Remote gateway is not responding error message

When I try to connect through Quick VPN installed on PC with XP SP3, it shows "remote gateway is not responding".
I am using following setting
router configuration:
=========================
#1. Basic Setup, set MTU to manual and to 1492.
#2. In the Firewall - General Tab , DoS Prevention must be disabled, and everything else unchecked.
#3. VPV - VPN Client access, enter user name and password.
#4. VPN - VPN Passthrough - All Enabled.
#5. VPN - IPSec VPN -did not touch and here are the enteries:
section VPN Tunnel:
vpn tunnel: disabled
name: blank
NAT-Traversal: disabled
Local secure group:
type: IP adress
IP address: 192.168.1.0
Mask: 255.255.255.255
Remote secure group:
type: IP adress
IP address: 0.0.0.0
Mask: 255.255.255.255
Remote secure Gateway:
type: IP adress
IP address: 0.0.0.0
Key Management:
did not change anything either
Here is the VPN log on the router:
041 [Sat 21:18:40] listening for IKE messages
042 [Sat 21:18:40] forgetting secrets
043 [Sat 21:18:40] loading secrets from "/etc/ipsec.secrets"
Home side I am using Dlink router DI-624 and IPs are 192.168.0.1 and IPsec on the router is enabled.
On office side IP is 192.168.1.1 with linksys WRV200 router.
Please let me know what changes should I do on the router etc.? Thanks for your help.
Message Edited by JD001 on 09-15-2008 08:38 PM

All of them are running with Win XP SP2 at work. NAT-Traversal: is Disabled. DMZ is enabled. Thanks

Similar Messages

RVO42G VPN Error - The Remote Gateway is Not Responding. Do you want to wait?

I have followed the instructions @
https://supportforums.cisco.com/docs/DOC-29399, but continue to receive the error message The remote gateway is not responding. Do you want to wait?
According to the RV042G, it shows the connection was made and the status is set to "online" for the user, but choosing to wait does not connect and the error returns eventually requiring you to select "no" to waiting.
Thanks for your help.
Clinton

Thanks for reaching out Abhishek.
I am trying to setup a Client to Gateway VPN so I can utilize the 50 available tunnels. I have setup a Group VPN with user accounts associated with it. I have installed the Cisco QuickVPN client on Windows 7 and Windows 8 clients and have attempted to login. I have followed the instructions that Cisco posted @ https://supportforums.cisco.com/docs/DOC-29399, but cannot connect a remote client successfully. I recieve the error:
The remote gateway is not responding. Do you want to wait?
Looking at the VPN log on the RV042G, I see:
Jun 26 11:27:45 2013    VPN Log (qknips0): deleting connection
Jun 26 11:26:51 2013    VPN Log loading secrets from '/etc/ipsec.d/ipsec.secrets'
Jun 26 11:26:51 2013    VPN Log forgetting secrets
Jun 26 11:26:51 2013    VPN Log listening for IKE messages
Jun 26 11:26:51 2013    VPN Log added connection description (qknips0)
Jun 26 11:25:41 2013    VPN Log loading secrets from '/etc/ipsec.d/ipsec.secrets'
Jun 26 11:25:41 2013    VPN Log forgetting secrets
Jun 26 11:25:41 2013    VPN Log listening for IKE messages
Jun 26 11:25:41 2013    VPN Log added connection description (grpips0)
Jun 26 11:25:41 2013    VPN Log (grpips0): deleting connection
I don't know what else to do to get the QuickVPN client working so I can take advantage of the VPN service and 50 tunnels.
Thanks.

Firefox is very slow to respond when opening and nearly always stops responding altogether even refusing to react to Task Manager "End Program@ command. The "not responding@ error message also comes up during navigation on line.

Firefox is very slow to respond when opening and nearly always stops responding altogether, even refusing to react to the Task Manager "End Program" command. The "not responding" error message also comes up during navigation on line. Several attempt have to be made to get on line. A loss of stability seems to be endemic at the moment.

Try following the instructions here: [[Firefox hangs]]

"Firefox is already running but is not responding" error message and recent firefox update

"Firefox is already running but is not responding" error message is continuously popping up after the recent firefox update. I have nearly exhausted every possible solution to the problem as seen from the support page for this error message. I know someone who has the same issue on their computer and it also started right after the recent big update. Does the update have anything to do with this reoccurring issue? Is anyone else having this problem? Any other ideas on how to fix it? It would be great to get some help.

