the "Bare Bones" OS Reload Process. To prepare, you should be sure that you have a full backup to your PC...please review the Backup link in my auto-sig on this post for instructions.
You may also need the use of these tricks:
KB10144 How to force the detection of the BlackBerry smartphone using Application Loader
KB27956 How to recover a BlackBerry smartphone from any state
http://crackberry.com/blackberry-101-lecture-12-how-reload-operating-system-nuked-blackberry
Good luck and let us know!
Occam's Razor nearly always applies when troubleshooting technology issues!
If anyone has been helpful to you, please show your appreciation by clicking the button inside of their post. Please click here and read, along with the threads to which it links, for helpful information to guide you as you proceed. I always recommend that you treat your BlackBerry like any other computing device, including using a regular backup schedule...click here for an article with instructions.
Join our BBM Channels
BSCF General Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code

BlackBerry Z3 does not Boot, red LED Light is flashing 1x long and after 6x short

After updating my Blackbery Z3 to 10.3.1.1779, my device won't boot and  red LED Light is flashing 1x long and after 6x short. Need help to solve the issue. Thanks in advance.

Thank you for your update.
1. If any post helps you please click the below the post(s) that helped you.
2. Please resolve your thread by marking the post "Solution?" which solved it for you!
3. Install free BlackBerry Protect today for backups of contacts and data.
4. Guide to Unlocking your BlackBerry & Unlock Codes
Join our BBM Channels (Beta)
BlackBerry Support Forums Channel
PIN: C0001B7B4   Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA   Display/Scan Bar Code

Red LED Light Remains On

The battery is fully charged and disconnected from charger. When hibernating, the red LED light constantly remains on. When the phone is being used, the red LED light does not appear.
What is wrong? How can this be fixed? Thanks much for help.

I'm a total newbie to smartphones. Based on your question, I cleared all the Notifications and the red LED disappeared. Then sent myself an email to test the blue LED light and it is now blinking. So, the problem might be solved but don;t know why the red LED constantly displayed after charging the battering to 100%.
Don't know about Lightflow!
Thanks

HELP! BB Pearl 8130. Solid Red Led Light. Won't go away.. HELP!

My LED has turned a solid Red color. It's on all the time and is only off when I pull the battery out. My phone does still charge. I've done everything to get rid of it even wiping my blackberry and upgrading the software. I read something about Blackberry Music Gateway? I do use my pearl to listen to Pandora everyday and iheart radio with a 3.5 cable that plugs into the dash of my truck, but it never did this before. Any help would be greatly appreciated!
Thanks!
Justin

Justin, so you've wiped the device completely and reloaded a new OS... still does the same. Anytime the BlackBerry is powerd on, the LED lights up RED?
1. If any post helps you please click the below the post(s) that helped you.
2. Please resolve your thread by marking the post "Solution?" which solved it for you!
3. Install free BlackBerry Protect today for backups of contacts and data.
4. Guide to Unlocking your BlackBerry & Unlock Codes
Join our BBM Channels (Beta)
BlackBerry Support Forums Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code

Mysterious red LED light inside my G4

Could someone tell me what the red light means on the inside of my G4?
It can't be seen from the outside.
I am having a problem with my firewire ports not working. Is this a warning or alert of some kind?
Help! I really looked and can't find this info anywhere!

From the G4 Service Manual:
Logic Board LEDs: Power Mac G4 (AGP Graphics)
There is one red LED on the Power Mac G4 (AGP Graphics) logic
board. It indicates that there is power to the board and does not imply a fault condition. Hardware such as DIMMs and PCI cards should not be installed or removed when the LED is on.
Cheers, Tom

4 Red Led Lights - Please help

the other day I left my computer on for a few hours and when I came home and moved the mouse it wouldn't come out of standby. To get it to shut off, I had to hold the power button down. Now when I start it, the fans start spinning, the DVD drive spins for a second and a few times the orange light on the monitor turned green. But after about 10 seconds, it shuts down.
I have the 4 red lights on the LED, so I swapped in a new PS - Enermax 550W with 36A on the 12v. Still same thing. So I'm guessing either the CPU or the board. I built this about 6 months ago. It's not overclocked and it was idle during the time I left it. Any suggestions?

