Reliability 255/255, txload 1/255, rxload 1/255
I can't seem to find the meaning of the following parameters when the sh int command is performed: reliability 255/255, txload 1/255, rxload 1/255..
Can someone please shed the light on it?
Thanks.
It's kind of a rough scale of the condition of the interface.
Reliability 255/255= 100% up and reliable
128/255 = 50% up and not-so reliable
txload 1/255 = 0-4% of traffic is coming from transmitted info. 128/255 would mean 50%of traffic is coming from transmitted info.
rxload is the same as tx except it's received data.
These values are kind of a high level dashboard on what the intreface is doing in regards to traffic. EIGRP Metrics are designed to use the reliability information, but is rarely imlemented.
FROM CISCO
Reliability of the interface as a fraction of 255 (255/255 is 100 percent reliability), calculated as an exponential average over 5 minutes.
txload/rxload=Load on the interface as a fraction of 255 (255/255 is completely saturated), calculated as an exponential average over 5 minutes.
http://www.cisco.com/en/US/products/sw/iosswrel/ps5207/products_command_reference_chapter09186a00801a7edb.html#wp1229983
Similar Messages
-
Cisco 6509 with Reliability 255/255, txload 238/255, rxload 8/255 interface
Hi there,
I'm having an issue with my Cisco 6509. One of Internet configured as trunk Interface direct with a HP7500 is showing reliability 255/255, txload 238/255, rxload 8/255.
The Issue is that my Cacti Server show me that only 10% of the link is in use but if you look at txload you can see that almost 100% of the bandwidth is in use..
What can I do in order to figure out what's going on with this Interface. I'm thing about to put wireshark and configure a port monitor in order to capture the packets.
Is anyone has any tip to do a troubleshoot with this issue??
SWITCH01#show int port-channel 10
Port-channel10 is up, line protocol is up (connected)
Hardware is EtherChannel, address is c47d.4fbf.a8c2 (bia c47d.4fbf.a8c2)
Description: CORECISCO_X_COREHP
MTU 1500 bytes, BW 2000000 Kbit, DLY 10 usec,
reliability 255/255, txload 238/255, rxload 8/255
Encapsulation ARPA, loopback not set
Full-duplex, 1000Mb/s
input flow-control is off, output flow-control is unsupported
Members in this channel: Gi8/19 Gi8/20
ARP type: ARPA, ARP Timeout 04:00:00
Last input never, output never, output hang never
Last clearing of "show interface" counters 1w0d
Input queue: 0/2000/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 66043000 bits/sec, 23041 packets/sec
5 minute output rate 1871148000 bits/sec, 186439 packets/sec
15127300343 packets input, 6121405739799 bytes, 0 no buffer
Received 232321316 broadcasts (161670914 multicast)
0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 watchdog, 0 multicast, 0 pause input
0 input packets with dribble condition detected
118621325538 packets output, 141124879219641 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier, 0 PAUSE output
0 output buffer failures, 0 output buffers swapped out
SWITCH01#
Regards
AdrianoThis pretty much tells you your port channel is pretty full. How many ports in the channel?
5 minute input rate 66043000 bits/sec, 23041 packets/sec
5 minute output rate 1871148000 bits/sec, 186439 packets/sec -
Wireless slowed down, AP LAN interface txload 255/255
Hello
Just built up a new office network, have 5 2602i controlled by a 5508 on FlexConnect local switching mode. One day ago when I tested my wirless, I can got full speed, about 40M, but today, after some 40-50 staff moved in, no configuration is changed, but I can only get 4-5M on speed test when connecting on wirless, but at the same time when connected on cable number, still got full speed, so not an internet link issue.
I checked around, only odd thing I noticed, is that all my 5 APs LAN port, int g0, showed txload 255/255, alrought very low bps and pps on the port.
GigabitEthernet0 is up, line protocol is up
Hardware is PowerPC Ethernet, address is 5087.89e2.bf52 (bia 5087.89e2.bf52)
MTU 1500 bytes, BW 1000000 Kbit/sec, DLY 10 usec,
reliability 255/255, txload 255/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Full Duplex, 1Gbps, media type is T
output flow-control is unsupported, input flow-control is unsupported
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:00:00, output never, output hang never
Last clearing of "show interface" counters 00:00:18
Input queue: 0/22852/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 2000 bits/sec, 2 packets/sec
5 minute output rate 1000 bits/sec, 1 packets/sec
60 packets input, 6703 bytes, 0 no buffer
Received 36 broadcasts (0 IP multicasts)
0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 watchdog, 0 multicast, 0 pause input
36 packets output, 7796 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 unknown protocol drops
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier, 0 pause output
0 output buffer failures, 0 output buffers swapped out
how could I got txload 255/255 whne there was only 1k bps output?
suspect this is the reason slowed down my wireless, but why, and how can I fix it?
thanks a lot.the txload 255/255 is on a AP's G0 port, not on the connected 4500 switch port.
my 4510 is on ver 15.0(1r)SG5
cisco WS-C4510R+E (MPC8572) processor (revision 10) with 2097152K/20480K bytes of memory.
Processor board ID FXS1818Q19K
MPC8572 CPU at 1.5GHz, Supervisor 7
my AP os
Cisco IOS Software, C2600 Software (AP3G2-K9W8-M), Version 15.2(2)JB3, RELEASE SOFTWARE (fc1)
cisco AIR-CAP2602I-Z-K9 (PowerPC) processor (revision A0) with 180214K/81920K bytes of memory.
Processor board ID FGL1825W9Q8
PowerPC CPU at 800Mhz, revision number 0x2151
Last reset from power-on
LWAPP image version 7.4.121.0 -
Need OID for rxload and input rate
Hi all,
I want to monitor the rxload and input rate on interfaces but I can't find the correct OID can someone help me with this please.
Can someone also provideme a good document for this
GigabitEthernet4/8 is up, line protocol is up (connected)
Hardware is Gigabit Ethernet Port, address is 000d.657d.3387 (bia 000d.657d.3387)
Description: --- 2924_MAIN ---
MTU 1500 bytes, BW 100000 Kbit, DLY 10 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Half-duplex, 100Mb/s, link type is auto, media type is 10/100/1000-TX
input flow-control is off, output flow-control is off
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:00:47, output never, output hang never
Last clearing of "show interface" counters 20w1d
Input queue: 0/2000/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 5000 bits/sec, 4 packets/sec
5 minute output rate 153000 bits/sec, 26 packets/sec
143271178 packets input, 34567505950 bytes, 0 no buffer
Received 2731549 broadcasts (295416 multicast)
0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 input packets with dribble condition detected
253476590 packets output, 117220536494 bytes, 0 underruns
1341644 output errors, 542074 collisions, 0 interface resets
0 babbles, 259071 late collision, 0 deferred
0 lost carrier, 0 no carrier
0 output buffer failures, 0 output buffers swapped outHi,
I haven't been able to find any documentation on CCo regarding this, but in my searching, I have come across the following MIb Object, which will tell you the input rate on the interface :
.1.3.6.1.4.1.9.2.2.1.1.6
locIfInBitsSec OBJECT-TYPE
-- FROM OLD-CISCO-INTERFACES-MIB
SYNTAX Integer
MAX-ACCESS read-only
STATUS Mandatory
DESCRIPTION "Five minute exponentially-decayed moving average of input bits per second."
There is a similar object locIfOutBitsSec (.1.3.6.1.4.1.9.2.2.1.1.8) for the output rate.
To so rxload = 255 * locIfInBitsSec / (1000000 * ifHighSpeed )
Regards
Derek -
AP1231G-A-K9 access points - very slow throughput - Is TKIP the issue?
I recently setup our small office network using the following setup:
Cablemodem <--> router <--> 1231AP(role root bridge with wireless clients) <-> 1231AP(role non-root bridge with wireless clients)
Code on both APs: 12.3(8)JEE
Office network generally has less than 3 wireless clients connected at any one time to either AP.
AP's are a mere 50' apart; clients are all less than 30' from either AP; they all show excellent signal and connected at 54mbps signaling rates.
All is/has been working very well & very stable with the exception of speed. We have business class service from RR, approx 25mbps dl, 2mbps ul. Any hardwired client to the router switch ports are able to download at speeds averaging 23mbps. Any wireless client connected to either AP is never able to exceed download speeds of 5mbps. With no other wireless clients connected except my one test client, I was not able to exceed 5mbps throughput from either AP that I connected to.
I can confirm that the ethernet connection between the router and root bridge is up at 100mbps-FD and not showing any errors:
ap#sh interfaces FastEthernet0
FastEthernet0 is up, line protocol is up
Hardware is PowerPC405GP Ethernet, address is 0013.60cf.bb29 (bia 0013.60cf.bb29)
MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Full-duplex, 100Mb/s, MII
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:00:00, output 00:00:00, output hang never
Last clearing of "show interface" counters never
Input queue: 0/160/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 5000 bits/sec, 0 packets/sec
5 minute output rate 1000 bits/sec, 1 packets/sec
8054605 packets input, 3141009145 bytes
Received 46005 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 watchdog
0 input packets with dribble condition detected
4076106 packets output, 411952731 bytes, 0 underruns
0 output errors, 0 collisions, 4 interface resets
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier
0 output buffer failures, 0 output buffers swapped out
Wandering thru the cli on either AP shows that all wireless clients are indeed connected at 54mbps to their respective AP and the two AP's are connected happily at 54mbps signaling:
Address : 0013.1a37.b3e0 Name : ap
IP Address : 192.168.0.120 Interface : Dot11Radio 0
Device : 11g-bridge Software Version : 12.3
CCX Version : NONE
State : Assoc Parent : Our Parent
SSID : Tsunami
VLAN : 0
Hops to Infra : 0 Association Id : 44
Tunnel Address : 0.0.0.0
Key Mgmt type : WPA PSK Encryption : TKIP
Current Rate : 54.0 Capability : WMM ShortHdr ShortSlot
Supported Rates : 1.0 2.0 5.5 6.0 9.0 11.0 12.0 18.0 24.0 36.0 48.0 54.0
Voice Rates : disabled
Signal Strength : -51 dBm Connected for : 75169 seconds
Signal to Noise : 26 dB Activity Timeout : 14 seconds
Power-save : Off Last Activity : 1 seconds ago
Apsd DE AC(s) : NONE
Packets Input : 1050695 Packets Output : 296536
Bytes Input : 474651248 Bytes Output : 96734573
Duplicates Rcvd : 0 Data Retries : 63646
Decrypt Failed : 0 RTS Retries : 0
MIC Failed : 0 MIC Missing : 0
Packets Redirected: 0 Redirect Filtered: 0
Here is a config snippet from the AP non-root bridge with wireless clients:
dot11 ssid Tsunami
authentication open
authentication key-management wpa
guest-mode
infrastructure-ssid optional
wpa-psk ascii 7 (snipped)
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
encryption mode ciphers tkip
ssid Tsunami
speed basic-1.0 2.0 5.5 6.0 9.0 11.0 12.0 18.0 24.0 36.0 48.0 54.0
station-role non-root bridge wireless-clients
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 spanning-disabled
interface FastEthernet0
no ip address
no ip route-cache
duplex auto
speed auto
bridge-group 1
bridge-group 1 spanning-disabled
interface BVI1
ip address dhcp client-id FastEthernet0
no ip route-cache
bridge 1 route ip
(The AP root-bridge with wireless clients config is identical to this config with the exception of the station-role and a static IP on the BVI1 interface.)
Are these very slow thoughput speeds normal of this hardware combination?
I did much searching/googling and found claims that by eliminating TKIP it almost doubles the actual wireless speeds our clients can obtain. Is there any truth to this?
Any suggestions or recommendations without changing hardware would be very welcome.
Thanks in Advance!
D.
=============Ok, thanks for the explanation - I understand. But even at a 22mbps signaling rate shouldn't I be seeing throughputs greater than 5-5.5mbps especially since this location is literally 100% free of any outside interference and the interfaces definitely show the clients and non-root bridge (when connected) all being at the highest rate of 54mbps? I tried even in the same room, approximately 40' away, total line of sight, no obstructions, between my laptop and the root AP.
I disconnected the non-root bridge and connected directly to the root bridge during my testing. I was still only able to achieve approx 5.5mbps download. Adding back in the non-root bridge and re-connecting to it I notice slightly lower throughput, approx 5mbps. During testing, my laptop was the only device connected to the network, all other clients were shut off.
Here are the int stats (I've never reset the counters):
Root Bridge:
RATE 1.0 Mbps
Rx Packets: 2178725 / 49 Tx Packets: 39 / 0
Rx Bytes: 335124036 /7595 Tx Bytes: 4965 / 0
RTS Retries: 61 / 0 Data Retries: 5 / 0
Non-Root-Bridge:
RATE 1.0 Mbps
Rx Packets: 2323120 / 50 Tx Packets: 141 / 0
Rx Bytes: 336455923 /7595 Tx Bytes: 17869 / 0
RTS Retries: 2 / 0 Data Retries: 56 / 0
All the other rates, 2-12mbps show single or double digit packet/byte counts until I get to the 36mbps section of each interface:
ap#sh int Dot11Radio0 stati
DOT11 Statistics (Cumulative Total/Last 5 Seconds):
(snipped for brevity)
Root Bridge:
RATE 36.0 Mbps
Rx Packets: 915395 / 1 Tx Packets: 2345589 / 9
Rx Bytes: 93420936 / 70 Tx Bytes: 3370791285 / 874
RTS Retries: 0 / 0 Data Retries: 573981 / 4
RATE 48.0 Mbps
Rx Packets: 2163192 / 2 Tx Packets: 216861 / 0
Rx Bytes: 222455730 / 404 Tx Bytes: 182817967 / 0
RTS Retries: 0 / 0 Data Retries: 106808 / 0
RATE 54.0 Mbps
Rx Packets: 987986 / 0 Tx Packets: 168923 / 0
Rx Bytes: 190467269 / 0 Tx Bytes: 61665042 / 0
RTS Retries: 0 / 0 Data Retries: 34424 / 0
Non-Root Bridge:
RATE 36.0 Mbps
Rx Packets: 2368679 / 0 Tx Packets: 965419 / 0
Rx Bytes: 3396819830 / 0 Tx Bytes: 90880825 / 0
RTS Retries: 0 / 0 Data Retries: 242686 / 0
RATE 48.0 Mbps
Rx Packets: 341870 / 0 Tx Packets: 2156282 / 1
Rx Bytes: 216497093 / 0 Tx Bytes: 215775536 / 210
RTS Retries: 0 / 0 Data Retries: 478619 / 0
RATE 54.0 Mbps
Rx Packets: 1469926 / 15 Tx Packets: 2529678 / 15
Rx Bytes: 411722698 /1122 Tx Bytes: 1366306113 /5159
RTS Retries: 0 / 0 Data Retries: 198532 / 0
I will try disabling the rates below 12mbps and re-test.
I would like to try disabling all encryption and try as well.
Do you know if the AP's will associate if there is zero encryption? -
Lan connectivity Issue on autonomous AP with throttles
Hello,
I encounter a strange problem on several AP 1242 in version 12.4(25d)JA1 of a customer :
He has 10 autonomous AP covering a factory and is using them for laptop connectivity and TOIP with mainly 7921 Cisco Wifi Phones.
The phones are configured to use only 802.11a.
The APs loose LAN connectivity randomly and therefore the clients don't work anymore.
The AP are connected on a 2960 and a 3560 wich are in turn connected on a 3750 wich route the trafic.
After checking spanning-tree no loops are present.
When I check the counters on the AP involved I see the "trhottles" and "ignored" counters incrementing on the fa0 link of the AP impacted wich mean I think it can't handle the incoming traffic. This incoming traffic seems not to be too big however. I can see drops on the switch interface connecting the AP.
There is a lot of roaming on the AP due to people walking in the factory with their wifi phones.
