Reloading after restoring IPod Classic

I did a restore on my Ipod Classic because it looked like it was getting full. I was going to delete some stuff off and reload only new content. Well when I restored it, now it will not even recognize my device so I can work with it. Not sure how to fix that.
Also some advice on manually managing files on my IPod classic. It seems to want to put everything on there that I buy, even though I have it on manually manage files.
Any Help out there would be appreciated.

That could be the result of a corrupt artwork cache db that is created during the initial sync of the iPod with your iTunes music library. Or it could be the result of corrupt artwork files. If you copied the artwork from online, you may want to try replacing it with a different version or using iTunes built in artwork fetch operation to get the correct artwork for the iPod.
So what I would do first is figure out if this is only happening with particular tracks and/or albums. If it is, replace the artwork for these tracks, and then resync your iPod with iTunes (assuming you have it set up to automatically sync. If not, you'll need to manually remove the old tracks and artwork from your iPod and add drag on the new ones).
Otherwise, another restore of the device in iTunes may be necessary.
B-rock

Similar Messages

After restoring iPod it stops syncing half way

After restoring iPod, it stops syncing while it is downloading music with an error message "Attempting to copy to the disk. iPod failed. The disc could not be read from or written to".
My music is less memory than what my iPod can hold.
What's up with this?
THX!

It's possible that your iPod's hard drive has started to fail. Take your iPod and place your right thumb on the centre SELECT button and your left on the top MENU button. Press down both thumbs for about 6 seconds until your iPod reboots. Immediately move your left thumb around to the rewind button |<< on the left and hold this down together with SELECT for a further 6 seconds. Your iPod should now switch into Diagnostic Boot mode. Press MENU for *Manual Test*, then select *IO > HardDrive > HDSMARTData* to reveal your stats. For comparison here are mine for my 2 year old 6th Generation Classic:
Retracts: 889
Reallocs: 12
Pending Sectors: 0
PowerOn Hours: 2202
Start/Stops: 894
Temp: Current 24c
Temp: Min 10c
Temp: Max 50c
Take a note of your results. When finished press *SELECT & MENU* for 6 seconds to reset the iPod again.
With modern disc drives sectors are no longer marked bad by a disc scan, if the SMART firmware detects a sector it has trouble accessing it will attempt to invisibly reallocate it to a spare area of the disc.
Note that I've only 12 remapped sectors and none pending. To help explain what the numbers mean here is an extract from the Wikipedia S.M.A.R.T. article:
*Reallocated Sectors Count*
Count of reallocated sectors. When the hard drive finds a read/write/verification error, it marks this sector as "reallocated" and transfers data to a special reserved area (spare area). This process is also known as remapping, and "reallocated" sectors are called remaps. This is why, on modern hard disks, "bad blocks" cannot be found while testing the surface – all bad blocks are hidden in reallocated sectors. However, as the number of reallocated sectors increases, the read/write speed tends to decrease. The raw value normally represents a count of the number of bad sectors that have been found and remapped. Thus, the higher the attribute value, the more sectors the drive has had to reallocate.
*Pending sector count*
Number of "unstable" sectors (waiting to be remapped, because of read errors). If an unstable sector is subsequently written or read successfully, this value is decreased and the sector is not remapped. Read errors on a sector will not remap the sector (since it might be readable later); instead, the drive firmware remembers that the sector needs to be remapped, and remaps it the next time it's written.
Large numbers of Reallocs or Pending Sectors would suggest your drive is failing and that you may need to repair or replace your iPod. Check your stats after another attempt to update your iPod. If the numbers increase that again points to hard drive failure. While it won't be good news at least you'll know it isn't some random software problem and you can decide what to do next.
tt2

TS1410 my movies disappeared and will not reload on my ipod classic, how do I fix it?

my movies disappeared and will not reload on my ipod classic, how do I fix it?

