Regarding data storage

Dear all,
I am doing cost element planning monthly for a cost center through Tcode-KP06.
Can anybody know in which table this data will store. Pls let me know the table..
Thanks in Advace..
Regds,
Janardhan.

hi if u want to show the table for kp06
open kp06 and goto system menu->services->view maiantenance  here u find out the table.
or other wise go to sm30 and search it .

Similar Messages

  • Windows 7 64bit Raid 1 Data Storage setup with UEFI and 6TB drives

    i just bought a GigaByte MB with UEFI bios, 1 SSD 128GB drive for the OS (boot up), and 2 6TB drives for use in a raid 1 setup for the data storage.
    I have been able to install win 7 64bit using the UEFI dvd drive.  I have been able to define the 6TB mirror via the bios (under the Intel Rapid Storage Technology option) .  But when ever i go into windows, and check under Disk Management, i don't
    see the raid 1, i see two drives listed for the data, each at 1492 GB.   I should be seeing 1 drive at 5.4TB.  
    note: I have tried re-installing win7 64bit many times to see if i have missed something.   When i run setup off uefi dvd drive, i see that drive 1 (of what should be part of the mirror) and drive 2 are listed there at the reported 1492 GB size each.
    So it seems that win7 doesn't see that mirror that i created via the bios. So is this a bios setting problem somewhere?   i presume on this screen i should see the correct mirror size already.
    Also, do i need to install win7 via the uefi dvd if  i don't want to boot off those large drives (i just want to boot off the ssd. But when i did try that using a legacy mode, i couldn't later try to create a single large drive for the mirror using
    GPT formatting.  it just wasn't an option.  although the mirror was recognized as 1 drive, but broken into 2TB and 3TB.)
    what could i possibly be doing wrong??  
    Thanks for any help

    Thank You Roger.   I did call Gigabyte.   This is how i solved it with the gigabyte support team. 
    1.   Don't try installing Win7 64bit sp1 and setup RAID at the same time.  (even go ahead and unplug those raid drives if you have it plugged in).   The OS should be installed first on the boot drive, but make sure the BIOS is already set
    to RAID (not AHCI.  If you already installed OS under AHCI, you need to reinstall OS.  i find this crazy because what if you decide to install raid down the road.. to an existing machine.. you can't do that because of this).     Make sure
    to install OS with the UEFI dvd drive option (i had done this).
    2. Once the OS is installed, install all drivers that come for the Motherboard... That should include intel Raid drivers. (note gigabyte support didn't tell me to do this, but i didn't want to take a chance to have to reinstall OS again or have more problems,
    but it makes sense.)
    3. Now i have the GA-H97-Gaming 3 mother board, it had Bios F3.  I upgraded it to F5 as per support tech.
    4. turn off machine, and replug in the two 6TB drives.
    5. after reboot, i find out that i no longer see Intel RAPID Storage Technology. (this should have displayed when i set the SATA Mode Selection to RAID before i started all this business... it did under bios F3, but not under F5.. bug??  i think so,
    so i plan on letting gigabyte know about this).  This is a problem.  In Intel RAPID Storage Technology is where you define the RAID in the first place.    OK, well after several reboots.. i tried to use CTRL-I to get to intel's interface
    rather than that of the gigabyte bios.   Voila... i define the Mirror... 
    6. I am able to boot into OS.   I got to Drive Management.  I now see 1 6TB drive.  I initialize it of course using GPT.  Format it.  All all looks good now.   
    Hope this helps someone.. took me enough tries to get it right.   I really am bothered about requiring the OS installed in the correct SATA mode just to get RAID working.  As i mentioned, you can't change your mind afterwards without reinstalling
    OS.   Also i couldn't even get the OS setup to start when i had those raid drives plugged in.. so make sure to unplug them.
    Best Regards.

