Rejected mail message: "Remote host said: 550 5.1....

My email to a relation who has an address on icloud email (e.g. [email protected]) was rejected with the following message:
"Remote host said: 550 5.1.1 unknown or illegal alias:"
Is there anything I can do from my end; i.e. on btinternet.com webmail?
Thanks in advance.
Solved!
Go to Solution.

What has happened to BTYahoo??? I have used BTInternet for years, the last 4 in South Africa. A couple of times I have had to change SMTP but this time...... All of a sudden it's BT Com and I can't send emails. I pay for this service monthly to keep my BT Internet address but I may as well notify everyone of my GMail address and change all of my BT Internet sign ins!!!

Similar Messages

Remote host said: 550 5.2.1 Mail from 209.X.X.X refused: spa

Dear All,
My Friend is facing a problem he is not able to send mails from outside for e.g yahoo.com his mx is natted on the firewall to my exchange server.
Sender gets a bounce back mail stating below: -
<XXX>:
203.X.X.X does not like recipient.
Remote host said: 550 5.2.1 Mail from 209.X.X.X refused: spam site.
Giving up on 203.X.X.X.
Sorry but i dont know whether this forum should answer my querries which are actually of my friends.
But if you could it would be really helpful.
Thanks in advance.
Regards,
Ranjit

Hi Ranjit,
203.X.X.X does not like recipient.
Remote host said: 550 5.2.1 Mail from 209.X.X.X refused: spam site.
Giving up on 203.X.X.X.
implies that the recipient server is using antispam or blacklist software to refuse connections from certain IP addresses, including the 209.x.x.x address you cited.
I would consider using an RBL lookup tool such as
http://www.mxtoolbox.com/blacklists.aspx to check the 209.x.x.x address against different RBLs.
If it turns out that it is indeed listed, you would need to go to the respective listing site to see how to get off their list.
( I am not affiliated with mxtoolbox, they just have a convenient lookup tool on their site )

How to send the mail to remote host

I'm using sendmail as my default SMTP service, but when I was sending the mail to remote host, I got error from /var/log/syslog:
Feb 22 15:44:24 hostname sendmail[897]: [ID 801593 mail.info] g1M7fW800840: to=<[email protected]>, ctladdr=<user@hostname> (0/1), delay=00:02:18, xdelay=00:00:00, mailer=esmtp, pri=300344, relay=relay.us.mailserver.net. [200.100.100.1], dsn=4.0.0, stat=Deferred: Cannot assign requested address
How can I solve this problem?

Hi,
please enter the tcode SBWP click on new message then enter the subject and description.
enter email id and select type as internet address or external address then click on send button.
Regards,
Arti

Rejected mail messages

Hallo
Recently I installed Sun Communication Suite with Messaging server included. I migrated to some test users to new installation and they report, that there are mail messages frequently rejected with explanation:
Thu, 20 May 2010 19:50:21 +0200 (CEST)
Temporary error from SMTP partner: smtp;451 See [http://pobox.com/~djb/docs/smtplf.html]
Error occured to webmail users and users with other mail clients. I searched for answer, but I still don't have I clue, how to change my mailer to avoid this.
Regards
Matej

Output from imsimta version is:
Sun Java(tm) System Messaging Server 7u2-7.02 64bit (built Apr 16 2009)
libimta.so 7u2-7.02 64bit (built 03:03:02, Apr 16 2009)
Using /opt/sun/comms/messaging64/config/imta.cnf (compiled)
SunOS mailstore 5.10 Generic_138888-01 sun4v sparc SUNW,SPARC-Enterprise-T5120
You are right. Delivery notice come later. Here is example of whole message.
Message-id: <[email protected]>
Date: Tue, 18 May 2010 18:50:18 0200+
From: =?iso-8859-15?Q?=22Petja_Plau=A8tajner=22?=
+<[email protected]>+
To: Ana Filipov <[email protected]>
Subject: Re: dunaj
Your message has been enqueued and undeliverable for 2 days to the following recipients:
Recipient address: [email protected]
Reason: unable to deliver this message after 2 days
Delivery attempt history for your mail:
Thu, 20 May 2010 19:50:21 0200 (CEST)+
Temporary error from SMTP partner: smtp;451 See http://pobox.com/~djb/docs/smtplf.html.
Thu, 20 May 2010 11:50:20 0200 (CEST)+
Temporary error from SMTP partner: smtp;451 See http://pobox.com/~djb/docs/smtplf.html.
Thu, 20 May 2010 03:50:20 0200 (CEST)+
Temporary error from SMTP partner: smtp;451 See http://pobox.com/~djb/docs/smtplf.html.
Wed, 19 May 2010 19:50:20 0200 (CEST)+
Temporary error from SMTP partner: smtp;451 See http://pobox.com/~djb/docs/smtplf.html.
Wed, 19 May 2010 11:50:19 0200 (CEST)+
Temporary error from SMTP partner: smtp;451 See http://pobox.com/~djb/docs/smtplf.html.
Wed, 19 May 2010 07:50:19 0200 (CEST)+
Temporary error from SMTP partner: smtp;451 See http://pobox.com/~djb/docs/smtplf.html.
Wed, 19 May 2010 03:50:19 0200 (CEST)+
Temporary error from SMTP partner: smtp;451 See http://pobox.com/~djb/docs/smtplf.html.
Tue, 18 May 2010 23:50:19 0200 (CEST)+
Temporary error from SMTP partner: smtp;451 See http://pobox.com/~djb/docs/smtplf.html.
Tue, 18 May 2010 21:50:19 0200 (CEST)+
Temporary error from SMTP partner: smtp;451 See http://pobox.com/~djb/docs/smtplf.html.
Tue, 18 May 2010 19:50:19 0200 (CEST)+
Temporary error from SMTP partner: smtp;451 See http://pobox.com/~djb/docs/smtplf.html.
Tue, 18 May 2010 18:50:19 0200 (CEST)+
Temporary error from SMTP partner: smtp;451 See http://pobox.com/~djb/docs/smtplf.html.
The mail system will continue to try to deliver your message for an additional 5 days.
I don't see any additional information in whole message.
Regards
Matej

