Reg:Low speed of the fibre link

Hi,
A strange issue has risen as few fibre links connected from core using STM1 and of 2Mbpsare showing following output and there speed is very slow,kindly help me find out the issue and help resolving the issue.Output of one of the links is as given below,
CORE#sh int Se1/1/0.1/1/4/3:0
Serial1/1/0.1/1/4/3:0 is up, line protocol is up
Hardware is SPA-1XCHSTM1/OC3
Internet address is x.x.x.x/30
MTU 1500 bytes, BW 2048 Kbit, DLY 20000 usec,
     reliability 255/255, txload 116/255, rxload 6/255
Encapsulation HDLC, crc 16, loopback not set
Keepalive set (10 sec)
Last input 00:00:01, output 00:00:00, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 12055
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 56000 bits/sec, 64 packets/sec
5 minute output rate 937000 bits/sec, 91 packets/sec
     1351190 packets input, 155951746 bytes, 0 no buffer
     Received 12974 broadcasts (0 IP multicasts)
     0 runts, 0 giants, 0 throttles
     751628 input errors, 94423 CRC, 54516 frame, 0 overrun, 0 ignored, 602689 abort
     1596894 packets output, 1478271189 bytes, 0 underruns
     0 output errors, 0 collisions, 11 interface resets
     0 output buffer failures, 0 output buffers swapped out
     9 carrier transitions no alarm present
VC 11: timeslot(s): 1-31, Transmitter delay 0, non-inverted data
Thanks,

Look at your interface counters. you have crcs, drops and aborts.
1. clear the counters on this interface & note the time you did so.
2. do a show interface at 15 minute intervals for one hour, then again 24 hours after the orginal clear counters.
this will give you a measure of how bad things might be.
3. you need to then double check all the hardware from your router to the network point of presence clean connectors and verify light level.

Similar Messages

Crazy low speed from the off

hi all,
im a (relatively) new BT customer in a brand new build house. Before moving in i did some digging around to see what sort of speeds i could get with different providers and settled on BT as they seemed to be the best average and i preferred the BT home hub compared to the other ISPs offerings. (i would also add that im an IT engineer so did the usual **bleep** studying beforehand although whether this is a disadvantage remains to be seen)
i have been on the service for a month or two now and am getting dreadful low speeds. On average i get 750kbps down (max 950kbps) and 200kbps up. i have checked the disitance to the exchange with all the usual tools and its 0.9 miles away apprently. I have checked out all of my wiring and tried several ADSL filters but this is the speed i am stuck with.
I opened a case with BT and am getting the usual. (i would mention at this point that there is an issue with the BT site where you check what speeds you MAY get, if you're not a BT customer (which i wasn't) and you stick your address you get the 'up to 12meg' result, if you ARE a BT customer then you put your actual phone number in you get the REAL result. in my case i was advised i would get 'around 12meg' but then i was told i would actually get 'around 1meg', this is not good)
i am advised by BT that my exchange will get ADSL2 by the end of this year (2x-3x? ADSL) but im not counting my chickens. For info i came from a great 20meg cable connection in my old house so theres a big old step in the right direction
Im sure that this has been covered many a time on these forums so apologies if i just havent found my answers and feel free to just link me somewhere or copy and paste some jazz
anyone have any ideas or suggestions?
thanks in advance
David

As already been advised in bits and bobs:
The top tips for a good connection on a long line are as follows:
1) Is removing the bell wire as I have already advised and to have a good clean socket, with all the wires moved away from the connected wires, or snipped off all together, just to ensure as little interference as possible.
2) Would be to get a business hub, there are two available on Ebay, the 2701 (pictured right) and the 2700hgv (pictured left), now the 200HGV's seem to give a better sync speed by about 300kbps give or take, but I find they are less stable, whereas the 2701 decreases the sync speed but is far more stable, and good at holding onto low SNR's, I've seen it hold all night at -2dB Noise Margin and Im on a 9km line.
3) Would be to get a shieled RJ11 cable, as this can reduce the amount of interference, and also importantly it has the twists in as the telephone cables do to refract UV radiation, and Impulse noise just to name a few things. And the ends of them are gold plated with 24k gold just to ensure maximum transition .
Regards Edd
Check your Line
BT Speedtester

