Regular loss of successful Airport iTunes set up - ? AE glich only

Hope I'm not duplicating. I have followed many of the strands regarding this.
I have one PC and a Brother printer networked onto a Belkin ModemRouter via ethernet, I have then successfully joined a laptop wirelessly to this with WAP-PSK security. I want AE simply for iTunes, to stream wirelessly to a Yamaha amp via a Belkin optical cable.
After all the same set up distress suffered by others I finally got there and the outcome was superb.
However I am plagued with the AE 'dropping off the network' if I restart PC's or ModemRouter and often spontaneously. It can remain green or go to flashing orange, but cannot be found with Airport Admin etc.
Invariably unplugging the AE and plugging back in cures it in 5 mins with AE visible and speakers accessible, but this misses the point.
I have tried all the previous advice:-
Installed AE setup,AE for windows and ModemRouter updates
Removing Win control over wireless networks
Trials with all firewalls disabled,ZA disabled and AE added to Trusted zone of Zone Alarm
Checked all security settings for compliance
Tried different channels
Have also tried manually assigning IP addresses (had prior trouble with IP's duplicating) and MAC addressing each item
Turned internet off
All this to no avail and very tempted to just go for ethernet. Finally I have gone to factory resets on the router and the AE and gone back to auto DHCP. The reconfiguration lasted ony one evening. Both PC's have lost contact and typing in the IP address of the AE manually produces error 6753 from Airport Admin. I cannot find this.
Surely if all the above has failed and a simple AE unplug/replug to power works it is an AE internal glich cured by restart?
Acer Aspire 1700 Windows XP Belkin Modem Router

The AirPort Express will "join" virtually any wireless network if it is provided with 3 correct settings:
1) The name of the wireless network being joined....I assume that you already know this
2) The password of the wireless network being joined....I assume that you already know this
3) The exact type of security settings of the wireless network being joined.....this is where users have difficulty with the AirPort Express setup....because they either use the default settings on the Express (which may likely not match the settings on your wireless network), or they guess at the wireless security setting (which do not match the security settings on the wireless network).
So, the main question here is.....do you know exactly what type of wireless security that your network is using? The Express must be provided with those exact settings in order to join the network correctly.
You will need to perform a Factory Default Reset on the Express and then start over with the configuration again.
Power off the Express for a few minutes
Hold in the reset button first, and keep holding it in for another 9-10 seconds while you simultaneoulsy plug the power back in to the Express
Release the reset button after the hold period and allow a full minute for the Express to restart to a slow, blinking amber light

Similar Messages

HT202213 Homesharing. I had my iTunes set up to play music through my receiver & speakers upstairs. I have airport with RCA plug ins to my receiver auxiliary jacks. Homesharing is on & everything checks out but it no longer works. Any suggestions?

I had my iTunes set up to play music through my receiver & speakers upstairs. I have airport with RCA plug ins to my receiver auxiliary jacks. Homesharing is on & everything checks out but it no longer works. Any suggestions? I have no firewall & I have removed Smith clean program to fix this issue. I am running OS 10.8.2

I called AppleCare this morning and Sean helped me out in a huge way. In all of my attempts, I had not done a factory-default reset on the main base station and apparently some sort of endless loop had occurred between those two stations. Sean was very helpful and patient with me, but now the system is working as promised. Moral of this story is if a factory default rest doesn't help on the "problem" base station, try resetting all of the units.

Just purchased a ipad2, could not us it on my MacBook 10.4.1 - Purchased and installed OSX Snow Leopard 10.6.3 - downloaded and installed latest itunes, set up a itunes accounts and tested by purchasing an album and app, ipad does not show in devises?

I just purchased a ipad2, it would not work on my MacBook 10.4.1 I purchased and installed OSX snow leopard 10.6.3 downloaded and installed the latest itunes, set up an itunes account, purchased some music and apps. When i plug in my ipod it shows up and works, but when i plug in my new ipad the ipad screen comes up with a display of a cable and itunes but does not show in devises, i have tried all the resets and different USB ports with no success. Any ideas short of selling it on ebay or buying a new computer?

