Reg. Translation
Hi
I just found that if I translated a flavour once, then to change small thing, I am not able to translate the same flavour again.
Hi,
In TRX BSP_WD_CMPWB go to the screen configuration and change the field name.
Best regards,
Caíque Escaler
Similar Messages
-
Calling issue with Cisco 7937 conference station
Hi Friends,
I am facing issue wiht Cisco 7937 conference station, our customer have various branch offices accross the world. All branches are connected over MPLS through service provider( SIP service provider) . there is a centralized CUCM and remote office have SIP Voice gateways .
When making calls from once remote site to another using Cisco 6921 phones calls working fine
When making calls from once remote site to another using Cisco 7937 conference station to make call any phone at remote office, calls are getting disconneted, remote phone rings when calls, but its gets fast busy tone when other party picks up the phone and not able to talk.
I suspect the issue with Codec but we have configured transcoders in VG and registered with CUCM
Please help me if any one experience such issue earlier.
Regards
Sivahi Basant,
1. Actually tow phones A and B are registerd with centralized CUCM, A and B are located in two different locations, RTP traffic between And B pass through service provider.
Call Flow --> Phone A ---->CUCMRouterpattern--> SIP trunk ----> Voice gateway--->Service provider cloud---> Respective Voice Gateway---> CUCM -- Phone B
Show Run
=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2014.02.27 15:14:52 =~=~=~=~=~=~=~=~=~=~=~=
sh run
Building configuration...
Current configuration : 12139 bytes
! Last configuration change at 06:35:59 UTC Tue Feb 25 2014
! NVRAM config last updated at 11:16:38 UTC Mon Feb 24 2014 by administrator
! NVRAM config last updated at 11:16:38 UTC Mon Feb 24 2014 by administrator
version 15.1
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname eucamvgw01
boot-start-marker
boot system flash:c2900-universalk9-mz.SPA.151-4.M5.bin
boot-end-marker
card type e1 0 0
logging buffered 51200 warnings
no logging console
no aaa new-model
no network-clock-participate wic 0
no ipv6 cef
ip source-route
ip traffic-export profile cuecapture mode capture
bidirectional
ip cef
ip multicast-routing
ip domain name drreddys.eu
ip name-server 10.197.20.1
ip name-server 10.197.20.2
multilink bundle-name authenticated
stcapp ccm-group 2
stcapp
stcapp feature access-code
stcapp feature speed-dial
stcapp supplementary-services
port 0/1/0
fallback-dn 5428025
port 0/1/1
fallback-dn 5428008
port 0/1/2
fallback-dn 5421462
port 0/1/3
fallback-dn 5421463
isdn switch-type primary-net5
crypto pki token default removal timeout 0
voice-card 0
dsp services dspfarm
voice call send-alert
voice call disc-pi-off
voice call convert-discpi-to-prog
voice rtp send-recv
voice service voip
ip address trusted list
ipv4 10.198.0.0 255.255.255.0
ipv4 152.63.1.0 255.255.255.0
address-hiding
allow-connections sip to sip
no supplementary-service h225-notify cid-update
no supplementary-service sip moved-temporarily
no supplementary-service sip refer
fax protocol t38 version 0 ls-redundancy 0 hs-redundancy 0 fallback none
fax-relay ans-disable
sip
rel1xx supported "track"
privacy pstn
no update-callerid
early-offer forced
call-route p-called-party-id
voice class uri 100 sip
host 41.206.187.71
voice class codec 10
codec preference 1 g711alaw
codec preference 2 g711ulaw
codec preference 3 ilbc
codec preference 4 g729r8
codec preference 5 g729br8
voice class codec 20
codec preference 1 g729br8
codec preference 2 g729r8
voice moh-group 1
moh flash:moh/Panjo.alaw.wav
description MOH G711 alaw
multicast moh 239.1.1.2 port 16384 route 10.198.2.9
voice translation-rule 1
rule 1 /^012237280\(..\)/ /54280\1/
rule 2 /^012236514\(..\)/ /54214\1/
rule 3 /^01223651081/ /5428010/
rule 4 /^01223506701/ /5428010/
voice translation-rule 2
rule 1 /^00\(.+\)/ /+\1/
rule 2 /^0\(.+\)/ /+44\1/
rule 3 /^\([0-9].+\)/ /+\1/
voice translation-rule 3
rule 1 /^9\(.+\)/ /\1/
rule 2 /^\+44\(.+\)/ /0\1/
rule 3 /^\+\(.+\)/ /00\1/
voice translation-rule 4
rule 1 /^54280\(..\)/ /12237280\1/
rule 2 /^54214\(..\)/ /12236514\1/
rule 3 /^\+44\(.+\)/ /\1/
rule 4 /^.54280\(..\)/ /12237280\1/
rule 5 /^.54214\(..\)/ /12236514\1/
voice translation-rule 9
rule 1 /^\(....\)/ /542\1/
voice translation-rule 10
voice translation-rule 11
rule 1 /^\+44122372\(....\)/ /542\1/
rule 2 /^\+44122365\(....\)/ /542\1/
voice translation-rule 12
voice translation-rule 13
rule 1 /^\([18]...\)/ /542\1/
voice translation-rule 14
voice translation-profile MPLS-incoming
translate calling 10
translate called 9
voice translation-profile MPLS-outgoing
translate calling 11
translate called 12
voice translation-profile PSTN-incoming
translate calling 2
translate called 1
voice translation-profile PSTN-outgoing
translate calling 4
translate called 3
voice translation-profile SRST-incoming
translate calling 14
translate called 13
license udi pid CISCO2921/K9 sn FGL145110RE
hw-module ism 0
hw-module pvdm 0/0
username administrator privilege 15 secret 5 $1$syu5$DsxdOgfS7Wltx78o4PV.60
redundancy
controller E1 0/0/0
ip tcp path-mtu-discovery
ip scp server enable
interface Embedded-Service-Engine0/0
no ip address
shutdown
interface GigabitEthernet0/0
description internal LAN
ip address 10.198.2.9 255.255.255.0
duplex auto
speed auto
interface ISM0/0
ip unnumbered GigabitEthernet0/0
service-module ip address 10.198.2.8 255.255.255.0
!Application: CUE Running on ISM
service-module ip default-gateway 10.198.2.9
interface GigabitEthernet0/1
description to TATA NGN
ip address 115.114.225.122 255.255.255.252
duplex auto
speed auto
interface GigabitEthernet0/2
description SIP Trunks external
ip address 79.121.254.83 255.255.255.248
ip access-group SIP-InBound in
ip traffic-export apply cuecapture size 8000000
duplex auto
speed auto