First try a Reset ( No Data will be Lost )
Press and hold the Sleep/Wake button and the Home button at the same time for at least Ten seconds... (But can take Longer)... until the Apple logo appears. Release the Buttons
If no joy... Try a Restore...
1: Connect the device to Your computer and open iTunes.
2: If the device appears in iTunes, select and click Restore on the Summary pane.
Restoring > http://support.apple.com/kb/HT1414
3: If the device doesn't appear in iTunes, try using the Steps in this article to force the device into Recovery Mode.
Make sure you have the Latest Version of iTunes (v11) Installed on your computer
iTunes free download from www.itunes.com/download
Note on Recovery Mode.
You may need to try this More than Once... Be sure to Follow ALL the Steps...
Once you have Recovered your Device...
Re-Sync your Content or Restore from the most Recent Backup...
Restore from Backup > http://support.apple.com/kb/ht1766

After restoring ipod nano it wont sync with itunes. states error 13019 occured

after restoring ipod nano it wont sync with itunes. states error 13019 occured

I seem to recall that another user has this problem and found that it was because of some corrupted music files they were trying to sync over.
Try syncing smaller bunches of tracks till you come upon the ones that cause the error. You should be able to find out which ones are causing the trouble this way.
The other user said they used something called MP3Diags. I cannot vouch for this software at all, I have never used it.
I did a quick search on "how to repair MP3 files on Mac" and also found this:
http://triq.net/articles/mp3-validator-mac-os-x
i

HT1339 after restoring ipod nano how do I get tunes back if they are in my music library

after restoring ipod nano how do I get tunes back if they are in my music librbary- thanks

Configure the music to sync back over to your device from under its Music configuration tab. If your library is smaller than the capacity available on your Nano, you can set it to sync your entire music library by enabling the Sync Entire Library option from under this tab. Otherwies, you'll have to select only certain artists, albums, playlists, and genres.
See this article for more information.
iTunes: Syncing media content to iOS devices and iPod
B-rock

Must Restore IPOD Classic Everytime I Synchronize

I had previously used this 80GB Ipod Classic with XP. I successfully moved to 64 bit Vista but I must do a hard reset, restore, then synchronize every time I add new music. I do have the latest software on the Ipod according to Itunes.
So I have to reload all songs whenever I do an update. If I don't follow these steps the computer crashes (blue screen) when it tries to synchronize. I look at the trouble shooting tips and they are exactly the steps I am already taking.
Any hints?

Well I fixed it. I put the iPod in disk mode and formatted it, then restored, and then synched it. I restarted the computer, made some changes in iTunes and resynched and it worked. Interestingly I couldn't format the iPod with Vista 32, Vista 64, or Windows XP. I had to use Ubuntu Linux to do the formatting.

Red circle with X through it after plugging ipod classic into computer?

My ipod classic is roughly 5 or 6 years old. It has worked great besides a few problems here and there. Today I plugged it into my computer and updated it on itunes. It had been a long time since I had done this. But generally the ipod works great! Shortly after unplugging the ipod (by ejecting it) a red cross with an "X" through it came on the screen after the music froze. PLEASE help!!! I use this everyday and it has tons of irreplaceable music on it!!! Thanks!

