Reinstalling Windows 7 to New Hard Drive with only the Win 7 Upgrade Disc?
So I have an e9180t which like clockwork freezes up after about an hour or two after booting up. I thought it might be the curse of the bad motherboards they came with, but I am hoping it is something else so testing everything I can. I noticed it does not freeze up when booted in safe mode with networking. The hard drive did fail the SMART test so I am wondering if it's time to replace it and if that has something to do with the crashing. I can move cursor, but no apps will open and eventually everything becomes unresponsive causing be tohit the power button to reboot. I already stopped all unnecessary start up programs and it still will freeze in non safe mode.
The PC came with Vista and I believe that's what is on the backup partition on the HD. I do have the Win 7 Upgrade disc from HP. My questons are-
1. If I buy a new HD will the 7 upgrade disc be enough to install full version of Win 7?
2. Anything else I need to do when I install new HD besides reactivate Windows?
Thanks.
This question was solved.
View Solution.
Hi Mike,
Did you create an HP recovery disc set for reinstalling the factory image when the HDD is replaced?
It sound like you may have a problem creating the recovery discs now.
A Smart HDD test failure points to a failing HDD. The symptoms you are experiencing are most likely caused by this fact. You may also have a motherboard or other hardware problem.
You have the Win 7 Upgrade disc and product key.
I am fairly sure the Win 7 upgrade has to be initiated from within Win Vista. The Win 7 upgrade is a full install of Windows so that is not the problem. But it may not run setup unless you start the upgrade in Win Vista. Normally a Win 7 upgrade is started within the current operating system, Win 7 setup validates the existence of a qualifying operating system, and then prompts a reboot to finish the upgrade installation.
You can replace the HDD and try to install Win 7 cleanly. If that fails and you don't have the Vista recovery discs you can purchase an HP recovery disc set here. There are three different builds available. Select the one that matches the factory installed operating system.
You may have one other issue upon replacing the HDD with a newer Advanced Format HDD. Please see this HP Support document for more information.
If you cannot install the Win 7 upgrade cleanly or Win Vista because of the Advanced Format HDD issue, you may have to purchase an OEM copy of Win 7.
Jaco
****I am not an HP employee****
Please give a" Kudos, Thumbs Up" if advice received is relevant or" Accept as Solution" to assist other forum users having a similar problem.
Errare humanum est.
Similar Messages
-
How can I completely wipe the hard drive with out the Mac OS X disc? I don't need any of the info on the computer.
You can't unless you have a bootable system on an external drive you can use. Otherwise, you need either the original disc that came with your computer or a retail copy of Snow Leopard DVD. The latter contains 10.6.3, so your model must be capable of booting from that or an earlier version of OS X.
You can purchase replacement discs from Apple:
Apple Store Customer Service at 1-800-676-2775 or visit online Help for more information.
To contact product and tech support: Apple - Support - Contact Apple Support.
You can purchase Snow Leopard through the Apple Store: Mac OS X 10.6 Snow Leopard - Apple Store (U.S.). The price is $19.99 plus tax. You will be sent physical media by mail after placing your order.
After you install Snow Leopard you will have to download and install the Mac OS X 10.6.8 Update Combo v1.1 to update Snow Leopard to 10.6.8 and give you access to the App Store. Access to the App Store enables you to download Mountain Lion if your computer meets the requirements. -
Load Leopard on a New Hard Drive with Windows XP already loaded
How can I load a new, fresh Leopard operating system on a new hard drive, with Windows XP already loaded and working on it's own independent hard drive via bootcamp beta. I have been using Tiger on it's own drive and wish to discontinue Tiger and move to Leopard without reloading windows. Can I just put in a new drive, and load Leopard with the Windows drive in place?
Please, any suggestions would be appreciated.
Mac Pro Mac OS X (10.4) Runing Windows and Mac operating systemsMalcolm:
Thanks so much for replying to my question! I am new to MAC and have Tiger and Windows XP on separate drives. I will be removing the drive with Tiger and putting in a new drive to load Leopard and I wondered how that would effect accessing Windows XP since the Windows drive will remain in the system. Is there anything I need to do with bootcamp, since Windows was loaded using the Beta version of bootcamp, and bootcamp icon currently shows in the Windows XP taskbar. Tiger was pre-loaded when the computer was purchased. In fact I had to backdate the beta bootcamp version in order to get it to work. I hope this is not asking too much, but I wondered if there would any problem with Windows after the Leopard load.