Low speed of the printing on Inkjet 2800

Hello!
I'm guy from Kazakhstan, so sorry for possible grammatical mistakes.
We have HP Inkjet 2800 in office. His speed of the printing is very low. Processing lasts around 1 minute...
This problem appeared since windows 7 was installed on PC (I'm calling it #1), which have connection with printer. Our printer was good when windows XP was installed. Other PCs are connected with PC #1 in LAN. PCs with windows 7 can print. PCs with windows XP have drivers for 2800 but can't print.
Also we used little Wi-Fi printserver to connect printer in LAN. It allowed to print from PCs with windows XP, but the speed of the printing was very low too (around 1 minute), even in case of 0.5Mb-sized files.
I have 2 questions:
1. Are there any variants how to provide normal speed of the printing (according to technical characteristics of the printer)?
2. How to provide work of windows XP and windows 7 at the same time?
Perhaps purchase of the additional device will help?
Yours faithfully, John_White

Hi,
Try these steps given below to help solve the issue :
Check the port setting: The port setting configuration in your system might not be set to ECP. See the documentation that came with the computer for information on how to change the port setting, or contact the computer manufacturer.
Check the printer software settings: The printer prints slower when Best or Maximum dpi is selected as the print quality. To increase the print speed, select different print settings in the printer driver.
I work for HP but my posts and replies are my own.
Make it easier for other people to find solutions, by marking my answer with \'Accept as Solution\' if it solves your problem.
Click on the BLUE KUDOS button on the left to say "Thanks"

Bt infinity 2 low speed from the off.

Hello there, I upgraded to bt infinity 2 with home hub 5 a few weeks ago. My BT internet and wireless in the house had previously been quite good.
I was told the new cabinet could give me download speeds of 80mps.
Right from the off the speed with fibre-optic has been poor. Have been testing from the off and the download speed has been averaging out at around 40 (best ever 44mps). Upload has been averaging around 7. Ping reading usually around 30. Lowest speed was 3.6 mps upload!
Most of these test results were achieved with direct ethernet connection (which means a cable across the room so its not my ideal option). Wireless connection gives similar results. davolo home plugs have been the slowest of all - reducing speed to a crawl. Weird since they previously worked well with my old school broadband and are the 500mps type.
After a week of slow speeds and many phone calls and tests an engineer was sent out. He said the initial engineer had failed to establish the correct main socket which is outside the house. He did some work in there and went away saying speeds would gradually rise. Ansd that 80 mps wasn't realistic but something around 60 was do-able. Its now a week later and things have not improved.
I've enclosed 2 recent test/performance results. My line profile now seems to have very low projections.
would much appreciate any help/thoughts. Should add that I've not switched the hub on or off.
cheers again for the assistance.

many thanks for the prompt replies.
It would be great to think the speed will just rise after another week or so.
In case there is still a problem here is the data requested.
cheers
G

I Can't Burn a CD any more! and a lower speed does nothing - HELP!

I have been burning CDs on this machine (imac 10.3.9) the same way for years and years. (7)
Up till last month.
This is what I get when I burn a playlist.
"itunes can not burn this cd because your burn speed is too fast for you cd burner or media. Choose a lower speed in the burning pane then try burning again."
I've tried that - even though that seems silly considering I've had no problems at my current settings until now. The lowest burn speed (1) gives me the same error.
I'm hating life and my mac right now, something I though I'd never say.
Anyone?

If you don't have Nero, check out http://discussions.apple.com/message.jspa?messageID=9229334#9229334. I think some people have found a way to get just the Burn Rights program.
If that doesn't work, some people seem to have luck with editing the registry or messing with filters or gear drivers. Check out this discussion starting with Tytus (he came up with the Nero fix) on March 22:
http://discussions.apple.com/thread.jspa?threadID=1939904&tstart=0
Hope this helps!