If a sad iPod icon or an exclamation point and folder icon appears on your iPod’s screen, or with sounds of clicking or HD whirring, it is usually the sign of a hard drive problem and you have the power to do something about it now. Your silver bullet of resolving your iPod issue – is to restore your iPod to factory settings.
http://docs.info.apple.com/article.html?artnum=60983
If you're having trouble, try these steps at different levels one at a time until the issue is resolved. These steps will often whip your iPod back into shape.
Make sure you do all the following “TRYs”
A. Try to wait 30 minutes while iPod is charging.
B. Try another FireWire or USB through Dock Connector cable.
C. Try another FireWire or USB port on your computer .
D. Try to disconnect all devices from your computer's FireWire and USB ports.
E. Try to download and install the latest version of iPod software and iTunes
http://www.apple.com/itunes/download/
For old and other versions of iPod updater for window you can get here
http://www.ipodwizard.net/showthread.php?t=7369
F. Try these five steps (known as the five Rs) and it would conquer most iPod issues.
http://www.apple.com/support/ipod/five_rs/
G. Try to put the iPod into Disk Mode if it fails to appear on the desktop
http://docs.info.apple.com/article.html?artnum=93651
If none of these steps address the issue, you may need to go to Intermediate level listed below in logical order. Check from the top of the lists to see if that is what keeping iPod from appearing on your computer in order for doing the Restore.
Intermediate Level
A. Try to connect your iPod with another computer with the iPod updater pre-installed.
B. Still can’t see your iPod, put it in Disk Mode and connect with a computer, instead of doing a Restore on iPod Updater. Go and format the iPod instead.
For Mac computer
1. Open the disk utility, hope your iPod appears there (left hand side), highlight it
2. Go to Tab “Partition”, click either “Delete” or “Partition”, if fails, skip this step and go to 3
3. Go to Tab “Erase” , choose Volume Format as “MAC OS Extended (Journaled), and click Erase, again if fails, skip it and go to 4
4. Same as step 3, but open the “Security Options....” and choose “Zero Out Data” before click Erase. It will take 1 to 2 hours to complete.
5. Eject your iPod and do a Reset
6. Open the iTunes 7 and click “Restore”
For Window computer
Go to folder “My Computer”
Hope you can see your iPod there and right click on the iPod
Choose “Format”. Ensure the settings are at “Default” and that “Quick Format” is not checked
Now select “Format”
Eject your iPod and do a Reset
Open the iTunes 7 and click “Restore”
In case you do not manage to do a “Format” on a window computer, try to use some 3rd party disk utility software, e.g.“HP USB Disk Storage Format Tool”.
http://discussions.apple.com/thread.jspa?threadID=501330&tstart=0
C. Windows users having trouble with their iPods should locate a Mac user. In many cases when an iPod won't show up on a PC that it will show up on the Mac. Then it can be restored. When the PC user returns to his computer the iPod will be recognized by the PC, reformatted for the PC, and usable again. By the way, it works in reverse too. A Mac user often can get his iPod back by connecting it to a PC and restoring it.
Tips
a. It does not matter whether the format is completed or not, the key is to erase (or partly) the corrupted firmware files on the Hard Drive of the iPod. After that, when the iPod re-connected with a computer, it will be recognized as an fresh external hard drive, it will show up on the iTunes 7.
b. It is not a difficult issue for a Mac user to find a window base computer, for a PC user, if they can’t find any Mac user, they can go to a nearest Apple Shop for a favor.
c. You may need to switch around the PC and Mac, try to do several attempts between “Format” and “Restore”
http://discussions.apple.com/thread.jspa?messageID=2364921&#2364921
Advance Level
A. Diagnostic mode solution
If you have tried trouble shooting your iPod to no avail after all the steps above, chances are your iPod has a hardware problem. The iPod's built-in Diagnostic Mode is a quick and easy way to determine if you have a "bad" iPod.
You need to restart your iPod before putting it into Diagnostic Mode. Check that your hold switch is off by sliding the switch away from the headphone jack. Toggle it on and off to be safe.
Press and hold the following combination of buttons simultaneously for approximately 10 seconds to reset the iPod.
iPod 1G to 3G: "Menu" and "Play/Pause"
iPod 4G+ (includes Photo, Nano, Video, and Mini): "Menu" and "Select"
The Apple logo will appear and you should feel the hard drive spinning up. Press and hold the following sequence of buttons:
iPod 1G to 3G: "REW", "FFW" and "Select"
iPod 4G+ (includes Photo, Nano, Video, and Mini): "Back" and "Select"
You will hear an audible chirp sound (3G models and higher) and the Apple logo should appear backwards. You are now in Diagnostic Mode. Navigate the list of tests using "REW" and "FFW". The scroll wheel will not function while in diagnostic mode. For further details on Diagnostic mode can be found at http://www.methodshop.com/mp3/ipodsupport/diagnosticmode/
Try to do the 5in1, HDD R/W and HDD scan tests. Some successful cases have been reported after the running the few tests under the Diagnostic mode. In case it does not work in your case, and the scan tests reports show some errors then it proves your iPod has a hardware problem and it needs a repairing service.
B. Format your iPod with a start disk