Here is a view of the fa0 counters :
AP1242-LOGIST#sh int fa0
FastEthernet0 is up, line protocol is up
Hardware is PowerPCElvis Ethernet, address is 001d.a1ce.26e2 (bia 001d.a1ce.26e2)
MTU 1500 bytes, BW 100000 Kbit/sec, DLY 100 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Full-duplex, 100Mb/s, MII
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:00:00, output 00:00:00, output hang never
Last clearing of "show interface" counters never
Input queue: 0/160/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 81000 bits/sec, 53 packets/sec
5 minute output rate 29000 bits/sec, 26 packets/sec
7447113 packets input, 674891974 bytes
Received 286839 broadcasts, 0 runts, 0 giants, 549631 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 549631 ignored
0 watchdog
0 input packets with dribble condition detected
4422100 packets output, 609868806 bytes, 0 underruns
0 output errors, 0 collisions, 4 interface resets
1 unknown protocol drops
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier
0 output buffer failures, 0 output buffers swapped out
Here is a small part of logs concerning roaming, i don't see errors or log indicating that something is wrong nor in the switches log :
Jun 6 12:57:27.007: %DOT11-6-ASSOC: Interface Dot11Radio1, Station SEP001E4A3EE15D 001e.4a3e.e15d Associated KEY_MGMT[WPAv2 PSK]
Jun 6 12:57:42.499: %DOT11-6-ASSOC: Interface Dot11Radio1, Station SEP588D09D3A92B 588d.09d3.a92b Reassociated KEY_MGMT[WPAv2 PSK]
Jun 6 12:58:02.620: %DOT11-6-DISASSOC: Interface Dot11Radio1, Deauthenticating Station 588d.09d3.a92b Reason: Sending station has left the BSS
Jun 6 12:58:03.653: %DOT11-6-ASSOC: Interface Dot11Radio1, Station SEP588D09D3A92B 588d.09d3.a92b Reassociated KEY_MGMT[WPAv2 PSK]
Jun 6 12:59:15.564: %DOT11-6-ROAMED: Station 588d.09d3.a92b Roamed to 001e.134c.5a50
Jun 6 12:59:15.564: %DOT11-6-DISASSOC: Interface Dot11Radio1, Deauthenticating Station 588d.09d3.a92b Reason: Sending station has left the BSS
Jun 6 12:59:41.905: %DOT11-6-DISASSOC: Interface Dot11Radio1, Deauthenticating Station 442b.0355.ab28 Reason: Previous authentication no longer valid
Jun 6 12:59:54.728: %DOT11-6-ASSOC: Interface Dot11Radio1, Station SEP442B0355AB28 442b.0355.ab28 Associated KEY_MGMT[WPAv2 PSK]
Jun 6 13:01:12.541: %DOT11-6-ASSOC: Interface Dot11Radio1, Station SEP588D09D3A92B 588d.09d3.a92b Reassociated KEY_MGMT[WPAv2 PSK]
Jun 6 13:02:35.841: %DOT11-6-DISASSOC: Interface Dot11Radio1, Deauthenticating Station 001e.4a3e.d875 Reason: Previous authentication no longer valid
Jun 6 13:02:36.489: %DOT11-6-ASSOC: Interface Dot11Radio0, Station ec85.2f7c.c837 Associated KEY_MGMT[WPAv2 PSK]
Jun 6 13:03:29.256: %DOT11-6-ROAMED: Station 588d.09d3.a92b Roamed to 001e.134c.5a50
Jun 6 13:03:29.256: %DOT11-6-DISASSOC: Interface Dot11Radio1, Deauthenticating Station 588d.09d3.a92b Reason: Sending station has left the BSS
Jun 6 13:04:32.754: %DOT11-6-ASSOC: Interface Dot11Radio1, Station SEP001E4A3ED875 001e.4a3e.d875 Associated KEY_MGMT[WPAv2 PSK]
Jun 6 13:06:47.858: %DOT11-6-DISASSOC: Interface Dot11Radio1, Deauthenticating Station 001e.4a3e.e15d Reason: Previous authentication no longer valid
Jun 6 13:07:18.107: %DOT11-6-ROAMED: Station 001f.6c7a.5101 Roamed to 001d.a2bb.15b0
Jun 6 13:07:18.107: %DOT11-6-DISASSOC: Interface Dot11Radio1, Deauthenticating Station 001f.6c7a.5101 Reason: Sending station has left the BSS
Jun 6 13:07:38.109: %DOT11-6-ASSOC: Interface Dot11Radio1, Station SEP588D09D3A92B 588d.09d3.a92b Reassociated KEY_MGMT[WPAv2 PSK]
Jun 6 13:07:42.031: %DOT11-6-ROAMED: Station 588d.09d3.a92b Roamed to 001e.134c.5a50
Jun 6 13:07:42.031: %DOT11-6-DISASSOC: Interface Dot11Radio1, Deauthenticating Station 588d.09d3.a92b Reason: Sending station has left the BSS
Jun 6 13:07:46.489: %DOT11-6-ASSOC: Interface Dot11Radio1, Station SEP001F6C7A5101 001f.6c7a.5101 Reassociated KEY_MGMT[WPAv2 PSK]
Jun 6 13:08:27.712: %DOT11-6-ASSOC: Interface Dot11Radio1, Station SEP588D09D3A92B 588d.09d3.a92b Reassociated KEY_MGMT[WPAv2 PSK]
Jun 6 13:08:44.502: %DOT11-6-DISASSOC: Interface Dot11Radio1, Deauthenticating Station 588d.09d3.a92b Reason: Sending station has left the BSS
Jun 6 13:08:44.572: %DOT11-6-ASSOC: Interface Dot11Radio1, Station SEP588D09D3A92B 588d.09d3.a92b Associated KEY_MGMT[WPAv2 PSK]
Jun 6 13:08:56.778: %DOT11-6-ROAMED: Station 588d.09d3.a92b Roamed to 001e.134c.5a50
Jun 6 13:08:56.779: %DOT11-6-DISASSOC: Interface Dot11Radio1, Deauthenticating Station 588d.09d3.a92b Reason: Sending station has left the BSS
Jun 6 13:09:17.874: %DOT11-6-ROAMED: Station 001f.6c7a.5101 Roamed to 003a.9a92.8d70
Jun 6 13:09:17.874: %DOT11-6-DISASSOC: Interface Dot11Radio1, Deauthenticating Station 001f.6c7a.5101 Reason: Sending station has left the BSS
The AP are configured as follow :
Current configuration : 5184 bytes
! No configuration change since last restart
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname AP1242-LOGIST
logging rate-limit console 9
aaa new-model
aaa authentication login default local
aaa authorization exec default local
aaa session-id common
clock timezone gmt+1 1
clock summer-time gmt recurring last Sun Mar 2:00 last Sun Oct 3:00
dot11 syslog
dot11 vlan-name Data vlan 11
dot11 vlan-name Voix vlan 14
dot11 vlan-name Webguest vlan 5
dot11 ssid WLAN_data
vlan 11
authentication open
authentication key-management wpa
mbssid guest-mode
wpa-psk ascii 7 10600C0E261B173C252203797479633F371A29
dot11 ssid WLAN_voice
vlan 14
authentication open
authentication key-management wpa
mbssid guest-mode
wpa-psk ascii 7 080F49592A1500203B2D25567A7A7622263C0C
dot11 ssid Webguest
vlan 5
authentication open
mbssid guest-mode
dot11 wpa handshake timeout 1000
dot11 arp-cache
dot11 priority-map avvid
dot11 phone
power inline negotiation prestandard source
class-map match-all _class_voice0
match ip dscp ef
class-map match-all _class_voice1
match ip dscp cs3
policy-map voice
class _class_voice0
set cos 6
class _class_voice1
set cos 3
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
encryption vlan 11 mode ciphers aes-ccm
encryption vlan 14 mode ciphers aes-ccm
ssid WLAN_data
ssid WLAN_voice
ssid Webguest
mbssid
power client 17
channel 2472
station-role root
dot11 qos class voice local
admission-control
admit-traffic narrowband max-channel 75 roam-channel 6
dot11 qos class voice cell
admission-control
no cdp enable
infrastructure-client
interface Dot11Radio0.5
encapsulation dot1Q 5
no ip route-cache
no cdp enable
bridge-group 5
bridge-group 5 subscriber-loop-control
bridge-group 5 block-unknown-source
no bridge-group 5 source-learning
no bridge-group 5 unicast-flooding
bridge-group 5 spanning-disabled
interface Dot11Radio0.11
encapsulation dot1Q 11
no ip route-cache
no cdp enable
bridge-group 11
bridge-group 11 subscriber-loop-control
bridge-group 11 block-unknown-source
no bridge-group 11 source-learning
no bridge-group 11 unicast-flooding
bridge-group 11 spanning-disabled
interface Dot11Radio0.14
encapsulation dot1Q 14
no ip route-cache
no cdp enable
bridge-group 14
bridge-group 14 subscriber-loop-control
bridge-group 14 block-unknown-source
no bridge-group 14 source-learning
no bridge-group 14 unicast-flooding
bridge-group 14 spanning-disabled
interface Dot11Radio1
no ip address
no ip route-cache
encryption vlan 11 mode ciphers aes-ccm
encryption vlan 14 mode ciphers aes-ccm
ssid WLAN_data
ssid WLAN_voice
ssid Webguest
no dfs band block
mbssid
channel dfs
station-role root
interface Dot11Radio1.5
encapsulation dot1Q 5
no ip route-cache
no cdp enable
bridge-group 5
bridge-group 5 subscriber-loop-control
bridge-group 5 block-unknown-source
no bridge-group 5 source-learning
no bridge-group 5 unicast-flooding
bridge-group 5 spanning-disabled
interface Dot11Radio1.11
encapsulation dot1Q 11
no ip route-cache
no cdp enable
bridge-group 11
bridge-group 11 subscriber-loop-control
bridge-group 11 block-unknown-source
no bridge-group 11 source-learning
no bridge-group 11 unicast-flooding
bridge-group 11 spanning-disabled
interface Dot11Radio1.14
encapsulation dot1Q 14
no ip route-cache
no cdp enable
bridge-group 14
bridge-group 14 subscriber-loop-control
bridge-group 14 block-unknown-source
no bridge-group 14 source-learning
no bridge-group 14 unicast-flooding
bridge-group 14 spanning-disabled
interface FastEthernet0
no ip address
no ip route-cache
speed 100
full-duplex
no cdp enable
hold-queue 160 in
interface FastEthernet0.1
encapsulation dot1Q 1 native
no ip route-cache
no cdp enable
bridge-group 1
no bridge-group 1 source-learning
bridge-group 1 spanning-disabled
interface FastEthernet0.5
encapsulation dot1Q 5
no ip route-cache
no cdp enable
bridge-group 5
no bridge-group 5 source-learning
bridge-group 5 spanning-disabled
interface FastEthernet0.11
encapsulation dot1Q 11
no ip route-cache
no cdp enable
bridge-group 11
no bridge-group 11 source-learning
bridge-group 11 spanning-disabled
interface FastEthernet0.14
encapsulation dot1Q 14
no ip route-cache
no cdp enable
bridge-group 14
no bridge-group 14 source-learning
bridge-group 14 spanning-disabled
service-policy input voice
service-policy output voice
interface BVI1
ip address 10.17.10.5 255.255.255.0
no ip route-cache
ip default-gateway 10.17.10.254
ip http server
ip http authentication aaa
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
logging trap warnings
logging 10.15.51.115
no cdp run
bridge 1 route ip
line con 0
line vty 0 4
sntp server 10.15.1.50
sntp broadcast client
end
Does someone ever experienced a similar problem ?
When I shut radio interfaces they're is no more problems on the LAN. Can this be an overlapping coverage issue ?
Can someone please give me advices on how to troubleshoot this issue ?
Thank you in advance as I'm a bit stuck.
Best Regards,Hi Scott,
Thanks for your reply.
Do you think this can be the origin of the issue my customer encounters or is it only to be standard ? As this change will have to be made on all clients, if there is a chance it solves the problem I will do it ASAP, if not I will delay it in a less busy period :-)
Can the constant roaming associations and dissasociations overload the AP and make it stop responding on the LAN or is it only a throuhput problem ?
Thanks in advance for your answer.
Best Regards, -
AIR-AP1142N-A-K9 configuration issue for guest ssid
I'm trying to get the guest ssid working. I was frustrated so saved my old config and wiped out everything on this AP. Now my bvi1 does not come online.
ap#sh ip int bri
Interface IP-Address OK? Method Status Protocol
BVI1 192.168.2.249 YES NVRAM down down
Dot11Radio0 unassigned YES NVRAM up up
Dot11Radio0.50 unassigned YES unset up up
Dot11Radio0.51 unassigned YES unset up up
Dot11Radio1 unassigned YES NVRAM administratively down down
GigabitEthernet0 unassigned YES NVRAM up up
GigabitEthernet0.50 unassigned YES unset up up
GigabitEthernet0.51 unassigned YES unset up up
ap#
ap#sh int bvi
*May 6 15:05:24.611: %DOT11-6-ASSOC: Interface Dot11Radio0, Station 847a.8835.4f22 Associated KEY_MGMT[WPAv2 PSK]1
BVI1 is down, line protocol is down
Hardware is BVI, address is 003a.99eb.8d00 (bia b862.1fe9.9af0)
Internet address is 192.168.2.249/24
MTU 1500 bytes, BW 54000 Kbit, DLY 5000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
ARP type: ARPA, ARP Timeout 04:00:00
Last input never, output never, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
3 packets output, 180 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 unknown protocol drops
0 output buffer failures, 0 output buffers swapped out
ap#
I have a private vlan 50 and the public vlan 51. The private ssid seems to work and allow connectivity to the internet but I don't understand with the same configuration the Public ssid doesn't seem to work.
I get this output when trying to connect with my cell phone.
*May 6 15:00:37.288: %DOT11-6-DISASSOC: Interface Dot11Radio0, Deauthenticating Station 847a.8835.4f22 Reason: Sending station has left the BSS
*May 6 15:00:38.432: %DOT11-6-ASSOC: Interface Dot11Radio0, Station TYLOR-NB 9c4e.3617.483c Reassociated KEY_MGMT[WPAv2 PSK]
*May 6 15:00:42.935: %DOT11-6-ASSOC: Interface Dot11Radio0, Station 847a.8835.4f22 Associated KEY_MGMT[WPAv2 PSK]
*May 6 15:00:54.320: %DOT11-6-ASSOC: Interface Dot11Radio0, Station 2c44.01c3.70a6 Associated KEY_MGMT[WPAv2 PSK]
*May 6 15:01:13.913: %DOT11-6-DISASSOC: Interface Dot11Radio0, Deauthenticating Station 847a.8835.4f22 Reason: Sending station has left the BSS
*May 6 15:01:17.281: %DOT11-6-ASSOC: Interface Dot11Radio0, Station 847a.8835.4f22 Associated KEY_MGMT[WPAv2 PSK]
*May 6 15:01:48.181: %DOT11-6-DISASSOC: Interface Dot11Radio0, Deauthenticating Station 847a.8835.4f22 Reason: Sending station has left the BSS
*May 6 15:01:51.583: %DOT11-6-ASSOC: Interface Dot11Radio0, Station 847a.8835.4f22 Associated KEY_MGMT[WPAv2 PSK]
*May 6 15:02:22.500: %DOT11-6-DISASSOC: Interface Dot11Radio0, Deauthenticating Station 847a.8835.4f22 Reason: Sending station has left the BSS
*May 6 15:03:41.852: %DOT11-6-ASSOC: Interface Dot11Radio0, Station 847a.8835.4f22 Associated KEY_MGMT[WPAv2 PSK]
SSID [PUBLIC] :
MAC Address IP address Device Name Parent State
847a.8835.4f22 0.0.0.0 ccx-client - self Assoc
ap#
ap#show run
Building configuration...
Current configuration : 2746 bytes
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname ap
enable secret 5 $1$4jEJ$ajpjBvSx3DUhxyvLADj.91
aaa new-model
aaa authentication login default local
aaa authorization exec default local
aaa session-id common
dot11 syslog
dot11 ssid PRIVATE
vlan 50
authentication open
authentication key-management wpa version 2
mbssid guest-mode
wpa-psk ascii 7 01150F035E050E0A2D
dot11 ssid PUBLIC
vlan 51
authentication open
authentication key-management wpa version 2
mbssid guest-mode
wpa-psk ascii 7 045D02010A2F444B05
username Admin privilege 15 password 7 0526071D3545175840
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
encryption vlan 50 mode ciphers aes-ccm
encryption vlan 51 mode ciphers aes-ccm
encryption mode ciphers aes-ccm tkip
ssid PRIVATE
ssid PUBLIC
antenna gain 0
mbssid
station-role root
interface Dot11Radio0.50
encapsulation dot1Q 50 native
no ip route-cache
bridge-group 50
bridge-group 50 subscriber-loop-control
bridge-group 50 block-unknown-source
no bridge-group 50 source-learning
no bridge-group 50 unicast-flooding
bridge-group 50 spanning-disabled
interface Dot11Radio0.51
encapsulation dot1Q 51
no ip route-cache
bridge-group 51
bridge-group 51 subscriber-loop-control
bridge-group 51 block-unknown-source
no bridge-group 51 source-learning
no bridge-group 51 unicast-flooding
bridge-group 51 spanning-disabled
interface Dot11Radio1
no ip address
no ip route-cache
shutdown
antenna gain 0
dfs band 3 block
channel dfs
station-role root
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface GigabitEthernet0
no ip address
no ip route-cache
duplex auto
speed auto
no keepalive
interface GigabitEthernet0.50
encapsulation dot1Q 50 native
no ip route-cache
bridge-group 50
no bridge-group 50 source-learning
bridge-group 50 spanning-disabled
interface GigabitEthernet0.51
encapsulation dot1Q 51
no ip route-cache
bridge-group 51
no bridge-group 51 source-learning
bridge-group 51 spanning-disabled
interface BVI1
ip address 192.168.2.249 255.255.255.0
no ip route-cache
ip default-gateway 192.168.2.1
ip http server
ip http authentication aaa
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
bridge 1 route ip
line con 0
line vty 0 4
end
switch config:
interface FastEthernet1/0/46
switchport trunk encapsulation dot1q
switchport trunk native vlan 50
switchport trunk allowed vlan 50,51
switchport mode trunkHi
I know the bridge-group have to be identical to the sub interface number and vlan number
This is true for all other vlans except for native vlan. For native vlan sub-interfaces bridge group number always should be 1. In your case, if vlan 50 is the native vlan (192.168.2.x/24 belong vlan) then configure bridge-group 1 under those .50 sub-interfaces. Then everything should work :)
It is ideal if you could put AP management (BVI IP) into separate vlan & two user groups put vlan 50 & 51. Here is a sample configuration where vlan 110 is Mgmt & vlan 12,13 for user vlans.
http://mrncciew.com/2012/10/24/multiple-ssid-config-on-autonomous-ap/
HTH
Rasika
**** Pls rate all useful responses **** -
All of my 3560 ports connected to phones (7940/42/60/70/71) are showing continuous 50pps output towards the phones. I've turned off GARP but still no improvement.
