Relation between workcenter and Asset

Dear All,
Is there any relation between Work Center and Asset. If there is then how we can see. Or we can find it through Equipment.
Regards
Sunil

Hi Avisesh
The field you indicated in Equipment Location tab (ARBPL) is in fact used to integrate Plant Maintenance with Production Planning; it represents the Production Work Center linked to this Equipment, and allows to automatically block the production capacity during Equipment repair. This is the only usefull functionality of this field.
Of course you can also link an equipment used to perform maintenance tasks to a PM work center, in order to control it's capacity during it's own revisions, but this seems a little overkilling
The Maintenance work center that is assigned by default to perform maintenance activities for the Equipment has to be maintained in the Organization/Responsibilities tab: Main WorkCtr (GEWRK). This will then be automatically copied when you create PM orders & notifications, Equipment Task Lists or maintenance plans with refference to that equipment.
This seems to be a rather frequent mistake done by allmost every junior PM consultant (I did the same some years ago) - it's generated by poor SAP documentation and lack of experience.
Sorry, I can't award you more than -10 (minus ten) points )
Cheers!

Similar Messages

I want to know the relation between Retiremen in assets and AR

i want to know the relation between Retiremen in assets and AR
whene selleing asset in FA and retire it in AR

Hello.
how can i achieve this entry in AR You will have to create it manually. The system does not create it automatically.
and is their any report in FA to identify the sold assetsThe Asset Retirement Report
Octavio

Relation between BSEG with Asset Tables

HI Guru's,
how to find relation between BSEG with Asset Tables like ANLA and ANEP..
regards
JK

Foreign keys
- ANEP items are linked to ANLA via fields in common ANLN1 and ANLN2
- ANEK header is linked to ANEP items via fields in common ANLN1, ANLN2, GJAHR and LNRAN
- BKPF and BSEG are linked to ANEL ANEP via BUKRS, BELNR and GJAHR
Optimization (as BSEG is behind a cluster table RFBLG)
- Append BSIS (ZABSIS) and BSAS with ANLN1 and ANLN2, then create an index with these fields. As BSIS is filled via MOVE-CORRESPONDING statement, only a one-shot report to initially fill the new fields is to be developed. (look at old OSS [Note 62435 - F-03: Selection by purchasing documents|https://service.sap.com/sap/support/notes/62435] for optimization via purchase order)
Regards

Relation between PLM and QM modules

What is the relation between PLM and QM modules?
These two are different modules or QM is one of the module in PLM and there is no module as PLM and its just general term?
Why QM is many times called with PLM - QM?

Hi Sandip,
mySAP PLM has many key features like:
1.Collabarative Engineering and Design.
2. Custom Product Development
3. Knowledge Management
4. Project Management
5.Colloborative Maintenance management
6. QUALITY MANAGEMENT
Begin quality planning during the product design phase, and create a foundation for quality inspection processes and in-process control during production
and Allow employees to play a central role in quality management
and it also Satisfy criteria for ISO 9000 and Good Manufacturing Practice (GMP)
Tracking the Product through out its life from a quality perspective is PLM-QM
The Functionality that Spans the Entire Product & Asset Life Cycle are:
1. Life Cycle Data Management (MM, BOM, DMS, CAD Interface, Classification System)
2. Program & Project Management(Project System, Collaboration Folders, Collaboration Projects, XRPM, xAPPS)
3.QUALITY MANAGEMENT
4. Asset Life-Cycle Managment
5. Environment, Health and Safety.
Regards
Rehman
Reward Your Suitable Points if Helpful

Table relations between vbrk and bkpf for Accounting Document Number

hello,
i am using 4 tables to get data into my programs.
vbrk,vbrp konv and bkpf.
i want to get belnr from bkpf.i found relation between vbrk and belnr.but in vbrk table belnr's value is initial.
can anybody tell me that how should i relate vbrk and bkpf or how to get Accounting Document Number(belnr) from bkpf for Billing Document(vbeln).
regards,
soniya s.

