Regarding the Illuminated key function

Im not entirely sure, why but when i attempt to illuminate the keys they wont.
Im wondering does this have to do with the battery? its at about 25% battery health and it doesnt allow me to illuminate the keys, and when i plugged the power adapter in, it also didnt allow me to illuminate the keys either.
does it have to be at a certain percentage to allow me to illuminate the keys at all?
it was working fine the past few days.
it just shows me the little illumination icn with a "NO" symbol
thanks!

Nothing to do with power. There ambient light sensors under both speaker grilles, and it must be dark for the kb illumination to work. Put a magazine over each speaker then try.
You can override the ambient light sensors with 3rd party software:
http://labtick.proculo.de

Similar Messages

  • Regarding the access key for an object

    HI all
    Please clarify me the doubt that an access key will be different for each and every object or one for all the objects.
    regs
    karna

    Hi karna,
    1. It will be different for all objects.
    2. In fact, access key will be different
        for each object,
       and that too, for each different installation number
       as well as each basis version number
    <b>3. In short, access key is dependent upon the combination of
    1. The object R3TR FUGR SFES    
    2. Sap Release (eg. 640)
    3. Installation Number</b>
    4. It means that the access key for one standard program
       (in our server),
       will not work in another server bcos the installation number will be different.
    regards,
    amit m.

  • Satellite U405 - Touching the illumination keys starts the notebook

    When the computer switched off, if I touch any of the illumination/multimedia keys, the computer starts.
    This is especially problematic because the computer starts even when I just close the lid (because the illuminaton keys are actuated by the lid itself).
    Any sugestions? If not how to solve the problem, could you please tell me how to switch them off?

    Hi
    I think Akuma is right and your notebook should be checked from a notebook technician. Maybe the sensor board is faulty and must be replaced to solve this issue. Therefore you can contact the nearest authorized service provider that you can find on the Toshiba US page.
    I assume your notebook is still under warranty, so the repair should be for free.
    But just one question: Did you try a BIOS update?

  • How do I disable the alt key function?

    I have tried to clean my alt key on my macbook keyboard and now my macbook is acting like the key is hold down all the time eventhough it's not. Have tried to play around with the key, but its still the same. I wonder if I can disable the functions of the alt key in the mac os?

    you can do it system preferences->keyboard and mouse->keyboard->modifier keys. set "option" to no action. however, option is really a pretty useful key so you might consider trying to fix you keyboard.

  • Changing the FN key function

    Hello.
    I don't remember how, but I accidentally changed my FN key function to "Show Desktop".
    This means that every time I press "FN" it shows my desktop.
    How do I disable this?
    Thank you very much for your help.
    Itai.

    That was it. Sorry for my easy-to-solve question
    Thank you very much!

  • Regarding the Ref Cursor functional;ity

    HI,
    I am using ref cursor to return Result Set to .Net.
    I am in doubt that , Is it requires multiple server trips to fill the DataSet at front end.
    As my assumption it will return the address of the work area provided in Oracle server. After that for each row it make a server trip .
    Is my assumption is right ?
    Can any one tell me the functionality behind returning a Ref Cursor .
    Thank you....

    This is (or ought to be) configurable on the .NET side. There will be a server round-trip to fetch every N records where N is a setting on the client. I'm not particularly experienced with .NET, so I'm not sure where this setting is set, but the folks over in the .NET forum might.
    Justin
    Distributed Database Consulting, Inc.
    http://www.ddbcinc.com/askDDBC

  • Regarding the cumulative key figure

    Hi gurus,
    We re struck with cumulative keyfigure,we need to sum the amount based on the periods.I will write the sample data how we have to get.
    For Balance Sheet we would like to store cumulative amount and not the movements.
    This is the data actually we re getting in the cube.
    “Gl Acct No”     “Company Cde”   Fiscalyear  Period  amount
    1001100                  0002             2007          01   150                     
    1001100                  0002             2007          01    300   
    1001100                  0002             2007          02    400
    1001100                  0002             2007          02    500
    1001100                0002               2007          03    600
    We need the data to get into the cube based on summing up with periods
    1001100                  0002             2007          01    450 
    1001100                  0002             2007          02    1350
    1001100                0002               2007          03    1950
    Please shed some light on this issue.
    thanks
    kiran

    You have the data in cube in this format (movements), but you can transform this data to the cumulative in reporting time with ranges. You could create a structure with this type of columns/rows
    Jan -> Restrict period to 01
    Feb -> Restrict period with range (01-02)
    Dec -> Restrict period with range (01-12)
    You could create more complex selections in this ranges using offsets or variables in the selection of period
         Actual period -> Restrict period with range (range 01-ActualMonth)