THANKS IN ADVANCE!! -
I had a repair done on my MacBook Pro and had to have a new hard drive installed. The Apple Auth Repair Shop then updated the OS from 10.6.8 to 10.7.5. Now my iPhoto v 9.2.3 will not open and it sounds like it will not work with this OS. Can you please advise?
You may need many other updates to retain compatibility with Lion. I suggest you reinstall Snow Leopard. Unfortunately, you will need to erase the drive first. Be sure to backup your data if you haven't done so already.
Clean Install of Snow Leopard
Be sure to make a backup first because the following procedure will erase
the drive and everything on it.
1. Boot the computer using the Snow Leopard Installer Disc or the Disc 1 that came
with your computer. Insert the disc into the optical drive and restart the computer.
After the chime press and hold down the "C" key. Release the key when you see
a small spinning gear appear below the dark gray Apple logo.
2. After the installer loads select your language and click on the Continue
button. When the menu bar appears select Disk Utility from the Utilities menu.
After DU loads select the hard drive entry from the left side list (mfgr.'s ID and drive
size.) Click on the Partition tab in the DU main window. Set the number of
partitions to one (1) from the Partitions drop down menu, click on Options button
and select GUID, click on OK, then set the format type to MacOS Extended
(Journaled, if supported), then click on the Apply button.
3. When the formatting has completed quit DU and return to the installer. Proceed
with the OS X installation and follow the directions included with the installer.
4. When the installation has completed your computer will Restart into the Setup
Assistant. After you finish Setup Assistant will complete the installation after which
you will be running a fresh install of OS X. You can now begin the update process
by opening Software Update and installing all recommended updates to bring your
installation current.
Download and install Mac OS X 10.6.8 Update Combo v1.1. -
How to install Windows 7 on new hard drive?
I have changed the old hard drive (500 gb) with a new hard dirve (1 Tera), and now I have two problems: -
1. How do I install Windows 7 on new hard drive?
2. My laptop was pre-installed Windows 7 Pro, but all the DVD kit (Application & Drives Recivery Disc + Operating System Revocer), which was provided (by Lenovo) for the laptop is in the Windows 8 Pro. So how do I install Windows 7 Pro, in my laptop while all DVD kits are in Windows 8 Pro?
by the way this is my laptop spec (for reference) ; -
* Note *
I plan to install Windows 7 Pro in my new hard drive using another Windows 7 DVD (Not DVD provided by Lenovo), but how do I get all the Leveno program which found within the 'Application & Drives Recivery' disc (such as ; - Lenovo System Health and Diagnostics, Lenovo Power Control,Lenovo's Fingerprint Reader) to install in that hard drive? (as I tell you before, all the DVD kit is in or only for Windows 8 Pro)
I hope somebody will help me answer my question,
Thank You
Solved!
Go to Solution.I got the solution;
Answer to question 1 ; using a backup & recovery software to clone my current OS, then transfer to my new hard drive.
Answer to question 2 ; download all the Drivers and software ( all the application that located on the DVD kit that I have) on Lenovo Official Website.
or other solution, send it to a computer service shop and let the experts ( the workers) install it for me ( the most simple and safe way). -
i see that i have a problem after installing my new hard drive on my macbook pro mid 2009 version. I put a new hard drive, with all of my information from my old drive installed on it, into the computer. but now have the blinking question mark folder. I see that it means that it isn't reading the new hard drive.
did i miss a step between transferring all of my information from my old hard drive to the new hard drive and installing the new hard drive into the computer. I believe that i installed properly. it was quite easy.
thanks for your helpIt means there is no bootable system on the drive. If you still have access to the old drive, then I suggest you boot from it then clone it to the new internal drive. Use OPTION boot to boot from the Recovery HD on the old drive:
Boot to the Recovery HD:
Restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
1. Select Disk Utility from the main menu then press the Continue
button.
2. Select the destination volume from the left side list.
3. Click on the Restore tab in the DU main window.
4. Select the destination volume from the left side list and drag it
to the Destination entry field.
5. Select the source volume from the left side list and drag it to
the Source entry field.
6. Double-check you got it right, then click on the Restore button.
Source means the external old drive. Destination means the new internal drive. -
How can the number of computers used for an iTunes account be updated? I had to reinstall itunes on a new hard drive it and counted as an additional computer, against my 5 total computers.
wait until you reach the limit of five authorized machines. then, once a year, you will be able to deauthorize all machines, following which you can reauthorize those computers you currently use/have access to.
click here for more information. -
I just got a new hard drive, iCloud only remembered a handful of my music...
I just got a new hard drive, iCloud only remembered a handful of my music and, I don't know how to get the music from my iPhone back into my iTunes library. I want to put new music onto my phone and, I want to make some new playlists and edit some mistakes I found on the songs on my iPhone.
