Remote control code for Sharp LC-32DV200E

Hi there!
i have just tried all codes for Sharp from BT Vision help page and it does not work. My telly is less than a year old, so it can't be an issue of old telly. Does anyone know any other codes (apart from those on |BT Vision list in help)? I will greatly appreciate some help here. Thanks in advance.

Yankee2 wrote:
Bought a new rev'8' sky remote control as the old one has hard-to-push buttons. I followed the instructions for programming the remote to my tv (LG 32LC2DB) but the codes supplied do not work on new remote. Checked code on 'old' remote (0206) and tried that - no luck. Red light does not blink when holding down 'select' and 'red button'. Switched everything off, removed batteries, turned back on and still nothing. New remote does work all Sky controls but not tv. Any suggestions would be appreciated. Try these codes as well 1293 1206.Then try the procedue below.Press TV (one flash)Hold select and red till remote flashes twice999SelectTVSelect and red till two flashesEnter codeSelect

Similar Messages

What is STB Remote Control code for the Magnavox 15MF400T/37 set?

Does anyone know or know where to find the correct remote control code for the 15MF400T/37 set?

If none of the codes worked, your only other option is to do a scan.
WHAT IF NONE OF THE CODES WORKED?
If none of the codes worked, try the following procedure. (As before, we will use the example of a TV. For other devices use the appropriate Device Key instead of the
TV
key in step 2 and 3.)
1. Turn on your TV.
2. Press and hold the TV key.
3. While holding down the TV key, press OK
4. Release both keys. The Device Keys will blink twice.
5. Press 9 - 2 - 2
6. Point the remote at the TV.
7. Press the play button
8. Press FF button . Every time you press the FF button the remote sends out a new power-off command to the TV. Keep pressing FF until the TV turns off.
9. When the TV turns off, you have found the right code. Press OK to store this code.
Note: There are over 300 TV and DVD codes. The most common codes are tried first, but you may still need to press FF over 300 times to find the right code. If you reach the end of the list of codes the entire remote will flash twice and return to normal operation. You can exit programming at any time by pressing EXIT
If you do this and it still doesnt work, then your tv and the verizon remote dont have a common code and it will not work with your tv.
====================================================================================
Error exists between keyboard and chair.

Can't find remote control code for Samsung BD-P2550

I am trying to configure my verizon fios remote to control my Samsung BD-P2550 using the DVD button on the remote. None of the suggested codes work nor does search for the code using the remote and the fast forward button for infinite attempts, PLEASE HELP!

joebingo,
Unfortunately the Verizon-provided universal remote will not work for all devices, particularly for advanced devices such as BR players. If you've already tried all the Samsung DVD codes and none of those work then it's most likely that there is not going to be a working code for this particular device.
However, you can try doing a manual code search by following the instructions here.
Regards,
Chris
Christian
Verizon Telecom
Fiber Solution Center
Notice: Content posted by Verizon employees is meant to be informational and does not supercede or change the Verizon Forums User Guidelines or Terms or Service, or your Customer Agreement Terms and Conditions or Plan.

Remote Code for Sharp

Can anyone please help, I had my youview box installed I need the code for my Sharp tv LC40LE511E K.

Thanks for your help, forget to say that I have tried all the codes for Sharp on the http://bt.custhelp.com/ci/fattach/get/2306219/1330618726/redirect/1 page, none worked. I had the same problem with The Sky box I have to send them the TV model and they got me the code. Was told by the Sky engineer that it is not a genuie Sharpe.

Remote Control settings for Markers

The user manual for Studio Pro 4 states that Remote Control settings for Markers will override all other settings while that part of the track or story plays.
This however, is not the case- In my project the track & story settings for Remote Control>Menu are actually overriding marker Remote Control>Menu settings, & I really need the marker functions to take precedence over other functions.
Any idea how I can make this happen?
Thanks!!
eric