I have not tried this solution myself, I heard that there were few successful cases that the users managed to get their iPod (you must put your iPod in disk mode before connecting with a computer) mounted by the computer, which was booted by a system startup disk. For Mac, you can use the Disk Utility (on the Tiger OS system disk), for PC user, you can use the window OS system disk. Try to find a way to reformat your iPod, again it does not matter which format (FAT32, NTFS or HFS+) you choose, the key is to erase the corrupted system files on the iPod. Then eject your iPod and do a Reset to switch out from Disk Mode. Reboot your computer at the normal way, connect your iPod back with it, open the iPod updater, and hopefully your iPod will appear there for the Restore.
If none of these steps address the issue, your iPod may need to be repaired.
Consider setting up a mail-in repair for your iPod http://depot.info.apple.com/ipod/
Or visit your local Apple Retail Store http://www.apple.com/retail/
In case your iPod is no longer covered by the warranty and you want to find a second repairing company, you can try iPodResQ or ifixit at your own risk
http://www.ipodresq.com/index.php
http://www.ifixit.com/
Just in case that you are at the following situation
Your iPod warranty is expired
You don’t want to pay any service charges
You are prepared to buy a new one
You can’t accept the re-sell value of your broken iPod
Rather than leave your iPod as paper-weight or throw it away.
You can try the following, but again, only do it as your last resort and at your own risk.
Warning !!!! – It may or may not manage to solve your problem, and with a risk that you may further damage your iPod, which end up as an expensive paper weight or you need to pay more higher repairing cost. Therefore, please re-consider again whether you want to try the next level
Last Resort Level
1. . Disconnecting the Hard Drive and battery inside the iPod – Warning !! Your iPod warranty will be waived once you open the iPod.
In Hong Kong there are some electronic shops offering an iPod service for Sad iPod, the first thing they do is to open up the iPod’s case and disconnecting the battery and the Hard Drive from the main board of the iPod. Wait for 5-10 minutes and reconnecting them back. The reason behind which I can think of is to do a fully reset of a processor of the iPod. In case you want do it itself and you believe that you are good on fixing the electronics devices and have experience to deal with small bits of electronic parts, then you can read the following of how to open the iPod case for battery and HDD replacement (with Quicktimes)
http://eshop.macsales.com/tech_center/index.cfm?page=Video/directory.html
2.Press the reset button on the Hard Drive inside the iPod – Suggestion from Kill8joy
http://discussions.apple.com/thread.jspa?messageID=2438774#2438774
Have I tried these myself? No, I am afraid to do it myself as I am squeamish about tinkering inside electronic devices, I have few experiences that either I broke the parts (which are normally tiny or fragile) or failed to put the parts back to the main case. Therefore, I agree with suggestion to have it fixed by a Pro.
2. Do a search on Google and some topics on this discussion forum about “Sad iPod”
Exclamation point and folder and nothing else
Spank your iPod
http://www.youtube.com/watch?v=3ljPhrFUaOY
http://discussions.apple.com/thread.jspa?messageID=3597173#3597173
Exclamation point and folder and nothing else
http://discussions.apple.com/thread.jspa?messageID=2831962#2831962
What should I do with my iPod? Send it or keep it?
http://discussions.apple.com/thread.jspa?threadID=469080&tstart=0
Strange error on iPod (probably death)
http://discussions.apple.com/thread.jspa?threadID=435160&start=0&tstart=0
Sad Face on iPod for no apparent reason
http://discussions.apple.com/thread.jspa?threadID=336342&start=0&tstart=0
Meeting the Sad iPod icon
http://askpang.typepad.com/relevant_history/2004/11/meeting_the_sad.html#comment -10519524
Sad faced iPod, but my computer won’t recognize it?
http://discussions.apple.com/thread.jspa?messageID=2236095#2236095
iPod Photo: unhappy icon + warranty question
http://discussions.apple.com/thread.jspa?messageID=2233746#2233746
4th Gen iPod Users - are we all having the same problem?
http://discussions.apple.com/message.jspa?messageID=2235623#2235623
Low Battery, and clicking sounds
http://discussions.apple.com/thread.jspa?messageID=2237714#2237714
Sad faced iPod, but my computer won’t recognize it
http://discussions.apple.com/thread.jspa?messageID=2242018#2242018
Sad iPod solution
http://discussions.apple.com/thread.jspa?threadID=412033&tstart=0
Re: try to restore ipod and it says "can't mount ipod"
http://discussions.apple.com/thread.jspa?threadID=443659&tstart=30
iPod making clicking noise and is frozen
http://discussions.apple.com/thread.jspa?messageID=2420150#2420150
Cant put it into disk mode
http://discussions.apple.com/thread.jspa?messageID=3786084#3786084
I think my iPod just died its final death
http://discussions.apple.com/thread.jspa?messageID=3813051
Apple logo & monochrome battery stay
http://discussions.apple.com/thread.jspa?messageID=3827167#3827167
My iPod ism’t resetting and isn’t being read by my computer
http://discussions.apple.com/thread.jspa?messageID=4489387#4489387
I am not suggesting that you should follow as well, but just read them as your reference. You are the person to make the call.
Finally, I read a fair comments from dwb, regarding of slapping the back of the iPod multiple times
Quote “This has been discussed numerous times as a 'fix'. It does work, at least for a while. In fact I remember using the same basic trick to revive Seagate and Quantam drives back in the mid to late 1980's. Why these tiny hard drives go bad I don't know - could be the actuator gets stuck in place or misaligned. Could be the platter gets stuck or the motor gets stuck. 'Stiction' was a problem for drives back in the 80's. Unfortunately the fix can cause damage to the platter so we temporarily fix one problem by creating another. But I know of two instances where a little slap onto the table revived the iPods and they are still worked a year or more later.”UnQuote