  • Data storage format by berkeley DB

    Hi,
    I have a few questions regarding how data storage is achieved by Berkeley db.
    I created a Berkeley DB database called 'BDB' by inserting 1million <key,value> pairs. The environment name was set to 'BENV'; that means, I had to create a directory named 'BENV' in the current working directory before executing the program.
    After invoking the program and completing the insertions, I saw a file 'BDB' in the 'BENV' directory. The size of 'BDB' is 56Mb. Further, there are 4 more files: __db.001 ... __db.004. Sizes of these files are 4Kb, 320Kb, 1.9Mb and 608Kb.
    I should mention that I didn't enable logging when I created the database and environment.
    My question is: why are there so many files and what are their purpose? I have a feeling that the files '__db.00x' (where x=1 to 4) also store data. Coz, I created two more databases with 10million and 200million records.. and they have these files too, just that their sizes have increased quite a bit.
    I am trying to understand more details about the data storage layout of Berkeley DB and I would appreciate any help regarding this.
    Thanks.
    Andor

    Are you using the STL interface? We have code that uses the raw C++ interface and this does not create those files starting with '__'. Whereas the code that uses STL interface creates such files. I have not bothered much now as I need those files during the process lifecycle. My use of Berkeley DB here is more like a disk backed set rather than a true persistent database.
    I would try running a checkpoint() to see if they get into a single file before closing the DBEnv. Let me try as I have a sample code using DB STL interface.

  • ADI0052E: TSM API Error: ANS1311E (RC11)   Server out of data storage space

    Hello guys,
    I have a problem with the backup on MaxDB. It always fails with the following error message
    ADI0052E: TSM API Error: ANS1311E (RC11)   Server out of data storage space
    Has anyone faced this problem before? Any solution how could this be solved?
    Thanks for your help.
    Regards,
    Dan

    Hi Dan,
    Check the TSM server and make sure the primary storage pool that is defined
    as your copy destination for the management class you are using is not full
    and or you have not run out of scratch tapes. In either case a storage pool
    has filled up and cannot migrate data causing the RC11. This is usually what
    an RC11 Server out of data storage space means.
    I am sharing configuration for Oracle database. You can check similar configuration for MaxDB database.
    when i defined the node in my tsm server :
    REG NODE hostname_oracle password maxnummp=2, it was defined in standard storage pool, i moved it in other storage.
    Hope this is useful.
    Regards,
    Deepak Kori

  • WAAS Apliance usable storage -vs- maximum data storage

    We are looking into deploying the new Wave 594 and have a question about the drive space. The unit comes with a 500G drive and a second optional 500G drive. In one place on the specs they say optional second hard disk drive for RAID 1 redundancy but under the hardware specs they list maximum data storage as 2 x 500G HDD. Do I have the potential for a total of 1T of space or just 500G Raid1? Also is the space divided up dynamically or are there hard limits? I figure some of this space needs to be allocated to the DRE cache and the rest for other data storage such as prepositioning. I am trying to find out what my maximums would be.
    Brent                   

    Hi Brent,
    Don't bother.
    You cannot change the allocations between the different allocations.
    WAAS installation (WAAS rescue disk or preinstalled) will determine the allocation based on :
    The device model
    The amount of RAM installed (within the supported specs)
    The reason for putting in an additional disk, in a 594, is solely for RAID-1 purposes, you will always end of with 500GB disk space.
    You have to ask your Cisco accoung manager for the precise sizing guides, but for a :
    594 w/8GB RAM (default) - you'll end up with 80GB of DRE disk cache and 100GB for the CIFS object cache
    594 w/12GB RAM - you'll end up with 120GB of DRE disk cache and 100GB for the CIFS object cache
    and these cannot be modied.
    Best regards
    Finn

  • Error data Storage

    what is error data storage at XI? Also provide me the details  along with screeshot.

    Hi Shweta,
                  All error log's stored at following location.
                 i,e /usr/sap/X01(system id)/DVBMGS000/j2ee/cluster/dispatcher/log.
    wher u can find system and default trace.
    u can saw all error log's at that location.
    warm regards
    mahesh.

  • V4.2 error: Short term data storage is full

    Hope someone here can help.  We are still using 4.2 for now.
    Upon logging into Admin, we are receiving an error stating "PLANNING short term data storage is full, do you want to optimize the application?".  When checking the appset status the application only has about 400 records in short term storage.  We have tried saving the application immediately followed by optimization, yet this error continues.
    Any thoughts on how to rectify this?
    Thank you.

