Refurbished Cisco Switches, worth it for home lab?
Robert5205 wrote:
Cablesandkits.com has some great prices on old Cisco gear. This week they have a 3560 PoE 48-port switch for $150.
Yes, it is absolutely worth it to have real hardware in your hands. Packet tracing is fine, but it's not real life.
Yeah I believe they are being sold by Cablesandkits through newegg. Any suggestions on which switch or features I should look for? Really I want something that's managed but beyond that I'm not sure.
So I been thinking about getting a decent switch to play around with at home. During my search I found there's a good bit of "refurbished" Cisco switches online and was wondering if they are worth trying out. Figured they are beyond EOL hence the cheapness, the one I'm looking at is a Cisco 2900 series for like $30 bucks. Pretty new in IT and working on my Network+ and starting to look into the Cisco certs at the moment so having an actual Cisco switch would be useful.
This topic first appeared in the Spiceworks Community
Similar Messages
-
Cisco Model 870 router for home office connected to WRT160NL wireless router for personal use
I am using a Cisco Model 870 router for home office. I just bought a WRT160NL wireless router for home use. I setup the personal wireless router off the personal port of the 870 and can connect with my PC but not with my MAC machines. It can see the Network but when it asks me for passwords, it says they are wrong, which after several attempts I know they are correct.
The new router is setup as WPA2 personal. Can you advise?
Cisco Account Manager- ServicesI think I answered my own question. I tried downloading something on my desktop and checked my cellular usage afterwards didn't go up so it's using my home internet and not my data plan.
-
Configuration Cisco switch 802.1x for ISE
Hi dears,
I configurated EAP_FAST authentication on Cisco ISE from Cisco Video material. Now I need full 802.1X configuration in cisco switch guide or video link.
Please provide this.
Thanks.See this link:
http://www.cisco.com/c/en/us/td/docs/security/ise/1-2/user_guide/ise_user_guide/ise_sw_cnfg.html -
Hello all.
I need some advice on what books and hardware to set up a BASIC voice lab at home. I have a 2691 and one IPPhone but don't know the minimum devices/modules to practice two IPPhones VoIP calls in a lab and get proficient. I also can't find all Ciscopress books for each of the CCVP exams.
Any help and advice is greatly appreciated.
Thank you.CCVP require multiservice routers and other voice interface cards, Callmanager, CME, Gatekeepers and 3 IP phones
http://www.cisco.com/web/learning/le3/le2/le37/le65/learning_certification_type_home.html -
Lab equipment for home study ?
Hi Guys,
I've just bought the latest CCNA R/S study guide and as part of my study would like to put together a suitable lab for home use. I've seen labs on ebay for around £70 and wondered if these are suitable for the latest exam. The lab equipment tends to be made up of old layer 2 switches and routers - as you'd expect for the price.
Money is an object so ideally I'd like to keep the cost down, but I'd rather spend extra money buying something worth while than throw money away on unsuitable equipment.
Any advice and opinions would be greatly appreciated.
Thankshi,
go with couple of 1841 and 2960. you might get lucky with ebay auction if you're patient enough.
that's what i personally do in my free time. -
Hello,
I was wondering what would be needed to set up a basic Voice lab for home. I have a lab currently of 1 2610, 12 2500's, 1 4000. A 2950 switch, and a Catalyst 5000 switch.
I know I would need atleast two IP Phones, 7960 or 7940's. Would a Cisco 2620 with one FXO and one FXS vic cards be a good gateway? What would I need to run CCM or Cisco CME. Can I run Call Manager express on the 2620?
Any help is appreciated!
Thanks again!!
ScottYou can run CME on a 2620XM. See the following site for specific platform informaiton for CME version 3.4.
http://www.cisco.com/en/US/products/sw/voicesw/ps4625/prod_installation_guide09186a008055677f.html
Hope this helps.