Please help? I am practically in tears here; I am a part-time DJ and do not need this kind of stress.
I do not want to hear that my iPhone is not a back-up device; I just want my iTunes library and the iTunes on my phone to have all the same music so that I can make playlists with everything and such.DrizzyBaby wrote:
I just got a new hard drive,
Old hard drive is?
Please help? I am practically in tears here; I am a part-time DJ and do not need this kind of stress.
So as a part time DJ, your music is not important enough to back up?
I do not want to hear that my iPhone is not a back-up device;
It’s not.
Bad hard drives (and important info) are two reasons you back up your computer regularly.
You do back up your computer regularly, correct?
See this ->Recover your iTunes library from your iPod or iOS device -
When migrating from time machine to my new hard drive, it migrates the first back-up I made several years ago. How can I migrate the latest back-up ? I need time machine to migrate the latest back-up. Should I delete the older back-ups ?
As noondaywitch says, it should use the latest backup.
Where are your backups (external HD, Time Capsule, etc.)?
It sounds like there are two separate sets, and you're not connected to the right set. -
Cant reinstall osx lion on new hard drive
I recently have been having problems with my 2007 Macbook 2,1 (yeah, I know it's old but it works...or worked anyway) taking forever to boot up. So, I backed up all of my data to an external drive, erased the drive and then attempted to reinstall osx lion (which was the current os on the machine prior to erasing) via the internet recovery option as I no longer have the original start up disc. The progress bar gets all the way to the end and then just takes me back to the main OSX utilities page. Tried reformatting the drive again and same thing. So then I resorted to creating a bootable thumb drive. I booted back into OSX utilities via this drive and tried to reinstall this way only to get an error message that it cant download additional files needed to install osx.
Next up, I used a borrowed mac, redownloaded the OSX installer from the app store and installed it on an external drive. I then booted my machine from the ext. drive into OSX lion, downloaded the installer again and attempted to install it on to my HD only to get an error message that the file may be corrupt or may have been tampered with. At this point, i went to the Apple store. The guy ran some checks but ultimately was also unable to reinstall the os. He even tried going back down to 10.6.8. So he told me this was a sign that the hard drive was bad and that they have no way of actually diagnosing it on a machine that old.
So, I went and bought a new WD 320G internal drive to replace the "bad" one in the machine. I then went through all of the steps above again and still have had no luck getting the os back on the machine. So at this point I am at a total loss. Is the computer just dead or is there anything else I could possibly try?Did you prep the new drive correctly? You also need to install Snow Leopard on the new drive and update it to 10.6.8.
Drive Partition and Format
1. Boot from your OS X Installer Disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu.
If you are preparing an external or a non-startup drive, then open Disk Utility in your Utilities folder.
2. After DU loads select your hard drive (this is the entry with the mfgr.'s ID and size) from the left side list. Note the SMART status of the drive in DU's status area. If it does not say "Verified" then the drive is failing or has failed and will need replacing. SMART info will not be reported on external drives. Otherwise, click on the Partition tab in the DU main window.
3. Under the Volume Scheme heading set the number of partitions from the drop down menu to one. Click on the Options button, set the partition scheme to GUID then click on the OK button. Set the format type to Mac OS Extended (Journaled.) Click on the Apply button and wait until the process has completed.
4. Select the volume you just created (this is the sub-entry under the drive entry) from the left side list. Click on the Erase tab in the DU main window.
5. Set the format type to Mac OS Extended (Journaled.) Click on the Security button, check the button for Zero Data and click on OK to return to the Erase window.
6. Click on the Erase button. The format process can take up to several hours depending upon the drive size.
In the following you can skip the part for partitioning and formatting if you've done the above already.
Clean Install of Snow Leopard
1. Boot the computer using the Snow Leopard Installer Disc or the Disc 1 that came
with your computer. Insert the disc into the optical drive and restart the computer.
After the chime press and hold down the "C" key. Release the key when you see
a small spinning gear appear below the dark gray Apple logo.
2. After the installer loads select your language and click on the Continue
button. When the menu bar appears select Disk Utility from the Utilities menu.
After DU loads select the hard drive entry from the left side list (mfgr.'s ID and drive
size.) Click on the Partition tab in the DU main window. Set the number of
partitions to one (1) from the Partitions drop down menu, click on Options button
and select GUID, click on OK, then set the format type to MacOS Extended
(Journaled, if supported), then click on the Apply button.
3. When the formatting has completed quit DU and return to the installer. Proceed
with the OS X installation and follow the directions included with the installer.