interface ISM0/1
description Internal switch interface connected to Internal Service Module
no ip address
shutdown
interface Vlan1
no ip address
ip forward-protocol nd
no ip http server
no ip http secure-server
ip route 0.0.0.0 0.0.0.0 10.198.2.1
ip route 10.198.2.8 255.255.255.255 ISM0/0
ip route 41.206.187.0 255.255.255.0 115.114.225.121
ip route 77.37.25.46 255.255.255.255 79.121.254.81
ip route 83.245.6.81 255.255.255.255 79.121.254.81
ip route 83.245.6.82 255.255.255.255 79.121.254.81
ip route 95.223.1.107 255.255.255.255 79.121.254.81
ip route 192.54.47.0 255.255.255.0 79.121.254.81
ip access-list extended SIP-InBound
permit ip host 77.37.25.46 any
permit ip host 83.245.6.81 any
permit ip host 83.245.6.82 any
permit ip 192.54.47.0 0.0.0.255 any
permit icmp any any
permit ip host 95.223.1.107 any
deny ip any any log
control-plane
voice-port 0/1/0
compand-type a-law
timeouts initial 60
timeouts interdigit 60
timeouts ringing infinity
caller-id enable
voice-port 0/1/1
compand-type a-law
timeouts initial 60
timeouts interdigit 60
timeouts ringing infinity
caller-id enable
voice-port 0/1/2
compand-type a-law
timeouts initial 60
timeouts interdigit 60
timeouts ringing infinity
caller-id enable
voice-port 0/1/3
compand-type a-law
timeouts initial 60
timeouts interdigit 60
timeouts ringing infinity
caller-id enable
no ccm-manager fax protocol cisco
ccm-manager music-on-hold bind GigabitEthernet0/0
ccm-manager config server 152.63.1.19 152.63.1.100 172.27.210.5
ccm-manager sccp local GigabitEthernet0/0
ccm-manager sccp
mgcp profile default
sccp local GigabitEthernet0/0
sccp ccm 10.198.2.9 identifier 3 priority 3 version 7.0
sccp ccm 152.63.1.19 identifier 4 version 7.0
sccp ccm 152.63.1.100 identifier 5 version 7.0
sccp ccm 172.27.210.5 identifier 6 version 7.0
sccp
sccp ccm group 2
bind interface GigabitEthernet0/0
associate ccm 4 priority 1
associate ccm 5 priority 2
associate ccm 6 priority 3
associate ccm 3 priority 4
associate profile 1002 register CFB_UK_CAM_02
associate profile 1001 register XCODE_UK_CAM_02
associate profile 1000 register MTP_UK_CAM_02
dspfarm profile 1001 transcode
codec ilbc
codec g722-64
codec g729br8
codec g729r8
codec gsmamr-nb
codec pass-through
codec g711ulaw
codec g711alaw
codec g729ar8
codec g729abr8
maximum sessions 18
associate application SCCP
dspfarm profile 1002 conference
codec g711ulaw
codec g711alaw
codec g729ar8
codec g729abr8
codec g729r8
codec g729br8
maximum sessions 2
associate application SCCP
dspfarm profile 1000 mtp
codec g711alaw
maximum sessions software 200
associate application SCCP
dial-peer cor custom
name SRSTMode
dial-peer cor list SRST
member SRSTMode
dial-peer voice 100 voip
description *** Inbound CUCM ***
translation-profile incoming PSTN-incoming
incoming called-number .
voice-class codec 10
voice-class sip call-route p-called-party-id
dtmf-relay rtp-nte
no vad
dial-peer voice 500 voip
description *** Inbound TATA MPLS ***
translation-profile incoming MPLS-incoming
session protocol sipv2
session target sip-server
incoming called-number ....
incoming uri from 100
voice-class codec 20
dtmf-relay rtp-nte
no vad
dial-peer voice 510 voip
description *** Outbound TATA MPLS ***
translation-profile outgoing MPLS-outgoing
destination-pattern 54[013-9]....
session protocol sipv2
session target ipv4:41.206.187.71
session transport udp
voice-class codec 20
dtmf-relay rtp-nte
no vad
dial-peer voice 520 voip
description *** Outbound TATA MPLS ***
translation-profile outgoing MPLS-outgoing
destination-pattern 5[0-35-9].....
session protocol sipv2
session target ipv4:41.206.187.71
session transport udp
voice-class codec 20
dtmf-relay rtp-nte
no vad
dial-peer voice 200 voip
description *** Inbound M12 *** 01223651081, 01223651440 - 01223651489
translation-profile incoming PSTN-incoming
session protocol sipv2
session target sip-server
session transport udp
incoming called-number 0122365....
dtmf-relay rtp-nte
codec g711ulaw
no vad
dial-peer voice 201 voip
description *** Inbound M12 *** 012237280XX
translation-profile incoming PSTN-incoming
session protocol sipv2
session target sip-server
session transport udp
incoming called-number 012237280..
dtmf-relay rtp-nte
codec g711ulaw
no vad
dial-peer voice 202 voip
description *** Inbound M12 *** 01223506701
translation-profile incoming PSTN-incoming
session protocol sipv2
session target sip-server
session transport udp
incoming called-number 01223506701
dtmf-relay rtp-nte
codec g711ulaw
no vad
dial-peer voice 210 voip
description *** Outbound M12 ***
translation-profile outgoing PSTN-outgoing
destination-pattern +...T
session protocol sipv2
session target ipv4:83.245.6.81
session transport udp
dtmf-relay rtp-nte
codec g711alaw
no vad
dial-peer voice 211 voip
description *** Outbound ISDN for SRST and emergency ***
translation-profile outgoing PSTN-outgoing
destination-pattern 9.T
session protocol sipv2
session target ipv4:83.245.6.81
session transport udp
dtmf-relay rtp-nte
codec g711alaw
no vad
dial-peer voice 212 voip
description *** Outbound ISDN for emergency ***
translation-profile outgoing PSTN-outgoing
destination-pattern 11[02]
session protocol sipv2
session target ipv4:83.245.6.81
session transport udp
dtmf-relay rtp-nte
codec g711alaw
no vad
dial-peer voice 2000 voip
description *** Outbound to CUCM Primary ***
preference 1
destination-pattern 542....
session protocol sipv2
session target ipv4:152.63.1.19
voice-class codec 10
voice-class sip call-route p-called-party-id
dtmf-relay rtp-nte
no vad
dial-peer voice 2001 voip
description *** Outbound to CUCM Secondary ***
preference 2
destination-pattern 542....
session protocol sipv2
session target ipv4:152.63.1.100
voice-class codec 10
voice-class sip call-route p-called-party-id
dtmf-relay rtp-nte
no vad
dial-peer voice 2002 voip
description *** Outbound to CUCM Teritiary ***
preference 3
destination-pattern 542....