hi,
chekc this. its working for me.
data : WA_AWKEY LIKE BKPF-AWKEY.
data : WA_BELNR LIKE BKPF-BELNR.
data : LENGTH TYPE I.
*BREAK MTABAP.
LENGTH = STRLEN( IT_VBRK-VBELN ).
if LENGTH = '10' .
MOVE it_vbrk-VBELN TO WA_AWKEY.
SELECT SINGLE BELNR FROM BKPF INTO WA_BELNR
WHERE AWKEY = WA_AWKEY
AND AWTYP = 'VBRK'
and blart = 'RV'.
it_final-acc_doc = WA_BELNR.
CLEAR WA_BELNR .
CLEAR WA_AWKEY .
else.
CONCATENATE '0' it_vbrk-vbeln INTO wa_awkey.
SELECT SINGLE BELNR FROM BKPF INTO WA_BELNR
WHERE AWKEY = WA_AWKEY
AND AWTYP = 'VBRK'
and blart = 'RV'.
it_final-acc_doc = WA_BELNR .
CLEAR WA_BELNR .
CLEAR WA_AWKEY.
endif.

How to make relation between gl_je_lines and wip_transaction_accounts

I try to write script to make relation between GL and WIP, wip_transaction_accounts and mtl_material_transactions
1.
SELECT
(SELECT meaning
FROM mfg_lookups
WHERE lookup_type = 'WIP_TRANSACTION_TYPE'
AND lookup_code =
(SELECT TRANSACTION_TYPE
FROM wip_transactions
WHERE transaction_id = wta.transaction_id
) "Transaction Type" ,
gjb.NAME "Journal Batch Name" ,
gjh.NAME "Journal Name" ,
gjh.je_source "JE Source" ,
gjh.je_category "JE Category" ,
glp.period_num "GL Month" ,
glp.period_year "GL Year" ,
gjh.default_effective_date "GL Date" ,
NVL(gje.accounted_dr,0) -NVL( gje.accounted_cr,0) "GL Line Amount" ,
gje.description "GL Line Description" ,
(SELECT organization_code
FROM mtl_parameters
WHERE organization_id = wta.organization_id
) "ORG Name" ,
NULL "Vendor/Customer Name" ,
NULL "SO/PO Number" ,
NULL "Reference Number" ,
NULL "AP/AR Invoice Number" ,
NULL "Doc Sequence Value" ,
NULL "Invoice Type Lookup Code" ,
NULL "Check Number" ,
NULL "Line Type" ,
NULL "Category" ,
NVL (wta.base_transaction_value, 0) "Transaction Amt" ,
NULL "AR/PO Receipt Number" ,
NULL "Applied Invoice Number" ,
(SELECT a.segment1
FROM mtl_system_items_b a ,
wip_discrete_jobs b
WHERE a.inventory_item_id = b.primary_item_id
AND a.organization_id = b.organization_id
AND b.wip_entity_id = wta.wip_entity_id
AND b.organization_id = wta.organization_id
) "Item Name" ,
gcc.segment1 "Company" ,
gcc.segment2 "Department" ,
gcc.segment3 "Account" ,
(SELECT description
FROM fnd_flex_values_vl fnd
WHERE flex_value_set_id = 1009707
AND TO_CHAR (fnd.flex_value) = gcc.segment3
) "Account Description" ,
gcc.segment4 "Intercompany" ,
NULL "JE Category Description" ,
NULL "AP Invoice Line Description"
TRUNC (wta.transaction_date) "JE Creation/Inv Trans Date" ,
NULL "JE Created By" ,
NULL "Reversal Flag" ,
NULL "Reason Code" ,
NULL "Subinventory Name" ,
wta.primary_quantity "Quantity" ,
NVL (wta.base_transaction_value, 0) "Value" ,
gje.context ,
gje.attribute1 ,
gje.attribute2 ,
gje.attribute3 ,
gje.attribute4 ,
gje.attribute5 ,
DECODE(gjh.status,'P','Posted','U','Unposted','Error') "Post Status"
FROM gl_je_lines gje ,
gl_je_headers gjh ,
gl_je_batches gjb ,
wip_transaction_accounts wta ,
gl_code_combinations gcc ,
gl_periods glp
WHERE 1 =1
AND gje.je_header_id = gjh.je_header_id
AND gjh.je_batch_id = gjb.je_batch_id
AND UPPER (gjh.je_source) = 'INVENTORY'
AND gcc.code_combination_id = gje.code_combination_id
AND wta.reference_account = gje.code_combination_id
AND TRUNC(wta.transaction_date) BETWEEN glp.START_DATE AND glp.END_DATE
AND gje.reference_1 = wta.gl_batch_id
AND gje.gl_sl_link_table = 'WTA'