    So you have scheduled a lite optimize or full optimize where you are specifying the number of records from where the optimize is necessary.
    This number is probably very small between 0 and 400 and every time when you are connecting with admin module you are receiving this message.
    So you have to change that number to be 40000 not more and you will not receive any more that message when you have 400 records you will receive the message when you will have over 40000.
    You can find the parameter also into tbldefault table from your appset.
    I don't remember the name of parameter but you will manage to find out this parameter.
    Regards
    Sorin Radulescu

  • My iphone 4 has no data storage. I have deleted all apps, music and texts and it still says I only have 1.9 GB available. There is nothing in my storage.

    My iphone 4 has no data storage. I have deleted all apps, music and texts and it still says I only have 1.9 GB available. There is nothing in my storage.

    The problem could be that you don't have enough storage on the device itself, not on iCloud.  Go to Settings>General>Usage to see how much "Storage" you have available on the device.  Farther down the list is the available storage on iCloud.
    Also check:
    Go to Settings>iCloud>Storage & Backups>Manage Storage; there, tap the device you need info on and the resulting screen lists Backup Options with which apps store data on iCloud as well.  Tap Show All Apps to get the complete list of apps and MB used for backup storage.
    A device needs many MB of storage in order to perform a backup to iCloud.
    Also see:  http://support.apple.com/kb/ht4847`

  • TREX - Configuring Distributed Slave with Decentralized Data Storage

    I am creating a distributed TREX environment with decentralized data storage with 3 hosts.  The environment is running TREX 7.10 Rev 14 on Windows 2003 x64.  These are the hosts:
    Server 01p: 1st Master NameServer, Master Index Server, Master Queue Server
    Server 02p: 2nd Master NameServer, Slave Index Server
    Server 03p: Slave NameServer, Slave Index Server (GOAL; Not there yet)
    The first and second hosts are properly set up, with the first host creating the index and replicating the snapshot to the slave index server for searching.  The third host is added to the landscape.  When I attempt to change the role of the third host to be a slave for the Master IS and run a check on the landscape, I receive the following errors:
    check...
    wsaphptd03p: file error on 'wsaphptd03p:e:\usr\sap\HPT\TRX00\_test_file_wsaphptd02p_: The system cannot find the file specified'
    wsaphptd02p: file error on 'wsaphptd02p:e:\usr\sap\HPT\TRX00\_test_file_wsaphptd03p_: The system cannot find the file specified'
    slaves: select 'Use Central Storage' for shared slaves on central storage or change base path to non shared location
    The installs were all performed in the same with, with storage on the "E:" drive using a local install on the stand-alone installation as described in the TREX71InstallMultipleHosts and TREX71INstallSingleHosts guides provided.
    Does anybody know what I should try to do to resolve this issue to add the third host to my TREX distributed landscape?  There really weren't any documents that gave more information besides the install documents.
    Thanks for any help.

    A ticket was opened with SAP customer support.  The response to that ticket is below:
    Many thanks for the connection. We found out, that the error message is wrong. It can be ignored, if you press 'Shift' and button 'Deploy' (TREXAdmin tool -> Landscape Configuration).  We will fix this error in the next Revision (Revision 25) for TREX 7.1.

  • File path of open data storage

    Hello all!
    Now I'm using the blocks of open data storage, write data and close data storage for storing and extracting result data. For the file path issue, before I
    set the data path by double clicking the "open data storage" block and inserting the file location in the indicated place, and that worked!
    Now since I made a stand alone application of this program and shall use it in other computers, the file location I inserted in open data storage block isn't
    valid any more in other PCs. So I modified my source code by connecting a "current vi path" to the open data storage block's file path node instead of
    inserting it inside the block, and this doesn't work! During running there shows an error in the write data block saying that the storage refnum isn't valid!
    I'm wondering why I couldn't specify the file path like this. Any way to allow me to specify the file path as the current vi path?
    Thanks!
    Chao
    Solved!
    Go to Solution.

    You need to account for the path changes when built in to an application, have a look at this example.
    https://decibel.ni.com/content/docs/DOC-4212
    Beginner? Try LabVIEW Basics
    Sharing bits of code? Try Snippets or LAVA Code Capture Tool
    Have you tried Quick Drop?, Visit QD Community.