Read per axis status / run-stop don't work at low speed

Hello,
This is my fisrt motion program. I don't understand why the "read per axis status" don't send me the correct status for "run/stop" (only this status) when I run a low speed. The other status are all right. Impultions are still generated (In realyty motor run...)
I put a simple example to illustrate. Perhaps is it a wrong configuration in MAX but this seems unlikely. I can't join my Max config because ".nce" are not accepted in attached files.
Thank you wery much
Attachments:
One-Axis Move (Accel - Max Velocity - Decel) with read status.vi ‏26 KB

I realize this is an old post but wanted to post the solution in case others run across it. The reason the indicator is not working at low speeds is because it operates on a threshold. The default setting is for it to display false when running under 4000 steps or counts per second. Refer to KnowledgeBase 4XHD6DZY: Why does my Run/Stop bit not appear active while my motor is running?
Alex Person
NI-RIO Product Support Engineer
National Instruments

Internet connecting at much lower speed lately

I have HSI Enhanced and have had it for 10 months at this location and for a number of years at my previous location. Last October I was connecting at 3360 / 832 kbps. After some months it went down to around 2800 / 832 kpbs. I wasn't crazy about speeds getting lower as time went on rather than the connection being improved, but it was pretty much free of disconnects and reliable so I was happy with it.
In the past month or so I had noise on my voice line which Verizon fixed, but my connection is now 1792 / 448 Kbps all the time, that is a drop I will not accept if this is the way it is going to be from now on. Also there is a lot of losing the connection, not to the DSL, that light stays on but the internet light goes off. I went through the usual channels online chat, telephone support to wherever that goes. I'm done with all that, that's good for people with trouble using their modem, etc. or can't connect it but not what I am looking for.
Finally they sent out a tech who was a nice enough person, what he did was call a central office and after them first claiming the lower speed was the right speed they put the connection back in the area of 3360/832. Then they said it will probably adjust itself to down around 2800 down, which it what I had before so I was OK with it. After several days with a number of disconnects (they don't last too long but very annoying) I am back to 1792 / 448.
I am using the same modem - Actiontec GT704WGB
I don't need a tech call here in the house again, nothing has changed in here since I moved in months ago. They can check the outside signal without me waiting around for them. They don't have to stand in here to call an office on their tablet.
I need to hear from Verizon personnel that can tell me LOCAL information about why my connection speed has tanked and why there are dropouts now. And most importantly, why it can't be the same as it was for all those months. As I said, I was happy with that - especially when it was 3360 / 832 kbps.
Solved!
Go to Solution.

When Verizon turns your speed back up, they have to disable the optimization system they use on the lines to maintain your speed, since it sounds like that is just turning your speed back down after a few days. Make them fix it back again.
For future note, if you do have problems with your DSL and you're also having audio quality issues with your phone, call Voice Repair, and leave DSL support out of the mix. DSL support usually dials back the speed for a line issue from what I've seen as a first try basis. If you do have noise that disappears when the DSL modem is off, then that could be from other things which DSL support OR phone support will be needed for.
Ex: Two years ago I had a problem with my Frontier DSL line having a ton of static on the line. The DSL modem was not synchronizing, however the noise stopped when I shut off the modem. It turns out, the night before lightning struck a tree outside of my home, and caused the DSL modem which was several years old to fry. The modem was still powering up, but the chip responsible for the DSL connection itself was blown. A new modem from Frontier via DSL Support fixed the DSL connection AND the static.
Ex2: At a local business with Verizon DSL, they hear static on their line from time to time, but only while the DSL is active. The problem was not with the DSL itself or any filters, but as the static got worse it began to show up without the DSL being connected. Voice repair was dispatched instead of calling DSL Support, and resolved the problem by running new cable between the building and the Verizon copper trunk. In addition, they found and corrected some corroding splices.
========
The first to bring me 1Gbps Fiber for $30/m wins!