session protocol sipv2
session target ipv4:172.27.210.5
voice-class codec 10
voice-class sip call-route p-called-party-id
dtmf-relay rtp-nte
no vad
dial-peer voice 999010 pots
service stcapp
port 0/1/0
dial-peer voice 999011 pots
service stcapp
port 0/1/1
dial-peer voice 999012 pots
service stcapp
port 0/1/2
dial-peer voice 999013 pots
service stcapp
port 0/1/3
sip-ua
no remote-party-id
gatekeeper
shutdown
call-manager-fallback
secondary-dialtone 9
max-conferences 4 gain -6
transfer-system full-consult
ip source-address 10.198.2.9 port 2000
max-ephones 110
max-dn 400 dual-line no-reg
translation-profile incoming SRST-incoming
moh flash:/moh/Panjo.ulaw.wav
multicast moh 239.1.1.1 port 16384 route 10.198.2.9
time-zone 22
time-format 24
date-format dd-mm-yy
line con 0
login local
line aux 0
line 2
no activation-character
no exec
transport preferred none
transport input all
transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
stopbits 1
line 131
no activation-character
no exec
transport preferred none
transport input all
transport output pad telnet rlogin lapb-ta mop udptn v120 ssh
stopbits 1
line vty 0 4
session-timeout 60
exec-timeout 60 0
privilege level 15
login local
transport input all
line vty 5 15
session-timeout 60
exec-timeout 60 0
privilege level 15
login local
transport input all
scheduler allocate 20000 1000
ntp server 10.1.30.1
end
eucamvgw01#
Sh SCCP
=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2014.03.03 17:57:44 =~=~=~=~=~=~=~=~=~=~=~=
SCCP Admin State: UP
Gateway Local Interface: GigabitEthernet0/0
IPv4 Address: 10.198.2.9
Port Number: 2000
IP Precedence: 5
User Masked Codec list: None
Call Manager: 10.198.2.9, Port Number: 2000
Priority: 3, Version: 7.0, Identifier: 3
Call Manager: 152.63.1.19, Port Number: 2000
Priority: N/A, Version: 7.0, Identifier: 4
Trustpoint: N/A
Call Manager: 152.63.1.100, Port Number: 2000
Priority: N/A, Version: 7.0, Identifier: 5
Trustpoint: N/A
Call Manager: 172.27.210.5, Port Number: 2000
Priority: N/A, Version: 7.0, Identifier: 6
Trustpoint: N/A
MTP Oper State: ACTIVE - Cause Code: NONE
Active Call Manager: 152.63.1.19, Port Number: 2000
TCP Link Status: CONNECTED, Profile Identifier: 1000
Reported Max Streams: 400, Reported Max OOS Streams: 0
Supported Codec: g711alaw, Maximum Packetization Period: 30
Supported Codec: rfc2833 dtmf, Maximum Packetization Period: 30
Supported Codec: rfc2833 pass-thru, Maximum Packetization Period: 30
Supported Codec: inband-dtmf to rfc2833 conversion, Maximum Packetization Period: 30
TLS : ENABLED
Transcoding Oper State: ACTIVE - Cause Code: NONE
Active Call Manager: 152.63.1.19, Port Number: 2000
TCP Link Status: CONNECTED, Profile Identifier: 1001
Reported Max Streams: 36, Reported Max OOS Streams: 0
Supported Codec: ilbc, Maximum Packetization Period: 120
Supported Codec: g722r64, Maximum Packetization Period: 30
Supported Codec: g729br8, Maximum Packetization Period: 60
Supported Codec: g729r8, Maximum Packetization Period: 60
Supported Codec: gsmamr-nb, Maximum Packetization Period: 60
Supported Codec: pass-thru, Maximum Packetization Period: N/A
Supported Codec: g711ulaw, Maximum Packetization Period: 30
Supported Codec: g711alaw, Maximum Packetization Period: 30
Supported Codec: g729ar8, Maximum Packetization Period: 60
Supported Codec: g729abr8, Maximum Packetization Period: 60
Supported Codec: rfc2833 dtmf, Maximum Packetization Period: 30
Supported Codec: rfc2833 pass-thru, Maximum Packetization Period: 30
Supported Codec: inband-dtmf to rfc2833 conversion, Maximum Packetization Period: 30
Conferencing Oper State: ACTIVE - Cause Code: NONE
Active Call Manager: 152.63.1.19, Port Number: 2000
TCP Link Status: CONNECTED, Profile Identifier: 1002
Reported Max Streams: 16, Reported Max OOS Streams: 0
Supported Codec: g711ulaw, Maximum Packetization Period: 30
Supported Codec: g711alaw, Maximum Packetization Period: 30
Supported Codec: g729ar8, Maximum Packetization Period: 60
Supported Codec: g729abr8, Maximum Packetization Period: 60
Supported Codec: g729r8, Maximum Packetization Period: 60
Supported Codec: g729br8, Maximum Packetization Period: 60
Supported Codec: rfc2833 dtmf, Maximum Packetization Period: 30
Supported Codec: rfc2833 pass-thru, Maximum Packetization Period: 30
Supported Codec: inband-dtmf to rfc2833 conversion, Maximum Packetization Period: 30
TLS : ENABLED
Alg_Phone Oper State: ACTIVE - Cause Code: NONE
Active Call Manager: 152.63.1.19, Port Number: 2000
TCP Link Status: CONNECTED, Device Name: AN71FEF7F070080
Reported Max Streams: 1, Reported Max OOS Streams: 0
Supported Codec: rfc2833 dtmf, Maximum Packetization Period: 30
Supported Codec: g711ulaw, Maximum Packetization Period: 20
Supported Codec: g711alaw, Maximum Packetization Period: 20
Supported Codec: g729r8, Maximum Packetization Period: 220Supported Codec: g729ar8, Maximum Packetization Period: 220
Supported Codec: g729br8, Maximum Packetization Period: 220
Supported Codec: g729r8, Maximum Packetization Period: 220
Supported Codec: ilbc, Maximum Packetization Period: 120
Alg_Phone Oper State: ACTIVE - Cause Code: NONE
Active Call Manager: 152.63.1.19, Port Number: 2000
TCP Link Status: CONNECTED, Device Name: AN71FEF7F070081
Reported Max Streams: 1, Reported Max OOS Streams: 0
Supported Codec: rfc2833 dtmf, Maximum Packetization Period: 30
Supported Codec: g711ulaw, Maximum Packetization Period: 20
Supported Codec: g711alaw, Maximum Packetization Period: 20
Supported Codec: g729r8, Maximum Packetization Period: 220
Supported Codec: g729ar8, Maximum Packetization Period: 220
Supported Codec: g729br8, Maximum Packetization Period: 220
Supported Codec: g729r8, Maximum Packetization Period: 220
Supported Codec: ilbc, Maximum Packetization Period: 120
Alg_Phone Oper State: ACTIVE - Cause Code: NONE
Active Call Manager: 152.63.1.19, Port Number: 2000
TCP Link Status: CONNECTED, Device Name: AN71FEF7F070082
Reported Max Streams: 1, Reported Max OOS Streams: 0
Supported Codec: rfc2833 dtmf, Maximum Packetization Period: 30
Supported Codec: g711ulaw, Maximum Packetization Period: 20Supported Codec: g711alaw, Maximum Packetization Period: 20
Supported Codec: g729r8, Maximum Packetization Period: 220
Supported Codec: g729ar8, Maximum Packetization Period: 220
Supported Codec: g729br8, Maximum Packetization Period: 220
Supported Codec: g729r8, Maximum Packetization Period: 220
Supported Codec: ilbc, Maximum Packetization Period: 120
Alg_Phone Oper State: ACTIVE - Cause Code: NONE
Active Call Manager: 152.63.1.19, Port Number: 2000
TCP Link Status: CONNECTED, Device Name: AN71FEF7F070083
Reported Max Streams: 1, Reported Max OOS Streams: 0
Supported Codec: rfc2833 dtmf, Maximum Packetization Period: 30
Supported Codec: g711ulaw, Maximum Packetization Period: 20
Supported Codec: g711alaw, Maximum Packetization Period: 20
Supported Codec: g729r8, Maximum Packetization Period: 220
Supported Codec: g729ar8, Maximum Packetization Period: 220
Supported Codec: g729br8, Maximum Packetization Period: 220
Supported Codec: g729r8, Maximum Packetization Period: 220
Supported Codec: ilbc, Maximum Packetization Period: 120
eucamvgw01# -
Reg. Translation of Program Documentation from German to English
Dear Experts,
Kindly help me in translating the Program Documentation from German to English version. I have searched the Previous Posts in Forum but still i am not able to find the right post.
