Remote Office - Remote Control - Remote Access ??
What you describe doesn't really make me suspect hacking. What model router? Many routers need to have their config saved into NVRAM or else it is lost after a power cycle. If it is some SMB, consumer grade router it may just be junk and do that. One other option may be that someone on site decided to put a paperclip in the reset hole to see if they could fix the Internet..
I'm sure there is a solution, just haven't come across it yet...
We have remote offices, with remote access, etc.
With one critical exception......LOSS of Internet Connection.
No one at the remote offices even have a clue as to what a router is....
We are looking for a solution to place something (PC, Laptop, Raspberry Pi) that is on the LAN that is then accessible from the Wireless Communications Network 4G that would allow us access to the router, to reset the configuration or restore the configuration etc.
It goes without saying it needs to be secure, available 24x7.
Any ideas? This question was posed by our CEO, since it can take up to 3 hrs to be onsite with some of our locations.
This topic first appeared in the Spiceworks Community
Similar Messages
-
Will I be able to completely remotely control and access my Office Mac from my Macbook Air at home?
I am in a bit of a dilemma and need some help from the community. I have a Mac Mini running 16GB Ram 2.3 I7 and 1 TB Fusion Drive at my office, it is in Parrallels Coherence mode 100% of the time. I have to run certain Windows apps from home. I am setting my routers at the office to accept NAT-PMP, or Plug and Play so that I can access them.
I have two questions:
1. Will I be able to use back to my mac, or screen share to completely operate and share my mac mini with a new mac book air?
2. I am buying a new MacBook Air, I am under the assumption that I can get the 13" 4gb, I5, with 256 GB and I should be able to quickly access and handle all basic remote access, iphoto stuff and some i movie stuff occassionally.
Am I correct in these assumptions? Any recommendations?
I do have IPAD apps that can also access two of the three windows apps that are critical to my company, but really need a traditional computer with mouse to run them effectively remotely.
Thanks in advance for your help,
John1. Will I be able to use back to my mac, or screen share to completely operate and share my mac mini with a new mac book air?
2. I am buying a new MacBook Air, I am under the assumption that I can get the 13" 4gb, I5, with 256 GB and I should be able to quickly access and handle all basic remote access, iphoto stuff and some i movie stuff occassionally.
Yes to both, as long as the Mini is running Mountain Lion or later OS you can use Back to My Mac and Screen Sharing. It will be as though you are seated at the remote Mac. Connections and speed will be determined by Internet conditions.
OS X Mountain Lion: Share your screen using Back to My Mac
It's pretty seamless. Copying files for example is a simple matter of dragging them to or from the Screen Sharing window. If you have multiple users on the Mini you can log in remotely as any user for which you have access, or share the screen interactively with a user's consent.
The only uncertainties are your router, but according to Apple all that should be required is to enable NAT-PMP or UPnP.
I use Apple routers, to eliminate any uncertainty. -
Remote access my office mac from my home mac
I know this is not the right forum for this, but I am not sure which one is and so I am asking this question here in the hopes that someone will direct me to the right place.
If I want to access my office mac from home, what program do I need to use? (Apple Remote Desktop?) Where can I find detailed instructions?
Other pertinent details:
I have a PB at home and one at the office, both running OSX.3.
Both are on a wireless network.
Office is behind a firewall.
Because both computers are on a wireless network, their IP addresses are of the form 10.0.1.xxx. Turning on File sharing on the office computer and then doing "ssh [email protected].....etc. does not seem to work.
Ideally I want to be able to remotely run programs on the office computer. I know this ability exists for Windows XP (and my colleagues use it), so it MUST exist for Macs.
Any help will be much appreciated.
Thanks,
NSns,
Apple Remote Desktop and Timbuktu Pro are worthy programs; you can achieve the same effects with free VNC (virtual network connection) software. Essentially, you set one Mac up as a VNC server, the other as a VNC client, and connect the client to the server. Check Version Tracker and/or MacUpdate for such freeware as VNCThing (OS 9 client), OSXvnc (OS X server), and Chicken of the VNC (OS X client).
The firewall will require you to set up port forwarding. I've actually found the FAQ and help info at the site for the Windows program UltraVNC along with PortForward more than enough to figure how to set up a VNC link to a Windows PC in my wife's office that could be accessed by either my office Mac (before turning on the link encryption) or her home PC. Adding / using SSH is somewhat more complicated and outside of my firsthand experience, but there are references at e.g. SSH VNC Tunneling (try Googling "SSH VNC Mac"). See for example:
Homemade Dot-Mac: Remote Control
MacMod - Your Mac Modding HQ
VNC Sessions From Off-Campus
Note that if you have the usual dynamic IP account at home and a static IP at work, it will be easier to set up the work computer as the server since the IP number will be a fixed address. If both computers are on dynamic IP accounts, the server's IP number will have to be checked locally before connecting remotely (one reason ISPs can charge extra for static IP accounts). -
Remote access database using EM Database Control Console
When I install the Oracle database 10g, it gives me two choices:
1)Using Grid Control for Database Management and
2)Using Database Control for Database Management.
When I select the #2, according to the Guide, I'll be able to manage my database locally. (Assume the database server's IP address is: DB_IP_Address, then I can use: http://DB_IP_Address:5560/em). But wait a minute___
a)What does this "locally" mean? If the Oracle DB is installed in a remote location, and there is no LAN connection to it, can I still access it via the Oracle Enterprise Manager (Database Control Console)? (i.e., via the HTTP protocol)
b)The same question is asked for the iSQL*Plus in regarding to the remote access. I guess the answer to a) above will automatically answer the b) ? (Actually I doubt that I can access remote database using the iSQL*Plus via HTTP protocol).
Thanks
ScottHi,
and there is no LAN connection to itWell you'll need some network link in order to connect successfully.
What is meant by locally is that you can only manage databases installed on the local computer.
For example if you installed it on machine "CPTR1", and on another machine "CPTR2", then you can't use http://cptr1:5560/em to manage the databases on "CPTR2. And vice versa.
About iSQL*Plus, in fact, as far as the tns alias is ok from "CPTR1", you can connect to the databases on "CPTR2", "CPTR3", ....
HTH,
Yoann. -
Remote Access VPN Problem with ASA 5505
After about ~1 year of having the Cisco VPN Client connecting to a ASA 5505 without any problems, suddenly one day it stops working. The client is able to get a connection to the ASA and browse the local network for only about 30 seconds after connection. After that, no access is available to the network behind the ASA. I tried everything that I can think of to try and troubleshoot the problem, but at this point I am just banging my head against a wall. Does anyone know what could cause this?
Here is the running cfg of the ASA
: Saved
ASA Version 8.4(1)
hostname NCHCO
enable password xxxxxxxxxxxxxxx encrypted
passwd xxxxxxxxxxx encrypted
names
name 192.168.2.0 NCHCO description City Offices
name 192.168.2.80 VPN_End
name 192.168.2.70 VPN_Start
interface Vlan1
nameif inside
security-level 100
ip address 192.168.2.1 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address **.**.***.*** 255.255.255.248
interface Ethernet0/0
switchport access vlan 2
speed 100
duplex full
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
boot system disk0:/asa841-k8.bin
ftp mode passive
object network NCHCO
subnet 192.168.2.0 255.255.255.0
object network obj-192.168.1.0
subnet 192.168.1.0 255.255.255.0
object network obj-192.168.2.64
subnet 192.168.2.64 255.255.255.224
object network obj-0.0.0.0
subnet 0.0.0.0 255.255.255.0
object network obj_any
subnet 0.0.0.0 0.0.0.0
object network Webserver
object network FINX
host 192.168.2.11
object service rdp
service tcp source range 1 65535 destination eq 3389
description rdp
access-list outside_nat0_outbound extended permit ip object NCHCO 192.168.1.0 255.255.255.0
access-list outside_nat0_outbound extended permit ip object NCHCO 192.168.2.0 255.255.255.0
access-list inside_nat0_outbound extended permit ip object NCHCO 192.168.1.0 255.255.255.0
access-list inside_nat0_outbound extended permit ip any 192.168.2.64 255.255.255.224
access-list inside_nat0_outbound extended permit ip 0.0.0.0 255.255.255.0 192.168.2.64 255.255.255.224
access-list outside_1_cryptomap extended permit ip object NCHCO 192.168.1.0 255.255.255.0
access-list outside_1_cryptomap_1 extended permit ip object NCHCO 192.168.1.0 255.255.255.0
access-list LAN_Access standard permit 192.168.2.0 255.255.255.0
access-list LAN_Access standard permit 0.0.0.0 255.255.255.0
access-list NCHCO_splitTunnelAcl_1 standard permit 192.168.2.0 255.255.255.0
access-list AnyConnect_Client_Local_Print extended deny ip any any
access-list AnyConnect_Client_Local_Print extended permit tcp any any eq lpd
access-list AnyConnect_Client_Local_Print remark IPP: Internet Printing Protocol
access-list AnyConnect_Client_Local_Print extended permit tcp any any eq 631
access-list AnyConnect_Client_Local_Print remark Windows' printing port
access-list AnyConnect_Client_Local_Print extended permit tcp any any eq 9100
access-list AnyConnect_Client_Local_Print remark mDNS: multicast DNS protocol
access-list AnyConnect_Client_Local_Print extended permit udp any host 224.0.0.251 eq 5353
access-list AnyConnect_Client_Local_Print remark LLMNR: Link Local Multicast Name Resolution protocol
access-list AnyConnect_Client_Local_Print extended permit udp any host 224.0.0.252 eq 5355
access-list AnyConnect_Client_Local_Print remark TCP/NetBIOS protocol
access-list AnyConnect_Client_Local_Print extended permit tcp any any eq 137
access-list AnyConnect_Client_Local_Print extended permit udp any any eq netbios-ns
access-list outside_access_in extended permit tcp any object FINX eq 3389
access-list outside_access_in_1 extended permit object rdp any object FINX
pager lines 24
logging enable
logging asdm informational
mtu inside 1500
mtu outside 1500
ip local pool VPN_Pool VPN_Start-VPN_End mask 255.255.255.0
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-649.bin
no asdm history enable
arp timeout 14400
nat (inside,any) source static NCHCO NCHCO destination static obj-192.168.1.0 obj-192.168.1.0
nat (inside,any) source static any any destination static obj-192.168.2.64 obj-192.168.2.64
nat (inside,any) source static obj-0.0.0.0 obj-0.0.0.0 destination static obj-192.168.2.64 obj-192.168.2.64
object network obj_any
nat (inside,outside) dynamic interface
object network FINX
nat (inside,outside) static interface service tcp 3389 3389
access-group outside_access_in_1 in interface outside
route outside 0.0.0.0 0.0.0.0 69.61.228.177 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-record DfltAccessPolicy
network-acl outside_nat0_outbound
webvpn
svc ask enable default svc
http server enable
http 192.168.1.0 255.255.255.0 inside
http **.**.***.*** 255.255.255.255 outside
http **.**.***.*** 255.255.255.255 outside
http NCHCO 255.255.255.0 inside
http 96.11.251.186 255.255.255.255 outside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
crypto ipsec ikev1 transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec ikev1 transform-set l2tp-transform esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set l2tp-transform mode transport
crypto ipsec ikev1 transform-set vpn-transform esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set TRANS_ESP_3DES_SHA esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set TRANS_ESP_3DES_SHA mode transport
crypto ipsec ikev1 transform-set TRANS_ESP_3DES_MD5 esp-3des esp-md5-hmac
crypto ipsec ikev1 transform-set TRANS_ESP_3DES_MD5 mode transport
crypto ipsec ikev1 transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs group1
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto dynamic-map dyn-map 10 set pfs group1
crypto dynamic-map dyn-map 10 set ikev1 transform-set l2tp-transform vpn-transform
crypto dynamic-map dyn-map 10 set reverse-route
crypto dynamic-map outside_dyn_map 20 set ikev1 transform-set ESP-3DES-SHA
crypto dynamic-map outside_dyn_map 20 set reverse-route
crypto map outside_map 1 match address outside_1_cryptomap
crypto map outside_map 1 set pfs group1
crypto map outside_map 1 set peer 74.219.208.50
crypto map outside_map 1 set ikev1 transform-set ESP-3DES-SHA
crypto map outside_map 20 ipsec-isakmp dynamic outside_dyn_map
crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map outside_map interface outside
crypto map inside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map inside_map interface inside
crypto map vpn-map 1 match address outside_1_cryptomap_1
crypto map vpn-map 1 set pfs group1
crypto map vpn-map 1 set peer 74.219.208.50
crypto map vpn-map 1 set ikev1 transform-set ESP-3DES-SHA
crypto map vpn-map 10 ipsec-isakmp dynamic dyn-map
crypto isakmp identity address
crypto ikev1 enable inside
crypto ikev1 enable outside
crypto ikev1 ipsec-over-tcp port 10000
crypto ikev1 policy 10
authentication pre-share
encryption 3des
hash md5
group 2
lifetime 86400
crypto ikev1 policy 15
authentication pre-share
encryption aes-256
hash sha
group 2
lifetime 86400
crypto ikev1 policy 35
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
client-update enable
telnet 192.168.1.0 255.255.255.0 inside
telnet NCHCO 255.255.255.0 inside
telnet timeout 5
ssh 192.168.1.0 255.255.255.0 inside
ssh NCHCO 255.255.255.0 inside
ssh timeout 5
console timeout 0
dhcpd address 192.168.2.150-192.168.2.225 inside
dhcpd dns 216.68.4.10 216.68.5.10 interface inside
dhcpd lease 64000 interface inside
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
group-policy DefaultRAGroup internal
group-policy DefaultRAGroup attributes
dns-server value 192.168.2.1
vpn-tunnel-protocol ikev1 l2tp-ipsec
default-domain value nchco.local
group-policy DfltGrpPolicy attributes
dns-server value 192.168.2.1
vpn-tunnel-protocol ikev1 l2tp-ipsec ssl-client ssl-clientless
password-storage enable
ipsec-udp enable
intercept-dhcp 255.255.255.0 enable
address-pools value VPN_Pool
group-policy NCHCO internal
group-policy NCHCO attributes
dns-server value 192.168.2.1 8.8.8.8
vpn-tunnel-protocol ikev1
split-tunnel-policy tunnelspecified
split-tunnel-network-list value NCHCO_splitTunnelAcl_1
default-domain value NCHCO.local
username admin password LbMiJuAJjDaFb2uw encrypted privilege 15
username 8njferg password yB1lHEVmHZGj5C2Z encrypted privilege 15
username NCHvpn99 password dhn.JzttvRmMbHsP encrypted
tunnel-group DefaultRAGroup general-attributes
address-pool (inside) VPN_Pool
address-pool VPN_Pool
authentication-server-group (inside) LOCAL
authentication-server-group (outside) LOCAL
authorization-server-group LOCAL
authorization-server-group (inside) LOCAL
authorization-server-group (outside) LOCAL
default-group-policy DefaultRAGroup
strip-realm
strip-group
tunnel-group DefaultRAGroup ipsec-attributes
ikev1 pre-shared-key *****
peer-id-validate nocheck
tunnel-group DefaultRAGroup ppp-attributes
no authentication chap
no authentication ms-chap-v1
authentication ms-chap-v2
tunnel-group DefaultWEBVPNGroup ppp-attributes
authentication pap
authentication ms-chap-v2
tunnel-group 74.219.208.50 type ipsec-l2l
tunnel-group 74.219.208.50 ipsec-attributes
ikev1 pre-shared-key *****
tunnel-group NCHCO type remote-access
tunnel-group NCHCO general-attributes
address-pool VPN_Pool
default-group-policy NCHCO
tunnel-group NCHCO ipsec-attributes
ikev1 pre-shared-key *****
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
service-policy global_policy global
prompt hostname context
call-home
profile CiscoTAC-1
no active
destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService
destination address email [email protected]
destination transport-method http
subscribe-to-alert-group diagnostic
subscribe-to-alert-group environment
subscribe-to-alert-group inventory periodic monthly
subscribe-to-alert-group configuration periodic monthly
subscribe-to-alert-group telemetry periodic daily
Cryptochecksum:a2110206e1af06974c858fb40c6de2fc
: end
asdm image disk0:/asdm-649.bin
asdm location VPN_Start 255.255.255.255 inside
asdm location VPN_End 255.255.255.255 inside
no asdm history enable
And here is the logs from the Cisco VPN Client when it browses, then fails to browse the network behind the ASA:
Cisco Systems VPN Client Version 5.0.07.0440
Copyright (C) 1998-2010 Cisco Systems, Inc. All Rights Reserved.
Client Type(s): Windows, WinNT
Running on: 6.1.7601 Service Pack 1
Config file directory: C:\Program Files (x86)\Cisco Systems\VPN Client\
1 09:44:55.677 10/01/13 Sev=Info/6 CERT/0x63600026
Attempting to find a Certificate using Serial Hash.
2 09:44:55.677 10/01/13 Sev=Info/6 CERT/0x63600027
Found a Certificate using Serial Hash.
3 09:44:55.693 10/01/13 Sev=Info/6 GUI/0x63B00011
Reloaded the Certificates in all Certificate Stores successfully.
4 09:45:02.802 10/01/13 Sev=Info/4 CM/0x63100002
Begin connection process
5 09:45:02.802 10/01/13 Sev=Info/4 CM/0x63100004
Establish secure connection
6 09:45:02.802 10/01/13 Sev=Info/4 CM/0x63100024
Attempt connection with server "**.**.***.***"
7 09:45:02.802 10/01/13 Sev=Info/6 IKE/0x6300003B
Attempting to establish a connection with **.**.***.***.