4. When the installation has completed your computer will Restart into the Setup
Assistant. Be sure you configure your initial admin account with the exact same
username and password that you used on your old drive. After you finish Setup
Assistant will complete the installation after which you will be running a fresh
install of OS X. You can now begin the update process by opening Software
Update and installing all recommended updates to bring your installation current.
Download and install Mac OS X 10.6.8 Update Combo v1.1. -
Can't instal Windows 7 to new hard drive
Hello everyone,
I was looking for solution for a while, but cant find it, so I really hope you'll help me here !
First of all, I 've been using my pc until I received the S.M.A.R.T. warning about possible hard drive failure soon, and one morning PC didnt start - one of the hard drives was dead (in my hp model there are two hard drives). After finding out which one was it ( I tried taking one hard drive out, leaving the other and vice versa) I bought a new 500 GB hard drive. Aparently the damaged hard drive was the one with operating system, because of startup message which told me that operating system not found. Nothing fancy, just instal windows like I always did, or so I thought ..
Got my USB flash drive with Windows 7 64 bit, plug it in, the usual windows instal guide loads up. I choose my language , keyboard input etc . At the point where I have to choose "where do I want to instal my windows" I see two hard drives: 1) disk 0 Partition 1 (my old original 232 GB stock drive) and 2) disk 1 Partition 1 (new recently purchased 500GB drive).
So ofcourse, since I replaced old hard drive with the new one I just bought, put it in the same slot, naturaly I chose my location for windows - new hard disk 1 Partition 1. When I highlighted it, a yellow mark apeared at the botom which said "Windows cannot be installed to this disk. This computer's hardware may not support booting to this disk. Ensure the disk's controller is enabled in the computer's BIOS menu".
Ok, so I tried to continue anyway, I pressed next and windows began to instal, took about 10 - 15 mins. Everythings normal until first restart part before completing instalation. PC restarted and .. Windows instalation setup started once more from the begining. So I thought , ok I ll try to instal to the old hard drive disk 0 Partition 1 ( this time there was no yellow warning mark). So instalation began again , restarted , and ... Once more instalation setup starting from begining !
I am really lost here, I tried replacing hard drives places whith each other, or leaving just one of them, every time windows starts instaling from begining ! Allthough, everytime there are less and less disk space, which means it actualy is instaling.
So any thoughts where to start ?
I would be so greatful for your help,
And see yaHi @Seniunas ,
Welcome to the HP Forums!
It is a terrific place to find answers and suggestions!
For you to have the best experience in the HP forum I would like to direct your attention to the HP Forums Guide Learn How to Post and More
It is my understand that one of your two hard drives failed. You have replaced the failed drive and are having a difficulty installing Windows 7 from a USB stick.
I have some questions.
What is your exact model of n DV9700 notebook?
How Do I Find My Model Number or Product Number?
Is this a retail version of Windows 7?
Were your drives setup in a RAID configuration or just two individual drives, one being the boot drive with Windows.
You could try this, I am not sure if it will work.
Remove the 232 GB drive completely from your system.
Boot to your Windows 7, USB stick and let Windows format the drive before it installing Windows.
If this completes successfully, make sure the boot order is set to boot to that drive and test it.
If you are then able to boot into windows, shut down the notebook and reinstall the secondary drive.
Good Luck!
Sparkles1
I work on behalf of HP
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the bottom right to say “Thanks” for helping! -
Windows 7 Enterprise is not genuine after installing new hard-drive and cloning the old one
I retired from my job as a university professor two years ago, and they let me keep my laptop computer, which is a Dell Latitude E4300 with Windows 7 Enterprise installed. I do not have any of the original disks for Windows. Recently, the hard-drive began
to fail, so I replaced it with a new one, cloning the old hard-drive onto the new one. Soon after that, a popup window began appearing saying that this computer is not running genuine windows. One important consequence of this is that I can no longer use Windows
Update, so I have concerns about security. If I go to the control panel under “System”, it says windows is activated and gives me the Product ID. I have talked to tech support at Microsoft, and they tell me something along the lines of the following: that
the problem is the new hard-drive is not recognized as being licensed to use this copy of Windows, and that I should post a question on one of the forums asking this: How can I reinstall Windows 7 Enterprise on the new hard-drive? Any assistance will be much
appreciated.
