Redner settings help

I am using CS5 Production premium. I am having difficulites with render settings in Media encoder. When I select a .mov source clip and input settings to export to .wmv format the videos do not play back properly on Windows XP with any version of WIndows Media player. The closet I have gotten is the audio will playback but the video does not. The .wmv will play back fine on my Windows 7 64-bit machine running WMP 12.
However when I import the clips into After Effects and then render them with the same settings I used in Media Encoder the exported files do play back on Windows XP I have tested with WMP version as low as version 9. I thought that the other Adobe Apps would be using Media Encoder on the back end when exporting clips.
Format:     Windows Media
Preset:     NTSC Source to Download 512KBPS (rest of the settings are the defaults for this option)
Codec:     Windows Media Video 9 (I have tried each option in Media encoder)

WMP uses hardware acceleration, so more than anything else it is probably simply the inadequacy of the hardware or unsuitable settings on your XP machine. Could be anything from just a slow drive (unlikely) to misconfigured graphics (more likely) to the WMP pref for hardware accle itself. Also make sure that third-party players do not bust up your WM stuff. In case of doubt, simnply reinstall Windows Media Redistributable from the MS pages.
Mylenium

Similar Messages

My ipod screen wont slide to unlock and i have just reset it to factory settings, help!

my ipod screen wont slide to unlock and i have just reset it to factory settings, help!

Seems like a hardware problem. An appointment at the Genius Bar of an Apple store is in order.

I phone 5c settings help.

help!i phone 5c settings help. upon opening phone shows enlarged keypad for my pass code, but is difficult to type on. how to get my numbers and home screen back to normal.

On the Home screen, double-tap with three fingers to exit zoom.
Then, after you have entered your Passcode...
go to Settings > General > Accessibility and make sure Zoom is turned Off.
More Info here > http://support.apple.com/kb/ts3129

Your call cannot be connected pls. check your phone settings help plsss

your call cannot be connected pls. check your phone settings help plsss

mhayo wrote:
your call cannot be connected pls. check your phone settings help plsss
Check the Telephone Number you are calling...
Contact your Carrier.
Also...
Try This...
Close All Open Apps... Perform a Reset... Try again...
Reset ( No Data will be Lost )
Press and hold the Sleep/Wake button and the Home button at the same time for at least ten seconds, until the Apple logo appears. Release the Buttons.
http://support.apple.com/kb/ht1430

How do i get sound from macbook internal speakers? need sound settings help

hi,
i have installed service pack 3 on bootcamp on new macbook.
i cant get any sound with all my audio applications, even windows media player. i can see the levels and audio files playing within the software (soundforge, wavelab, cubase etc) but cant get any sound to come out the macbook internal speakers........
ive tried all the available audio driver settings from within the apps.
ive checked the sound controls menu from my system tray...all the volume faders are full, unmuted.
theres a realteck or something like that, control panel......i think realtek is the internal sound funtion of my windows xp......
anyone help?
(ive updated bootamp to 2.1 with software updater..... ive intalled the bootcamp drivers from my leopard install dvd....)
shall i put the leopard dvd in again? in case the bootcamp drivers never got installed????
i just used the first leopard dvd.........should we also use the 2nd leopard dvd????? bootcamp manual just says put leopard dvd in and install bootcamp drivers.........but it dont say which leopard dvd.........
cheers
i understand latency is gonna be an issue with internal sound drivers.....any one recommend third party sound drivers for use with internal macbook?
(for proper work im gonna use a proper external soundcard with ASIO drivers, but i wanna get half decent sound and latency from macbook internally for when i wanna use JUST the laptop, with no units connected)

dude..... i cant answer that.....cause i dont know....... im pretty sure i didnt do anything.....sound just started working..........
ive done so much over the past few weeks.....its all a blur......
seem to recall changing windows sound settings to NO SOUND to get those irritating beeps to go away..... thats all i can remember......
anyway its working.....mac internal sound is working.....and also i have found a gooooood driver to use.....to lower latency...... its called asio4all...... its the best driver i have used in cubase on bootcamp...... goooooood latency figs...sounds nice too.......
guess what? ive also had my first crash since i bought the mac......on windows xp////sdffdjojfnds
ararrrrrrrrrrrghhhhhhhhhhhhhhhh

Final Cut Exporting to DVD Settings Help!