8 09:45:02.818 10/01/13 Sev=Info/4 IKE/0x63000001
Starting IKE Phase 1 Negotiation
9 09:45:02.865 10/01/13 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK AG (SA, KE, NON, ID, VID(Xauth), VID(dpd), VID(Frag), VID(Nat-T), VID(Unity)) to **.**.***.***
10 09:45:02.896 10/01/13 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = **.**.***.***
11 09:45:02.896 10/01/13 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK AG (SA, KE, NON, ID, HASH, VID(Unity), VID(Xauth), VID(dpd), VID(Nat-T), NAT-D, NAT-D, VID(Frag), VID(?)) from **.**.***.***
12 09:45:02.896 10/01/13 Sev=Info/5 IKE/0x63000001
Peer is a Cisco-Unity compliant peer
13 09:45:02.896 10/01/13 Sev=Info/5 IKE/0x63000001
Peer supports XAUTH
14 09:45:02.896 10/01/13 Sev=Info/5 IKE/0x63000001
Peer supports DPD
15 09:45:02.896 10/01/13 Sev=Info/5 IKE/0x63000001
Peer supports NAT-T
16 09:45:02.896 10/01/13 Sev=Info/5 IKE/0x63000001
Peer supports IKE fragmentation payloads
17 09:45:02.927 10/01/13 Sev=Info/6 IKE/0x63000001
IOS Vendor ID Contruction successful
18 09:45:02.927 10/01/13 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK AG *(HASH, NOTIFY:STATUS_INITIAL_CONTACT, NAT-D, NAT-D, VID(?), VID(Unity)) to **.**.***.***
19 09:45:02.927 10/01/13 Sev=Info/4 IKE/0x63000083
IKE Port in use - Local Port = 0xDD3B, Remote Port = 0x01F4
20 09:45:02.927 10/01/13 Sev=Info/5 IKE/0x63000072
Automatic NAT Detection Status:
Remote end is NOT behind a NAT device
This end is NOT behind a NAT device
21 09:45:02.927 10/01/13 Sev=Info/4 CM/0x6310000E
Established Phase 1 SA. 1 Crypto Active IKE SA, 0 User Authenticated IKE SA in the system
22 09:45:02.943 10/01/13 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = **.**.***.***
23 09:45:02.943 10/01/13 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK TRANS *(HASH, ATTR) from **.**.***.***
24 09:45:02.943 10/01/13 Sev=Info/4 CM/0x63100015
Launch xAuth application
25 09:45:03.037 10/01/13 Sev=Info/6 GUI/0x63B00012
Authentication request attributes is 6h.
26 09:45:03.037 10/01/13 Sev=Info/4 CM/0x63100017
xAuth application returned
27 09:45:03.037 10/01/13 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK TRANS *(HASH, ATTR) to **.**.***.***
28 09:45:03.037 10/01/13 Sev=Info/4 IPSEC/0x63700008
IPSec driver successfully started
29 09:45:03.037 10/01/13 Sev=Info/4 IPSEC/0x63700014
Deleted all keys
30 09:45:03.083 10/01/13 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = **.**.***.***
31 09:45:03.083 10/01/13 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK TRANS *(HASH, ATTR) from **.**.***.***
32 09:45:03.083 10/01/13 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK TRANS *(HASH, ATTR) to **.**.***.***
33 09:45:03.083 10/01/13 Sev=Info/4 CM/0x6310000E
Established Phase 1 SA. 1 Crypto Active IKE SA, 1 User Authenticated IKE SA in the system
34 09:45:03.083 10/01/13 Sev=Info/5 IKE/0x6300005E
Client sending a firewall request to concentrator
35 09:45:03.083 10/01/13 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK TRANS *(HASH, ATTR) to **.**.***.***
36 09:45:03.146 10/01/13 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = **.**.***.***
37 09:45:03.146 10/01/13 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK TRANS *(HASH, ATTR) from **.**.***.***
38 09:45:03.146 10/01/13 Sev=Info/5 IKE/0x63000010
MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_ADDRESS: , value = 192.168.2.70
39 09:45:03.146 10/01/13 Sev=Info/5 IKE/0x63000010
MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_NETMASK: , value = 255.255.255.0
40 09:45:03.146 10/01/13 Sev=Info/5 IKE/0x63000010
MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_DNS(1): , value = 192.168.2.1
41 09:45:03.146 10/01/13 Sev=Info/5 IKE/0x63000010
MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_DNS(2): , value = 8.8.8.8
42 09:45:03.146 10/01/13 Sev=Info/5 IKE/0x6300000D
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_SAVEPWD: , value = 0x00000001
43 09:45:03.146 10/01/13 Sev=Info/5 IKE/0x6300000D
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_SPLIT_INCLUDE (# of split_nets), value = 0x00000001
44 09:45:03.146 10/01/13 Sev=Info/5 IKE/0x6300000F
SPLIT_NET #1
subnet = 192.168.2.0
mask = 255.255.255.0
protocol = 0
src port = 0
dest port=0
45 09:45:03.146 10/01/13 Sev=Info/5 IKE/0x6300000E
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_DEFDOMAIN: , value = NCHCO.local
46 09:45:03.146 10/01/13 Sev=Info/5 IKE/0x6300000D
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_UDP_NAT_PORT, value = 0x00002710
47 09:45:03.146 10/01/13 Sev=Info/5 IKE/0x6300000D
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_PFS: , value = 0x00000000
48 09:45:03.146 10/01/13 Sev=Info/5 IKE/0x6300000E
MODE_CFG_REPLY: Attribute = APPLICATION_VERSION, value = Cisco Systems, Inc ASA5505 Version 8.4(1) built by builders on Mon 31-Jan-11 02:11
49 09:45:03.146 10/01/13 Sev=Info/5 IKE/0x6300000D
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_SMARTCARD_REMOVAL_DISCONNECT: , value = 0x00000001
50 09:45:03.146 10/01/13 Sev=Info/4 CM/0x63100019
Mode Config data received
51 09:45:03.146 10/01/13 Sev=Info/4 IKE/0x63000056
Received a key request from Driver: Local IP = 192.168.2.70, GW IP = **.**.***.***, Remote IP = 0.0.0.0
52 09:45:03.146 10/01/13 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK QM *(HASH, SA, NON, ID, ID) to **.**.***.***
53 09:45:03.177 10/01/13 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = **.**.***.***
54 09:45:03.177 10/01/13 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK INFO *(HASH, NOTIFY:STATUS_RESP_LIFETIME) from **.**.***.***
55 09:45:03.177 10/01/13 Sev=Info/5 IKE/0x63000045
RESPONDER-LIFETIME notify has value of 86400 seconds
56 09:45:03.177 10/01/13 Sev=Info/5 IKE/0x63000047
This SA has already been alive for 1 seconds, setting expiry to 86399 seconds from now
57 09:45:03.193 10/01/13 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = **.**.***.***
58 09:45:03.193 10/01/13 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK QM *(HASH, SA, NON, ID, ID, NOTIFY:STATUS_RESP_LIFETIME) from **.**.***.***
59 09:45:03.193 10/01/13 Sev=Info/5 IKE/0x63000045
RESPONDER-LIFETIME notify has value of 28800 seconds
60 09:45:03.193 10/01/13 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK QM *(HASH) to **.**.***.***
61 09:45:03.193 10/01/13 Sev=Info/5 IKE/0x63000059
Loading IPsec SA (MsgID=967A3C93 OUTBOUND SPI = 0xAAAF4C1C INBOUND SPI = 0x3EBEBFC5)
62 09:45:03.193 10/01/13 Sev=Info/5 IKE/0x63000025
Loaded OUTBOUND ESP SPI: 0xAAAF4C1C
63 09:45:03.193 10/01/13 Sev=Info/5 IKE/0x63000026
Loaded INBOUND ESP SPI: 0x3EBEBFC5
64 09:45:03.193 10/01/13 Sev=Info/5 CVPND/0x63400013
Destination Netmask Gateway Interface Metric
0.0.0.0 0.0.0.0 96.11.251.1 96.11.251.149 261
96.11.251.0 255.255.255.0 96.11.251.149 96.11.251.149 261
96.11.251.149 255.255.255.255 96.11.251.149 96.11.251.149 261
96.11.251.255 255.255.255.255 96.11.251.149 96.11.251.149 261
127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 306
127.0.0.1 255.255.255.255 127.0.0.1 127.0.0.1 306
127.255.255.255 255.255.255.255 127.0.0.1 127.0.0.1 306
192.168.1.0 255.255.255.0 192.168.1.3 192.168.1.3 261
192.168.1.3 255.255.255.255 192.168.1.3 192.168.1.3 261
192.168.1.255 255.255.255.255 192.168.1.3 192.168.1.3 261
224.0.0.0 240.0.0.0 127.0.0.1 127.0.0.1 306
224.0.0.0 240.0.0.0 96.11.251.149 96.11.251.149 261
224.0.0.0 240.0.0.0 192.168.1.3 192.168.1.3 261
255.255.255.255 255.255.255.255 127.0.0.1 127.0.0.1 306
255.255.255.255 255.255.255.255 96.11.251.149 96.11.251.149 261
255.255.255.255 255.255.255.255 192.168.1.3 192.168.1.3 261
65 09:45:03.521 10/01/13 Sev=Info/6 CVPND/0x63400001
Launch VAInst64 to control IPSec Virtual Adapter
66 09:45:03.896 10/01/13 Sev=Info/4 CM/0x63100034
The Virtual Adapter was enabled:
IP=192.168.2.70/255.255.255.0
DNS=192.168.2.1,8.8.8.8
WINS=0.0.0.0,0.0.0.0
Domain=NCHCO.local
Split DNS Names=
67 09:45:03.912 10/01/13 Sev=Info/5 CVPND/0x63400013
Destination Netmask Gateway Interface Metric
0.0.0.0 0.0.0.0 96.11.251.1 96.11.251.149 261
96.11.251.0 255.255.255.0 96.11.251.149 96.11.251.149 261
96.11.251.149 255.255.255.255 96.11.251.149 96.11.251.149 261
96.11.251.255 255.255.255.255 96.11.251.149 96.11.251.149 261
127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 306
127.0.0.1 255.255.255.255 127.0.0.1 127.0.0.1 306
127.255.255.255 255.255.255.255 127.0.0.1 127.0.0.1 306
192.168.1.0 255.255.255.0 192.168.1.3 192.168.1.3 261
192.168.1.3 255.255.255.255 192.168.1.3 192.168.1.3 261
192.168.1.255 255.255.255.255 192.168.1.3 192.168.1.3 261
224.0.0.0 240.0.0.0 127.0.0.1 127.0.0.1 306
224.0.0.0 240.0.0.0 96.11.251.149 96.11.251.149 261
224.0.0.0 240.0.0.0 192.168.1.3 192.168.1.3 261
224.0.0.0 240.0.0.0 0.0.0.0 0.0.0.0 261
255.255.255.255 255.255.255.255 127.0.0.1 127.0.0.1 306
255.255.255.255 255.255.255.255 96.11.251.149 96.11.251.149 261
255.255.255.255 255.255.255.255 192.168.1.3 192.168.1.3 261
255.255.255.255 255.255.255.255 0.0.0.0 0.0.0.0 261
68 09:45:07.912 10/01/13 Sev=Info/4 CM/0x63100038
Successfully saved route changes to file.
69 09:45:07.912 10/01/13 Sev=Info/5 CVPND/0x63400013
Destination Netmask Gateway Interface Metric
0.0.0.0 0.0.0.0 96.11.251.1 96.11.251.149 261
**.**.***.*** 255.255.255.255 96.11.251.1 96.11.251.149 100
96.11.251.0 255.255.255.0 96.11.251.149 96.11.251.149 261
96.11.251.149 255.255.255.255 96.11.251.149 96.11.251.149 261
96.11.251.255 255.255.255.255 96.11.251.149 96.11.251.149 261
127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 306
127.0.0.1 255.255.255.255 127.0.0.1 127.0.0.1 306
127.255.255.255 255.255.255.255 127.0.0.1 127.0.0.1 306
192.168.1.0 255.255.255.0 192.168.1.3 192.168.1.3 261
192.168.1.3 255.255.255.255 192.168.1.3 192.168.1.3 261
192.168.1.255 255.255.255.255 192.168.1.3 192.168.1.3 261
192.168.2.0 255.255.255.0 192.168.2.70 192.168.2.70 261
192.168.2.0 255.255.255.0 192.168.2.1 192.168.2.70 100
192.168.2.70 255.255.255.255 192.168.2.70 192.168.2.70 261
192.168.2.255 255.255.255.255 192.168.2.70 192.168.2.70 261
224.0.0.0 240.0.0.0 127.0.0.1 127.0.0.1 306
224.0.0.0 240.0.0.0 96.11.251.149 96.11.251.149 261
224.0.0.0 240.0.0.0 192.168.1.3 192.168.1.3 261
224.0.0.0 240.0.0.0 192.168.2.70 192.168.2.70 261
255.255.255.255 255.255.255.255 127.0.0.1 127.0.0.1 306
255.255.255.255 255.255.255.255 96.11.251.149 96.11.251.149 261
255.255.255.255 255.255.255.255 192.168.1.3 192.168.1.3 261
255.255.255.255 255.255.255.255 192.168.2.70 192.168.2.70 261
70 09:45:07.912 10/01/13 Sev=Info/6 CM/0x63100036
The routing table was updated for the Virtual Adapter
71 09:45:07.912 10/01/13 Sev=Info/4 CM/0x6310001A
One secure connection established
72 09:45:07.943 10/01/13 Sev=Info/4 CM/0x6310003B
Address watch added for 96.11.251.149. Current hostname: psaserver, Current address(es): 192.168.2.70, 96.11.251.149, 192.168.1.3.
73 09:45:07.943 10/01/13 Sev=Info/4 CM/0x6310003B
Address watch added for 192.168.2.70. Current hostname: psaserver, Current address(es): 192.168.2.70, 96.11.251.149, 192.168.1.3.
74 09:45:07.943 10/01/13 Sev=Info/5 CM/0x63100001
Did not find the Smartcard to watch for removal
75 09:45:07.943 10/01/13 Sev=Info/4 IPSEC/0x63700014
Deleted all keys
76 09:45:07.943 10/01/13 Sev=Info/4 IPSEC/0x63700010
Created a new key structure
77 09:45:07.943 10/01/13 Sev=Info/4 IPSEC/0x6370000F
Added key with SPI=0x1c4cafaa into key list
78 09:45:07.943 10/01/13 Sev=Info/4 IPSEC/0x63700010
Created a new key structure
79 09:45:07.943 10/01/13 Sev=Info/4 IPSEC/0x6370000F
Added key with SPI=0xc5bfbe3e into key list
80 09:45:07.943 10/01/13 Sev=Info/4 IPSEC/0x6370002F
Assigned VA private interface addr 192.168.2.70
81 09:45:07.943 10/01/13 Sev=Info/4 IPSEC/0x63700037
Configure public interface: 96.11.251.149. SG: **.**.***.***
82 09:45:07.943 10/01/13 Sev=Info/6 CM/0x63100046
Set tunnel established flag in registry to 1.
83 09:45:13.459 10/01/13 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK INFO *(HASH, NOTIFY:DPD_REQUEST) to **.**.***.***
84 09:45:13.459 10/01/13 Sev=Info/6 IKE/0x6300003D
Sending DPD request to **.**.***.***, our seq# = 107205276
85 09:45:13.474 10/01/13 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = **.**.***.***
86 09:45:13.474 10/01/13 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK INFO *(HASH, NOTIFY:DPD_ACK) from **.**.***.***
87 09:45:13.474 10/01/13 Sev=Info/5 IKE/0x63000040
Received DPD ACK from **.**.***.***, seq# received = 107205276, seq# expected = 107205276
88 09:45:15.959 10/01/13 Sev=Info/4 IPSEC/0x63700019
Activate outbound key with SPI=0x1c4cafaa for inbound key with SPI=0xc5bfbe3e
89 09:46:00.947 10/01/13 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK INFO *(HASH, NOTIFY:DPD_REQUEST) to **.**.***.***
90 09:46:00.947 10/01/13 Sev=Info/6 IKE/0x6300003D
Sending DPD request to **.**.***.***, our seq# = 107205277
91 09:46:01.529 10/01/13 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = **.**.***.***
92 09:46:01.529 10/01/13 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK INFO *(HASH, NOTIFY:DPD_ACK) from **.**.***.***
93 09:46:01.529 10/01/13 Sev=Info/5 IKE/0x63000040
Received DPD ACK from **.**.***.***, seq# received = 107205277, seq# expected = 107205277
94 09:46:11.952 10/01/13 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK INFO *(HASH, NOTIFY:DPD_REQUEST) to **.**.***.***
95 09:46:11.952 10/01/13 Sev=Info/6 IKE/0x6300003D
Sending DPD request to **.**.***.***, our seq# = 107205278
96 09:46:11.979 10/01/13 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = **.**.***.***
97 09:46:11.979 10/01/13 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK INFO *(HASH, NOTIFY:DPD_ACK) from **.**.***.***
98 09:46:11.979 10/01/13 Sev=Info/5 IKE/0x63000040
Received DPD ACK from **.**.***.***, seq# received = 107205278, seq# expected = 107205278
Any help would be appreciated, thanks!I made the change that you requested by moving the VPN pool to the 192.168.3.0 network. Unfortunately, now traffic isn't flowing to the inside network at all. I was going to make a specific route as you suggested, but as far as I can see the routes are already being created correctly on the VPN client's end.