AND glp.period_name = gjh.period_name
AND glp.period_set_name = 'OVT_US_CAL'
==
2.
SELECT mtt.transaction_type_name "Transaction Type" ,to_char(mmt.transaction_date,'mm/dd/yyyy hh:mi:ss') as teas, mta.transaction_id,mta.organization_id, mmt.organization_id,
gjb.NAME "Journal Batch Name" ,
gjh.NAME "Journal Name" ,
gjh.je_source "JE Source" ,
gjh.je_category "JE Category" ,
glp.period_num "GL Month" ,
glp.period_year "GL Year" ,
gjh.default_effective_date "GL Date" ,
NVL(gje.accounted_dr,0) - NVL(gje.accounted_cr,0) "GL Line Amount" ,
gje.description "GL Line Description" ,
(SELECT organization_code
FROM mtl_parameters
WHERE organization_id = mta.organization_id
) "ORG Name" ,
NULL "Vendor/Customer Name" ,
NULL "SO/PO Number" ,
mmt.TRANSACTION_REFERENCE "Reference Number" ,
NULL "AP/AR Invoice Number" ,
NULL "Doc Sequence Value" ,
NULL "Invoice Type Lookup Code" ,
NULL "Check Number" ,
NULL "Line Type" ,
NULL "Category" ,
NVL (mta.base_transaction_value, 0) "Transaction Amt" ,
NULL "AR/PO Receipt Number" ,
NULL "Applied Invoice Number" ,
(SELECT segment1
FROM mtl_system_items_b
WHERE inventory_item_id = mmt.inventory_item_id
AND organization_id = mmt.organization_id
) "Item Name" ,
gcc.segment1 "Company" ,
gcc.segment2 "Department" ,
gcc.segment3 "Account" ,
(SELECT description
FROM fnd_flex_values_vl fnd
WHERE flex_value_set_id = 1009707
AND TO_CHAR (fnd.flex_value) = gcc.segment3
) "Account Description" ,
gcc.segment4 "Intercompany" ,
NULL "JE Category Description" ,
NULL "AP Invoice Line Description"
TRUNC (mta.transaction_date) "JE Creation/Inv Trans Date" ,
NULL "JE Created By" ,
NULL "Reversal Flag" ,
(SELECT MGD.SEGMENT1
FROM MTL_GENERIC_DISPOSITIONS MGD,
MTL_MATERIAL_TRANSACTIONS MMTT
WHERE MGD.DISPOSITION_ID = MMTT.TRANSACTION_SOURCE_ID
AND MMTT.TRANSACTION_SOURCE_TYPE_ID = 6
AND MGD.ORGANIZATION_ID = MMTT.ORGANIZATION_ID
AND MMTT.TRANSACTION_ID = MMT.TRANSACTION_ID
) "Reason Code" ,
mmt.SUBINVENTORY_CODE "Subinventory Name" ,
mta.primary_quantity "Quantity" ,
NVL (mta.base_transaction_value, 0) "Value" ,
gje.context ,
gje.attribute1 ,
gje.attribute2 ,
gje.attribute3 ,
gje.attribute4 ,
gje.attribute5 ,
DECODE(gjh.status,'P','Posted','U','Unposted','Error') "Post Status" -
FROM gl_je_lines gje ,
gl_je_headers gjh ,
gl_je_batches gjb ,
mtl_transaction_accounts mta ,
mtl_material_transactions mmt ,
mtl_transaction_types mtt ,
gl_code_combinations gcc ,
gl_periods glp
WHERE 1 =1
AND mta.transaction_id = mmt.transaction_id
AND gje.je_header_id = gjh.je_header_id
AND gjh.je_batch_id = gjb.je_batch_id
AND UPPER (gjh.je_source) = 'INVENTORY'
AND gcc.code_combination_id = gje.code_combination_id
AND mta.reference_account = gje.code_combination_id
AND TRUNC(mta.transaction_date) BETWEEN glp.START_DATE AND glp.END_DATE
and mta.request_id=mmt.request_id
and mta.inventory_item_id=mmt.inventory_item_id
AND gje.reference_1 = mta.gl_batch_id
AND gje.gl_sl_link_table = 'MTA'
AND mtt.transaction_type_id = mmt.transaction_type_id
AND glp.period_name = gjh.period_name
AND glp.period_set_name = 'OVT_US_CAL'
When gl_je_lines have multiple line this script on the same transaction_id it will get wrong information. By setup all wip_transaction_accounts.GL_SL_Lind_id and mtl_transaction_accounts.GL_SL_Lind_id is null
Anyone can help?