  • Regarding the get pernr function

    Hi guys,
              Got to know that when we use get pernr it automatically checks for the autherization on pernrs to view data.
        Would like to know who all have access to see which pernrs? Can i get any ideas on this....
    Thanks in advance
    Abhi

    Triggers the associated events when data is read in an executable (type 1) program using a logical database.
    node is a node in the logical database that is assigned to the report (type 1 program) in the program attributes. You must declare the node in the report using the NODES statement (or the TABLES statement, if the node is of the type "table").
    The node node corresponds to a data object of the same name.
    node is available for processing during the flow of the logical database. Moreover, you can also make reference to the fields from the node that lie on the access path for node in the logical database associated with the report - unless the node is of the dynamic dictionary type.
    Notes
    You can use the event "GET dbtab." only once in the report.
    The GET events are implemented internally as FORM routines. This makes all data objects declared with DATA local, that is, they are only recognized and addressable within the event. This also applies to AT SELECTION-SCREEN ....
    The logic is somewhat different for nodes of the dynamic dictionary type. You must declare these nodes in the report using the NODES node TYPE type statement. In this case, type a dictionary type from the logical database for the node node - that is, the type of the data object node assigned to the node node can differ in different reports. In this case, the data object node is local to the -GET event and has the structure type. Outside the -GET event, a (global) data object node also exists and has the static type assigned to the node. The actual data is, however, returned in the local field node and is available only within the -GET event.
    Example
    The program uses the logical database F1S which has a structure where the table BOOKING appears below the table FLIGHT.
    NODES: SFLIGHT, SBOOK.
    GET SFLIGHT.
      WRITE: SFLIGHT-CARRID,
             SFLIGHT-CONNID,
             SLFIGHT-FLDATE,
             SFLIGHT-PLANETYPE.
    GET SBOOK.
      WRITE: SBOOK-BOOKID,
             SBOOK-CUSTOMID,
             SBOOK-ORDER_DATE.

  • The "write key" configurat​ion file vi use of "trim string" prior to writing the data can modify any string data written.

    I tried to use the config VIs to record some front-panel settings for later restoration, one of which could be a single space character (part of a string parsing system).
    I soon discovered that whenever I tried to save that single-space value to an INI file, only a null string was saved.
    After doing some digging I discovered that buried in the Write Key vi is a worker vi called Config Data Modify that uses Trim String on the string data before it is written to the file and that's what was eating my string character. I don't know whether this is a bug or a feature but there are at least three ways to fix it.
    1) Assuming you want to leave the library VIs alone, you can pre-process any stings sent to "write key" to replace all spaces with "\20" and then post-process all strings read using "read key" to replace all instances of \20 with spaces.
      and if you don't mind modifying the library VIs, either to save/use under a different name or to stick back into the library in a modified state (caution - can cause problems when you move code to another machine with an un-modified library) then...
    2) You can yank the trim-string out of the Config Data Modify vi and hope that it does not have any undesirable side effects with regards to the other routines that use Config Data Modify (so far I have not found any in my limited testing)
    or
    3)  You can modify the string pre-processing vi, Remove Unprintable Chars, to add the space character to the list of characters that get swapped out automatically.
    Note that both option #1 (as suggested above) and option #3 will produce an INI file data entry that looks like    key="\20Hello\20World\20"   while option #2 produces an entry that looks like   key=" Hello World "
    The attached PDF contains screenshots of all this.
    Attachments:
    Binder1.pdf ‏2507 KB

    Hi Warren,
    there's a 4th option:
    Simply set the "write raw string" input of the write key function to TRUE
    This option only appears when a string is wired to that function!
    Just re-checked:
    I think it's a limitation of the config file format. It's text based and (leading) spaces in the value are "overseen" as whitespaces. So your next option would be to use quotes around your string with spaces...
    Message Edited by GerdW on 05-02-2009 08:32 PM
    Best regards,
    GerdW
    CLAD, using 2009SP1 + LV2011SP1 + LV2014SP1 on WinXP+Win7+cRIO
    Kudos are welcome

  • How to use key() function in XSL Mapper file?

    I would like to use the XSLT key() function in an XSL stylesheet in the XSL Mapper designer, but I can find no way to include the <xsl:key> element.
    key() should be supported as it is available in the component palette, but I can't find a way to add <xsl:key> in the designer, and if I add it manually the designer tells me it is not supported.
    This is with Jdeveloper JDEVADF_11.1.1.3.PS2_GENERIC_100408.2356.5660 on Linux.
    Any help appreciated, thanks.