Here is the route print off of the computer behind the (test) client:
===========================================================================
Interface List
21...00 05 9a 3c 78 00 ......Cisco Systems VPN Adapter for 64-bit Windows
10...00 15 5d 01 02 01 ......Microsoft Hyper-V Network Adapter
15...00 15 5d 01 02 02 ......Microsoft Hyper-V Network Adapter #2
1...........................Software Loopback Interface 1
13...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter
11...00 00 00 00 00 00 00 e0 Teredo Tunneling Pseudo-Interface
14...00 00 00 00 00 00 00 e0 Microsoft 6to4 Adapter
16...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter #2
23...00 00 00 00 00 00 00 e0 Microsoft ISATAP Adapter #3
===========================================================================
IPv4 Route Table
===========================================================================
Active Routes:
Network Destination Netmask Gateway Interface Metric
0.0.0.0 0.0.0.0 96.11.251.1 96.11.251.149 261
69.61.228.178 255.255.255.255 96.11.251.1 96.11.251.149 100
96.11.251.0 255.255.255.0 On-link 96.11.251.149 261
96.11.251.149 255.255.255.255 On-link 96.11.251.149 261
96.11.251.255 255.255.255.255 On-link 96.11.251.149 261
127.0.0.0 255.0.0.0 On-link 127.0.0.1 306
127.0.0.1 255.255.255.255 On-link 127.0.0.1 306
127.255.255.255 255.255.255.255 On-link 127.0.0.1 306
192.168.1.0 255.255.255.0 On-link 192.168.1.3 261
192.168.1.3 255.255.255.255 On-link 192.168.1.3 261
192.168.1.255 255.255.255.255 On-link 192.168.1.3 261
192.168.2.0 255.255.255.0 192.168.3.1 192.168.3.70 100
192.168.3.0 255.255.255.0 On-link 192.168.3.70 261
192.168.3.70 255.255.255.255 On-link 192.168.3.70 261
192.168.3.255 255.255.255.255 On-link 192.168.3.70 261
224.0.0.0 240.0.0.0 On-link 127.0.0.1 306
224.0.0.0 240.0.0.0 On-link 192.168.1.3 261
224.0.0.0 240.0.0.0 On-link 96.11.251.149 261
224.0.0.0 240.0.0.0 On-link 192.168.3.70 261
255.255.255.255 255.255.255.255 On-link 127.0.0.1 306
255.255.255.255 255.255.255.255 On-link 192.168.1.3 261
255.255.255.255 255.255.255.255 On-link 96.11.251.149 261
255.255.255.255 255.255.255.255 On-link 192.168.3.70 261
===========================================================================
Persistent Routes:
Network Address Netmask Gateway Address Metric
0.0.0.0 0.0.0.0 96.11.251.1 Default
===========================================================================
IPv6 Route Table
===========================================================================
Active Routes:
If Metric Network Destination Gateway
14 1020 ::/0 2002:c058:6301::c058:6301
14 1020 ::/0 2002:c058:6301::1
1 306 ::1/128 On-link
14 1005 2002::/16 On-link
14 261 2002:600b:fb95::600b:fb95/128
On-link
15 261 fe80::/64 On-link
10 261 fe80::/64 On-link
21 261 fe80::/64 On-link
10 261 fe80::64ae:bae7:3dc0:c8c4/128
On-link
21 261 fe80::e9f7:e24:3147:bd/128
On-link
15 261 fe80::f116:2dfd:1771:125a/128
On-link
1 306 ff00::/8 On-link
15 261 ff00::/8 On-link
10 261 ff00::/8 On-link
21 261 ff00::/8 On-link
===========================================================================
Persistent Routes:
None
And here is the updated running config in case you need it:
: Saved
ASA Version 8.4(1)
hostname NCHCO
enable password hTjwXz/V8EuTw9p9 encrypted
passwd hTjwXz/V8EuTw9p9 encrypted
names
name 192.168.2.0 NCHCO description City Offices
name 192.168.2.80 VPN_End
name 192.168.2.70 VPN_Start
interface Vlan1
nameif inside
security-level 100
ip address 192.168.2.1 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address 69.61.228.178 255.255.255.248
interface Ethernet0/0
switchport access vlan 2
speed 100
duplex full
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
boot system disk0:/asa841-k8.bin
ftp mode passive
object network NCHCO
subnet 192.168.2.0 255.255.255.0
object network obj-192.168.1.0
subnet 192.168.1.0 255.255.255.0
object network obj-192.168.2.64
subnet 192.168.2.64 255.255.255.224
object network obj-0.0.0.0
subnet 0.0.0.0 255.255.255.0
object network obj_any
subnet 0.0.0.0 0.0.0.0
object network Webserver
object network FINX
host 192.168.2.11
object service rdp
service tcp source range 1 65535 destination eq 3389
description rdp
object network obj-192.168.3.0
subnet 192.168.3.0 255.255.255.0
object network obj-192.168.2.0
subnet 192.168.2.0 255.255.255.0
access-list outside_nat0_outbound extended permit ip object NCHCO 192.168.1.0 255.255.255.0
access-list outside_nat0_outbound extended permit ip object NCHCO 192.168.2.0 255.255.255.0
access-list inside_nat0_outbound extended permit ip object NCHCO 192.168.1.0 255.255.255.0
access-list inside_nat0_outbound extended permit ip any 192.168.2.64 255.255.255.224
access-list inside_nat0_outbound extended permit ip 0.0.0.0 255.255.255.0 192.168.2.64 255.255.255.224
access-list outside_1_cryptomap extended permit ip object NCHCO 192.168.1.0 255.255.255.0
access-list outside_1_cryptomap_1 extended permit ip object NCHCO 192.168.1.0 255.255.255.0
access-list LAN_Access standard permit 192.168.2.0 255.255.255.0
access-list LAN_Access standard permit 0.0.0.0 255.255.255.0
access-list NCHCO_splitTunnelAcl_1 standard permit 192.168.2.0 255.255.255.0
access-list AnyConnect_Client_Local_Print extended permit tcp any any eq lpd
access-list AnyConnect_Client_Local_Print remark IPP: Internet Printing Protocol
access-list AnyConnect_Client_Local_Print extended permit tcp any any eq 631
access-list AnyConnect_Client_Local_Print remark Windows' printing port
access-list AnyConnect_Client_Local_Print extended permit tcp any any eq 9100
access-list AnyConnect_Client_Local_Print remark mDNS: multicast DNS protocol
access-list AnyConnect_Client_Local_Print extended permit udp any host 224.0.0.251 eq 5353
access-list AnyConnect_Client_Local_Print remark LLMNR: Link Local Multicast Name Resolution protocol
access-list AnyConnect_Client_Local_Print extended permit udp any host 224.0.0.252 eq 5355
access-list AnyConnect_Client_Local_Print remark TCP/NetBIOS protocol
access-list AnyConnect_Client_Local_Print extended permit tcp any any eq 137
access-list AnyConnect_Client_Local_Print extended permit udp any any eq netbios-ns
access-list AnyConnect_Client_Local_Print extended deny ip any any
access-list outside_access_in extended permit tcp any object FINX eq 3389
access-list outside_access_in_1 extended permit object rdp any object FINX
access-list outside_specific_blocks extended deny ip host 121.168.66.35 any
pager lines 24
logging enable
logging asdm informational
mtu inside 1500
mtu outside 1500
ip local pool VPN_Pool VPN_Start-VPN_End mask 255.255.255.0
ip local pool VPN_Split_Pool 192.168.3.70-192.168.3.80 mask 255.255.255.0
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-649.bin
no asdm history enable
arp timeout 14400
nat (inside,any) source static NCHCO NCHCO destination static obj-192.168.1.0 obj-192.168.1.0
nat (inside,any) source static any any destination static obj-192.168.2.64 obj-192.168.2.64
nat (inside,any) source static obj-0.0.0.0 obj-0.0.0.0 destination static obj-192.168.2.64 obj-192.168.2.64
object network obj_any
nat (inside,outside) dynamic interface
object network FINX
nat (inside,outside) static interface service tcp 3389 3389
access-group outside_access_in_1 in interface outside
route outside 0.0.0.0 0.0.0.0 69.61.228.177 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-record DfltAccessPolicy
network-acl outside_nat0_outbound
webvpn
svc ask enable default svc
http server enable
http 192.168.1.0 255.255.255.0 inside
http 69.61.228.178 255.255.255.255 outside
http 74.218.158.238 255.255.255.255 outside
http NCHCO 255.255.255.0 inside
http 96.11.251.186 255.255.255.255 outside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart warmstart
crypto ipsec ikev1 transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec ikev1 transform-set l2tp-transform esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set l2tp-transform mode transport
crypto ipsec ikev1 transform-set vpn-transform esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set TRANS_ESP_3DES_SHA esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set TRANS_ESP_3DES_SHA mode transport
crypto ipsec ikev1 transform-set TRANS_ESP_3DES_MD5 esp-3des esp-md5-hmac
crypto ipsec ikev1 transform-set TRANS_ESP_3DES_MD5 mode transport
crypto ipsec ikev1 transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs group1
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto dynamic-map dyn-map 10 set pfs group1
crypto dynamic-map dyn-map 10 set ikev1 transform-set l2tp-transform vpn-transform
crypto dynamic-map dyn-map 10 set reverse-route
crypto dynamic-map outside_dyn_map 20 set ikev1 transform-set ESP-3DES-SHA
crypto dynamic-map outside_dyn_map 20 set reverse-route
crypto map outside_map 1 match address outside_1_cryptomap
crypto map outside_map 1 set pfs group1
crypto map outside_map 1 set peer 74.219.208.50
crypto map outside_map 1 set ikev1 transform-set ESP-3DES-SHA
crypto map outside_map 20 ipsec-isakmp dynamic outside_dyn_map
crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map outside_map interface outside
crypto map inside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map inside_map interface inside
crypto map vpn-map 1 match address outside_1_cryptomap_1
crypto map vpn-map 1 set pfs group1
crypto map vpn-map 1 set peer 74.219.208.50
crypto map vpn-map 1 set ikev1 transform-set ESP-3DES-SHA
crypto map vpn-map 10 ipsec-isakmp dynamic dyn-map
crypto isakmp identity address
crypto ikev1 enable inside
crypto ikev1 enable outside
crypto ikev1 ipsec-over-tcp port 10000
crypto ikev1 policy 10
authentication pre-share
encryption 3des
hash md5
group 2
lifetime 86400
crypto ikev1 policy 15
authentication pre-share
encryption aes-256
hash sha
group 2
lifetime 86400
crypto ikev1 policy 35
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
client-update enable
telnet 192.168.1.0 255.255.255.0 inside
telnet NCHCO 255.255.255.0 inside
telnet timeout 5
ssh 192.168.1.0 255.255.255.0 inside
ssh NCHCO 255.255.255.0 inside
ssh 96.11.251.186 255.255.255.255 outside
ssh timeout 5
console timeout 0
dhcpd address 192.168.2.150-192.168.2.225 inside
dhcpd dns 216.68.4.10 216.68.5.10 interface inside
dhcpd lease 64000 interface inside
threat-detection basic-threat
threat-detection statistics host
threat-detection statistics port
threat-detection statistics protocol
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
group-policy DefaultRAGroup internal
group-policy DefaultRAGroup attributes
dns-server value 192.168.2.1
vpn-tunnel-protocol ikev1 l2tp-ipsec
default-domain value nchco.local
group-policy DfltGrpPolicy attributes
dns-server value 192.168.2.1
vpn-tunnel-protocol ikev1 l2tp-ipsec ssl-client ssl-clientless
password-storage enable
ipsec-udp enable
intercept-dhcp 255.255.255.0 enable
address-pools value VPN_Split_Pool
group-policy NCHCO internal
group-policy NCHCO attributes
dns-server value 192.168.2.1 8.8.8.8
vpn-tunnel-protocol ikev1
split-tunnel-policy tunnelspecified
split-tunnel-network-list value NCHCO_splitTunnelAcl_1
default-domain value NCHCO.local
username admin password LbMiJuAJjDaFb2uw encrypted privilege 15
username 8njferg password yB1lHEVmHZGj5C2Z encrypted privilege 15
username NCHvpn99 password dhn.JzttvRmMbHsP encrypted
tunnel-group DefaultRAGroup general-attributes
address-pool (inside) VPN_Pool
address-pool VPN_Split_Pool
authentication-server-group (inside) LOCAL
authentication-server-group (outside) LOCAL
authorization-server-group LOCAL
authorization-server-group (inside) LOCAL
authorization-server-group (outside) LOCAL
default-group-policy DefaultRAGroup
strip-realm
strip-group
tunnel-group DefaultRAGroup ipsec-attributes
ikev1 pre-shared-key *****
peer-id-validate nocheck
tunnel-group DefaultRAGroup ppp-attributes
no authentication chap
no authentication ms-chap-v1
authentication ms-chap-v2
tunnel-group DefaultWEBVPNGroup ppp-attributes
authentication pap
authentication ms-chap-v2
tunnel-group 74.219.208.50 type ipsec-l2l
tunnel-group 74.219.208.50 ipsec-attributes
ikev1 pre-shared-key *****
tunnel-group NCHCO type remote-access
tunnel-group NCHCO general-attributes
address-pool VPN_Split_Pool
default-group-policy NCHCO
tunnel-group NCHCO ipsec-attributes
ikev1 pre-shared-key *****
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
service-policy global_policy global
prompt hostname context
call-home
profile CiscoTAC-1
no active
destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService
destination address email [email protected]
destination transport-method http
subscribe-to-alert-group diagnostic
subscribe-to-alert-group environment
subscribe-to-alert-group inventory periodic monthly
subscribe-to-alert-group configuration periodic monthly
subscribe-to-alert-group telemetry periodic daily
Cryptochecksum:9e8466cd318c0bd35bc660fa65ba7a03
: end
asdm image disk0:/asdm-649.bin
asdm location VPN_Start 255.255.255.255 inside
asdm location VPN_End 255.255.255.255 inside
no asdm history enable
Thanks again for your help,
Matthew -
Problem with Remote Access VPN on ASA 5505
I am currently having an issue configuring an ASA 5505 to connect via remote access VPN using the Cisco VPN Client 5.0.07.0440 running on Windows 8 Pro x64. The VPN client prompts for the username and password during the connect process, but fails soon after.
The VPN client logs are as follows:
Cisco Systems VPN Client Version 5.0.07.0440
Copyright (C) 1998-2010 Cisco Systems, Inc. All Rights Reserved.
Client Type(s): Windows, WinNT
Running on: 6.2.9200
2 15:09:21.240 12/11/12 Sev=Info/4 CM/0x63100002
Begin connection process
3 15:09:21.287 12/11/12 Sev=Info/4 CM/0x63100004
Establish secure connection
4 15:09:21.287 12/11/12 Sev=Info/4 CM/0x63100024
Attempt connection with server "**.**.***.***"
5 15:09:21.287 12/11/12 Sev=Info/6 IKE/0x6300003B
Attempting to establish a connection with **.**.***.***.
6 15:09:21.287 12/11/12 Sev=Info/4 IKE/0x63000001
Starting IKE Phase 1 Negotiation
7 15:09:21.303 12/11/12 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK AG (SA, KE, NON, ID, VID(Xauth), VID(dpd), VID(Frag), VID(Nat-T), VID(Unity)) to **.**.***.***
8 15:09:21.365 12/11/12 Sev=Info/6 GUI/0x63B00012
Authentication request attributes is 6h.