As Jake said - I am not seeing this behaviour either.
If you clear all end jumps from chapter markers and place the markers into stories then you set the menu call for the story. This can be different to the track and depending on which you are playing the menu call for that item will take precedence.
Of course, if you really want to make it bullet proof then you could point the menu call to a script. Assuming that no matter which story you are in, or how you got to the marker in the track, the following script will always return you to a specific button on a menu for the marker that you have just played
mov GPRM0, SPRM7
Jump Menuname, [GPRM0]
SPRM7 is a system parameter that checks which marker has just played. The first line of the script loads the value of this into a memory slot called GPRM0. The second line operates a jump to your menu - I assume there is only one menu here - and using a conditional GPRM based button jump, the value of GPRM0 fills in the value of the button to go to. This saves writing out lines of code for each possible button.
If you have lots of menus then this script can be adapted very easily to cope with that, or you can set up other scripts to identify which menu you have come from so as you know which to go back to.
However, before any of this I would want to know why you are not getting the expected behaviour on our project - my guess is that there is going to be a menu call set into a chapter marker which is over-riding the track or story menu call. If you have end jumps on markers, or menu calls on markers, remove them.

Remote infrared codes for the Sony STR-DE675 receiver

Where can I find the remote infrared codes for the Sony STR-DE675 receiver? They are not in the Owner's Manual, nor on the Sony.com website. Thanks.GBP

If you were getting sound and no picture when you had the Wii hooked up to your surround sound receiver, your TV was probably on the wrong input. You would have needed to use the source or input button on your TV's remote and changed the input to the component 1 choice, since that is the port you stated you plugged the Wii into on the TV.
Your cable remote may not be programmed to work with the blu-ray player. However, I think you're misunderstanding the function of the buttons at the top of your remote labeled TV, Sat/Cab, VCR, etc. Your cable remote doesn't work like a Harmony remote. Pushing those buttons at the top of your cable remote are not like pushing the Watch TV or Watch DVD functions on a Harmony (meaning pushing them doesn't change the TV's input automatically). All those buttons at the top of the remote are for that you're describing are to tell the remote which components to control. For example, you are watching cable TV and just used the remote to change the channel but now you want to adjust the volume. You would have to hit the "TV" button on the cable remote to switch the remote from controlling the cable box to controlling the TV. Otherwise, you'd hit the volume controls over and over and nothing would happen b/c the remote would still think it was controlling the cable box. Only a Harmony remote (or similar universal remote) can change the TV's input with the click of a function button.
And to explain why one must change the TV's input when switching components, I always compare the process to the way a tube TV used to work for those that are new to the flat screen TVs. Think of the way your old TV probably worked - you had to have the TV on channel 3 for your VCR, 4 for cable, etc. The input changing is practically the same thing with just a few more steps, if that helps to make things any clearer. LOL
Nothing I post is an official statment of Best Buy or Geek Squad, it is only a helpful opinion!

How to maintain Import Processing: Control Code for the country India

Hi Gurus,
I need to maintain the Control Processing: Control Code for the country India in SPRO configuration.
Please tell me the path to maintain it.
Thanks,
Thiyagu

spro@Logistics - General@Material Master@Material IDs@Maintain PKWiUs
Regards,
Indranil

Remote control (media) for Pavilion G6S?

Can you recommend for a remote control (media) for Pavilion G6S?

Hi
> I didn't found any driver for the A500 anyway, even for Vista...
It looks like the A500 is very new on the market and I believe the drivers (Vista) will be released in the next time
You will have to wait a little bit
I think that the Vista driver would be compatible with the Win 7.
I have installed Win 7 on my notebook and most of the vista drivers are working.

How to backup new learned remote-control data for the IR-remote APP???

Hello @ all,
does anybody know a way to backup the new learned remote control on XPERIA Z Tablet?
I found a database under:
"system/vendor/etc/sony-ir-remote/db"
But after I've saved new learned remote controls the date and the size of these DB's
are the same as before. Therefore the IR-remote control APP dosn't save the new data
in these files.
Furthermore there isn't a button in the remote-control APP to backup new learned remote controls.
And I can't choose the remote control APP in the backup function APP from the XPERIA Z Tablet
to save the data. Also the backup with the Sony PC Companion Software dosn't save the learned
remote controls. Who develops such a dross mobile software?
Sorry SONY, but you have the most unpalatable support I've lived to see!
The first SONY support center refered me to another support center.
The mobile support center does not answer to my questions per mail.
Then I call the mobile support center. The answers were shallow and standard.
The support engineer want to ask the development and call back.
However, I am still waiting for promised recall.

