Regard an error "Storage type & notsuitable as interface (SU mgmt is active

Hi All,
I am trying to do the inventory clearing in both warehouse and Inventory management using the transactions LI20 and LI21 after counting the inventory. But whenever I am trying to do the writeoff's I am facing with an error "Storage type & not suitable as an interface (SU management is active)"
I couldnt able to figure out the main cause for this error. Your valuable suggestions would be highly appreciated.
Regards,
Shane

Hi Jürgen L,
My objective is to do physical inventory and of ther are any differences then write them........in this sytem Both Grants and fund management is involved?
I am getting this message while I am doing LI21. And you have suggested that, the difference storage type SU managed. which is a 999 storage type. and this is not SU managed.
I would also like to ask regarding the clearing of differences in warehouse and Inventory mangement. I am using the mvmt types 711 and 712, But what account documents will get generated. I am thinking there will be no account documents that will get generated. Adding to this I am getting "Account 6701 requires an assignment to a CO object with Message no. KI235". If we do this assignment to this CO object......... doesnt the transaction go and hit the balance sheet account.
I am lil baffled with this whole process. If you could give me your valuable information, that will help me a lot.
Shane.

Similar Messages

Error mesage related to storage type

Hi
Iam PP guy and getting following message while making container full in Kanban board PK13n
Storage type xxx not suitable as an interface (SU management is active)

I think you are using storage unit active storage type for this interface.Please use non storage unit active storage type.You can check storage types in define storage types which one is non storage unit active one.

WM - Storage type 001 is not suitable as an interim storage area -

Hi,
When i'm doing Migo, the blw error has came, pls advise , how solve it..
seems, some where i made wrong config.. These process i was trying in our ides server..
Storage type 001 is not suitable as an interim storage area
Message no. L9022
Diagnosis
You have attempted to execute a posting to a dynamic coordinate in a storage type for which a putaway strategy is defined. Dynamic coordinates, however, are provided only for storage types without a putaway strategy.

thanks Raman
pls tell me now , where i have to check the config.. and where i may did the mistake.
for ur info, ref to sdn A08- conf guide as per blw , i made the conf..
3.1 Full WM Basic Settings
3.1.1 Defining Control Parameters for Warehouse Number
3.1.2 MM-IM Storage Location <-> Warehouse Number     J01
3.1.3 Defining Storage Type                                              001- high rack system
3.1.4 Defining Storage Section                                            001- Fastmoving
3.1.5 Defining Storage Bin Types                                   P1-BIN HEGIHT 1 MTR
3.1.6 Defining Blocking Reasons                                           1
3.1.7 Defining Storage Bin Structures
3.1.8 Defining Storage Type Indicators                                1
3.1.9 Defining Storage Unit Types                                    E1
3.1.10 Defining Storage Section Indicator                        001- Fastmoving
3.1.11 Defining Bulk Storage Indicator                                      B1
3.2 Strategies
3.2.1 Activating Storage Type Search
3.2.2 Activating Storage Section Search
3.2.3 Activating Storage Bin Type Search
3.2.4 Defining Sort Sequence for Putaways (Cross-line Stock Putaway) Definition of Sort Field in Storage Bin
3.2.5 Defining Strategy for Pallets
3.2.6 Defining Putaway Strategy for Bulk Storage
3.2.7 Defining Strategy for Stringent FIFO
3.2.8 Defining Strategy for Large/Small Quantities Determining Search Sequence
3.3 Activities
3.3.1 Defining Requirement Categories
3.3.2 Defining Shipment Types
3.3.3 Defining Movement Types
3.3.4 Defining Stock Transfer and Replenishment Control Defining Replenishment Control for Storage Type
3.3.5 Setting up 2-Step Picking
3.3.6 Defining Confirmation
3.3.7 Print Control
3.3.8 Defining Default Values
3.3.9 Defining Types for Storage Type
3.3.10 Defining Difference and Document Limit
3.3.11 Clearing Difference (Interface with IM) MM-IM Movement Types for Clearing Inventory
3.3.12 Clearing Difference (Interface with IM)  Do Not Allow Clearing in Storage Types
3.4 Interfaces
3.4.1 Allowed Negative Stocks in Interim Storage Types Allowing Negative Stock for Each Storage Type
3.4.2 Shipping Shipping Control per Warehouse Number
3.4.3 Shipping  Requirement Types of Delivery Documents
3.4.4 2-Step Picking
3.4.5 Creating Automatic Transfer Order
3.5 Manual Activities
3.5.1 Maintaining Number Range and Assignment
3.5.2 Maintaining Number Range for Physical Inventory
3.5.3 Creating Storage Bins
3.5.4 Generating Interim Storage Bin
Edited by: UJ on Mar 4, 2009 7:16 AM

Automated storage type and bin

hi
thanks for givining reply
i extened the mmo1 and while doing the lt06 this storage type is coming in the destination place but the bin not coming error is coming there is no bins in the storage type
can u tell me is there any setting required in storage type .
fixed bin means which u mentiones in wm2 view i had given only some bin which created in the storage type .is it correct.i will not activated the storage section check in storage type .
can u tell me step by step .