Sky Fibre constant drop out and low speed

Hi everyone,
Just recently switched provider from Plusnet fibre to Sky fibre and boy, has it been a stressful few days. First off, our fibre went live on the 6th of this month but these last couple of days I've been experiencing low speeds between 10-20 mb which I understand is meant to be normal (Never had this issue when I joined plusnet) and I have constant drop outs when I'm surfing the net or playing internet games on my Wii U
I've phoned Sky within the last two days and told them what's going on and they've done some tests on their end and they are telling me that I'm getting speeds up to 41 mb which I'm not getting, but they can't seem to understand why I keep having this drop out issue with my devices and my laptop and my gaming console. They have sent me a new hub, but I personally don't think sending out a new hub will make a difference. I've stuck a a Ethernet cable into my Sky fibre router and attached a openreach router, to the other end and see if that stops the drop out.
I'm inclined to leave sky, because I have a feeling this poor service will continue, unless someone can help me.
Thanks

Jan 1 00:00:07 syslog: BusyBox v1.17.2
Jan 1 00:00:16 syslog: Line 0: xDSL G.994 training
Jan 1 00:00:24 syslog: Line 0: VDSL G.993 started
Jan 1 00:00:31 syslog: Line 0: VDSL2 link down
Jan 1 00:00:34 syslog: Line 0: xDSL G.994 training
Jan 1 00:00:42 syslog: Line 0: VDSL G.993 started
Jan 1 00:01:01 syslog: Line 0: VDSL2 link up, Bearer 0, us=9995, ds=39998
Jan 1 00:01:04 syslog: ptm0.1 - WAN link UP.
Jan 1 00:01:04 syslog: Received valid DHCP lease from server. Connection UP.
Jan 1 00:01:04 syslog: Connection Up. SNO/MAC/IP: [A502155D006292/C03E0F9F81C4/151.231.97.46]
Jan 1 00:01:05 syslog: Send out NTP request to ntp1.isp.sky.com
Jan 1 00:01:05 syslog: Time has been set from ntp1.isp.sky.com
Aug 9 00:05:11 syslog: Received NTP Sync Reply from ntp1.isp.sky.com
Aug 9 00:11:49 syslog: eth2 (switch port: 1) Link UP 100 mbps full duplex
Aug 9 00:11:56 syslog: eth2 (switch port: 1) Link DOWN.
Aug 9 00:11:57 syslog: eth2 (switch port: 1) Link UP 100 mbps full duplex
Aug 9 00:12:04 syslog: eth2 (switch port: 1) Link DOWN.
Aug 9 00:12:06 syslog: eth2 (switch port: 1) Link UP 100 mbps full duplex
Aug 9 00:12:08 syslog: eth2 (switch port: 1) Link DOWN.
Aug 9 00:12:09 syslog: eth2 (switch port: 1) Link UP 100 mbps full duplex
Aug 9 00:12:21 syslog: eth2 (switch port: 1) Link DOWN.