If you've already tried the usual rebooting of the computer and ports and stuff, there is only a few things left I can think of. It's possible that when you updated iTunes it didn't fully replace all the files, so I suggest just manually removing iTunes and then reinstalling it.
Try removing iTunes manually first http://support.apple.com/kb/HT1224 then download a fresh copy, make sure it is 10.3.1
It is essential that you go through Finder to remove those files it mentions. Otherwise they won't be reinstalled when you run the installer again.

Airport/iTunes loud static burst

I have an airport express set up to play iTunes. Occasionally when switching tracks I get a really powerful static noise burst, it's deafening. Imagine you have a receiver, you switch to a station with nothing but static, mute the channel, turn the volume all the way up, then suddenly unmute it. Thats what it sounds like. It's happened maybe thrice in the past 3 months. I'd like to fix this because I'm worried this burst is loud enough to damage the speaker. Any suggestions or solutions would be appreciated. my setup itunes>optical>DAC>power amp.

Does the noise burst still occur if you substitute a pair of stereo headphones into the audio port of the AirPort Express? If so, then the issue may be one of three things: 1) Audio source, 2) The power source the Express is connected to, or 3) The Express itself.
If it doesn't then the issue may be: 1) The digital optical audio cable between the Express and the DAC, 2) The DAC itself, 3) The analog audio cable between the DAC and the power amp, or 4) The power amp itself.
One known issue with the Express is that it doesn't have a local clock circuit. As such, when the incoming data is interrupted, as it is when you change songs in iTunes, there is no longer a digital output to feed the DAC, which loses lock as a result. Some external DACs are more sensitive to this than others.

Here's the exact scenario with it: 1) Ipod connected successfully to iTunes. 2) Drag song from Library(in AAC format) to My Ipod. 3) Song plays successfully in iTunes. BTW: This is one of the songs from my cd. Not bought. 4) Eject Ipod. 5) Find song in

Here's the exact scenario with it:
1) Ipod connected successfully to iTunes.
2) Drag song from Library(in AAC format) to My Ipod.
3) Song plays successfully in iTunes.
BTW: This is one of the songs from my cd. Not bought.
4) Eject Ipod.
5) Find song in Ipod and press play.
6) Display for song and time appear.
7) About 1/3 of a second of the song plays, then it cuts out and restarts itself. (boots me back to apple logo)

Nope - and it was set to not look for them.
The final clue came when I tried hooking the drive directly to the computer, instead of to the airdisk. iTunes still hung. Then I disconnected the drive and tried to run it, and iTunes came up right away - but with an ! next to each song. Clearly it was trying to find/touch every file in the library on first startup.
I didn't try plugging in the drive and leaving the hanging iTunes running for more than a few minutes, so it's possible that it would have recovered and launched. But after removing the XML file, restoring the library to my pre-7.7 version, I could hear it accessing the directly attached drive (and see it in disk activity in the monitor) for a few minutes (less than I'd left the hanging one trying), before it came up.
Conclusion:
1) 7.7 is definitely trying to touch/see all the files in the library on first launch (proved by the ! when they are missing).
2) Disconnecting/interrupting the touch/see MAY have corrupted something (can't prove it).
3) Since touching 10,000 files takes a LONG time even at 802.11n speeds (let alone b or g), it's worth the hassle to plug the drive in directly for the first time.
4) Patience is a virtue

Is it possible to get regular computer audio via AirPort Express?

Is it possible to get regular computer audio (audio from websites, MacBook, etc.) on my speakers which are connected to my AirPort Express? Or is the only audio I can hear on my connected speakers the music that is on my iTunes?
Just obtained AirPort Express last night and was dissapointed that only the music on my iTunes plays on my connected speakers and not the normal/regular audio from websites and/or my MacBook.