PS I have no idea which forum this should go under, so pretty much just picked one randomly.Thank you for the reply. Below is the diagnostic report:
Diagnostic Report (1.9.0027.0):
Windows Validation Data-->
Validation Code: 0x8004FE21
Cached Online Validation Code: 0x0
Windows Product Key: *****-*****-*****-*****-XVH7B
Windows Product Key Hash: juq6zzHf9lIH1XRY1VK2YrQYWO0=
Windows Product ID: 55041-011-1350732-86681
Windows Product ID Type: 6
Windows License Type: Volume MAK
Windows OS version: 6.1.7601.2.00010100.1.0.004
ID: {04DEBE17-699E-4D0A-A59D-3C196C2C84FE}(3)
Is Admin: Yes
TestCab: 0x0
LegitcheckControl ActiveX: N/A, hr = 0x80070002
Signed By: N/A, hr = 0x80070002
Product Name: Windows 7 Enterprise
Architecture: 0x00000009
Build lab: 7601.win7sp1_gdr.130828-1532
TTS Error:
Validation Diagnostic:
Resolution Status: N/A
Vista WgaER Data-->
ThreatID(s): N/A, hr = 0x80070002
Version: N/A, hr = 0x80070002
Windows XP Notifications Data-->
Cached Result: N/A, hr = 0x80070002
File Exists: No
Version: N/A, hr = 0x80070002
WgaTray.exe Signed By: N/A, hr = 0x80070002
WgaLogon.dll Signed By: N/A, hr = 0x80070002
OGA Notifications Data-->
Cached Result: N/A, hr = 0x80070002
Version: N/A, hr = 0x80070002
OGAExec.exe Signed By: N/A, hr = 0x80070002
OGAAddin.dll Signed By: N/A, hr = 0x80070002
OGA Data-->
Office Status: 100 Genuine
Microsoft Office Enterprise 2007 - 100 Genuine
OGA Version: N/A, 0x80070002
Signed By: N/A, hr = 0x80070002
Office Diagnostics: 025D1FF3-364-80041010_025D1FF3-229-80041010_025D1FF3-230-1_025D1FF3-517-80040154_025D1FF3-237-80040154_025D1FF3-238-2_025D1FF3-244-80070002_025D1FF3-258-3_E2AD56EA-765-d003_E2AD56EA-766-0_E2AD56EA-134-80004005_E2AD56EA-765-b01a_E2AD56EA-766-0_E2AD56EA-148-80004005_16E0B333-89-80004005_B4D0AA8B-1029-80004005
Browser Data-->
Proxy settings: N/A
User Agent: Mozilla/4.0 (compatible; MSIE 8.0; Win32)
Default Browser: C:\Program Files (x86)\Mozilla Firefox\firefox.exe
Download signed ActiveX controls: Prompt
Download unsigned ActiveX controls: Disabled
Run ActiveX controls and plug-ins: Allowed
Initialize and script ActiveX controls not marked as safe: Disabled
Allow scripting of Internet Explorer Webbrowser control: Disabled
Active scripting: Allowed
Script ActiveX controls marked as safe for scripting: Allowed
File Scan Data-->
File Mismatch: C:\Windows\system32\wat\watadminsvc.exe[7.1.7600.16395], Hr = 0x80092003
File Mismatch: C:\Windows\system32\wat\watux.exe[7.1.7600.16395], Hr = 0x80092003
File Mismatch: C:\Windows\system32\sppobjs.dll[6.1.7601.17514], Hr = 0x80092003
File Mismatch: C:\Windows\system32\sppc.dll[6.1.7601.17514], Hr = 0x800b0100
File Mismatch: C:\Windows\system32\sppcext.dll[6.1.7600.16385], Hr = 0x800b0100
File Mismatch: C:\Windows\system32\sppwinob.dll[6.1.7601.17514], Hr = 0x80092003
File Mismatch: C:\Windows\system32\slc.dll[6.1.7600.16385], Hr = 0x800b0100
File Mismatch: C:\Windows\system32\slcext.dll[6.1.7600.16385], Hr = 0x800b0100
File Mismatch: C:\Windows\system32\sppuinotify.dll[6.1.7600.16385], Hr = 0x80092003
File Mismatch: C:\Windows\system32\slui.exe[6.1.7601.17514], Hr = 0x80092003
File Mismatch: C:\Windows\system32\sppcomapi.dll[6.1.7601.17514], Hr = 0x800b0100
File Mismatch: C:\Windows\system32\sppcommdlg.dll[6.1.7600.16385], Hr = 0x800b0100
File Mismatch: C:\Windows\system32\sppsvc.exe[6.1.7601.17514], Hr = 0x80092003
File Mismatch: C:\Windows\system32\drivers\spsys.sys[6.1.7127.0], Hr = 0x80092003
File Mismatch: C:\Windows\system32\drivers\spldr.sys[6.1.7127.0], Hr = 0x80092003
File Mismatch: C:\Windows\system32\systemcpl.dll[6.1.7601.17514], Hr = 0x800b0100
File Mismatch: C:\Windows\system32\user32.dll[6.1.7601.17514], Hr = 0x800b0100
Other data-->