Hello, all. Hopefully someone can help me with this problem that I have been struggling with for weeks.
I shot a video project in standard definition on a Sony VX2000, then edited it in Final Cut Express. I am now wondering what the best export settings would be in order to put it onto a DVD, and maintain the quality at 100 percent. I've tried exporting it in several different ways, but no matter what I do, the quality is never as good as it was shot.
So, what should the export settings be from Final Cut? And do you think I need to use a different software to maintain perfect quality on a DVD?
Thanks so much

You need to ask this question on the FCE forum
Final Cut Express HD

Application Server Data Source settings help needed (10.1.2.0.2)

Hi,
Can someone tell me what maximum values can I set in the following properties under Connection Attributes when I define a DataSource on
Application Server. I have almost 25+ web application deployed on my 10.1.2.0.2 server that all uses one data source I have defined. Now the issue is the number of requests
are very high and every now and then I get timeout error when trying to get the database connection. At one particular instance at peak time I may get over 200+ requests that
do some databse connections etc. Following are my current settings. But need to increase some more but wondering what are the maximum values I can have. I have only one server 10.1.2.0.2
Connection Retry Interval (seconds) = 5
Max Connection Attempts = 3
Cached Connection Inactivity Timeout (seconds) = 30
Maximum Open Connections = 60
Minimum Open Connections = 10
Wait For Free Connection Timeout (seconds) = 15
What other properties can I have to make use of datasource effectively.
Thanks

Here is the copy of my datasources.xml.
<?xml version = '1.0' standalone = 'yes'?>
<!DOCTYPE data-sources PUBLIC "Orion data-sources" "http://xmlns.oracle.com/ias/dtds/data-sources-9_04.dtd">
<data-sources>

<data-source class="com.evermind.sql.DriverManagerDataSource" name="OracleDS"
               location="jdbc/OracleCoreDS" xa-location="jdbc/xa/OracleXADS"
               ejb-location="jdbc/OracleDS"
               connection-driver="oracle.jdbc.driver.OracleDriver"
               username="scott" password="tiger"
               url="jdbc:oracle:thin:@//localhost:1521/oracle.regress.rdbms.dev.us.oracle.com"
               inactivity-timeout="30"/>

<data-source location="jdbc/TestDS"
               class="com.microsoft.jdbcx.sqlserver.SQLServerDataSource"
               password="pwd" xa-location="jdbc/TestDS"
               ejb-location="jdbc/TestDS"
               connection-driver="com.microsoft.jdbc.sqlserver.SQLServerDriver"
               username="usr"
               url="jdbc:microsoft:sqlserver://someloc99:1433/DevelopmentAp"
               inactivity-timeout="30" name="jdbc/TestDS"
               connection-retry-interval="5" max-connections="50"
               max-connect-attempts="3">
    <description>jdbc/TestDS</description>
    <property name="DatabaseName" value="DevelopmentAp"/>
    <property name="serverName" value="someloc99"/>
</data-source>
</data-sources>I also tried changing max-connections="0" it did helped but still after sometime I get timeout while connecting to the database. Don't know if it's with SQL Server that is not letting that many concurrent connections/sessions or something on the Application Server side.
Thanks
Message was edited by:
WhiteSox
Message was edited by:
WhiteSox

Reset button not visible in settings, help?

Reset button and security button not visible in general settings on my iphone 4 . How do I restore them?

if you use the off-line version, Formscentral AIR Application, help menu will bring you to the help page. For example: DE http://help.adobe.com/de_DE/formscentral/using/index.html

Problem with resseting to factory settings HELP!! ...

hi im having trouble resseting to factory settings. when i enter my lock code it says lock code entered incorrectly 5 times. code will unblock in 5 minutes. what does this mean can anyone help..

It means exactly what it says.
You have entered the code wrong five times so for the next five minutes it will not let you try again. After five minutes it will let you try again.
If you cannot remember your code after further attempts then you will need to visit a nokia care point to get the code reset.
Care points/service centres and repair info:
UK • Europe • Asia-Pacific • USA •
Canada • Middle East and Africa
Elsewhere: Click here, select your country, go to the support section, then select repair.