When sending e-mail messages to a mail-enabled public folder that have been replicated from old Exchange Server 2000/2003/2007, Exchange Server 2010 environment mails are rejected with NDR.

Hi, I would like to share with you issue that I’ve solved regarding mail-enabled PF that migrated from Exchange 2000/2003/2007 to 2010, I’ve searched & contacted my MVP leader – there’s no official KB regarding this issue right
now, so I’m posting here in order to share this among others.
Note: There’s article(s) that talked about PF replication from Exch2000/2003/2007 to 2010 – this is the same issue as well.
Symptoms
E-mail messages that been sent to mail-enabled public folder in Exchange Server 2010 environment rejected with the following NDR:
“#< #5.2.0 smtp;554 5.2.0 STOREDRV.Deliver.Exception:ObjectNotFoundException; Failed to process message due to a permanent exception with message The Active Directory user wasn’t found. ObjectNotFoundException: The Active Directory
user wasn’t found.> #SMTP#”
Sometimes Exchange Server 2010 is documented as well Event ID 1020 on the Event Viewer with this information:
“Log Name: Application
Source: MSExchange Store Driver
Event ID: 1020
Level: Error
Description:
The store driver couldn’t deliver the public folder replication message "Hierarchy ([email protected])" because the following error occurred: The Active Directory user wasn't found.”
Cause
In an environment where Microsoft Exchange Server 2000 or Microsoft Exchange Server 2003 previously existed, and all those servers have been removed, there is a chance that an Administrative Group (First Administrative Group or another custom Administrative
Group) remains with a Servers container, but no servers inside it.
During replication, when the Exchange 2010 Store Driver sees the empty Servers container in Active Directory, it's expecting a System Attendant object inside the container and when it is not found the error occurs.
Resolution
To work around the issue, delete the empty Servers container. This can't be done through Exchange System Manager. Use the ADSI Edit tool to remove it using the following steps:
Warning If you use the ADSI Edit snap-in, the LDP utility, or any other LDAP version 3 client, and you incorrectly modify the attributes of Active Directory objects, you can cause serious problems. These problems may require you to reinstall Microsoft Windows
2003 Server, Microsoft Windows Server 2008, Microsoft Exchange 2010 Server or both Windows and Exchange. Microsoft cannot guarantee that problems that occur if you incorrectly modify Active Directory object attributes can be solved. Modify these attributes
at your own risk.
1.
Start the ADSI Edit MMC Snap-in. Click Start, then
Run, and type adsiedit.msc, and then click OK.
2.
Connect & Expand the Configuration Container [YourServer.DNSDomainName.com], and then expand
CN=Configuration,DC=DNSDomainName,DC=com.
3.
Expand CN=Services, and then CN=Microsoft Exchange, and then expand
CN=YourOrganizationName.
4.
You will see an empty Administrative Group. Expand the
CN=YourAdministrativeGroupName.
5.
Expand CN=Servers.
6.
Verify there are no server objects listed under the
CN=Servers container.
7.
Right click on the empty CN=Servers container and choose
Delete.
8.
Verify the modification, and try to send again the E-mail to the mail-enabled public folder.
Applies to
Exchange Server 2010, Standard Edition
Exchange Server 2010, Enterprise Edition
Netanel Ben-Shushan, MCSA/E, MCTS, MCITP, Windows Expert-IT Pro MVP. IT Consultant & Trainer | Website (Hebrew): http://www.ben-shushan.net | IT Services: http://www.ben-shushan.net/services | Weblog (Hebrew): http://blogs.microsoft.co.il/blogs/netanelb
| E-mail: [email protected]

Sounds like you are looking in the wrong Administrative Group container which is why you are seeing your Exchange 2010 servers in there.
When you install Exchange 2003 only you will see a container named by default as "CN=First Administrative Group" container. But this could be named anything if you changed the Organization Name on the installation when you installed the first
Exchange 2003 server into the domain/forest.
You will notice that when you install Exchange 2010 part of the AD setup is to create a new configuration container and is named by default "CN=First Administrative Group (FYDIBOHF23SPDLT)".
So it sounds like you are not looking in the right location within ADSIEdit.
You may find the following article also helpful for this issue which is the same resolution:
http://blogs.technet.com/b/sbs/archive/2012/05/17/empty-cn-servers-container-causing-issues-with-public-folders-on-small-business-server-2011.aspx
I recommend though that you ensure your Exchange 2003 servers are fully uninstalled or no longer present in your environment before you go deleting the Servers container though.. The following Microsoft article will help with this:
http://technet.microsoft.com/en-gb/library/gg576862(v=exchg.141).aspx

I tried to send a mail message to too many addees. when the rejection came back "cannot send message using the server..." the window is too long to be able to see the choices at the bottom of it. how can i see the choices at the bottom of that window?

