Remote control not working on Touchsmart 610-1030uk

Had been working fine for long time. Now out of warranty. Battery fine. Indicator on remote and on PC (white LED on front panel) both show IR is working. Mouse and keyboard still work fine. I have tried uninstalling and reinstalling drivers for Microsoft eHome infrared transceiver but still can't get the machine to respond to remote control.
Any thoughts?
This question was solved.
View Solution.

Hello frrw. Sorry to waste your time. I changed the batteries and it works fine. It seems the red LED on the remote and the white LED on the PC that flashes when I press a button on the remote do not mean that the batteries are strong enough.
Meanwhile I have that recurring problem with blu-ray players. I will post a new question and maybe you can help.
Many thanks.

Similar Messages

BT Vision Box and Remote Control not working prope...

Hi,
Can anybody help me please?
I have a black BT Vision Box. The remote control had increasingly been sticking so tonight I just turned the power off tonight, left it off for 20 seconds and turned it back on.
It seemed to turn back on and reboot itself normally, it took the amount of time it normally does on a couple of occasions when it froze a few months back. However since I rebooted it approximately 3 hours ago it has been turning itself off and rebooting itself every 10 minutes or so. On one occasion when I turned it off on the front of the machine and left it for a few minutes, it turned itself on and started rebooting itself again.
The remote control is worse than when it was sticking, now there is a delay of up to 30 seconds after I press a button. Sometimes it does not work at all, when that happens it just becomes stuck and eventually reboots itself.
So far I have tried turning it off and on again, I have also tried rebooting the internet connection (which is working fine). I have tried pressing the off button on the actual box for 10 seconds and resetting it that way. I have put new batteries in the remote. Nothing has worked. If anyone can help me that would be great.
Solved!
Go to Solution.

Hi,
Unfortunately I can't get that far now.
I turned all TV related systems off last night in an effort to see if it would work properly today.
I came home from work and turned everything on. The system boots itself up until it gets to a grey screen that says "Nearly there..." with the BT logo in the bottom right corner. It stays like that for approximately one minute. Then it turns itself off and starts rebooting itself again.
I have tried pressing the on/off button on the front of the box and holding it in for 10 secs or so until the box turns itself off and reboots but the effect is still the same as above.
Do you have any other suggestions pleaase, aside from throwing it in the bin?

Win2k8 Remote Control Not Working With SRSS 4.2 + SRWC 2.2

Hi there.
I have an install of Windows Server 2008 (32bit) with SRSS 4.2 & SRWC 2.2 setup. I was previously on SRSS 4.1 & SRWC 2.1 and having the same issue I am having now, which to me tells me this problem is unresolved or i'm being a total muppet. (hopefully not the last one)
Windows Terminal Server environments has this awesome remote control feature where you can login to an RDP session which is already active and take control of the session while the end user is still logged in.With Server 2003 this works perfectly fine- it's brilliant. WIth 2008 it is a nightmare. It works for a split second and then closes off. The end users session also gets locked out (not logged out) and they have to put their windows credentials in to carry on working again.
Now... I can remote control users who are logging in via Remote Desktop on Windows XP/Vista etc.. but I can't with the Sun Ray Sessions. Does the SRWC 2.2 fully compatible with RDP 6.1 or is there any information anyone can give me to point me in the right direction of resolving this issue, like I said.. Win 2k3- Works like a dream....
Any help would be greatly appreciated.
Regards
- Joe.