Office Details: <GenuineResults><MachineData><UGUID>{04DEBE17-699E-4D0A-A59D-3C196C2C84FE}</UGUID><Version>1.9.0027.0</Version><OS>6.1.7601.2.00010100.1.0.004</OS><Architecture>x64</Architecture><PKey>*****-*****-*****-*****-BBBBB</PKey><PID>55041-011-1350732-86681</PID><PIDType>6</PIDType><SID>S-1-5-21-240060965-2561850352-3419627931</SID><SYSTEM><Manufacturer>Dell
Inc.</Manufacturer><Model>Latitude E4300 </Model></SYSTEM><BIOS><Manufacturer>Dell Inc.</Manufacturer><Version>A21</Version><SMBIOSVersion
major="2" minor="4"/><Date>20110111000000.000000+000</Date></BIOS><HWID>68B63A07018400F8</HWID><UserLCID>0409</UserLCID><SystemLCID>0409</SystemLCID><TimeZone>Pacific Standard Time(GMT-08:00)</TimeZone><iJoin>1</iJoin><SBID><stat>3</stat><msppid></msppid><name></name><model></model></SBID><OEM><OEMID>DELL
</OEMID><OEMTableID>M09 </OEMTableID></OEM><GANotification/></MachineData><Software><Office><Result>100</Result><Products><Product GUID="{90120000-0030-0000-0000-0000000FF1CE}"><LegitResult>100</LegitResult><Name>Microsoft
Office Enterprise 2007</Name><Ver>12</Ver><Val>1DB36DFCEA6586</Val><Hash>uf4pjarnSPRhy0+iMrKzL8KTLeY=</Hash><Pid>89388-707-1262377-65112</Pid><PidType>14</PidType></Product></Products><Applications><App
Id="15" Version="12" Result="100"/><App Id="16" Version="12" Result="100"/><App Id="18" Version="12" Result="100"/><App Id="19" Version="12" Result="100"/><App Id="1A" Version="12" Result="100"/><App Id="1B" Version="12" Result="100"/><App
Id="44" Version="12" Result="100"/><App Id="A1" Version="12" Result="100"/><App Id="BA" Version="12" Result="100"/></Applications></Office></Software></GenuineResults>
Spsys.log Content: 0x80070002
Licensing Data-->
Software licensing service version: 6.1.7601.17514
Name: Windows(R) 7, Enterprise edition
Description: Windows Operating System - Windows(R) 7, VOLUME_MAK channel
Activation ID: 9abf5984-9c16-46f2-ad1e-7fe15931a8dd
Application ID: 55c92734-d682-4d71-983e-d6ec3f16059f
Extended PID: 55041-00172-011-135073-03-1033-7600.0000-0402011
Installation ID: 017002020180881956515246274583104396790522223804443953
Processor Certificate URL: http://go.microsoft.com/fwlink/?LinkID=88338
Machine Certificate URL: http://go.microsoft.com/fwlink/?LinkID=88339
Use License URL: http://go.microsoft.com/fwlink/?LinkID=88341
Product Key Certificate URL: http://go.microsoft.com/fwlink/?LinkID=88340
Partial Product Key: XVH7B
License Status: Licensed
Remaining Windows rearm count: 3
Trusted time: 6/6/2014 2:38:03 PM
Windows Activation Technologies-->
HrOffline: 0x8004FE21
HrOnline: N/A
HealthStatus: 0x000000000001EFF0
Event Time Stamp: 5:30:2014 15:10
ActiveX: Registered, Version: 7.1.7600.16395
Admin Service: Registered, Version: 7.1.7600.16395
HealthStatus Bitmask Output:
Tampered File: %systemroot%\system32\sppobjs.dll
Tampered File: %systemroot%\system32\sppc.dll|sppc.dll.mui
Tampered File: %systemroot%\system32\sppcext.dll|sppcext.dll.mui
Tampered File: %systemroot%\system32\sppwinob.dll
Tampered File: %systemroot%\system32\slc.dll|slc.dll.mui
Tampered File: %systemroot%\system32\slcext.dll|slcext.dll.mui
Tampered File: %systemroot%\system32\sppuinotify.dll|sppuinotify.dll.mui
Tampered File: %systemroot%\system32\slui.exe|slui.exe.mui|COM Registration
Tampered File: %systemroot%\system32\sppcomapi.dll|sppcomapi.dll.mui
Tampered File: %systemroot%\system32\sppcommdlg.dll|sppcommdlg.dll.mui
Tampered File: %systemroot%\system32\sppsvc.exe|sppsvc.exe.mui
Tampered File: %systemroot%\system32\drivers\spsys.sys
HWID Data-->
HWID Hash Current: MgAAAAEAAQABAAIAAQABAAAAAwABAAEAeqgiDXhybAimeiQ1hEDag8ysrmAi+8rbRso=
OEM Activation 1.0 Data-->
N/A
OEM Activation 2.0 Data-->
BIOS valid for OA 2.0: yes
Windows marker version: 0x20001
OEMID and OEMTableID Consistent: yes
BIOS Information:
ACPI Table Name OEMID Value OEMTableID Value
APIC DELL M09
FACP DELL M09
HPET DELL M09
BOOT DELL M09
MCFG DELL M09
____ DELL M09
ASF! DELL M09
TCPA
SLIC DELL M09
SSDT PmRef CpuPm
scott cohen -
Pavilion 7 Bad Hard Drive, How to reinstall HP software on new Hard Drive?