  • Uploading to online data storage: Now cannot download songs into iTunes

    Hello all.
    I am not seeing this one on any FAQs, knowledge bases, or discussion boards yet:
    I am doing my initial upload of files to SugarSync, a highly-recommended online data storage service. Since I started, I cannot download songs into iTunes, even from the iTunes Store.
    On any new downloads from the iTunes Store, the song DOES appear in the Music library view but immediately after completing the download it shows the exclamation point warning that the file is not in its location. The new folders get created properly within the iTunes Music folder but the subfolder where the song should be is empty. Each time I had to write iTunes Support to get them to make the files available.
    I can still add files manually, no problem. E.g., I can add *.mp3 or *.wav files or folders, I can convert them to AAC, etc. The glitch seems to occur only when automated loads into iTunes are operating.
    As a test, I downloaded a song from Amazon. Here the problem was different but I could work around it manually. Normally the Amazon process loads songs automatically into iTunes, too. Here again, the download did create the proper folder in the iTunes Music folder, as it should, but this time the symptoms were reversed:
    (a) the mp3 file WAS in its folder as it should be (w/the iTunes DL, the file was NOT there)
    (b) the song did NOT appear in the iTunes Music view (w/the iTunes DL, the song DID appear)
    (c) I was able to browse to the file and tell it manually to load into iTunes (w/iTunes I had to write Support and wait a day).
    (I wonder what's the cause of the differences between the two cases.)
    Strictly speaking, I can't PROVE the problem has anything to do with SugarSync (which otherwise seems good so far), but the DL problem started as soon as I started using it. Something in the SugarSync upload or file-monitoring process, or an odd thin gin iTunes, seems to be preventing automated, direct loads into iTunes. And since the data service runs in background, so it can monitor file changes, that might mean I can't buy music anymore! Obviously that would be a dealbreaker with SS. (I have contacted SS on this but they've not had fair chance to reply yet.)
    1) Anyone else have this problem?
    2) Is this permanent or just temporary while I am doing the initial upload?
    3) Anyone know a solution?
    (FYI, I am a highly-experienced user and otherwise quite handy with iTunes files, library moves, and backups. My library is entirely consolidated and all AAC.)
    Thanks.
    (Oh, and this occurred in both iTunes 8 and the new iTunes 9, so it seems unrelated to the upgrade this week.)

    UPDATE 1. CHANGING BROWSER HELPED -- OR DID IT?
    I called Apple iTunes Support, who said the problem is new to them. The technician's hypothesis was that something, perhaps browser-related, was interfering with the initial creation of a temporary file (which should go to the Recycle Bin) that instead causes the completed file to go to there.
    He noted that iTunes, though not going through one's browser onscreen, does use settings within one's default browser. I use Mozilla Firefox, so we switched to IE as the default browser, restarted iTunes, and the song downloaded with no problem! Then I switched back to Mozilla, restarted iTunes, and it worked AGAIN with no problem!
    (Dutifully I advised SugarSync, which is still investigating.)
    UPDATE 2: ARTIST NAME CHANGE - SOME FILES GOT MIS-MOVED / MIS-CHANGED
    Definitely something still wrong. This time some pre-existing song entries (not new downloads) lost their connection to their source file.
    In iTunes, which manages folder names for artists and albums automatically, I corrected the spelling for an Artist, so immediately iTunes renamed the folder, and automatically SugarSync noted the change to be uploaded. While the changed folder name and all the songs within were still uploading to SS, in iTunes I saw exclamation points come up -- but only for some of them. Most files got moved or changed correctly, but several lost connection to their file (i.e., the file was removed for the original misnamed folder but never moved into the correctly-named folder). Weird.
    Worse, in only some of those cases did I find the missing *.m4a file in the Recycle bin. (I had to retrieve old, original *.mp3 versions from another folder and re-import each into iTunes manually.) I've never seen iTunes have a problem managing an Artist rename until I started using the live SS process.
    (I've reported this to SS and asked if there is a way to disable temporarily SS to see if that's the problem.)
    [Note: I am willing to try downloads again but I am wary of trying to rename entire Artists (Folder) again. That was a lot of work.]
    ====
    UPDATE 3: SERIES OF TESTS - 1 FAILURE USING iTUNES
    Still problem occurs, but not always. Today, I rebooted PC. I tried CD, iTunes, & Amazon. I varied having the browser open when using iTunes.
    Here are the results of a series of attempts to download songs. "FAIL" means the file did not load properly into iTunes or loaded but lost its connection (exclamation point warning).
    # Source Mozilla #Songs Result
    1 CD Closed 1 OK
    2 iTunes Closed 1 OK
    3 Amazon Open 2 OK
    4 iTunes Open 1 FAIL
    5 Amazon Open 1 OK
    6 iTunes Closed 1 OK
    7 Amazon Open 2 OK
    8 iTunes Open 2 OK
    (I reported this to SS. Hoping they'll test and find the problem.)

