Remote Desktop Shortcuts won't work in FULLSCREEN mode

Hello,
I found lots of
shortcuts won’t work during remote desktop connection between Win7 64 host (home premium) to Win 7 64 guest (professional):
Include:
ALP+PAGE UP/PAGE DOWN
CTRL + ALT + ±
In order to make them work I need to exit full screen mode of remote desktop first (can be done with CTRL+ALT+BREAK)
Is there any fix?
Bob

Hi，
Have you check the "Local Resources" under Remote Desktop Connection "properties",? just as screen shot below:
You can also test this issue with On-screen keyboard, check if issue persists.
Yolanda Zhu
TechNet Community Support

Similar Messages

Remote Desktop Connection won't work from Leopard to Windows XP

Hi, folks:
I'm unable to connect to my work XP computer via my home iMac (Leopard 10.5.7) using Microsoft's Remote Desktop Connection for Mac. The XP settings are correct, I'm connected on my work network VPN, and I don't believe I have any router firewalls causing the problem --- the reason I know this is because I also have an MacBook running Tiger (10.4.11) and it has been connecting to my work PC without any problems. So, this must be a Leopard firewall setting?
As far as that goes, on my iMac I've got Screen Sharing, Remote Login and Internet Sharing turned on. Again, work network VPN is on.
I'm getting this error from Remote Desktop Connection:
"The Mac cannot connect to the Windows-based computer
This problem can occur if:
- The Windows-based computer is not set up to accept remote connections
- The Windows-based computer is not turned on
- The Mac, or the Windows-based computer is experiencing network problems
Try connecting to the Windows-based computer again, or contact your administrator"
Anyone know of a fix? I'd greatly appreciate it!
Thanks.

What Firewall setting do you have on your Mac? Try setting it to allow all connections. At least as an experiment.
Do you have any Proxies set in System Preferences -> Network -> Advanced -> Proxies? If yes, then is it possible that "Bypass" list is not covering the XP system.

"remote desktop connection has stopped working" When printing from remote desktop connection

I have been having a issue when using a windows 7 machine. I have Remote Desktop to a session on Windows2008 R2, I am using the local printer resources to redirect the printing. However everytime i try to print it crashes the remote desktop application.
Gives me "remote desktop connection has stopped working." I have 4 other computers connected and printing with no issues what so ever. This only happens when i print. It does print by the way just the application crashes.
-I have also updated the printer drivers to newest possible thru the manufactorer website. The printer is a Brother MFC-8890DW. Windows 2008 R2 is up to date for the RDS server. 3 other machines are able to Remote in and print. The user is able to print using
diffrent machines just not the Windows 7 machine.

Hi,
Happy to hear that you resolved your issue. For another issue which you are facing here trying to provide some suggestion.
As you have commented that you are facing issue with second screen resolution on wide screen. The setting which I am suggesting can only applies when you are using multi-monitor Remote Desktop connections. If you are making Connections using a single
monitor do not use this setting.
So for this you can try to apply “Limit maximum display resolution” setting in group policy, where you can mention the width & height for the screen to display. The setting can be applied on below mentioned
path.
Computer Configuration\Policies\Administrative Templates\Windows Components\Remote Desktop Services\Remote Desktop Session Host\Remote Session Environment
Meanwhile sharing article with you for more information.
Remote Session Environment
http://technet.microsoft.com/en-us/library/ee791847(v=ws.10).aspx
Hope it helps!
Thanks.

Zoom keyboard shortcut won't work with "Italian Pro" keyboard, Zoom keyboard shortcut won't work with "Italian Pro" keyboard