From what I have been reading from other posts on this forum, the
issue may be caused by the clear history settings.
Press the '''<Alt>''' or '''<F10>''' key to bring up the tool bar.
Followed by;
Windows; '''Tools > Options'''
Linux; '''Edit > Preferences'''
Mac; ''application name'' '''> Preferences'''
Then '''Privacy'''.
The button next to '''History''', select '''Use Custom Settings'''.
At the bottom of the page, turn on '''Clear History When Firefox Closes.'''
At the far right, press the '''Settings''' button. Turn on ONLY '''Cache''' and
'''Form And Search History''' leaving the others off.
This is not a cure but will make it easier if Firefox locks up.
'''https://support.mozilla.org/questions/997866?esab=a&s=&r=1&as=s''' {web link}

RV220W reports the remote gateway is not responding.

Hi, I've just set-up one of the RV220W VPN solutions.
This worked fine for a while, but now it reports the remote gateway is not responding.
Other clients can connect, but not the computer I'm using at home.
Logfile reports:
2011/08/31 21:10:31 [STATUS]Success to connect.
2011/08/31 21:10:31 [STATUS]Tunnel is configured. Ping test is about to start.
2011/08/31 21:10:31 [STATUS]Verifying Network...
2011/08/31 21:10:37 [WARNING]Failed to ping remote VPN Router!
2011/08/31 21:10:40 [WARNING]Failed to ping remote VPN Router!
2011/08/31 21:10:43 [WARNING]Failed to ping remote VPN Router!
2011/08/31 21:10:46 [WARNING]Failed to ping remote VPN Router!
2011/08/31 21:10:49 [WARNING]Failed to ping remote VPN Router!
2011/08/31 21:11:01 [WARNING]Ping was blocked, which can be caused by an unexpected disconnect.
2011/08/31 21:11:03 [STATUS]Disconnecting...
2011/08/31 21:11:07 [STATUS]Success to disconnect.
2011/08/31 21:15:07 [STATUS]OS Version: Windows 7
2011/08/31 21:15:07 [STATUS]Windows Firewall Domain Profile Settings: ON
2011/08/31 21:15:07 [STATUS]Windows Firewall Private Profile Settings: ON
2011/08/31 21:15:07 [STATUS]Windows Firewall Private Profile Settings: ON
2011/08/31 21:15:07 [STATUS]One network interface detected with IP address 192.168.2.2
2011/08/31 21:15:07 [STATUS]Connecting...
2011/08/31 21:15:07 [DEBUG]Input VPN Server Address = 81.167.1.1
2011/08/31 21:15:07 [STATUS]Connecting to remote gateway with IP address: 81.167.1.1
2011/08/31 21:15:07 [WARNING]Server's certificate doesn't exist on your local computer.
2011/08/31 21:15:09 [STATUS]Remote gateway was reached by https ...
2011/08/31 21:15:09 [STATUS]Provisioning...
2011/08/31 21:15:17 [STATUS]Success to connect.
2011/08/31 21:15:17 [STATUS]Tunnel is configured. Ping test is about to start.
2011/08/31 21:15:17 [STATUS]Verifying Network...
2011/08/31 21:15:22 [WARNING]Failed to ping remote VPN Router!
2011/08/31 21:15:25 [WARNING]Failed to ping remote VPN Router!
2011/08/31 21:15:28 [WARNING]Failed to ping remote VPN Router!
2011/08/31 21:15:31 [WARNING]Failed to ping remote VPN Router!
2011/08/31 21:15:34 [WARNING]Failed to ping remote VPN Router!
2011/08/31 21:15:46 [WARNING]Ping was blocked, which can be caused by an unexpected disconnect.
2011/08/31 21:16:49 [STATUS]Disconnecting...
2011/08/31 21:16:53 [STATUS]Success to disconnect.
I've tried the most common stuff.
Enabling ICMP, checked that remote administration runs on port 443, changed MTU to 1400 manually, It allows fragmented packages too.
Checked that IKE and IPSec services are running.
I've also tried both with windows firewall ON and OFF.
A collegue of mine had the same problem in the same timeframe as me, but after a while - he suddently was able to connect.
I still can't!!
Firmware Version:        1.0.2.4
Anyone got a fix for this?
Edit: IP is not real.