Sony Vaio Laptop return to factory settings HELP

I have a Sony Vaio laptop that i bought 5 years ago. It is very slow and takes a while to get into the swing of things and I want it to run better, So I have a 1TB external hard drive and I was going to back up all the important files and restore it to factory settings, BUT... I dont have a disc with windows on or anything like that. So I've found that I can do a recovery partition. Will I be ok to do this without having Windows on disc etc etc? Would this help the laptop run faster and "be like new" ?

Hi ltc58!
Thank you for considering Sony Community!
Since your laptop is quite old and you're experiencing slow performance, performing a Full Format Recovery would be the best option, as long as the recovery partition of the unit is still intact and not corrupted. Yes, you can still try to format the computer. Please make sure to backup all of your important files on your external drive. The laptop will reinstall the Operating System and it will go back to its original factory settings.
Please follow one of these steps:
Using Assist Button: Shutdown the laptop and remove all peripherals except for AC adapter. Press Assist button. Select Start Recovery Wizard -> skip Rescue -> Start recovery.
Using F10 key: Shutdown the laptop and remove all peripherals except for AC adapter. Turn on the unit then immediately, keep tapping F10 key.
NOTES:
*If an Edit Boot Options screen appears, press the Enter key.
*If a Windows Boot Manager screen appears, select VAIO Recovery Environment and then press the Enter key.
In the VAIO Recovery Center window, under Choose a program, click to select Restore Complete System. Follow the on-screen instructions.
The process will take for about an hour. If none of these works, then the recovery partition is not accessible anymore. You may contact Sony Support based on your location to order a Recovery Disc or use a retail version of Operating System.
For further assistance, we kindly recommend visiting our Sony Global Web site for information on contacting the Sony Support Center in your region at http://www.sony.net/SonyInfo/Support/.
Hope one of the process works. Good-luck.
Regards,
Vincent
If my post answers your question, please mark it as "Accept as Solution"

Restart to factory settings HELP!

So I want to restart my macbook pro early 2011 back to original factory setting i have the snow leopard disk but when i click on it to install it says i cant because i installed Lion on it.
the part i need help in is that i purchased Lion from the app store so I dont have to the disk its self to just restart it from there so I was wondering how am I going to be able to restart my laptop bak to originial factory settings?

Follow these instructions step by step to prepare a Mac for sale:
Step One - Back up your data:
       A. If you have any Virtual PCs shut them down. They cannot be in their "fast saved" state. They must be shut down from inside Windows.
       B. Clone to an external drive using using Carbon Copy Cloner.
          1. Open Carbon Copy Cloner.
          2. Select the Source volume from the Select a source drop down menu on the left side.
          3. Select the Destination volume from the Select a destination drop down menu on the right
              side.
          4. Click on the Clone button. If you are prompted about creating a clone of the Recovery HD be
              sure to opt for that.
               Destination means a freshly erased external backup drive. Source means the internal
               startup drive.
Step Two - Prepare the machine for the new buyer:
          1. De-authorize the computer in iTunes! De-authorize both iTunes and Audible accounts.
          2, Remove any Open Firmware passwords or Firmware passwords.
          3. Turn the brightness full up and volume nearly so.
          4. Turn off File Vault, if enabled.
          5. Disable iCloud, if enabled: See What to do with iCloud before selling your computer.
Step Three - Install a fresh OS:
     A. Snow Leopard and earlier versions of OS X
          1. Insert the original OS X install CD/DVD that came with your computer.
          2. Restart the computer while holding down the C key to boot from the CD/DVD.
          3. Select Disk Utility from the Utilities menu; repartition and reformat the internal hard drive.
              Optionally, click on the Security button and set the Zero Data option to one-pass.
          4. Install OS X.
          5. Upon completion DO NOT restart the computer.
          6. Shutdown the computer.
     B. Lion and Mountain Lion (if pre-installed on the computer at purchase*)
         Note: You will need an active Internet connection. I suggest using Ethernet if possible because
                   it is three times faster than wireless.
          1. Restart the computer while holding down the COMMAND and R keys until the Mac OS X
              Utilities window appears.
          2. Select Disk Utility from the Mac OS X Utilities window and click on the Continue button.
          3. After DU loads select your startup volume (usually Macintosh HD) from the left side list. Click
              on the Erase tab in the DU main window.
          4. Set the format type to Mac OS Extended (Journaled.) Optionally, click on the Security button
              and set the Zero Data option to one-pass.
          5. Click on the Erase button and wait until the process has completed.
          6. Quit DU and return to the Mac OS X Utilities window.
          7. Select Reinstall Lion/Mountain Lion and click on the Install button.
          8. Upon completion shutdown the computer.
*If your computer came with Lion or Mountain Lion pre-installed then you are entitled to transfer your license once. If you purchased Lion or Mountain Lion from the App Store then you cannot transfer your license to another party. In the case of the latter you should install the original version of OS X that came with your computer. You need to repartition the hard drive as well as reformat it; this will assure that the Recovery HD partition is removed. See Step Three above. You may verify these requirements by reviewing your OS X Software License.