Hi everyone,
I am trying to get to the bottom of this mystery. "Italian Pro" is the keyboard I use almost all the time, and for some reason this zoom shortcut won't work. Another user assured me that "cmd-+" is the shortcut also in that keyboard. Mine doesn't work though. I have tried removing the keyboard and reapplying it. I've tried to use it on different browsers and different applications. I've even created another user and logged into that, installing the keyboard there. Nothing has worked, so can anyone suggest anything? What do I do next? (I know it doesn't seem like much but the issue really interferes with the flow of my things) Thank you!
Joachim

enggopah wrote:
"Italian Pro" is the keyboard I use almost all the time
Is Italian Pro
a. the keyboard, or,
b. the keyboard layout
you use all the time?
for some reason this zoom shortcut won't work.
What zoom are you talking about?
The View > Zoom In command in Safari or Preview?
The Universal Access > Zoom In function?
The Zoom In command in some other app, eg, InDesign?
Some other Zoom entirely?
Another user assured me that "cmd-+" is the shortcut also in that keyboard.
If we're talking about (b) and (1), then this 'other user' (his initials wouldn't be TG, would it?) was right. My keyboard is US QWERTY, and, if I switch to Italian Pro, ⌘-+ works. However, as the 'other user' has already told you, to do ⌘-+ with the Italian Pro keylayout on the US QWERTY keyboard, you have to press simultaneously the keys labelled ⌘ and ] -- as you can easily see in Keyboard Viewer.

Illustrator CS2 shortcuts won't work

I recently purchased Leopard, and now my Illustrator CS2 shortcuts won't work. I tried to create a new set of shortcuts but that doesn't work either. I can't even open a new document without going to the menu.
I would appreciate if anybody know a way of fixing this, as I don't want to purchase CS3 just yet.

Lisa - CS2 also has activation and de-activation in the same way as CS3 does. What it does not have is the un-installers. The installation-rules are the very same for CS2 as for CS3. You cna isntall as many times as you want, you can only activate on two-machines imultaneously and only use it on one machine at the time.
The first thing to do if shortcuts stop working is to delete your preferences and start from defaults. Re-installning is the very last resort and very seldom needed in my experience. an dif you need to reinstall, you need to first get rid of old settings and other files that belong to the application or they will still be there and behavior of application still be the same.

Undo keyboard shortcut won't work

I have quite a bizaare problem - the keyboard shortcut for undo will work after I restart my computer, but after awhile, it simply stops working. I am thus forced to click on Edit->Undo every time I want to undo something. Once the shortcut stops working, it applies to all applications. I have not been able to identify any "trigger" which causes it to stop working. I've tried to "Restore defaults" in the Keyboard shortcuts tab under the Keyboards menu, but this didn't have any effect. Any ideas?

enggopah wrote:
"Italian Pro" is the keyboard I use almost all the time
Is Italian Pro
a. the keyboard, or,
b. the keyboard layout
you use all the time?
for some reason this zoom shortcut won't work.
What zoom are you talking about?
The View > Zoom In command in Safari or Preview?
The Universal Access > Zoom In function?
The Zoom In command in some other app, eg, InDesign?
Some other Zoom entirely?
Another user assured me that "cmd-+" is the shortcut also in that keyboard.
If we're talking about (b) and (1), then this 'other user' (his initials wouldn't be TG, would it?) was right. My keyboard is US QWERTY, and, if I switch to Italian Pro, ⌘-+ works. However, as the 'other user' has already told you, to do ⌘-+ with the Italian Pro keylayout on the US QWERTY keyboard, you have to press simultaneously the keys labelled ⌘ and ] -- as you can easily see in Keyboard Viewer.

I've just updated itunes and it has disappeared from my PC- the previous shortcut won't work and it can't locate on my file search- this is the second time this has happened when updating itunes- APPLE you're going donw the tubes slowly but surely..

I've just updated itunes and it has disappeared from my PC- the previous shortcut won't work and it can't locate on my file search- this is the second time this has happened when updating itunes- APPLE you seem to be going down the tubes slowly but surely..

its not apple going "down the tubes" its that you have windows junk. These opinion best left at apple.com/feedback
you need to completely uninstall itunes and all components
see these for help
http://support.apple.com/kb/HT1925
http://support.apple.com/kb/HT1923
Peace, Clyde

Blackberry Desktop Manager won't work with Curve 9310

Can anyone help me troubleshoot why the Blackberry Desktop Manager won't work when I plug my Balckberry Curve 9310 into the USB port. The program freezes and shuts down. If I try to use the device switch wizard I get this message "Fatal Error has occured while updating your device's software. Please try again." I had to purchase a new Blackberry because my provider doesn't work in my new location so I bought StraightTalk Blackberry because I use it for business and I am familar with the phone. I am desparate to get my connections loaded onto my new phone. Help!