Aug 9 00:12:22 syslog: eth2 (switch port: 1) Link UP 100 mbps full duplex
Aug 9 00:12:23 syslog: eth2 (switch port: 1) Link DOWN.
Aug 9 00:12:24 syslog: eth2 (switch port: 1) Link UP 100 mbps full duplex
Aug 9 00:12:32 syslog: Line 0: VDSL2 link down
Aug 9 00:12:34 syslog: Clear IP addresses. IP connection DOWN.
Aug 9 00:13:41 syslog: eth2 - WAN link UP.
Aug 9 00:13:41 syslog: Received valid DHCP lease from server. Connection UP.
Aug 9 00:13:41 syslog: Connection Up. SNO/MAC/IP: [A502155D006292/C03E0F9F81C4/151.231.102.13]
Aug 9 00:19:01 syslog: Connection Up. SNO/MAC/IP: [A502155D006292/C03E0F9F81C4/151.231.102.13]
Aug 9 00:47:49 syslog: Connection Up. SNO/MAC/IP: [A502155D006292/C03E0F9F81C4/151.231.102.13]
Aug 9 01:22:53 syslog: Connection Up. SNO/MAC/IP: [A502155D006292/C03E0F9F81C4/151.231.102.13]
Aug 9 01:51:41 syslog: Connection Up. SNO/MAC/IP: [A502155D006292/C03E0F9F81C4/151.231.102.13]
Aug 9 02:24:57 syslog: Connection Up. SNO/MAC/IP: [A502155D006292/C03E0F9F81C4/151.231.102.13]
Aug 9 02:54:57 syslog: Send out NTP request to ntp1.isp.sky.com
Aug 9 03:00:00 syslog: Connection Up. SNO/MAC/IP: [A502155D006292/C03E0F9F81C4/151.231.102.13]
Aug 9 03:32:58 syslog: Connection Up. SNO/MAC/IP: [A502155D006292/C03E0F9F81C4/151.231.102.13]
Aug 9 04:07:26 syslog: Connection Up. SNO/MAC/IP: [A502155D006292/C03E0F9F81C4/151.231.102.13]
Aug 9 04:39:12 syslog: Connection Up. SNO/MAC/IP: [A502155D006292/C03E0F9F81C4/151.231.102.13]
Aug 9 05:11:16 syslog: Connection Up. SNO/MAC/IP: [A502155D006292/C03E0F9F81C4/151.231.102.13]
Aug 9 05:37:04 syslog: Connection Up. SNO/MAC/IP: [A502155D006292/C03E0F9F81C4/151.231.102.13]
Aug 9 05:37:05 syslog: Send out NTP request to ntp1.isp.sky.com
Aug 9 06:01:57 syslog: Connection Up. SNO/MAC/IP: [A502155D006292/C03E0F9F81C4/151.231.102.13]
Aug 9 06:30:27 syslog: Connection Up. SNO/MAC/IP: [A502155D006292/C03E0F9F81C4/151.231.102.13]
Aug 9 06:54:27 syslog: Connection Up. SNO/MAC/IP: [A502155D006292/C03E0F9F81C4/151.231.102.13]
Aug 9 07:27:25 syslog: Connection Up. SNO/MAC/IP: [A502155D006292/C03E0F9F81C4/151.231.102.13]
Aug 9 08:01:35 syslog: Connection Up. SNO/MAC/IP: [A502155D006292/C03E0F9F81C4/151.231.102.13]
Aug 9 08:25:35 syslog: Send out NTP request to ntp1.isp.sky.com
Aug 9 08:28:51 syslog: Connection Up. SNO/MAC/IP: [A502155D006292/C03E0F9F81C4/151.231.102.13]
Aug 9 09:04:13 syslog: Connection Up. SNO/MAC/IP: [A502155D006292/C03E0F9F81C4/151.231.102.13]