Unknown Error 1430 when restoring iPod Classic

Hi,
Yesterday my ipod Classic froze, so I did a hard reset. However, it gave me a message that I needed to restore it, so I connected it to my Mac and attempted to restore.
Upon connecting it, iTunes detected it in recovery mode, but when trying to run the restore process, it stops after about 20% and gives me the following error message: “unknown error 1430 the iPod could not be restored”.
I have tried all the recommended steps on the Apple troubleshooting guide, including disconnecting and reconnecting, restarting computer, using different usb ports, different user accounts, and a different usb cable, reinstalling itunes and enabling/disabling disk use.
None of these steps have worked and I am out of ideas so I would appreciate any suggestions if other people have encountered this problem before.
Thanks in advance for any help.

some folks have been having some success with the 1417 and 1418 using eboncairn's technique:
eboncairn: iTunes7 & 5th gen iPod updating - is this possible solution? (winXP)

No matter what I do I cannot restore ipod classic. Ipod is corrupt with unknown error 1439.cannot restore the ipod Have tried all options but . can anyone help?

I recently bought a second-hand ipod classic. When connecting to itunes the message reads that the ipod is corrupt and needs to be restored to factory settings. However, this does not solve the issue and I get the message saying unable to restore, unknown error 1439. No matter what i have tried through apple support i get the same result. My computer runs Windows XP but I have also tried on my laptop which operates Vista and still no joy. Anyone able to solve this one?

Normally unknown error is due to timeout, cause by
connected to slow USB port at the front of the PC, or using USB Hubs - Better connect to the USB HUb at the back of the PC. (Some Laptop, has only one High Power -USB2.0 port
USB resource low, due to sharing of other USB devices - Disconnect all other USB devices when Restoring.
Winsocks conflict with iTunes - Disconnect Internet and Stop firewall and Antivirus, emails apps.
Your hardisk is dying, read this earlier post by tt2.
https://discussions.apple.com/message/17776595#17776595
This wont solve your problem. but is very helpful in troubleshooting.
It would also help, if you can state
Which version of iTunes are your running?
What is your iPod software version as shown in the iTunes summary page?
Have a nice day!

How to recover photos after restoring iPod touch?

Yesterday, there was an update for the iOS 6, I believe. When I pressed the update button, a message popped up saying that there was a problem with my iPod touch 4G and that I need to restore it. I had absolutely no idea why that message would pop up in the first place because my iPod was working just fine. But I couldn't update my iPod to the newest version if I didn't do what iTunes says... so I was about to restore my iPod, but then I was worried that all of my photos would disappear. So I decided to update my iOS later so that I could transfer all my files on to my computer. I then unplugged my iPod, and tried to turn it on but the home screen wouldn't pop - no matter what I did, all the screen showed was an itunes icon on top with a USB plug-in cord at the bottom. So I had no choice but to restore my iPod. The thing is, once I restored my iPod and all, my photos were all gone and I did not use iCloud as a back-up since a few months ago. All of my recent photos are now gone and I have no idea how to recover them. I've tried programs that aim to recover deleted photos, but they didn't work.
Is there a way to recover photos after restoring the iPod Touch?

Hello,
It is very important to backup your device to the computer before updating or restoring.
You can restore your device to a previous backup, all the photos that were there when you made the backup should return with it, but I'm afraid that any photos taken or saved after the last backup are unrecoverable.
I hope this helps.
~Lt. Leviathan

Restoring Apps after restoring iPod Touch

I recently restored my wife's iPod Touch and when I hooked it back up to her laptop iTunes kept asking me to purchase the January update. I kept telling it no seeing as we had already purchased the update along with the apps back in January. I read on the forum how it should be restored using the computer that the Touch was first synched to. This solved the problem seeing as how I was using the newest laptop to do the restore. The problem is that her original laptop is close to failing which means at some point I won't be able to restore the apps if the need arises again. Is there some way to transfer the January update files and apps over to her new computer so that next time I should be able to do a restore without having to use the original laptop?