I just realised I hadn't posted the logs from SRSS Server with the issues. I have just tried on another WIN2K8 Server which wasn't configured by myself or my company and the same symptoms occurred. See logs below:
Oct 1 10:58:06 ESL-SOLARIS-SPARE kiosk:uttsc[4095]: [ID 702911 user.notice] /opt/SUNWuttsc/bin/uttsc[104]: 4116 Abort
Oct 1 10:58:06 ESL-SOLARIS-SPARE Sun Ray Connector proxy:[4117]: [ID 855542 user.error] Child closed socket prematurely, session shutdown
Oct 1 10:58:06 ESL-SOLARIS-SPARE kiosk:uttsc[4123]: [ID 702911 user.error] /opt/SUNWuttsc/bin/uttsc exited with error code 134 - exiting
Oct 1 10:58:06 ESL-SOLARIS-SPARE kioskcrit: [ID 702911 user.notice] Info: critical application uttsc (pid=3902) exited with non zero status: 134
Oct 1 10:58:06 ESL-SOLARIS-SPARE kioskcritd[3752]: [ID 422571 user.info] Info: a critical application has exited.
Oct 1 10:58:06 ESL-SOLARIS-SPARE kioskcritd[3752]: [ID 126805 user.info] Terminating Kiosk Primary Session ( pid=3902 )
Oct 1 10:58:06 ESL-SOLARIS-SPARE kioskcritd[3752]: [ID 308018 user.info] kioskcritd stopped
Oct 1 10:58:07 ESL-SOLARIS-SPARE utauthd: [ID 794400 user.info] SessionManager0 NOTICE: EMPTY: ACTIVE session
Oct 1 10:58:15 ESL-SOLARIS-SPARE kiosk:utkioskconfig:refresh[4381]: [ID 702911 user.info] Enabled Kiosk Mode for display ':2'
Oct 1 10:58:15 ESL-SOLARIS-SPARE dtlogin[4274]: [ID 118685 user.info] pam_sunray_amgh::[DPY=2] AMGH_SUMMARY: token=pseudo.00144fb78760, username=, AMGH_Done?=NO(Local Session), Details=AMGH is not configured., AMGH_Target=*NONE*
Oct 1 10:58:15 ESL-SOLARIS-SPARE dtlogin[4274]: [ID 976841 user.info] pam_kiosk: pam_sm_authenticate: Initiating Kiosk session with user utku2
Oct 1 10:58:15 ESL-SOLARIS-SPARE kioskcritd[4420]: [ID 190395 user.info] kioskcritd started
Oct 1 10:58:57 ESL-SOLARIS-SPARE Sun Ray Connector proxy:[4612]: [ID 855542 user.error] Child closed socket prematurely, session shutdown
Anyone able to help me out?

XFI-64 Bit Driver, remote control not work

I have just installed the 64Bit drivers for my X-fi Fatality. The sound works however the 'sound console' that plugs into the dri've bay at the front of my pc does not seem to be working. I press start on the remote control and nothing happens. The X-fi volume icon does not appear in the system tray. When I boot up the 32 bit version of windows all is well and i can use the remote control and all of its functions. Can anyone help as this is now very frustrating.

Originally Posted by MiLoCzE
Hi men, if you will use remote control, you must install ECUP_PCVTAPP_LB_3_40_21 . :-)
What is " ECUP_PCVTAPP_LB_3_40_21 " ?
I searched on the internet and all I could find about it is that it's a virus? Can you tell me something more about that file ?
http://www.pc-face.com/exe-file-erro...exe-fix-22694/

Audigy 2 ZS Platinum - Remote Control not work

hello all.. Sorry for beating a dead horse. My installation on a P4 3.0 ghz machine of the Audigy 2 was flawless. All hardware diagnostics that have been run have been successful. Everything works. I updated all drivers. Everything is functional on the unit.....but...the remote control doesn't work.
When I got to setup the remote control and it asks to select a transmitter (rm-500) from a drop down list, it shows rm-500. but it the drop down list for the receiver is BLANK? I've tried several suggestions from the forum but it still doesn't work.
Have I missed something or is it quite possibly just a dud unit that I have to take back.
thanks for all suggestions and ideas...
sony

OK, let's see, you have a device that is still under warranty. You properly installed said device. You put batteries in the remote but it does not work no matter what you try. It seems to me that you have only one option and you mentioned it in the penultimate sentence in your post.
Hope it's not a long dri've.:smileyvery-happy:
Richard
Message Edited by sf3454 on 03-3-2005 03:28 AM

Remote control not working

The remote control for one of my TVs is not working. We inserted new batteries and also checked all cable connections. We tried one of the other remote controls and the TV responded. How do we get a new remote control ?? We tried calling ATT but could not get through.
Thank you in advance
Mojo612

The original remote is not controlling the TV or the STB or both?
Try pressing the att button, then see how it works.
The two TVS are the same? They both use the same IR.