9 15:09:21.334 12/11/12 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = **.**.***.***
10 15:09:21.334 12/11/12 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK AG (SA, KE, NON, ID, HASH, VID(Unity), VID(Xauth), VID(dpd), VID(Nat-T), NAT-D, NAT-D, VID(Frag), VID(?)) from **.**.***.***
11 15:09:21.334 12/11/12 Sev=Info/5 IKE/0x63000001
Peer is a Cisco-Unity compliant peer
12 15:09:21.334 12/11/12 Sev=Info/5 IKE/0x63000001
Peer supports XAUTH
13 15:09:21.334 12/11/12 Sev=Info/5 IKE/0x63000001
Peer supports DPD
14 15:09:21.334 12/11/12 Sev=Info/5 IKE/0x63000001
Peer supports NAT-T
15 15:09:21.334 12/11/12 Sev=Info/5 IKE/0x63000001
Peer supports IKE fragmentation payloads
16 15:09:21.334 12/11/12 Sev=Info/6 IKE/0x63000001
IOS Vendor ID Contruction successful
17 15:09:21.334 12/11/12 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK AG *(HASH, NOTIFY:STATUS_INITIAL_CONTACT, NAT-D, NAT-D, VID(?), VID(Unity)) to **.**.***.***
18 15:09:21.334 12/11/12 Sev=Info/6 IKE/0x63000055
Sent a keepalive on the IPSec SA
19 15:09:21.334 12/11/12 Sev=Info/4 IKE/0x63000083
IKE Port in use - Local Port = 0xFBCE, Remote Port = 0x1194
20 15:09:21.334 12/11/12 Sev=Info/5 IKE/0x63000072
Automatic NAT Detection Status:
Remote end is NOT behind a NAT device
This end IS behind a NAT device
21 15:09:21.334 12/11/12 Sev=Info/4 CM/0x6310000E
Established Phase 1 SA. 1 Crypto Active IKE SA, 0 User Authenticated IKE SA in the system
22 15:09:21.365 12/11/12 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = **.**.***.***
23 15:09:21.365 12/11/12 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK TRANS *(HASH, ATTR) from **.**.***.***
24 15:09:21.365 12/11/12 Sev=Info/4 CM/0x63100015
Launch xAuth application
25 15:09:21.474 12/11/12 Sev=Info/4 IPSEC/0x63700008
IPSec driver successfully started
26 15:09:21.474 12/11/12 Sev=Info/4 IPSEC/0x63700014
Deleted all keys
27 15:09:27.319 12/11/12 Sev=Info/4 CM/0x63100017
xAuth application returned
28 15:09:27.319 12/11/12 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK TRANS *(HASH, ATTR) to **.**.***.***
29 15:09:27.365 12/11/12 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = **.**.***.***
30 15:09:27.365 12/11/12 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK TRANS *(HASH, ATTR) from **.**.***.***
31 15:09:27.365 12/11/12 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK TRANS *(HASH, ATTR) to **.**.***.***
32 15:09:27.365 12/11/12 Sev=Info/4 CM/0x6310000E
Established Phase 1 SA. 1 Crypto Active IKE SA, 1 User Authenticated IKE SA in the system
33 15:09:27.365 12/11/12 Sev=Info/5 IKE/0x6300005E
Client sending a firewall request to concentrator
34 15:09:27.365 12/11/12 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK TRANS *(HASH, ATTR) to **.**.***.***
35 15:09:27.397 12/11/12 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = **.**.***.***
36 15:09:27.397 12/11/12 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK TRANS *(HASH, ATTR) from **.**.***.***
37 15:09:27.397 12/11/12 Sev=Info/5 IKE/0x63000010
MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_ADDRESS: , value = 192.168.2.70
38 15:09:27.397 12/11/12 Sev=Info/5 IKE/0x63000010
MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_NETMASK: , value = 255.255.255.0
39 15:09:27.397 12/11/12 Sev=Info/5 IKE/0x63000010
MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_DNS(1): , value = 192.168.2.1
40 15:09:27.397 12/11/12 Sev=Info/5 IKE/0x63000010
MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_DNS(2): , value = 8.8.8.8
41 15:09:27.397 12/11/12 Sev=Info/5 IKE/0x6300000D
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_SAVEPWD: , value = 0x00000001
42 15:09:27.397 12/11/12 Sev=Info/5 IKE/0x6300000E
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_DEFDOMAIN: , value = NCHCO
43 15:09:27.397 12/11/12 Sev=Info/5 IKE/0x6300000D
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_PFS: , value = 0x00000000
44 15:09:27.397 12/11/12 Sev=Info/5 IKE/0x6300000E
MODE_CFG_REPLY: Attribute = APPLICATION_VERSION, value = Cisco Systems, Inc ASA5505 Version 8.2(5) built by builders on Fri 20-May-11 16:00
45 15:09:27.397 12/11/12 Sev=Info/5 IKE/0x6300000D
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_SMARTCARD_REMOVAL_DISCONNECT: , value = 0x00000001
46 15:09:27.397 12/11/12 Sev=Info/5 IKE/0x6300000D
MODE_CFG_REPLY: Attribute = Received and using NAT-T port number , value = 0x00001194
47 15:09:27.397 12/11/12 Sev=Info/4 CM/0x63100019
Mode Config data received
48 15:09:27.412 12/11/12 Sev=Info/4 IKE/0x63000056
Received a key request from Driver: Local IP = 192.168.2.70, GW IP = **.**.***.***, Remote IP = 0.0.0.0
49 15:09:27.412 12/11/12 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK QM *(HASH, SA, NON, ID, ID) to **.**.***.***
50 15:09:27.444 12/11/12 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = **.**.***.***
51 15:09:27.444 12/11/12 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK INFO *(HASH, NOTIFY:STATUS_RESP_LIFETIME) from **.**.***.***
52 15:09:27.444 12/11/12 Sev=Info/5 IKE/0x63000045
RESPONDER-LIFETIME notify has value of 86400 seconds
53 15:09:27.444 12/11/12 Sev=Info/5 IKE/0x63000047
This SA has already been alive for 6 seconds, setting expiry to 86394 seconds from now
54 15:09:27.459 12/11/12 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = **.**.***.***
55 15:09:27.459 12/11/12 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK INFO *(HASH, NOTIFY:NO_PROPOSAL_CHOSEN) from **.**.***.***
56 15:09:27.459 12/11/12 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK INFO *(HASH, DEL) to **.**.***.***
57 15:09:27.459 12/11/12 Sev=Info/4 IKE/0x63000049
Discarding IPsec SA negotiation, MsgID=CE99A8A8
58 15:09:27.459 12/11/12 Sev=Info/4 IKE/0x63000017
Marking IKE SA for deletion (I_Cookie=A3A341F1C7606AD5 R_Cookie=F1F403018625E924) reason = DEL_REASON_IKE_NEG_FAILED
59 15:09:27.459 12/11/12 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = **.**.***.***
60 15:09:27.459 12/11/12 Sev=Info/4 IKE/0x63000058
Received an ISAKMP message for a non-active SA, I_Cookie=A3A341F1C7606AD5 R_Cookie=F1F403018625E924
61 15:09:27.459 12/11/12 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK INFO *(Dropped) from **.**.***.***
62 15:09:27.490 12/11/12 Sev=Info/4 IPSEC/0x63700014
Deleted all keys
63 15:09:30.475 12/11/12 Sev=Info/4 IKE/0x6300004B
Discarding IKE SA negotiation (I_Cookie=A3A341F1C7606AD5 R_Cookie=F1F403018625E924) reason = DEL_REASON_IKE_NEG_FAILED
64 15:09:30.475 12/11/12 Sev=Info/4 CM/0x63100012
Phase 1 SA deleted before first Phase 2 SA is up cause by "DEL_REASON_IKE_NEG_FAILED". 0 Crypto Active IKE SA, 0 User Authenticated IKE SA in the system
65 15:09:30.475 12/11/12 Sev=Info/5 CM/0x63100025
Initializing CVPNDrv
66 15:09:30.475 12/11/12 Sev=Info/6 CM/0x63100046
Set tunnel established flag in registry to 0.
67 15:09:30.475 12/11/12 Sev=Info/4 IKE/0x63000001
IKE received signal to terminate VPN connection
68 15:09:30.475 12/11/12 Sev=Info/4 IPSEC/0x63700014
Deleted all keys
69 15:09:30.475 12/11/12 Sev=Info/4 IPSEC/0x63700014
Deleted all keys
70 15:09:30.475 12/11/12 Sev=Info/4 IPSEC/0x63700014
Deleted all keys
71 15:09:30.475 12/11/12 Sev=Info/4 IPSEC/0x6370000A
IPSec driver successfully stopped
The running configuration is as follows (there is a site-to-site VPN set up as well to another ASA 5505, but that is working flawlessly):
: Saved
ASA Version 8.2(5)
hostname NCHCO
enable password hTjwXz/V8EuTw9p9 encrypted
passwd hTjwXz/V8EuTw9p9 encrypted
names
name 192.168.2.0 NCHCO description City Offices
name 192.168.2.80 VPN_End
name 192.168.2.70 VPN_Start
interface Ethernet0/0
switchport access vlan 2
speed 100
duplex full
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
interface Vlan1
nameif inside
security-level 100
ip address 192.168.2.1 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address **.**.***.*** 255.255.255.248
boot system disk0:/asa825-k8.bin
ftp mode passive
access-list outside_nat0_outbound extended permit ip NCHCO 255.255.255.0 192.168.1.0 255.255.255.0
access-list inside_nat0_outbound extended permit ip NCHCO 255.255.255.0 192.168.1.0 255.255.255.0
access-list inside_nat0_outbound extended permit ip any 192.168.2.64 255.255.255.224
access-list outside_1_cryptomap extended permit ip NCHCO 255.255.255.0 192.168.1.0 255.255.255.0
access-list outside_1_cryptomap_1 extended permit ip NCHCO 255.255.255.0 192.168.1.0 255.255.255.0
access-list LAN_Access standard permit NCHCO 255.255.255.0
access-list LAN_Access standard permit 0.0.0.0 255.255.255.0
pager lines 24
logging enable
logging asdm informational
mtu inside 1500
mtu outside 1500
ip local pool VPN_Pool VPN_Start-VPN_End mask 255.255.255.0
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-645.bin
no asdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 0 access-list inside_nat0_outbound
nat (inside) 1 0.0.0.0 0.0.0.0
nat (outside) 0 access-list outside_nat0_outbound
route outside 0.0.0.0 0.0.0.0 74.219.208.49 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
network-acl outside_nat0_outbound
webvpn
svc ask enable default svc
http server enable
http 192.168.1.0 255.255.255.0 inside
http **.**.***.*** 255.255.255.255 outside
http 74.218.158.238 255.255.255.255 outside
http NCHCO 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec transform-set l2tp-transform esp-3des esp-sha-hmac
crypto ipsec transform-set l2tp-transform mode transport
crypto ipsec transform-set vpn-transform esp-aes-256 esp-sha-hmac
crypto ipsec transform-set TRANS_ESP_3DES_SHA esp-3des esp-sha-hmac
crypto ipsec transform-set TRANS_ESP_3DES_SHA mode transport
crypto ipsec transform-set TRANS_ESP_3DES_MD5 esp-3des esp-md5-hmac
crypto ipsec transform-set TRANS_ESP_3DES_MD5 mode transport
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs group1
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto dynamic-map dyn-map 10 set pfs group1
crypto dynamic-map dyn-map 10 set transform-set l2tp-transform vpn-transform
crypto dynamic-map dyn-map 10 set reverse-route
crypto dynamic-map outside_dyn_map 20 set transform-set TRANS_ESP_3DES_MD5
crypto map outside_map 1 match address outside_1_cryptomap
crypto map outside_map 1 set pfs group1
crypto map outside_map 1 set peer 74.219.208.50
crypto map outside_map 1 set transform-set ESP-3DES-SHA
crypto map outside_map 20 ipsec-isakmp dynamic outside_dyn_map
crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map outside_map interface outside
crypto map inside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map inside_map interface inside
crypto map vpn-map 1 match address outside_1_cryptomap_1
crypto map vpn-map 1 set pfs group1
crypto map vpn-map 1 set peer 74.219.208.50
crypto map vpn-map 1 set transform-set ESP-3DES-SHA
crypto map vpn-map 10 ipsec-isakmp dynamic dyn-map
crypto isakmp identity address
crypto isakmp enable inside
crypto isakmp enable outside
crypto isakmp policy 10
authentication pre-share
encryption 3des
hash md5
group 2
lifetime 86400
crypto isakmp policy 15
authentication pre-share
encryption aes-256
hash sha
group 2
lifetime 86400
crypto isakmp policy 35
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
crypto isakmp ipsec-over-tcp port 10000
client-update enable
telnet 192.168.1.0 255.255.255.0 inside
telnet NCHCO 255.255.255.0 inside
telnet timeout 5
ssh 192.168.1.0 255.255.255.0 inside
ssh NCHCO 255.255.255.0 inside
ssh timeout 5
console timeout 0
dhcpd address 192.168.2.150-192.168.2.225 inside
dhcpd dns 216.68.4.10 216.68.5.10 interface inside
dhcpd lease 64000 interface inside
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
group-policy DefaultRAGroup internal
group-policy DefaultRAGroup attributes
dns-server value 192.168.2.1
vpn-tunnel-protocol IPSec l2tp-ipsec
default-domain value nchco.local
group-policy DfltGrpPolicy attributes
dns-server value 192.168.2.1
vpn-tunnel-protocol IPSec l2tp-ipsec svc webvpn
password-storage enable
ipsec-udp enable
intercept-dhcp 255.255.255.0 enable
address-pools value VPN_Pool
group-policy NCHVPN internal
group-policy NCHVPN attributes
dns-server value 192.168.2.1 8.8.8.8
vpn-tunnel-protocol IPSec l2tp-ipsec
default-domain value NCHCO
username admin password LbMiJuAJjDaFb2uw encrypted privilege 15
username 8njferg password yB1lHEVmHZGj5C2Z encrypted privilege 15
username NCHvpn99 password QhZZtJfwbnowceB7 encrypted
tunnel-group DefaultRAGroup general-attributes
address-pool (inside) VPN_Pool
address-pool VPN_Pool
authentication-server-group (inside) LOCAL
authentication-server-group (outside) LOCAL
authorization-server-group LOCAL
authorization-server-group (inside) LOCAL
authorization-server-group (outside) LOCAL
default-group-policy DefaultRAGroup
strip-realm
strip-group
tunnel-group DefaultRAGroup ipsec-attributes
pre-shared-key *****
peer-id-validate nocheck
tunnel-group DefaultRAGroup ppp-attributes
no authentication chap
no authentication ms-chap-v1
authentication ms-chap-v2
tunnel-group DefaultWEBVPNGroup ppp-attributes
authentication pap
authentication ms-chap-v2
tunnel-group 74.219.208.50 type ipsec-l2l
tunnel-group 74.219.208.50 ipsec-attributes
pre-shared-key *****
tunnel-group NCHVPN type remote-access
tunnel-group NCHVPN general-attributes
address-pool VPN_Pool
default-group-policy NCHVPN
tunnel-group NCHVPN ipsec-attributes
pre-shared-key *****
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
service-policy global_policy global
prompt hostname context
no call-home reporting anonymous
Cryptochecksum:15852745977ff159ba808c4a4feb61fa
: end
asdm image disk0:/asdm-645.bin
asdm location VPN_Start 255.255.255.255 inside
asdm location VPN_End 255.255.255.255 inside
no asdm history enable
Anyone have any idea why this is happening?
Thanks!Thanks again for your reply, and sorry about the late response, havent gotten back to this issue until just now. I applied the above command as you specified, and unfortunately, it did not resolve the problem. Below are the logs from the VPN Client for the connection + attempted browsing of a network share that is behind the ASA, and the new running configuration.
VPN Client Log:
Cisco Systems VPN Client Version 5.0.07.0440
Copyright (C) 1998-2010 Cisco Systems, Inc. All Rights Reserved.
Client Type(s): Windows, WinNT
Running on: 6.2.9200
331 13:11:41.362 12/17/12 Sev=Info/4 CM/0x63100002
Begin connection process
332 13:11:41.362 12/17/12 Sev=Info/4 CM/0x63100004
Establish secure connection
333 13:11:41.362 12/17/12 Sev=Info/4 CM/0x63100024
Attempt connection with server "69.61.228.178"
334 13:11:41.362 12/17/12 Sev=Info/6 IKE/0x6300003B
Attempting to establish a connection with 69.61.228.178.
335 13:11:41.362 12/17/12 Sev=Info/4 IKE/0x63000001
Starting IKE Phase 1 Negotiation
336 13:11:41.424 12/17/12 Sev=Info/6 GUI/0x63B00012
Authentication request attributes is 6h.