Steve -
VOIP home lab with cisco 2620 and VIC-2FXO port
Hi all,
I m considering building a home lab for studying CCVP, the lab would be based on the follow components :
- CUCM 8.X (already installed)
- A couple of soft phones running in VMWARE with IP Blue and CIPC (they are already in place and registered with the CUCM)
- Cisco router 2620 with NM-2V and VIC-2FXO-M2 (for europe, I'm in France)
so here are my questions :
1/ it looks like the NM-2V comes with integrated DSP, so I should not need more DSP, I have got one PSTN analogic line only so I can make only one call at a time, please confirm
2/ my analog line comes via my home internet provider dsl box, i have already tried to connect an analog phone and it works, please confirm the router will be able to receive and place calls
thanks for your help, I m looking forward to begin my voice lab1. Yes, the NM-2V has built-in DSP resources for up to four calls (max voice port density with two 1st generation VICs). You cannot add further DSP chips to the NM-1V/2V, nor would you need to for what it does. You have one PSTN phone line, thus you can only make one call at a time. If you had a second line you could use the other FXO port for a second concurrent call.
2. If the phone line works then it will work with the router to make and receive calls. As Gregory said, just configure dial peers for what you need to do.
Here is some info on the NM-2V:
http://www.cisco.com/en/US/products/hw/modules/ps2617/products_tech_note09186a0080094ac0.shtml -
Setting up Cisco Aironet 1250 for home use
Hey everyone,
I'm rather new to the whole Enterprise Router lines. I've set up countless networks with Linksys routers in the past. However, this Aironet is giving me more trouble than I'd want it to. I was wondering if anyone could help. I've assigned it an IP Address and accessed that In-Browser interface and set up an SSID and activated the two extensions. I've been able to connect to the router with my computer and access the internet without restriction. However, when I attempt to connect a second PC or Laptop to the network, it won't allow network access to the second device. I've been stuck there forever. Is there any specific setup method I need to use to make sure more than one workstation/device? I want to use this router for home use, I often use laptops and move around the house a lot, so the advantage of better connection signal and speed is well worth it. Any help is highly apprieciated. If you need more information, don't hesitate to contact me.Sorry for my late reply. Here is the config:
It wasn't connected to anything. This was a raw pull from a fresh cold boot.
IOS Bootloader - Starting system.
Xmodem file system is available.
flashfs[0]: 150 files, 7 directories
flashfs[0]: 0 orphaned files, 0 orphaned directories
flashfs[0]: Total bytes: 31868928
flashfs[0]: Bytes used: 6406144
flashfs[0]: Bytes available: 25462784
flashfs[0]: flashfs fsck took 16 seconds.
Reading cookie from flash parameter block...done.
Base Ethernet MAC address: 54:75:d0:dd:b5:12
Loading "flash:/c1250-k9w7-mx.124-10b.JDA3/c1250-k9w7-mx.124-10b.JDA3"...##################################################################################################################################################################################################################
File "flash:/c1250-k9w7-mx.124-10b.JDA3/c1250-k9w7-mx.124-10b.JDA3" uncompressed and installed, entry point: 0x3000
executing...
Restricted Rights Legend
Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.
cisco Systems, Inc.
170 West Tasman Drive
San Jose, California 95134-1706
Cisco IOS Software, C1250 Software (C1250-K9W7-M), Version 12.4(10b)JDA3, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2009 by Cisco Systems, Inc.
Compiled Sun 07-Jun-09 03:50 by prod_rel_team
Image text-base: 0x00003000, data-base: 0x01000000
Initializing flashfs...
flashfs[1]: 150 files, 7 directories
flashfs[1]: 0 orphaned files, 0 orphaned directories
flashfs[1]: Total bytes: 31868928
flashfs[1]: Bytes used: 6406144
flashfs[1]: Bytes available: 25462784
flashfs[1]: flashfs fsck took 4 seconds.
flashfs[1]: Initialization complete....done Initializing flashfs.