Hello.
How are you reaching the inconsistencies ? Are you comparing report's results?
Octavio

Database table/FM to find relation between plant and company code in SRM

Hi,
I have a requirement where I need to determine the relation between the plant and company code in SRM.
The plant and company code both belong to R/3. We are replicating the plant by using the report BBP_LOCATIONS_GET_ALL.
This plant is now available as a BP in SRM. But from which SRM table or using which SRM FM can I get the relation between this and the company code?
Thanks,
Srivatsan

Hi
Check table BBP_LOCMAP. (Plants) - Manage Table Business Partner > System > Location
BBP_COMPCODE_FAV User-Specific Favorites for Permitted Company code.
Hope this will help.
Please reward suitable points, incase it suits your requirements.
Regards
- Atul

Relation between Rollup and compression.

Hi All,
Is there a relation between rollup and compression ? i.e if i compress the cube, will the rollup job be faster ?

Hi,
Thanks for all your replies. Now the picture is crystal clear.
1. A compression job moves data from F table to E table. This is also applicable for aggregates. If you schedule a compression job for a cube, the aggregates are automatically compressed( You can also compress aggregates of a cube without compressing the cube. There are programs avalibale for the same).
2. Assume that you have not done compression . If you load the data to base cube ,it takes more time to create the indexes after loading.
3) Assume that you have done compression . If you load the data to base cube ,it takes less time than 2 point to create the indexes after loading.
On similar lines, if aggregates of a cube are compressed before rollup, then rollup will be faster. This is what exactly I have experienced. I had a cube which had 1000 request. It was never compressed. The rollup job for the cube used to take around 60,000 seconds. I compressed 900 requests. Now the rollup job gets over in 2400 seconds.So the conclusion is the following:
When aggregates of a cube are compressed, the rollup job runs faster.
Message was edited by: Tej Trivedi

Table that gives the relation between plant and company code

Hi gurus,
I actually have plant number and using this plant value i need to get the company code.
Is there any table that gives the relation between plant and company code. So,that i can get the company code details.
Thanks in advance.

Hi Bhanuphani,
Use T001K where BWKEY is the plant
Reward if useful
Thanks Arjun

Is any relation between customerNo and Plant in R/3

hi,
in bapi_salesorder_cretefromdat2 i can get netprice by giving import parameters like customerNo,salesArea,material, etc.......That means customer should be assinged to a plant(one sales area can have many plants( material price can vary from plant to plant) .pls give me clear picture on how net price is calculated in bapi_salesorder_createfromdat2.
regards
Guru

There is a relation between customer and plant in the KNA1 General Data in Customer Master table.
kna1-kunnr
kna1-werks.
Kindly reward the points

Is There any Relation Between PCD and SSO

Hi,
Is there any relation between PCD and SSO, why because if i am try to connect from portal to R/3 in the user mapping i got one error i.e some pcd error.
pls tell me how to rectify that.
Regards,
Jagadish Babu Kanikanti.