Ok, so I had a chat with Cisco - and it seems like the setup on the RV220W was done correctly and was working fine.
Showed me a few things that could come in handy checking out when running diag on the quickvpn.
I disabled all antivirus realtime checks, opened 443 and 500 inbound to my computer - checked that the QuickVPN.exe had an exception in the windows firewall, and that the firewall was enabled.
Also checked that the services was set tu Auto and Started.
Rebooted computer, and I was able to connect!
Now I'm working my way back to the setup I had, to figure out what went wrong in the first place.

I use google with firefox, everytime i open firefox and begin browsing or go to check my mail i get a firefox not responding error message on top left of screen. How do i get rid of this?

Question
I use google with firefox, everytime i open firefox and begin browsing or go to check my mail i get a firefox not responding error message on top left of screen. How do i get rid of this?

Hi,
Please check if this happens in [https://support.mozilla.com/en-US/kb/Safe%20Mode Safe Mode.]
[http://kb.mozillazine.org/Problematic_extensions Problematic Extensions]
[https://support.mozilla.com/en-US/kb/Troubleshooting%20extensions%20and%20themes Troubleshooting Extensions and Themes]
[http://support.mozilla.com/en-US/kb/Uninstalling+add-ons Uninstalling Add-ons]
[http://kb.mozillazine.org/Uninstalling_toolbars Uninstalling Toolbars]

Not Responding Error Message

Good Afternoon,
I am currently editing text to match timing of auido in my Captivate 6 slides. I am continually running into a "Not Responding" error message. Please inquire with sugeestions on how to stop this.
Already tried:
- Rebooting Captivate
- Rebooting System
- Working just out of Captivate with no other programs running
Thank you!

Thank you for your continued help.
I had not yet tried clearing the cache - after I did (twice) the end result was still the same.
Refreshing the preferences folder sounds like something we are willing to try, but I was wondering if there were step by step directions for this process in Captivate 6? This link does not allude to any direction within Captivate 6. .http://helpx.adobe.com/captivate/kb/troubleshoot-unexpected-behavior-captivate-4.html
Thanks.

Keep getting "not responding" error message as DW hangs

I have had the following problem consistently used DW 12.1, as well as the version that was with CS 5.5. And I am almost sure it has something to do with the html or other code on my pages, but I thought a DW guru might help.
Basics First: DW 12.1 with the subscription. 64 bit Window 7.
Files that I am editing will periodically freeze, and then I get the "not responding" message above the menu bar. It freezes for 10 to 30 seconds (IT FEELS LIKE 10 TO 30 HOURS) and then starts working again.
Of course it only seems to happen when I'm on a roll making many duplicate mundane edits and then BOOM... can't do anything except shoot laser eye daggers at the screen and try to prevent myself from hyperventilating.
Here's the thing. I work on many sites; and this generally only happens on the site of my main client. I work off o local copies of the site, but I inherited them and they are massively full of bloat code, scripts, etc. I would not be surprised in the least if DW is trying to run or access some of this and this is the cause.
I turned off the "Display external files" option; are there other options I should try? It really is the absolute most annoying thing in my life right now (we should all be so lucky) and I'm hoping you might have a way to fix it.
I'd be happy to post code, but this page is a typical example where I might get the error 10 times in a 30 minutes while working on it...
http://www.healthfirst.com/acls-kit.html
Thanks!

Retard, (I know that sounds hilarious, but I don't know your name - no offense please! )
Like you said, if this happens only primarily on one of the many sites, it generally comes down to the type of code on that site.
And after looking at the URL you posted, seems like that page uses a lot of external references - JS and CSS.
Especially the last few lines:
<script type="text/javascript" src="http://njcdn.worldsecuresystems.com/CatalystScripts/Java_OnlineShopping.js?vs=b1763.r38875 7"></script>
<script type="text/javascript" src="http://njcdn.worldsecuresystems.com/CatalystScripts/Java_Cookies.js?vs=b1763.r388757"></script>
<script type="text/javascript" src="http://njcdn.worldsecuresystems.com/CatalystScripts/Java_Box.js?vs=b1763.r388757"></script>
Also, a couple CSS, JS references in the <head> section.
'Display External Files' only disables showing external files - but still loads them.
Can you try removing the external references and try working with the webpage in DW for a few minutes to see if the same problem persists? If it does, we know what was causing your issue.
Also, run your site through W3 validator to check and resolve errors: http://validator.w3.org/check?uri=http%3A%2F%2Fwww.healthfirst.com%2Facls-kit.html&charset =%28detect+automatically%29&doctype=Inline&group=0
Let us know how it goes.
Good luck.
-ST