The remote controls stopped working

I bought with an official Apple dealer the new i Pod Shuffle (generation 3) to use during my bike rides. After the first ride the remote controls stopped working and the voice over feature spontaneously started repeating the songs title. As well the volume control stopped working altogether. I didn't have time to return the Shuffle after only a week so I disable the voice over feature and keep on using my Shuffle with no volume adjustment, fast forward etc ….
After a visit to the Apple website I saw that several owners complained about this problem and assumed Apple would know about it and be ready to offer a fast solution. So picked an official Service Center as close as possible from my location.
First shock the Service Center was dirty, the paint obviously several decades old and faded, the light kept to the minimum.
Second shock not Tech on duty to check something as simple as a headsets. I realized there was no way to have a fast resolution to my problem. The Shuffle will be send to a regional repair center, I could have save the trip and just go to an Apple dealer. What the use to have Service Centers if they don't provide service?
Now when a product is returned, after 25 days of ownership (can't say use), a product designed by a company with the reputation of Apple you expect some kind of sign that the company is sorry, stands behind it's product and will do all possible to solve the problem. WRONG.
Third shock. The person who took my Shuffle obviously never saw a Shuffle generation 3 before or even knew it existed. She explained over and over that I may (but it sounded more like I will) be charge for the repair. Even asked me to pay upfront a basic fee to cover the time of a Tech checking on the product. And that the Tech will give me a quote if I am to be charged. Furthermore She found tons of reasons why eventually I would be charged to repair the product, however no technical person ever checked on the product. Well I guess only users read messages on Apple website not employees of Apple.
So what now? I am suppose to receive an E-mail in 24 hours to 5 working days, in which I'll be explained the result of the Tech investigation.
I guess most owners of Apple products have a better experience with the Customer Service or where the reputation of Apple being a “cool” company comes from? But based on my experience it looks like Apple's products and Apple's Customer Service may not meet Apple's reputation or customer's expectations. Or am I asking for too much?

I seriously doubt you were at an Apple Store and you were not dealing with Apple employees. You were dealing with a 3rd party shop that does work on Apple products.
Don't know where you are located but you could contact Customer Service at Apple and complain but they are somewhat limited it dealing with a 3rd party company. But they will at least have you complaint on file. Or you could attempt to find an actual Apple Store and take your Shuffle there. Or you could try one of the workarounds listed on the threads here.

Remote control stopped working on MacBook Pro

I have two MacBokk Pros (2008 and 2011), with two remote controls that worked fine and interchangeable until about a week ago. Now both remotes work only on the older one of our computers, but not on the newer one. I have looked into the Security prefs panel, "Disable Infrared Receiver" is unchecked, "this computer will work with any available remote control" is shown underneath - everything look like it was before.
Holding "Menu" and "Fast Forward" to pair the remote produces no results after 5 seconds or more.
I also did the the "iSight test" mentioned elsewhere in this forum, the batteries in both remotes are fine and sending a signal.
That leads me to suspect there might be a problem with the infrared receiver. But is that a hardware or software issue and what should be done next, considering that I'm about 200 miles from the next Apple store?

Thank you! Yes, I've seen this troubleshooting page and followed those suggestion, that's where I also found the remote control battery test mentioned above.
Product ID: 0x8242
Vendor ID: 0x05ac (Apple Inc.)
Version: 0.16
Speed: Up to 1.5 Mb/sec
Manufacturer: Apple Computer, Inc.
Location ID: 0xfd110000 / 3
Current Available (mA): 500
Current Required (mA): 100
The only difference here is a "3" in the Location ID where your's shows a "2"
UPDATE: The SMC Reset tip worked! Thank you!!!