337 13:11:41.362 12/17/12 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK AG (SA, KE, NON, ID, VID(Xauth), VID(dpd), VID(Frag), VID(Nat-T), VID(Unity)) to 69.61.228.178
338 13:11:41.393 12/17/12 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = 69.61.228.178
339 13:11:41.393 12/17/12 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK AG (SA, KE, NON, ID, HASH, VID(Unity), VID(Xauth), VID(dpd), VID(Nat-T), NAT-D, NAT-D, VID(Frag), VID(?)) from 69.61.228.178
340 13:11:41.393 12/17/12 Sev=Info/5 IKE/0x63000001
Peer is a Cisco-Unity compliant peer
341 13:11:41.393 12/17/12 Sev=Info/5 IKE/0x63000001
Peer supports XAUTH
342 13:11:41.393 12/17/12 Sev=Info/5 IKE/0x63000001
Peer supports DPD
343 13:11:41.393 12/17/12 Sev=Info/5 IKE/0x63000001
Peer supports NAT-T
344 13:11:41.393 12/17/12 Sev=Info/5 IKE/0x63000001
Peer supports IKE fragmentation payloads
345 13:11:41.393 12/17/12 Sev=Info/6 IKE/0x63000001
IOS Vendor ID Contruction successful
346 13:11:41.393 12/17/12 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK AG *(HASH, NOTIFY:STATUS_INITIAL_CONTACT, NAT-D, NAT-D, VID(?), VID(Unity)) to 69.61.228.178
347 13:11:41.393 12/17/12 Sev=Info/6 IKE/0x63000055
Sent a keepalive on the IPSec SA
348 13:11:41.393 12/17/12 Sev=Info/4 IKE/0x63000083
IKE Port in use - Local Port = 0xD271, Remote Port = 0x1194
349 13:11:41.393 12/17/12 Sev=Info/5 IKE/0x63000072
Automatic NAT Detection Status:
Remote end is NOT behind a NAT device
This end IS behind a NAT device
350 13:11:41.393 12/17/12 Sev=Info/4 CM/0x6310000E
Established Phase 1 SA. 1 Crypto Active IKE SA, 0 User Authenticated IKE SA in the system
351 13:11:41.424 12/17/12 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = 69.61.228.178
352 13:11:41.424 12/17/12 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK TRANS *(HASH, ATTR) from 69.61.228.178
353 13:11:41.424 12/17/12 Sev=Info/4 CM/0x63100015
Launch xAuth application
354 13:11:41.424 12/17/12 Sev=Info/4 CM/0x63100017
xAuth application returned
355 13:11:41.424 12/17/12 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK TRANS *(HASH, ATTR) to 69.61.228.178
356 13:11:41.456 12/17/12 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = 69.61.228.178
357 13:11:41.456 12/17/12 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK TRANS *(HASH, ATTR) from 69.61.228.178
358 13:11:41.456 12/17/12 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK TRANS *(HASH, ATTR) to 69.61.228.178
359 13:11:41.456 12/17/12 Sev=Info/4 CM/0x6310000E
Established Phase 1 SA. 1 Crypto Active IKE SA, 1 User Authenticated IKE SA in the system
360 13:11:41.456 12/17/12 Sev=Info/5 IKE/0x6300005E
Client sending a firewall request to concentrator
361 13:11:41.456 12/17/12 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK TRANS *(HASH, ATTR) to 69.61.228.178
362 13:11:41.502 12/17/12 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = 69.61.228.178
363 13:11:41.502 12/17/12 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK TRANS *(HASH, ATTR) from 69.61.228.178
364 13:11:41.502 12/17/12 Sev=Info/5 IKE/0x63000010
MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_ADDRESS: , value = 192.168.2.70
365 13:11:41.502 12/17/12 Sev=Info/5 IKE/0x63000010
MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_NETMASK: , value = 255.255.255.0
366 13:11:41.502 12/17/12 Sev=Info/5 IKE/0x63000010
MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_DNS(1): , value = 192.168.2.1
367 13:11:41.502 12/17/12 Sev=Info/5 IKE/0x63000010
MODE_CFG_REPLY: Attribute = INTERNAL_IPV4_DNS(2): , value = 8.8.8.8
368 13:11:41.502 12/17/12 Sev=Info/5 IKE/0x6300000D
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_SAVEPWD: , value = 0x00000001
369 13:11:41.502 12/17/12 Sev=Info/5 IKE/0x6300000D
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_SPLIT_INCLUDE (# of split_nets), value = 0x00000001
370 13:11:41.502 12/17/12 Sev=Info/5 IKE/0x6300000F
SPLIT_NET #1
subnet = 192.168.2.0
mask = 255.255.255.0
protocol = 0
src port = 0
dest port=0
371 13:11:41.502 12/17/12 Sev=Info/5 IKE/0x6300000E
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_DEFDOMAIN: , value = NCHCO.local
372 13:11:41.502 12/17/12 Sev=Info/5 IKE/0x6300000D
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_PFS: , value = 0x00000000
373 13:11:41.502 12/17/12 Sev=Info/5 IKE/0x6300000E
MODE_CFG_REPLY: Attribute = APPLICATION_VERSION, value = Cisco Systems, Inc ASA5505 Version 8.4(1) built by builders on Mon 31-Jan-11 02:11
374 13:11:41.502 12/17/12 Sev=Info/5 IKE/0x6300000D
MODE_CFG_REPLY: Attribute = MODECFG_UNITY_SMARTCARD_REMOVAL_DISCONNECT: , value = 0x00000001
375 13:11:41.502 12/17/12 Sev=Info/5 IKE/0x6300000D
MODE_CFG_REPLY: Attribute = Received and using NAT-T port number , value = 0x00001194
376 13:11:41.502 12/17/12 Sev=Info/4 CM/0x63100019
Mode Config data received
377 13:11:41.502 12/17/12 Sev=Info/4 IKE/0x63000056
Received a key request from Driver: Local IP = 192.168.2.70, GW IP = 69.61.228.178, Remote IP = 0.0.0.0
378 13:11:41.502 12/17/12 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK QM *(HASH, SA, NON, ID, ID) to 69.61.228.178
379 13:11:41.534 12/17/12 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = 69.61.228.178
380 13:11:41.534 12/17/12 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK INFO *(HASH, NOTIFY:STATUS_RESP_LIFETIME) from 69.61.228.178
381 13:11:41.534 12/17/12 Sev=Info/5 IKE/0x63000045
RESPONDER-LIFETIME notify has value of 86400 seconds
382 13:11:41.534 12/17/12 Sev=Info/5 IKE/0x63000047
This SA has already been alive for 0 seconds, setting expiry to 86400 seconds from now
383 13:11:41.549 12/17/12 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = 69.61.228.178
384 13:11:41.549 12/17/12 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK QM *(HASH, SA, NON, ID, ID, NOTIFY:STATUS_RESP_LIFETIME) from 69.61.228.178
385 13:11:41.549 12/17/12 Sev=Info/5 IKE/0x63000045
RESPONDER-LIFETIME notify has value of 28800 seconds
386 13:11:41.549 12/17/12 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK QM *(HASH) to 69.61.228.178
387 13:11:41.549 12/17/12 Sev=Info/5 IKE/0x63000059
Loading IPsec SA (MsgID=C4F5B5A6 OUTBOUND SPI = 0xD2DBADEA INBOUND SPI = 0x14762837)
388 13:11:41.549 12/17/12 Sev=Info/5 IKE/0x63000025
Loaded OUTBOUND ESP SPI: 0xD2DBADEA
389 13:11:41.549 12/17/12 Sev=Info/5 IKE/0x63000026
Loaded INBOUND ESP SPI: 0x14762837
390 13:11:41.549 12/17/12 Sev=Info/5 CVPND/0x63400013
Destination Netmask Gateway Interface Metric
0.0.0.0 0.0.0.0 192.168.1.1 192.168.1.162 10
127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 306
127.0.0.1 255.255.255.255 127.0.0.1 127.0.0.1 306
127.255.255.255 255.255.255.255 127.0.0.1 127.0.0.1 306
192.168.1.0 255.255.255.0 192.168.1.162 192.168.1.162 266
192.168.1.162 255.255.255.255 192.168.1.162 192.168.1.162 266
192.168.1.255 255.255.255.255 192.168.1.162 192.168.1.162 266
224.0.0.0 240.0.0.0 127.0.0.1 127.0.0.1 306
224.0.0.0 240.0.0.0 192.168.1.162 192.168.1.162 266
255.255.255.255 255.255.255.255 127.0.0.1 127.0.0.1 306
255.255.255.255 255.255.255.255 192.168.1.162 192.168.1.162 266
391 13:11:41.877 12/17/12 Sev=Info/6 CVPND/0x63400001
Launch VAInst64 to control IPSec Virtual Adapter
392 13:11:43.455 12/17/12 Sev=Info/4 CM/0x63100034
The Virtual Adapter was enabled:
IP=192.168.2.70/255.255.255.0
DNS=192.168.2.1,8.8.8.8
WINS=0.0.0.0,0.0.0.0
Domain=NCHCO.local
Split DNS Names=
393 13:11:43.455 12/17/12 Sev=Info/5 CVPND/0x63400013
Destination Netmask Gateway Interface Metric
0.0.0.0 0.0.0.0 192.168.1.1 192.168.1.162 10
127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 306
127.0.0.1 255.255.255.255 127.0.0.1 127.0.0.1 306
127.255.255.255 255.255.255.255 127.0.0.1 127.0.0.1 306
192.168.1.0 255.255.255.0 192.168.1.162 192.168.1.162 266
192.168.1.162 255.255.255.255 192.168.1.162 192.168.1.162 266
192.168.1.255 255.255.255.255 192.168.1.162 192.168.1.162 266
224.0.0.0 240.0.0.0 127.0.0.1 127.0.0.1 306
224.0.0.0 240.0.0.0 192.168.1.162 192.168.1.162 266
224.0.0.0 240.0.0.0 0.0.0.0 0.0.0.0 266
255.255.255.255 255.255.255.255 127.0.0.1 127.0.0.1 306
255.255.255.255 255.255.255.255 192.168.1.162 192.168.1.162 266
255.255.255.255 255.255.255.255 0.0.0.0 0.0.0.0 266
394 13:11:47.517 12/17/12 Sev=Info/4 CM/0x63100038
Successfully saved route changes to file.
395 13:11:47.517 12/17/12 Sev=Info/5 CVPND/0x63400013
Destination Netmask Gateway Interface Metric
0.0.0.0 0.0.0.0 192.168.1.1 192.168.1.162 10
69.61.228.178 255.255.255.255 192.168.1.1 192.168.1.162 100
127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 306
127.0.0.1 255.255.255.255 127.0.0.1 127.0.0.1 306
127.255.255.255 255.255.255.255 127.0.0.1 127.0.0.1 306
192.168.1.0 255.255.255.0 192.168.1.162 192.168.1.162 266
192.168.1.2 255.255.255.255 192.168.1.162 192.168.1.162 100
192.168.1.162 255.255.255.255 192.168.1.162 192.168.1.162 266
192.168.1.255 255.255.255.255 192.168.1.162 192.168.1.162 266
192.168.2.0 255.255.255.0 192.168.2.70 192.168.2.70 266
192.168.2.0 255.255.255.0 192.168.2.1 192.168.2.70 100
192.168.2.70 255.255.255.255 192.168.2.70 192.168.2.70 266
192.168.2.255 255.255.255.255 192.168.2.70 192.168.2.70 266
224.0.0.0 240.0.0.0 127.0.0.1 127.0.0.1 306
224.0.0.0 240.0.0.0 192.168.1.162 192.168.1.162 266
224.0.0.0 240.0.0.0 192.168.2.70 192.168.2.70 266
255.255.255.255 255.255.255.255 127.0.0.1 127.0.0.1 306
255.255.255.255 255.255.255.255 192.168.1.162 192.168.1.162 266
255.255.255.255 255.255.255.255 192.168.2.70 192.168.2.70 266
396 13:11:47.517 12/17/12 Sev=Info/6 CM/0x63100036
The routing table was updated for the Virtual Adapter
397 13:11:47.517 12/17/12 Sev=Info/4 CM/0x6310001A
One secure connection established
398 13:11:47.517 12/17/12 Sev=Info/4 CM/0x6310003B
Address watch added for 192.168.1.162. Current hostname: MATT-PC, Current address(es): 192.168.2.70, 192.168.1.162.
399 13:11:47.517 12/17/12 Sev=Info/4 CM/0x6310003B
Address watch added for 192.168.2.70. Current hostname: MATT-PC, Current address(es): 192.168.2.70, 192.168.1.162.
400 13:11:47.517 12/17/12 Sev=Info/5 CM/0x63100001
Did not find the Smartcard to watch for removal
401 13:11:47.517 12/17/12 Sev=Info/4 IPSEC/0x63700008
IPSec driver successfully started
402 13:11:47.517 12/17/12 Sev=Info/4 IPSEC/0x63700014
Deleted all keys
403 13:11:47.517 12/17/12 Sev=Info/6 IPSEC/0x6370002C
Sent 109 packets, 0 were fragmented.
404 13:11:47.517 12/17/12 Sev=Info/4 IPSEC/0x63700014
Deleted all keys
405 13:11:47.517 12/17/12 Sev=Info/4 IPSEC/0x63700010
Created a new key structure
406 13:11:47.517 12/17/12 Sev=Info/4 IPSEC/0x6370000F
Added key with SPI=0xeaaddbd2 into key list
407 13:11:47.517 12/17/12 Sev=Info/4 IPSEC/0x63700010
Created a new key structure
408 13:11:47.517 12/17/12 Sev=Info/4 IPSEC/0x6370000F
Added key with SPI=0x37287614 into key list
409 13:11:47.517 12/17/12 Sev=Info/4 IPSEC/0x6370002F
Assigned VA private interface addr 192.168.2.70
410 13:11:47.517 12/17/12 Sev=Info/4 IPSEC/0x63700037
Configure public interface: 192.168.1.162. SG: 69.61.228.178
411 13:11:47.517 12/17/12 Sev=Info/6 CM/0x63100046
Set tunnel established flag in registry to 1.
412 13:11:52.688 12/17/12 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK INFO *(HASH, NOTIFY:DPD_REQUEST) to 69.61.228.178
413 13:11:52.688 12/17/12 Sev=Info/6 IKE/0x6300003D
Sending DPD request to 69.61.228.178, our seq# = 2722476009
414 13:11:52.704 12/17/12 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = 69.61.228.178
415 13:11:52.704 12/17/12 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK INFO *(HASH, NOTIFY:DPD_ACK) from 69.61.228.178
416 13:11:52.704 12/17/12 Sev=Info/5 IKE/0x63000040
Received DPD ACK from 69.61.228.178, seq# received = 2722476009, seq# expected = 2722476009
417 13:12:03.187 12/17/12 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK INFO *(HASH, NOTIFY:DPD_REQUEST) to 69.61.228.178
418 13:12:03.187 12/17/12 Sev=Info/6 IKE/0x6300003D
Sending DPD request to 69.61.228.178, our seq# = 2722476010
419 13:12:03.202 12/17/12 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = 69.61.228.178
420 13:12:03.202 12/17/12 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK INFO *(HASH, NOTIFY:DPD_ACK) from 69.61.228.178
421 13:12:03.202 12/17/12 Sev=Info/5 IKE/0x63000040
Received DPD ACK from 69.61.228.178, seq# received = 2722476010, seq# expected = 2722476010
422 13:12:14.185 12/17/12 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK INFO *(HASH, NOTIFY:DPD_REQUEST) to 69.61.228.178
423 13:12:14.185 12/17/12 Sev=Info/6 IKE/0x6300003D
Sending DPD request to 69.61.228.178, our seq# = 2722476011
424 13:12:14.201 12/17/12 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = 69.61.228.178
425 13:12:14.201 12/17/12 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK INFO *(HASH, NOTIFY:DPD_ACK) from 69.61.228.178
426 13:12:14.201 12/17/12 Sev=Info/5 IKE/0x63000040
Received DPD ACK from 69.61.228.178, seq# received = 2722476011, seq# expected = 2722476011
427 13:12:24.762 12/17/12 Sev=Info/4 IKE/0x63000013
SENDING >>> ISAKMP OAK INFO *(HASH, NOTIFY:DPD_REQUEST) to 69.61.228.178
428 13:12:24.762 12/17/12 Sev=Info/6 IKE/0x6300003D
Sending DPD request to 69.61.228.178, our seq# = 2722476012
429 13:12:24.778 12/17/12 Sev=Info/5 IKE/0x6300002F
Received ISAKMP packet: peer = 69.61.228.178
430 13:12:24.778 12/17/12 Sev=Info/4 IKE/0x63000014
RECEIVING <<< ISAKMP OAK INFO *(HASH, NOTIFY:DPD_ACK) from 69.61.228.178
431 13:12:24.778 12/17/12 Sev=Info/5 IKE/0x63000040
Received DPD ACK from 69.61.228.178, seq# received = 2722476012, seq# expected = 2722476012
New running configuration:
: Saved
ASA Version 8.4(1)
hostname NCHCO
enable password hTjwXz/V8EuTw9p9 encrypted
passwd hTjwXz/V8EuTw9p9 encrypted
names
name 192.168.2.0 NCHCO description City Offices
name 192.168.2.80 VPN_End
name 192.168.2.70 VPN_Start
interface Vlan1
nameif inside
security-level 100
ip address 192.168.2.1 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address 69.61.228.178 255.255.255.248
interface Ethernet0/0
switchport access vlan 2
speed 100
duplex full
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
boot system disk0:/asa841-k8.bin
ftp mode passive
object network NCHCO
subnet 192.168.2.0 255.255.255.0
object network obj-192.168.1.0
subnet 192.168.1.0 255.255.255.0
object network obj-192.168.2.64
subnet 192.168.2.64 255.255.255.224
object network obj-0.0.0.0
subnet 0.0.0.0 255.255.255.0
object network obj_any
subnet 0.0.0.0 0.0.0.0
access-list outside_nat0_outbound extended permit ip object NCHCO 192.168.1.0 255.255.255.0
access-list outside_nat0_outbound extended permit ip object NCHCO 192.168.2.0 255.255.255.0
access-list inside_nat0_outbound extended permit ip object NCHCO 192.168.1.0 255.255.255.0
access-list inside_nat0_outbound extended permit ip any 192.168.2.64 255.255.255.224
access-list inside_nat0_outbound extended permit ip 0.0.0.0 255.255.255.0 192.168.2.64 255.255.255.224
access-list outside_1_cryptomap extended permit ip object NCHCO 192.168.1.0 255.255.255.0
access-list outside_1_cryptomap_1 extended permit ip object NCHCO 192.168.1.0 255.255.255.0
access-list LAN_Access standard permit 192.168.2.0 255.255.255.0
access-list LAN_Access standard permit 0.0.0.0 255.255.255.0
access-list NCHCO_splitTunnelAcl_1 standard permit 192.168.2.0 255.255.255.0
access-list AnyConnect_Client_Local_Print extended deny ip any any
