Registering SPA500 series IP phone with CME 8.6

Hello friends. I'm newbie with CME configuration, but now I'm asked to register SPA504G phones onto a CME 8.6 installed on a Cisco 2911 router using SIP protocol. I'm testing with a SPA 502G phone with software version 7.4.7. Within "voice register global" configuration I can't find "load" command for thisphoone model. About phone files, I only found "spa50x-30x-7-4-8a.bin" file for this phone and loaded into flash: unit.
How can I make SPA 500G phone be registered with this CME? I would appreciate somebody can help me with a guide to achieve this.
Thanks in advance for your help.
Best regards
Joe

I have the same problem.
Can anyone help?
Thank you.

Similar Messages

Need help on displaying the callers name on ip phone with cme using external directory

Hello Guys,
Need help on displaying the callers name on ip phone with cme while using external directory
Thank you,
Khaja

Thanks for your help,
Does it 100% work with CME. We use SIP and 2ring for external directory? Thanks you.

Using nokia's E series of phones with linksys

Hello,
I wonder if it is possible to use one of Nokia's mobile phones (E60,E61,E70 with VOIP features ) with any of the Linksys products? If so, what products are needed?
Grtz,

@ Mountain2k : What kind of scenario are you looking for? Using a Linksys access point/router? Or are you interested in connecting the phone to an SPA9000?
There are two essential pieces to tracking down a problem with your VoIP equipment:
The configuration of every device involved
SIP protocol traces
And don't forget: there's no such thing as giving too much information when describing a problem.

7900 series IP Phone with third party Gateway/PBX system expansion

Hello,
I have a question about 7942G phone and 7937G phone.
A customer wants to add 4x7942G and 1x7937G phone to their existing system.
They currently have third party IP Gateway/PBX system with POE and having Cisco 3x7911G IP phones. Their current install/config is fully operational.
I have few doubts to ask:
Just by adding/connecting/configuring 7942G, 7937G to the existing system will work?
7942G has option for Channels ( CP-7942G-CH1 ---- According to 7942G data sheet) Do customer have to use this model?
Thank you

1. Really should ask PBX system vendor
2. These all are the same exact identical device.

SPA500 series IP Phone and Lock function

Hi experts
Is there any feature/XML application to lock the device?
As far as I know, although not familiar with this type of devices, we can use Extension Mobility but my customer is looking for a more basic application to lock the device and unlock via PIN or similar so no one elase can use in durng device owner absence.

As far as I know, there is no simple way to lock the phone by any method, including the XML application.
The only way I know is EM, but it require full reboot of device during lock and unlock, so it's time consuming and unfriendly way. Also, it doesn't allow automatick lockout of unused phone.
The best way I know is based on "Call barring" feature - it require support from PBX side, of course.
Note that it may violate law to block all calls in some countries. Emergency calls must be allowed all the times in my country.

Blackberry registeration with CME

hi all,
I want to know whether one can install the client on blackberry phone same as nokia e71 and register the blackberry phone with cme via wifi. Can somebody provide the link for the documentation
Regards
Nareh

It seems BlackBerry launched complete product - the BlackBerry® Mobile Voice System that can be integrated with CME:
http://na.blackberry.com/eng/services/business/blackberry_mvs/
Here is Configuration Guide:
http://docs.blackberry.com/en/admin/deliverables/20062/BlackBerry_Mobile_Voice_System-Configuration_Guide--1079341-0901073810-001-5.0.1-US.pdf
What I have noticed from document is that "the BlackBerry® Mobile Voice System integrates your organization's PBX phone system with the BlackBerry® Enterprise Server to extend desk phone features to BlackBerry devices". In other words you will need BlackBerry® Enterprise Server working as well for the system to function.
So I guess to install all it if you have only couple of BlackBerry phones is senseless.
I'm curious if it would be possible to use without BlackBerry® Enterprise Server having just simple client on the phone like Nokia Call Connect, for instance with Nokia E-series phones.