Hi and Welcome to the Community!
I suggest this thread:
http://supportforums.blackberry.com/t5/Desktop-Software-for-PC/Cleanly-quot-Starting-Over-quot-with-...
It starts with a process for cleanly starting over, and there is some discussion, and there is also a post (15) with links to older Desktop Software versions, if those are needed. Note that this is not, by any means, guaranteed to work...but it has worked for many to resolve issues they are having.
Good luck!
Occam's Razor nearly always applies when troubleshooting technology issues!
If anyone has been helpful to you, please show your appreciation by clicking the button inside of their post. Please click here and read, along with the threads to which it links, for helpful information to guide you as you proceed. I always recommend that you treat your BlackBerry like any other computing device, including using a regular backup schedule...click here for an article with instructions.
Join our BBM Channels
BSCF General Channel
PIN: C0001B7B4 Display/Scan Bar Code
Knowledge Base Updates
PIN: C0005A9AA Display/Scan Bar Code

Input Textfields not working in fullscreen mode

Input Textfields not working in fullscreen mode any one help me.

Quotes from Adobe:
"Users cannot enter text in text input fields while in full-screen mode. All keyboard input and key-related ActionScript is disabled while in full-screen mode, with the exception of the keyboard shortcuts that take the viewer out of full-screen mode."
Check with this article to know more: http://www.adobe.com/devnet/flashplayer/articles/full_screen_mode.html

WRT54G v4 won't work in PPPoE mode...

WRT54G v4 won't work in PPPoE mode...
For the past few years, I've had my WRT54G v4 set up to run in PPPoE mode. My Siemens Speedstream 5200 is set to run in Bridge Mode. It's worked fine for a long time. If I ever ran into a problem, I could always simply reset both, re-do all the settings, and it'd be fine.
Today I come home from work, it's not working at all. I reset the settings, redo everything, still not working. I do this a few times. It repeatedly just won't connect to anything. The DSL modem activity lights are flashing, everything is normal, the Status page in my Linksys setup all reads fine (it's connecting through the modem like it should, acquiring an IP address, etc). So, I decide I'm gonna reset the modem and try bypassing the Linksys.
That turns out to work just fine.
So I reset the Linksys, hook my PC back up to the Linksys, and everything is fine. But here's the rub...
If I try to bridge the modem and put the Linksys in PPPoE mode, it simply stops working. If I put it back into DHCP mode and reset the DSL modem, it still won't work. Once it enters PPPoE mode, the Linksys simply stops working as it should. Nothing besides a reset will make it start working.
Any suggestions/explanations as to what would cause this? I'm completely baffled, personally. I'm running the DSL modem in it's normal state and the Linksys in DHCP but I really prefer it the other way. I just can't figure out why it isn't working.
So, to sum up:
1. Connection is fine when going straight through the DSL modem.
2. Connection is fine when routed through the Linksys into the DSL modem with the Linksys in DHCP mode.
3. Once DSL modem is set to Bridge Mode and Linksys to PPPoE, I lose internet connectivity. No DNS, nothing.
4. Even if I change the settings back to DHCP, it still will not work. I must manually reset the router's settings using the reset button, doing the same with the DSL modem.
Any suggestions? I've tried everything I can possibly think of.

You need to Upgrade the Router's firmware in order to get the connection work again with PPPoE...
Download 2.95 MB...Once the Firmware has been downloaded you need to unzip the firmware file, it will unzip 3 files, you need the .bin file...
Open an Internet Explorer browser page.In the address bar type - 192.168.1.1
Leave the username blank & in password use admin in lower case...
Click on the 'Administration' tab- Then click on the 'Firmware Upgrade' sub tab- Here click on 'Browse' and browse the .bin firmware file and click on "Upgrade"...
Wait for few seconds until it shows that "Upgrade is successful" After the firmware upgrade, click on "Reboot" and you will be returned back to the same page OR it will say "Page cannot be displayed".
Press and hold the reset button for 30 seconds...Release the reset button...Unplug the power cable from your router, wait for 30 seconds and re-connect the power cable...Now re-configure your router...