Hi,
Here you can find the prerquisits of fixbed bin putaway strategy:
http://help.sap.com/erp2005_ehp_03/helpdata/EN/c6/f844834afa11d182b90000e829fbfe/frameset.htm
When you get the error message, please goto menu > Enironment > Stor. Bin Search Log - here you can see what is the problem.
In LX03 you can list the existing storage bins in your stoarge type - make sure you really have the bin.
Regards,
Csaba

Create T.O using outbound delivery. Need to update the storage type.

Hi All,
I am using L_TO_CREATE_DN to create a T.O using an outbound delivery. It creates the T.O. But I need to decide at the time of creating the T.O the storage type to be used.
I tried using the F.M L_TO_CREATE_MULTIPLE but that does not update the Delivery flow.
I have already gone over the discussions on forums for L_TO_CREATE_DN but none seem to answer the question of updating the line items of the transfer order yet.
I was hoping someone could help me out with this.
Thanks,
Arup

Hey,
Well I do not need to be worried about the storage bins as that is a selection based on a FIFO strategy. It is returned by the system.
I need to worry about the storage type.
So here is the complete requirement.
I have to create TO's for LM05 and LM45. The LM45 To's have to be associate with storage units and this association occurs only if I choose VWT as the storage type..
When I choose VWO as the storage type then the items are not associated with a Source Storage Unit. This is because the storage type VWO does not have SU management active whereas VWT has SU management active.
So, what I am primarily concerned about is the way I could enter the storage type information dynamically.
Arup

Error Addition to stock of material A in storage type 002 is not allowed

Dear all,
I am doing GR for PO in WM. During TO creation I am getting this error Addition to stock of material A in storage type 002 is not allowed. Hence no storage bins can be entered. May I know under what scenarios this type error props up?
Thanks in advance,
Prashanth

Please find the explanation in SAP online help:
http://help.sap.com/erp2005_ehp_04/helpdata/EN/c6/f8449d4afa11d182b90000e829fbfe/frameset.htm
SPRO > LE > WM > Master Data > Define Storage Type
Check
- putaway strategy --> V_T3010-STEIN
- addition to existing stock indicastor ---> V_T3010-ZULAG
As you can read in the help, other factoers such as capacity may influence this.
Regards,
Csaba
Edited by: Csaba Szommer on Feb 19, 2010 7:55 AM

Error during Stock movement between two storage type

Dear Friends
How do i move the stock from one storage type to other storage type within a warehouse?
In the material master i have maintained a storage type indicator for automatic storage type determination.
now when i create a TO for moving the stock from the orginal loaction to other location (NOT INTERIM) i am getting an error
Error occurred during storage section search (1740 003)
Message no. L3041
Diagnosis
No storage area search has been defined for this material and this storage type.
Please assist
Thanks

Dear,
Kindly specify the storage section indicator in Material Master - WM view.
Regards,
Sandip

Error - No destination storage bin to be found in storage type

Hi all,
this is my flow -
Create STO PO - ME21n
create deliveries via - BAPI_OUTB_DELIVERY_CREATE_STO
create Transfer order(TO) - L_TO_CREATE_DN - for o/b delivery
confirm TO- L_TO_CONFIRM
Using BDC i am doing PGI for VL02n
create Transfer order(TO) - L_TO_CREATE_DN - for i/b delivery
confirm TO- L_TO_CONFIRM
Create GR - 'BAPI_GOODSMVT_CREATE'
Here till PGI my report pgm is working fine. and when cominf to TO create based on i/b delivery i am getting error -
No destination storage bin to be found in storage type 104
I have added 2 lines in the FM at exception part -
error_message = 16
OTHERS = 32.
So my return code for the FM - L_TO_CREATE_DN (_FOR i/b delivery)_is 16
message class : L3
message number : 009
message type : E
No destination storage bin to be found in storage type 104
Can any one tell me how can be this rectified - Is this a config related issue or data problem ?
Pls help me.
Sen

Hi all,
Thanks for your replies.
Manish: Where do I see that the storage bin is created with respect to storage type? I was checking LS03N where I can see that the storage bin is created for storage section and storage bin type. Configuraiton is like below:
Storage Bin search Strategy:
(1) By storage section: Not active
(2) By Stotage Bin type - Active and the storage bin type is assigned to a storage type.
I have one storage bin available (Bulk Storage) for the selected storage Bin type BUT it is not automatically searched by the process. Material master has WM view1 with storage type indicator and there is a config for storage type search which is working good. The only issue is searching storage bin while creating TO during Goods movement, in particular Put away. Also please note that the storage bin is not hardcodes in material master).
This error happens for all the scenarios (unrestricted, blokced or when WM stock is initial or when the materrial is created first time and subject the WM movements).
When I first started this question I thought that the error happens only for Blocked status. Actually it is happening for all the scenatios when the WM stock in initial.
Hope my scenarios are clear. Thanks in advance for your help again.
Best regards
Nagarajan