Remote does not work correctly after update

Hello,
the subject explain it already:
After upgrading to 2.3 the apple remote does not work correctly anymore:
I need to push the buttons twice, and than atv is only reacting sometimes.
Any ideas?
BR
Frank

Same problem here. First, I thought it was the Apple remote's battery. I replaced that and the problem persisted. I then used my digital video camera to verify that the remote was actually transmitting infrared, it was. In frustration, I tapped the buttons rapidly while pointing at the Apple TV. The Apple TV responded. The next button press it failed to respond. I tapped rapidly again and it finally responded. After many many rapid presses, while pointing directly at the Apple TV, it finally began responding to all presses. Once I'd regained control (I thought) I unpaired and re-paired the remote. Everything continued to work. At that time I also saw that I could "learn" another remote. So, I set up my Samsung TV remote. Sweet. Until the Apple TV went into screensaver mode again and I had to go through the same rapid button press sequence... with either the Apple remote or my learned Samsung remote. Conclusion, since the Apple TV will become fully responsive after the rapid button press sequence, it is certainly a software related problem.

Remote Control does work with Sylvania Color TV/DVD Model 6520FDF

I cannot get the remote control to work the volume on a Sylvania Color TV/DVD Model 6520FDF TV. Can anybody help me?

Have you tried the scan mode to scan for the proper code?
TV/DVD combo units are notoriously hard to program to universal remotes. So if you did a scan and none of them worked then the likelihood is that the remote just will not work with that unit. If you have not tried a scan, here is the instructions to do so.
WHAT IF NONE OF THE CODES WORKED?
If none of the codes worked, try the following procedure. (As before, we will use the example of a TV. For other devices use the appropriate Device Key instead of the TV key in step 2 and 3.) 1. Turn on your TV.
2. Press and hold the TV key.
3. While holding down the TV key, press OK. 4. Release both keys. The Device Keys will blink twice.5. Press 9 - 2 - 2. 6. Point the remote at the TV.
7. Press PLAY.8. Press FASTFORWARD (FF). Every time you press FF the remote sends out a new power-off command to the TV. Keep pressing FF until the TV turns off. (You can press REWIND to go back.) 9. When the TV turns off, you have found the right code. Press OK to store this code. Note: There are over 300 TV and DVD codes. The most common codes are tried first, but you may still need to press over 300 times to find the right code. If you reach the end of the list of codes the entire remote will flash twice and return to normal operation. You can exit programming at any time by pressing Exit.
Message Edited by spacedebrismark on 05-17-2009 02:26 PM
====================================================================================
Error exists between keyboard and chair.

Apple remote contra not working with Lion

I installed Lion and my littele apple remote control does not work anymore with my mac book pro.
Is there any solution for that?
Thanks

It's not working for me either.
I know that Lion doesn't include Front Row, but the remote is not working with any other application (ex. iTunes).
Please somebody help us!

My remote will not work with my TV @nywhere card, Please help.

I have just installed my TV @nywhere card and it works great. I have all the cables plugged in right but I can't get the remote control to work. I even tried a new battery. I'm running windows XP pro. Any Suggestions?

What's wrong with it is it's broken. The power button is broken. The dock port may be broken. The battery may have reached the end of its useful life.
Make an appointment at the genius bar of your local Apple Store and have it checked out. There are no words that will fix failed or broken hardware other than "here is my credit card"...
An out of warranty replacement for an iPhone 4 is only $149.

SSRS 2008 R2 Calendar Control not working and report not refreshing on pressing enter in Chrome.

SSRS 2008 R2 Calendar Control not working and report not refreshing on pressing enter in Chrome.