Hi Jagadish
The PCD is only a central persistance for storing Portal objects. There is no such relation between PCD and SSO that could create a problem. You can however check for the PCD error in this manner.
1. In the system administration role, choose System Administration -> Support. The Support Desk appears.
2. Select the area Portal Content Directory.
3. Click on PCD Configuration in the test and configuration tools. The next screen shows all the parameter values currently maintained for the PCD.
4. To reload the configuration, choose Reload.
Hope that helped.
Best Regards
Priya

Can any one explain me the relation between BDC and reports events?

hi experts.....
can any one explain me the relation between BDC and reports events? we are using report events in BDC programmes why?\
Is reports events occurs in each and every concept in ABAP i.e creating custom idocs, smart forms, sap scripts, dialog programmes, module pool technics?
thanks in advance

The forums are expert forums. So the first thing I would do is change your name.
It's like entering a grand prix in a car with a "Student Driver" sign.
Rob

Urgent :Relation between vendor and business area

< MODERATOR: Message locked. Please read the [Rules of Engagement|https://www.sdn.sap.com/irj/sdn/wiki?path=/display/home/rulesofEngagement] before posting next time. >
Hi ,
Is there any table or transaction which will give an one-to-one relation between vendor and business area?
Thnks and Regards,
Anand

hi
in this situation u have to creat new Z table and Z transaction with link of this both . it will solve ur problem . better to take abaper help other wise u can use T-CODE se11 to creat table.
se93 for transaction code .

How to get data from three tables (A,B,C) having one to many relation between A and B .and having one to many reation between b and c

i have three tables A,B,C. there is one to many relation between A and B. and one to many relation existed between table b and c . how will get data from these three tables

check if this helps:
select * --you can always frame your column set
from tableA a
left join tableB b on a.aid=b.aid
left join tableC c on c.bid=b.bid
This is just a general query. However, we can help you a lot more, if you can post the DDL + sample data and required output.
Thanks,
Jay
<If the post was helpful mark as 'Helpful' and if the post answered your query, mark as 'Answered'>

What are the Relations between Journalizing and IKM?

What is the best method to use in the following scenario:
I have about 20 source tables with large amount of data.
I need to create interfaces that join the source tables into target tables.
The source tables are inserted every few secondes with about hundreds to thousands rows.
There can be a gap of few seconds between the insert of different tables that sould be joined.
The source and target tables are on the same Oracle instance and schema.
I want to understand the role of: 'Journalizing CDC' and 'IKM - Incremental Update' and
how can i use it in my scenario?
In general What are the relations between 'Journalizing' and 'IKM'?
Should i use both of them? Or maybe it is better to deelte and insert to the target tables?
I want to understand what is the role of 'Journalizing CDC'?
Can 'IKM - Incremental Update' work without 'Journalizing'?
Does 'Journalizing' need to have PK on the tables?
What should i do if i can't put PK (there can be multiple identical rows)?
Thanks in advance Yael