In mb1b when am doin 311 am getting storage type error

Hi friends,
Storage type 005 is not suitable for an interim storage area, this error am getting when i do 311 in mb1b
thanks and regards,
bala r.v

Check your config for storage type 005. Make sure you do not have the storage type repeated in the Origin and Destination storage types. You should have the "Dynamic" box checked next to the storage type and not populated with storage type 005
IMG path below recalled from memory, so it may not be exact)
IMG: Logistics Execution > Warehouse Management > Master Data > Maintain Storage Type. Check storage type 005 for your warehouse

SUT Error at TO Creation from Non-SU to SU managed Storage type

Hi
I am creating TO to move quants from Non-SU Manged Storage type to SU managed Storage type, but at first its giving error saying Enter SUT for storage type. These Non-SU managed Storage types are not having SUT Check but SU Managed storage type is having SUT Check.
I tried to update WM view-2 with SUT and palletization but still issue exists.
I am having batch job for RLAUTA10 where TR is converted to TO but due to above issue , this batch job is getting failed.
I am deseperately trying to find the root cause and fix this asap. Let me know how this issue can be resolved??
Thanks

Like I mentioned earlier in my posts, SU's are typically not managed in interim storage types. Apparently, in this case, the PSA is an SU managed location and you are trying to move inventory from a non-SU ST to SU PSA ST. The isse that you are encountering is due to the reason that the palletization data maintained in the material master is defaulted during receipts rather than staging therefore, the SUT field in the TR remains blank. But, due to business reasons you are using SU's in PSA's then you'd have to venture into development options to include SU types during automatic converion of staging TRs into TOs.

Query regarding Storage type

Hi,
Can we have change existing storage type (like geo-redundant to locally-redundant storage)?
If yes then kindly help me to describe.
Regards,
Arvind

Hi,
In addition to "Azure-Amjad" reply,
If you trying to change the replication type from "GeoRedundant" to "Locally Redundant" through Powershell, then you may try below command:
Set-AzureStorageAccount -StorageAccountName <storageaccountname> -GeoReplicationEnabled $false -Label “disabled geo replication”
Before, you execute the above command, check if the GeoRedundant is enabled or disable by following command:
Get-AzureStorageAccount -StorageAccountName <storageaccountname>
Regards,
Manu Rekhar

Storage type to be assigned to particular storage location

Hi,
As per clients new business requirement, 2 storage locations of a plant are assigned to same warehouse.
But as the storage types comes under warehouse they come under both the storage locations. Is there any configuration to assign specific storage types to a particular storage location.
I tried in SPRO under interfaces>IM>Storage location control but it does not allow.
Please advice.
Regards,
Pratap

Hi,
I feel the solution given by E060123 in his first reply should work well.
Did you first define the storage location refernce and then in the same config node under "Control of Assignment "Plant / Stor.Loc. - Whse Number" assigned the sloc reference to the respective storage location
And then assigned the reference to the search table as mentioned previously.