Cisco ip phone 9971 registration failed with CME 8.6 on WAN

Dear Sir
Subject: Cisco ip
phone 9971 registration failed
with CME 8.6 on WAN
I have a WAN simulation with one Cisco2811 router one Cisco1841 router (connected with fast Ethernet interface) plus one layer 2 switch.
I upgraded the 2811 IOS to 15.4M and installed CME8.6, when we tried to add 9971 sip phone If the traffic goes throw LAN (Same subnet- directly from switch to 2811) everything is fine and the SIP phone (9971) added with no problem but when I change the subnet and traffic goes throw WAN
( from 1841 routed to 2811 with default route) my phone didn't register.
It will be great if anybody could help!!
If you can solve my problem, I will be happy to compensate.

Try binding SIP to an interface on which Phone can reach (Use "voice service voip" "sip" and then bind)
Udit

7921 not registering with CME through repeater

I have this environment:
CME 7.0 running in Cisco2851.
WLC2106 with 6 1242 APs
15 phones 7921
I have to extend the wireless coverage to an specific point (warehouse), 150 meters away. This point only have a PC and a phone, so I don't think a bridge is necessary. I have an 1131 AP configured as repeater. In my tests (locally) I see the 1131 is registering to the main wireless network. Using site survey feature in the 7921 I see the SSID broadcast from the repeater AP, but if I use Neighbor list feature the network is not allocated and obviously the phone can't register with CME. Only for tests I had disabled all security features for this SSID.
The 1131 association table only shows the root AP but it indicates the IP address assigned to the controller.
Can somebody give me some tips to identify what I'm missing?
Thanks in advance

I think H-REAP is a feature not usable for this case, isn't
I'm reading the "Cisco Wireless LAN Controller Configuration Guide", in page 7-19 and follow, Workgrouup Bridge is explained. I think it should be the solution for my requirements, although I will test tomorrow (Wendesday), I have some questions:
The example shows a hub in remote site, I guess it can be replaced with a switch without any problem.
Could it be possible to set another AP attached to the switch to get wireless access? Otherwise, I will need a desktop phone.
The manual indicates NO VLAN are supported (page 7-21), so this option will need PC and phone for this site running in the same VLAN?
I appreciate your assistance.
Daniel Escalante.

Where can I find what phone loads are compatible with CME?

I recently upgraded one of our CME systems to CME v10.0
I noticed that even though the CMEv10 Supported Firmware page says the compatible phone load for my 7911 phones is 9-2-1TH1-13,
my 7911's running phone load 8-4-3-16 all seem to be registering and running just fine.
So I must conclude that 7911 phone load 8-4-3-16 is compatible with CME v10.0
Where can I go to find out what phone load versions are compatible with CME or perhaps, at least, where I can find what phone loads are no longer supported by a version of CME?

Hi Jared,
Specific CME versions are tested with the versions listed on the "requirements" doc like the one you mentioned (linked below), but are not limited to those firmware versions. The phone loads/firmware is completely independent from the CME/IOS version. And it is often appropriate to upgrade or downgrade phone firmware levels on CME and is fully supported :)
http://www.cisco.com/en/US/docs/voice_ip_comm/cucme/requirements/guide/cme10spc.html
I would look at upgrading the 8-4-3 firmware for the 7911's BUT you will need to move to an interim mid-point release like 8-5-2 as a first step due to the "important notes" shown here;
Firmware Upgrade Issues for SCCP
Note For all SCCP firmware upgrades from firmware release versions earlier than 8.3(3) to version 8.5(3) or greater, you must first upgrade your firmware to version 8.5(2). Once you have upgraded to version 8.5(2), you can upgrade your IP Phone to version 8.5(3) or later.
http://www.cisco.com/en/US/docs/voice_ip_comm/cuipph/firmware/8_5_3/english/release/notes/7900_853.html#wp57602
Cheers!
Rob

A friend created 3 accounts on his iPhone 5 but forgot the passwords. He can't reset the password as yahoo address is no longer valid. Erasing the phone doesn't solve the issue. How to register the phone with Apple?