Warning: the compile-time code checksum does not appear to be present.
Radio 1 A600 8000 0 0 A8030000 30
Radio 1 A600 8000 0 0 B8030000 13
tx_paks 1293
tx_paks 646
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html you require further assistance please contact us by sending email to
[email protected]. AIR-AP1252AG-A-K9 (PowerPC 8349) processor (revision C0) with 49142K/16384K bytes of memory.
Processor board ID FTX1423902R
PowerPC 8349 CPU at 533Mhz, revision number 0x0031
Last reset from power-on
1 Gigabit Ethernet interface
2 802.11 Radio(s)
If
cisco
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 54:75:D0:DD:B5:12
Part Number : 73-10425-06
PCA Assembly Number : 800-27630-06
PCA Revision Number : B0
PCB Serial Number : FOC142025F4
Top Assembly Part Number : 800-29039-03
Top Assembly Serial Number : FTX1423902R
Top Revision Number : A0
Product/Model Number : AIR-AP1252AG-A-K9
Press RETURN to get started!
*Mar 1 00:00:06.211: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed
*Mar 1 00:00:07.039: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0
*Mar 1 00:00:07.543: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 1
*Mar 1 00:00:09.587: %SYS-5-CONFIG_I: Configured from memory by console
*Mar 1 00:00:09.591: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C1250 Software (C1250-K9W7-M), Version 12.4(10b)JDA3, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2009 by Cisco Systems, Inc.
Compiled Sun 07-Jun-09 03:50 by prod_rel_team
*Mar 1 00:00:09.591: %SNMP-5-COLDSTART: SNMP agent on host Cisco1250 is undergoing a cold start
*Mar 1 01:37:52.027: %LINK-3-UPDOWN: Interface GigabitEthernet0, changed state to up
*Mar 1 01:37:52.027: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
*Mar 1 01:37:52.707: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
*Mar 1 01:37:53.467: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Mar 1 01:37:53.467: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to down
*Mar 1 01:37:53.847: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
*Mar 1 01:37:54.467: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Mar 1 01:37:54.695: %CDP_PD-4-POWER_OK: Full power - INJECTOR_DETECTED inline power source
*Mar 1 01:37:54.703: %DOT11-4-NO_HT: Interface Dot11Radio1, Mcs rates disabled on vlan 0 due to not using AES encryption or
*Mar 1 01:37:58.303: %DOT11-6-FREQ_USED: Interface Dot11Radio1, frequency 5180 selected
*Mar 1 01:37:58.307: %LINK-3-UPDOWN: Interface Dot11Radio1, changed state to up
*Mar 1 01:37:58.307: %DOT11-4-NO_HT: Interface Dot11Radio0, Mcs rates disabled on vlan 0 due to not using AES encryption or
*Mar 1 01:37:58.311: %DOT11-6-FREQ_SCAN: Interface Dot11Radio0, Scanning frequencies for 13 seconds
*Mar 1 01:37:59.307: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
*Mar 1 01:38:00.307: %LINK-3-UPDOWN: Interface BVI1, changed state to down
*Mar 1 01:38:02.931: %LINK-3-UPDOWN: Interface BVI1, changed state to up
*Mar 1 01:38:11.919: %DOT11-6-FREQ_USED: Interface Dot11Radio0, frequency 2462 selected
*Mar 1 01:38:11.923: %LINK-3-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 1 01:38:12.923: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
Cisco1250>enable
Password:
Cisco1250#show running-config
Building configuration...