Regards,
Ramesh ManoharanHi Ramesh,
To change the original language of an ABAP you need to copy it from the original into one development class - perhaps local - and then change the development class. When you go into edit the ABAP, you have the option of changing the original language. However, I can't find anything similar for the program documentation! As a workaround, you can use SE63 to modify the translation of the documentation for your copy.
Reddy -
Hi,
In our smartform we are trying to print this French text mise en uvre , but Adobe is having problem in reading this special character " ", so it prints as # .
Please suggest some solution to overcome this .
Thanks & Regards,
Keerthi vasan.M
Edited by: keerthi vasan on Mar 17, 2008 10:34 AMhow it is done please explain
I have got the same problem -
Dear Experts,
I have developed a report in ENGLISH. My selection screen contains 5 Fields.Material Number,X-dist.-material Status,costing source,MRF document status.By using i have converted into languages DE and FR.When i execute the program log on as DE then the selection screen texts except material number the others are not coming in german.
If anybody knows pls. help on this.
Thanks in advance,
Thanks and Regards,Hi,
Goto Tcode se63 and tranport the selection screen to other languages.
Regards,
Ram
Reward points if helpful -
Hi all,
I have a requirement of converting document currency to local currency for AR amount in the report
For this i have created a currency conversiontype by assigning 0loc_currcy in currency tab in Infoobject for determining target currency and assigned to the keyfigure in query.
when i execute the report it is not able to find all the local currencies
iam getting the error as below
WNo exchange rate from AED to and date 01/01/2009 found (currency transl. BRAIN 380AED
Can anyone tell me what would the problem.
Points wil be awarded.
Thanks in advanceHi Pathak,
Even when i execute the report for 01.01.2010...iam getting the same error as below
WNo exchange rate from AED to and date 01/01/2010 found (currency transl. BRAIN 380AED
but in OB08 the date is maintained as told above 31.05.2010.
Can you please tell me what would be the problem -
Regarding translations in scripts
Hi All,
I am facing a problem while translating a script from EN lang to say FR lang in se76 T-code.
In the main window, there are many elements to be translated and each element will have its own texts to be translated. During translation, we get the english text in teh non editable mode and the text that is to be translated into other lang in editable mode.
All the elements are getting translated except one Element. I am not able to understnad why that particular element is not getting translated. The editable window for that particular element is not getting displayed even when i want to translate it.
Can anybody help me out reg this problem. I want to translate the text presen tin taht particular element whichis not happening.. Pl let m e know what the problem might be and the solution to this as this is v important...
Regards,
PriyaHey bharath,
Thanks for the reply. But, can uplz help me out in doing the translation using se63 in ECC6.0? I had tried it out but as i could not know how to proceed with, i started translating it using se76.
Can u plz let me know the same process using se63 in 6.0?
Regards,
Priya -
Trouble with international translation
Hello all,
I'm having a problem getting international calls to complete. I have the below in my Cisco 5350 configs with some lines removed to save space. Debug is below that. It appears my translation rule is ok to some extent as the test indicates. What am I overlooking? Any help will be greatly appreciated.
Sprint5350#test voice translation-rule 2 011862196990
Matched with rule 1
Original number: 011862196990 Translated number: 0111862196990
Original number type: none Translated number type: none
Original number plan: none Translated number plan: none
voice translation-rule 1
rule 1 /\+1\(.*\)/ /\1/
voice translation-rule 2
rule 1 /^01/ /011/
voice translation-profile Incoming_Calling_Party_Num
translate calling 1
voice translation-profile outgoing_international
translate calling 2
translate called 2
controller T3 3/0
framing m23
clock source line
cablelength 133
t1 1-7 controller
description Sprint DS3 - 75955030
controller T1 3/0:1
framing esf
pri-group timeslots 1-24 nfas_d primary nfas_int 0 nfas_group 1
controller T1 3/0:2
framing esf
pri-group timeslots 1-24 nfas_d none nfas_int 2 nfas_group 1
controller T1 3/0:3
framing esf
pri-group timeslots 1-24 nfas_d backup nfas_int 1 nfas_group 1
controller T1 3/0:4
framing esf
pri-group timeslots 1-24 nfas_d none nfas_int 3 nfas_group 1
controller T1 3/0:5
framing esf
pri-group timeslots 1-24 nfas_d none nfas_int 4 nfas_group 1
controller T1 3/0:6
framing esf
pri-group timeslots 1-24 nfas_d none nfas_int 5 nfas_group 1
controller T1 3/0:7
framing esf
pri-group timeslots 1-24 nfas_d none nfas_int 6 nfas_group 1
interface Serial3/0:1:23
no ip address
encapsulation hdlc
isdn switch-type primary-4ess
no cdp enable
dial-peer voice 150 pots
translation-profile incoming Calling_Party_Num
translation-profile outgoing outgoing_international
destination-pattern 011.T
translate-outgoing called 1
direct-inward-dial
port 3/0:1:D
forward-digits 0
dial-peer voice 100 voip
preference 1
modem passthrough nse codec g711ulaw redundancy
voice-class codec 1
incoming called-number 800.......