Although most of these phones have PC's attached, the data VLAN is not affected.
I can't get an ethereal until tomorrow but on the off chance anyone has seen this before ?
Here's a sh int from an affected interface :-
FastEthernet0/7 is up, line protocol is up (connected)
Hardware is Fast Ethernet, address is 001d.e516.6109 (bia 001d.e516.6109)
MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Full-duplex, 100Mb/s, media type is 10/100BaseTX
input flow-control is off, output flow-control is unsupported
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:00:50, output 00:00:00, output hang never
Last clearing of "show interface" counters 00:00:01
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 90000 bits/sec, 51 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts (0 multicasts)
0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 watchdog, 0 multicast, 0 pause input
0 input packets with dribble condition detected
104 packets output, 22640 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier, 0 PAUSE output
Appreciate any ideas.
TIA.Hi,
I had the similar problem like you now.
The problem was in Microsoft Load Balansing.
The Microsoft guys have tried to do load balansing but it didn't work and there was a lot of multicat packets in that VLAN.
After we have removed these servers, everything was OK.
Maybe this can help you?
Regards,
Vlaho -
Setting up Multiple SSID's & VLAN
I have a Cisco 1230 AP along with a Sonic Wall TZ 210 and a Linksys SFE 2010P switch. On my AP I have created 2 SSID's. and 2 VLAN's. The first SSID is being broadcasted and has WPA encryption on it for our Corporate USers. The Second SSID is a Guest SSID and too is being broadcasted. I can make a laptop connect to the 1st SSID, but for some reason the 2nd SSID nothing will connect to it. The first SSID is associated to VLAN1 and the 2nd SSID is associated to VLAN2. VLAN1 has WPA encryption on it. VLAN2 is setup as Open and no Encryption. Any ideas?
My next question is how to I configure traffic on this AP with the other equipment mentioned? On my sonicwall we have segmented port6 on it to be a different subnet from the corporate subnet. On the Linksys switch I have enable VLANS on port2 and port48 which are on VLAN2. All other ports are on VLAN1. The AP connects to Ports 2 on the linksys switch and port 48 connects to port 6 on the Sonic Wall. When a corporate user connects to SSID1 I want them to be able to connect to the Corporate subnet. When a guest connects to SSID2 I want them to connect to the segmented guest network to only have Internet Access.
Hope this makes sense!
Below is my config on the AP. I am really only familiar with the IOS web interface so if you can explain it using that I'd appreciate it.
AP_WLAN_Bakery
Home Exec Configure
------------------ show version ------------------
Cisco IOS Software, C1200 Software (C1200-K9W7-M), Version 12.3(8)JEB1, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2007 by Cisco Systems, Inc.
Compiled Fri 20-Jul-07 20:51 by dchih
ROM: Bootstrap program is C1200 boot loader
BOOTLDR: C1200 Boot Loader (C1200-BOOT-M) Version 12.2(8)JA, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)
AP_WLAN_Bakery uptime is 1 hour, 40 minutes
System returned to ROM by reload
System restarted at 10:52:05 -0400 Fri Oct 15 2010
System image file is "flash:/c1200-k9w7-mx.123-8.JEB1/c1200-k9w7-mx.123-8.JEB1"
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
cisco AIR-AP1231G-A-K9 (PowerPC405GP) processor (revision B0) with 15138K/1236K bytes of memory.
Processor board ID FOC0849218B
PowerPC405GP CPU at 196Mhz, revision number 0x0145
Last reset from reload
1 FastEthernet interface
1 802.11 Radio(s)
32K bytes of flash-simulated non-volatile configuration memory.
Base ethernet MAC Address: 00:12:D9:8B:09:93
Part Number : 73-8704-08
PCA Assembly Number : 800-23211-09
PCA Revision Number : A0
PCB Serial Number : FOC0849218B
Top Assembly Part Number : 800-23304-08
Top Assembly Serial Number : FTX0902R2V1
Top Revision Number : A0
Product/Model Number : AIR-AP1231G-A-K9
Configuration register is 0xF
------------------ show running-config ------------------
Building configuration...
Current configuration : 2544 bytes
! Last configuration change at 12:07:29 -0400 Fri Oct 15 2010 by admin
! NVRAM config last updated at 12:07:29 -0400 Fri Oct 15 2010 by admin
version 12.3
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname AP_WLAN_Bakery
clock timezone -0500 -5
clock summer-time -0400 recurring
ip subnet-zero
aaa new-model
aaa authentication login default local
aaa authorization exec default local
aaa session-id common
dot11 vlan-name VLAN_Corporate vlan 1
dot11 vlan-name VLAN_Guest vlan 2
dot11 ssid WLAN_Corporate
vlan 1
authentication open
authentication key-management wpa
mbssid guest-mode
wpa-psk ascii 7 005740565C0C5C5F5C741F
dot11 ssid WLAN_HartKitGuest
vlan 2
authentication open
mbssid guest-mode
username admin privilege 15 password 7 <removed>
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
encryption mode ciphers aes-ccm tkip
encryption vlan 1 mode ciphers aes-ccm tkip
ssid WLAN_Corporate
ssid WLAN_HartKitGuest
mbssid
speed basic-6.0 basic-9.0 basic-12.0 basic-18.0 basic-24.0 basic-36.0 basic-48.0 basic-54.0
station-role root
no dot11 extension aironet
interface Dot11Radio0.1
encapsulation dot1Q 1 native
no ip route-cache
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface Dot11Radio0.2
encapsulation dot1Q 2
no ip route-cache
bridge-group 2
bridge-group 2 subscriber-loop-control
bridge-group 2 block-unknown-source
no bridge-group 2 source-learning
no bridge-group 2 unicast-flooding
bridge-group 2 spanning-disabled
interface FastEthernet0
no ip address
no ip route-cache
duplex auto
speed auto
interface FastEthernet0.1
encapsulation dot1Q 1 native
no ip route-cache
bridge-group 1
no bridge-group 1 source-learning
bridge-group 1 spanning-disabled
interface FastEthernet0.2
encapsulation dot1Q 2
no ip route-cache
bridge-group 2
no bridge-group 2 source-learning
bridge-group 2 spanning-disabled
interface BVI1
ip address 192.168.2.240 255.255.255.0
no ip route-cache
ip default-gateway 192.168.2.1
ip http server
ip http authentication aaa
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
bridge 1 route ip
line con 0
line vty 0 4
sntp server 192.168.2.5
sntp broadcast client
end
------------------ show stacks ------------------
Minimum process stacks:
Free/Size Name
4572/5500 soap_flash init
10024/11000 DHCP Autoinstall
5160/5500 Autoinstall
11748/12000 Setup
10552/11000 BootP Resolver
5240/5500 dot11 platform init
8824/12000 Init
5088/5500 RADIUS INITCONFIG
2576/3000 Rom Random Update Process
5144/11000 HTTP CP
3084/5500 Soap Flash Save Variables
Interrupt level stacks:
Level Called Unused/Size Name
4 125707 8056/9000 dot11 radio interrupt
6 9783 8960/9000 NS16550 VECTOR
------------------ show interfaces ------------------
BVI1 is up, line protocol is up
Hardware is BVI, address is 0012.d98b.0993 (bia 0013.1973.8d50)
Internet address is 192.168.2.240/24
MTU 1500 bytes, BW 54000 Kbit, DLY 5000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
ARP type: ARPA, ARP Timeout 04:00:00
Last input never, output never, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
5 minute input rate 10000 bits/sec, 9 packets/sec
5 minute output rate 10000 bits/sec, 4 packets/sec
59436 packets input, 8310033 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
31826 packets output, 18823451 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 output buffer failures, 0 output buffers swapped out
Dot11Radio0 is up, line protocol is up
Hardware is 802.11G Radio, address is 0013.1973.8d50 (bia 0013.1973.8d50)
MTU 1500 bytes, BW 54000 Kbit, DLY 1000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:15:20, output 00:15:20, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 47
Queueing strategy: fifo
Output queue: 0/30 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
16093 packets input, 1696312 bytes, 0 no buffer
Received 1913 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 input packets with dribble condition detected
8367 packets output, 2930004 bytes, 0 underruns
13 output errors, 0 collisions, 37 interface resets
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier
0 output buffer failures, 0 output buffers swapped out
Dot11Radio0.1 is up, line protocol is up
Hardware is 802.11G Radio, address is 0013.1973.8d50 (bia 0013.1973.8d50)
MTU 1500 bytes, BW 54000 Kbit, DLY 1000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation 802.1Q Virtual LAN, Vlan ID 1.
ARP type: ARPA, ARP Timeout 04:00:00
Last clearing of "show interface" counters never
Dot11Radio0.2 is up, line protocol is up
Hardware is 802.11G Radio, address is 0013.1973.8d50 (bia 0013.1973.8d50)
MTU 1500 bytes, BW 54000 Kbit, DLY 1000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation 802.1Q Virtual LAN, Vlan ID 2.
ARP type: ARPA, ARP Timeout 04:00:00
Last clearing of "show interface" counters never
FastEthernet0 is up, line protocol is up
Hardware is PowerPC405GP Ethernet, address is 0012.d98b.0993 (bia 0012.d98b.0993)
MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Full-duplex, 100Mb/s, MII
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:00:00, output 00:00:00, output hang never
Last clearing of "show interface" counters never
Input queue: 0/160/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 13000 bits/sec, 10 packets/sec
5 minute output rate 10000 bits/sec, 4 packets/sec
75878 packets input, 12726627 bytes
Received 43517 broadcasts, 0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 watchdog
0 input packets with dribble condition detected
38986 packets output, 19917202 bytes, 0 underruns
0 output errors, 0 collisions, 7 interface resets
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier
0 output buffer failures, 0 output buffers swapped out
FastEthernet0.1 is up, line protocol is up
Hardware is PowerPC405GP Ethernet, address is 0012.d98b.0993 (bia 0012.d98b.0993)
MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation 802.1Q Virtual LAN, Vlan ID 1.
ARP type: ARPA, ARP Timeout 04:00:00
Last clearing of "show interface" counters never
FastEthernet0.2 is up, line protocol is up
Hardware is PowerPC405GP Ethernet, address is 0012.d98b.0993 (bia 0012.d98b.0993)
MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation 802.1Q Virtual LAN, Vlan ID 2.
ARP type: ARPA, ARP Timeout 04:00:00
Last clearing of "show interface" counters never
------------------ show controllers ------------------
interface Dot11Radio0
Radio AIR-MP31G, Base Address 0013.1973.8d50, BBlock version 0.00, Software version 6.11.1
Serial number: FOC0901D4S1
Number of supported simultaneous BSSID on Dot11Radio0: 8
Carrier Set: Americas (US )
Uniform Spreading Required: No
Current Frequency: 2412 MHz Channel 1
Allowed Frequencies: 2412(1) 2417(2) 2422(3) 2427(4) 2432(5) 2437(6) 2442(7) 2447(8) 2452(9) 2457(10) 2462(11)
Listen Frequencies: 2412(1) 2417(2) 2422(3) 2427(4) 2432(5) 2437(6) 2442(7) 2447(8) 2452(9) 2457(10) 2462(11) 2467(12) 2472(13) 2484(14)
Beacon Flags: 0; Beacons are enabled; Probes are enabled
Current CCK Power: 100 mW
Allowed CCK Power Levels: 1 5 10 20 30 50 100
Current OFDM Power: 30 mW
Allowed OFDM Power Levels: 1 5 10 20 30
Allowed Client Power Levels: 1 5 10 20 30 50 100
ERP settings: short slot time.