How to Reset the Sata Link Controller for Full Sata 3 speeds on an OCZ Agility 3

So I purchased a new OCZ Agility 3 drive, installed it into the main bay of my 2012 Macbook Pro, and the drive was running at half speed. I called OCZ and spoke to the guys about how to resolve this issue, they were very knowledgeable, but they had no ideas how to make thier Linux Live Tool work on the Mac, which gives us the ability to reset the controller. Here's what I did to get the full speeds out of my OCZ Agility 3.
- You will need a Windows computer, or the ability to create and install Windows on a Bootcamp partition on your Mac.
- Thumb Drive
- Lots of Patience
1. Open Disk Utility and create one partition on your thumb drive under MS-DOS Fat 32. Click the Options tab and select “Master Boot Record.”
2. Go to the OCZ forum and download the older Linux Live Tool version: OCZ_Tools_316-old.zip. From my experience, the newer version doesn’t work on the 2012 Macbook Pro.
3.Download the “Universal USB Installer” for Windows, and follow the steps to install the ISO to your Thumb Drive using the instructions located on the OCZ Forum. http://www.ocztechnologyforum.com/forum/showthread.php?99275-NEW!-Bootable-Linux -based-tools-for-OCZ-SSD-s&p=714047&viewfull=1#post714047
4. Once the ISO is successfully copied to the Thumb Drive, insert the USB stick into your Mac with the OCZ SSD installed in the Main Bay, Power On, and hold down the “Option” key. You should see a yellow hard disk icon that says “Windows,” select it and press enter.
5. Once the OCZ Tool loads up, click the “Green Arrows” to put the drive into Sata II mode. Shutdown the computer, power on, and check the System Profiler. The drive should be running at Sata II speeds.
6. Shutdown the computer and boot into the OCZ Tool, and click on the “Red Arrows.” This will reset the controller to its default mode of Sata III (Sata 6 Mode).
7. Check the speed of the drive using the disk speed test of your choice. The drive should now be running at full speed.
The biggest accomplishment here was actually getting the OCZ Linux Live Tool to load on a 2012 Macbook Pro. The newer version of the tool doesnt support the USB 3.0 drivers, so you loose the funtion of your trackpad and keyboard or bluetooth keyboard and mouse.
**Note: Black Magic Disk Speed Test Version 2.0 may give you lower numbers than expected due to the compression method in testing the drive. I would prefer using XBench or Disk Speed Test Version 1.0**
***Here's a link to a thread that explains how to properly install your OS onto the drive. If not done correctly, this can also cripple the speed of the drive.***
Drive Preparation
https://discussions.apple.com/thread/3381208?start=0&tstart=0

I can almost see a big grin appearing in Bob's avatar...
Hopefully his reply has given you a clue already?
If not, some explanation:
Many settings in the standard "Media" panel (for both video and audio) don't apply for publications that need to go the Folio-way. This panel is mainly concerned with lovely Flash stuff, but apart from the Poster frame and the Markers, it is useless for Folio's.
A quick guide: create a video with the necessary codec (H.264 for video, MP# or AAC for audio) at the required pixel size (exact width/height). Simply Place the file in InDesign, but don't scale it (or recreate and place a properly sized new video afterwards). Choose what to do with the Poster frame (and maybe some Markers), but all other settings are done in the Overlay Creator.
Check Bob Bringhurst's Tutorials and his DPS Tips app for more info. But I guess you get the idea now.

ASA 5580 with EtherChannel 20Gbs, Does the Failover link must match the same Speed?

Hello,
I have an ASA 5580, I am plannning on setting two EtherChannels (inside and outside), each channel will include two TenGigabit interfaces.
My questions is that if the links that I am gonig to use for the failover and link, should also be 20Gbs each, or it is ok to use 10Gbs for each link?
According to the Configuration guide 8.4
Use the following failover interface speed guidelines for the ASAs:
• Cisco ASA 5510
– Stateful link speed can be 100 Mbps, even though the data interface can operate at 1 Gigabit due
to the CPU speed limitation.
• Cisco ASA 5520/5540/5550
– Stateful link speed should match the fastest data link.
• Cisco ASA 5580/5585
– Use only non-management 1 Gigabit ports for the stateful link because management ports have
lower performance and cannot meet the performance requirement for Stateful Failover.
Thanks in advance

Hi,
I have 2x ASA5580-20 with 8x1GE interfaces and additional 2x 10GE interfaces each. Software version running is v8.4.4.1.
I am planning to use them in multiple context (active/active) transparent mode. Taking into account the FW performance of 5Gbps real-world traffic per ASA5580-20, which on the following interface configurations would make the most sense?
Option 1:
2x10GE = 20GE Etherchannel for Data
1x1GE LAN Failover
1x1GE STATE Failover
Option 2:
1x 10GE Data
1x 10GE LAN & STATE Failover
Option 3:
2x10GE = 20GE Etherchannel for Data
4x1GE = 4GE Etherchannel for LAN/STATE Failover (possibly up to 8x1GE)
(etherchannel for LAN/STATE Failover actually does not make much sense, since only one interface wll be used anyway)
Option 4:
1x10GE LAN & STATE Failover
8x1GE = 8 GE Etherchannel for Data
I have read several guides (e.g. link1, link2, link3). Some state that 1GE Failover interfaces would suffice for the ASA5580, others recommend a link as fast as the data link. Almost none of them account for higher bandwidth etherchannels.
What is recommended in this case? Both Firewalls will be connected to one VSS Switch Pair, so it would make sense to cross-connect with at least 2 links on each VSS member.
The ASA does not support connecting an EtherChannel to a switch stack. If the ASA EtherChannel is connected cross stack, and if the Master switch is powered down, then the EtherChannel connected to the remaining switch will not come up. (http://www.cisco.com/en/US/docs/security/asa/asa84/configuration/guide/interface_start.html)
Thanks in advance for your feedback!