dtmf-relay rtp-nte
fax protocol t38 ls-redundancy 0 hs-redundancy 0 fallback pass-through g711ulaw
no vad
*Sep 4 17:57:57.433: ISDN Se3/0:1:23 Q931: RX <- SERVICE pd = 3 callref = 0x0000
Change Status i = 0xC0 - in-service
Channel ID i = 0xE9818398
Exclusive, Interface 1, Channel 24
*Sep 4 17:57:59.001: //-1/BC10816380D4/RXRULE/regxrule_stack_pop_RegXruleNumInfo: stack=0x6871D9EC; count=1
*Sep 4 17:57:59.001: //-1/BC10816380D4/RXRULE/regxrule_get_profile_from_dialpeer_internal: Error: Invalid input peer_tag=0 direction=incom ing
*Sep 4 17:57:59.001: //-1/BC10816380D4/RXRULE/regxrule_stack_push_RegXruleNumInfo: stack=0x6871D9EC; count=0
*Sep 4 17:57:59.001: //-1/BC10816380D4/RXRULE/regxrule_stack_push_RegXruleNumInfo: stack=0x6871D9EC; count=1
*Sep 4 17:57:59.001: //-1/BC10816380D4/RXRULE/regxrule_profile_translate_internal: number=5024101498 type=unknown plan=unknown numbertype= calling
*Sep 4 17:57:59.001: //-1/BC10816380D4/RXRULE/regxrule_match: No match; number=5024101498 rule precedence=1
*Sep 4 17:57:59.001: //-1/BC10816380D4/RXRULE/regxrule_profile_match_internal: No match found
*Sep 4 17:57:59.001: //-1/BC10816380D4/RXRULE/regxrule_profile_translate_internal: No match: number=5024101498 type=unknown plan=unknown
*Sep 4 17:57:59.001: //-1/BC10816380D4/RXRULE/regxrule_profile_translate_internal: number=011862196990 type=unknown plan=unknown numbertyp e=called
*Sep 4 17:57:59.001: //-1/BC10816380D4/RXRULE/regxrule_profile_match_internal: Matched with rule 1 in ruleset 2
*Sep 4 17:57:59.001: //-1/BC10816380D4/RXRULE/regxrule_profile_match_internal: Matched with rule 1 in ruleset 2
*Sep 4 17:57:59.001: //-1/BC10816380D4/RXRULE/sed_subst: Successful substitution; pattern=011862196990 matchPattern=^01 replacePattern=011 replaced pattern=0111862196990
*Sep 4 17:57:59.001: //-1/BC10816380D4/RXRULE/regxrule_subst_num_type: Match Type = none, Replace Type = none Input Type = unknown
*Sep 4 17:57:59.001: //-1/BC10816380D4/RXRULE/regxrule_subst_num_plan: Match Plan = none, Replace Plan = none Input Plan = unknown
*Sep 4 17:57:59.001: //-1/BC10816380D4/RXRULE/regxrule_profile_translate_internal: xlt_number=0111862196990 xlt_type=unknown xlt_plan=unkn own
*Sep 4 17:57:59.001: //-1/BC10816380D4/RXRULE/regxrule_profile_translate_internal: number= type=unknown plan=unknown numbertype=redirect-t arget
*Sep 4 17:57:59.001: //-1/BC10816380D4/RXRULE/regxrule_get_RegXrule: Invalid translation ruleset tag=0
*Sep 4 17:57:59.001: //-1/BC10816380D4/RXRULE/regxrule_profile_match_internal: Error: ruleset for redirect-target number not found
*Sep 4 17:57:59.001: //-1/BC10816380D4/RXRULE/regxrule_profile_translate_internal: No match: number= type=unknown plan=unknown
*Sep 4 17:57:59.001: //-1/BC10816380D4/RXRULE/regxrule_profile_translate_internal: number= type=unknown plan=unknown numbertype=redirect-c alled
*Sep 4 17:57:59.001: //-1/BC10816380D4/RXRULE/regxrule_get_RegXrule: Invalid translation ruleset tag=0
*Sep 4 17:57:59.001: //-1/BC10816380D4/RXRULE/regxrule_profile_match_internal: Error: ruleset for redirect-called number not found
*Sep 4 17:57:59.001: //-1/BC10816380D4/RXRULE/regxrule_profile_translate_internal: No match: number= type=unknown plan=unknown
*Sep 4 17:57:59.001: //-1/BC10816380D4/RXRULE/regxrule_dp_translate: calling_number=5024101498 calling_octet=0x0
called_number=0111862196990 called_octet=0x0
redirect_number= redirect_type=0 redirect_plan=0 redirect_PI=-1 redirect_SI=-1
*Sep 4 17:57:59.005: //-1/BC10816380D4/RXRULE/regxrule_vp_translate: No profile found in voice port or trunk group for outgoing direction
*Sep 4 17:57:59.005: //-1/BC10816380D4/RXRULE/regxrule_vp_translate: calling_number=5024101498 calling_octet=0x0
called_number=0111862196990 called_octet=0x0
redirect_number= redirect_type=0 redirect_plan=0
*Sep 4 17:57:59.005: ISDN Se3/0:1:23 Q931: Applying typeplan for sw-type 0x2 is 0x2 0x1, Calling num 5024101498
*Sep 4 17:57:59.005: ISDN Se3/0:1:23 Q931: Applying typeplan for sw-type 0x2 is 0x2 0x1, Called num
*Sep 4 17:57:59.005: ISDN Se3/0:1:23 Q931: TX -> SETUP pd = 8 callref = 0x008E
Bearer Capability i = 0x8090A2
Standard = CCITT
Transfer Capability = Speech
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0xE9868398
Exclusive, Interface 6, Channel 24
Calling Party Number i = 0x2180, '5024101498'
Plan:ISDN, Type:National
Called Party Number i = 0xA1
Plan:ISDN, Type:National
*Sep 4 17:57:59.133: ISDN Se3/0:1:23 Q931: RX <- RELEASE_COMP pd = 8 callref = 0x808E
Cause i = 0x819C - Invalid number format (incomplete number)
*Sep 4 17:57:59.133: ISDN Se3/0:1:23 **ERROR**: call_cleared: VOICE ERROR: NULL VDEV Common(0xFC): bchan -1, call id 0x8016
*Sep 4 17:57:59.141: //-1/BC10816380D4/RXRULE/regxrule_stack_pop_RegXruleNumInfo: stack=0x6871D9EC; count=2
VoiceEncapPeer150
peer type = voice, system default peer = FALSE, information type = voice,
description = `',
tag = 150, destination-pattern = `011.T',
voice reg type = 0, corresponding tag = 0,
allow watch = FALSE
answer-address = `', preference=0,
CLID Restriction = None
CLID Network Number = `'
CLID Second Number sent
CLID Override RDNIS = disabled,
source carrier-id = `', target carrier-id = `',
source trunk-group-label = `', target trunk-group-label = `',
numbering Type = `unknown'
group = 150, Admin state is up, Operation state is up,
Outbound state is up,
incoming called-number = `', connections/maximum = 0/unlimited,
DTMF Relay = disabled,
URI classes:
Destination =
huntstop = disabled,
in bound application associated: 'DEFAULT'
out bound application associated: ''
dnis-map =
permission :both
incoming COR list:maximum capability
outgoing COR list:minimum requirement
Translation profile (Incoming):Calling_Party_Num
Translation profile (Outgoing):outgoing_international
incoming call blocking:
translation-profile = `'
disconnect-cause = `no-service'
advertise 0x40 capacity_update_timer 25 addrFamily 4 oldAddrFamily 4
type = pots, prefix = `',
forward-digits 0
session-target = `', voice-port = `3/0:1:D',
direct-inward-dial = enabled,
digit_strip = enabled,
register E.164 number with H323 GK and/or SIP Registrar = TRUE
fax rate = system, payload size = 20 bytes
supported-language = ''
preemption level = `routine'
bandwidth:
maximum = 64 KBits/sec, minimum = 64 KBits/sec
voice class called-number:
inbound = `', outbound = `'
dial tone generation after remote onhook = enabled
Time elapsed since last clearing of voice call statistics never
Connect Time = 0, Charged Units = 0,
Successful Calls = 0, Failed Calls = 15, Incomplete Calls = 0
Accepted Calls = 0, Refused Calls = 0,
Last Disconnect Cause is "1C ",
Last Disconnect Text is "invalid number (28)",
Last Setup Time = 50369257.
Last Disconnect Time = 0.
T1 3/0:1 is up.