Photomerge settings help, performance settings?

Having issues using photomerge with the latest version of Photoshop. I have about 120 images that are 16 mp RAW. What should I have my Photoshop Performance settings at? Cache Levels and Cache tile size? Also how much ram should I use?
My system settings are 18 gig of RAM, Core i7 920 like 4 different hard drives, Nvidia geforce 570 HD
I was using windows 8, now trying 7 but they still both crash and or take hours with no results.

I suggest Cache Levels = 6 as this is shown to speed Photomerge up vs. a setting of 4..
With 18 GB of RAM in your system I'd suggest settiing Photoshop to use 90%. But 18 GB of RAM is going to be WAY too little for 120 images of 16 megapixels each. 48 GB or more (possibly much more) would be helpful for that big a stitch.
Make sure you have a HUGE amount of free scratch space available - I mean at least 400 GB or more. Scour your system for Photoshop temp files left behind from your past failed runs.
Also, what's your ultimate goal in image size? Do you really need to stitch the images together after conversion to the full 18 MP size? Maybe you should set Camera Raw to deliver conversions at a smaller size to reduce system resource usage.
-Noel

FCP Project Settings Help - Mixing SD with HD

Hi,
I am trying to decide what settings to choose for my project and hope the experienced amongst you can shed some wisdom for me.
I am doing a promo ad to be shown in church on a windows pc with windows media player through a SD projector onto a 4:3 sized screen.
I will be filming a presenter with a Sony EX1 at 1920 x 1080 @ 25P. - square pixels
I have been given stock footage to include into the project that is 320 x 180, i have more footage to be delivered but I know it will be around the same SD res, maybe a bit larger.
The church auditorium has natural light and the projector is weak so video looks a little washed out at the best of times, so it is possible to get away with some pixelation as once its projected you really wont notice it.
My question is what do you recommend I set my project up as and what would be the best to export it.
I would like it to be widescreen (letterboxed) if possible.
Thanks
Dustin

Ok thanks, that is the only version they have.
It is a testimony about a women lost at sea in a canoe and the footage in question is a storm in the ocean, lighting, rain, waves etc...
The other footage is DV Pal of her speaking in a church so not too bad there.
I am actually trying to source some stock footage else where of a storm out to see at the moment as a last resort.
I will make the project native to the XDCAM footage and export to DVPAL AVI 720 x 560 anamorphic and see how it looks.
Thanks for your help guys, much appreciated.

Exporting Movie Settings - HELP!

Hello
I'm creating various movies on iMovie '08 and intend to burn them to DVD using iDVD. Once they are ready to be exported...what options are best to choose (bearing in mind I want to burn these to DVD). Is it best to choose 'Export Movie', or 'Export using QuickTime' ??
What is the best file format and video compression settings to choose? I really want a good quality finish when played back on DVD.
Hope this make sense and you can help!
Regards!