Current configuration : 1717 bytes
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname Cisco1250
enable secret 5 $1$jDeQ$cFdx0aHAd8wj8tk6CCmXq/
no aaa new-model
dot11 ssid Home Network
authentication open
guest-mode
power inline negotiation prestandard source
username Cisco password 7 05280F1C2243
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
encryption key 1 size 128bit 7 23D0220D02AE7FA723492AA01E34 transmit-key
encryption mode wep mandatory
ssid Home Network
station-role root
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface Dot11Radio1
no ip address
no ip route-cache
encryption key 1 size 128bit 7 0B4935657C801B3620154AB56630 transmit-key
encryption mode wep mandatory
ssid Home Network
dfs band 3 block
channel dfs
station-role root
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface GigabitEthernet0
no ip address
no ip route-cache
duplex auto
speed auto
bridge-group 1
no bridge-group 1 source-learning
bridge-group 1 spanning-disabled
interface BVI1
ip address 192.168.0.1 255.255.255.0
no ip route-cache
ip http server
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
snmp-server community Community RW
bridge 1 route ip
line con 0
line vty 0 4
login local
end
They way I connect it in the network is as follows:
BrightHouse Networks ISP Modem --> Cisco Aironet 1252 --> Incoming connections from computers and laptops.
Any ideas? -
Confused how to set-up a PC & laptop with Cisco WRVS4400N VPN for home use
Just bought a new PC and laptop and was recommended by (CDW) to use a Cisco WRVS4400N to set up the VPN.
For home use, only the PC and laptop, both running Windows 7. I use Comcast as my ISP.
The mountains of docs confuses me to no end, can anyone simplify this for me. I look at all the details and do not know where to start.
In short,
(1) configure router to recognize my PC and Comcast, and I guess the laptop.
(2) configure laptop to go wireless and communicate with PC.
Any assistance would be much appreciated.
Thanks,
TerryFor a very small office and a minimum of admin and tech know how, one approach i'd suggest is to not worry about user id collisions at all. any time anyone wants to use a mac you just set them up as a user, using consistent names/passwords.
Have a "Work" volume on each mac that has "ignore ownership on this volume" ticked. that way UID collisions aren't important.
You can make a Desktop folder on the Work volume and make a SYMBOLIC LINK from every user's home that replaces their desktop with the desktop folder on the Work volume.
Make it known that the user's home is for personal stuff ONLY, and the Work volume (inc the desktop) is where work in progress lives.
At a later date with some confidence in your network and your admin skills you could impose consistent UIDs using an OD master -
Rrack mounting brackets for Cisco switch SF300-48P ?
Does anyone know how to get rack mounting brackets for Cisco switch SF300-48P ?
You might be able to get them through Cisco support. Check this thread: https://supportforums.cisco.com/discussion/11201291/sf-300-series-rack-mount-brackets
-
Has anyone develped an EM plug-in for Cisco switches or routers
Folks,
Has anyone develped an EM plug-in for Cisco switches or routers? Please reply to this thread if you have developed one and would like to share your experience in developing this plug-in?
Thanks,It's probably not the conversion from CMYK to RGB that's causing the problem, but color profile (ICC) embedding in Photoshop. Fireworks doesn't read color profiles. You might be able to create an action to remove the color profile in Photoshop and then batch process the images with it.
-
What's "SAVE" configuration command for Cisco switch/ router?
What's "SAVE" configuration command for Cisco switch / router? I know Switch#copy running-config startup-config works well,
but so long, any other command that easy to remenber?What's "SAVE" configuration command for Cisco switch / router? I know Switch#copy running-config startup-config works well, but so long,
any other command that easy to remenber?
yes, here: Switch#write,and want to know more about the Cisco switch, please visit:http://www.3anetwork.com/cisco-switches-price_c1 -
Configure Domain Controller ( PDC emulator) as NTP source for Cisco switch 6509
Hi All,
My Org consists of 2 DC one Physical and One Virtual. All Roles are on Physical machine. I ran a W32tm /Query /Configuration command on PDC emulator and the results are confusing.My PDC is using time source VMICTimeProvider a syou can see below.
VMICTimeProvider (Local)
DllName: C:\Windows\System32\vmictimeprovider.dll (Local)
Enabled: 1 (Local)
InputProvider: 1 (Local)
My first Question is that Is it Ok for PDC emulator to use this time source or should I change to some Other source like pool.ntp.org or time.windows.com,0x1.