Hi, I have a 2 1/2 year old p7 1247cb running Windows 8 Pro x64, just out of warranty, and the Hitachi internal hard drive is failing (eightforums.com helped me with diagnostic tools). I am replacing the HD and want to reinstall the whole system that was on the machine when I bought it. It came with Windows 7 and a promotion for free upgrade to Windows 8, which I did. I have my Windows 8 Key Code and have borrowed the installation files for Windows 8.
This is the first time I've done this sort of replacment, and I am wondering whether it's possible, or even desirable, to get all the manufacturer-installed drivers and software back on the new HD, or should I just let the Windows install search for all drivers for me?
Until the HD started failing, this was by far the most reliable desktop setup I've ever used, and I am wary about whether the new system, with cobbled-together drivers, will be as stable and reliable as what I had with the manufacturer-installed software and drivers,
Plus, as an aside, I want to vent for a moment that it seems crazy to me that a hard drive should start failing after just 2.5 years! This bundle was sold as a gaming system (it's never used for gaming, but the specs were what I wanted), and while it gets heavy use (mostly streaming video, wordprocessing, photo/video -editing and storage), I was surprised to encounter a hardware issue only 6 months past the warranty.
Any assistance is appreciated.Hi,
Hard drives are mechanical and do fail. It's quite common in the industry and not just with HP.
Be sure that the new hard drive is not an advanced format hard drive and is not greater than 2TB.
Back up your data to external media if you can. If not then you will need to later use for backups.
Be sure to create the external HP recovery media (this should have already been done right after you received your PC).If you don't have the external recovery media then order it from HP. HP Recovery Disks. Performing a HP System Recovery with Windows 7
Replace the hard drive and then boot up the external HP recovery media and recovery your PC back to a factory day one condition.
Now you can reinstall Windows 8 using your "borrowed Windows 8 media".
There may be other ways of installing Windows 8 but I have given you the text book method. A generic key method, mentioned by me on this forum long ago and just recently revisted by another forum member may work.
HP DV9700, t9300, Nvidia 8600, 4GB, Crucial C300 128GB SSD
HP Photosmart Premium C309G, HP Photosmart 6520
HP Touchpad, HP Chromebook 11
Custom i7-4770k,Z-87, 8GB, Vertex 3 SSD, Samsung EVO SSD, Corsair HX650,GTX 760
Custom i7-4790k,Z-97, 16GB, Vertex 3 SSD, Plextor M.2 SSD, Samsung EVO SSD, Corsair HX650, GTX 660TI
Windows 7/8 UEFI/Legacy mode, MBR/GPT -
Please help! Cannot access TC backups on new hard drive with Lion!
I know this seems like a generic posting, and believe me that I have searched through countless posts to find the situation most similar to mine. To start, the basic story (I am pretty computer illiterate, so excuse the lack of terminology):
-My computer was working slow, beach balling, etc. two weeks ago - took to Apple Genius Bar for help and they suggested need for new hard drive. I already had a hard drive crash in January, but since I have had a Time Capsule running Time Machine since September 2009, I hooked it right up and restored from a backup with no issue... so I wasn't worried about this. I waited to make sure that I had the most recent backup (and needed to use my computer for law school for a couple days), so I turned it in a day later immediately after a complete incremental backup via TM on my TC.
-Got my computer back from the Apple "depot" with new hard drive and hard drive cable.