I tried to send a mail message to too many addees. when the rejection came back "cannot send message using the server..." the window is too long to be able to see the choices at the bottom of it. how can I see the choices at the bottom of that window?

I tried to send it through gmail and the acct is a POP acct
I'm not concerned about sending to the long address list. I just can't get the email and window that says "cannot send emai using the server..." to go away. The default must be "retry", because although I cannot see the choices at the bottom of the window if I hit return it trys again... and then of course comes back with the very long pop up window that I cannot see the bottom of so I can tell it to quit trying...

Inserting Remote Image In Mail Message?

Hi,
Is it possible to link to a Remote Image in an Apple Mail Message and have it load within the e-mail? What I mean is, can you link to a photo on a site like Flickr, and have the image display within the e-mail, rather than just the text link?

this is possible but you have to jump through hoops to do it which personally strikes me as completely ridiculous.
the only way I know how to achieve this is the following.
make an html document using your favorite html editor and insert a remote pic in it.
then open this file in safari and enter command+i. this page will be opened in a new outgoing mail message and you can mail it.
I would be delighted to know if there is an easier way to do this.

I recently installed CS4, and I can not make a connection to my website. Message an FTP error occurred and cannot make a connection to host. The remote host cannot be found.

I recently installed CS4, and I can not make a connection to my website. Message an FTP error occurred and cannot make a connection to host. The remote host cannot be found.

Open up your site definition (double-click on the site name in the File panel or choose Site > Manage Sites > Edit) and go to the Remote Info category. There, click Use Firewall (if it isn't already selected) - press Test to try the default firewall settings. If that doesn't work, click Firewall Settings. You'll see two relevant settings about 2/3 down - Firewall host and Firewall port. If Firewall port is 21, there probably is something blocking the port.
On Windows XP, you may have the Windows Firewall installed and blocking. Here's how you get to it:
To open Windows Firewall
1.
Click Start and then click Control Panel.
2.
In the control panel, click Windows Security Center.
3.
Click Windows Firewall.
Once you have that open, you'll need to set Dreamweaver as an exception to blocking:
On the Exceptions tab, click Add Program.
In the list of programs, click the name of the program (Dreamweaver) that you want to add, and then click OK. If the name of your program is not in the list of programs, click Browse to locate the Dreamweaver.exe in the Program Files folder and then click OK.
Hope this helps - Joe
Joseph Lowery
Author, Dreamweaver CS4 Bible

Error message ftp-connection to remote host

hi guys,
i have problems with a ftp-connection between a business-service (alsb) and a remote-host.( we used alsb 2.6 rp1)
i pick-up a file per ftp-proxy-service on a remote host. this is possible without problems. then i convert this file and i want to rewrite this file with a ftp-business-service back to the remotehost. but i get this error-message
<con:errorCode>BEA-380000</con:errorCode>
<con:reason>
General runtime error: Received error response (502) from FTP server [scylla.ce.ced] IP [10.1.224.7] port [21] status [connected] upon executing command [port 192,168,122,254,12,86]
who can help me??
regards thomas

Open up your site definition (double-click on the site name in the File panel or choose Site > Manage Sites > Edit) and go to the Remote Info category. There, click Use Firewall (if it isn't already selected) - press Test to try the default firewall settings. If that doesn't work, click Firewall Settings. You'll see two relevant settings about 2/3 down - Firewall host and Firewall port. If Firewall port is 21, there probably is something blocking the port.
On Windows XP, you may have the Windows Firewall installed and blocking. Here's how you get to it:
To open Windows Firewall
1.
Click Start and then click Control Panel.
2.
In the control panel, click Windows Security Center.
3.
Click Windows Firewall.
Once you have that open, you'll need to set Dreamweaver as an exception to blocking:
On the Exceptions tab, click Add Program.
In the list of programs, click the name of the program (Dreamweaver) that you want to add, and then click OK. If the name of your program is not in the list of programs, click Browse to locate the Dreamweaver.exe in the Program Files folder and then click OK.
Hope this helps - Joe
Joseph Lowery
Author, Dreamweaver CS4 Bible

Auth.log - Rejected send message, 2 matched rules; type="method_call"