access-list AnyConnect_Client_Local_Print extended permit tcp any any eq lpd
access-list AnyConnect_Client_Local_Print remark IPP: Internet Printing Protocol
access-list AnyConnect_Client_Local_Print extended permit tcp any any eq 631
access-list AnyConnect_Client_Local_Print remark Windows' printing port
access-list AnyConnect_Client_Local_Print extended permit tcp any any eq 9100
access-list AnyConnect_Client_Local_Print remark mDNS: multicast DNS protocol
access-list AnyConnect_Client_Local_Print extended permit udp any host 224.0.0.251 eq 5353
access-list AnyConnect_Client_Local_Print remark LLMNR: Link Local Multicast Name Resolution protocol
access-list AnyConnect_Client_Local_Print extended permit udp any host 224.0.0.252 eq 5355
access-list AnyConnect_Client_Local_Print remark TCP/NetBIOS protocol
access-list AnyConnect_Client_Local_Print extended permit tcp any any eq 137
access-list AnyConnect_Client_Local_Print extended permit udp any any eq netbios-ns
pager lines 24
logging enable
logging asdm informational
mtu inside 1500
mtu outside 1500
ip local pool VPN_Pool VPN_Start-VPN_End mask 255.255.255.0
icmp unreachable rate-limit 1 burst-size 1
asdm image disk0:/asdm-649.bin
no asdm history enable
arp timeout 14400
nat (inside,any) source static NCHCO NCHCO destination static obj-192.168.1.0 obj-192.168.1.0
nat (inside,any) source static any any destination static obj-192.168.2.64 obj-192.168.2.64
nat (inside,any) source static obj-0.0.0.0 obj-0.0.0.0 destination static obj-192.168.2.64 obj-192.168.2.64
object network obj_any
nat (inside,outside) dynamic interface
route outside 0.0.0.0 0.0.0.0 69.61.228.177 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-record DfltAccessPolicy
network-acl outside_nat0_outbound
webvpn
svc ask enable default svc
http server enable
http 192.168.1.0 255.255.255.0 inside
http 69.61.228.178 255.255.255.255 outside
http 74.218.158.238 255.255.255.255 outside
http NCHCO 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec ikev1 transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec ikev1 transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec ikev1 transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec ikev1 transform-set l2tp-transform esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set l2tp-transform mode transport
crypto ipsec ikev1 transform-set vpn-transform esp-aes-256 esp-sha-hmac
crypto ipsec ikev1 transform-set TRANS_ESP_3DES_SHA esp-3des esp-sha-hmac
crypto ipsec ikev1 transform-set TRANS_ESP_3DES_SHA mode transport
crypto ipsec ikev1 transform-set TRANS_ESP_3DES_MD5 esp-3des esp-md5-hmac
crypto ipsec ikev1 transform-set TRANS_ESP_3DES_MD5 mode transport
crypto ipsec ikev1 transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs group1
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set ikev1 transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto dynamic-map dyn-map 10 set pfs group1
crypto dynamic-map dyn-map 10 set ikev1 transform-set l2tp-transform vpn-transform
crypto dynamic-map dyn-map 10 set reverse-route
crypto dynamic-map outside_dyn_map 20 set ikev1 transform-set ESP-3DES-SHA
crypto map outside_map 1 match address outside_1_cryptomap
crypto map outside_map 1 set pfs group1
crypto map outside_map 1 set peer 74.219.208.50
crypto map outside_map 1 set ikev1 transform-set ESP-3DES-SHA
crypto map outside_map 20 ipsec-isakmp dynamic outside_dyn_map
crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map outside_map interface outside
crypto map inside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map inside_map interface inside
crypto map vpn-map 1 match address outside_1_cryptomap_1
crypto map vpn-map 1 set pfs group1
crypto map vpn-map 1 set peer 74.219.208.50
crypto map vpn-map 1 set ikev1 transform-set ESP-3DES-SHA
crypto map vpn-map 10 ipsec-isakmp dynamic dyn-map
crypto isakmp identity address
crypto ikev1 enable inside
crypto ikev1 enable outside
crypto ikev1 ipsec-over-tcp port 10000
crypto ikev1 policy 10
authentication pre-share
encryption 3des
hash md5
group 2
lifetime 86400
crypto ikev1 policy 15
authentication pre-share
encryption aes-256
hash sha
group 2
lifetime 86400
crypto ikev1 policy 35
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
client-update enable
telnet 192.168.1.0 255.255.255.0 inside
telnet NCHCO 255.255.255.0 inside
telnet timeout 5
ssh 192.168.1.0 255.255.255.0 inside
ssh NCHCO 255.255.255.0 inside
ssh timeout 5
console timeout 0
dhcpd address 192.168.2.150-192.168.2.225 inside
dhcpd dns 216.68.4.10 216.68.5.10 interface inside
dhcpd lease 64000 interface inside
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
group-policy DefaultRAGroup internal
group-policy DefaultRAGroup attributes
dns-server value 192.168.2.1
vpn-tunnel-protocol ikev1 l2tp-ipsec
default-domain value nchco.local
group-policy DfltGrpPolicy attributes
dns-server value 192.168.2.1
vpn-tunnel-protocol ikev1 l2tp-ipsec ssl-client ssl-clientless
password-storage enable
ipsec-udp enable
intercept-dhcp 255.255.255.0 enable
address-pools value VPN_Pool
group-policy NCHCO internal
group-policy NCHCO attributes
dns-server value 192.168.2.1 8.8.8.8
vpn-tunnel-protocol ikev1
split-tunnel-policy tunnelspecified
split-tunnel-network-list value NCHCO_splitTunnelAcl_1
default-domain value NCHCO.local
username admin password LbMiJuAJjDaFb2uw encrypted privilege 15
username 8njferg password yB1lHEVmHZGj5C2Z encrypted privilege 15
username NCHvpn99 password dhn.JzttvRmMbHsP encrypted
tunnel-group DefaultRAGroup general-attributes
address-pool (inside) VPN_Pool
address-pool VPN_Pool
authentication-server-group (inside) LOCAL
authentication-server-group (outside) LOCAL
authorization-server-group LOCAL
authorization-server-group (inside) LOCAL
authorization-server-group (outside) LOCAL
default-group-policy DefaultRAGroup
strip-realm
strip-group
tunnel-group DefaultRAGroup ipsec-attributes
ikev1 pre-shared-key *****
peer-id-validate nocheck
tunnel-group DefaultRAGroup ppp-attributes
no authentication chap
no authentication ms-chap-v1
authentication ms-chap-v2
tunnel-group DefaultWEBVPNGroup ppp-attributes
authentication pap
authentication ms-chap-v2
tunnel-group 74.219.208.50 type ipsec-l2l
tunnel-group 74.219.208.50 ipsec-attributes
ikev1 pre-shared-key *****
tunnel-group NCHCO type remote-access
tunnel-group NCHCO general-attributes
address-pool VPN_Pool
default-group-policy NCHCO
tunnel-group NCHCO ipsec-attributes
ikev1 pre-shared-key *****
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
service-policy global_policy global
prompt hostname context
call-home
profile CiscoTAC-1
no active
destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService
destination address email [email protected]
destination transport-method http
subscribe-to-alert-group diagnostic
subscribe-to-alert-group environment
subscribe-to-alert-group inventory periodic monthly
subscribe-to-alert-group configuration periodic monthly
subscribe-to-alert-group telemetry periodic daily
Cryptochecksum:b6ce58676b6aaeba48caacbeefea53a5
: end
asdm image disk0:/asdm-649.bin
asdm location VPN_Start 255.255.255.255 inside
asdm location VPN_End 255.255.255.255 inside
no asdm history enable
I'm at a loss myself as to why this isn't working, and i'm sure that you are running out of solutions yourself. Any other ideas? I really need to get this working.
Thanks so much!
Matthew -
How can I remotely access my computer from a different location on Apple Remote Desktop?
I downloaded Apple Remote Desktop and am trying to access our computer at our church that is in the auditorium and work on slides for ProPresenter from my office which is on a different network. The Mac Pro, which is in the auditorium, is connected to a Netgear wireless router. I would also want to be able to have access to observe and control the screen on the Mac Pro whether I am in my office or at my house. I have tried everything from going to portforward.com, followed those instructions, did port forwarding, used ipchicken.com to get my external IP and made sure that the Mac Pro had a static internal IP address and made sure the computer had access for remote management. Any help to resolve this issue would be greatly appreciated! Works fine when it is on the same wireless network, but I need access being on a different wireless network. Thanks!
Hi austinmac14,
So the steps listed bellow assume some things. They assume that the Airport Extreme Router your configuring is connected directly to the internet connection. And that the Airport Extreme is the only router between your computers and the internet.
That means we're talking about say a DSL modem plugged directly into the Airport Extreme, or a cable modem. in ether case, this assumes that said modem, is not acting as an internet router.
If your modem has multiple ethernet ports on it, or has a little antenna sticking out of it, then your modem is probable also a router, and these steps listed bellow will probable not work.
Also these steps are so one person, can connect to one computer at your work.
Open Airport Utility:
go to the dock
Click on the finder
go to the menu bar
Click on the "Go" menu
Chose "Utilities" from the "Go" Menu
double Click on "AirPort Utility"
Access the Base Station:
Double Click on your Airport Extreme BaseStation that is your internet connection router.
a new window should pop up with your Airport Base Station as the Window Name
Configure Static Address for the computer you want to connect to via ARD:
Click on the internet Icon from the toolbar
Click on the "DHCP" tab
For "DHCP Reservations:" Click on the "+" button
For the "Description" put "ARD"
For "Reserve Address by:" set "DHCP Client ID"
Click the "Continue" button
For "DHCP Client ID:" set "ARD"
write down the number in "IPv4" address field
Click the "Done" Button
Configure routing to ARD computer:
Click on the "Advanced" icon from the tool bar.
Click on the "Port Mapping" tab
Click on the "+" button
for "Service:" Chose "Apple Remote Desktop"
for "Private IP Address:" copy the exact IP address you wrote down in step "3. 8)"
Click the "Continue" button
Click the "Done" button
Click the "+" button
For the pulldown menu "Service:" Chose "Remote Apple Events"
for "Private IP Address:" copy the exact IP address you wrote down in step "3. 8."
Click the "Continue" button
Click the "Done" button
Click the "+" button
For the pulldown menu "Service:" Chose "Remote Login - SSH"
for "Private IP Address:" copy the exact IP address you wrote down in step "3. 8."
Click the "Continue" button
Click the "Done" button
Click the "Update" button.
wait for the Airport Extreme to update, and for your computer to reconnect to the airport extreme. (make sure you can load and browse websites.)
Configure the ARD computer to use the correct IP address:
Go to the computer you want to be able to remotely connect to
On that computer, Go to the menu bar
Chose the "Apple" menu bar
Chose "System Preferences…"
Click on the "Show All" button
Click on the "Network" icon
For the active network connection, (the connection on the left side with the green dot), click on it
Clock on the "Advanced…" button
Click on the "TCP/IP" tab
for the "DHCP Cient ID: field put "ARD".
Click the "OK" button
Click the "Apply" buttonNOTE: Under "Status" you should see "(connection name) is connected to (airport base station name) and has the IP address (IP address)." the "(IP address)" address displayed should match the IP address you wrote down in step "3. 8."
Find out what your public internet IP address is.
On the computer you wish to connect to over the internet, gotohttp://whatismyipaddress.com/
when the web page loads, you should see "IP Information:" fallow by a number like 192.168.0.1, write down what ever number it is.
At this point you should be able to connect to the computer remotely
connect to the internet from another location.
open Apple Remote Desktop
go to the file menu
chose connect to computer using ip address
set the address to the address to the IP address you wrote down for step 6. 2.
use the same password as you used to connect to the computer at work using ARD.
So here the catch. If your router gets reset... well then your going to have to configure it again. Also all the same rules you have to connect to the computer at work, also apply to connecting to the computer from over the local network. That means your computer need to be on or sleeping. And if it's sleeping it need to be configure to wake for network access.
Also some network connections change. When it comes to internet connections, some connections are static IP, while other connections are DHCP. If your connection is static... great! if it's DHCP, your address may change. If it dose.. well then your ability to connect will break. And then you'd have to do step 6 & 7 again.
Of corse there are ways around this. But that's kind of another conversation.
Some internet locations may block your ability to connect to your computer at work. This is very common at schools, and companies. Basically any place that tries to control your ability to browse the internet, may block remote access to computers; because a remote computer would completely by pass their web filter.
ALSO there is an easier option. As far as setup. There are programs designed to make remotely accessing your mac as easy as possible. For instance there is LogMeIn or Slack. With both of these programs, it's simple. make sure your computer is always on. Then install the software. Create an account with the service. And then you can connect to the computer almost any where by going to their website.
This option requires no router configuration. It handles DHCP. It's designed to work in as many locations as possible. -
I need a remote access application
I need a remote access application for my Mac OS X 10.5.8 so that when I'm at my home office I can access my remote business office network that uses PCs. Is there an application I can download to do this? Is Microsoft Remote Desktop Connection for Mac what I need? I am not a technical person at all so I need something simple.
You didn't specify what kind access? Control and observe or just simple file sharing/access.
How do you plan on getting into your office's network? do you have a VPN setup? If not, are the correct ports open and forwarded on the main router?
Lots of unknown variables here. Without knowing what's in place it'll be hard to steer you in the right direction once you figure out what type of access you need.
If Microsoft's Remote Desktop Connection is definitely what you want to use, then please post further question on Microsoft's own forums for their Mac software, as Apple discussions only provide support for Apple products: http://www.officeformac.com/productforums -
Remote Access VPN Clients Cannot Access inside LAN
I have been asked to set up remote access VPN on an ASA 5505 that I previously had no invlovement with. I have set it up the VPN using the wizard, they way I normally do, but the clients have no access to anything in the inside subnet, not even the inside interface IP address of the ASA. Thay can ping each other. The remote access policy below that I am working on is labeled VPNPHONE, address pool 172.16.20.1-10. I do not need split tunneling to be enabled. The active WAN interface is the one labeled outside_cable.