Neighbors in non-erp mode:
Current Rates: basic-6.0 basic-9.0 basic-12.0 basic-18.0 basic-24.0 basic-36.0 basic-48.0 basic-54.0
Active Rates: basic-6.0 basic-9.0 basic-12.0 basic-18.0 basic-24.0 basic-36.0 basic-48.0 basic-54.0
Allowed Rates: 1.0 2.0 5.5 6.0 9.0 11.0 12.0 18.0 24.0 36.0 48.0 54.0
Best Range Rates: basic-1.0 2.0 5.5 6.0 9.0 11.0 12.0 18.0 24.0 36.0 48.0 54.0
Best Throughput Rates: basic-1.0 basic-2.0 basic-5.5 basic-6.0 basic-9.0 basic-11.0 basic-12.0 basic-18.0 basic-24.0 basic-36.0 basic-48.0 basic-54.0
Default Rates: basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0 54.0
Current Voice Rates: 5.5 6.0 11.0 12.0 24.0 [disabled until voice packet-discard enabled]
Default Voice Rates: 5.5 6.0 11.0 12.0 24.0
Channel / Max Power Table
1 O=15 D=20, 2 O=15 D=20, 3 O=15 D=20, 4 O=15 D=20, 5 O=15 D=20
6 O=15 D=20, 7 O=15 D=20, 8 O=15 D=20, 9 O=15 D=20, 10 O=15 D=20
11 O=15 D=20
Data Rate Sensitivity (rate, SNR dB, Contention dBm)
( 1.0, 1, -98) ( 2.0, 7, -94) ( 5.5, 9, -92) (11.0, 16, -86)
( 6.0, 7, -92) ( 9.0, 14, -87) (12.0, 12, -87) (18.0, 15, -84)
(24.0, 17, -82) (36.0, 24, -76) (48.0, 29, -73) (54.0, 33, -69)
Radio Management (RM) Configuration:
Regular AP RM Mode 1 Temp Setting Disabled
Temp Settings: AP Tx Power 0 AP Tx Channel 0 Client Tx Power 0
Rates:
Saved Settings: AP Tx Power 0 AP Tx Channel 1 Client Tx Power 0
Rates:
MCST RSCs: [0]0x0 [1]0x0 [2]0x0 [3]0x0 [4]0x0
TKIP Cum Stats: STA MIC-L-Errs MIC-R-Errs Replay C-Measure
0000.0000.0000 00000000 00000000 00000000 00000000
AES-CCMP Cum Stats: 00000000 replays discarded
QBSS Load: 0x0
Policing Stats:Rx downgardes 0, Tx downgrades 0
Configured Local Access Class Parameters
Back : cw-min 4 cw-max 10 fixed-slot 7 admission-control Off txop 0
Best : cw-min 4 cw-max 6 fixed-slot 3 admission-control Off txop 0
Video : cw-min 3 cw-max 4 fixed-slot 1 admission-control Off txop 3008
Voice : cw-min 2 cw-max 3 fixed-slot 1 admission-control Off txop 1504
Configured Cell Access Class Parameters
Back : cw-min 4 cw-max 10 fixed-slot 7 admission-control Off txop 0
Best : cw-min 4 cw-max 10 fixed-slot 3 admission-control Off txop 0
Video : cw-min 3 cw-max 4 fixed-slot 2 admission-control Off txop 3008
Voice : cw-min 2 cw-max 3 fixed-slot 2 admission-control Off txop 1504
Transmit queues: Active 0 In Progress 0
---- Active --- In-Progress --------------- Counts --------------
Cnt Quo Bas Max Cnt Quo Bas Sent Discard Fail Retry Multi
Uplink 0 0 0 0 0 0 0 0 0 0 0 0
Voice 0 0 0 0 0 0 0 55 0 0 1 1
Video 0 0 0 0 0 0 0 0 0 0 0 0
Best 0 3 70 3 0 3 24 7937 0 0 127 12
Mcast 0 0 0 0 0 0 0 329 0 0 0 0
Mcast 0 0 0 0 0 0 0 30 0 0 0 0
Back 0 0 0 0 0 0 0 329 0 0 0 0
BSSIDS Index Flags State Next Held Defer NonDefer Clients Tsf Dtim Txq
8D50 0 20 0 0 0 0 0 0 200 2 0
8D51 1 20 0 0 0 0 0 0 150 2 1
UP ClientQAged AcQAged PacketAged Drop Retry/Thresh Timeout CQMax
7 0 0 0 3/100 0/500 35 4
6 0 0 0 3/100 0/500 35 4
5 0 0 0 3/100 0/500 35 4
4 0 0 0 3/100 0/500 35 4
3 0 0 0 3/100 0/500 35 4
2 0 0 0 3/100 0/500 35 4
1 0 0 0 3/100 0/500 35 4
Driver TX blocks: in use 0, high 10, at reset 0, fail 0, reclaim 0
Clients: 8021x auth in prog 0 allowed 0
Vlan BSSID Clients PSP Pri Encr Key0 Key1 Key2 Key3 SSIDs
0 8D50 0 0 0 0 234 x128
1n 8D50 0 0 0 0 234 x128 WLAN_Corporate
2 8D51 1 0 0 0 0 WLAN_HartKitGuest
0 0 flags 3
1 1 flags 3
0 0 flags 0
0 0 flags 0
0 0 flags 0
0 0 flags 0
0 0 flags 0
0 0 flags 0
0 0 flags 0
0 0 flags 0
0 0 flags 0
0 0 flags 0
0 0 flags 0
0 0 flags 0
0 0 flags 0
0 0 flags 0
0 0 flags 0
17 0 flags 0
18 0 flags 0
Registers: io E8000000 mem 80000000 aux A0000000
0000 FF50 0000 0000 0021 0000 0000 0000
0001 0000 0000 0000 0000 0000 0000 0000
0000 0000 0000 0000 0000 0000 0000 0000
0500 0007 0000 0000 0808 09E8 0000 0504
0000 0000 0000 0000 0424 0059 E2ED 2D9D
00000000 00000200 20000200 FFFFFFFF F7FFFFFF 00000000 00000000 00200000
FFFFFFE2 00000FFF 72ED14BD 4A040401 00000000 00000000 00008000 00008080
00000000 00000000 00000000 00000000 00008F78 000012DC 00000000 0000C0EA
Radio running: temp 0 C tx_power 100 bb_code 0x0
rssi_threshold 0x0 gain offset 0
Antenna: external , gain 20 (platform 0, domain class A)
PCI sys_id: 0xA506 subsys_id 0x5100 (0x5101)
Unicast ciphers 0x1 mcast ciphers 0x1
Rid Ring:
A0000970: 009C8000 20ED1EA0 * n
Rx Ring:
A0000950: 893E0002 20ED3478 v, 893E0002 20EDEE60 v
A0000960: 893E0002 20EE4B54 v, 893E0002 20EDB068 * v
Tx Ring:
A0000800: 06108000 20ECFCE4 n, 009A8000 20ECD764 n
A0000810: 00AE8000 20ECF064 n, 010C8000 20ECD124 n
A0000820: 010C8000 20ECCE04 n, 010C8000 20ECE0C4 n
A0000830: 010C8000 20ECED44 n, 00668000 20ECB174 n
A0000840: 006A8000 20ECCA64 n, 010C8000 20ECDDA4 n
A0000850: 010C8000 20ECF6A4 n, 01848000 20ECF9C4 n
A0000860: 022A8000 20ECCE04 n, 01848000 20ECF9C4 n
A0000870: 06158000 20ED113C n, 01848000 20ECE3E4 n
A0000880: 022A8000 20ECF064 * n, 01188000 20ECD124 n
A0000890: 05688000 20ED0A74 n, 057C8000 20ED03AC n
A00008A0: 010C8000 20ECED44 n, 010C8000 20ECDDA4 n
A00008B0: 010C8000 20ECF6A4 n, 010C8000 20ECF9C4 n
A00008C0: 00748000 20ECB054 n, 05FC8000 20ED1804 n
TxDn Ring:
A0000930: 802C0000 20ED26A0 v, 802C0000 20ED2778 v
A0000940: 802C0000 20ED2850 * v, 802C0000 20ED2928 v
Multicast counters:
Internal MC counts:
28 (28) 0 (0) 0 (0) 0 (0) 0 (0) 0 (0) 0 (0) 0 (0) 0 (0) 0 (0) 0 (0) 0 (0) 0 (0) 0 (0) 0 (0) 0 (0)
Log Buffer:
PowerPC405GP Ethernet unit 0
PHY Hardware is Intel LXT971 rev. 2 (id_register: 0x13, 0x78E2)
rx_intr: 0 tx_intr: 0 mac_err_isr: 0 phy_link_isr:0
Current station address 0012.d98b.0993, default address 0012.d98b.0993
MAL register dump:
malcr 0x0007C082 0x180
malesr 0x00000000 0x181
malier 0x0000000F 0x182
maltxcasr 0x80000000 0x184
maltxcarr 0x80000000 0x185
maltxeobisr 0x00000000 0x186
maltxdeir 0x00000000 0x187
malrxcasr 0x80000000 0x190
malrxcarr 0x80000000 0x191
malrxeobisr 0x00000000 0x192
malrxdeir 0x00000000 0x193
maltxctp0r 0x00EE6120 0x1A0
malrxctp0r 0x00EE6020 0x1C0
malrcbs0 0x00000060 0x1E0
EMAC register dump:
emacmr0 0x18000000 0x00
emacmr1 0xA1788000 0x04
emactmr0 0x00000000 0x08
emactmr1 0x380F0000 0x0C
emacrmr 0x7D180000 0x10
emacisr 0x00000002 0x14
emacier 0x00000001 0x18
emaciah 0x00000012 0x1C
emacial 0xD98B0993 0x20
emacptr 0x0000FFFF 0x2C
emaclsah 0x00000040 0x50
emaclsal 0x2B637E9B 0x54
emacipgr 0x00000004 0x58
emacstacr 0x47808011 0x5C
emactrtr 0x18000000 0x60
emacrwmr 0x0F002000 0x64
emacoctx 0x0132EA47 0x68
emacocrx 0x00C72D8B 0x6C
UIC register dump:
uicsr 0x00001FA3 0xC0
uicer 0x803F0048 0xC2
uicmsr 0x00000000 0xC6
PHY register dump:
3100 782D 0013 78E2 01E1 41E1 0007 2001 0000 0000 0000 0000 0000 0000 0000 0000
0384 4780 0032 0000 0422 0000 0000 0000 0000 0000 08C8 0000 0000 0000 0000
RX ring with 16 entries at 0xEE6020, Buffer size 1528
Rxhead = 0xEE6048 (5), Rxp = 0xB67360 (5)
00 pak=0x0B6D644 buf=0x0EF2BDC status=9C00 pak_size=0
01 pak=0x0B6CCA8 buf=0x0EF17A8 status=9C00 pak_size=0
02 pak=0x0B68C98 buf=0x0EE90F8 status=9C00 pak_size=0
03 pak=0x0B6BCA4 buf=0x0EEF5FC status=9C00 pak_size=0
04 pak=0x0B6DFE0 buf=0x0EF4010 status=9C00 pak_size=0
05 pak=0x0B6CFDC buf=0x0EF1E64 status=9C00 pak_size=0
06 pak=0x0B6C640 buf=0x0EF0A30 status=9C00 pak_size=0
07 pak=0x0B682FC buf=0x0EE7CC4 status=9C00 pak_size=0
08 pak=0x0B6E648 buf=0x0EF4D88 status=9C00 pak_size=0
09 pak=0x0B6E97C buf=0x0EF5444 status=9C00 pak_size=0
10 pak=0x0B6ECB0 buf=0x0EF5B00 status=9C00 pak_size=0
11 pak=0x0B6ACA0 buf=0x0EED450 status=9C00 pak_size=0
12 pak=0x0B68630 buf=0x0EE8380 status=9C00 pak_size=0
13 pak=0x0B6D310 buf=0x0EF2520 status=9C00 pak_size=0
14 pak=0x0B6C974 buf=0x0EF10EC status=9C00 pak_size=0
15 pak=0x0B6B63C buf=0x0EEE884 status=DC00 pak_size=0
TX ring with 8 entries at 0xEE6120, tx_count = 0
tx_head = 0xEE6148 (5), head_txp = 0xB673BC (5)
tx_tail = 0xEE6148 (5), tail_txp = 0xB673BC (5)
00 pak=0x0000000 buf=0x0000000 status=1400 pak_size=0
01 pak=0x0000000 buf=0x0000000 status=1400 pak_size=0
02 pak=0x0000000 buf=0x0000000 status=1400 pak_size=0
03 pak=0x0000000 buf=0x0000000 status=1400 pak_size=0
04 pak=0x0000000 buf=0x0000000 status=1400 pak_size=0
05 pak=0x0000000 buf=0x0000000 status=1400 pak_size=0
06 pak=0x0000000 buf=0x0000000 status=1400 pak_size=0
07 pak=0x0000000 buf=0x0000000 status=5400 pak_size=0
0 missed datagrams, 0 overruns
0 transmitter underruns, 0 excessive collisions
0 single collisions, 0 multiple collisions
0 dma memory errors, 0 CRC errors
0 alignment errors, 0 runts, 0 giants
emac/mal specific errors:
0 rx in range, 0 rx out range
0 mal_rx_serr, 0 mal_tx_serr
0 mal_rx_de, 0 mal_tx_de
0 emac_int
0 mal_err_isr
0 SQE errors, 0 tx CRC errors
0 output queue fail
------------------ show data-corruption ------------------
No data inconsistency errors have been recorded.
------------------ show file systems ------------------
File Systems:
Size(b) Free(b) Type Flags Prefixes
* 7741440 2734080 flash rw flash:
- - opaque rw bs:
7741440 2734080 unknown rw zflash:
- - opaque rw archive:
- - opaque rw system:
32768 29138 nvram rw nvram:
- - network rw tftp:
- - opaque rw null:
- - opaque ro xmodem:
- - opaque ro ymodem:
- - network rw rcp:
- - network rw ftp:
- - network rw http:
- - network rw scp:
- - network rw https:
------------------ show flash: ------------------
Directory of flash:/
2 -rwx 1048 Oct 15 2010 12:07:29 -04:00 private-multiple-fs
5 drwx 512 Oct 15 2010 10:36:30 -04:00 c1200-k9w7-mx.123-8.JEB1
4 -rwx 716 Feb 28 2002 19:06:22 -05:00 env_vars
146 -rwx 2549 Oct 15 2010 12:07:29 -04:00 config.txt
148 -rwx 5 Oct 15 2010 12:07:29 -04:00 private-config
7741440 bytes total (2734080 bytes free)
------------------ dir nvram: ------------------
Directory of nvram:/
30 -rw- 2549 <no date> startup-config
31 ---- 5 <no date> private-config
1 -rw- 0 <no date> ifIndex-table
32768 bytes total (29138 bytes free)
------------------ show memory statistics ------------------
Head Total(b) Used(b) Free(b) Lowest(b) Largest(b)
Processor A4AB84 4709500 2431436 2278064 1920552 2125904
I/O ECB000 1265664 468008 797656 727168 779580
------------------ show process memory ------------------
Total: 5975164, Used: 2899444, Free: 3075720
PID TTY Allocated Freed Holding Getbufs Retbufs Process
0 0 3373064 827724 1898920 0 0 *Init*
0 0 11804 7372856 11804 0 0 *Sched*
0 0 66125428 65999528 293168 434276 0 *Dead*
1 0 0 0 6416 0 0 Chunk Manager
2 0 188 188 3916 0 0 Load Meter
3 0 448120 443220 18392 0 0 HTTP CP
4 0 19548 0 25964 0 0 Check heaps
5 0 86364 207192 37368 49920 137052 Pool Manager
6 0 0 0 6416 0 0 AAA_SERVER_DEADT
7 0 188 188 6416 0 0 Timers
8 0 188 188 6416 0 0 AAA high-capacit
9 0 488 0 6904 0 0 SNTP
10 0 76 0 6492 0 0 ARP Input
11 0 3232 540 9108 0 0 Entity MIB API
12 0 0 0 6416 0 0 HC Counter Timer
13 0 188 188 6416 0 0 GraphIt
14 0 0 0 6416 0 0 Net Input
15 0 0 0 6416 0 0 Critical Bkgnd
16 0 19648 136 12180 0 0 Net Background
17 0 188 188 11916 0 0 Logger
18 0 188 188 6416 0 0 TTY Background
19 0 0 0 9916 0 0 Per-Second Jobs
20 0 188 188 6416 0 0 Compute load avg
21 0 0 0 6416 0 0 Per-minute Jobs
22 0 125880 59144 52956 0 0 Dot11 driver
23 0 188 188 6416 0 0 Dot11 driver log
24 0 0 0 6416 0 0 Voice Metrics Ta
25 0 0 0 6416 0 0 SOAP LED Process
26 0 188 188 6416 0 0 AAA Server
27 0 0 0 6416 0 0 AAA ACCT Proc
28 0 0 0 6416 0 0 ACCT Periodic Pr
29 0 2343100 10891400 16904 0 7173144 IP Input
30 0 0 0 6416 0 0 ICMP event handl
31 0 188 188 6416 0 0 AAA Dictionary R
32 0 47124 44272 9200 0 0 CDP Protocol
33 0 0 0 6416 0 0 linktest
34 0 964 964 9916 0 0 Dot11 aaa proces
35 0 0 0 9916 0 0 pmkid
36 0 188 6404 6416 0 0 Dot11 Mgmt & Ass
37 0 1636 1224 6644 0 0 AiroIAPP Protoco
38 0 188 188 6416 0 0 Triggered events
39 0 188 188 9916 0 0 Dot11 auth Dot1x
40 0 0 0 6416 0 0 Dot11 Mac Auth
41 0 1276 0 7692 0 0 Dot11CACprocess
42 0 0 1285716 11916 0 0 TCP Timer
43 0 0 0 11916 0 0 TCP Protocols
44 0 0 0 6416 0 0 Socket Timers
45 0 41144 11308 23364 0 0 DHCPD Receive
46 0 58666708 40499364 31400 6957504 101520 HTTP CORE
47 0 1072 188 12800 0 0 Soap Upgrade fet
48 0 10608 188 16836 0 0 DDP
49 0 344168 1754412 6416 0 0 LOCAL AAA
50 0 188 188 6416 0 0 AAA Cached Serve
51 0 188 188 6416 0 0 ENABLE AAA
52 0 188 188 6416 0 0 LINE AAA
54 0 2056 188 8284 0 0 TPLUS
55 0 604 188 9332 0 0 Crypto WUI
56 0 0 0 6416 0 0 EM Background Pr
57 0 188 308 6416 0 0 Soap Consoleless
58 0 72384 66968 14332 0 0 Crypto CA
59 0 0 0 8916 0 0 Crypto PKI-CRL
60 0 0 0 8916 0 0 Crypto SSL
61 0 2056 15044 6416 0 0 AAA SEND STOP EV
62 0 188 188 6416 0 0 Dot11 LBS Proc
63 0 0 0 6416 0 0 Syslog Traps
65 0 0 0 6416 0 0 DHCPD Timer
66 0 76 484 9992 0 0 DHCP Client
67 0 636960 188 22156 421308 0 HyBridge Input P
68 0 344 188 6588 0 0 Tbridge Monitor
69 0 344 188 6572 0 0 Spanning Tree
70 0 156 0 6628 0 0 DHCPD Database
2897284 Total
------------------ show process cpu ------------------
CPU utilization for five seconds: 16%/0%; one minute: 4%; five minutes: 1%
PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process
1 0 1 0 0.00% 0.00% 0.00% 0 Chunk Manager
2 4 1196 3 0.00% 0.00% 0.00% 0 Load Meter
3 369 40 9225 0.00% 0.00% 0.00% 0 HTTP CP
4 764 611 1250 0.00% 0.00% 0.00% 0 Check heaps
5 9 44 204 0.00% 0.00% 0.00% 0 Pool Manager
6 0 1 0 0.00% 0.00% 0.00% 0 AAA_SERVER_DEADT
7 0 2 0 0.00% 0.00% 0.00% 0 Timers
8 0 9 0 0.00% 0.00% 0.00% 0 AAA high-capacit
9 8 158 50 0.00% 0.00% 0.00% 0 SNTP
10 1034 5268 196 0.00% 0.02% 0.00% 0 ARP Input
11 2 2 1000 0.00% 0.00% 0.00% 0 Entity MIB API
12 2 1494 1 0.00% 0.00% 0.00% 0 HC Counter Timer
13 2 5973 0 0.00% 0.00% 0.00% 0 GraphIt
14 0 11 0 0.00% 0.00% 0.00% 0 Net Input
15 0 1 0 0.00% 0.00% 0.00% 0 Critical Bkgnd
16 34 1906 17 0.00% 0.00% 0.00% 0 Net Background
17 4 101 39 0.00% 0.00% 0.00% 0 Logger
18 24 5969 4 0.00% 0.00% 0.00% 0 TTY Background
19 5 5998 0 0.00% 0.00% 0.00% 0 Per-Second Jobs
20 0 1196 0 0.00% 0.00% 0.00% 0 Compute load avg
21 433 127 3409 0.00% 0.00% 0.00% 0 Per-minute Jobs
22 587 181376 3 0.00% 0.00% 0.00% 0 Dot11 driver
23 0 2 0 0.00% 0.00% 0.00% 0 Dot11 driver log
24 2 1200 1 0.00% 0.00% 0.00% 0 Voice Metrics Ta
25 44 39944 1 0.00% 0.00% 0.00% 0 SOAP LED Process
26 238 3309 71 0.00% 0.00% 0.00% 0 AAA Server
27 0 1 0 0.00% 0.00% 0.00% 0 AAA ACCT Proc
28 0 1 0 0.00% 0.00% 0.00% 0 ACCT Periodic Pr
29 10607 39208 270 0.31% 0.16% 0.09% 0 IP Input
30 0 1 0 0.00% 0.00% 0.00% 0 ICMP event handl
31 0 2 0 0.00% 0.00% 0.00% 0 AAA Dictionary R
32 96 999 96 0.00% 0.00% 0.00% 0 CDP Protocol
33 2 5997 0 0.00% 0.00% 0.00% 0 linktest
34 14 115 121 0.00% 0.00% 0.00% 0 Dot11 aaa proces
35 1 100 10 0.00% 0.00% 0.00% 0 pmkid
36 116 2261 51 0.00% 0.00% 0.00% 0 Dot11 Mgmt & Ass
37 18 7228 2 0.00% 0.00% 0.00% 0 AiroIAPP Protoco
38 0 2 0 0.00% 0.00% 0.00% 0 Triggered events
39 0 2 0 0.00% 0.00% 0.00% 0 Dot11 auth Dot1x
40 0 1 0 0.00% 0.00% 0.00% 0 Dot11 Mac Auth
41 2 1200 1 0.00% 0.00% 0.00% 0 Dot11CACprocess
42 59 2009 29 0.00% 0.00% 0.00% 0 TCP Timer
43 0 1 0 0.00% 0.00% 0.00% 0 TCP Protocols
44 0 1 0 0.00% 0.00% 0.00% 0 Socket Timers
45 14 54 259 0.00% 0.00% 0.00% 0 DHCPD Receive
46 48468 30304 1599 9.35% 1.66% 0.36% 0 HTTP CORE
47 0 2 0 0.00% 0.00% 0.00% 0 Soap Upgrade fet
48 0 2 0 0.00% 0.00% 0.00% 0 DDP
49 707 3309 213 0.00% 0.02% 0.00% 0 LOCAL AAA
50 1 2 500 0.00% 0.00% 0.00% 0 AAA Cached Serve
51 0 2 0 0.00% 0.00% 0.00% 0 ENABLE AAA
52 0 2 0 0.00% 0.00% 0.00% 0 LINE AAA
54 0 2 0 0.00% 0.00% 0.00% 0 TPLUS
55 0 3 0 0.00% 0.00% 0.00% 0 Crypto WUI
56 0 1 0 0.00% 0.00% 0.00% 0 EM Background Pr
57 1 3 333 0.00% 0.00% 0.00% 0 Soap Consoleless
58 6 4 1500 0.00% 0.00% 0.00% 0 Crypto CA
59 0 1 0 0.00% 0.00% 0.00% 0 Crypto PKI-CRL
60 0 1 0 0.00% 0.00% 0.00% 0 Crypto SSL
61 3 16 187 0.00% 0.00% 0.00% 0 AAA SEND STOP EV
62 0 2 0 0.00% 0.00% 0.00% 0 Dot11 LBS Proc
63 0 1 0 0.00% 0.00% 0.00% 0 Syslog Traps
65 0 50 0 0.00% 0.00% 0.00% 0 DHCPD Timer
66 8 6027 1 0.00% 0.00% 0.00% 0 DHCP Client
67 8349 84826 98 0.55% 0.17% 0.10% 0 HyBridge Input P
68 14 6744 2 0.00% 0.00% 0.00% 0 Tbridge Monitor
69 0 2 0 0.00% 0.00% 0.00% 0 Spanning Tree
70 0 1690 0 0.00% 0.00% 0.00% 0 DHCPD Database
------------------ show process cpu history ------------------
AP_WLAN_Bakery 12:32:06 PM Friday Oct 15 2010 -0400
1133333
667777766666
100
90
80
70
60
50
40 *****
30 *****
20 *******
10 ************
0....5....1....1....2....2....3....3....4....4....5....5....