Visualizer with update not working in fullscreen mode

I just did the most recent itunes download and now the visualizer won't go into fullscreen mode! Even if I press command + F. Please help!

hello niunaiwehua, you will probably get more helpful answers, when you post your question in a forum specialised on flash development like [http://forums.adobe.com/community/flash]. thank you

REMOTE DESKTOP SHORTCUT KEYS

Since updating Remote Desktop 8.0.14 las night 12th March, most of my shortcut keys are not working - the Option key seems to be the issue - any ideas

Hi,
Please try latest version 8.0.15 and check result.
https://itunes.apple.com/in/app/microsoft-remote-desktop/id715768417?mt=12
Thanks.
Dharmesh Solanki
Please remember to mark the replies as answers if they help and unmark them if they provide no help. If you have feedback for TechNet Support, contact [email protected]

Miracle : remote desktop app that actually works perfectly

New guy here...not new to Android, but very new to the TT (aren't we all, I guess). Loving it...this is the computer I've waited 35 years for. Thanks, Toshiba! As many of us know, one of the big problems w Android is the highly variable...and frequently low...quality of apps (even paid apps). I tend to buy a lot of apps just looking for one which will really get the job done. And frequently come away feeling suckered yet again. So when I went looking for a remote desktop app to run my MacBook from inside my TT (for intensive tasks like REAL spreadsheets) I was prepared for the worst (full-featured remote desktop is a pretty sophisticated task) but, surprisingly, nailed it on the first try. I don't usually plug products, but in case your needs are like mine, here goes: Splashtop Remote Desktop HD. Awesome. Stable. Fast. Ten bucks. If I recall correctly there are versions for both Mac and Win desktops. On my home wireless network there is zero perceptible lag. It claims to work over the intertubes, too, but I haven't tried that yet, and I'm prepared to learn that there the lag might be annoying. The ability to bring up your desktop on your TT, run any program there or fetch any file (I use Wuala on both Mac and TT to facilitate that) is pretty awesome. I intend to make the TT my primary business travel machine, which always raises the threat of those "oops...I don't have the file (or the software) I need on this machine" moments. That's what remote desktops are for. But lately, seeing how well Splashtop works, I find myself using it around the house, too. For instance I've given up on trying to find an Android spreadsheet app that isn't lame and slooooow (even Google Docs doesn't do it for me); now I just connect to my Mac, fire up Excel, and get the job done right. If you sometimes need (or just want) the power of a desktop machine on your TT, drop a dime and get this. You can thank me later. You should also pick up a stylus if you don't already have one (I'm loving the Kensington), because desktop controls rendered on a ten-inch screen can be kind of tiny to poke accurately with your fat fingers. Enjoy! P.s.: Nope, I'm not affiliated with Splashtop. I just really appreciate stuff that works well, is powerful, and gives good value. Plus I'm just tickled to be running my desktop on my TT with no compromises.

I have looked at Splashtop, but before getting it, I wonder if it is better than the LogMeIn Ignition that comes (although a trial) with the TT. I use LogMeIn a lot with desktops and laptops, but it can be very laggy depending onP the internet connection. I would welcome your views as I intend to use one of these apps a lot!

MS Remote Desktop and MySQL stopped working

Hi,
I used to have MS Remote Dektop Client on my Mac, and access my PC regularly. I also accessed the MySQL server on the same machine from the Mac. I use AirPort Express.
Then, I left for a two month travel during which I used the AirPort on other connections (but I THINK I created another profile for those).
Long story short, since I came back I haven't been able to connect to either. I thought it was a problem on the PC, but my friend could connect fine from his PC (however, the PC is on the same network than mine).
All the settings in windows seems to be ok, but it still won't work. Any guesses?