Yes and no. I know that is confussing. However go to this first as you may have had a problem right along and did not know it nor would you without testing. Memtest86 is a great way to test memory. The no part is that it could be something else. But hey you have to start somewhere.
As for the timings in RAM you need to go to Corsairs page and check the exact model on their charts. Also be sure to read any side notes as they may have specific timings for your A64 versus other CPU's. It can be different as the memory controller is on the CPU in our case instead of on the MB.
Corsair also has tech support that can walk you through memory timings if you don't follow them at all.
You can also have some other thing in the system that went bad even as simple as a HDD cable that came loose. To troubleshoot sometimes the easiest way to find out is to unplug anything that is not needed to boot.
But start with the memory as the 4 Red LED's indicate.

Playbook will not charge, no red LED light

The Battery charge said 3%. I turned off the playbook and plugged it in and left it to charge with the LED lights showing. I went to retrieve it, only to find out it's not turning on. No red light appeared. nothing. I went and plugged it in and then tried turning it on Nothing.No red light...just dead. PS: I just got the Playbook from relative without the manual and all so i'm not sure about the DO's and DON"T's of using the tablet. Please help!!! Thanks in Advance.

Your battery is dead. http://www.blackberry.com/btsc/KB27705
Try this:
Connect the charger that came with the PlayBook and plug it into the wall. Hold down the Power Button only for 20 seconds. Leave it for 4 minutes, then unplug at the wall, wait a minute, plug it back in again, hold down the Power Button only for 20 seconds.
Repeat this process about 10 times and hopefully, your PlayBook should go into a high charging rate. Leave it plugged in overnight and you should have a full charge by morning.
1. Please thank those who help you by clicking the "Like" button at the bottom of the post that helped you.
2. If your issue has been solved, please resolve it by marking the post "Solution?" which solved it for you!

BlackBerry Curve 9380 will not power ON and the red LED light is flashing

I need you guy's help. I was charging my BlackBerry Curve 9380 this morning. When I was about to use it the found out that the screen will not light up but the red led indicator is blinking one long blink, one ong blink then a full stop. I have already tried removing the battery and sim card for sometime but to no avail. What should I do?!

You need to consider updating/reinstalling device OS. Check the below knowledge base article -
KB03621 How to clean reload BlackBerry Device software and applications using BlackBerry Desktop Software
tanzim
If your query is resolved then please click on “Accept as Solution”
Click on the LIKE on the bottom right if the post deserves credit

Sony Xperia M2 flashing Red LED light and wont turn on.

Okay so i have been having this problem for about a week.I tried turning on my phone the other day but it wasnt doing that so i thought maybe it ran out of battery then i let i charge for a couple of hours and left it untouched.When i came back my phone was flashing a red light and the sony logo would apear and my phone would vibrate but then it would shut down again.This has been happening for all week i let it charge overnight but still the same thing happens flashing red and vibrating.Sometimes the light dosent flash and i can turn my phone on for a while but i never know when it could randomly shut down.i tried using the Pc companion program to try and fix it but my phone wont stay on for long enough for it to be able to do that.Any tips on what i could do ? the last thing i wanna do right now is call sony so please if you know any possible way of fixing this let me know

Hi and welcome to the community! Since you're new please be sure that you have checked out our Discussion guidelines.
Have you tried to power on the phone without SIM- and/or SD-card to see if this can help? Otherwise, a software repair via PC Companion would be recommeded:
http://support.sonymobile.com/global-en/tools/pc-companion/
In PC Companion you press start on Support Zone > Start on Update the phone/tablet software > Repair phone/tablet (the blue clickable link in the message) > Follow these steps without having your device connected to the PC.
Follow the instruction that appears in the program and do not connect your device until this guide tells you how to connect it. When you are going to connect the phone, the phone should be completely off. Hold the ON/OFF button + volume up(+) for 10 seconds.

Aironet 1242 seems dead - just a light red led status

Hello,
For an Aironet 1242 who's no more covered with a SMARTnet contract.
Symptoms are the same whatever power-injector, power supply or via PoE switch.
Just one led.
A permanent red led (light red) on the status, nothing else.
No reaction on the console port.
Is that device dead ?

Hi
With symptoms looks like device is dead and needs to be replaced.
Regards,
Akash

After falling red led for 3 seconds then dead

Hi,
after falling on the floor my blackberry 8800 will not start anymore..
When I insert battery or charger cable the red led lights up for 3 seconds then turns back off but the device is dead...it the anything I can do?
Iv found other topic's talking about red flashing light and firmware reload, is this the same thing?
Thanks for any help!