I am facing the same problem.
I have spend a few days to configure and train my Sony tablet to configure for all my remotes such as aircon and lighting. I did a backup using the Sony companion to my PC. When my tablet was faulty and serviced. But the backup did not recover the IR remote settings and codes which I programmed previously. I also tried your backup restore app but it also does not save the configuration.
It is VERY IMPORTANT for me to backup the settings.
Please provide the folders and path of where the IR REMOTE settings and personal configuration and codes trained were kept so that I could back them up. Are these path protected area that required rooted access?
Hope that Sony could update the app to include backup of new trained codes and settings and in the meantime to provide a procedure of how to backup the setting and trained IR codes with or without rooting the device.

Need Sceptre TV Remote Control code(s) that work with VZ P265v3RC -- the '335' code does NOT

Recently upgraded my TV's in my house with new Sceptre 40" and 50" TV's - thank you WalMart. Purchased in September 2014. (new / current Sceptre TVs).
All of the Verizon printed, online, and other documentation for the P265V3 RC (model RC2655005/01B) for Sceptre shows to use code '335'. I have tried the '335' code on both of the TV's and no worky at all.
Following the 'Quick Setup Guide-Verizon FIOS remote' steps (paper/PDF instructions with RC Manual):
I can successfully enter the '335' code as outlned in step 4... and 'The RED LED will blink twice and then stay on'. occurs. So far, so good.
Step 5 states, "5. Press and release the <CH +> button repeatedly until the TV turns off......." This happens perfectly... I can press the <CH+>> button a few times, and indeed, my TV turns off.
Now, onto Step 6: "Test that the remote control is programmed for your TV"..... can't get Mute, A/V, other keys to activate /. be recognized - even though I'm followijng "press and hold that key. Release it as soon as it works"
Does anyone have a working code for Sceptre TV's ??? The Verizon '335' code doesn't work for me.
I need the 'best code' anyone has found that works with new Sceptre TV's.... the 335 code that VZ recommends... no worky.

Robertop,
have you tried the following? The info below is found here
Turn on your TV and the FiOS TV Set-Top Box.
Make sure you can see live TV.
Press and hold the OK and FiOS TV buttons together then release both buttons.
The red LED light blinks 2 times and then stays on.
Press and hold the Play button.
The remote control tries a new TV code every second.
The red LED light blinks each time a new code is sent.
When the TV turns off, release the Play button immediately.
NOTE: Some TVs may respond slower than others. If necessary, you can press the Ch+ and Ch- buttons to go forward or backward one TV code at a time.
Test your remote to ensure it is working properly:
- Turn on the TV by pressing the TV button on your FiOS TV remote.
- Press the Vol+ and Vol- buttons to ensure that you can control the volume.
- Press the Mute and A/V buttons to ensure they work.
If any of these buttons do not work, press and hold that button. Release the button as soon as it works.
If all the buttons work, press OK to this TV remote code.
The red LED light blinks 3 times and then turns off. Your remote control is now programmed.

Need to sign Lenovo in order to install our Remote Control app for our Customer - Help please!

Dear All,
Thank you for joining me into the Lenovo Community.
I am not certain if I have started the thread in the right place, if I have not, admins please help me transfer this thread where needed.
One of our Customers is going to purchase our Remote Control application, in order to access and remote control their Android Smartphones, from their Windows PCs (Windows Computers to access and remote control their Android phones). The Customer is using Lenovo as their smartphones (about 2000 of them).
However, our application needs to be signed by Lenovo in order to fully install and run on a Lenovo Android smartphone.
I do not have access to the Support department, nor to the Development department of Lenovo in China.
Is there a way that you would recommend I take, either by contacting Development directly, or Support, and where would that be? China or US?
Thank you in advance and I hope to hear from you soon.
kind regards,
Michael Chatzilias

Use the "auto search" feature of the remote to see get the code.
In the manual, it's under "WHAT IF NONE OF THE CODES WORKED"
Here's a summary:
program the TV, use code 922
Press Play
then Press Fast forward.
Keep pressing fast forward until your tv turns off (go slow, if you go to fast you can use rewind to go back a code).
when it turns off, the remote found the code, press OK to save it.