Since RDC is not an Apple product, you'll get better response if you use a forum dedicated to Microsoft's Mac products such as <http://groups.google.com/groups/dir?sel=33607053> rather than an Apple forum.
Be sure to search the forum first in case someone has already had a similar question answered. You'll get your answer faster this way. Post your question in the forum if you don't find anything that helps you

Remote Desktop Connection has stopped working

Using Build 10041. Occurs on 2 separate systems I have when trying to use Remote Desktop Connection through a 2012 R2 RDS Gateway. I am able to connect to the remote systems and access the environment for a short period prior to MSTSC.EXE
crashing. "A problem caused the program to stop working correctly. Windows will close the program and notify you if a solution is available."
Eventlog has the following:
Log Name:      Application
Source:        Application Error
Date:          3/25/2015 2:50:21 PM
Event ID:      1000
Task Category: (100)
Level:         Error
Keywords:      Classic
User:          N/A
Description:
Faulting application name: mstsc.exe, version: 10.0.10041.0, time stamp: 0x5503b1a7
Faulting module name: mstscax.dll, version: 10.0.10041.0, time stamp: 0x5503b315
Exception code: 0xc0000005
Fault offset: 0x000000000046d78c
Faulting process id: 0x2164
Faulting application start time: 0x01d06734abf028a0
Faulting application path: C:\WINDOWS\system32\mstsc.exe
Faulting module path: C:\WINDOWS\system32\mstscax.dll
Report Id: 2b084e37-d328-11e4-ab40-7c7a9191e005
Faulting package full name:
Faulting package-relative application ID:
JW

Tried this with no luck. I have the same issue as the OP. It was failing on 10041 and is still failing with an AV on 10049. See below event log entry after registering mstscax.dll and rebooting. Still failing.
Log Name:      Application
Source:        Application Error
Date:          4/11/2015 12:18:21
Event ID:      1000
Task Category: (100)
Level:         Error
Keywords:      Classic
User:          N/A
Computer:      Chuck1
Description:
Faulting application name: mstsc.exe, version: 10.0.10049.0, time stamp: 0x55137bff
Faulting module name: mstscax.dll, version: 10.0.10049.0, time stamp: 0x55137d3f
Exception code: 0xc0000005
Fault offset: 0x000000000046d74c
Faulting process id: 0x1870
Faulting application start time: 0x01d0748c29e55e06
Faulting application path: C:\WINDOWS\system32\mstsc.exe
Faulting module path: C:\WINDOWS\system32\mstscax.dll
Report Id: 83921b7c-e07f-11e4-960f-40f02f7ad3a4
Faulting package full name:
Faulting package-relative application ID:
Event Xml:
<Event xmlns="http://schemas.microsoft.com/win/2004/08/events/event">
<System>
    <Provider Name="Application Error" />
    <EventID Qualifiers="0">1000</EventID>
    <Level>2</Level>
    <Task>100</Task>
    <Keywords>0x80000000000000</Keywords>
    <TimeCreated SystemTime="2015-04-11T19:18:21.000000000Z" />
    <EventRecordID>73626</EventRecordID>
    <Channel>Application</Channel>
    <Computer>Chuck1</Computer>
    <Security />
</System>
<EventData>
    <Data>mstsc.exe</Data>
    <Data>10.0.10049.0</Data>
    <Data>55137bff</Data>
    <Data>mstscax.dll</Data>
    <Data>10.0.10049.0</Data>
    <Data>55137d3f</Data>
    <Data>c0000005</Data>
    <Data>000000000046d74c</Data>
    <Data>1870</Data>
    <Data>01d0748c29e55e06</Data>
    <Data>C:\WINDOWS\system32\mstsc.exe</Data>
    <Data>C:\WINDOWS\system32\mstscax.dll</Data>
    <Data>83921b7c-e07f-11e4-960f-40f02f7ad3a4</Data>
    <Data>
    </Data>
    <Data>
    </Data>
</EventData>
</Event>

Remote Desktop Shortcuts won't work in FULLSCREEN mode

Similar Messages

Maybe you are looking for