"Insufficient Bandwidth Problem" and "Did not respond" error messages

I am getting 3 error messages when I try to video chat using isight and ichat with my son's PC (which does video chat with my husband's PC) I have not been able to video chat although I can instant message with my son's PC.
1. It says insufficient bandwidth"
2. It says "starting" for a LONG time, and never finishes.
3. Or they request a chat with me and I get a "Did not respond" message.
I have tried connecting with both my .mac account and my aim name inside of iChat
So far, I have:
1. Changed Quicktime streaming to 1mbps Cable
2. Reinstalled Quicktime 7.0.1, erasing 7.0.3
3. Made an ichat AV entry under Firewall, listing TCP etc ports for network entry, using numbers from previous posts
4. Firewall is off
Since video chat works between my son's computer and my husband's, I doubt that it is our cable company or my son's. My son can also video chat with friends in his area. They are using msn or aim. However I have not been able to establish a connection using ichat.
If there are no other fixes, then I will probably have to call Apple tomorrow for a return on the isight that I just purchased. Too bad, because the Los Angeles Times this morning said that iChatAV image quality is superior to even Skype's new product 2.0 for Windows. At this time Skype does not have a cross platform product. Is that the problem with iChatAV, it really only works with other Macs?
Please advise if there is anything else that I can do to correct the problem. I have used an apple computer for more than 20 years, since the first little Apple IIc that I had. This is the first thing that I haven't been able to figure out.
Thank you,
Linda

HI,
This
1. It says insufficient bandwidth"
2. It says "starting" for a LONG time, and never finishes.
3. Or they request a chat with me and I get a "Did not respond" message.
Normally implies the ports are not open some where.
The bit I have changed to Bold is not specific enough
I have tried connecting with both my .mac account and my aim name inside of iChat
So far, I have:
1. Changed Quicktime streaming to 1mbps Cable
2. Reinstalled Quicktime 7.0.1, erasing 7.0.3
3. Made an ichat AV entry under Firewall, listing TCP etc ports for network entry, using numbers from previous posts
4. Firewall is off
Can you tell us exactly which ports you have opened and which protocols. APple Doc 93208 is Wrong.
1. All iChat AV traffic is UDP except for ports 5190 and 5298, which need to be open for both TCP and UDP; and 5220, 5222, and 16384-16403, which need to be open for TCP only.
You have not siad what ports you have opened and by what method in your modem ?
Ralph

Firefox hangs with a "Script not responding" error message; in the meantime there are more and more flashplayer instances running

Recently I receive errors from Firefox at sites that were working fine before, always the same: a script is not responding, and I can wait, debug or stop. Waiting doesn't help (therefore pointless to change the 'dom.max_script_run_time' setting in the config); and also pointless to debug because the problem is not with the script. "Stop" eventually gets firefox to work, until the next error message which comes very soon.
I tried to reinstall both Firefox and Flashplayer, even manually wiped the traces from the user profile and program files. They are the latest 35.0.1 and 16.0.0.305 available now.
=> In the meantime, there are reproducing instances of flash players are spawned and running. They stay running even after firefox is closed or terminated.
=> if I disable the flash player plugin everything's fine except of course flash is not working. If I re-enable it, the problem starts over.
OS is Windows 8.1

