Remote access VPN to server from outside and server reach internet on the same time

Dear,
I have problem in my ASA 5515-X , when i make Remote access VPN to servers in inside zone the internet connection disconnected in the servers, or when i have internet in servers, the remote access cant reach servers.
the configuration for server as static NAT for each server, and the connection of VPN is to another public IP but in the same subnet of NAT ip.
server1 : 10.10.10.2 nat to 5.6.7.8
server2: 10.10.10.3 nat to 5.6.7.9
server3: 10.10.10.4 nat to 5.6.7.10
VPN connection to 5.6.7.12
is there any solution for this senario, remote vpn to servers and the same time the servers have internet readability for download updates .. etc

Hi,
So it seems that the problem is with lacking a NAT0 configuration
You could modify the below configuration to match your networks/IP addresses used. In the below configuration I presume that you have interfaces "inside" and "outside".
object network SERVER-NETWORK
subnet <server network address> <network mask>
object network VPN-POOL
subnet <vpn pool network address> <network mask>
nat (inside,outside) 1 source static SERVER-NETWORK SERVER-NETWORK destination static VPN-POOL VPN-POOL
Just insert the correct address related information and change the "object" and interface names if required.
This configuration will tell the ASA that no NAT will be performed for traffic between the VPN-POOL and SERVER-NETWORK. The NAT configuration is bidirectional. With this configuration the Static NAT configurations will continue to work for the servers Internet traffic and this NAT0 configuration will be applied only to the VPN Client traffic.
Hope this helps :)
- Jouni

Similar Messages

Cannot stream to iTunes and join wireless internet at the same time

I have a home network with an Airport Extreme base station, and Airport Express connected to my home stereo and to my existing wireless network in client mode. I receive internet via a wireless signal throughout my apartment building. My laptop receives the signal via the built-in airport express card. Neither the Airport Extreme or Air Express are connected directly to the internet, since I only have a wireless signal in the building (no ethernet).
With Airport turned on the wireless internet signal appears as a list of networks alongside my own network.
I can't seem to get the settings right such that I can join my Home network and be connected to the internet at the same time, since I have to join either one or the other from the drop down list. Therefore, I can't sream music wirelessly from my laptop to my airport express and be connected to the internet at the same time.
Is there any way around this?
Powerbook 17" Mac OS X (10.4.8)

Leosia, Welcome to the discussion area!
Your Mac only has a single radio receiver therefore it can only join one wireless network at a time.

Is there an issue with the hitachi hard drives in the MacBook Pro's ? Got a 15 inch and a 13 inch at the same time and both drives have failed in under two years. I have heard from a few other people with same issue.

Is there an issue with the hitachi hard drives in the MacBook Pro's ? Got a 15 inch and a 13 inch at the same time and both drives have failed in under two years. I have heard from a few other people with same issue. Other drive I have had have lasted at least 5 or more years.

there is a dylib you can put in the springboard if jailbroken but if not you have to find an apple store

I bought a bluetooth Bose speaker so I could listen to music from my imac in multiple rooms at the same time. I wanted to use BOTH my existing speakers using the headphone jack and add additional bluetooth speakers in other rooms, but the imac wants me to

I bought a bluetooth Bose speaker so I could listen to music from my imac in multiple rooms at the same time. I wanted to use BOTH my existing speakers using the headphone jack and add additional bluetooth speakers in other rooms, but the imac wants me to pick one or the other, is there a way to have both?

I asked same question
Any answers

Can I stream music from my itunes and play a movie at the same time?

I have an Apple TV hooked up to both an audio receiver and my TV with HDMI and optical cables. Can I stream a Netflix movie and also music from itunes (on a Macbook Pro) at the same time, so the audio and video content don't match?

No.