Hi,
i'm checking the /var/log/auth.log and I found out that there is this error message
Jun 9 20:19:56 localhost polkitd(authority=local): Registered Authentication Agent for unix-session:/org/freedesktop/ConsoleKit/Session2 (system bus name :1.23 [/usr/bin/gnome-shell], object path /org/freedesktop/PolicyKit1/AuthenticationAgent, locale en_US.UTF-8)
Jun 9 20:19:57 localhost dbus[513]: [system] Rejected send message, 2 matched rules; type="method_call", sender=":1.23" (uid=1000 pid=861 comm="/usr/bin/gnome-shell ") interface="org.freedesktop.DBus.Properties" member="GetAll" error name="(unset)" requested_reply="0" destination=":1.1" (uid=0 pid=654 comm="/usr/sbin/console-kit-daemon --no-daemon ")
Jun 9 20:19:57 localhost dbus[513]: [system] Rejected send message, 2 matched rules; type="method_call", sender=":1.23" (uid=1000 pid=861 comm="/usr/bin/gnome-shell ") interface="org.freedesktop.DBus.Properties" member="GetAll" error name="(unset)" requested_reply="0" destination=":1.1" (uid=0 pid=654 comm="/usr/sbin/console-kit-daemon --no-daemon ")
Jun 9 20:19:57 localhost dbus[513]: [system] Rejected send message, 2 matched rules; type="method_call", sender=":1.23" (uid=1000 pid=861 comm="/usr/bin/gnome-shell ") interface="org.freedesktop.DBus.Properties" member="GetAll" error name="(unset)" requested_reply="0" destination=":1.1" (uid=0 pid=654 comm="/usr/sbin/console-kit-daemon --no-daemon ")
if think the problem is in /etc/dbus-1/system.conf
<deny send_type="method_call"/>
I'm tempted to change this to allow, but I won't as long as I don't understand why this deny-rule is implemented.
Last edited by miky76 (2012-06-09 20:41:06)

That deny rule is the default. Things in /etc/dbus-1/system.d override it. There's a ConsoleKit.conf file in there that describes what interaction ConsoleKit actually allows.
That said, ConsoleKit.conf also denies this access:
<deny send_destination="org.freedesktop.ConsoleKit"
send_interface="org.freedesktop.DBus.Properties" />
I don't know why this is denied - most likely it's to prevent private data from being stolen from console-kit-daemon in this way. I don't see any such private data stored in properties on ConsoleKit, though:
$ dbus-send --print-reply --system --dest=org.freedesktop.ConsoleKit /org/freedesktop/ConsoleKit/Session1 org.freedesktop.DBus.Introspectable.Introspect
method return sender=:1.5 -> dest=:1.14 reply_serial=2
string "<!DOCTYPE node PUBLIC "-//freedesktop//DTD D-BUS Object Introspection 1.0//EN"
"http://www.freedesktop.org/standards/dbus/1.0/introspect.dtd">
<node>
<interface name="org.freedesktop.DBus.Introspectable">
<method name="Introspect">
<arg name="data" direction="out" type="s"/>
</method>
</interface>
<interface name="org.freedesktop.DBus.Properties">
<method name="Get">
<arg name="interface" direction="in" type="s"/>
<arg name="propname" direction="in" type="s"/>
<arg name="value" direction="out" type="v"/>
</method>
<method name="Set">
<arg name="interface" direction="in" type="s"/>
<arg name="propname" direction="in" type="s"/>
<arg name="value" direction="in" type="v"/>
</method>
<method name="GetAll">
<arg name="interface" direction="in" type="s"/>
<arg name="props" direction="out" type="a{sv}"/>
</method>
</interface>
<interface name="org.freedesktop.ConsoleKit.Session">
<method name="SetIdleHint">
<arg name="idle_hint" type="b" direction="in"/>
</method>
<method name="GetIdleSinceHint">
<arg name="iso8601_datetime" type="s" direction="out"/>
</method>
<method name="GetIdleHint">
<arg name="idle_hint" type="b" direction="out"/>
</method>
<method name="Unlock">
</method>
<method name="Lock">
</method>
<method name="Activate">
</method>
<method name="GetCreationTime">
<arg name="iso8601_datetime" type="s" direction="out"/>
</method>
<method name="IsLocal">
<arg name="local" type="b" direction="out"/>
</method>
<method name="IsActive">
<arg name="active" type="b" direction="out"/>
</method>
<method name="GetLoginSessionId">
<arg name="login_session_id" type="s" direction="out"/>
</method>
<method name="GetRemoteHostName">
<arg name="remote_host_name" type="s" direction="out"/>
</method>
<method name="GetDisplayDevice">
<arg name="display_device" type="s" direction="out"/>
</method>
<method name="GetX11DisplayDevice">
<arg name="x11_display_device" type="s" direction="out"/>
</method>
<method name="GetX11Display">
<arg name="display" type="s" direction="out"/>
</method>
<method name="GetUnixUser">
<arg name="uid" type="u" direction="out"/>
</method>
<method name="GetUser">
<arg name="uid" type="u" direction="out"/>
</method>
<method name="GetSessionType">
<arg name="type" type="s" direction="out"/>
</method>
<method name="GetSeatId">
<arg name="sid" type="o" direction="out"/>
</method>
<method name="GetId">
<arg name="ssid" type="o" direction="out"/>
</method>
<signal name="Unlock">
</signal>
<signal name="Lock">
</signal>
<signal name="IdleHintChanged">
<arg type="b"/>
</signal>
<signal name="ActiveChanged">
<arg type="b"/>
</signal>
<property name="idle-hint" type="b" access="readwrite"/>
<property name="is-local" type="b" access="readwrite"/>
<property name="active" type="b" access="readwrite"/>
<property name="x11-display-device" type="s" access="readwrite"/>
<property name="x11-display" type="s" access="readwrite"/>
<property name="display-device" type="s" access="readwrite"/>
<property name="remote-host-name" type="s" access="readwrite"/>
<property name="session-type" type="s" access="readwrite"/>
<property name="user" type="u" access="readwrite"/>
<property name="unix-user" type="u" access="readwrite"/>
</interface>
</node>
Note those properties at the end of that list, which are the same things you can learn by running ck-list-session.
If you want to change the deny to allow, you may as well do it in the ConsoleKit.conf line, so it's specific to this usage, rather than allowing any method call in the world called through dbus.
FWIW, I can reproduce this same error, trying to do it "by hand", though I don't use GNOME, as you do:
$ dbus-send --print-reply --system --type=method_call --dest=org.freedesktop.ConsoleKit /org/freedesktop/ConsoleKit/Session1 org.freedesktop.DBus.Properties.GetAll string:org.freedesktop.ConsoleKit.Session
Error org.freedesktop.DBus.Error.AccessDenied: Rejected send message, 2 matched rules; type="method_call", sender=":1.17" (uid=1000 pid=13892 comm="dbus-send --print-reply --system --type=method_cal") interface="org.freedesktop.DBus.Properties" member="GetAll" error name="(unset)" requested_reply="0" destination="org.freedesktop.ConsoleKit" (uid=0 pid=751 comm="/usr/sbin/console-kit-daemon --no-daemon ")