Applique type is Channelized T1
No alarms detected.
alarm-trigger is not set
Soaking time: 3, Clearance time: 10
AIS State:Clear LOS State:Clear LOF State:Clear
Version info of slot 3: HW: 1536, PLD Rev: 6
Framer Version: 0x58
Manufacture Cookie Info:
EEPROM Type 0x0001, EEPROM Version 0x04, Board ID 0x01,
Board Hardware Version 6.0, Item Number 73-4089-07,
Board Revision A0, Serial Number JAE08512FBJ,
PLD/ISP Version 48.53, Manufacture Date 13-Dec-2004.Hello all,
I'm having a problem getting international calls to complete. I have the below in my Cisco 5350 configs with some lines removed to save space. Debug is below that. It appears my translation rule is ok to some extent as the test indicates. What am I overlooking? Any help will be greatly appreciated.
Sprint5350#test voice translation-rule 2 011862196990
Matched with rule 1
Original number: 011862196990 Translated number: 0111862196990
Original number type: none Translated number type: none
Original number plan: none Translated number plan: none
voice translation-rule 1
rule 1 /\+1\(.*\)/ /\1/
voice translation-rule 2
rule 1 /^01/ /011/
voice translation-profile Incoming_Calling_Party_Num
translate calling 1
voice translation-profile outgoing_international
translate calling 2
translate called 2
controller T3 3/0
framing m23
clock source line
cablelength 133
t1 1-7 controller
description Sprint DS3 - 75955030
controller T1 3/0:1
framing esf
pri-group timeslots 1-24 nfas_d primary nfas_int 0 nfas_group 1
controller T1 3/0:2
framing esf
pri-group timeslots 1-24 nfas_d none nfas_int 2 nfas_group 1
controller T1 3/0:3
framing esf
pri-group timeslots 1-24 nfas_d backup nfas_int 1 nfas_group 1
controller T1 3/0:4
framing esf
pri-group timeslots 1-24 nfas_d none nfas_int 3 nfas_group 1
controller T1 3/0:5
framing esf
pri-group timeslots 1-24 nfas_d none nfas_int 4 nfas_group 1
controller T1 3/0:6
framing esf
pri-group timeslots 1-24 nfas_d none nfas_int 5 nfas_group 1
controller T1 3/0:7
framing esf
pri-group timeslots 1-24 nfas_d none nfas_int 6 nfas_group 1
interface Serial3/0:1:23
no ip address
encapsulation hdlc
isdn switch-type primary-4ess
no cdp enable
dial-peer voice 150 pots
translation-profile incoming Calling_Party_Num
translation-profile outgoing outgoing_international
destination-pattern 011.T
translate-outgoing called 1
direct-inward-dial
port 3/0:1:D
forward-digits 0
dial-peer voice 100 voip
preference 1
modem passthrough nse codec g711ulaw redundancy
voice-class codec 1
incoming called-number 800.......
dtmf-relay rtp-nte
fax protocol t38 ls-redundancy 0 hs-redundancy 0 fallback pass-through g711ulaw
no vad
*Sep 4 17:57:57.433: ISDN Se3/0:1:23 Q931: RX <- SERVICE pd = 3 callref = 0x0000
Change Status i = 0xC0 - in-service
Channel ID i = 0xE9818398
Exclusive, Interface 1, Channel 24
*Sep 4 17:57:59.001: //-1/BC10816380D4/RXRULE/regxrule_stack_pop_RegXruleNumInfo: stack=0x6871D9EC; count=1
*Sep 4 17:57:59.001: //-1/BC10816380D4/RXRULE/regxrule_get_profile_from_dialpeer_internal: Error: Invalid input peer_tag=0 direction=incom ing
*Sep 4 17:57:59.001: //-1/BC10816380D4/RXRULE/regxrule_stack_push_RegXruleNumInfo: stack=0x6871D9EC; count=0
*Sep 4 17:57:59.001: //-1/BC10816380D4/RXRULE/regxrule_stack_push_RegXruleNumInfo: stack=0x6871D9EC; count=1
*Sep 4 17:57:59.001: //-1/BC10816380D4/RXRULE/regxrule_profile_translate_internal: number=5024101498 type=unknown plan=unknown numbertype= calling
*Sep 4 17:57:59.001: //-1/BC10816380D4/RXRULE/regxrule_match: No match; number=5024101498 rule precedence=1
*Sep 4 17:57:59.001: //-1/BC10816380D4/RXRULE/regxrule_profile_match_internal: No match found
*Sep 4 17:57:59.001: //-1/BC10816380D4/RXRULE/regxrule_profile_translate_internal: No match: number=5024101498 type=unknown plan=unknown
*Sep 4 17:57:59.001: //-1/BC10816380D4/RXRULE/regxrule_profile_translate_internal: number=011862196990 type=unknown plan=unknown numbertyp e=called
*Sep 4 17:57:59.001: //-1/BC10816380D4/RXRULE/regxrule_profile_match_internal: Matched with rule 1 in ruleset 2
*Sep 4 17:57:59.001: //-1/BC10816380D4/RXRULE/regxrule_profile_match_internal: Matched with rule 1 in ruleset 2
*Sep 4 17:57:59.001: //-1/BC10816380D4/RXRULE/sed_subst: Successful substitution; pattern=011862196990 matchPattern=^01 replacePattern=011 replaced pattern=0111862196990
*Sep 4 17:57:59.001: //-1/BC10816380D4/RXRULE/regxrule_subst_num_type: Match Type = none, Replace Type = none Input Type = unknown
*Sep 4 17:57:59.001: //-1/BC10816380D4/RXRULE/regxrule_subst_num_plan: Match Plan = none, Replace Plan = none Input Plan = unknown
*Sep 4 17:57:59.001: //-1/BC10816380D4/RXRULE/regxrule_profile_translate_internal: xlt_number=0111862196990 xlt_type=unknown xlt_plan=unkn own
*Sep 4 17:57:59.001: //-1/BC10816380D4/RXRULE/regxrule_profile_translate_internal: number= type=unknown plan=unknown numbertype=redirect-t arget
*Sep 4 17:57:59.001: //-1/BC10816380D4/RXRULE/regxrule_get_RegXrule: Invalid translation ruleset tag=0
*Sep 4 17:57:59.001: //-1/BC10816380D4/RXRULE/regxrule_profile_match_internal: Error: ruleset for redirect-target number not found
*Sep 4 17:57:59.001: //-1/BC10816380D4/RXRULE/regxrule_profile_translate_internal: No match: number= type=unknown plan=unknown
*Sep 4 17:57:59.001: //-1/BC10816380D4/RXRULE/regxrule_profile_translate_internal: number= type=unknown plan=unknown numbertype=redirect-c alled
*Sep 4 17:57:59.001: //-1/BC10816380D4/RXRULE/regxrule_get_RegXrule: Invalid translation ruleset tag=0
*Sep 4 17:57:59.001: //-1/BC10816380D4/RXRULE/regxrule_profile_match_internal: Error: ruleset for redirect-called number not found
*Sep 4 17:57:59.001: //-1/BC10816380D4/RXRULE/regxrule_profile_translate_internal: No match: number= type=unknown plan=unknown
*Sep 4 17:57:59.001: //-1/BC10816380D4/RXRULE/regxrule_dp_translate: calling_number=5024101498 calling_octet=0x0
called_number=0111862196990 called_octet=0x0
redirect_number= redirect_type=0 redirect_plan=0 redirect_PI=-1 redirect_SI=-1
*Sep 4 17:57:59.005: //-1/BC10816380D4/RXRULE/regxrule_vp_translate: No profile found in voice port or trunk group for outgoing direction