A computer illiterate friend created 3 accounts on his iPhone 5 but forgot the passwords. He can't reset the password as his yahoo address is no longer valid. Erasing the phone doesn't solve the issue as the Apple server identifies the hardware as registered. How to register the phone with Apple?
I helped him create a new email address and new iCloud account on my Mac but when we try to register the phone with Apple it says: Maximim accounts limit reached for this device. How can he register the phone? I read different threads and found out that only Apple care can do that. We're in Romania and don't know where to call. Any suggestions on how we fix this?

When I checked the support site for Romania, you apparently don't have an Apple Care contact center. You "may" try calling the US Apple care number to verify the account and have the password reset sent to a different email address. 800-694-7466

How does one register a non apple phone number so as use ichat and texting with that phone number?, How does one register a non apple phone number so as use ichat and texting with that phone number?

How does one register a non apple phone number so as use ichat with that phone?

Have you tried applying the update by going to Help>Updates within Photoshop Lightroom? The update should be using the same licensing? Did you perhaps customize the installation location? Finally which operating system are you using?

HT1688 how can i register my phone with apple to obtain my 1 year warranty

how can i register my phone with apple to obtain my 1 year warranty

The one year standard hardware warranty comes with iPhone. No registration required.
If you have purchased AppleCare Protection Plan (APP) or AppleCare Protection Plan Plus (APP+) during the purchase of your iPhone, it is Auto-Registered if you purchased it at the Apple Retail Store or Apple Online Store.
If you purchased the boxed APP or APP+ from Apple or any reseller, you will need to go to supportprofile.apple.com and sign in with your AppleID username and Password.
You will need to register your Serial Number (found on iPhone Box or in Settings>General>About) and then register your APP or APP+ with the slip of paper that came in white box with the red Apple Logo.
Hope this helps!

Are 300 Series switches compatible with pre-standard PoE detection in old Cisco phones?

Are 300 Series switches compatible with pre-standard PoE detection in old Cisco phones? They don't seem to be (a 7902G won't power on when connected to an SF302-08MP with firmware version 1.1). Is any special configuration needed on the switch to enable this detection?

Please note that the 200 and 300 Series switches now support Cisco Legacy POE as of September 2011, allowing it to deliver power to 7960, 7940, and other pre-standard phones and APs. Details provided at the following link:
https://supportforums.cisco.com/docs/DOC-18337

I bought few years ago a Creative Suite Design Premium and when I want to register my series number, yours services say that the number is invalid. I very surprise because I used it before on a PC computer that doesn't work anymore. I change my computer

I bought few years ago a Creative Suite Design Premium and when I want to register my series number, yours services say that the number is invalid. I very surprise because I used it before on a PC computer that doesn't work anymore. I change my computer with a Mac. Can You verify the number you customer services gave me, L. Fernandes : <serial num removed-kglad>. I give you my phone number in Paris : <phone num removed - kglad>. Best regard. Chantal

http://helpx.adobe.com/creative-suite/kb/error-serial-number-valid-product.html
p.s. this is a public forum. posting your phone number is a bad idea and posting your serial number will get it banned (or used by someone else and unavailable to you).

Help me choose a phone with Whatsapp (it ain't eas...

So... After being a smartphone lLumia dood for a loong time i am now ditching smartphones all together. I dont use facebook anymore and i want a nice slim candybar phone with long battery life, no touch, dual sim and whatsapp. Thats all i want. Simple? No!
My Main sim is 3G so the phone need to support this (because most 2g phones won't use EDGE/GPRS data on 3g cards as it is now).
I thought at first that i could use the Asha 206, but no. It is only 2g.
I would have loved the Nokia 225, but it does not support whatsapp. Why!!!?????
220 was also an option, but here again no 3G
210 was also an option but it is not available in my country and its crazy expensive for what you get.
HELP ANYONE?

Both the Nokia 225 and Nokia 210 do not offer 3G either. Did you consider a Nokia 208, Nokia 301, or Nokia 515? However, WhatsApp is limited in those ‘Nokia Series 40’ based phones, for example smilies+text. Furthermore, you are not going to get any long battery life either – WhatsApp = always online.

Registering SPA500 series IP phone with CME 8.6

Similar Messages

Maybe you are looking for