    The usual practice is to leave the XSLT as such. A person skilled in XSLT would know to open the XSLT in source mode if the design view is not supported. Almost most of AIA XSLTs are such and one has to only open them in source view.
    You might want to document this into some document/guide which the person might refer before actually making the changes!
    Cheers,
    - AR

  • How can I get the tab key to select text fields only?

    Since upgrading to Firefox 4 on Windows, the tab key functions differently. How do I change it so that it only selects text input fields?

    The answer is:  The bug is in the UI.  Speech recognition was enabled, by default it uses the bare escape key as a "mic on" indicator, and it does not leave any trace in the keybord configuration.  So that is the bug.  It needs to leave a trace there, a la: "X Listen-for-voice-command  ^" under Mission Control.

  • Is it possible to find the "Sync" key in my old Firefox files ?

    I have "Backup" files from my old laptop. And there are probably 1000 or more Mozilla and Firefox files in the backup .... is there a way to merge that old information/files with my new Firefox account ?

    Do you have a folder that contains places.sqlite and a bookmarkbackups folder? If so, that should be helpful in reconstructing your settings. This article has tips on that: [[Recovering important data from an old profile]].
    Regarding the Sync key specifically, I don't know where that is stored, but perhaps you won't need it?

  • Why can't I advance a video frame-by-frame with the arrow keys?

    I am able to play a video, and to scrub through by clicking and dragging the play head, but when the video is paused, my arrow keys won't advance frame-by-frame.  Is there a place that I have to enable the arrow key function?  I've looked through the Preferences but didn't see anything.  Anybody know how to get this to work?  Thanks!!

    This forum serves Photoshop.com, the online service.
    For help with the desktop version of Photoshop CS, please repost your question here: http://forums.adobe.com/community/photoshop

  • LICENSE KEY FUNCTIONALITY

    Hi,
    I'm stuck. I've written a piece of software in Java and because of the way java's classes can be reversed
    engineered I want to embedd and run the application on-line via my website say as an applet.
    I read that applets can be very restrictive for example the user of my program will not be able to save
    his work or a file on his hard drive. Thus not too sure how to wrap up the application.
    How can I wrap up my java application such in order to acheive the following.
    1) A license key is generated upon a valid purchase send out to the purchaser via his/her email address
    2) Download my application with the necessary tools as say an icon on the users desktop.
    I outsourced the license key functionality and was told by the programmer that there is no way that the license
    key functionality would stop the user copying it onto another machine or passing it onto a friend - Am I missing
    the point here as I paid for an incomplete solution but surley this should be the case. What are the steps required
    to have safe license key functionality working properly.
    Regards

    opjava wrote:
    I'm stuck. I've written a piece of software in Java and because of the way java's classes can be reversed
    engineered I want to embedd and run the application on-line via my website say as an applet.Running it as an applet doesn't change anything. It will be just as accessible to reverse-engineering as if it were run as a normal application.
    I read that applets can be very restrictive for example the user of my program will not be able to save
    his work or a file on his hard drive. Thus not too sure how to wrap up the application.Unless you use a signed applet, yes.
    How can I wrap up my java application such in order to acheive the following.
    1) A license key is generated upon a valid purchase send out to the purchaser via his/her email address
    2) Download my application with the necessary tools as say an icon on the users desktop.
    I outsourced the license key functionality and was told by the programmer that there is no way that the license
    key functionality would stop the user copying it onto another machine or passing it onto a friend - Am I missing
    the point here as I paid for an incomplete solution but surley this should be the case. What are the steps required
    to have safe license key functionality working properly.There is no absolutely secure way. Since the machine needs to be able to execute the code, it must understand it. Anything that can be understood can be reverse-engineered.
    You can make it (slightly) harder by using a good obfuscator, but that only raises the clue barrier and doesn't produce an unbreakable barrier.
    The only secure way is to never let the user have the code at all. That can be achieved by providing your software only as a web service/web application that you host yourself. This way the user can use the application but never have access to the code.

  • Delete Key Functionality

    According to everything I have read, the keyboard shortcut for sending a file or folder to the trash is Cmd-Delete. This does not work on my computer. The delete key functions as expected within applications, but does not seem to do anything in the Finder. I've tried every combination of Cmd, Option, Control, and Shift with the Delete key, but it doesn't work.
    Any ideas?

    Backspace deletes the previous character and the delete button deletes the next character.
    Dib.

Maybe you are looking for