Video Conferencing over Low speed WAN links

Hi there,
Can somebody explain possible point-to-nultipoint video conferencing solution over low speed WAN links ?
( I have central site and about 20 remote sites - hub and spoke configuraition)
a. What is the minimum BW requirement
b. If using Cisco Video advantage at users desktop how do we select the proper MCU at the central site ?

Buffer 15 to 30 seconds. Make sure to tell them there will be
a long load time. There really isn't much you can do besides
that.

Output power dbm and low speeds?

Hello, I have been an Infinity 2 user for just over 2 years now and have seen significant decrease in speeds. In April 2013 I was syncing max speed with IP profile of 77.4mbps DL and 20 mbps UL. About a year later speeds dropped to about 55mbps DL and now I am getting about 28mbps DL.
Here are my current dsl stats:
Is my POWER Down lower than it should be? I have seen most people with a Power around 13-14 dbm. Is this affecting my MAX attainable rate? How is the Power controlled and can I increase it?
Here are my speedtest and adsl checker:
How did my connection degrade this much?
Solved!
Go to Solution.

Hi vinhphat168,
Thanks for posting, I'm sorry to see you're having problems with your connection speed. Please use the 'contact the mods' link in my forum profile to send in your details and we'll get this looked into. You can find the link by clicking on my username.
Thanks
Neil
BTCare Community Mod
If we have asked you to email us with your details, please make sure you are logged in to the forum, otherwise you will not be able to see our ‘Contact Us’ link within our profiles.
We are sorry but we are unable to deal with service/account queries via the private message(PM) function so please don't PM your account info, we need to deal with this via our email account :-)
If someone answers your question correctly please let other members know by clicking on ’Mark as Accepted Solution’.

Connection issues and low speeds

Hi there,
my family have been with BT now for about 3 or so years and the connection had been rather good until about late last year. According to my family it's everytime I come back home from uni the internet starts to play up as in:
. Low speeds
.Drops out and loses connection
Believing it was somehow my laptop causing the issues I backed everything up and completly wiped it because BT support thought it may be a virus on my machine even the the checks came back with nothing. So I've wiped my laptop and restarted it like it was a brand new laptop...still we're having these issues so I refuse to believe it's my laptop causing the problems. I've changed the chanel on the hub so many times it just doesn't make a difference. Tried different DSL adapters tried different cables even a wired connection causes problems. I am begining to think it's because the router has had it but I am willing to try anything at this point before asking for a new router from BT. Even BT don't seem to know what the problem is all they do is reset the routers chanel every single time I ring them.
So any advice or help would be greatly appreaciated
Many Thanks
Benjamin
PS - sorry for any grammar/spelling mistakes , I've written this in a hurry before the internet drops out again...