Hey mau_mau,
You can try to reload your operating system but most likely all your data will be lost.
You can try to see if the device will connect to the BlackBerry Desktop Manager to back up data, but there is no guarantee it will be able to do so.
You can consult article KB11320 for instructions on how to do the load.
If you need further technical assistance, you can contact your wireless service provider.
Thanks and have a great day!
-HMthePirate
Come follow your BlackBerry Technical Team on twitter! @BlackBerryHelp
Be sure to click Kudos! for those who have helped you.Click Solution? for posts that have solved your issue(s)!

HELP Needed ASAP! Curve Not Turning On, Red Flashing Lights!

Hi,
I have a Blackberry curve 8310. I plugged my curve into my mac to do a software update. Midway through, my phone shut off and hasn't worked since. The battery is fully charged. The phone is off and won't turn on. Additionally, there is a red LED light blinking twice every few seconds. I think I found an article on blackberry.com's knowledge database that diagnosed my issue, but my problem now is that because the curve isn't turning on/off, it's not connecting to my mac's desktop manager. So I can't do anything the article tells me to do. What should I do now? I need help ASAP!
Here's the link to the article: http://www.blackberry.com/btsc/search.do?cmd=displayKC&docType=kc&externalId=KB19915
Thanks in advanced!

Hello Asmro and welcome to the BlackBerry Support Community Forums.
It can take up to 30 minutes for the Mac to connect to the BlackBerry.
I would remove your battery and connect to the BlackBerry Desktop Manager. Once it comes up there is no software installed, re-insert the battery and follow the article KB19915.
Let me know how you make out.
-HMthePirate
Come follow your BlackBerry Technical Team on twitter! @BlackBerryHelp
Be sure to click Kudos! for those who have helped you.Click Solution? for posts that have solved your issue(s)!

K8N NEO Platinum 4 Red LED at Startup

I installed a new MSI K8N Neo Platinum mainboard in my computer in December 2005, and my computer has been a pain ever since. My problem is 85% of the time when I turn the power on it just won't boot up, I get 4 Red LED lights. If I shut it off and on half a dozen to 20 times. During one of those times it will bootup normal and work great. Shutdowns are normal.
My Family hates this and won't use it. This computer has been nicknamed the MSI Little Witch. I have had it down to barebones out of case with just graphic card, 1 memory stick, IDE harddrive, keyboard and mouse, it will do same thing. I've unplugged and replugged everything countless times. It still does it. I have tried Maxtor, Samsung, and Western Digital hard drives with fresh install of Windows XP Pro, it still does same thing. I have alternated memory sticks, same thing. It will warm reboot as long as I don't powerdown, but if I shut the power off it will not reboot until it cools down about 20 minutes. Then I can go through the same startup problems as I normally have. I have not done any overclocking.
Anyone have a fix to this fustrating problem?

I have the same problem with my K8N Neo Platinum. Except mine seems to occur after the motherboard has not had power after sometime. For example, it happened every time I moved my computer when I moved into and out of my dorm room. I don't know if its the same "cooling down" time you're talking about, but what usually fixes it for me (at least temporarily) is killing the power to the machine while it is on. Regular soft resets won't work for many tries, but when the computer is on with all 4 red LEDs i'll flip the power switch on the power supply. That usually makes it work fine. Also another thing that seemed to intermittently trigger it is changes to the BIOS. A CMOS reset would not fix that either. I would have to flip the power switch and kill the power. Then after starting it
up again it would be okay. I have also tried multiple combinations of different cpus, memory sticks, and video cards. I also made sure there were no shorts to ground anywhere.
Also after a year of solid operation (with the exception of this problem) I started to get Machine Check Exception BSODs in XP. I think this was because of a possible bad stick of RAM, because that seemed to cause lockups in the way beginning of the Windows setup (where it is loading files such as Windows Executive, etc). When I removed it and put another stick in, the windows installation would go fine. But, that did not fix the issue with this motherboard.
I've had so many problems with the multiple K8N Neo Platinums I have purchased. This is absolutely ridiculous I'm extremely POed at MSI for the widespread K8N series problems. I am usually very tolerant to companies when they have problems with products because I understand that problems and glitches can easily occur in mass production and design. It is virtually impossible to make a "perfect" product from the start. But the lack of response and concern from MSI about this is ridiculous. MSI did make an excellent motherboard here--if you can get a working one.

Red Led Light

Similar Messages

Maybe you are looking for