SSRS reports are always best viewed in IE and the report result what you see in IE always will not be same and consistent in thirdy party browswers.
So consider using IE as workaround.
Also please refer:
https://social.msdn.microsoft.com/Forums/vstudio/en-US/2188de10-cff9-4e24-b14f-da5121f1c4a4/ssrs-calender-control-not-visible-in-chorme-on-server?forum=sqlreportingservices
Workaround here:
http://www.rajbandi.net/Fixing-SSRS-Report-Viewer-control-date-picker-in-Google-chrome/
-Vaibhav Chaudhari

JDBC control not work after upgrade application from workshop 8.1 to 9.2.3

Hi,
We upgraded application from workshop 8.1 to 9.2.3. After that, the JDBC control not work any more. We got the following exception:
java.sql.SQLException: The transaction is no longer active - status: 'Committed'. No further JDBC access is allowed within this transaction.
at weblogic.jdbc.wrapper.JTSConnection.checkIfRolledBack(JTSConnection.java:192)
at weblogic.jdbc.wrapper.JTSConnection.checkConnection(JTSConnection.java:202)
at weblogic.jdbc.wrapper.Connection.preInvocationHandler(Connection.java:87)
at weblogic.jdbc.wrapper.Connection.getMetaData(Connection.java:435)
at org.apache.beehive.controls.system.jdbc.parser.SqlStatement.createPreparedStatement(SqlStatement.java:128)
at org.apache.beehive.controls.system.jdbc.JdbcControlImpl.execPreparedStatement(JdbcControlImpl.java:272)
at com.bea.wlw.runtime.core.control.internal.JdbcControlImpl.invoke(JdbcControlImpl.java:136)
at controls.SecurityBean.getUpdateDocPermission(SecurityBean.java:598)
at security.SecurityManagerImpl.getUpdateDocPermission(SecurityManagerImpl.java:110)
at security.SecurityManagerBean.getUpdateDocPermission(SecurityManagerBean.java:509)
The control that throw the exception has "transactionattribute" annotation added automatically by upgrade wizard during upgrading. Related classed are as follows:
@ControlInterface()
public interface SecurityManager
@TransactionAttribute(TransactionAttributeType.REQUIRED)
boolean getUpdateDocPermission(java.lang.String userId);
@ControlImplementation()
public class SecurityManagerImpl implements SecurityManager, Serializable
* @common:control
@org.apache.beehive.controls.api.bean.Control()
private controls.Security security;
static final long serialVersionUID = 1L;
* @common:operation
public boolean getUpdateDocPermission(String userId)
if ( security.getUpdateDocPermission(userId) > 0) {
return true;
else
return false;
@ControlExtension()
@JdbcControl.ConnectionDataSource(jndiName = "EventDesk")
public interface Security extends JdbcControl
static final long serialVersionUID = 1L;
* @jc:sql statement="select r.updateDoc from document_user u ,document_role r where u.login={userId} and u.roleId=r.roleId;"
@JdbcControl.SQL(statement = "select r.updateDoc from document_user u ,document_role r where u.login={userId} and u.roleId=r.roleId;")
int getUpdateDocPermission(String userId);
Thanks for your help

Hi. The issue is a level or two above JDBC. I suggest
opening an official support case. It's probably a
WLW issue.
Joe

My Apple TV remote is not working.

My Apple TV remote is not working. It was fine this morning, but now ATV is not responding to it. It still access iTunes on my Mac so I don't think it's a battery issue. The white light flashes on ATV, but nothing happens. I have restarted ATV several times from the mains, but no change. Please help!

Hey Punkmonk1,
Thanks for the question. I understand that you are experiencing issues with your Apple TV remote. The following resource may provide a solution:
Apple TV (2nd and 3rd generation): Resolve issues with Apple Remote
http://support.apple.com/kb/TS5157
Thanks,
Matt M.

Remote control not working on Touchsmart 610-1030uk

Similar Messages

Maybe you are looking for