Labview runs CANBus and DNP3 software model at the same time

I have an ordinary computer which communicates with several DSPs (CANBus communiation) through Compact Rio. The physical connection is that the DSPs' CANBuses are connected together and connected into Compact Rio, then the Compact Rio is connected with a router through Ethernet, at the same time, the computer also connects with the Router through Ethernet. Based on this physical architecture, the computer can run CANBus software model on Labview to communiate with Compact Rio and DSPs.
As I know, the communication between the computer and the Compact Rio is not real time, and the communication between Compact Rio and DSPs can be real time, can you tell me if I get the right point?
Now we have another device named RTDS (communicate with outside through Enternet based on DNP3), and want to add RTDS into our system. I am not sure about the way to conduct the communiation. The main question is that we need to run Labview to communicate with DSPs through CANBus and RTDS through DNP3 at the same time, is that possible?
I proposed two possible ways to conduct communication, bt not sure if it is possible.
1. I proposed that I connect RTDS with the Router through Ethernet, and then the computer communicates with RTDS through the Router based on DNP3 and also keeps the communication with DSPs through Router, Compact Rio, CANBus and then DSPs. I am wondering if this kind of communication is available for Labview.
2. The second possible way I proposed is that I connect the RTDS with Compat Rio (CRio keeps connecting with DSPs through CANBus) through Ethernet, and then the computer communicates with DSPs through Router, Compact Rio and CANBus, and the computer communicates with RTDS through Router, Compact Rio and Ethernet. Also, the computer needs to run Labview with CANBus sofeware model and DNP3 software model at the same time. I am also not sure if it is possible.
The diagram of the communication system is shown in the attachments.
Attachments:
Commnucation system diagram.pdf ‏118 KB

To use Mail from multiple devices, your Mail Server needs to be using IMAP protocol (iCloud Mail uses that).
IMAP keeps the Master copies on the Server, not on the Mac the way most default POP Mail servers do.
To keep one Master Calendar, accessible from all devices, you need a web-accessible place to keep the Master Calendar. iCloud can do that.
¿Do you see a trend developing here?

How can I use a wireless printer and the internet at the same time?

Hi there, I just installed a wireless printer but to use it I have to click on the Airport icon and select the printer in the 'devices' list. This deselects my connection to my wireless modem. Is there any way I can print and look at the internet at the same time? This does not seem right to me, I print a lot of info from the net and don't want to spend time selecting and waiting for connection back and forth all the time.
Bo

I have a Linksys WAG54G2 wireless G router. This router has a Wireless Protected Setup button which I understood would initiate a search for wireless devices and aid setup but it seems to do nothing. I made the mistake of tryig to use the linksys installation disk to access a setup wizard and that just reset my entire network back to factory settings and it took me 4 hours to reconfig my system. Won't be touching that again. It all seems odd, the printer is compatible with the router as far as I can see but I don't know how to get the router to recognise the printer.
bo

Can't i use xml schema and oledb data connection at the same time?

Hello to all and thanks in advance.I use xml schema and oledb data connection at the same time and the problem is that when I try to export the xml, the outcome is not what i expect.Without the oledb connection everything is ok (just the schema) and the xml complies with the schema.
Can't i have both schema and oledb and the exported xml be as i want it?

You can use both at the same time, but not gor Internet access if that's what you're asking.
Now there is a thing called Link Aggregation, which combines a number of interfaces for speed/redundancy, but it really only works locally, and then only with ALL special equipment in the route, and most likely OSX Server involved.
Sorry.

I want to disable "restore previous session" and enable "History record" at the same time.

I want to disable "restore previous session" and enable "History record" at the same time.
Because I don't want others to access my account such as "Gmail", "Facebook". But I want firefox to record my browsing history.
What should I do?

I managed to remove the "Restore Previous Session" button from the home page by changing my default home page with this : www.google.com/firefox/ (the default home page from the previous versions of Firefox). It worked for me, I hope it works for you too.