0 5 0 5 0 5 0 5 0 5
CPU% per second (last 60 seconds)
7 37 78 7 8
11 121961 87 1 3 1 1
100
90 *
80 ** *
70 * * ** * *
60 * * ** * *
50 * * ** * *
40 * ** ** * *
30 * ** ** * *
20 * ** #* * *
10 #*## ## # #
0....5....1....1....2....2....3....3....4....4....5....5....
0 5 0 5 0 5 0 5 0 5
CPU% per minute (last 60 minutes)
* = maximum CPU% # = average CPU%
8
8
100
90 *
80 *
70 *
60 *
50 *
40 *
30 *
20 *
10 *
0....5....1....1....2....2....3....3....4....4....5....5....6....6....7.
0 5 0 5 0 5 0 5 0 5 0 5 0
CPU% per hour (last 72 hours)
* = maximum CPU% # = average CPU%
------------------ show dot11 associations all-client ------------------
------------------ show wlccp ap mobility traffic ------------------
------------------ show wlccp ap mobility forwarding ------------------
------------------ show inventory ------------------
NAME: "AP1210", DESCR: "Cisco Aironet 1200 Series Access Point"
PID: ÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿÿ, VID: ÿÿÿ, SN: FTX0902R2V1
------------------ Mempool statistics ------------------
Head Total(b) Used(b) Free(b) Lowest(b) Largest(b)
Processor A4AB84 4709500 2431000 2278500 1920552 2125904
I/O ECB000 1265664 468008 797656 727168 779580
------------------ show memory summary -----------------
Processor memory
Alloc PC Size Blocks Bytes What
0x4790 0000000080 0000000001 0000000080 ACL Header
0x47A4 0000000024 0000000001 0000000024 Init
0x9FD4 0000000036 0000000001 0000000036 Init
0x9FFC 0000000040 0000000001 0000000040 Init
0xA018 0000000024 0000000001 0000000024 Init
0xA040 0000000036 0000000001 0000000036 Init
0xA134 0000000060 0000000001 0000000060 Init
0xF9D0 0000000024 0000000001 0000000024 HTTP CP
0xFAF8 0000000024 0000000001 0000000024 HTTP CP
0xFB6C 0000000076 0000000001 0000000076 HTTP CP
0xFC04 0000000024 0000000001 0000000024 HTTP CP
0xFC60 0000000028 0000000001 0000000028 HTTP CP
0xFD58 0000000024 0000000001 0000000024 Init
0xFDC4 0000000024 0000000001 0000000024 Init
0xFF2C 0000000036 0000000001 0000000036 HTTP CP
0xFF2C 0000000044 0000000001 0000000044 HTTP CP
0x11034 0000000024 0000000001 0000000024 Init
0x15750 0000004096 0000000001 0000004096 Init
0x1DD08 0000000120 0000000001 0000000120 Ion New Block
0x1F474 0000000024 0000000001 0000000024 LOGIN UNC PW
0x1F474 0000000056 0000000001 0000000056 LOGIN PWC (Free Blocks)
0x1F610 0000000080 0000000001 0000000080 local_aaa_authen2 (Free Blocks)
0x24F64 0000004784 0000000001 0000004784 (coalesced) (Free Blocks)
0x24F64 0000013956 0000000001 0000013956 (coalesced) (Free Blocks)
0x264F4 0000000512 0000000001 0000000512 Init
0x2CDF8 0000004312 0000000001 0000004312 TTY data
0x2E994 0000001500 0000000001 0000001500 String-DB entries
0x2E9BC 0000001500 0000000001 0000001500 String-DB owners
0x2E9E4 0000000776 0000000001 0000000776 String-DB handles
0x2E9FC 0000001024 0000000001 0000001024 String DB Hash Table
0x2F154 0000000024 0000000002 0000000048 SDB String
0x2F714 0000000176 0000000001 0000000176 SDB Owner info
0x2FF28 0000004312 0000000006 0000025872 TTY data
0x336E8 0000002000 0000000001 0000002000 TTY Input Buf
0x33720 0000000512 0000000001 0000000512 TTY Output Buf
0x3E6C0 0000000052 0000000003 0000000156 MAC ADDR subblock
0x40DA8 0000003000 0000000002 0000006000 keepalive sb chunk
0x42490 0000065536 0000000001 0000065536 Parseinfo Blocks
0x424B8 0000000364 0000000001 0000000364 tokenQ node
0x424E0 0000000432 0000000001 0000000432 Chain Cache Nodes
0x42508 0000032768 0000000001 0000032768 Parse Nodes
0x46E18 0000000120 0000000001 0000000120 Init
0x47028 0000000060 0000000001 0000000060 Init
0x47458 0000000024 0000000034 0000000816 Init
0x4755C 0000010000 0000000001 0000010000 Parser Linkage
0x47938 0000000056 0000000053 0000002968 Parser Mode
0x47938 0000000108 0000000001 0000000108 Parser Mode
0x479A4 0000000024 0000000054 0000001296 Parser Mode Q1
0x479C8 0000000024 0000000054 0000001296 Parser Mode Q2
0x49FA8 0000000432 0000000001 0000000432 Chain Cache No
0x4A070 0000000432 0000000009 0000003888 Chain Cache No
0x4A070 0000000432 0000000001 0000000432 Chain Cache No (Free Blocks)
0x4A070 0000000548 0000000001 0000000548 (coalesced) (Free Blocks)
0x4A160 0000000432 0000000001 0000000432 Chain Cache No
0x4FCD4 0000000256 0000000001 0000000256 HTTP CP
0x548F4 0000000032 0000000016 0000000512 Parser Alias
0x54924 0000000024 0000000016 0000000384 Init
0x5C338 0000004616 0000000001 0000004616 (coalesced) (Free Blocks)
0x5D464 0000000024 0000000001 0000000024 HTTP CP
0x5D4E4 0000000024 0000000001 0000000024 HTTP CP
0x65394 0000000024 0000000008 0000000192 Cond Debug definition
0x698F0 0000000068 0000000003 0000000204 GraphIt Data
0x6990C 0000001316 0000000003 0000003948 Graphit Client
0x69920 0000000024 0000000002 0000000048 Init
0x69920 0000000032 0000000001 0000000032 Init
0x73254 0000000164 0000000002 0000000328 Init
0x73278 0000000164 0000000002 0000000328 Init
0x7329C 0000000164 0000000002 0000000328 Init
0x7B12C 0000000164 0000000001 0000000164 Init
0x7B150 0000000164 0000000001 0000000164 Init
0x7B174 0000000164 0000000001 0000000164 Init
0x83E48 0000000060 0000000001 0000000060 HTTP CP
0x842C0 0000000044 0000000001 0000000044 HTTP CP
0x86C40 0000032772 0000000001 0000032772 Init
0x8AD2C 0000000024 0000000002 0000000048 AAA Secrettype
0x8AD64 0000000024 0000000002 0000000048 AAA Secrettype encrypt
0x8ADD0 0000000024 0000000002 0000000048 AAA_Secrettype pw
0x8B254 0000000192 0000000002 0000000384 AAA SG HEAD
0x8B294 0000000024 0000000002 0000000048 AAA SG NAME
0x8BFA8 0000000060 0000000001 0000000060 AAA MI SG NAME
0x8D1AC 0000003200 0000000001 0000003200 AAA attr list handle IDs
0x8DBA8 0000001024 0000000001 0000001024 AAA attr list handle IDs
0x9AE18 0000004096 0000000001 0000004096 AAA Unique Id Hash Table
0x9AED8 0000065536 0000000001 0000065536 AAA DB Chunk
0x9EFE8 0000020000 0000000001 0000020000 AAA Acct DB chunk
0xA0EA0 0000016336 0000000001 0000016336 AAA Acct Rec chunk
0xAFBC4 0000002048 0000000001 0000002048 AAA SG ID table
0xAFE78 0000001024 0000000003 0000003072 AAA SG ID table
0xB3D68 0000000032 0000000001 0000000032 Init
0xB4388 0000000024 0000000001 0000000024 AAA nvgend sg elt
0xB4388 0000000052 0000000001 0000000052 AAA nvgend sg elt
0xB43C0 0000000132 0000000002 0000000264 AAA Public Server Group
0xB4400 0000000028 0000000002 0000000056 AAA Public Server Group wrapper
0xB4448 0000000024 0000000002 0000000048 AAA pub SG servers
0xB44CC 0000000024 0000000002 0000000048 AAA pub SG wrap name
0xB4510 0000000024 0000000002 0000000048 AAA pub SG name
0xBC014 0000000776 0000000275 0000213400 *Free Packet Header*
0xBC014 0000000788 0000000001 0000000788 *Free Packet Header*
0xBC014 0000000804 0000000001 0000000804 *Free Packet Header*
0xBC014 0000000828 0000000001 0000000828 *Free Packet Header*
0xBC014 0000001408 0000000001 0000001408 (coalesced) (Free Blocks)
0xBC014 0000008480 0000000001 0000008480 (coalesced) (Free Blocks)
0xBCA88 0000000776 0000000003 0000002328 *In-use Packet Header*
0xC1274 0000004000 0000000001 0000004000 Packet Elements
0xC3B00 0000000184 0000000001 0000000184 IRB/CRB rxtypes
0xC3EE4 0000004712 0000000005 0000023560 *Hardware IDB*
0xC3EFC 0000001400 0000000005 0000007000 *Software IDB*
0xC4440 0000000024 0000000003 0000000072 HTTP CP
0xC4440 0000000076 0000000001 0000000076 HTTP CP
0xC4494 0000000024 0000000003 0000000072 HTTP CP
0xC4494 0000000080 0000000001 0000000080 HTTP CP
0xC4580 0000000184 0000000004 0000000736 IRB/CRB rxtypes
0xC4948 0000000048 0000000001 0000000048 HTTP CP
0xC4948 0000000052 0000000001 0000000052 HTTP CP
0xC4CB8 0000001400 0000000004 0000005600 *Software IDB*
0xC5864 0000000024 0000000004 0000000096 Init
0xC58E0 0000000024 0000000004 0000000096 Init
0xC8118 0000000032 0000000004 0000000128 IP Input
0xED1F0 0000035292 0000000001 0000035292 IDB List Element Chunks
0xFF3C0 0000000024 0000000059 0000001416 Init
0xFF7C4 0000000104 0000000008 0000000832 Init
0xFF7D4 0000000024 0000000006 0000000144 Init
0xFF7D4 0000000076 0000000001 0000000076 Init
0xFF7D4 0000000080 0000000001 0000000080 Init
0xFF8F4 0000000024 0000000001 0000000024 Init
0xFF9A4 0000000024 0000000007 0000000168 Init
0x102F38 0000010000 0000000001 0000010000 AAA chunk
0x103140 0000004616 0000000001 0000004616 AAA Acct AVLnode chunk
0x107F7C 0000000100 0000000001 0000000100 AAA MLIST
0x1081E8 0000000092 0000000001 0000000092 AAA MLIST
0x108A7C 0000001024 0000000002 0000002048 AAA mlist ID table
0x118430 0000001500 0000000007 0000010500 List Elements
0x119688 0000001500 0000000001 0000001500 List Elements
0x1196C8 0000005000 0000000001 0000005000 List Headers
0x11D7D4 0000001032 0000000001 0000001032 Process Array
0x11F5B0 0000000640 0000000068 0000043520 Process
0x11F5B0 0000000856 0000000001 0000000856 (coalesced) (Free Blocks)
0x1213A8 0000001500 0000000001 0000001500 Watched Semaph
0x1219A4 0000000144 0000000064 0000009216 Process Events
0x1219A4 0000000160 0000000002 0000000320 Process Events
0x1219A4 0000000172 0000000001 0000000172 Process Events
0x1219A4 0000000200 0000000001 0000000200 Process Events
0x1219A4 0000000208 0000000001 0000000208 Process Events
0x1219A4 0000000256 0000000001 0000000256 (coalesced) (Free Blocks)
0x1219A4 0000000432 0000000001 0000000432 (coalesced) (Free Blocks)
0x1219A4 0000000556 0000000001 0000000556 (coalesced) (Free Blocks)
0x123C24 0000001500 0000000001 0000001500 messages
0x123C50 0000001500 0000000001 0000001500 Watched messages
0x123C7C 0000010000 0000000001 0000010000 Watched Queue
0x123CA4 0000005000 0000000001 0000005000 Watched Boolean
0x123CCC 0000005000 0000000001 0000005000 Watched Bitfield
0x123CF4 0000001500 0000000001 0000001500 Watched Semaphore
0x123D18 0000005000 0000000001 0000005000 Watcher Info
0x123D40 0000000500 0000000001 0000000500 Watched Message Queue
0x123D68 0000001500 0000000001 0000001500 Watcher Message Queue
0x123D90 0000003000 0000000001 0000003000 Read/Write Locks
0x126050 0000002000 0000000001 0000002000 Reg Function 12
0x126078 0000001500 0000000001 0000001500 Reg Function iList
0x1260A0 0000001500 0000000001 0000001500 Reg Function Caselist
0x126118 0000002000 0000000005 0000010000 Reg Function 1
0x12657C 0000002000 0000000001 0000002000 Reg Function 1
0x129F50 0000000024 0000000002 0000000048 *Sched*
0x129F50 0000000032 0000000001 0000000032 *Sched*
0x129F50 0000000044 0000000008 0000000352 *Sched*
0x12A228 0000000256 0000000001 0000000256 Init
0x12C5F8 0000003000 0000000001 0000003000 CCA CCB chunks
0x12CDBC 0000000048 0000000008 0000000384 CCA Component
0x12CE24 0000000024 0000000007 0000000168 CCA Notification Flags
0x12CE24 0000000048 0000000001 0000000048 CCA Notification Flags
0x12CE84 0000003000 0000000008 0000024000 Keepalive
0x12CFF4 0000000024 0000000003 0000000072 CCA UserType
0x12D0A8 0000003000 0000000001 0000003000 CCA CLA chunks
0x1301C0 0000000024 0000000001 0000000024 TW Wheels
0x130200 0000016384 0000000003 0000049152 TW Buckets
0x13AA18 0000000112 0000000006 0000000672 Process Signals
0x13B01C 0000003000 0000000001 0000003000 Process Stack
0x13B01C 0000005500 0000000049 0000269500 Process Stack
0x13B01C 0000008000 0000000004 0000032000 Process Stack
0x13B01C 0000009000 0000000006 0000054000 Process Stack
0x13B01C 0000011000 0000000009 0000099000 Scheduler Stack
0x13B01C 0000018000 0000000001 0000018000 Interrupt Stack
0x13B01C 0002125900 0000000001 0002125900 (coalesced) (Free Blocks)
0x14F6BC 0000020000 0000000001 0000020000 Managed Chunk Queue Elements
0x151870 0000000068 0000000001 0000000068 (fragment) (Free Blocks)
0x1559A8 0000000296 0000000008 0000002368 Pool Info
0x155F84 0000000032 0000000001 0000000032 Pool Cache
0x15AF2C 0000000264 0000000001 0000000264 CLASSMAP_MODULE
0x15B7B0 0000000104 0000000001 0000000104 CLASSMAP_MODULE
0x15B8D0 0000000136 0000000001 0000000136 CLASSMAP_MODULE
0x15B8F0 0000000024 0000000001 0000000024 CLASSMAP_MODULE
0x15BA20 0000000024 0000000001 0000000024 CLASSMAP_MODULE
0x1826A8 0000000256 0000000001 0000000256 Init
0x182B78 0000000256 0000000001 0000000256 Init
0x1875C0 0000000776 0000000002 0000001552 *In-use Packet Header*
0x188DF4 0000000288 0000000003 0000000864 SNTP