My Second Question is that I have a core switch cisco 6509 and I want this switch to use my NTP server (PDC emulator ) as NTP source,but at present I cannot as I am getting this error on switch.(no select intersectionTP )
Can Any one help ... Its is urgent
Thanks in Advance
EagleAshYou should not make your DCs sync their time with your Hypervisor. This usually ends with time synchronization problem so I would recommend to disable that on your DCs and domain joined VMs and use an external NTP server to sync time on your PDC while using
your AD forest topology for time sync on other DCs and domain-joined computers.
I have already started a Wiki article that describes how to configure time sync in an AD domain and you might consider using the GPO configuration option that is stated: http://social.technet.microsoft.com/wiki/contents/articles/18573.time-synchronization-in-active-directory-forests.aspx
For the CISCO switch, I would recommend asking them in CISCO forums.
This posting is provided "AS IS" with no warranties or guarantees , and confers no rights.
Get Active Directory User Last Logon
Create an Active Directory test domain similar to the production one
Management of test accounts in an Active Directory production domain - Part I
Management of test accounts in an Active Directory production domain - Part II
Management of test accounts in an Active Directory production domain - Part III
Reset Active Directory user password -
Virtual IP for two redundant PCs in Cisco Switch
Hi Team,
We have redundant Computers connected to Switch . There is the third system also connected to the switch.
We want the two redundant PC ethernet to look like one for the third system. We want a virtual IP for the third System to get connected to any one of the two PC’s.
we have a Cisco Small business switch.Is that possible in this switch to create a virtual IP for redundancy ?
which cisco switch supports this functionality ??
Attached is the diagram of the setup.Hi,
That is not possible with just a switch. You need some sort of load balancer in front of the switch with a virtual VIP. So when a packet comes from SCATA to PC1 and if PC1 is not available it will send it to PC2. A10 makes pretty good load balancers.
http://www.a10networks.com/
Is that what you are trying to do?
HTH -
Firewall Ports Required for NAC manager to manage/add Cisco switch
Hi,
I am trying to add cisco switches to the NAM, however i am not able to add the switch as I am getting the error "unable to control switch" I have tried to open ports 161-162 on the firwall; if i was to allow any traffic between the NAM and switch, the cisco NAM is able to add/manage the switch.
Not sure what other ports may be required for cisco NAM to manage the switch?
Thanks.Hi,
AFAIK, only the UDP ports 161-162 for the SNMP communication need to be open.
Please make sure you have configured the correct port on the switch:
(config)# snmp-server host 172.16.1.61 traps version 2c cam_v2 udp-port 162 mac-notification snmp
If still not working i would check the logs on the firewall for any blocked traffic between the CAM and the switch.
HTH,
Tiago
If this helps you and/or answers your question please mark the question as "answered" and/or rate it, so other users can easily find it.
Maybe you are looking for
-
TestStand won't load vi in runtime
I'm runing LabVIEW 2011 version 11.0f2. TestStand 2010 SP1. We tried deploying a packed library to a test system but the run-time will not load the VI. Depending on the VI selected, we get a variety of different errors with the ! in teststand sayin
-
How to use execute query For a single record
Hi All, I am working with oracle forms 10g, I have developed a custom form. I the form user enter some data and click save in the menu and data get inserted into my table. Inside the insert statement i have hardcoded some values, Once data get insert
-
Ipod screen says to connect to itunes but won't let me enter my password. Tried recovery mode but when I click 'restore' itunes says it cannot connect to update server. Help!
-
I have a mac air and my iphone is not showing up in itunes?
I have checked system profiler and it shows up as connected to the usb port
-
Drag and drop option not active - Captivate 8
Is there a particular slide you need to use or something else you need to have on your slide in order to activate the drag and drop menu item? All other menu items in the Interaction menu are active, but drag and drop.