  • Append value with Data Storage Vis

    Dear,
    I would like to use the Data Storage VIs to collect my data but I can't achieve my target.
    I'm acquiring 1000 samples at 1kHz (N samples on demand) and I make the mean value of the samples. At the end of this proces I have a scalar value and the initial time at wich I have acquired the data. With this two I build a waveform and then I use the Write Data Storage Vi (TDMS) with "append" write mode to save my data.
    When I read the Data Storage all the value have lost the time information. They start from 1.00.00,000 01/01/1904 and are equal spaced in time.
    How can I keep the time information?
    Thanks

    Sorry totaly misread what you were doing.
    You need to create ensure that waverform that is saved has the correct values for X0 and dx when you save it. Use the build waveform function to acheive this.
    edit:
    the default value for X0 is timestamp 0 (1904), use get datetimestamp at the very start of the cycle to get the correct value.
    James
    Message Edited by James W on 04-21-2010 01:06 PM

  • SR830 data storage for rs232

    Hi,
    I found a LabVIEW code here which can storage data from input signal (e.g.A/I)in SR830 and transfer it by the GPIB.
    I used function generator to generate a sine wave with frequency:30Hz& Vp-p:100mVolt , conencting to SR830.
    Clearly ,I got a correct result when i used the code by GPIB communication interface(left graph).
    Than,I tried to change the communication interface RS232 to accept the same signal,but it has mistakes(right graph).
     Here is original code "data storage for GPIB"
    Here is rewrite code for RS232 by myself,but what's wrong i did?
    Attachments:
    SR830 DATA STORAGE EXAMPLE.VI ‏54 KB
    scan test1.vi ‏43 KB

    The SR830 expects three integer arguments (separated by commas) for the TRCA? query:
    * i = 1 or 2 specifies which buffer to download from
    * j >= 0 specifies the starting point
    * k>=1 specifies how many points to download
    If you know k, you can calculate the exact number of bytes in the response. For your code, which downloads 4000 points at a time, that will be something like 60 kB (if memory serves, the response in ASCII transfer mode is 15 bytes/value). Make sure that you're not hitting any timeout or serial buffer size limits with a transfer of that size.  
    Edit: You have your bitrate set to 9600 baud (1200 bytes/second) and a 10 second timeout. That will read 12 kB before timing out, or 1/5th of your transfer. The 830 supports baud rates up to 19,200, which will help, but you'll also need either a longer timeout or to transfer your data in smaller chunks. 

  • OWA 2007 Issue : Microsoft.Exchange.Data.Storage.VirusMessageDeletedException Could not get properties.