Remote control Tool for non-IT staff

Hi
We currently run ZENworks for Desktops v7 and have a requirement to
offer our financial systems team the ability to remote control users'
workstation without the need to use Console 1. All workstations are
currently Windows XP SP2 or SP3.
1. Are there any 3rd party/Cool tools that can be used to offer remote
control instead of using Console 1?
2. Do these tools require additional roles/rights?
Thank you.

You can use our DSRAZOR for eDirectory/NDS and NetWare product for this.
See the applets called "ZEN Remote Control / Remote View by User" and "ZEN
Remote Control / Remote View by Workstation" in the HelpDesk Examples
section of the DSRAZOR Console. The applets can be customized to your
needs - such as limiting which containers and/or which workstations are
shown, and allowing only remote control or only remote view (instead of
both). After any necessary modifications are made (we can show you how or
make the changes for you), save the applet as an EXE to distribute to the
people who will use it. Having the applet as an EXE means they will not
need ConsoleOne and they will not need the full DSRAZOR product either.
The example applet in the DSRAZOR Console is based on the user's own
privileges. If you do not want to grant these users their own privileges
for remote control / remote view, the applet can be modified to use our
optional Zero Privilege Helpdesk NLM. You would need one NetWare server to
run the Zero Privilege Helpdesk NLM. When you load the NLM you will specify
the name of a group (such as financial systems group). Then only the
members of that group will be able to successfully use the applet, which
they will have as a stand-alone EXE.
An evaluation of DSRAZOR is available from:
http://www.visualclick.com/?source=NVsupZen7r
"Donald Sparko" <[email protected]> wrote in message
news:eaK4m.1481$[email protected]..
> Hi
>
> We currently run ZENworks for Desktops v7 and have a requirement to
> offer our financial systems team the ability to remote control users'
> workstation without the need to use Console 1. All workstations are
> currently Windows XP SP2 or SP3.
>
> 1. Are there any 3rd party/Cool tools that can be used to offer remote
> control instead of using Console 1?
>
> 2. Do these tools require additional roles/rights?
>
> Thank you.
>
> --
>

Remote Control Wanted for a B540

Having problems finding my remote control since I sent my machine back for repair, so I'm asking if anyone has one for sale ?

hi Buckie,
If you need the remote control to use with the TV Tuner, you can get one on this website.
Hope this helps
Did someone help you today? Press the star on the left to thank them with a Kudo!
If you find a post helpful and it answers your question, please mark it as an "Accepted Solution"! This will help the rest of the Community with similar issues identify the verified solution and benefit from it.
Follow @LenovoForums on Twitter!

Desktop remote control software for iPhones?

Is there any software for desktop pc's to remote control an iPhone? I see numerous apps to control things from the iPhone, but I need one for the other way around.
We are looking to possibly deploy our own in-house app, but need to remote control the devices for troubleshooting/presentation purposes.
Any information is appreciated!

Not as of yet. The only thing that is remotely (no pun intended) close is remote file access, like apps such as Air Sharing.

Logik Remote control codes???

Hi,
just bought a 32 Logik television L32DIGB20.
I have tried all the codes for the remote and still not working.and no code in manual.
Anyone any ideas?

150 155 351
068 127 141
These are the known codes for Logik TVs for BT Vision.
You must make sure you follow the exact procedure for entering them.
Having said Logik TVs prove to be a giant headache for their users as folk can't get Sky remotes to work with them either.
Life | 1967 Plus Radio | 1000 Classical Hits | Kafka's World
Someone Solved Your Question?
Please let other members know by clicking on ’Mark as Accepted Solution’
Helpful Post?
If a post has been helpful, say thanks by clicking the ratings star.

Remote control code for Sharp LC-32DV200E

Similar Messages

Maybe you are looking for