1000's of Returned Mail messages every day!

Hi All,
I am receiving thousands of Returned Mail and Undeliverable Mail messages every day in my Mail application.
Here is the problem description:
I used to have a MobileMe (.mac) account and a corresponding email address. I did not renew my MobileMe account this year. Now, whenever Mail receives any valid message to my existing RoadRunner email address, that same message is being automatically resent to the defunct .mac email address and since it is no longer a valid address, it is being returned to my inbox as Undeliverable or Returned. The same message is being resent apparently many many times for each valid message I receive in my inbox. The result is literally thousands of undeliverable email messages clogging my account. Each time it is resent, it copies all the headers and the original message so by the time the same message is received over and over again the message sizes are well over 2 MB in size! It is an endless repeating cycle.
What I have done so far:
Called RoadRunner - they said to delete and reinstall Mail
Deleted Mail and reinstalled
Deleted Mail preferences
Turned off all iSync functions
Searched for and deleted all references to the invalid .mac email address on my computer
Turned off all notifications from iCal
Upgraded OS from 10.5.x to 10.6.7
None of this has stopped the torrents of messages…PLEASE HELP.
Would not like to have to erase the hard drive and reinstall the OS from scratch if possible.
Here is what a typical returned message header looks like (Email address blocked out by me):
This message was created automatically by the mail system (ecelerity).
A message that you sent could not be delivered to one or more of its
recipients. This is a permanent error. The following address(es) failed:
[email protected] (after RCPT TO): 550 5.1.1 unknown or illegal alias: [email protected]
Reporting-MTA: dns; hrndva-oedge04.mail.rr.com
Arrival-Date: Thu, 28 Apr 2011 13:25:39 +0000
Remote-MTA: dns; nk11b01-smtp-mx006.mac.com
Diagnostic-Code: smtp; 550 5.1.1 unknown or illegal alias: [email protected]
Last-Attempt-Date: Thu, 28 Apr 2011 13:25:39 +0000
Action: failed
Final-Recipient: rfc822; [email protected]
Status: 5.1.1
------ This is a copy of the original message, including all headers. ------
Return-Path: <[email protected]>
X-Authority-Analysis: v=1.1 cv=pN6kzQkhXdmdOr6Akjoh3kGBD/S3UyPMKQp53EJY+ro= c=1 sm=0 a=9Xqw66NJkoB9GertGQDpPQ==:17 a=n-kJSqksAAAA:8 a=nz4EaHi66Edgnas9-7sA:9 a=98jSFH7WqmUA:10 a=ayC55rCoAAAA:8 a=qyzg_sS0DHm6ZXvf9RAA:9 a=udDd3TAlAAAA:8 a=A-Ay9Xv3AAAA:8 a=13-m3CVyAAAA:8 a=Nq7WNfEEaPaVeQek9H8A:9 a=nCRpLGje-JdQZUhY4UwA:7 a=xKgkma0IJD8A:10 a=pdFTHh6Ffp0A:10 a=uqRLPZCTzCUA:10 a=60GRva4_FlB0_GV7:21 a=0a-loXuVl3_jPVwJ:21 a=9Xqw66NJkoB9GertGQDpPQ==:117
X-Cloudmark-Score: 0
X-Originating-IP: 50.90.215.242
From: <[email protected]>
Received: from [50.90.215.242] ([50.90.215.242:47870] helo=[10.0.1.4])
    by hrndva-oedge04.mail.rr.com (envelope-from <[email protected]>)
    (ecelerity 2.2.3.46 r()) with ESMTP
    id 73/88-28036-3CA69BD4; Thu, 28 Apr 2011 13:25:24 +0000
Content-Type: multipart/report; report-type=delivery-status; boundary="lvFcVbMq4Bmrb7Nos44Q+yDizFUn+uvxvchPCg=="
X-Mailer: Apple Mail (2.1084)
Date: Thu, 28 Apr 2011 13:24:24 +0000
Subject: Mail Delivery Failure
Resent-Date: Thu, 28 Apr 2011 09:25:23 -0400
Resent-From: Joe Blow <[email protected]>
To: [email protected]
Resent-To: [email protected]
Message-Id: <[email protected]>
--lvFcVbMq4Bmrb7Nos44Q+yDizFUn+uvxvchPCg==
Content-Type: text/plain
This message was created automatically by the mail system (ecelerity).
A message that you sent could not be delivered to one or more of its
recipients. This is a permanent error. The following address(es) failed:
[email protected] (after RCPT TO): 550 5.1.1 unknown or illegal alias: [email protected]
THANK YOU FOR READING AND HELPING IF YOU CAN.
Bern