Retard, (I know that sounds hilarious, but I don't know your name - no offense please! )
Like you said, if this happens only primarily on one of the many sites, it generally comes down to the type of code on that site.
And after looking at the URL you posted, seems like that page uses a lot of external references - JS and CSS.
Especially the last few lines:
<script type="text/javascript" src="http://njcdn.worldsecuresystems.com/CatalystScripts/Java_OnlineShopping.js?vs=b1763.r38875 7"></script>
<script type="text/javascript" src="http://njcdn.worldsecuresystems.com/CatalystScripts/Java_Cookies.js?vs=b1763.r388757"></script>
<script type="text/javascript" src="http://njcdn.worldsecuresystems.com/CatalystScripts/Java_Box.js?vs=b1763.r388757"></script>
Also, a couple CSS, JS references in the <head> section.
'Display External Files' only disables showing external files - but still loads them.
Can you try removing the external references and try working with the webpage in DW for a few minutes to see if the same problem persists? If it does, we know what was causing your issue.
Also, run your site through W3 validator to check and resolve errors: http://validator.w3.org/check?uri=http%3A%2F%2Fwww.healthfirst.com%2Facls-kit.html&charset =%28detect+automatically%29&doctype=Inline&group=0
Let us know how it goes.
Good luck.
-ST

On my iPad, wifi connected but receive "server not responding" error messages on every app including iTunes. Rebooted, reset settings (all

Help! Was using my iPad yesterday set it down for 10 minutes and all of a sudden received "server not responding" and "Cannot verify server" error messages. Cannot open/connect to iTunes to update software. Wifi is working with strong signal. Followed other message board suggestions: forgot network and readded, renewed lease, turned wifi off/on, reset network settings, reset all settings, powered off/on, rebooted, checked router. Internet works fine on laptop. I'm so frustrated and don't know what else to do. Any suggestions?

Hello there, Swass26.
The following Knowledge Base article provides some great in-depth troubleshooting steps to get to the bottom of your issue:
Can't connect to the iTunes Store
http://support.apple.com/kb/TS1368
Thanks for reaching out to Apple Support Communities.
Cheers,
Pedro D.

ITunes not responding error message when iPod is connected

I cleaned up all of my music on my external hardrive. I moved the cleaned up librery to iTunes. I connected my 30G iPod and I reset the content on the iPod, but now I can not sync with the computer and Itunes frezes and gives me an error saying that Itunes is not responding. This happens everytime I connect my iPod; now I have no music on the Pod.

hi joyful!
just checking. reboot the PC, and prior to launching itunes or plugging in the ipod, bring up your Task Manager to the "processes" tab.
is there an iTunesHelper.exe running in your processes?
Background processes installed with iTunes 6 for Windows
love, b

"Did not respond" error message

hey all,
i'm sure you're all sick and tired of hearing this question, but i have to ask. here's the story, my mom recently got an iMac G5. i'm a college student in CA, and while i was home with my mom in CO, i used my mom's iMac G5 with built in iSight to video conference with girlfriend in MN. SO, i know that both my mom's iSight and my girlfriend's camera (although she does have a PC) work without a problem!
now that i'm back at school, i thought it'd be nice to have iSight for my iBook G4 to video conference with my mom and my girlfriend. however, having plugged in my brand new iSight and tested it (it does show me on the screen), when i try to v-conference with my mom or my girlfriend, it says THEY did not respond. despite this message, i'm thinking the problem is me since i know for a fact that both of theirs work. given that i'm on a college campus and there's a lot of talk about Firewall restrictions on college networks i'm wondering if that could be the problem. i tried connecting with the Apple "test" screennames, and it said that "appleu3test02" did not respond.
my Connection Doctor says:
2006-01-26 18:03:18 -0800: MBergner did not respond.
Tried to send UDP SIP "invite" to the following IP addresses and ports:
24.221.209.14:10616, 192.168.0.119:5060
2006-01-26 18:22:26 -0800: Apple Test did not respond.
Tried to send UDP SIP "invite" to the following IP addresses and ports:
17.202.39.240:5060
2006-01-26 18:25:40 -0800: appleu3test01 did not respond.
Tried to send UDP SIP "invite" to the following IP addresses and ports:
17.202.39.240:5060
Anyone have any suggestions? MUCH appreciated. i just spent $150 on iSight and it would be a shame to not be able to use it for the ONE reason i bought it. thanks so much!!
David