Hi
+what options are best to choose (bearing in mind I want to burn these to DVD)+<</div>
If You use miniDV tape material or interlaced material then iMovie'08 or 09 are not the tool at all due to that it trashes every second line.
I would use iMovie 1 to HD 6 or FinalCut Express or Pro.
How to export any good quality from iM08 or 09 is to others to explain.
*BUT on DVD quality*
1. iDVD 08 & 09 has three levels of qualities.
iDVD 6 has the two last ones
• Professional Quality (movies up to 120 min.) - BEST
• Best Performances (movies less than 60 min.) - High quality on final DVD
• High Quality (in iDVD08 or 09) / Best Quality (in iDVD6) (movies up to 120 min.) - slightly lower quality than above
2. From
• FCE/P - Export out as full quality QuickTime.mov (not selfcontaining, no conversion)
• iMovie x-6 - Don't use ”Share/Export to iDVD” = destructive even to movie project and especially so
when the movie includes photos. Instead just drop or import the iMovie movie project icon (with a Star on it) into iDVD theme window.
• iMovie’08 not meant to go to iDVD. Go via Media Browser or rather use iMovie HD 6 from start.
3. I use Roxio Toast™ to make an as slow burn as possibly eg x1 (in iDVD’08 or 09 this can also be set)
This can also be done with (Apple) Disk Util tool.
4. There has to be about or more than 25Gb free space on internal (start-up) hard disk. iDVD can't
use an external one as scratch disk (if it is not start-up disc).
5. Verbatim ( also recommended by many - Taiyo Yuden DVDs - I can’t get hold of it to test )
6. DVD-R (no +R or +/-RW)
7. Keep NTSC to NTSC - or - PAL to PAL when going from iMovie to iDVD
8. Don’t burn more than three DVD at a time - but let the laser cool off for a while befor next batch.
iDVD quality also depends on.
• HOW much free space is there on Your internal (start-up) hard disk. Go for approx 25Gb.
less than 5Gb and Your result will most probably not play.
• What kind of movie project You drop into it. MPEG4 seems to be a bad choice.
other strange formats are .avi, .wmv, .flash etc. Convert to streamingDV first
Also audio formats matters. I use only .aiff or from miniDV tape Camera 16-bit
strange formats often problematic are .avi, .wmv, audio from iTunes, .mp3 etc
Convert to .aiff first and use this in movie project
• What kind of standard - NTSC movie and NTSC DVD or PAL to PAL - no mix.
(If You need to change to do a NTSC DVD from PAL material let JESDeinterlacer3.2.2 do the conversion)
(Dropping a PAL movie into a NTSC iDVD project
(US) NTSC DVDs most often are playable in EU
(EU) PAL DVDs most often needs to be converted to play in US
UNLESS. They are plabacked by a Mac - then You need not to care
• What kind of DVDs You are using. I use Verbatim DVD-R (this brand AND no +R or +/-RW)
• How You encode and burn it. Two settings prior iDVD’08 or 09
Pro Quality (only in iDVD 08 & 09)
Best / High Quality (not always - most often not)
Best / High Performances (most often my choise before Pro Quality)
1. go to iDVD pref. menu and select tab far right and set burn speed to x1 (less errors = plays better) - only in iDVD 08 & 09
(x4 by some and may be even better)
2. Project info. Select Professional Encoding - only in iDVD 08 & 09.
Region codes.
iDVD - only burn Region = 0 - meaning - DVDs are playable everywhere
DVD Studio pro can set Region codes.
1 = US
2 = EU
Yours Bengt W

Nokia E5 Calendar Sync Settings Help

Hello,
I'd like to sync my calendar on Ovi.com with teh one on my Nokia E5. I followed all these instructions here:
1. On your computer, go to www.ovi.com
2. Sign in your account
3. Click on the calendar tab
4. Click on “manage device”
5. Click on remove device, and then click again on remove device
6. Click on add device
7. Choose Nokia E5 on the list, and then press Next
8. Enter your mobile number in international format (e.g. +441234568790)
9. Choose the correct time zone
10. Click on Next, and then done
B. Follow the setup instructions
1. Wait for the SMS message on your device from Nokia
2. Enter the pin that was provided to you from Ovi.com
3. Save the message in your device (go to Options and select Save)
C. Follow the synchronization instructions
1. On your device, go to Menu
2. Choose Ctrl. panel
3. Select Connectivity
4. Choose Sync
5. Select Options
6. Choose Synchronise
However, I cannot successfully syncronise. Trying it with the original sync profile resulted in this message on Ovi.com:
Your device is partially configured. Please complete the configuration by synchronizing the device or remove it to add another.'I tried to adapt the sync settings, but need help here. What do I need to fill in for:
Sync Profile Name
Server Version (1.2 currently)
server ID
Data Bearer
Network connection (currently my WiFi)
Host address
Port
User name (I use my Ovi.com one)
password (I use the according one)
My current profile results in the message 'invalid Host address'
Many thanks for your help,
Robert

I can get Mail for Exchange to sync the contacts and the calendar working for a normal gmail account...
...HOWEVER, I can't get it working for a Google Apps account using the same setup...what's the issue?

Redner settings help

Similar Messages

Maybe you are looking for