Are the returned messages showing all different recipients? If so, it's possible someone has hacked into your MobileMe account and is using it to send out spam.
A brute force spamming will result in thousands of failed return messages. That happens when a spammer sends out mail to a know mail server, such as Hot Mail. They'll send the same message to [email protected], [email protected], etc. Do this for thousands of addresses and many will be returned by the receiving server as undeliverable because there is no user on their system by [email protected], and any other address with no match.
Or, your address is simply being spoofed by a prolific spammer. They picked up your email address as a valid address and are spoofing it in the From field. Doesn't matter that the thousands of emails that went out from them with your name as the sender didn't come from you, the receiving server just assumes it did and you get the bounce messages.
For the first, go in and change your password and see if that stops the flow. For the latter, there's really nothing you can do. Spammers will only use someone's address for a short while. Otherwise, the "from" address gets blacklisted automatically by mail servers, which would cut off the spammer's ability to send out more crap in your name. Then it's someone else who has to put up with it for a few days.

The following organization rejected your message: ESMTP.

Using SBS 2008 with Exchange 2007. I am getting this message from 2 different organizations, but only 2. All other emails go out fine. The bounce back occurs immediately, almost as if it does not even go out. This is a new problem that just surfaced. Any help would be appreciated.
Here is the detail of the error:
Delivery has failed to these recipients or distribution lists:
William O'Dell
An error occurred while trying to deliver this message to the recipient's e-mail address. Microsoft Exchange will not try to redeliver this message for you. Please try resending this message, or provide the following diagnostic text to your system administrator.
The following organization rejected your message: ESMTP.
Sent by Microsoft Exchange Server 2007
Diagnostic information for administrators:
Generating server: PASVR.SynACT2.local
[email protected]
ESMTP #554 Transaction Failed Spam Message not queued. ##
Original message headers:
Received: from PASVR.SynACT2.local ([fe80::d93:c007:477c:9952]) by
PASVR.SynACT2.local ([fe80::d93:c007:477c:9952%10]) with mapi; Tue, 5 May
2009 11:34:43 -0400
From: Ken Compter <[email protected]>
To: William O'Dell <[email protected]>
Date: Tue, 5 May 2009 11:34:41 -0400
Subject: Sales Process Modeling Update
Thread-Topic: Sales Process Modeling Update
Thread-Index: AcnNlwIyBChaPXVdTSmQFWv+VlXTxw==
Message-ID: <[email protected]>
Accept-Language: en-US
Content-Language: en-US
X-MS-Has-Attach: yes
X-MS-TNEF-Correlator:
acceptlanguage: en-US
Content-Type: multipart/related;
            boundary="_007_F3D2E271BE29C3488DA401393DC0099B23F8498B52PASVRSynACT2l_";
            type="multipart/alternative"
MIME-Version: 1.0