0x188DF4 0000000332 0000000001 0000000332 DDP
0x1904D0 0000000776 0000000001 0000000776 *In-use Packet Header*
0x193CB8 0000001184 0000000005 0000005920 TCP CB
0x193CB8 0000000728 0000000001 0000000728 (fragment) (Free Blocks)
0x1A86AC 0000003000 0000000001 0000003000 IP Addresses
0x1AE490 0000000024 0000000004 0000000096 HTTP CP
0x1AE490 0000000032 0000000001 0000000032 Dot11 driver
0x1AE490 0000000048 0000000001 0000000048 AiroIAPP Protocol
0x1AE490 0000000068 0000000001 0000000068 HTTP CP
0x1CDDA0 0000000280 0000000004 0000001120 Init
0x1CDDAC 0000000068 0000000004 0000000272 Init
0x1EB928 0000005000 0000000001 0000005000 ip localpool
0x1EFFC4 0000000024 0000000001 0000000024 Init
0x1F9E40 0000001652 0000000003 0000004956 HTTP CORE
0x1F9EC8 0000000128 0000000003 0000000384 DHCPD Receive
0x1FBF20 0000000172 0000000002 0000000344 DHCPD Receive
0x1FBF20 0000000232 0000000001 0000000232 HTTP CORE
0x1FBF20 0000000500 0000000001 0000000500 (coalesced) (Free Blocks)
0x1FF2DC 0000000040 0000000001 0000000040 DHCPD Receive
0x206B78 0000000024 0000000003 0000000072 Init
0x206BA8 0000000024 0000000003 0000000072 Init
0x20BE88 0000001500 0000000001 0000001500 Syslogd Messages chunk
0x20FEF0 0000000024 0000000001 0000000024 Init
0x221B18 0000010000 0000000001 0000010000 Time Range Entry Chunks
0x221B40 0000003000 0000000001 0000003000 Time Range Item Chunks
0x221B68 0000001500 0000000001 0000001500 Time Range User Chunks
0x2221E4 0000000036 0000000016 0000000576 Init
0x222214 0000000040 0000000016 0000000640 Init
0x2233CCHi,
if you remove "encryption mode ciphers aes-ccm tkip" from the radio interface does it help?
it should remain like this:
interface Dot11Radio0
no ip address
no ip route-cache
encryption vlan 1 mode ciphers aes-ccm tkip
ssid WLAN_Corporate
ssid WLAN_HartKitGuest
HTH,
Tiago
If this helps you and/or answers your question please mark the question as "answered" and/or rate it, so other users can easily find it. -
Dynamin VPN/GRE can't ping other side of tunnel
I am new at this VPN stuff and tryiong to setup a GRE Dynamic IP VPN between my offfice and home. Here is what I ahve done thus far:
OFFICE
interface Tunnel0
ip address 172.30.1.1 255.255.255.252
no ip redirects
ip mtu 1400
ip nhrp map multicast dynamic
ip nhrp network-id 1
ip tcp adjust-mss 1360
tunnel source FastEthernet0/0
tunnel mode gre multipoint
tunnel key 1
interface FastEthernet0/0
ip address 40.197.68.9 255.255.255.248
ip nat outside
ip virtual-reassembly
duplex auto
speed auto
HOME
interface Tunnel0
ip address 172.30.1.2 255.255.255.252
ip mtu 1400
ip nhrp map multicast 40.197.68.9
ip nhrp map 172.30.1.1 40.197.68.9
ip nhrp network-id 1
ip nhrp nhs 172.30.1.1
ip tcp adjust-mss 1360
tunnel source GigabitEthernet0/0
tunnel destination 40.197.68.9
tunnel key 1
interface GigabitEthernet0/0
description Router
ip address 192.168.30.1 255.255.255.252
duplex auto
speed auto
When I ping 172.30.1.1 from the HOME router, I get 0/5 success. Not good! I have not setup any IPSec yet.
Results for HOME router
show ip nhrp nhs detail
Legend: E=Expecting replies, R=Responding, W=Waiting
Tunnel0:
172.30.1.1 E priority = 0 cluster = 0 req-sent 53 req-failed 0 repl-recv 0
sh int t0
Tunnel0 is up, line protocol is up
Hardware is Tunnel
Internet address is 172.30.1.2/30
MTU 17912 bytes, BW 100 Kbit/sec, DLY 50000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation TUNNEL, loopback not set
Keepalive not set
Tunnel source 192.168.30.1 (GigabitEthernet0/0), destination 40.197.68.9
Tunnel Subblocks:
src-track:
Tunnel0 source tracking subblock associated with GigabitEthernet0/0
Set of tunnels with source GigabitEthernet0/0, 1 member (includes iterators), on interface <OK>
Tunnel protocol/transport GRE/IP
Key 0x1, sequencing disabled
Checksumming of packets disabled
Tunnel TTL 255, Fast tunneling enabled
Tunnel transport MTU 1472 bytes
Tunnel transmit bandwidth 8000 (kbps)
Tunnel receive bandwidth 8000 (kbps)
Last input 00:40:28, output 00:00:25, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/0 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts (0 IP multicasts)
0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
106 packets output, 12612 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 unknown protocol drops
0 output buffer failures, 0 output buffers swapped out
sh ip route
Gateway of last resort is 192.168.30.2 to network 0.0.0.0
S* 0.0.0.0/0 [1/0] via 192.168.30.2
10.0.0.0/8 is variably subnetted, 4 subnets, 2 masks
C 10.110.0.0/24 is directly connected, GigabitEthernet0/1.110
L 10.110.0.1/32 is directly connected, GigabitEthernet0/1.110
C 10.115.0.0/24 is directly connected, GigabitEthernet0/1.115
L 10.115.0.1/32 is directly connected, GigabitEthernet0/1.115
172.16.0.0/30 is subnetted, 1 subnets
S 172.16.2.0 [1/0] via 192.168.30.6
172.30.0.0/16 is variably subnetted, 2 subnets, 2 masks
C 172.30.1.0/30 is directly connected, Tunnel0
L 172.30.1.2/32 is directly connected, Tunnel0
S 192.168.2.0/24 is directly connected, GigabitEthernet0/0
S 192.168.10.0/24 is directly connected, GigabitEthernet0/0
192.168.30.0/24 is variably subnetted, 4 subnets, 2 masks
C 192.168.30.0/30 is directly connected, GigabitEthernet0/0
L 192.168.30.1/32 is directly connected, GigabitEthernet0/0
C 192.168.30.4/30 is directly connected, GigabitEthernet0/1.30
L 192.168.30.5/32 is directly connected, GigabitEthernet0/1.30
S 192.168.50.0/24 [1/0] via 192.168.30.6
192.168.69.0/24 is variably subnetted, 2 subnets, 2 masks
C 192.168.69.0/24 is directly connected, GigabitEthernet0/1.69
L 192.168.69.3/32 is directly connected, GigabitEthernet0/1.69
S 192.168.100.0/24 [1/0] via 192.168.30.6
S 192.168.125.0/24 [1/0] via 192.168.30.6
S 192.168.200.0/24 [1/0] via 192.168.30.6
sh dmvpn
Interface: Tunnel0, IPv4 NHRP Details
Type:Spoke, NHRP Peers:1,
# Ent Peer NBMA Addr Peer Tunnel Add State UpDn Tm Attrb
1 50.197.68.90 172.30.1.1 NHRP 02:30:17 S
Results for OFFICE router
show ip nhrp nhs detail
sh dmvpn
sh int t0
Tunnel0 is up, line protocol is up
Hardware is Tunnel
Internet address is 172.30.1.1/30
MTU 17912 bytes, BW 100 Kbit/sec, DLY 50000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation TUNNEL, loopback not set
Keepalive not set
Tunnel source 40.197.68.9 (FastEthernet0/0)
Tunnel Subblocks:
src-track:
Tunnel0 source tracking subblock associated with FastEthernet0/0
Set of tunnels with source FastEthernet0/0, 1 member (includes iterators), on interface <OK>
Tunnel protocol/transport multi-GRE/IP
Key 0x1, sequencing disabled
Checksumming of packets disabled
Tunnel TTL 255, Fast tunneling enabled
Tunnel transport MTU 1472 bytes
Tunnel transmit bandwidth 8000 (kbps)
Tunnel receive bandwidth 8000 (kbps)
Last input 00:43:56, output never, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/0 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts (0 IP multicasts)
0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
0 packets output, 0 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 unknown protocol drops
0 output buffer failures, 0 output buffers swapped out
show ip route
S* 0.0.0.0/0 [1/0] via 40.197.68.94
40.0.0.0/8 is variably subnetted, 2 subnets, 2 masks
C 40.197.68.8/29 is directly connected, FastEthernet0/0
L 40.197.68.9/32 is directly connected, FastEthernet0/0
172.30.0.0/16 is variably subnetted, 2 subnets, 2 masks
C 172.30.1.0/30 is directly connected, Tunnel0
L 172.30.1.1/32 is directly connected, Tunnel0
S 192.168.2.0/24 [1/0] via 192.168.10.5
192.168.10.0/24 is variably subnetted, 2 subnets, 2 masks
C 192.168.10.0/24 is directly connected, FastEthernet0/1
L 192.168.10.1/32 is directly connected, FastEthernet0/1
S 192.168.69.0/24 is directly connected, FastEthernet0/0
Why can't Io ping from the HOME router to the OFFICE router?I fugured this problem out. I needed to setup PKI/IKE and once that was done on both routers, my tunned now passes some data.
-
My N2K connected to N5K, why some ports can set the port speed, and some cann't set the port speed?
int eth102/1/25 ！！！No speed command
(config-if)# ?
beacon Disable/enable the beacon for an interface
cdp Configure CDP interface parameters
channel-group Configure port channel parameters
description Enter description of maximum 80 characters
inherit Inherit a port-profile
ip Configure IP features
ipv6 Configure IPv6 features
lacp Configure LACP parameters
link Configure link
lldp Configure Interface LLDP parameters
logging Configure logging for interface
mvr-group MVR interface config
mvr-type MVR interface config
mvr-vlan Interface MVR Config
no Negate a command or set its defaults
rate-limit Set packet per second rate limit
service-policy Configure service policy for an interface
service-policy Policy Map
shutdown Enable/disable an interface
snmp Modify SNMP interface parameters
spanning-tree Spanning Tree Subsystem
switchport Configure switchport parameters
untagged Default to use for untagged packets on interface
end Go to exec mode
exit Exit from command interpreter
pop Pop mode from stack or restore from name
push Push current mode to stack or save it under name
where Shows the cli context you are in
(config-if)# int eth102/1/48 ！！！ include speed command
(config-if)# ?
bandwidth Set bandwidth informational parameter
beacon Disable/enable the beacon for an interface
cdp Configure CDP interface parameters
channel-group Configure port channel parameters
default Set a command to its defaults
delay Specify interface throughput delay
description Enter description of maximum 80 characters
duplex Enter the port duplex mode
fex Configure FEX fabric
flowcontrol Configure interface flowcontrol
hardware FEX Card type
inherit Inherit a port-profile
ip Configure IP features
ipv6 Configure IPv6 features
lacp Configure LACP parameters
link Configure link
lldp Configure Interface LLDP parameters
load-interval Specify interval for load calculation for an interface
logging Configure logging for interface
mac MAC
mac-address Configure interface mac address
mvr-group MVR interface config
mvr-type MVR interface config
mvr-vlan Interface MVR Config
negotiate Configure link negotiation parameters
no Negate a command or set its defaults
priority-flow-control Enable/Disable PFC
rate-limit Set packet per second rate limit
service-policy Configure service policy for an interface
service-policy Policy Map
shutdown Enable/disable an interface
snmp Modify SNMP interface parameters
spanning-tree Spanning Tree Subsystem
speed Enter the port speed
storm-control Configure Interface storm control
switchport Configure switchport parameters
untagged Default to use for untagged packets on interface
vpc Virtual Port Channel configuration
vtp Enable VTP on this interface
end Go to exec mode
exit Exit from command interpreter
pop Pop mode from stack or restore from name
push Push current mode to stack or save it under name
where Shows the cli context you are in
1,N5K version:
Cisco Nexus Operating System (NX-OS) Software
TAC support: http://www.cisco.com/tac
Documents: http://www.cisco.com/en/US/products/ps9372/tsd_products_support_series_home.html
Copyright (c) 2002-2013, Cisco Systems, Inc. All rights reserved.
The copyrights to certain works contained herein are owned by
other third parties and are used and distributed under license.
Some parts of this software are covered under the GNU Public
License. A copy of the license is available at
http://www.gnu.org/licenses/gpl.html.
Software
BIOS: version 3.6.0
loader: version N/A
kickstart: version 6.0(2)N1(2)
system: version 6.0(2)N1(2)
Power Sequencer Firmware:
Module 1: version v5.0
Microcontroller Firmware: version v1.0.0.2
SFP uC: Module 1: v1.1.0.0
QSFP uC: Module not detected
BIOS compile time: 05/09/2012
kickstart image file is: bootflash:///n5000-uk9-kickstart.6.0.2.N1.2.bin
kickstart compile time: 3/14/2013 1:00:00 [03/14/2013 16:53:55]
system image file is: bootflash:///n5000-uk9.6.0.2.N1.2.bin
system compile time: 3/14/2013 1:00:00 [03/14/2013 19:28:50]
Hardware
cisco Nexus 5596 Chassis ("O2 48X10GE/Modular Supervisor")
Intel(R) Xeon(R) CPU with 8262944 kB of memory.