    Hi I am facing an issue with Outlook web access on my production server Exchange Server 2007 with Sp1. When i try to reply or forward a message from OWA it displays The message has been deleted due to a virus threat . Kindly refer to the below error details. I have a box with all 3 roles installed I do not have an Edge Server . IO have installed Forefront on the same Box as my exchange Server.Below is the Detail of  the error . Kindly Help
    A virus was found in this message and it has been deleted. For further
    information, please contact technical support for your organization.
    Click here to continue working.
     Copy error details to clipboard
     Show details
    Request
    Url: https://192.168.7.12:443/owa/forms/basic/BasicEditMessage.aspx?ae=Item&t=IPM.Note&a=Reply&id=RgAAAACFMIZq8d7LTqcPs%2bRZA5g%2bBwBDDZWeCojSQZ1bZZ7Ga%2fkWAAAAeCc6AABDDZWeCojSQZ1bZZ7Ga%2fkWAA5iTbjpAAAJ
    User host address: 192.168.7.11
    User: Munendra Pal Gangwar
    EX Address: /o=First Organization/ou=Exchange Administrative Group
    (FYDIBOHF23SPDLT)/cn=Recipients/cn=mp_gangwar
    SMTP Address: [email protected]
    OWA version: 8.1.336.0
    Mailbox server: PFCDELEXCH01.PFCDOMAIN
    Exception
    Exception type: Microsoft.Exchange.Data.Storage.VirusMessageDeletedException
    Exception message: Could not get properties.
    Call stack
    Microsoft.Exchange.Data.Storage.MapiPropertyBag.GetProperties(IList`1
    propertyDefinitions)
    Microsoft.Exchange.Data.Storage.StoreObjectPropertyBag.InternalLoad(PropertyDefinition[]
    properties, Boolean forceReload)
    Microsoft.Exchange.Data.Storage.StoreObjectPropertyBag..ctor(StoreSession
    session, MapiProp mapiProp, Origin origin, PropertyDefinition[]
    autoloadProperties, Boolean canSaveOrDisposeMapiProp)
    Microsoft.Exchange.Data.Storage.StoreObjectPropertyBag..ctor(StoreSession
    session, MapiProp mapiProp, Origin origin, PropertyDefinition[]
    autoloadProperties)
    Microsoft.Exchange.Data.Storage.Item.InternalBindItem(StoreSession
    session, StoreObjectId itemId, Byte[] changeKey, ItemBindOption
    itemBindOption, PropertyDefinition[] allPropsToLoad)
    Microsoft.Exchange.Data.Storage.Item.InternalBind[T](StoreSession
    session, StoreId id, ItemBindOption itemBindOption,
    PropertyDefinition[] allPropsToLoad)
    Microsoft.Exchange.Data.Storage.Item.InternalBind[T](StoreSession
    session, StoreId id, PropertyDefinition[] allPropsToLoad)
    Microsoft.Exchange.Clients.Owa.Core.Utilities.GetItem[T](StoreSession
    storeSession, StoreId storeId, Boolean forceAsMessageItem,
    PropertyDefinition[] prefetchProperties)
    Microsoft.Exchange.Clients.Owa.Core.Utilities.GetItem[T](UserContext
    userContext, StoreId storeId, Boolean forceAsMessageItem,
    PropertyDefinition[] prefetchProperties)
    Microsoft.Exchange.Clients.Owa.Core.Utilities.GetItem[T](UserContext
    userContext, StoreId storeId, PropertyDefinition[] prefetchProperties)
    Microsoft.Exchange.Clients.Owa.Basic.EditMessage.LoadMessage()
    Microsoft.Exchange.Clients.Owa.Basic.EditMessage.OnLoad(EventArgs e)
    System.Web.UI.Control.LoadRecursive()
    System.Web.UI.Page.ProcessRequestMain(Boolean
    includeStagesBeforeAsyncPoint, Boolean includeStagesAfterAsyncPoint)
    Inner Exception
    Exception type: Microsoft.Mapi.MapiExceptionVirusMessageDeleted
    Exception message: MapiExceptionVirusMessageDeleted: Unable to get
    properties on object. (hr=0x80004005, ec=1294) Diagnostic context:
    Lid: 18969 EcDoRpcExt2 called [length=479] Lid: 27161 EcDoRpcExt2
    returned [ec=0x0][length=422][latency=15] Lid: 23226 --- ROP Parse
    Start --- Lid: 27962 ROP: ropOpenMessage [3] Lid: 17082 ROP Error:
    0x50E Lid: 26977 Lid: 21921 StoreEc: 0x50E Lid: 27962 ROP:
    ropExtendedError [250] Lid: 1494 ---- Remote Context Beg ---- Lid:
    1238 Remote Context Overflow Lid: 14164 StoreEc: 0xFFFFFA1D PropTag:
    0x672D0003 Lid: 8660 StoreEc: 0x8004010F PropTag: 0x672D0003 Lid:
    21970 StoreEc: 0x8004010F PropTag: 0x672D0003 Lid: 23921 StoreEc:
    0x3EC Lid: 21970 StoreEc: 0x8004010F PropTag: 0x672F0014 Lid: 23921
    StoreEc: 0x3EC Lid: 21970 StoreEc: 0x8004010F PropTag: 0x6708000B Lid:
    21970 StoreEc: 0x8004010F PropTag: 0xE960102 Lid: 21970 StoreEc:
    0x8004010F PropTag: 0x6708000B Lid: 21970 StoreEc: 0x8004010F PropTag:
    0xE960102 Lid: 21970 StoreEc: 0x8004010F PropTag: 0x67760102 Lid:
    25394 Lid: 19506 Lid: 27698 Lid: 11285 StoreEc: 0x50E Lid: 21970
    StoreEc: 0xFFFFFC07 PropTag: 0x30080040 Lid: 25818 Lid: 6153 StoreEc:
    0x50E Lid: 25906 Lid: 5249 StoreEc: 0x50E Lid: 1750 ---- Remote
    Context End ---- Lid: 27962 ROP: ropGetPropsSpecific [7] Lid: 17082
    ROP Error: 0x4B9 Lid: 26465 Lid: 21921 StoreEc: 0x4B9 Lid: 27962 ROP:
    ropExtendedError [250] Lid: 1494 ---- Remote Context Beg ---- Lid:
    26426 ROP: ropGetPropsSpecific [7] Lid: 1750 ---- Remote Context End
    ---- Lid: 26849 Lid: 21817 ROP Failure: 0x4B9 Lid: 20385 Lid: 28577
    StoreEc: 0x50E Lid: 32001 Lid: 29953 StoreEc: 0x50E
    Call stack
    Microsoft.Mapi.MapiExceptionHelper.ThrowIfError(String message, Int32
    hresult, Object objLastErrorInfo)
    Microsoft.Mapi.MapiProp.GetProps(PropTag[] propTagsRequested)
    Microsoft.Exchange.Data.Storage.MapiPropertyBag.GetProperties(IList`1
    propertyDefinitions)