Hello Brody675. Welcome to the Apple Discussions!
Check out Rogue Amoeba's AirFoil.

I have itunes set up on a PC with all my music, apps, etc. I want to stop using PC and move my iTunes and files to a Mac I bought and synch my iPhone with the Mac. Can I just synch iPhone with Mac iTunes and will it copy all my stuff onto Mac, or will I h

I have itunes set up on a PC with all my music, apps, etc. I want to stop using PC and move my iTunes and files to a Mac I bought and synch my iPhone with the Mac. Can I just synch iPhone with Mac iTunes and will it copy all my stuff onto Mac, or will I have to copy files from PC onto Mac?

Here are some of the links to get you started.
https://discussions.apple.com/thread/3727530?start=0&tstart=0
http://support.apple.com/kb/HT4527
http://www.macworld.com/article/1146958/move_itunes_windows_mac.html

I have itunes set up to sync with my Ipod Touch and my Ipad. As of today, it keeps looking for an iPhone to sync with and give me an error message. I don't have an iPhone and don't know how to stop it from popping open with this error message.

I have Itunes set up to sync with my Ipod touch and Ipad. As of today, iTunes has started searching to sync with an iPhone, which I don't have and pops open with an error message stating it cannot locate the iPhone to sync. I have looked in devices and only the iPad and iPod Touch are listed. Any ideas on how to stop iTunes from searching for any iPhone it is never going to find? It is annoying to have it popping up all the time with the error message. Thanks in advance for any suggestions.

You should really read the manual.
"How do you restore from backup? "
Restore. When given the choice, choose to use backup.
"And how can I check to see if the pics and videos are on my computer somewhere first??"
They would only be where you put them. What program did you use to import them? Pics/vids taken with ipod are not part of the sync process at all. You should be importing them just as you would with any digital camera.
If you did not import them, then they are not on your computer.

How do I do this to use OVerdrive media on deviceThe Apple device must be formatted for use with Microsoft Windows. The iTunes setting 'Manually manage music-' must be enabled for the device before you can complete the transfer.

I cannot make these directions work
I downloaded media on Overdrive MEdia on my PC
I have the overdrive media ap on my I pod touch 4g
this media is suppossed to be compatible w/I pd touch
Notes on Transferring OverDrive MP3 Audiobooks…
Most MP3 capable devices should play OverDrive MP3 Audiobooks.
If you intend to transfer OverDrive MP3 Audiobooks to an Apple® device, note the following…
iTunes® v9.0.2 (or newer) is required.
The Apple device must be formatted for use with Microsoft® Windows®.
The iTunes setting 'Manually manage music…' must be enabled for the device before you can complete the transfer. Adjust this setting in iTunes as follows…
Connect the iPod® to your computer.
If it does not launch automatically, open iTunes v9.0.2 (or newer).
In iTunes, locate the device in the left vertical navigation panel (under heading 'DEVICES'), and click the device.
The 'Summary' screen is displayed.
Place a checkmark next to 'Manually manage music…'.
Click the 'Apply' button.
The iTunes 'Summary' screen refreshes, and the changes are saved.
If desired, close iTunes.
Note that if an Apple device is connected to your computer, you can choose to simultaneously transfer a title to the iTunes Library and the Apple device. If you wish to only transfer a title to the iTunes Library, you must first disconnect the Apple device

Recovering your iTunes library from your iPod or iOS device: Apple Support Communities
Also you said " I want to add them to my iCloud, and also back to my computer. " Note that unless subscribe to iTunes match, only iTunes purchases are stored in iCloud.
Also,
You can redownload most iTunes purchases by:
Downloading past purchases from the App Store, iBookstore, and iTunes Store

ITunes set up gives an error message saying not a "valid win32 application"

I am using Windows 7 and trying to download iTunes, but when I try to open the iTunes set up it gives an error message saying that it is not a "valid win32 application". It does the same for downloading quicktime. I have no idea what this means or what to do about it.