No Airtunes and Internet at the same time

Hello,
I'm using an iPod Hi-Fi in combination with an Airport Express basestation.
My internet connextion goes through PPPoE. So I use the Airport Express in "Bridge mode" But...
iTunes won't find the (wireless) iPod Hi-Fi when PPPoE is winked "on" in the airport settings. When I wink PPPoE "off", iTunes do find the iPod Hi-Fi.
But without PPPoE I don't have an internet connexion.
So I can't use the internet and listen to Airtunes at the same time.
Does anyone have a solution?
Thanks!
Greetings,
Jarchall

I'd suspect that the Bonjour would not work properly if the wireless thinks the next hop down the wireless trail is the open internet instead of the Airport Express. PPPoE basically makes a tunnel from your computer to the ISP server. The PPPoE packets are wrapped in a special transport package the express probably can't get into unless there is some future specialized firmware update.
Unless you have some burning need for bridge mode I would configure the Airport Express to connect via PPPoE with the setup assistant.
-Alex

Can I save and open an attachemnt at the same time?

I want to be able to open an email with an attachement or attachments and click on the save button for the attachment(s), designate the location (folder) where they are to be saved - but also tell Mail to save the attachments then open them up on the desktop. Two operations in one. If you understand my request you understand what you have to do now - two separate steps. Save. Then find the saved files and open them.
OR
Open the attachment from the email which then downloads the file to your designated "all-purpose" location (not the ultimate location you'd want to save it). Then once you've seen it, you do the save thing with the original mail attachment and then have to go back and delete the file from the designated all-purpose download location.
This latter problem of having to delete unedited downloads manually could be solved with an option in Mail preferences to automatically delete unedited downloads in the "all-purpose" location after that same attachment had been downloaded to another specific location on your hard drive. This option for deleting unedited downloads does not exist, however.
But even if this step-saver option existed in the preferences, you still would not be able to tell your Mac to save a particular Mail email attachment to a particular folder AND open that attachment at the same time in one command.
That's what I want.
Maybe I want both. Save and open together plus the ability to automatically delete unedited attachment downloads in the "all-purpose" download file after the same attachment has been downloaded to another specific location on your hard drive.

with IOS 6 yes you will be able to do that

Can you run 3G and connect to wifi at the same time?

Is it possible to use the iPhone 5 to search 3G and connect to wifi at the same time? I'm trying to run my Apple TV but only have 3G that is run through my phone. I want to play Netflix using Apple TV run from 3G through my phone.

The phone and the ATV need to be on the same wireless network. You cannot communicate with the ATV using 3G on the phone

TS3280 How can i enable both paired bluetooth and ios keyboard input at the same time?

How can i enable both paired bluetooth and ios keyboard input at the same time?
This is needed for the app im working on. Need some user input via keypad as well as scanner input via a paired bluetooth scanner.

You probably should not be using a keyboard bluetooth profile for a scanner, I am not a developer for apple so do not know the location for you to find out the correct profile you should be using for an input device that is not a keyboard. Sorry,
I am sure if you navigate the apple developer site you will probaly finmd what you're looking for.
https://developer.apple.com

WRT160 doesn't seem to be able to support both PC and Apple devices on at the same time

we have 2 PCs, a macbook and an iphone. we use a cable modem with the WRT160 router. since thursday the 2 PCs can connect to the internet at the same time, but the mac then loses its connection as does the iphone. if the mac and iphone are connected, the minute we start up a PC, the mac and iphone lose their connection and can't reconnect. Apple couldn't help and said it was the router. Anyone have any ideas on what the problem is and how to fix it?

Open the router setup page and reduce the MTU to1400 and click save settings..Under the Wireless tab,Click on the subtab Advanced Wireless Settings...Change the Beacon Interval to 75,Change the Fragmentation Threshold to 2304,Change the RTS Threshold to 2304 and Click on Save Settings...Now,check..

Can Express 9 play and record multiple instruments at the same time?

I have logic express 9 and was told with my interface that I can play and record different instruments at the same time on Express 9. Is this true because I have spent a long time trying to figure out how.

Hi,
to record multiple Inputs at a time, open up the appropriate number of audio tracks. Now for each track, select the correct Input in the Channelstrip.
Now, ARM all these tracks for recording by clicking the little red R in the track header or channelstrip. Now if you hit record, all these tracks should record simultaneously their respective inputs.
All other existing tracks should playback while recording.
Fox

Remote access VPN to server from outside and server reach internet on the same time

Similar Messages

Maybe you are looking for