: Saved
ASA Version 8.2(1)
hostname ASA5505
domain-name default.domain.invalid
enable password eelnBRz68aYSzHyz encrypted
passwd eelnBRz68aYSzHyz encrypted
names
interface Vlan1
nameif inside
security-level 100
ip address 192.168.100.1 255.255.255.0
interface Vlan2
nameif outside
security-level 0
pppoe client vpdn group dataDSL
ip address 76.244.75.57 255.255.255.255 pppoe
interface Vlan3
nameif dmz
security-level 50
ip address 192.168.9.1 255.255.255.0
interface Vlan10
nameif outside_cable
security-level 0
ip address 50.84.96.178 255.255.255.240
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
switchport access vlan 10
interface Ethernet0/2
switchport access vlan 3
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
ftp mode passive
clock timezone CST -6
clock summer-time CDT recurring
dns server-group DefaultDNS
domain-name default.domain.invalid
same-security-traffic permit intra-interface
object-group service Netbios udp
port-object eq 139
port-object eq 445
port-object eq netbios-ns
object-group service Netbios_TCP tcp
port-object eq 445
port-object eq netbios-ssn
object-group network DM_INLINE_NETWORK_1
network-object host 192.168.100.177
network-object host 192.168.100.249
object-group service Web_Services tcp
port-object eq ftp
port-object eq ftp-data
port-object eq www
port-object eq https
object-group network DM_INLINE_NETWORK_10
network-object host 192.168.9.10
network-object host 192.168.9.4
object-group network DM_INLINE_NETWORK_11
network-object host 192.168.9.10
network-object host 192.168.9.4
object-group network DM_INLINE_NETWORK_2
network-object host 192.168.9.10
network-object host 192.168.9.4
object-group network DM_INLINE_NETWORK_3
network-object host 192.168.9.10
network-object host 192.168.9.4
object-group network DM_INLINE_NETWORK_4
network-object host 192.168.9.10
network-object host 192.168.9.4
object-group network DM_INLINE_NETWORK_5
network-object host 192.168.9.10
network-object host 192.168.9.4
object-group network DM_INLINE_NETWORK_6
network-object host 192.168.9.10
network-object host 192.168.9.4
object-group network DM_INLINE_NETWORK_7
network-object host 192.168.9.10
network-object host 192.168.9.4
object-group network DM_INLINE_NETWORK_8
network-object host 192.168.9.10
network-object host 192.168.9.4
object-group network DM_INLINE_NETWORK_9
network-object host 192.168.9.10
network-object host 192.168.9.4
object-group network VPN
network-object 192.168.255.0 255.255.255.0
access-list outside_access_in extended permit icmp any host 76.244.75.61
access-list outside_access_in extended permit tcp any host 76.244.75.61 eq ftp
access-list outside_access_in extended permit tcp any host 76.244.75.61 eq ftp-data
access-list outside_access_in extended permit tcp any host 76.244.75.62 eq www
access-list outside_access_in extended permit tcp any host 76.244.75.62 eq https
access-list outside_access_in extended permit tcp any host 76.244.75.59 eq www
access-list outside_access_in extended permit tcp any host 76.244.75.59 eq https
access-list outside_access_in extended permit tcp any host 76.244.75.60 eq www
access-list outside_access_in extended permit tcp any host 76.244.75.60 eq https
access-list outside_access_in extended permit tcp any host 76.244.75.58 eq www
access-list outside_access_in extended permit tcp any host 76.244.75.58 eq https
access-list dmz_access_in remark Quickbooks
access-list dmz_access_in extended permit tcp object-group DM_INLINE_NETWORK_6 host 192.168.100.5 eq 56719
access-list dmz_access_in remark Quickbooks range
access-list dmz_access_in extended permit tcp object-group DM_INLINE_NETWORK_7 host 192.168.100.5 range 55333 55337
access-list dmz_access_in extended permit udp object-group DM_INLINE_NETWORK_8 host 192.168.100.5 eq 1434
access-list dmz_access_in extended permit tcp object-group DM_INLINE_NETWORK_9 host 192.168.100.5 eq 49398
access-list dmz_access_in remark QB
access-list dmz_access_in extended permit tcp object-group DM_INLINE_NETWORK_10 host 192.168.100.5 eq 8019
access-list dmz_access_in extended permit udp object-group DM_INLINE_NETWORK_2 host 192.168.100.5 eq 2638
access-list dmz_access_in extended permit udp object-group DM_INLINE_NETWORK_11 host 192.168.100.5 object-group Netbios
access-list dmz_access_in extended permit tcp object-group DM_INLINE_NETWORK_3 host 192.168.100.5 object-group Netbios_TCP
access-list dmz_access_in extended deny ip host 192.168.9.4 host 192.168.100.5 inactive
access-list dmz_access_in extended permit udp object-group DM_INLINE_NETWORK_4 any
access-list dmz_access_in extended permit tcp object-group DM_INLINE_NETWORK_5 any
access-list dmz_access_in remark Printer
access-list dmz_access_in extended permit ip 192.168.9.0 255.255.255.0 object-group DM_INLINE_NETWORK_1
access-list dmz_access_in extended permit tcp 192.168.9.0 255.255.255.0 any object-group Web_Services
access-list dmz_access_in extended permit udp 192.168.9.0 255.255.255.0 any eq domain
access-list dmz_access_in extended permit icmp 192.168.9.0 255.255.255.0 192.168.255.0 255.255.255.0 echo-reply
access-list dmz_access_in extended permit icmp 192.168.9.0 255.255.255.0 192.168.100.0 255.255.255.0 echo-reply log disable
access-list dmz_access_in remark QB probably does not need any udp
access-list dmz_access_in extended permit udp host 192.168.9.4 host 192.168.100.5 eq 55333 inactive
access-list dmz_access_in remark QB included in other rule range
access-list dmz_access_in extended permit tcp host 192.168.9.4 host 192.168.100.5 eq 55333 inactive
access-list dmz_access_in remark May be required for Quickbooks
access-list dmz_access_in extended permit icmp host 192.168.9.4 host 192.168.100.5
access-list CAD_capture extended permit ip host 192.168.9.4 host 192.168.100.5
access-list CAD_capture extended permit ip host 192.168.100.5 host 192.168.9.4
access-list inside_nat0_outbound extended permit ip any 192.168.255.0 255.255.255.0
access-list inside_nat0_outbound extended permit ip any 192.168.255.0 255.255.255.240
access-list inside_nat0_outbound extended permit ip any 172.16.10.0 255.255.255.240
access-list inside_nat0_outbound extended permit ip any 172.16.20.0 255.255.255.240
access-list cad_supplies_RAVPN_splitTunnelAcl standard permit 192.168.100.0 255.255.255.0
access-list cad_supplies_RAVPN_splitTunnelAcl standard permit 192.168.9.0 255.255.255.0
access-list dmz_nat0_outbound extended permit ip any 192.168.255.0 255.255.255.0
access-list outside_cable_access_in extended permit icmp any host 50.84.96.182
access-list outside_cable_access_in extended permit tcp any host 50.84.96.182 eq ftp
access-list outside_cable_access_in extended permit tcp any host 50.84.96.182 eq ftp-data
access-list outside_cable_access_in extended permit tcp any host 50.84.96.183 eq www
access-list outside_cable_access_in extended permit tcp any host 50.84.96.183 eq https
access-list outside_cable_access_in extended permit tcp any host 50.84.96.180 eq www
access-list outside_cable_access_in extended permit tcp any host 50.84.96.180 eq https
access-list outside_cable_access_in extended permit tcp any host 50.84.96.181 eq www
access-list outside_cable_access_in extended permit tcp any host 50.84.96.181 eq https
access-list outside_cable_access_in extended permit tcp any host 50.84.96.179 eq www
access-list outside_cable_access_in extended permit tcp any host 50.84.96.179 eq https
access-list Local_LAN_Access standard permit host 0.0.0.0
access-list vpnusers_spitTunnelACL extended permit ip 192.168.100.0 255.255.255.0 any
access-list nonat-in extended permit ip 192.168.100.0 255.255.255.0 172.16.20.0 255.255.255.0
pager lines 24
logging enable
logging buffered informational
logging asdm informational
mtu inside 1500
mtu outside 1500
mtu dmz 1500
mtu outside_cable 1500
ip local pool VPN_IP_range 192.168.255.1-192.168.255.10 mask 255.255.255.0
ip local pool VPN_Phone 172.16.20.1-172.16.20.10 mask 255.255.255.0
no failover
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
nat-control
global (outside) 10 interface
global (outside_cable) 10 interface
nat (inside) 0 access-list nonat-in
nat (inside) 10 0.0.0.0 0.0.0.0
nat (dmz) 0 access-list dmz_nat0_outbound
nat (dmz) 10 0.0.0.0 0.0.0.0
static (inside,outside) 76.244.75.62 192.168.100.25 netmask 255.255.255.255 dns
static (dmz,outside) 76.244.75.61 192.168.9.123 netmask 255.255.255.255 dns
static (dmz,outside) 76.244.75.59 192.168.9.124 netmask 255.255.255.255 dns
static (dmz,outside) 76.244.75.58 192.168.9.4 netmask 255.255.255.255 dns
static (inside,dmz) 192.168.100.0 192.168.100.0 netmask 255.255.255.0
static (dmz,outside) 76.244.75.60 192.168.9.10 netmask 255.255.255.255 dns
static (inside,outside_cable) 50.84.96.183 192.168.100.25 netmask 255.255.255.255 dns
static (dmz,outside_cable) 50.84.96.182 192.168.9.123 netmask 255.255.255.255 dns
static (dmz,outside_cable) 50.84.96.180 192.168.9.124 netmask 255.255.255.255 dns
static (dmz,outside_cable) 50.84.96.179 192.168.9.4 netmask 255.255.255.255 dns
static (dmz,outside_cable) 50.84.96.181 192.168.9.10 netmask 255.255.255.255 dns
access-group outside_access_in in interface outside
access-group dmz_access_in in interface dmz
access-group outside_cable_access_in in interface outside_cable
route outside_cable 0.0.0.0 0.0.0.0 50.84.96.177 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-record DfltAccessPolicy
http server enable
http 192.168.1.0 255.255.255.0 inside
http 192.168.100.0 255.255.255.0 inside
http 204.107.173.0 255.255.255.0 outside
http 204.107.173.0 255.255.255.0 outside_cable
http 0.0.0.0 0.0.0.0 outside_cable
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec transform-set TRANS_ESP_3DES_SHA esp-3des esp-sha-hmac
crypto ipsec transform-set TRANS_ESP_3DES_SHA mode transport
crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto map outside_cable_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map outside_cable_map interface outside_cable
crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map outside_map interface outside
crypto map inside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map inside_map interface inside
crypto isakmp enable inside
crypto isakmp enable outside
crypto isakmp enable outside_cable
crypto isakmp policy 10
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
crypto isakmp policy 30
authentication pre-share
encryption 3des
hash md5
group 2
lifetime 86400
telnet 192.168.100.0 255.255.255.0 inside
telnet timeout 5
ssh 192.168.100.0 255.255.255.0 inside
ssh 204.107.173.0 255.255.255.0 outside
ssh 204.107.173.0 255.255.255.0 outside_cable
ssh 0.0.0.0 0.0.0.0 outside_cable
ssh timeout 15
console timeout 0
vpdn group dataDSL request dialout pppoe
vpdn group dataDSL localname [email protected]
vpdn group dataDSL ppp authentication pap
vpdn username [email protected] password *********
dhcpd address 192.168.100.30-192.168.100.99 inside
dhcpd dns 192.168.100.5 68.94.156.1 interface inside
threat-detection basic-threat
threat-detection statistics port
threat-detection statistics protocol
threat-detection statistics access-list
threat-detection statistics tcp-intercept rate-interval 30 burst-rate 400 average-rate 200
webvpn
group-policy DefaultRAGroup internal
group-policy DefaultRAGroup attributes
dns-server value 192.168.100.5
vpn-tunnel-protocol IPSec l2tp-ipsec
group-policy cad_supplies_RAVPN internal
group-policy cad_supplies_RAVPN attributes
vpn-tunnel-protocol IPSec
split-tunnel-policy tunnelspecified
split-tunnel-network-list value cad_supplies_RAVPN_splitTunnelAcl
group-policy VPNPHONE internal
group-policy VPNPHONE attributes
dns-server value 192.168.100.5
vpn-tunnel-protocol IPSec
split-tunnel-policy excludespecified
split-tunnel-network-list value Local_LAN_Access
client-firewall none
client-access-rule none
username swinc password BlhBNWfh7XoeHcQC encrypted
username swinc attributes
vpn-group-policy cad_supplies_RAVPN
username meredithp password L3lRjzwb7TnwOyZ1 encrypted
username meredithp attributes
vpn-group-policy cad_supplies_RAVPN
service-type remote-access
username ipphone1 password LOjpmeIOshVdCSOU encrypted privilege 0
username ipphone1 attributes
vpn-group-policy VPNPHONE
username ipphone2 password LOjpmeIOshVdCSOU encrypted privilege 0
username ipphone2 attributes
vpn-group-policy VPNPHONE
username ipphone3 password LOjpmeIOshVdCSOU encrypted privilege 0
username ipphone3 attributes
vpn-group-policy VPNPHONE
username oethera password WKJxJq7L6wmktFNt encrypted
username oethera attributes
vpn-group-policy cad_supplies_RAVPN
service-type remote-access
username markh password nqH+bk6vj0fR83ai0SAxkg== nt-encrypted
username markh attributes
vpn-group-policy cad_supplies_RAVPN
tunnel-group DefaultRAGroup general-attributes
default-group-policy DefaultRAGroup
tunnel-group DefaultRAGroup ipsec-attributes
pre-shared-key *
tunnel-group DefaultRAGroup ppp-attributes
authentication ms-chap-v2
tunnel-group cad_supplies_RAVPN type remote-access
tunnel-group cad_supplies_RAVPN general-attributes
address-pool VPN_IP_range
default-group-policy cad_supplies_RAVPN
tunnel-group cad_supplies_RAVPN ipsec-attributes
pre-shared-key *
tunnel-group VPNPHONE type remote-access
tunnel-group VPNPHONE general-attributes
address-pool VPN_Phone
default-group-policy VPNPHONE
tunnel-group VPNPHONE ipsec-attributes
pre-shared-key *
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum 1500
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
service-policy global_policy global
prompt hostname context
Cryptochecksum:8b25ecc61861a2baa6d2556a3679cc7c
: endHi,
You have your "group-policy" set so that you have excluding some networks from being tunneled.
In this access-list named Local_LAN_Access you specify "0.0.0.0"
Doesnt this mean you are excluding all networks from being tunneled? In other words no traffic goes to your tunnel.
This access-list should only contain your local LAN network from where you are connecting with the VPN Client. If you dont need to access anything on your local LAN while having the VPN on, you don't even need this setting on. You could just tunnel all traffic instead of excluding some networks.
- Jouni -
How to set up my elderly parent with Mac so that I can use remote access to help her?
I want to set my elderly mother up with a new Mac mini so that I can use remote access to show her how use email, browse the internet, share photos. (She lives in KY, I live in OR)
She has had an iPhone and an iPad for about 6 months and she can barely use them without becoming frustrated. I want to be able to see her screen with her and show her how to do things.
My plan is to set her up with a Mac mini and I'll use my MacBookAir to remote into her system. I'm buying the mini to configure and then I'll mail it to her.
My question is whether to try to use Back to My Mac or Teamviewer for remote access
I have broadband with comcast and she has broadband with Access Cable. Each have their company modem/routers--neither of us have Airport Express.
I have my own iCloud account and she has her own. If I use Back to My Mac, it seems that I would need to set up a separate account on my Mac that would sync to her iCloud account.
Teamviewer seems easier because I don't have to use a separate account. Any advice? Anything that I'm not thinking about?As Linc says, you can establish a Screen Sharing session via iMessage and Facetime. The advantage of these 2 approaches is that once your Mom gets used to using them, she will be more comfortable using them to communicate with you. I've talked to my Mom via iChat (aka iMessage) more since she learned to use them, then in all the years before that (including when I was a child ). And just being able to see your Mom via Facetime can be useful when you want to gage how she is doing.
However, if you are any distance from your Mom, they you want backup methods incase something goes wrong.
So beside iMessage/Facetime, the next best would be Back-to-My-Mac via iCloud, however, you will want to establish her Mac as using your account so that you have the right to take control remotely.
An alternative that does not mix up your iCloud acounts would be to use TeamViewer.com (which has an unattended mode so you can do off-hour maintenance when your Mom is not around; or check up on her to find out if she is dating - Turns out if I had been paying attention, I would not have been blind-sided by my Mom getting Married again last Summer - she is in her 80's! ).
LogMeIn.com, as dwb says, can be used the same was as TeamViewer.com
Both LogMeIn.com and TeamViewer.com are very good at making it easy to get through the home router and if you are having any problems connecting using other Methods, TeamViewer.com or LogMeIn.com will most likely not have any issues.
Back-to-My-Mac allows screen sharing and file sharing so you can transfer files as well as control the screen.
Screen Sharing via Messages allows cooperative file transfer. That is to say, you can try pushing a file to your Mom, but she has to accept each transfer.
TeamViewer.com has an unattended file transfer mode.
LogMeIn.com requires the paid version to transfer files. However, there are other ways to transfer files, such as downloading them from the original source on your Mom's system while using screen sharing, using Dropbox (or similar), emailing them, etc...
Of course if you are really network savvy, you can roll your own via ssh tunnels, port forwarding routers, getting dynamic DNS names, transferring files via scp, or tunneling AFP file sharing, tunneling your screen sharing sessions. Lots of fun and excitement playing with terminal commands -
Remote Access VPN (ipsec) can ping LAN interface of firewall but not clients on the company network.
The VPN will connect.
I can ping and connect to the ASA 5510 on it's LAN interface.
My problem is that I cannot ping or access anything on the LAN past the firewall. What am I doing wrong?
Here is my config.