    I had this same issue, except I have Symantec mail security not Forefront. It wound up being a line in the adult content filter. For whatever reason, they included "If you received this email" as one of the literal strings. This is probably part
    of almost every corporate confidentiality clause I have ever seen!! go figure......
    Thanks for the event log hint- since I have the adult content set to delete, I had no good tracking mechanism in Exhange or SMSME. I set email notifications for the future on these.
    Brent
    I had this same problem, but I have ESET Mail Security Server. in some one case the problem y solved if I attach the "user@domain" in the "white
    List". But in many case the problem is continuous. I have Exchange 2007 in MS Windows Server 2003.
    Thanks for yours help.

  • Exchange 2010 SP3 UR2 and Event 4999 = AirSync, M.E.Data.Storage, M.E.D.S.AppointmentTombstone

    Hello together,
    i'm having the following event on my cas servers every about 30 minutes:
    Event 4999 MSExchange Common
    Watson report about to be sent for process id: 5780, with parameters: E12, c-RTL-AMD64, 14.03.0151.000, AirSync, M.E.Data.Storage, M.E.D.S.AppointmentTombstone..ctor, System.OverflowException, 7f09, 14.03.0158.001.
    ErrorReportingEnabled: False
    it looks like it is a known bug fixed in SP3 UR3 (http://support.microsoft.com/kb/2891587/de) ?
    http://support.microsoft.com/kb/2888911/de
    they are talking there about a workarround to delete the problematic "thumbstone data". but how to find and identiy them before deletion ?
    "To work around this issue, use the MFCMAPI tool to remove the corrupted tombstone data."
    thanks for feedback,
    best,
    martin

    Hello Martin,
    I have a user who is having this exact same issue. I know this thread is a few months old, did you ever find an answer to where the corrupted tombstone data was located at?
    thanks,
    Emmanuel Fumero Exchange Administrator

Maybe you are looking for