*Sep 4 17:57:59.005: //-1/BC10816380D4/RXRULE/regxrule_vp_translate: calling_number=5024101498 calling_octet=0x0
called_number=0111862196990 called_octet=0x0
redirect_number= redirect_type=0 redirect_plan=0
*Sep 4 17:57:59.005: ISDN Se3/0:1:23 Q931: Applying typeplan for sw-type 0x2 is 0x2 0x1, Calling num 5024101498
*Sep 4 17:57:59.005: ISDN Se3/0:1:23 Q931: Applying typeplan for sw-type 0x2 is 0x2 0x1, Called num
*Sep 4 17:57:59.005: ISDN Se3/0:1:23 Q931: TX -> SETUP pd = 8 callref = 0x008E
Bearer Capability i = 0x8090A2
Standard = CCITT
Transfer Capability = Speech
Transfer Mode = Circuit
Transfer Rate = 64 kbit/s
Channel ID i = 0xE9868398
Exclusive, Interface 6, Channel 24
Calling Party Number i = 0x2180, '5024101498'
Plan:ISDN, Type:National
Called Party Number i = 0xA1
Plan:ISDN, Type:National
*Sep 4 17:57:59.133: ISDN Se3/0:1:23 Q931: RX <- RELEASE_COMP pd = 8 callref = 0x808E
Cause i = 0x819C - Invalid number format (incomplete number)
*Sep 4 17:57:59.133: ISDN Se3/0:1:23 **ERROR**: call_cleared: VOICE ERROR: NULL VDEV Common(0xFC): bchan -1, call id 0x8016
*Sep 4 17:57:59.141: //-1/BC10816380D4/RXRULE/regxrule_stack_pop_RegXruleNumInfo: stack=0x6871D9EC; count=2
VoiceEncapPeer150
peer type = voice, system default peer = FALSE, information type = voice,
description = `',
tag = 150, destination-pattern = `011.T',
voice reg type = 0, corresponding tag = 0,
allow watch = FALSE
answer-address = `', preference=0,
CLID Restriction = None
CLID Network Number = `'
CLID Second Number sent
CLID Override RDNIS = disabled,
source carrier-id = `', target carrier-id = `',
source trunk-group-label = `', target trunk-group-label = `',
numbering Type = `unknown'
group = 150, Admin state is up, Operation state is up,
Outbound state is up,
incoming called-number = `', connections/maximum = 0/unlimited,
DTMF Relay = disabled,
URI classes:
Destination =
huntstop = disabled,
in bound application associated: 'DEFAULT'
out bound application associated: ''
dnis-map =
permission :both
incoming COR list:maximum capability
outgoing COR list:minimum requirement
Translation profile (Incoming):Calling_Party_Num
Translation profile (Outgoing):outgoing_international
incoming call blocking:
translation-profile = `'
disconnect-cause = `no-service'
advertise 0x40 capacity_update_timer 25 addrFamily 4 oldAddrFamily 4
type = pots, prefix = `',
forward-digits 0
session-target = `', voice-port = `3/0:1:D',
direct-inward-dial = enabled,
digit_strip = enabled,
register E.164 number with H323 GK and/or SIP Registrar = TRUE
fax rate = system, payload size = 20 bytes
supported-language = ''
preemption level = `routine'
bandwidth:
maximum = 64 KBits/sec, minimum = 64 KBits/sec
voice class called-number:
inbound = `', outbound = `'
dial tone generation after remote onhook = enabled
Time elapsed since last clearing of voice call statistics never
Connect Time = 0, Charged Units = 0,
Successful Calls = 0, Failed Calls = 15, Incomplete Calls = 0
Accepted Calls = 0, Refused Calls = 0,
Last Disconnect Cause is "1C ",
Last Disconnect Text is "invalid number (28)",
Last Setup Time = 50369257.
Last Disconnect Time = 0.
T1 3/0:1 is up.
Applique type is Channelized T1
No alarms detected.
alarm-trigger is not set
Soaking time: 3, Clearance time: 10
AIS State:Clear LOS State:Clear LOF State:Clear
Version info of slot 3: HW: 1536, PLD Rev: 6
Framer Version: 0x58
Manufacture Cookie Info:
EEPROM Type 0x0001, EEPROM Version 0x04, Board ID 0x01,
Board Hardware Version 6.0, Item Number 73-4089-07,
Board Revision A0, Serial Number JAE08512FBJ,
PLD/ISP Version 48.53, Manufacture Date 13-Dec-2004. -
Bursting control :DocumentProcessor does not use translation while bursting
Hi
We are trying to use the bursting feature in BI Publisher using the DocumentProcessor class/APIs.
The java code is :
import oracle.apps.xdo.batch.DocumentProcessor;
public class BurstingTest
public BurstingTest()
try {
DocumentProcessor dp = new DocumentProcessor ("bursting_cntl.xml", "test.xml","temp");
dp.process();
catch (Exception e) {
System.out.println(e);
public static void main(String[] args)
BurstingTest burst1 = new BurstingTest();
The bursting control file is :
<xapi:requestset xmlns:xapi="http://xmlns.oracle.com/oxp/xapi" type="bursting">
<xapi:request select="/XXG_ACCOUNTING_CNDN_REPORT/G_Cust">
<xapi:delivery>
<xapi:filesystem id="file1" output="C:\Projects\XDO\RTF_TO_PDF\output\${cust_name}.pdf"/>
</xapi:delivery>
<xapi:document output-type="pdf" delivery="file1">
<xapi:template type="rtf" locale="fr-FR" location="C:\Projects\XDO\RTF_TO_PDF\test.rtf"
translation="C:\Projects\XDO\RTF_TO_PDF\test_fr_FR.xlf" >
</xapi:template>
</xapi:document>
</xapi:request>
</xapi:requestset>
The XLF file has the necessary translations. Source en-US and target fr-FR.
However, I see that the translations are NOT being picked by the DocumentProcessor. The bursting does happen successfully, however I don't see the translations in the PDF.*
Am I missing something here? Probably some flag that I need to set or something of the kind?
A section of the XLF file is as shown below :
<?xml version = '1.0' encoding = 'utf-8'?>
<xliff version="1.0">
<file source-language="en-US" target-language="fr-FR" datatype="XDO" original="orphan.xlf" product-version="orphan.xlf" product-name="">
<header>
<prop-group name="ora_reconstruction">
<prop prop-type="extractorVersion">5.6.3_120.1</prop>
</prop-group>
</header>
<body>
<trans-unit id="5dacac6a" maxbytes="4000" maxwidth="56" size-unit="char" translate="yes">
<source>Please confirm the above information.</source>
<target>Merci pour confirmer l'information mentionee</target>
<note>Text located: body</note>
</trans-unit>
<trans-unit id="366403c2" maxbytes="4000" maxwidth="23" size-unit="char" translate="yes">
<source>Dear [&0],</source>
<target>Cher [&0],</target>
<note>Text located: body</note>
</trans-unit>
<trans-unit id="ce145901" maxbytes="4000" maxwidth="23" size-unit="char" translate="yes">
<source>Invoice Date</source>
<target>Date de la facture</target>
<note>Text located: body/table/table header</note>
</trans-unit>
Request you to revert as soon as you could.