Result of the command: "show config"
: Saved
: Written by enable_15 at 22:55:02.299 UTC Tue Jan 10 2012
ASA Version 8.2(5)
hostname ********
enable password UbBnTPKwu27ohfYB encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
interface Ethernet0/0
nameif outside
security-level 0
ip address x.x.x.x x.x.x.x
interface Ethernet0/1
nameif inside
security-level 100
ip address 10.0.4.1 255.255.255.0
interface Ethernet0/2
shutdown
no nameif
no security-level
no ip address
interface Ethernet0/3
shutdown
no nameif
no security-level
no ip address
interface Management0/0
nameif management
security-level 100
ip address 192.168.1.1 255.255.255.0
management-only
ftp mode passive
same-security-traffic permit inter-interface
same-security-traffic permit intra-interface
object-group network BC
network-object 10.0.3.0 255.255.255.0
network-object 10.0.4.0 255.255.255.0
access-list outside_access_in extended permit tcp any any eq ssh
access-list outside_access_in extended permit tcp any any eq 50000
access-list outside_access_in extended permit tcp any any eq 3390
access-list outside_access_in extended permit tcp any any eq 8066
access-list outside_access_in extended permit tcp any any eq 22225
access-list outside_access_in extended permit tcp any any eq 1600
access-list outside_access_in extended permit tcp any any eq 37260
access-list outside_access_in extended permit tcp any any eq 37261
access-list outside_access_in extended permit tcp any any eq 37262
access-list outside_access_in extended permit tcp any any eq 37263
access-list outside_access_in extended permit tcp any any eq 37264
access-list outside_access_in extended permit tcp any any eq 1435
access-list outside_access_in extended permit tcp any any eq 250
access-list outside_access_in extended permit tcp any any eq citrix-ica
access-list outside_access_in extended permit tcp any any eq 8080
access-list outside_access_in extended permit tcp any any eq www
access-list outside_access_in extended permit tcp any any eq 85
access-list outside_access_in extended permit tcp any any eq 8069
access-list outside_access_in extended permit tcp any any eq 3389
access-list outside_access_in extended permit tcp any any eq 23032
access-list outside_access_in extended permit tcp any any eq 32023
access-list outside_access_in extended permit tcp any any eq 3399
access-list outside_access_in extended permit udp any any eq 250
access-list outside_access_in extended permit udp any any eq 5008
access-list outside_access_in extended permit icmp any any
access-list splittunn-ppso extended permit ip 10.0.4.0 255.255.255.0 10.10.10.0 255.255.255.0
access-list splittunn-ppso extended permit ip 10.0.3.0 255.255.255.0 10.10.10.0 255.255.255.0
access-list nonat extended permit ip 10.0.4.0 255.255.255.0 10.10.10.0 255.255.255.0
access-list nonat extended permit ip 10.0.3.0 255.255.255.0 10.10.10.0 255.255.255.0
pager lines 24
logging asdm informational
mtu outside 1500
mtu inside 1500
mtu management 1500
ip local pool vpn-pool 10.10.10.1-10.10.10.254 mask 255.255.255.0
icmp unreachable rate-limit 1 burst-size 1
icmp permit any outside
icmp permit any inside
no asdm history enable
arp timeout 14400
nat-control
global (outside) 101 interface
nat (inside) 0 access-list nonat
nat (inside) 101 0.0.0.0 0.0.0.0
static (inside,outside) tcp interface 50000 10.0.4.58 50000 netmask 255.255.255.255
static (inside,outside) tcp interface ssh 10.0.4.7 ssh netmask 255.255.255.255
static (inside,outside) tcp interface 3390 10.0.3.249 3390 netmask 255.255.255.255
static (inside,outside) tcp interface 8066 10.0.3.249 8066 netmask 255.255.255.255
static (inside,outside) tcp interface 22225 10.0.4.58 22225 netmask 255.255.255.255
static (inside,outside) tcp interface 1600 10.0.4.58 1600 netmask 255.255.255.255
static (inside,outside) tcp interface 37260 10.0.4.58 37260 netmask 255.255.255.255
static (inside,outside) tcp interface 37261 10.0.4.58 37261 netmask 255.255.255.255
static (inside,outside) tcp interface 37262 10.0.4.58 37262 netmask 255.255.255.255
static (inside,outside) tcp interface 37263 10.0.4.58 37263 netmask 255.255.255.255
static (inside,outside) tcp interface 37264 10.0.4.58 37264 netmask 255.255.255.255
static (inside,outside) tcp interface 1433 10.0.4.240 1433 netmask 255.255.255.255
static (inside,outside) udp interface 5008 10.0.4.240 5008 netmask 255.255.255.255
static (inside,outside) udp interface 249 10.0.4.240 249 netmask 255.255.255.255
static (inside,outside) tcp interface 250 10.0.4.240 250 netmask 255.255.255.255
static (inside,outside) tcp interface www 10.0.4.15 www netmask 255.255.255.255
static (inside,outside) tcp interface citrix-ica 10.0.4.15 citrix-ica netmask 255.255.255.255
static (inside,outside) tcp interface 8080 10.0.4.15 8080 netmask 255.255.255.255
static (inside,outside) tcp interface 85 10.0.4.15 85 netmask 255.255.255.255
static (inside,outside) tcp interface 8069 10.0.4.236 8069 netmask 255.255.255.255
static (inside,outside) tcp interface 3399 10.0.4.236 3389 netmask 255.255.255.255
static (inside,outside) tcp interface 23032 10.0.4.244 23032 netmask 255.255.255.255
static (inside,outside) tcp interface 32023 10.0.4.244 32023 netmask 255.255.255.255
access-group outside_access_in in interface outside
route outside 0.0.0.0 0.0.0.0 x.x.x.x 1
route inside 10.0.3.0 255.255.255.0 10.0.4.205 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
timeout floating-conn 0:00:00
dynamic-access-policy-record DfltAccessPolicy
http server enable
http 0.0.0.0 0.0.0.0 inside
http 0.0.0.0 0.0.0.0 management
http x.x.x.x x.x.x.x outside
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
crypto dynamic-map outside_dyn_map 20 set transform-set ESP-3DES-SHA
crypto map outside_map 65535 ipsec-isakmp dynamic outside_dyn_map
crypto map outside_map interface outside
crypto ca trustpoint _SmartCallHome_ServerCA
crl configure
crypto ca certificate chain _SmartCallHome_ServerCA
certificate ca 6ecc7aa5a7032009b8cebcf4e952d491
308205ec 308204d4 a0030201 0202106e cc7aa5a7 032009b8 cebcf4e9 52d49130
0d06092a 864886f7 0d010105 05003081 ca310b30 09060355 04061302 55533117
30150603 55040a13 0e566572 69536967 6e2c2049 6e632e31 1f301d06 0355040b
13165665 72695369 676e2054 72757374 204e6574 776f726b 313a3038 06035504
0b133128 63292032 30303620 56657269 5369676e 2c20496e 632e202d 20466f72
20617574 686f7269 7a656420 75736520 6f6e6c79 31453043 06035504 03133c56
65726953 69676e20 436c6173 73203320 5075626c 69632050 72696d61 72792043
65727469 66696361 74696f6e 20417574 686f7269 7479202d 20473530 1e170d31
30303230 38303030 3030305a 170d3230 30323037 32333539 35395a30 81b5310b
30090603 55040613 02555331 17301506 0355040a 130e5665 72695369 676e2c20
496e632e 311f301d 06035504 0b131656 65726953 69676e20 54727573 74204e65
74776f72 6b313b30 39060355 040b1332 5465726d 73206f66 20757365 20617420
68747470 733a2f2f 7777772e 76657269 7369676e 2e636f6d 2f727061 20286329
3130312f 302d0603 55040313 26566572 69536967 6e20436c 61737320 33205365
63757265 20536572 76657220 4341202d 20473330 82012230 0d06092a 864886f7
0d010101 05000382 010f0030 82010a02 82010100 b187841f c20c45f5 bcab2597
a7ada23e 9cbaf6c1 39b88bca c2ac56c6 e5bb658e 444f4dce 6fed094a d4af4e10
9c688b2e 957b899b 13cae234 34c1f35b f3497b62 83488174 d188786c 0253f9bc
7f432657 5833833b 330a17b0 d04e9124 ad867d64 12dc744a 34a11d0a ea961d0b
15fca34b 3bce6388 d0f82d0c 948610ca b69a3dca eb379c00 48358629 5078e845
63cd1941 4ff595ec 7b98d4c4 71b350be 28b38fa0 b9539cf5 ca2c23a9 fd1406e8
18b49ae8 3c6e81fd e4cd3536 b351d369 ec12ba56 6e6f9b57 c58b14e7 0ec79ced
4a546ac9 4dc5bf11 b1ae1c67 81cb4455 33997f24 9b3f5345 7f861af3 3cfa6d7f
81f5b84a d3f58537 1cb5a6d0 09e4187b 384efa0f 02030100 01a38201 df308201
db303406 082b0601 05050701 01042830 26302406 082b0601 05050730 01861868
7474703a 2f2f6f63 73702e76 65726973 69676e2e 636f6d30 12060355 1d130101
ff040830 060101ff 02010030 70060355 1d200469 30673065 060b6086 480186f8
45010717 03305630 2806082b 06010505 07020116 1c687474 70733a2f 2f777777
2e766572 69736967 6e2e636f 6d2f6370 73302a06 082b0601 05050702 02301e1a
1c687474 70733a2f 2f777777 2e766572 69736967 6e2e636f 6d2f7270 61303406
03551d1f 042d302b 3029a027 a0258623 68747470 3a2f2f63 726c2e76 65726973
69676e2e 636f6d2f 70636133 2d67352e 63726c30 0e060355 1d0f0101 ff040403
02010630 6d06082b 06010505 07010c04 61305fa1 5da05b30 59305730 55160969
6d616765 2f676966 3021301f 30070605 2b0e0302 1a04148f e5d31a86 ac8d8e6b
c3cf806a d448182c 7b192e30 25162368 7474703a 2f2f6c6f 676f2e76 65726973
69676e2e 636f6d2f 76736c6f 676f2e67 69663028 0603551d 11042130 1fa41d30
1b311930 17060355 04031310 56657269 5369676e 4d504b49 2d322d36 301d0603
551d0e04 1604140d 445c1653 44c1827e 1d20ab25 f40163d8 be79a530 1f060355
1d230418 30168014 7fd365a7 c2ddecbb f03009f3 4339fa02 af333133 300d0609
2a864886 f70d0101 05050003 82010100 0c8324ef ddc30cd9 589cfe36 b6eb8a80
4bd1a3f7 9df3cc53 ef829ea3 a1e697c1 589d756c e01d1b4c fad1c12d 05c0ea6e
b2227055 d9203340 3307c265 83fa8f43 379bea0e 9a6c70ee f69c803b d937f47a
6decd018 7d494aca 99c71928 a2bed877 24f78526 866d8705 404167d1 273aeddc
481d22cd 0b0b8bbc f4b17bfd b499a8e9 762ae11a 2d876e74 d388dd1e 22c6df16
b62b8214 0a945cf2 50ecafce ff62370d ad65d306 4153ed02 14c8b558 28a1ace0
5becb37f 954afb03 c8ad26db e6667812 4ad99f42 fbe198e6 42839b8f 8f6724e8
6119b5dd cdb50b26 058ec36e c4c875b8 46cfe218 065ea9ae a8819a47 16de0c28
6c2527b9 deb78458 c61f381e a4c4cb66
quit
crypto isakmp enable outside
crypto isakmp policy 10
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
telnet x.x.x.x 255.255.255.255 outside
telnet 0.0.0.0 0.0.0.0 inside
telnet 0.0.0.0 0.0.0.0 management
telnet timeout 5
ssh 0.0.0.0 0.0.0.0 inside
ssh 0.0.0.0 0.0.0.0 management
ssh timeout 5
console timeout 0
management-access inside
dhcpd address 192.168.1.2-192.168.1.254 management
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
enable outside
group-policy ppso internal
group-policy ppso attributes
dns-server value 10.0.4.241 10.0.4.14
split-tunnel-policy tunnelspecified
split-tunnel-network-list value splittunn-ppso
default-domain value ppso.local
split-dns value ppso.local
address-pools value vpn-pool
tunnel-group VPN type remote-access
tunnel-group VPN general-attributes
address-pool vpn-pool
default-group-policy VPN
tunnel-group VPN ipsec-attributes
pre-shared-key *
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum client auto
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
inspect ip-options
inspect icmp
service-policy global_policy global
prompt hostname context
call-home reporting anonymous
Cryptochecksum:88a9b69fc3d718c3badfa99db2c7ce4fYeah, I figured out where my problem was.
My IP Local Pool range was the problem.
I was using 10.10.10.0 which conflicted with a point-to-point connection where the serial interfaces were numbered and using 10.10.10.1 and 10.10.10.2.
Traffic would leave the firewall, hit the intended host, go back through my core router, then off to the other network.
I changed my ip local pool to a different range (192.168.100.0) and my problem was solved. -
Hi Guys
I configured a remote access vpn to our secondary office router (no failover or anything on configured)
I can login but i cannot access the internal lan.
I've attachted the config, if anyone has an idea please let me know.
RegardsNo, currently VPN is not supported on any of the Blackberry devices.
-
Remote access VPN with Cisco Router - Can not get the Internal Lan .
Dear Sir ,
I am doing Remote Access VPN through Cisco Router. Before the real deployment, I want to simulate it with GNS3.Need you help to complete the job .Please see the attachment for Scenario, Configuration and Ping status.
I am getting IP address when i connect through VPN client .But I can not ping to the internal lan -192.168.1.0.Need your help to sole the issue.
Below is the IP address of the device.
Local PC connect with Router -2 (Through MS Loopback) Router -2 Router-1 PC -01
IP Address :10.10.10.2 Mask : 255.255.255.0 F0/01
IP address:10.10.10.1
Mask:255.255.255.0 F0/0
IP Address :20.20.20.1
Mask :255.255.255.0
F0/1
IP address :192.168.1.3
Mask:255.255.255.0
F0/0
IP address :20.20.20.2
Mask :255.255.255.0
F0/1
IP address :192.168.1.1
Mask:255.255.255.0
I can ping from local PC to the network 10.10.10.0 and 20.20.20.0 .Please find the attach file for ping status .So connectivity is ok from my local PC to Remote Router 1 and 2.
Through Cisco remote vpn client, I can get connected with the VPN Router R1 (Please see the VPN Client pic.)But cannot ping the network 192.168.1.0
Need your help to fix the problem.
Router R2 Configuration :!
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname R2
boot-start-marker
boot-end-marker
no aaa new-model
memory-size iomem 5
no ip icmp rate-limit unreachable
ip cef
no ip domain lookup
ip auth-proxy max-nodata-conns 3
ip admission max-nodata-conns 3
ip tcp synwait-time 5
interface FastEthernet0/0
ip address 20.20.20.2 255.255.255.0
duplex auto
speed auto
interface FastEthernet0/1
ip address 10.10.10.1 255.255.255.0
duplex auto
speed auto
ip forward-protocol nd
no ip http server
no ip http secure-server
control-plane
line con 0
exec-timeout 0 0
privilege level 15
logging synchronous
line aux 0
exec-timeout 0 0
privilege level 15
logging synchronous
line vty 0 4
login
end
Router R1 Configuration :
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname R1
boot-start-marker
boot-end-marker
aaa new-model
aaa authentication login USERAUTH local
aaa authorization network NETAUTHORIZE local
aaa session-id common
memory-size iomem 5
no ip icmp rate-limit unreachable
ip cef
no ip domain lookup
ip auth-proxy max-nodata-conns 3
ip admission max-nodata-conns 3
username vpnuser password 0 strongpassword
ip tcp synwait-time 5
crypto keyring vpnclientskey
pre-shared-key address 0.0.0.0 0.0.0.0 key cisco123
crypto isakmp policy 10
encr 3des
hash md5
authentication pre-share
group 2
crypto isakmp client configuration group remotevpn
key cisco123
dns 192.168.1.2
wins 192.168.1.2
domain mycompany.com
pool vpnpool
acl VPN-ACL
crypto isakmp profile remoteclients
description remote access vpn clients
keyring vpnclientskey
match identity group remotevpn
client authentication list USERAUTH
isakmp authorization list NETAUTHORIZE
client configuration address respond
crypto ipsec transform-set TRSET esp-3des esp-md5-hmac
crypto dynamic-map DYNMAP 10
set transform-set TRSET
set isakmp-profile remoteclients
crypto map VPNMAP 10 ipsec-isakmp dynamic DYNMAP
interface FastEthernet0/0
ip address 20.20.20.1 255.255.255.0
ip nat outside
ip virtual-reassembly
duplex auto
speed auto
crypto map VPNMAP
interface FastEthernet0/1
ip address 192.168.1.1 255.255.255.0
ip nat inside
ip virtual-reassembly
duplex auto
speed auto
ip local pool vpnpool 192.168.50.1 192.168.50.10
ip forward-protocol nd
ip route 10.10.10.0 255.255.255.0 FastEthernet0/0
no ip http server
no ip http secure-server
ip nat inside source list NAT-ACL interface FastEthernet0/0 overload
ip access-list extended NAT-ACL
deny ip 192.168.1.0 0.0.0.255 192.168.50.0 0.0.0.255
permit ip 192.168.1.0 0.0.0.255 any
ip access-list extended VPN-ACL
permit ip 192.168.1.0 0.0.0.255 192.168.50.0 0.0.0.255
control-plane
line con 0
exec-timeout 0 0
privilege level 15
logging synchronous
line aux 0
exec-timeout 0 0
privilege level 15
logging synchronous
line vty 0 4
endDear All,
I am doing Remote Access VPN through Cisco Router. Before the real deployment, I want to simulate it with GNS3.Need you help to complete the job .
Please see the attachment for Scenario, Configuration and Ping status. I am getting IP address when i connect through VPN client .But I can not ping to the internal lan -192.168.1.0.Need your help to sole the issue.
Waiting for your responce .
--Milon -
Remote Access VPN, how to specify on which interface clients will be placed on?
Hi,
I have a general understanding problem with remote access VPN and Cisco ASA.
If I have an ASA with multiple interfaces and I want to make sure that a Remote Access VPN Client is placed onto a specific interface, how do I do this?
example:
ASA has 4 interfaces: outside, inside-clients, inside-workers, inside-lab.
I want to allow multiple Remote Access VPN configurations that put clients coming from "outside" to "inside-lab" and "inside-clients", with two different profiles and two different IP pools, as the IP addresses for each of the interfaces is different.
How do I do that?
If possible be as explanatory as possible for me to really grasp the concept.
Many thanks
PatHi,
The ASA will view the hosts in its routing table behind the ASA interface which forms the VPN connection with the VPN Client. This is most of the time the interface called "outside".
By default the ASA allows all traffic coming from a VPN connection to bypass the interface ACL of the ASA. The thought process behind this is I guess the fact that the VPN devices/clients have already proven they have right to connect to the network to all traffic is allowed.
The configuration that controls this setting globally on the ASA is
sysopt connection permit-vpn
The above is the default setting of the command and it WONT show up in the CLI format configurations because its a default setting.
If you were to issue the following command
no sysopt connection permit-vpn
Then this would mean that the ASA would require an ACL statement on its VPN terminating interface (outside) to permit the traffic from the VPN Pool to the LAN networks.
Naturally you would have to take into consideration also that if you have existing VPNs and insert the above global command they would also need ACL statements on the "outside" interface ACL or the inbound traffic from the VPN will start to get blocked.
Other option (wihtout touching the above setting) would be to configure VPN Filter ACL that is a separate ACL that is only attached to a certain user or group of users.
I personally prefer the method of using the above global setting and using the "outside" interface ACL to control traffic.
Naturally it still leaves the question of how you are going to configure the Tunnel Groups, Group Policys and Usernames. To be honest, I have gotten a bit distracted from VPN client setups and have forgotten a lot of stuff since I dont work with them on a day to day basis. I mostly handle L2L VPN nowadays among normal firewall configurations.
If I had to suggest something simple at this point it would be this
Configure separate Tunnel Groups
Configure separate VPN Pools for the above Tunnel Groups
Configure separate Group Policys for the above Tunnel Groups
Configure the above mentioned Global setting to limit inbound traffic from VPN
Configure the "outside" interface ACL so that you only permit traffic from a certain VPN Tunnel Group users only to certain LAN networks
Configure the required NAT0 configurations for traffic between these networks
As Marcin said, there are multiple different ways to achieve the same thing as above.
And as I said I have gotten a bit rusty with the VPN Client side on the ASA so I am not sure if at the moment I can even consider all the possible options but surely the simple ones.
PS. The link that Marcin posted seems to point to a Group Policy setting that would let you lock the that VPN connection to use only a certain local Vlan (subinterface) on the ASA and therefore limit traffic from going to networks behind other interfacec
Hope this helps
- Jouni -
How can I set up remote access on my iPad?
How can Iset up remote access on my iPad?
Thank you for responding, James. I just figured it out. I used Safari to connect to my office server system by using the http://mail server address/remote. It works just like any computer.
Maybe you are looking for
-
Error while running the CAT script
Hello, I am running eCATT script that creates test users by copying from source users to target users. I am getting following error message. Field USLOGOND-USTYP. input value is longer than screen field Message no. 00348 Diagnosis A screen field was
-
Hi, I want to know in which GL table i can get following information. GL Code Document No. Posting Date Entry Time Amount. Regards, Nilesh Surve. Moderator: Please, search before posting
-
Hello - After adding subtitles to a movie file (using Submerge), it will play fine in Quicktime, but once imported to and played in iTunes (10.7), the subtitles don't show up. This problem has started recently - I was previously able to play the subt
-
The title bar of all my windows is unreadable, with a weird vertical stripes!
I just upgraded my 10.7 machine to 10.7.5 (from 10.7.3 or 10.7.4, I don't remember; I used the standard auto-update). Now the title bar of all my windows is unreadable, with a weird vertical striped pattern, and the buttons in my finder window are a
-
I have searched the forum, but unable to find a step-by-step procedure that I can understand. I have imported my pix (Raw+Jpeg Pairs) both as masters. They both show as one project, but I cannot find out how to have each show as a separate project (a