Delivery has failed to these recipients or distribution lists:
[email protected]
An error occurred while trying to deliver this message to the recipient's e-mail address. Microsoft Exchange will not try to redeliver this message for you. Please try resending this message, or provide the following diagnostic text to your system administrator.
Diagnostic information for administrators:
Generating server: spamkiller.xxxxxx.com
[email protected]
#< #5.0.0 X-Spam-&-Virus-Firewall; host scoular.com.inbound15.mxlogic.net[208.65.144.12] said: 553 mailbox
[email protected] is restricted (Mode: normal) (in reply to RCPT TO command)> #SMTP#
Original message headers:
X-ASG-Debug-ID: 1335282850-024e85090bb090b0001-eby5OG
Received: from xxxxx.xxx.xx ([192.192.xxx.xxx.xxx]) by xxxxx
with ESMTP id M0Eaq5damCASV5SJ for <[email protected]>; Tue, 24 Apr 2012
10:54:10 -0500 (CDT)
X-Barracuda-Envelope-From: [email protected]
Received: from xxxxx.xxx.xx ([192.192.xxx.xxx.xxx]) by xxxxx
([192.168.10.5]) with mapi; Tue, 24 Apr 2012 10:54:10 -0500
From: "Patel, Arpit" <[email protected]>
X-Barracuda-BBL-IP: 192.xxx.xxx.xxx
X-Barracuda-RBL-IP: 192.xxx.xxx.xxx
To: "'[email protected]'" <[email protected]>
Date: Tue, 24 Apr 2012 10:54:09 -0500
Subject: test
Thread-Topic: test
X-ASG-Orig-Subj: test
Thread-Index: Ac0iMnxtNM4J+DwnSx66abOpTtjmuA==
Message-ID:
FBD890831CAF5048B00FFDDD02D55A640C04310C34@xxxxx
Accept-Language: en-US
Content-Language: en-US
X-MS-Has-Attach:
X-MS-TNEF-Correlator:
acceptlanguage: en-US
Content-Type: multipart/alternative;
boundary="_000_FBD890831CAF5048B00FFDDD02D55A640C04310C34xxxx_"
MIME-Version: 1.0
X-Barracuda-Connect: UNKNOWN[192.xx.xx.xxx
X-Barracuda-Start-Time: 1335282850
X-Barracuda-URL: http://192.xx.xx.xx:000/cgi-mod/mark.cgi
X-Virus-Scanned: by bsmtpd at rlcx.com
X-Barracuda-Spam-Score: 0.00
X-Barracuda-Spam-Status: No, SCORE=0.00 using global scores of TAG_LEVEL=1000.0 QUARANTINE_LEVEL=1000.0 KILL_LEVEL=9.0 tests=HTML_MESSAGE
X-Barracuda-Spam-Report: Code version 3.2, rules version 3.2.2.95041
Rule breakdown below
pts rule name              description
0.00 HTML_MESSAGE           BODY: HTML included in message
Can someone help me? I am having a same issue and not sure what to look for.
Can someone explain how to check this stuff and where?
> Find out which DNSBL lists your IP address.
>
>sir now my Q. is that, where I can found my DNSBL oprator.
That information should be in the text of the 5xx or 4xx status code
returned from the server that rejected your e-mail.
Thanks again for looking.
Arpit Patel

10.5 - 10.6.2: Postfix not accepting e-mails from certain hosts

Hi
Two days ago we migrated our server from 10.5 Server to a new Mac mini server running 10.6.2 server.
We are now facing the problem that postfix refuses to accept incoming e-mails from most hosts. Some hosts seem to be able to get through, but so far we haven't be able to identify a pattern.
The transfers just times out with various error messages. Below is one of the shorter transscripts. Any ideas where to start looking?
Feb 5 18:36:12 www postfix/smtpd[34067]: connect from pluto2-mail.kagi.com[67.134.14.166]
Feb 5 18:36:12 www postfix/smtpd[34067]: setting up TLS connection from pluto2-mail.kagi.com[67.134.14.166]
Feb 5 18:36:13 www postfix/smtpd[34067]: Anonymous TLS connection established from pluto2-mail.kagi.com[67.134.14.166]: TLSv1 with cipher DHE-RSA-AES256-SHA (256/256 bits)
Feb 5 18:36:14 www postfix/smtpd[34067]: 42ABB92A50: client=pluto2-mail.kagi.com[67.134.14.166]
Feb 5 18:41:14 www postfix/smtpd[34067]: warning: networkbiopairinterop: error reading 5 bytes from the network: Connection reset by peer
Feb 5 18:41:14 www postfix/smtpd[34067]: timeout after DATA (986 bytes) from pluto2-mail.kagi.com[67.134.14.166]
Feb 5 18:41:14 www postfix/smtpd[34067]: disconnect from pluto2-mail.kagi.com[67.134.14.166]
Thanks,
Ilja