2,N5K port
Eth102/1/1 -- connected 101 full 1000 --
Eth102/1/2 -- connected 101 full 1000 --
Eth102/1/3 -- connected 101 full 1000 --
Eth102/1/4 -- connected 101 full 1000 --
Eth102/1/5 -- connected 101 full 1000 --
Eth102/1/6 -- connected 101 full 1000 --
Eth102/1/7 -- connected 101 full 1000 --
Eth102/1/8 -- connected 101 full 1000 --
Eth102/1/9 -- connected 101 full 1000 --
Eth102/1/10 -- connected 101 full 1000 --
Eth102/1/11 -- connected 101 full 1000 --
Eth102/1/12 -- connected 101 full 1000 --
Eth102/1/13 -- connected 101 full 1000 --
Eth102/1/14 -- connected 101 full 1000 --
Eth102/1/15 -- connected 104 full 1000 --
Eth102/1/16 -- connected 104 full 1000 --
Eth102/1/17 -- connected 104 full 1000 --
Eth102/1/18 -- connected 104 full 1000 --
Eth102/1/19 -- connected 104 full 1000 --
Eth102/1/20 -- connected 104 full 1000 --
Eth102/1/21 -- connected 104 full 1000 --
Eth102/1/22 -- connected 104 full 1000 --
Eth102/1/23 -- connected 104 full 1000 --
Eth102/1/24 -- connected 104 full 1000 --
Eth102/1/25 -- notconnec 102 auto auto --
Eth102/1/26 -- notconnec 102 auto auto --
Eth102/1/27 -- connected 106 full 1000 --
Eth102/1/28 -- connected 106 full 1000 --
Eth102/1/29 -- connected 104 full 1000 --
Eth102/1/30 -- connected 104 full 1000 --
Eth102/1/31 -- connected 104 full 1000 --
Eth102/1/32 -- connected 104 full 1000 --
Eth102/1/33 -- connected 104 full 1000 --
Eth102/1/34 -- connected 104 full 1000 --
Eth102/1/35 -- connected 104 full 1000 --
Eth102/1/36 -- connected 104 full 1000 --
Eth102/1/37 -- connected 104 full 1000 --
Eth102/1/38 -- connected 104 full 1000 --
Eth102/1/39 -- notconnec 1 auto auto --
Eth102/1/40 -- notconnec 1 auto auto --
Eth102/1/41 -- notconnec 1 auto auto --
Eth102/1/42 -- notconnec 1 auto auto --
Eth102/1/43 -- notconnec 1 auto auto --
Eth102/1/44 -- notconnec 1 auto auto --
Eth102/1/45 -- notconnec 1 auto auto --
Eth102/1/46 -- notconnec 1 auto auto --
Eth102/1/47 -- notconnec 1 auto auto --
Eth102/1/48 ZTC-Switch-48 connected 105 full 100 --
3,Fex
show fex 102 det
FEX: 102 Description: AO4-N2K-FEX102 state: Online
FEX version: 6.0(2)N1(2) [Switch version: 6.0(2)N1(2)]
FEX Interim version: 6.0(2)N1(2)
Switch Interim version: 6.0(2)N1(2)
Extender Serial: FOX1742G09B
Extender Model: N2K-C2248TP-E-1GE, Part No: 73-13671-02
Card Id: 149, Mac Addr: 64:e9:50:16:08:02, Num Macs: 64
Module Sw Gen: 21 [Switch Sw Gen: 21]
post level: complete
Pinning-mode: static Max-links: 1
Fabric port for control traffic: Eth1/3
FCoE Admin: false
FCoE Oper: true
FCoE FEX AA Configured: false
Fabric interface state:
Po102 - Interface Up. State: Active
Eth1/1 - Interface Up. State: Active
Eth1/2 - Interface Up. State: Active
Eth1/3 - Interface Up. State: Active
Eth1/4 - Interface Up. State: Active
Fex Port State Fabric Port
Eth102/1/1 Up Po102
Eth102/1/2 Up Po102
Eth102/1/3 Up Po102
Eth102/1/4 Up Po102
Eth102/1/5 Up Po102
Eth102/1/6 Up Po102
Eth102/1/7 Up Po102
Eth102/1/8 Up Po102
Eth102/1/9 Up Po102
Eth102/1/10 Up Po102
Eth102/1/11 Up Po102
Eth102/1/12 Up Po102
Eth102/1/13 Up Po102
Eth102/1/14 Up Po102
Eth102/1/15 Up Po102
Eth102/1/16 Up Po102show run int eth102/1/25 all
!Command: show running-config interface Ethernet102/1/25 all
!Time: Tue Apr 14 14:33:38 2009
version 6.0(2)N1(2)
interface Ethernet102/1/25
no description
lacp port-priority 32768
lacp rate normal
priority-flow-control mode auto
lldp transmit
lldp receive
no switchport block unicast
no switchport block multicast
no hardware multicast hw-hash
no hardware vethernet mac filtering per-vlan
cdp enable
switchport
switchport mode access
no switchport dot1q ethertype
no switchport priority extend
switchport access vlan 102
spanning-tree port-priority 128
spanning-tree cost auto
spanning-tree link-type auto
spanning-tree port type edge
spanning-tree bpduguard enable
no spanning-tree bpdufilter
speed auto
duplex auto
flowcontrol receive off
flowcontrol send on
no link debounce
no beacon
delay 1
snmp trap link-status
logging event port link-status default
logging event port trunk-status default
mdix auto
storm-control broadcast level 100.00
storm-control multicast level 100.00
storm-control unicast level 100.00
no shutdown lan
load-interval counter 1 30
load-interval counter 2 300
no load-interval counter 3
medium broadcast
channel-group 2025 mode active
no shutdown
show run int eth102/1/48 all
!Command: show running-config interface Ethernet102/1/48 all
!Time: Tue Apr 14 14:35:08 2009
version 6.0(2)N1(2)
interface Ethernet102/1/48
description ZTC-Switch-48
lacp port-priority 32768
lacp rate normal
priority-flow-control mode auto
lldp transmit
lldp receive
no switchport block unicast
no switchport block multicast
no hardware multicast hw-hash
no hardware vethernet mac filtering per-vlan
cdp enable
switchport
switchport mode access
no switchport dot1q ethertype
no switchport priority extend
switchport access vlan 105
spanning-tree port-priority 128
spanning-tree cost auto
spanning-tree link-type auto
spanning-tree port type edge
spanning-tree bpduguard enable
no spanning-tree bpdufilter
speed auto
duplex auto
flowcontrol receive off
flowcontrol send on
no link debounce
no beacon
delay 1
snmp trap link-status
logging event port link-status default
logging event port trunk-status default
mdix auto
storm-control broadcast level 100.00
storm-control multicast level 100.00
storm-control unicast level 100.00
no shutdown lan
load-interval counter 1 30
load-interval counter 2 300
no load-interval counter 3
medium broadcast
no shutdown
Ports are connected, there is no relationship with the speed option, such as port 102/1/1 is connected, but no speed option, port 102/1/47 is notconnected, there speed options.
show int eth102/1/1
Ethernet102/1/1 is up
Belongs to Po2001
Hardware: 100/1000 Ethernet, address: 64e9.5016.0802 (bia 64e9.5016.0802)
MTU 1500 bytes, BW 1000000 Kbit, DLY 10 usec
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA
Port mode is access
full-duplex, 1000 Mb/s
Beacon is turned off
Input flow-control is off, output flow-control is on
Switchport monitor is off
EtherType is 0x8100
Last link flapped 1d02h
int eth102/1/1
(config-if)# ?
beacon Disable/enable the beacon for an interface
cdp Configure CDP interface parameters
channel-group Configure port channel parameters
description Enter description of maximum 80 characters
inherit Inherit a port-profile
ip Configure IP features
ipv6 Configure IPv6 features
lacp Configure LACP parameters
link Configure link
lldp Configure Interface LLDP parameters
logging Configure logging for interface
mvr-group MVR interface config
mvr-type MVR interface config
mvr-vlan Interface MVR Config
no Negate a command or set its defaults
rate-limit Set packet per second rate limit
service-policy Configure service policy for an interface
service-policy Policy Map
shutdown Enable/disable an interface
snmp Modify SNMP interface parameters
spanning-tree Spanning Tree Subsystem
switchport Configure switchport parameters
untagged Default to use for untagged packets on interface
end Go to exec mode
exit Exit from command interpreter
pop Pop mode from stack or restore from name
push Push current mode to stack or save it under name
where Shows the cli context you are in
show int eth102/1/47
Ethernet102/1/47 is down (Link not connected)
Hardware: 100/1000 Ethernet, address: 64e9.5016.0830 (bia 64e9.5016.0830)
MTU 1500 bytes, BW 0 Kbit, DLY 10 usec
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA
Port mode is access
auto-duplex, auto-speed
Beacon is turned off
Input flow-control is off, output flow-control is on
Switchport monitor is off
EtherType is 0x8100
int eth102/1/47
(config-if)# ?
bandwidth Set bandwidth informational parameter
beacon Disable/enable the beacon for an interface
cdp Configure CDP interface parameters
channel-group Configure port channel parameters
default Set a command to its defaults
delay Specify interface throughput delay
description Enter description of maximum 80 characters
duplex Enter the port duplex mode
fex Configure FEX fabric
flowcontrol Configure interface flowcontrol
hardware FEX Card type
inherit Inherit a port-profile
ip Configure IP features
ipv6 Configure IPv6 features
lacp Configure LACP parameters
link Configure link
lldp Configure Interface LLDP parameters
load-interval Specify interval for load calculation for an interface
logging Configure logging for interface
mac MAC
mac-address Configure interface mac address
mvr-group MVR interface config
mvr-type MVR interface config
mvr-vlan Interface MVR Config
negotiate Configure link negotiation parameters
no Negate a command or set its defaults
priority-flow-control Enable/Disable PFC
rate-limit Set packet per second rate limit
service-policy Configure service policy for an interface
service-policy Policy Map
shutdown Enable/disable an interface
snmp Modify SNMP interface parameters
spanning-tree Spanning Tree Subsystem
speed Enter the port speed
storm-control Configure Interface storm control
switchport Configure switchport parameters
untagged Default to use for untagged packets on interface
vpc Virtual Port Channel configuration
vtp Enable VTP on this interface
end Go to exec mode
exit Exit from command interpreter
pop Pop mode from stack or restore from name
push Push current mode to stack or save it under name
where Shows the cli context you are in -
Speed negotiation settings for a 10G interface
HI,
We have the following setup:
2 ports of CISCO 6509(also has xfp long range) switch connected to 2(XAUI) ports of SPARC box T5220.
When the SPARC box goes for a reboot, the link is UP at XAUI while ports are down at CISCO end.
However either of the following brings the link up.
. shut/no shut at 6509 or
. unplug and replug the cable.
No speed negotiation is configured at XAUI.
I would like to know if 10G CISCO 6509 by default has autonegotiation on?
From the document "Configuring and Troubleshooting Ethernet 10/100/1000Mb Half/Full Duplex Auto-Negotiation"
I found the following line
"By default, all devices are supposed to perform autonegotiation. 802.3z does not specifically define a way to turn Autonegotiation off, for both 1GigabitEthernet and 10GigabitEthernet."
Im seeing the following situation:
"Assume that there are two devices, A and B. Assume that each device can have Autonegotiation enabled, or disabled. The correct behaviour of link status with autonegotiation in accordance to the IEEE Std 802.3z-1998 should be like this:
If A is disabled and B is enabled, then A should report link up and B should report link down."
Does it apply to 10 G inetrfaces also?
PFB the config output of CISCO 6509
Cisco IOS Software, s72033_rp Software (s72033_rp-IPBASEK9-M), Version 12.2(33)SXI5, RELEASE SOFTWARE (fc2)
cisco WS-C6509-E (R7000) processor (revision 1.5) with 983008K/65536K bytes of memory.
6 16 CEF720 16 port 10GE WS-X6716-10GE
6 Distributed Forwarding Card WS-F6700-DFC3C
interface TenGigabitEthernet1/6/16
description BKUP:SSCPRODENG-NXGE4
switchport
switchport access vlan 101
switchport mode access
spanning-tree portfast edge
end
NOLACORE#sh int te1/6/16
TenGigabitEthernet1/6/16 is up, line protocol is up (connected)
Hardware is C6k 10000Mb 802.3, address is f866.f220.5027 (bia f866.f220.5027)
Description: BKUP:SSCPRODENG-NXGE4
MTU 1500 bytes, BW 10000000 Kbit, DLY 10 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Full-duplex, 10Gb/s, media type is 10Gbase-LRM
input flow-control is on, output flow-control is off
ARP type: ARPA, ARP Timeout 04:00:00
Last input never, output 00:00:19, output hang never
Last clearing of "show interface" counters 7w4d
Input queue: 0/2000/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 81000 bits/sec, 7 packets/sec
207547040601 packets input, 34173665463903 bytes, 0 no buffer
Received 64391 broadcasts (0 multicasts)
0 runts, 0 giants, 0 throttles
36 input errors, 36 CRC, 66 frame, 0 overrun, 0 ignored
0 watchdog, 0 multicast, 0 pause input
0 input packets with dribble condition detected
380437679022 packets output, 276421252994669 bytes, 0 underruns
0 output errors, 0 collisions, 1 interface resets
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier, 0 PAUSE output
0 output buffer failures, 0 output buffers swapped out
From the above config output can we say that 10Gb/s speed is forced on the link?
Regards,
Tejaswi A.Justin,
Thanks very much for the tip!
Do you know if Oracle 10g has any kind of built-in tool for editing data? I have heard of "The Vault", but that appears to be a tool for administering database users, reports, etc. I am looking for some kind of tool that shows the data in a grid layout (like Microsoft Excel) and allows someone to edit and save data in that grid. A web-based tool would be best, but a desktop tool (especially if it's already part of Oracle 10g) would also be good.
Thanks again,
Rachel -
Nexus 5000 - Odd Ethernet interface behavior (link down inactive)
Hi Guys,
This would sound really trivial but it is very odd behavior.
- We have a server connected to a 2, Nexus 5000s (for resiliancy)
- When there is no config on the ethernet interfaces whatsoever, the ethernet interface is UP / UP, there is minimal amount of traffic on the link etc. E.g.
Ethernet1/16 is up
Hardware: 1000/10000 Ethernet, address: 000d.ece7.85d7 (bia 000d.ece7.85d7)
Description: shipley-p1.its RK14/A13
MTU 1500 bytes, BW 10000000 Kbit, DLY 10 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA
Port mode is access
full-duplex, 10 Gb/s, media type is 1/10g
Beacon is turned off
Input flow-control is off, output flow-control is off
Rate mode is dedicated
Switchport monitor is off
Last link flapped 00:00:07
Last clearing of "show interface" counters 05:42:32
30 seconds input rate 0 bits/sec, 0 packets/sec
30 seconds output rate 96 bits/sec, 0 packets/sec
Load-Interval #2: 5 minute (300 seconds)
input rate 0 bps, 0 pps; output rate 8 bps, 0 pps
RX
0 unicast packets 0 multicast packets 0 broadcast packets
0 input packets 0 bytes
0 jumbo packets 0 storm suppression packets
0 runts 0 giants 0 CRC 0 no buffer
0 input error 0 short frame 0 overrun 0 underrun 0 ignored
0 watchdog 0 bad etype drop 0 bad proto drop 0 if down drop
0 input with dribble 0 input discard
0 Rx pause
TX
0 unicast packets 163 multicast packets 0 broadcast packets
163 output packets 15883 bytes
0 jumbo packets
0 output errors 0 collision 0 deferred 0 late collision
0 lost carrier 0 no carrier 0 babble
0 Tx pause
1 interface resets
- As soon as I configure the link to be an access port, the link goes down, flagging "inactivity" E.g.
sh int e1/16
Ethernet1/16 is down (inactive)
Hardware: 1000/10000 Ethernet, address: 000d.ece7.85d7 (bia 000d.ece7.85d7)
Description: shipley-p1.its RK14/A13
MTU 1500 bytes, BW 10000000 Kbit, DLY 10 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA
Port mode is access
auto-duplex, 10 Gb/s, media type is 1/10g
Beacon is turned off
Input flow-control is off, output flow-control is off
Rate mode is dedicated
Switchport monitor is off
Last link flapped 05:38:03
Last clearing of "show interface" counters 05:41:33
30 seconds input rate 0 bits/sec, 0 packets/sec
30 seconds output rate 0 bits/sec, 0 packets/sec
Load-Interval #2: 5 minute (300 seconds)
input rate 0 bps, 0 pps; output rate 0 bps, 0 pps
RX
0 unicast packets 0 multicast packets 0 broadcast packets
0 input packets 0 bytes
0 jumbo packets 0 storm suppression packets
0 runts 0 giants 0 CRC 0 no buffer
0 input error 0 short frame 0 overrun 0 underrun 0 ignored
0 watchdog 0 bad etype drop 0 bad proto drop 0 if down drop
0 input with dribble 0 input discard
0 Rx pause
TX
0 unicast packets 146 multicast packets 0 broadcast packets
146 output packets 13083 bytes
0 jumbo packets
0 output errors 0 collision 0 deferred 0 late collision
0 lost carrier 0 no carrier 0 babble
0 Tx pause
0 interface resets
- This behavior is seen on both 5Ks
- I've tried using a different set of ports, changed SFPs, and fibre cabling to no avail
- I can't seem to understand this behavior?! In that, why would configuring the port cause the link to go down?