Regarding smartforms error

hi experts,
i have developed a driver program for the smartforms ,in the driver program i am displaying with the help of final internal table and with the help of structure i m declaring an internal table in the smartforms,the structure is containg the fields which i used in the driver program for output but when i execute this its giving error...plz helpme to short out this problem what are the points i must consider while declaring structure ....
the error:::
ShrtText
Type conflict when calling a function module (field length).
What happened?
Error in ABAP application program.
The current ABAP program "ZRAW_PRODUCTION_REPORT_SFM" had to be terminated
because one of the
statements could not be executed.
This is probably due to an error in the ABAP program.
A function module was called incorrectly.
Error analysis
An exception occurred. This exception is dealt with in more detail below
. The exception, which is assigned to the class 'CX_SY_DYN_CALL_ILLEGAL_TYPE',
was neither
caught nor passed along using a RAISING clause, in the procedure "FORM_DISP"
"(FORM)"
Since the caller of the procedure could not have expected this exception
to occur, the running program was terminated.
The reason for the exception is:
The call to the function module "/1BCDWB/SF00000211" is incorrect:
In the function module interface, you can specify only
fields of a specific type and length under "ITAB_FINAL_SFM".
Although the currently specified field
"ITAB_FINAL" is the correct type, its length is incorrect.
the final table in the driver program is given below::
,from this table i m showing output.......
TYPES:BEGIN OF S_FINAL ,
MATNR TYPE MARD-MATNR, "for material number
WERKS TYPE MARD-WERKS, "for plant id
LGORT TYPE MARD-LGORT, "Storage location
LABST TYPE MARD-LABST, "opening stock
INSME TYPE MARD-INSME, "Stock in quality inspection
SPEME TYPE MARD-SPEME, "Blocked stock
EINME TYPE MARD-EINME, "Totl Stck of All Restricted Batches
RETME TYPE MARD-RETME, "Blocked Stock Returns
LIFNR TYPE MSEG-LIFNR, "vendors number
MAKTX TYPE MAKT-MAKTX, "for material description
NAME1 TYPE T001W-NAME1, "plant name
NAME2 TYPE LFA1-NAME1, "vendors name
LABST_TM TYPE MARD-LABST, "target monthly
LABST_CL TYPE MARD-LABST, "closing stock
LABST_RT TYPE MARD-LABST, "receive today
LABST_RTLD TYPE MARD-LABST, "receive till date
LABST_RTY TYPE MARD-LABST , "receive till year
LABST_IT TYPE MARD-LABST, "issued today
LABST_ITLD TYPE MARD-LABST, "issued till date
LABST_ITY TYPE MARD-LABST, "issued till year
BWART TYPE MSEG-BWART, "movement type
MBLNR TYPE MSEG-MBLNR, "material doc number
EISBE_CL TYPE MARC-EISBE , "closing balance
EISBE TYPE MARC-EISBE, "safety stock
LGOBE TYPE T001L-LGOBE, "Description of storage location
P_DATE TYPE SY-DATUM, "for previous date
GPTXT TYPE T750E-GPTXT, "for remarks
END OF S_FINAL.
DATA:ITAB_FINAL TYPE STANDARD TABLE OF S_FINAL WITH HEADER LINE.
the fields which are bolds i m not showing in the output using for some calculation thatsit.
with the refrence of this final table how will i declare my structure so that it wont give the above error if possible kindly send me the syntax of declaring structure along with my fields....

hi
its better dat u create a structure in abap dictionary in se11...den declare ur internal table of dat type in program and declare ur structure and internal table in smartform of dat type (dictionary structure).im sure dis problem wont arise...
plz reward points if it helps

HU without inventory management and message L3778 in storage type 999

Hi experts,
Need suggestion on the process to add inventory of an HU with status 'HU without inventory Management'. This issue has occurred out of the below scenario:
1. our warehouse is HU & WM managed.
2. We have a transfer order for a delivery document requesting to pick up 100 cases of MAT1 which is assigned to HU1.
3. While confirming the transfer order user has confirmed difference for the full quantity of 100 because the SU/HU was not found in the bin.
4. The system has set the status of HU as 'HU without inventory Management'. The HU is empty.
5. system has moved the stock from the bin to difference storage type 999.
Now user has found the stock for this HU and he wants to post the stock back into the bin. system does not allow to move the stock back to bin using LT01 as we get error message 'L3 778'.
What will be the best practice to get the stock back into the bin and post the stock into the same old HU.
Is there a process wherein we can post this stock to another bin and repack into the old HU?
Thanks,
Harish

Thanks Manish on the hint. I was able to transfer stock to partner location and then bring back to original Storage type/Bin. Below steps was used to fixed the issue:
1. Initiate a transfer of stock from WM/HU Sloc where the IM stock resides into Sloc 9099. An outbound delivery is created during this process.
2. Create a transfer order with reference to delivery and pick the stock from 999 storage type.
3. Create a Pick HU using LH01 and assign the HU on the pallet to the transfer order.
4. Confirm the transfer order using LT12.
5. Perform PGI for the delivery.
6. Use HUMO to display the HU and then you can transfer the stock back to WM/HU location using the storage location transfer option available on the HUMO screen(EDIT à change HU posting à Storage location)
7. Perform Bin to bin transfer to move the SU from 921 storage type to putaway the HU/SU back to the destined Storage type/Bin.
Best Regards,
Harish

Control data for storage type is missing Message no. L3006

Dear Mates
i am trying to create a transfer order from delivery. the moment i click on save in LT03 its giving me the error message as
Control data for storage type is missing
Message no. L3006
i have explored every thread regarding the same issue and also implemented some measures like
-> extending the material to particular warehouse and maintaining stock removal and stock placement strategies in it(i created new one from MM01 itself)
-> going to spro path SPRO->Logistics Execution->shipping->picking->Lean WM->Define storage type. and assigned storage type.
but still i am getting the same message in LT03
can you please help me out on this.

Please take a look at the following links and see if they will help at all.
Error on creating a TO - Control data for storage type is missing
"control data for storage type is missing"
Kind Regards,
Jason

Regard an error "Storage type & notsuitable as interface (SU mgmt is active

Similar Messages

Maybe you are looking for