Hi again,
I was able to further narrow down the problem. The remote server is sending a complete message but postfix on our mac doesn't recognize the end of message token, thus timing out the connection after 5 minutes.
Any ideas? Is this a postfix issue? If so, what can we do about it.
<pre>
0x02e0: 2039 3437 3039 2d31 3430 3520 2055 5341 .94709-1405..USA
0x02f0: 0d0a 5351 4e4d 2d6b 6167 6920 3531 3530 ..SQNM-kagi.5150
0x0300: 0d0a 0d0a 0d0a 0d0a 0d0a 5343 2d54 4659 ..........SC-TFY
0x0310: 5020 352e 3068 0d0a 2e0d 0a P.5.0h.....
19:43:28.538241 IP (tos 0x0, ttl 64, id 8917, offset 0, flags [DF], proto TCP (6), length 64, bad cksum 0 (->9605)!)
www.mydomain.com.smtp > terra.kagi.com.45495: Flags [.], cksum 0x8210 (incorrect -> 0x4852), seq 291, ack 1186, win 33304, options [nop,nop,TS val 928896121 ecr 2567915589,nop,nop,sack 1 {4082:4825}], length 0
0x0000: 4500 0040 22d5 4000 4006 0000 6d46 c4f2 E..@".@[email protected]..
0x0010: 4386 0c1f 0019 b1b7 685e 0685 d895 c111 C.......h^......
0x0020: b010 8218 8210 0000 0101 080a 375d d479 ............7].y
0x0030: 990f 4845 0101 050a d895 cc61 d895 cf48 ..HE.......a...H
</pre>
<pre>
19:48:28.318858 IP (tos 0x0, ttl 64, id 27393, offset 0, flags [DF], proto TCP (6), length 118, bad cksum 0 (->4da3)!)
www.mydomain.com.smtp > terra.kagi.com.45495: Flags [P.], cksum 0x8246 (incorrect -> 0x0c90), seq 291:345, ack 1186, win 33304, options [nop,nop,TS val 928899117 ecr 2567915589,nop,nop,sack 1 {4082:4825}], length 54
0x0000: 4500 0076 6b01 4000 4006 0000 6d46 c4f2 E..vk.@[email protected]..
0x0010: 4386 0c1f 0019 b1b7 685e 0685 d895 c111 C.......h^......
0x0020: b018 8218 8246 0000 0101 080a 375d e02d .....F......7].-
0x0030: 990f 4845 0101 050a d895 cc61 d895 cf48 ..HE.......a...H
0x0040: 3432 3120 342e 342e 3220 7777 772e 6977 421.4.4.2.www.iw
0x0050: 6173 636f 6469 6e67 2e63 6f6d 2045 7272 ascoding.com.Err
0x0060: 6f72 3a20 7469 6d65 6f75 7420 6578 6365 or:.timeout.exce
0x0070: 6564 6564 0d0a eded..
19:48:28.321859 IP (tos 0x0, ttl 64, id 46435, offset 0, flags [DF], proto TCP (6), length 64, bad cksum 0 (->377)!)
www.mydomain.com.smtp > terra.kagi.com.45495: Flags [F.], cksum 0x8210 (incorrect -> 0x3c67), seq 345, ack 1186, win 33304, options [nop,nop,TS val 928899117 ecr 2567915589,nop,nop,sack 1 {4082:4825}], length 0
0x0000: 4500 0040 b563 4000 4006 0000 6d46 c4f2 [email protected]@[email protected]..
0x0010: 4386 0c1f 0019 b1b7 685e 06bb d895 c111 C.......h^......
0x0020: b011 8218 8210 0000 0101 080a 375d e02d ............7].-
0x0030: 990f 4845 0101 050a d895 cc61 d895 cf48 ..HE.......a...H
</pre>
Regards,
Ilja

7230: sending SMTP e-mail, **bleep** is hosting-op...

Hello,
For my e-mail, I have access to an SMTP server which requires authentication for outgoing mail.
However all mail sent from my 7230 do not come from the phone itself and ignores my settings.
-> problem 1: the sender address on the SMTP envelope shows as: SRS0=uFHK0pop=WG=domain.com=[email protected]
Many SMTP receiving sites will reject mail from this sender address, as the sending domain 'SMTP1.SUW.HOSTING-OPS.COM' returns a DNS error. (does not resolve)
-> problem 2 : what is this man-in-the-middle intrusion ? If I configure a sender address and a SMTP server with authorization, why does the phone set establish a conversation with a site that has nothing to see ? Why is my sender address replaced with an invalid address ? The IP address from where the e-mail originates is not my phone IP address. This is also troublesome.
I would be glad to receive any useful information.
Frederic
Brussels

Hello
You said that you have changed your internet connection. If you mean that you have changed your ISP, and this problem rose right after that, your new ISP may have blocked SMTP connections. Some ISPs do this to prevent sending spams via email clients. Please
verify this via your ISP administrator/help desk.
Please further note that you can use ports other than 25 ONLY if your email server is configured to support them. For example, Gmail only supports Secure (SSL) connections on port 465 for outgoing emails, and nothing else! (SSL 995 for incoming, and again
nothing else!) When using secure ports, you need to check "This server requires an encrypted connection (SSL)" for incoming server and/or select appropriate item in "Use the following type of encrypted connection" option for outgoing server
(These options may differ depending on your outlook version. These are for Outlook Professional 2010). Otherwise, your server will not respond your request. I may be able to give you more help if you tell me what email service are you exactly using.
Regards,
Mohammad Javahery

'Connect to Remote Host' is disabled

Hello
We have recently upgraded to CS4. I have imported all of my old connections without problem.
My boss recently asked to show him how to upload files to a certain site. Setup site as usual on his machine, but where I can click my 'Connect to Remote Host' button and see all of the server files, my boss' button is disabled and shows a message about setting up version control first.
We do not want to do this, only to access the server just like we did before. Can version control be turned off? Or is it a different problem?
Thanks in advance for any help.
Gareth

Hi David
Everything that you said is how it is already setup.
Access set to None.
Within Manage Sites > Remote Info all the FTP connection is correct, and has been tested.
He is actually already using the site, but only through GET and PUT commands, never being able to actually see what is on the server!
I created the site on my machine a while ago (before updating to cs4), and I wondered if it was something to do with that? I had just made some amends to the site before setting the FTP up in Dw on my boss' Mac.
As mentioned, below the button, in the space where the server files should display, the message reads "to see the files in the repository you must define the version control settings", which are currently set to NONE.
cheers
Gareth

Rejected mail message: "Remote host said: 550 5.1....

Similar Messages

Maybe you are looking for