- If anyone has experience this before, or could shed some light on this behavior, it would be appreciated.
sh ver
Cisco Nexus Operating System (NX-OS) Software
TAC support: http://www.cisco.com/tac
Copyright (c) 2002-2010, Cisco Systems, Inc. All rights reserved.
The copyrights to certain works contained herein are owned by
other third parties and are used and distributed under license.
Some parts of this software are covered under the GNU Public
License. A copy of the license is available at
http://www.gnu.org/licenses/gpl.html.
Software
BIOS: version 1.2.0
loader: version N/A
kickstart: version 4.2(1)N1(1)
system: version 4.2(1)N1(1)
power-seq: version v1.2
BIOS compile time: 06/19/08
kickstart image file is: bootflash:/n5000-uk9-kickstart.4.2.1.N1.1.bin
kickstart compile time: 4/29/2010 19:00:00 [04/30/2010 02:38:04]
system image file is: bootflash:/n5000-uk9.4.2.1.N1.1.bin
system compile time: 4/29/2010 19:00:00 [04/30/2010 03:51:47]
thanks
SheldonI had identical issue
Two interfaces on two different FEXes were INACTIVE. I have two Nexus 5596 in vPC and A/A FEXes.
I also use config-sync feature.
Very same configuration was applied to other ports on other FEXes and they were working with no problems.
interface Ethernet119/1/1
inherit port-profile PP-Exchange2003
I checked VLAN status associated with this profile and it was active (of course it was, other ports were ok).
I solved it by removing port profile from this port and re-applied it... voila, port changed state to up!
Very very strange. -
No connectivity - ports up and down?
I have a 2950 switch which we use to for connectivity to VOIP phones and terminals/pcs on the floors. At random times during the day maybe twice 2-3 hour span, we lose connectivity between two of the terminals and our server which is connected to the switch. When I say "lose connectivity" I mean the terminal is unable to reach our server(we have desktop vitalization) that hosts the virtual hosting software. All the terminals have static IP addresses assigned. The ports on the switch show no activity what so ever - at one stage I did see did an amber light blink every 2-3 seconds .This happened on the terminals that could not connect, but that has not repeated itself. Below I have included a sh int of a port that is currently down. The port could be down most of the day and then start working all of a sudden!
I don't know if a problem with the switch or port or communication with the server. Out of all the 12 terminals we have 10 of them have no problem connecting to the server through the same switch. When pinging from my pc to any of the two statically assigned IPs - host unreachable is returned.
Any help would be appreciated
FastEthernet0/48 is down, line protocol is down (notconnect)
Hardware is Fast Ethernet, address is 0017.596c.26b0 (bia 0017.596c.26b0)
MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Auto-duplex, Auto-speed, media type is 100BaseTX
input flow-control is unsupported output flow-control is unsupported
ARP type: ARPA, ARP Timeout 04:00:00
Last input never, output 07:54:51, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 0 bits/sec, 0 packets/sec
127223 packets input, 21345203 bytes, 0 no buffer
Received 1913 broadcasts (0 multicast)
0 runts, 0 giants, 0 throttles
15 input errors, 12 CRC, 3 frame, 0 overrun, 0 ignored
0 watchdog, 459 multicast, 0 pause input
0 input packets with dribble condition detected
76367875 packets output, 3852147285 bytes, 0 underruns
150 output errors, 0 collisions, 2 interface resets
0 babbles, 150 late collision, 9 deferred
0 lost carrier, 0 no carrier, 0 PAUSE output
0 output buffer failures, 0 output buffers swapped outCollin,
attached is the brief for the port been up...I can see that it is up and blinking green however on the terminal the screen is in a "frozen" state. When I rebooted the terminal it is trying to connect to the server - again the port is blinking green.
FastEthernet0/48 is up, line protocol is up (connected)
Hardware is Fast Ethernet, address is 0017.596c.26b0 (bia 0017.596c.26b0)
MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Full-duplex, 100Mb/s, media type is 100BaseTX
input flow-control is unsupported output flow-control is unsupported
ARP type: ARPA, ARP Timeout 04:00:00
Last input never, output 00:00:00, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 9000 bits/sec, 12 packets/sec
127300 packets input, 21363075 bytes, 0 no buffer
Received 1916 broadcasts (0 multicast)
0 runts, 0 giants, 0 throttles
15 input errors, 12 CRC, 3 frame, 0 overrun, 0 ignored
0 watchdog, 459 multicast, 0 pause input
0 input packets with dribble condition detected
76373604 packets output, 3852796867 bytes, 0 underruns
150 output errors, 0 collisions, 2 interface resets
0 babbles, 150 late collision, 9 deferred
0 lost carrier, 0 no carrier, 0 PAUSE output
0 output buffer failures, 0 output buffers swapped out -
SSH and Ping to WAN IP not working correctly.
Hey all!
I've run into an issue that i cant seem to figure out. For some reason i can't SSH to my router, and i also cant ping the WAN IP addresses, which i need for my monitoring service. This ones got me stuck so any help is very much appreciated. Here is my sanitized config. Thanks!
version 15.1
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
no aaa new-model
dot11 syslog
ip source-route
ip cef
ip domain name xxxxxxx
no ipv6 cef
multilink bundle-name authenticated
voice-card 0
crypto pki token default removal timeout 0
username admin privilege 0 password 7 xxxxxxxxxxxxxxxxx
redundancy
interface FastEthernet0/0
ip address xx.xx.xxx.xxx 255.255.255.240
ip access-group OutsideIn in
ip nat outside
ip virtual-reassembly in
duplex auto
speed auto
interface FastEthernet0/1
no ip address
ip virtual-reassembly in
duplex auto
speed auto
interface FastEthernet0/1.10
encapsulation dot1Q 10
ip address 10.10.100.60 255.255.0.0
interface FastEthernet0/1.20
encapsulation dot1Q 20
ip address 10.34.1.1 255.255.240.0
ip helper-address 10.34.1.7
ip nat inside
ip virtual-reassembly in
interface FastEthernet0/1.30
encapsulation dot1Q 30
ip address 10.60.0.1 255.255.252.0
ip helper-address 10.34.1.7
ip nat inside
ip virtual-reassembly in
interface FastEthernet0/1.31
encapsulation dot1Q 31
ip address 10.31.1.2 255.255.0.0
ip helper-address 10.34.1.7
ip nat inside
ip virtual-reassembly in
interface FastEthernet0/1.32
encapsulation dot1Q 32
ip address 10.32.1.2 255.255.0.0
ip helper-address 10.34.1.7
ip nat inside
ip virtual-reassembly in
interface FastEthernet0/1.33
encapsulation dot1Q 33
ip address 10.33.1.1 255.255.0.0
ip helper-address 10.34.1.7
ip nat inside
ip virtual-reassembly in
interface FastEthernet0/1.50
encapsulation dot1Q 50
ip address 10.50.1.2 255.255.0.0
ip nat inside
ip virtual-reassembly in
interface FastEthernet0/1.51
encapsulation dot1Q 51
ip address 10.51.1.1 255.255.0.0
ip helper-address 10.34.1.7
ip nat inside
ip virtual-reassembly in
interface FastEthernet0/1.52
encapsulation dot1Q 52
ip address 10.52.1.1 255.255.0.0
ip helper-address 10.34.1.7
ip nat inside
ip virtual-reassembly in
interface FastEthernet0/1.53
encapsulation dot1Q 53
ip address 10.53.1.1 255.255.0.0
ip helper-address 10.34.1.7
no ip redirects
ip nat inside
ip virtual-reassembly in
interface FastEthernet0/1.54
encapsulation dot1Q 54
ip address 10.54.1.1 255.255.0.0
ip helper-address 10.34.1.7
no ip redirects
ip nat inside
ip virtual-reassembly in
interface FastEthernet0/1.55
encapsulation dot1Q 55
ip address 10.55.1.1 255.255.0.0
ip helper-address 10.34.1.7
ip nat inside
ip virtual-reassembly in
interface FastEthernet0/1.56
encapsulation dot1Q 56
ip address 10.56.1.1 255.255.0.0
ip helper-address 10.34.1.7
no ip redirects
ip nat inside
ip virtual-reassembly in
ip forward-protocol nd
ip http server
no ip http secure-server
ip nat inside source list 100 interface FastEthernet0/0 overload
ip nat inside source static tcp 10.34.1.155 8020 interface FastEthernet0/0 8020
ip nat inside source static udp 10.34.1.155 8020 interface FastEthernet0/0 8020
ip nat inside source static tcp 10.34.1.155 8025 interface FastEthernet0/0 8025
ip nat inside source static udp 10.34.1.155 8025 interface FastEthernet0/0 8025
ip nat inside source static tcp 10.34.1.165 8030 interface FastEthernet0/0 8030
ip nat inside source static tcp 10.34.1.165 8035 interface FastEthernet0/0 8035
ip nat inside source static udp 10.34.1.165 8035 interface FastEthernet0/0 8035
ip nat inside source static udp 10.34.1.165 8030 interface FastEthernet0/0 8030
ip nat inside source static tcp 10.34.1.156 8010 interface FastEthernet0/0 8010
ip nat inside source static udp 10.34.1.156 8010 interface FastEthernet0/0 8010
ip nat inside source static tcp 10.34.1.156 8015 interface FastEthernet0/0 8015
ip nat inside source static udp 10.34.1.156 8015 interface FastEthernet0/0 8015
ip nat inside source static tcp 10.34.1.3 8061 interface FastEthernet0/0 8061
ip nat inside source static udp 10.34.1.3 8061 interface FastEthernet0/0 8061
ip nat inside source static tcp 10.34.1.3 8062 interface FastEthernet0/0 8062
ip nat inside source static udp 10.34.1.3 8062 interface FastEthernet0/0 8062
ip nat inside source static tcp 10.34.1.3 8063 interface FastEthernet0/0 8063
ip nat inside source static udp 10.34.1.3 8063 interface FastEthernet0/0 8063
ip nat inside source static tcp 10.34.1.3 8064 interface FastEthernet0/0 8064
ip nat inside source static udp 10.34.1.3 8064 interface FastEthernet0/0 8064
ip nat inside source static tcp 10.34.1.3 8065 interface FastEthernet0/0 8065
ip nat inside source static udp 10.34.1.3 8065 interface FastEthernet0/0 8065
ip nat inside source static tcp 10.34.1.3 8066 interface FastEthernet0/0 8066
ip nat inside source static udp 10.34.1.3 8066 interface FastEthernet0/0 8066
ip nat inside source static tcp 10.34.1.7 3389 interface FastEthernet0/0 3389
ip nat inside source static tcp 10.34.2.87 80 interface FastEthernet0/0 80
ip nat inside source static udp 10.34.2.87 80 interface FastEthernet0/0 80
ip nat inside source static tcp 10.34.1.16 80 interface FastEthernet0/0 8045
ip nat inside source static udp 10.34.1.16 80 interface FastEthernet0/0 8045
ip nat inside source static tcp 10.34.1.17 80 interface FastEthernet0/0 8055
ip nat inside source static udp 10.34.1.17 80 interface FastEthernet0/0 8055
ip nat inside source static tcp 10.34.1.18 80 interface FastEthernet0/0 8056
ip nat inside source static udp 10.34.1.18 80 interface FastEthernet0/0 8056
ip route 0.0.0.0 0.0.0.0 (NEXT HOP)
ip access-list extended OutsideIn
permit ip any host xx.xx.xxx.xxx
permit ip any host xx.xx.xxx.xxx
deny udp any any eq 1723
deny tcp any any eq 1723
deny udp any any eq isakmp
deny tcp any any eq 500
deny udp any any eq non500-isakmp
deny tcp any any eq 4500
permit tcp any host (WAN IP) eq www
permit tcp any host (WAN IP) eq 8010
permit udp any host (WAN IP) eq 8010
permit tcp any host (WAN IP) eq 8015
permit udp any host (WAN IP) eq 8015
permit tcp any host (WAN IP) eq 8020
permit udp any host (WAN IP) eq 8020
permit tcp any host (WAN IP) eq 8025
permit udp any host (WAN IP) eq 8025
permit tcp any host (WAN IP) eq 8030
permit udp any host (WAN IP) eq 8030
permit tcp any host (WAN IP) eq 8035
permit udp any host (WAN IP) eq 8035
permit tcp any host (WAN IP) eq 8045
permit udp any host (WAN IP) eq 8045
permit tcp any host (WAN IP) eq 8055
permit udp any host (WAN IP) eq 8055
permit tcp any host (WAN IP) eq 8061
permit udp any host (WAN IP) eq 8061
permit tcp any host (WAN IP) eq 8062
permit udp any host (WAN IP) eq 8062
permit tcp any host (WAN IP) eq 8063
permit udp any host (WAN IP) eq 8063
permit tcp any host (WAN IP) eq 8064
permit udp any host (WAN IP) eq 8064
permit tcp any host (WAN IP) eq 8065
permit udp any host (WAN IP) eq 8065
permit tcp any host (WAN IP) eq 8066
permit udp any host (WAN IP) eq 8066
permit ip any any
ip access-list extended nat
permit ip any any
logging esm config
logging 10.34.1.7
access-list 50 permit (OUR WAN NETWORK) 0.0.2.255
access-list 100 permit ip any any
control-plane
mgcp profile default
line con 0
logging synchronous
line aux 0
line vty 0 4
logging synchronous
login local
transport input all
line vty 5 988
logging synchronous
login local
transport input all
scheduler allocate 20000 1000
endHardware is MV96340 Ethernet, address is 0022.551a.3b80 (bia 0022.551a.3b80)
Internet address is XX.XX.XXX.XXX/28
MTU 1500 bytes, BW 100000 Kbit/sec, DLY 100 usec,
reliability 255/255, txload 4/255, rxload 44/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Full-duplex, 100Mb/s, 100BaseTX/FX
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:00:00, output 00:00:00, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/1670/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 17259000 bits/sec, 1788 packets/sec
5 minute output rate 1728000 bits/sec, 1350 packets/sec
87395905 packets input, 766557199 bytes
Received 1332539 broadcasts (0 IP multicasts)
0 runts, 0 giants, 96 throttles
25676 input errors, 0 CRC, 0 frame, 0 overrun, 25676 ignored
0 watchdog
0 input packets with dribble condition detected
126794802 packets output, 2276449807 bytes, 0 underruns
0 output errors, 0 collisions, 0 interface resets
0 unknown protocol drops
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier
0 output buffer failures, 0 output buffers swapped out
FastEthernet0/1 is up, line protocol is up
Hardware is MV96340 Ethernet, address is 0022.551a.3b81 (bia 0022.551a.3b81)
MTU 1500 bytes, BW 100000 Kbit/sec, DLY 100 usec,
reliability 255/255, txload 42/255, rxload 4/255
Encapsulation 802.1Q Virtual LAN, Vlan ID 1., loopback not set
Keepalive set (10 sec)
Full-duplex, 100Mb/s, 100BaseTX/FX
ARP type: ARPA, ARP Timeout 04:00:00
Last input 00:00:00, output 00:00:00, output hang never
Last clearing of "show interface" counters never
Input queue: 0/75/6376/0 (size/max/drops/flushes); Total output drops: 0
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 1701000 bits/sec, 1317 packets/sec
5 minute output rate 16522000 bits/sec, 1712 packets/sec
129134088 packets input, 3150074778 bytes
Received 1290762 broadcasts (0 IP multicasts)
0 runts, 0 giants, 383 throttles
101275 input errors, 0 CRC, 0 frame, 0 overrun, 101275 ignored
0 watchdog
0 input packets with dribble condition detected
87242554 packets output, 1114685246 bytes, 0 underruns
0 output errors, 0 collisions, 1 interface resets
31588 unknown protocol drops
0 babbles, 0 late collision, 0 deferred
1 lost carrier, 0 no carrier
0 output buffer failures, 0 output buffers swapped out
Maybe you are looking for
-
Flash CS5 format to Flash CS3 Format
Hi. I'm using Flash CS5 and i need to save the animations i am making on Flash CS3 format. How can i do it?
-
Would someone PLEASE help me?!?
I was working on what amounted to a 4 hour slideshow. Months of work. I saved the project, but first emptied the trash as I've always done. This time it froze in mid save for a solid 12 minutes. Assuming that at the very least it would've saved my mo
-
I wanted to change the icon for my computer, but the info window says I am "read only" with no options below. How do I do this and why, if I am the admin., is it read only? Thanks
-
I use the apostropy key and up pops. Quick find (links only) I have tried everything, please help!!!
I have tried everything, nothing seems to work, I just updated to the most recent version hopping that the developers had attended to this issue. I have tried the about:config and made a true\false to shut off all quick search functionality but it do
-
Hi! What happens if I set <read-timeout-seconds> to some value for a read only bean, according to bea's docs the ejbLoad() is called initially when the EJB is created and afterwards, WebLogic Server calls ejbLoad() only at intervals defined by the re