Hi Welcome to the community forums
Here is a basic guide to getting help from the community members done by CL Keith Please read through the link posted http://forumhelp.dyndns.info/speed/first_steps.html
once you have posted the information asked for then the community members can help you more
Thank You
This is a customer to customer self help forum the only BT presence here are the forum moderators
If you want to say thanks for a helpful answer,please click on the Ratings star on the left-hand side If the reply answers your question then please mark as ’Mark as Accepted Solution’

Very slow internet speed for the last few days

I don't know what happened but I'm experiencing low speeds when browsing the internet, to navigate this page it took me ages , this is my line status, anything wrong with it?
ADSL line status<script type="text/javascript"></script>
Connection information<script type="text/javascript"></script>
Line state
Connected
Connection time
0 days, 1:24:31
Downstream
575 Kbps
Upstream
828 Kbps
ADSL settings<script type="text/javascript"></script>
VPI/VCI
0/38
Type
PPPoA
Modulation
ITU-T G.992.5
Latency type
Interleaved
Noise margin (Down/Up)
35.5 dB / 9.6 dB
Line attenuation (Down/Up)
17.5 dB / 9.6 dB
Output power (Down/Up)
19.2 dBm / 12.4 dBm
Loss of Framing (Local)
0
Loss of Signal (Local)
0
Loss of Power (Local)
0
FEC Errors (Down/Up)
0 / 44
CRC Errors (Down/Up)
0 / 2147480000
HEC Errors (Down/Up)
nil / 721
Error Seconds (Local)
0

my speed keeps going down.
I had to swap my v2 hub to my old v1 hub because I've noticed the v2 keeps rebooting itself for no reason and it's really frustrating if I need to keep it on all the time as advised to get better profile
my questions are:
Why my old hub is more stable than the new one?
why my speed keeps dropping when my line is capable of 20mb and I achieved it after the engineer's visit last week but a couple of days after started to go down?
isn't it my upload speed to low?
this are my statistics:
Uptime:
0 days, 0:38:47
Modulation:
G.992.5 annex A
Bandwidth (Up/Down) [kbps/kbps]:
1,106 / 6,654
Data Transferred (Sent/Received) [MB/MB]:
9.08 / 55.28
Output Power (Up/Down) [dBm]:
12.5 / 20.0
Line Attenuation (Up/Down) [dB]:
9.0 / 21.5
SN Margin (Up/Down) [dB]:
5.5 / 27.0
Vendor ID (Local/Remote):
TMMB / TSTC
Loss of Framing (Local/Remote):
0 / 0
Loss of Signal (Local/Remote):
0 / 0
Loss of Power (Local/Remote):
0 / 0
Loss of Link (Remote):
0
Error Seconds (Local/Remote):
0 / 0
FEC Errors (Up/Down):
0 / 0
CRC Errors (Up/Down):
0 / 0
HEC Errors (Up/Down):
0 / 0
Line Profile:
Fast
this morning the speedtester said my Ip profile was 5500, a couple days ago was 13000, before that 19000
this is my last speedtest http://www.speedtest.net/result/955401239.png

Wifi speed and the new Apple TV concerns

One of the great things about my classic ATV is that I can start downloading a movie before dinner, and know that my viewing experience later won't be subject to variances in the wifi speed. In my experience, wifi speed and reliability can vary widely - and my worst nightmare is a video that stutters or freezes.
I new the new box has the faster modern chip, but I'm concerned Apple has no control over what might be the weak link: the wifi connection.
Is it time to make a run on a couple of classic boxes? Are they still in stock anywhere?

The problem is that all services are bundled with your Apple ID ([email protected]):
Your iCloud account (Mail, Contacts, Calendars, Reminders, Notes, Backups, etc.),
also iTunes & App Store purchases (Music, Movies, TV Shows, etc.),
and the iTunes Match services.
(I guess that all your devices - yours and your wife's are connected to one iTunes library, right?)
If you want that your wife gets her own iCloud account for Mail, Contacts, Calendars, etc. but gets also access to your media then you have two set up two things on her device:
iCloud (Settings > iCloud) with her account (e.g. [email protected])
and
iTunes & App Stores (Settings > iTunes & App Stores) with your account (e.g. [email protected]).
In this case she gets access to your library and could use the same iTunes Match account.
(See also: Using one Apple ID for iCloud and a different Apple ID for Store Purchases http://support.apple.com/kb/HT4895)

Reg:Low speed of the fibre link

Similar Messages

Maybe you are looking for