-Had an extremely hard time getting my TC to link to my computer and via AppleCare phone help, realized that Apple had given me back my computer with Leopard, and they said that I needed to go back to the store to get a Lion reinstall since the backups had been done in Lion.
-Went back to Apple store, reinstalled Lion... they told me there would be no issue once I got home and hooked up to TC. Connected to TC via ethernet and went through "set up" procedure as if it was new computer - could never get past the "Select the Disk" page. Either it was beach-balling or just sitting there, and I couldn't click continue or anything.
-Called AppleCare again, they said to try it through Migration Assistant instead of Set Up... again, could not connect to TC. They said it was too complicated to do over the phone and sent me back to the store...
-By now, I am on vacation and spent 5, yes FIVE, hours at another store trying to migrate the data to no avail. I obviously don't know everything they tried, but I know they tried installing each operating system since Leopard, going through set up and migration assistant, and doing a disk repair of the TC. None of this worked. Every single time my TC connects and you can see the title of the drive ("Data") and the two separate backups ("emilysmac" was my old computer and "emilysmacbookpro" was the dummy one we tried to make). Emilysmacbookpro was accessible with no data on it, but once we clicked on emilysmac it just said "connecting" forever and never did anything.
Basically:
-300GB of my TC shows that it has been used, so I know something is there.
-I can also pull up the data on another computer, and it shows files dated from September 2009 up to the date I last updated, but they do not look how they used to - they are "Unix Executable" files and cannot open through Time Machine.
I have a really hard time thinking that my TC AND my computer hard drive failed at the same time - which is actually what Apple suggested to me. Is there anything that anyone knows that will help?! I am desperate here! This TC had backups of all my music, pictures and law school work over the past 2.5 years. Any help would be much appreciated!PS I have also looked through Pondini's site, but I am not sure if I am missing something since I don't totally understand all of it. Thanks again!
-
I can't install Snow Leopard on a brand new hard drive with a brand new optical drive.
I need help please. I have a 2009 MacBook Pro. The hard drive crashed a while back so I bought a new one. The original Snow Leopard disc that came with it was scratched so I bought a new one of it as well. After trying/failing to install Snow Leopard on the new hard drive about a dozen times I bought a new optical drive as well. I installed the new optical drive today, tried to install Snow Leopard again and STILL got the same installation error messages. Any help that anyone might be able to provide would be greatly appreciated.
Last error message:
Install failed: The Installer could not copy the necessary support files.Did you partition and format the new drive first?
Drive Partition and Format
1. Boot from your OS X Installer Disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu.
2. After DU loads select your hard drive (this is the entry with the mfgr.'s ID and size) from the left side list. Note the SMART status of the drive in DU's status area. If it does not say "Verified" then the drive is failing or has failed and will need replacing. SMART info will not be reported on external drives. Otherwise, click on the Partition tab in the DU main window.
3. Under the Volume Scheme heading set the number of partitions from the drop down menu to one. Click on the Options button, set the partition scheme to GUID then click on the OK button. Set the format type to Mac OS Extended (Journaled.) Click on the Apply button and wait until the process has completed.
4. Select the volume you just created (this is the sub-entry under the drive entry) from the left side list. Click on the Erase tab in the DU main window.
5. Set the format type to Mac OS Extended (Journaled.) Click on the Security button, check the button for Zero Data and click on OK to return to the Erase window.
6. Click on the Erase button. The format process can take up to several hours depending upon the drive size.
7. Upon completion quit Disk Utility and return to the installer. Complete the Snow Leopard installation.
Maybe you are looking for
-
After I upgraded tothe IOS 6 operating system on my iphone 3GS I lost several of my apps. They don't show up anymore. I tried to reinstall them again using itunes, but they just show an "open" tab instead of an "install" tab. When I click open, it br
-
Deleting a row from a Table Region
Hi Everyone, Before I start I must say that I am fairly new to OA Framework. I thought this should be straight forward but it does not seem to be. Or I simplt dont know about it. I have a simple Query Region and a table (based on a VO). This VO is at
-
Problems with gradient tool bar not remaining on object applied in illustrator cc
Hello, when applying a gradient to a rectangle i will get the gradient tool, click on the left half of the object i want it applied to and while holding down drag a line to thew right hand side of the object. the problem the arises when i release the
-
I am trying to log on to sqlplus of ebusiness through putty and i am not getting an headway, basically i surely don't know my way rounfd the files system yet. But this is what i have done [olu@nith ~]$ cd / [olu@nith /]$ ls BACS dev foglight initrd m
-
How to load software to mac mini
how to load new software to mac mini?