Hi David,
Who is your Mom's ISP ?
Do you mean that when the connection goes out of her house it is Wireless to some pint down the street ?
Or is she piggybacking on to someone else's service ?
I take it you sister is on a Wireless ISP service ?
OK. Your college for instance will be using a connection to the internet. In a home situation that interface is usually done by a modem whether or not it is to a Cable, Wirelss or DSL service.
In that modem the ports have to be open for iChat.
The same is true of teh device the colege uses to connect to the interent.
Some people also elect to have a router in their room so that they can use things like games consols over the same connection as their computer uses.
That router would also need the ports open for iChat.
There are differing methods for opening the ports.
Port Forwarding can take the data on one port from the internet (Outside) and point it to one computer on your local net. Most often the ports are kept the Same.
Port Triggering is similar but allows several coputers to use the same ports and waits until data comes on a specific port before others are open.
UPnP give control of the ports to the Application and opens them when the application needs them.
Do you plug straight into a wall socket ?
If so you may need to talk to the IT guys about which ports they have open.
The Apple Doc does say you only need the ports you list but the modem or connection device will,need more.
5060, 5190, 5678, 16384-16403 for the AIM AV contacts
5297, 5298 and 5353 are for Bonjour/Rendezvous
Apple Doc 93208 is also wrong at Note 1.
It should read:
1. All iChat AV traffic is UDP except for ports 5190 and 5298, which need to be open for both TCP and UDP; and 5220, 5222, and 5223 which need to be open for TCP only.
This Doc is now for iChat 3 as well and the TCP ports at the end are the Jabber ones thatare added for iChat 3 You need the Bold and italised text.
The UDP and TCP protocols listed are used more often in Port Triggering and are needed in the Tiger version of the MAc firewall that you seem to have set ports in.
The college of course may be blocking the ports for iChat so that their server is not over burdened by Video chats.
Can you Log in to AIM ?
Ralph

Apple TV not responding error message

Hi, we bought our ATV probably 6-8 months ago and its been great - not one issue.
We bought ATV Flash recently, installed it and noticed that we got the "Apple TV myATV is not responding, blah blah make sure firewalls allow port 3689" message.
I don't think its related, because I've formatted the ATV, re-installed 3.02 and all the content on the ATV (as expected) is gone.
However, I had this problem after it as well, so I fiddled and rebooted our reasonably new AEBS (the latest model), and also the ATV and it started working.
However syncing was incredibly slow, it took about an hour and a half to sync a one hour movie (1.8GB). Even a week ago it wasn't like this!
We have a modem that is connected to our AEBS via an ethernet cable.
I had successfully been able to sync one 1.8GB movie to the ATV which I was watching, I was trying to sync another two, I thought they were working because at one point it was at 50%, but when I came out later it was back at 5% and not moving.
I wasn't getting any internet for any of our computers, so I tried rebooting it and that wouldn't work (via airport) so I pulled the power cord out and plugged it back in. The indicator went orange and wouldn't change, so I tried pulling it out and plugging it back in, eventually it went green.
Internet was back, and I sync'd two episodes to the ATV, it was going faster but still was way too slow.
So I thought the issue was solved, and went into the movies tab and selected about ~20 movies to sync to the ATV, and then it gave me the message.
I'm not sure what the problem is can anyone help?

That's what I meant when I said I formatted the ATV, I restored it to factory settings. The issue still persists after that, that's how I figure it's not the ATV Flash.
I either get a "Not responding" message, or it just goes ridiculously slow.
At the moment, I'm syncing 36 movies over and it fits in that latter category, I'll have to wait and see if makes any progress or is just stuck.
According to activity monitor, 500KB/s is being sent over the network.
I've noticed a big slow down with the internet while this is going on though, took me like 10 seconds to open Apple.com/support, and it's bad enough that a game I want to play shows that I'm not connected to the internet!
//Actually I think the game is just getting maintenace
Only a short while ago we moved the AEBS to a better location - it was behind a 30" ACD, so it's been moved and has improved the WiFi signal strength down the end of the house (which isn't too far).
But even when it was behind the 30" the ATV never had any issue before.

Using foxfire I get a lot of not responding error messages

Whenever you are surfing the net foxfire unexpectedly freezes on you. You get a not responding message.

Yes, I know about that article. I know how to handle the untrusted connection in normal circumstances. I know it has something to do with being behind a proxy. (I have no problems hitting the same sites from my home PC.) My question is how to handle it when the "I understand the risks" option isn't presented and I thus can't add an exception and continue on to the site.

Remote gateway is not responding error message

Similar Messages

Maybe you are looking for