The iPod touch January Software Upgrade can only be synced to iPod touch from the primary iTunes library. If the user is manually managing music and video on iPod, this is the computer where they first set up the iPod or first set it up after restoring the iPod. The "iPod touch App Pack 4A93.ipa" file can be copied from the computer where you purchased it to your primary iTunes library computer, and sync the iPod from there.
The file is located here:
Mac OS X:
~/Library/iTunes/Mobile Applications
Windows XP
C:\Documents and Settings\[user name]\Application Data\Apple Computer\iTunes\Mobile Applications\
Windows Vista:
C:\Users\[user name]\AppData\Roaming\\Apple Computer\iTunes\Mobile Applications\
Note: These locations are hidden by default in Windows. You can these locations by choosing "Show hidden files and folder" in the View tab of the Folder Options Control Panel.
Once you have copied the "iPod touch App Pack 4A93.ipa" file to the computer with your home library, make a new folder named Mobile Applications in the correct location, and place the "iPod touch App Pack 4A93.ipa" file there. Open iTunes and sync your iPod touch.

Syncing iPod After Restoring iPod to Original Settings

I am having a problem syncing my iPod with iTunes after restoring my iPod to it's original settings. I have a 20GB iPod with a click wheel that I recently restored to its original settings because the iPod was locking up. To complete the restore, I had to first force my iPod into disk mode, which allowed me to restore the iPod. After successfully restoring my iPod, I connected my iPod to my computer to sync it with iTunes and download my music library back to my iPod. At first, 3 to 4 songs/podcasts began to download, but then I received the following message:
"Windows-Delayed Write Failed. Windows was unable to save all the data for the file G:\iPod_Control\iTunes. The data has been lost. This error may be caused by a failure of your computer hardware or network connection. Please try to save this file elsewhere."
My OS is Microsoft XP. I went to the Micosoft webpage, but didn't find any helpful information. If anyone has any suggestions on how to solve this problem, your input would be apprecicated.

When you went to Microsoft, did you find/try the following document?
"Delayed Write Failed" error message when you manage files in Windows XP

Can't restore iPod classic.

I have an iPod classic serial number is not working for the support unfortunately. My iPod has frozen and apparently needs to be restored but unfortunately my iTunes won't recognise the iPod. I have updated to the new iTunes any help would be appreciated.

Hi Willldn123,
Welcome to the Support Communities! The article below will help you troubleshoot the issue you are having restoring your iPod classic:
iPod: Appears in Windows but not in iTunes
http://support.apple.com/kb/TS1363?viewlocale=en_US
Cheers,
- Judy

Can't restore iPod classic 60GB video. Cannot Allocate Memory - Disk Utility

Sorry if this has been asked before but I've been searching the boards and am yet to find a result.
I have an old iPod classic 60GB (video) which has a dodgy HDD. It was clicking and in a constant sad face/charging loop. I've managed to get it display "Please restore iPod" message and it is now being recognised by my macbook. I've tried to restore it via iTunes but when I try that I get an error message tht says "The iPod could not be restores because it is busy".
I've tried toformat the iPod using Disk Utility too but i get an error:
Disk Erase failed with the error:
POSIX reports: The operation couldn’t be completed. Cannot allocate memory
The oddest thing is that under disk utility my iPod drive is showing up as a 2TB drive:
All I'm realy trying to do is restore the iPod so I can try to recover some of the tracks using Disk Drill. Can anybody help?

See if you can find a window based PC and try to do a Restore there.

Same file copying up to 20x throughout songs, albums artists and genres, when syncing itunes to ipod. Restored ipod classic 3 times in lastest itunes with a new user but no difference. Anyone had this happening?

Just brought IPod Classic. When sync my iTunes library to iPod multiple files, up to 20times are copying in all music categories. Apple support got me restoring iPod then creating a whole new iTunes library in a new user on my computer. Did this, sync again, same problem. Anyone experienced this?

ps when syncing it jumps through steps 1 - 4 real fast, i seem to remeber iphone showing the number of tracks transferring and names, but i see nothing? then it sits on 5 saying "waiting for changes to be applied"

Reloading after restoring IPod Classic

Similar Messages

Maybe you are looking for