That suggests that the installer is getting damaged during the download.
I'd first try downloading an installer from the Apple website using a different web browser:
http://www.apple.com/itunes/download/
If you use Firefox instead of IE for the download (or vice versa), do you get a working installer?

Unable to install iTunes after converting from Windows Vista to Windows 7. Am told installation was successful, then "iTunes was not installed correctly", followed by "Error 7 (Windows error 193).

Unable to install iTunes after converting from Windows Vista to Windows 7. Am told installation was successful, then "iTunes was not installed correctly", followed by "Error 7 (Windows error 193). I have my iPod plugged into my computer via USB port. What am I doing wrong?

i have the only account on my laptop so have checked and am the account administrator
i run windows 7 home premium
I have the same problem and
have followed the link uninstalling in the correct order,
then restarted as per instructions,
went to Apple to download itunes,
hit download now,
Visit the iTunes download page. Click Download Now to download the iTunes installer. When prompted, click Save (instead of Run).
did not get a save instead of run prompt
Right click on iTunesSetup or iTunes64Setup (the installer you downloaded in step 3).
If you have Windows Vista, Windows 7, and Windows 8: Choose "Run as administrator."
i can only click run as administrator from right clicking the shortcut on my desktop screen
If iTunes fails to install or repair, it might be necessary to remove components left from a previous installation of iTunes and then reinstall.
sick of doing this
at least 7 or 8 times i have re installed itunes to no avail
troubleshooting no better
please help. pulling my hair out at this stage
it was working fine until 2 days ago when i opened itunes it offered to update to 12.1
not working since i clicked yes
also i have gone to restore previous point and ffs there are no restore points before my multiple reinstalls
really dont want to have to restore factory settings

I plugged into iTunes and now all my notes on my phone are gone. Years worth of notes. Can someone tell me what to do to get them back?? I have iTunes set to back them up but can't find out how to retrieve them.

I plugged into iTunes and now all my notes on my phone are gone. Years worth of notes that I stupidly don't have saved anywhere else. Can someone tell me what to do to get them back?? I have iTunes set to back them up but can't find out how to retrieve them.I plugged into iTunes and now all my notes on my phone are gone. Years worth of notes. Can someone tell me what to do to get them back?? I have iTunes set to back them up but can't find out how to retrieve them.

After you restore from backup, you MUST sync to restore your iTunes content. No iTunes content is included in the iPhone backup. Your apps should be in your iTunes library, just sync them back to your phone. If for some reason your apps are not in your library, you can re-download them for free:
http://support.apple.com/kb/ht2519

What can I do simply to keep all my previous contents, (own pics, videos, etc.) on my previously authorized iPad on PC, but get a new authorisation and a right syncronization, without data loss with a new iTunes on my new Mac?

Friends,
I already had an iPad(1) and its full contents (not only the purchased items, applications from Apple, but my all own pics, videos, songs etc.) is normally syncronized with an authorized PC (Windows) computer.
Now, I've bought a new MacBook Air computer, and want to sell my PC. But I don't know how to transfer (or syncronize) all of the contents from my previous iTunes on PC to the new one on the Mac.
When I connected my iPad to my new MacBook Air, I promted, if I want to change authorization of my iPad to the MacBook.
But also got a warning, that the new iTunes will delete from my iPad all my previously syncronized items, pics, videos and music, with the previously authorized iTunes on the previous computer, expect the saved pics from the net.
What can I do just like that, simply to keep all my previous contents on my iPad, but have a new authorisation and a right syncronization, without data loss with the new iTunes on my new Mac?
Thanks a lot for your answer.
([email protected])