Hi Yael,
I will try and answer as many of your points as I can in one post :-)
Journalizing is way of tracking only changed data in your source system, if your source tables had a date_modified you could always use this as a filter when scanning for changes rather than CDC, Log based CDC (Asynchronous in ODI, Logminer/Streams or Goldengate for example) removes the overhead of of placing a trigger on the source table to track changes but be aware that it doesnt fully remove the need to scan the source tables, in answer to you question about Primary keys, Oracle CDC with ODI will create an unconditional log group on the columns that you have defined in ODI as your PK, the PK columns are tracked by the database and presented in a Journal table (J$<source_table_name>) this Journal table is joined back to source table via a journalizing view (JV$<source_table_name>) to get the rest of the row (ie none PK columns) - So be aware that when ODI comes around to get all data in the Journalizing view (ie Inserts, Updates and Deletes) the source database performs a join back to the source table. You can negate this by specifying ALL source table columns in your PK in ODI - This forces all columns into the unconditional log group, the journal table etc. - You will need to tweak the JKM to then change the syntax sent to the database when starting the journal - I have done this in the past, using a flexfield in the datastore to toggle 'Full Column' / 'Primary Key Cols' to go into the JKM set up (there are a few Ebusiness suite tables with no primary key so we had to do this) - The only problem with this approach is that with no PK , you need to make sure you only get the 'last' update and in the right order to apply to your target tables, without so , you might process the update before the insert for example, and be out of sync.
So JKM's provide a mechanism for 'Change data only' to be provided to ODI, if you want to handle deletes in your source table CDC is usefull (otherwise you dont capture the delete with a normal LKM / IKM set up)
IKM Incremental update can be used with or without JKM's, its for integrating data into your target table, typically it will do a NOT EXISTS or a Minus when loading the integration table (I$<target_table_name>) to ensure you only get 'Changed' rows on the load into the target.
user604062 wrote:
I want to understand the role of: 'Journalizing CDC' and 'IKM - Incremental Update' and
how can i use it in my scenario?Hopefully I have explained it above, its the type of thing you really need to play around with, and throroughly review the operator logs to see what is actually going on (I think this is a very good guide to setting it up : http://soainfrastructure.blogspot.ie/2009/02/setting-up-oracle-data-integrator-odi.html)
In general What are the relations between 'Journalizing' and 'IKM'?JKM simply presents (only) changed data to ODI, it removes the need for you to decide 'how' to get the updates and removes the need for costly scans on the source table (full source to target table comparisons, scanning for updates based on last update date etc)
Should i use both of them? Or maybe it is better to deelte and insert to the target tables?Delete and insert into target is fine , but ask yourself how do you identify which rows to process, inserts and updates are generally OK , to spot a delete you need to compare the table in full, target table minus source table = deleted rows , do you want to copy the whole source table every time to perform this ? Are they in the same database ?
I want to understand what is the role of 'Journalizing CDC'?Its the ODI mechanism for configuring, starting, stopping the change data capture process in the source systems , there are different KM's for seperate technologies and a few to choose for Oracle (Triggers (Synchronous), Streams / Logminer (Asynchronous), Goldengate etc)
Can 'IKM - Incremental Update' work without 'Journalizing'?Yes of course, Without CDC your process would look something like :
Source target ----< LKM >---- Collection table (C$) ----<IKM>---- Integration table (I$) -----< IKM >---- Target table
With CDC your process looks like :
Source Journal (J$ table with JV$ view) ----< LKM >---- Collection table (C$) ----<IKM>---- Integration table (I$) -----< IKM >---- Target table
as you can see its the same process after the source table (there is an option in the interface to enable the J$ source , the IKM step changes with CDC as you can use 'Synchronise Journal Deletes'
Does 'Journalizing' need to have PK on the tables?Yes - at least a logical PK in the datastore, see my reply at the top for reasons why (Log Groups, joining back the J$ table to the source table etc)
What should i do if i can't put PK (there can be multiple identical rows)? Either talk to the source system people about adding one, or be prepared to change the JKM (and maybe LKM, IKM's) , you can try putting all columns in the PK in ODI. Ask yourself this , if you have 10 identical rows in your source and target tables, and one row gets updated - how can you identify which row in the target table to update ?
>
Thanks in advance YaelA lot to take in, as I advised I would reccomend you get a little test area set up and also read the Oracle database documentation on CDC as it covers a lot of the theory that ODI is simply implementing.
Hope this helps!
Alastair

Relation between workcenter and Asset

Similar Messages

Maybe you are looking for