Thanks and Regs
Krish
Edited by: user11131627 on Nov 8, 2009 10:16 PMIke
Yes, I believe the translation element is defined.
Referred to this post about that :
http://blogs.oracle.com/BIDeveloper/2009/06/bursting_translation.html
Also, we did try using the translation element thru' Apps and submitted as a standard concurrent program.
The translation fie was used correctly.
My question is :
How do I force the usage thru' my custom Java program and in which I use DocumentProcessor? -
Dunning letter script form translation
Hi!
I am translating dunning script form to chinese language(ZH), original script form is in Enlgish language.
I have selected langage ZH key in the header data of form, but while creating the form in chinese langauge system is giving following error:
Form *ZSOLLECITON01_* language EN should not be translated to ZH
Message no. TD114
The same form name is available in EN language.
I am using transaction code SE71 where I am inserting above form name and langauge key ZH and try to create form?
Can any one explain me how to create above form in ZH language?
regs,
RameshHi,
Please copy that from.
Goto SE71
Give ur form name and required language click on change
and click ok
It opens the form
In menu options form--->copyfrom
Give your form name and original language
Save and Activate.
It resolves ur problem.
Regards,
Venkat -
Currency Translation on Key Date for AR Aging
Need your valuable advice!
I have created an AR Aging query including both Open and Cleared Items based on 0FIAR_C03_Q0005 standard query. However the requirement is to do currency translation to Group Currency (USD) on Key Date. This Key date is defaulted to today but the user can change this to go back in time and pull all the ARs as of that back dated key date.
I was planning to create a currency translation type on M rate based on the Key Date Variable in RSCUR. However I am confused on which variable to base this currency translation. I have several key date variables in my query such as 0P_KEYD2 (based on Posting Date), 0P_KEYDT (based on Net Due Date) and 0P_KEYD3 (based on Clearing Date).
Which Key Date Variable should I use in 'Time Reference from Variable' field in RSCUR? Would it be one of the 3 mentioned above or something else and why?
Appreciate your valuable advice.
Thanks,
AlHi,
Yes I do want to use the Key date from the variable screen and I am using the standard 0FIAR_C03_Q005 with slight modification including currency translation.
As I mentioned in my original post I have several key date variables in this query such as 0P_KEYD2 (based on Posting Date), 0P_KEYDT (based on Net Due Date) and 0P_KEYD3 (based on Clearing Date). My question is which one should I use if I want to base it on the specific key date variable from the variable screen? I need the specific Key Date variable technical name.
Thanks,
Al -
XML Publisher report - Number translation in Italian
While i am Doing an XMl publisher report in english and Italian Languages i am facing an issue with the Dot translation.
For eg: 4.5 is translated to 4,5 in Italian.This creates a problem for me when i am doing summary on this column.So how should i handle in case italian.better to ask this question in the BI (XML) Publisher Forum: BI Publisher
-
Hi All,
I am getting the following error while running a report in Answers tool.
State: HY000. Code: 10058. [NQODBC] [SQL_STATE: HY000] [nQSError: 10058] A general error has occurred. [nQSError: 46115] No Unicode translation is available for some of the input characters for MultiByteWideChar(). (HY000)
I am seeing this error on my local windows desktop. The database is oracle 10g.
The error is not very consistent. Sometime it works and then it fails because of the above error. Not sure what is causing it.
thx,
Bejoy
Edited by: bejoy.nair on Sep 1, 2009 9:00 AMI am also receiving the same error, but from within Answers. It occurs occasionally, depending on what fields I select. I am trying to narrow it down to a field and field type. I am using OBIEE 10.1.3.4.0 and Oracle 11g.
Any help would be appreciated.
Thanks,
Anne -
Media Encoder CC 2014.0.1 error on install: I can't unpack the downloaded files (translation).
I have troubles with the latest update of Media Encoder CC (2014). I get an error which says: I can't unpack the downloaded files (translated from Dutch). Please try again. I try again, but it don't help. I have a MacPro early 2008 with Mavericks.
=======================================
Moderator moved thread from Premiere Pro forum to AME, and trimmed the title.Looks like one component in Media Encoder is either missing or corrupted somehow.
Could you uninstall Adobe Media Encoder CC 2014 and please make sure all files are deleted after uninstall? Then, please try re-installing it. -
Sapscript translated in non-english language - Garbled output as Email
Hi Experts,
I've translated a SAPscript to Chinese and Thai language.
As per my requirement, the output can either be printed, emailed or faxed.
I'm using the standard include RVADOPFO for Open form.
For the english version, I'm able to recieve the properly formatted e-mail output.
However in case of thai and chinese, the Thai and Chinese characters do not appear. Most of them are substituted with blank spaces and some are substituted with boxes and unknown characters. However, the numbers and english characters appear.
Please help in getting the correct output.
Thanks!
Nitya.Hi,
SAP 141343. PDF Conversion: Latin-2.
SAP 141901. Customer-specific fonts for PDF conversion.
SAP 163266. PDF conversion: character set for softfonts.
SAP 171698. SAPconnect: Formats, conversion, device type.
SAP 317851. Creating PDF format via spooler in 4.6C/4.6B/4.5B.
SAP 322998. PDF conversion: Cyrillic support.
SAP 323736. Restrictions with "PDF print" through spooler.
SAP 398357. PDF converter: Width of letters is incorrect.
SAP 414325. SAPconnect: Conversion of ALI to PDF.
SAP 504952. Composite note spool and print.
Find these notes, there You'll find some answers.
Regards,
Nisrin.
Maybe you are looking for
-
Mail stuck "cannot send using server"....
but the real issue is that the list of addressees is so long that I cannot see the buttons at the bottom, so I cannot click them to dismiss the error and try something else. Only way out of Mail is to force quit (menus are unresponsive) and if I rela
-
This usually wouldn't pose to be a problem, but I am a college freshman and I just redeemed my $100 giftcard to the app store. I am beyond frustrated and don't know what to do. It is my first time making a purchase off of this Mac with this account,
-
Primary Key rule Violation error while Insert Record in Compact DB
Hi All, I have One Table in Server Name "Student" when i Synchronize this with the help of Microsoft Synchronization Framework same Table schema with Data has been create in CompactDataBase. When i insert data in CompactDataDase it give me Primary K
-
Hello friends, Can anyone out there tell me or point me to information on how to set up the ASE_ENCRYPTION option for version 15.7? I have an existing ASE installation for testing purposes. I want to install the encryption option there but I cannot l
-
This started after i down loaded new firefox.last week.I didn't have any problem before that.It won't bring it up period.It just says your browser not supported by web Dynpro.