Here are some instructions that I have posted several times that may be helpful to you as they have been to others. You can simply ignore anything that does not apply or that you have already done.
As Alan stated above - transferring the iTunes library is the best first step. If you can transfer the iTunes library to the Mac, most of this will be unecessary for you to do.
Very Important ....
1. Authorize the computer.
2. Turn off auto sync in iTunes
3. Transfer purchases
The text in italics is from the other thread - non italics are my words.
The following was copied from this thread. This is essentially what you want to accomplish.
https://discussions.apple.com/message/11527071#11527071
1) Without connecting your iPad to your new computer, start iTunes. Click on iTunes. Click on Preferences. Click on Devices. Check the box next to "Prevent your iPod etc. from automatically syncing." Click OK.
2) Now connect your iPad to your computer and start iTunes.
3) When iTunes starts, right click on your iPad under Devices in the left column. Select Transfer purchases etc.
4) After it finishes transferring all your apps to your computer, right click on your iPad and select Backup your iPad.
5) After it finishes backing up your iPad, right click on your iPad and select Restore etc.
6) After it finishes restoring, left click on your iPad , then click on the Apps tab on top, and check the box next to Sync Apps, then click on Apply below.
If everything on your iPad looks good after the sync, go back and click on iTunes / Preferences / Devices and UN-check the box next to Prevent your iPod etc. The only other thing you may want to check is if your contacts, bookmarks, etc. are syncing correctly now. If not, go to the Info tab after connecting and make sure you indicate which features you want to sync with what sources.
Read this thread and the support links as well. There are apps that you can purchase that will allow you to transfer photos from the iPad to your computer. Look at Photo Transfer App in the App store and you can search for others as well.
https://discussions.apple.com/message/13016026#13016026
This support site will help you with transferring iTunes music to your new computer.
http://support.apple.com/kb/HT4527
One final note - you may want to leave auto sync turned off - but that is totally up to you. I never did use auto sync.

HT1725 What do I do if only part of a song I purchased actually downloaded successfully and itunes is saying it downloaded successfully?

What do I do if only part of a song I purchased actually downloaded successfully and itunes is saying it downloaded successfully?
The song is supposed to last for 2mins 46sec but it cuts out less than a min in to the song.
There is no notification that the download was unsuccessful or incomplete and the 'search for available downloads' option comes back that all songs are downloaded.
What can I do without having to purchase the song again?

Depending upon what country that you are in (music can't be re-downloaded in all countries) have you tried deleting it from your iTunes library and redownloading it via the Purchased link under Quick Links on the right-hand side of the iTunes store home page on your computer's iTunes ? If it's still in your iTunes library then iTunes will assume that it doesn't need re-downloading. Re-downloading.
If you aren't in a country where you can re-download music or if it re-downloads in the state then try the 'report a problem' link from your purchase history : log into your account on your computer's iTunes via Store > View My Account and you should then see a Purchase History section with a 'see all' link to the right of it ; click on that and you should see a list of your purchases ; find that song and use the 'Report a Problem' link.

Ipad shows all regular Iphone inbound calls as Facetime. I only want true FT calls to appear. I switch audio/video and it still happens. How can I set the Ipad to only register true facetime calls rather than all inbound regular calls? thanks

My Ipad will show all regular inbound calls, from Iphone, as Facetime calls. I would like only TRUE facetime calls to appear. I have switched audio/video on Ipad but it still happens. How can I set the Ipad to only register only true FT calls rather than all inbound calls that a re not facetime calls? Yes, you may have to reread this twice and slowly to understand..... Thanks!

Hi webn,
I understand that you do not wish to see phone calls on your iPad anymore. I have an article for you with some information on accomplishing this goal:
Connect your iPhone, iPad, iPod touch, and Mac using Continuity - Apple Support
https://support.apple.com/en-us/HT6337
Turn off iPhone cellular calls
To turn off iPhone cellular calls on your iPad or iPod touch, go to Settings > FaceTime and turn off iPhone Cellular Calls.
On your Mac, open the FaceTime app and go to FaceTime > Preferences. Click Settings and deselect the iPhone Cellular Calls option.
Thanks for coming to the Apple Support Communities!
Cheers,
Braden

Regular loss of successful Airport iTunes set up - ? AE glich only

Similar Messages

Maybe you are looking for