Remote Provisioning for SPA 3102 and PAP 2 Series

Hi,
can some one help me with SETTING up Provisioning server for SPA 3102 pap2 etc using TFTP servers (I want a detailed explanation ) please it is urgent

These urls might help:
HTTPS Based Remote Provisioning with the SPA2102, SPA3102, and SPA9000:
http://www.cisco.com/en/US/products/ps10024/products_qanda_item09186a0080a33b6a.shtml
http://www.cisco.com/en/US/docs/voice_ip_comm/csbpvga/spa3102/release/notes/SPA3102_RN_V5-2.pdf

Similar Messages

SPA-3102 and Fax

Here's the problem: I am currently using a fax-switch that answers the incoming line, listens for a fax tone and, should it hear it, forwards the call to a fax machine. Without fax tone, the call is routed to the SPA-3102 and treated as voice.
This setup works nicely, but has one BIG disadvantage: All fax switches 'steal' the Caller ID. I am now trying to skip the fax-switch and use the SPA-3102 directly, by connecting the fax machine directly to the phone port of the unit. Since the SPA-3102 has the ability to recognize incoming faxes, is it able to route the call directly to the phone port? Without actually bothering the connected VOIP equipment?
I have tried to find a solution all over the Internet, but I seem to either be to blind to find anything, or, it might just not work. Thanks for your answers and suggestions.
Michaela

Thank you. I knew there must be a quick fix. Though ring thru would make the fax machine take all calls, which would make incoming phone calls be lost. If things were that easy, I wouldn't have bothered to ask. I was expecting somebody with actual Linksys knowledge to answer my question. Thanks again.

[svn] 1433: adding 'console' security constraint to MBeanServerGateway remote object for MBean tests and ds-console , used when running on Websphere with administrative security enabled.

Revision: 1433
Author: [email protected]
Date: 2008-04-28 13:13:12 -0700 (Mon, 28 Apr 2008)
Log Message:
adding 'console' security constraint to MBeanServerGateway remote object for MBean tests and ds-console, used when running on Websphere with administrative security enabled. Should call setCredentials("bob","bob1") to use this RO.
Modified Paths:
blazeds/branches/3.0.x/qa/apps/qa-regress/WEB-INF/flex/remoting-config.mods.xml
blazeds/branches/3.0.x/qa/apps/qa-regress/WEB-INF/flex/services-config.mods.xml

Hi,
It seems that you were using Hyper-V Remote Management Configuration Utility from the link
http://code.msdn.microsoft.com/HVRemote, if so, you can refer to the following link.
Configure Hyper-V Remote Management in seconds
http://blogs.technet.com/jhoward/archive/2008/11/14/configure-hyper-v-remote-management-in-seconds.aspx
By the way, if you want to perform the further research about Hyper-V Remote Management Configuration Utility, it is recommend that you to get further
support in the corresponding community so that you can get the most qualified pool of respondents. Thanks for your understanding.
For your convenience, I have list the related link as followed.
Discussions for Hyper-V Remote Management Configuration Utility
http://code.msdn.microsoft.com/HVRemote/Thread/List.aspx
Best Regards,
Vincent Hu

HT3180 Uploaded new software update and all I have is a little black box with an incessant flashing white light. I have pushed menu + downarrow on the remote, unplugged for 10 seconds and stiill no change when I plug it in again ! !

Uploaded new software update and all I have is a little black box with an incessant flashing white light. I have pushed menu + downarrow on the remote, unplugged for 10 seconds and stiill no change when I plug it in again ! !

Welcome to the Apple Community.
If your problem persists get yourself a micro USB cable (sold separately), you can restore your Apple TV from iTunes:
Remove ALL cables from Apple TV. (if you don't you will not see Apple TV in the iTunes Source list)
Connect the micro USB cable to the Apple TV and to your computer.
Reconnect the power cable (only for Apple TV 3)
Open iTunes.
Select your Apple TV in the Devices list, and then click Restore.
(You may already have a micro USB cable if you have a camera or other digital device)

Driver Intel USB 3.0 Driver for Intel 8 and U/Y Series doesn't work with a specific Kingston USB

Hello guys, just the other problem I'm facing with the 840 G2
I'm working in the MDT image for the HP 840 G2 and I would like to comment you one problem that I found with the USB 3.0 drivers. Based in your webpage, the last HP USB 3.0 official drivers are:
Intel USB 3.0 Driver for Intel 8 and U/Y Series Products
3.0.1.41 A from 15 dic 2014
I have found that those drivers doesn't work properly; if you insert a Kingston DTSE9 (32GB) the content of the usb will not be accessible randomly. The event viewer will display:
The driver detected a controller error on \device\harddisk1\DR13
To solve this problem you have to obtain the last version of the drivers from the Intel webpage:
https://downloadcenter.intel.com/download/22824/USB-3-0-Driver-Intel-USB-3-0-eXtensible-Host-Control...
I have all the drivers properly installed and it seems that the computer is working fine, however I'm a little worry thinking if I should update all the driver to avoid possible problem like this one.
If you have found similar problems it would be nice to share it.
Thank you very much.

Hi,
Please use the following post:
http://h30434.www3.hp.com/t5/forums/replypage/board-id/General/message-id/76373
Thanks.
BH
**Click the KUDOS thumb up on the left to say 'Thanks'**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

SPA-3102 and CallerID.

Hi all.
I have a trouble with CID(caller ID) forward from PSTN to VoIP.
I see CID in web UI, but in SIP Invite package CID seems like
CalledID.
How can I fix it?
In web I enable "PSTN CID For VoIP CID:" checkbox.

Thank you. I knew there must be a quick fix. Though ring thru would make the fax machine take all calls, which would make incoming phone calls be lost. If things were that easy, I wouldn't have bothered to ask. I was expecting somebody with actual Linksys knowledge to answer my question. Thanks again.

Upgraded the firmaware for SPA-3000 and lost the dial tone

Please help me figure out the problem with my Sipura box which has lost the dial tone after I upgraded the firmware. All the configuration looks fine. it is registering fine too but no dial tone.

Reset the device to factory default. This is usually needed after upgrading the firmware.

SIP phone and SPA 3102

Hi,
I don't have an ipPBX or call signaling server. Can I register a SIP phone on the remote SPA 3102 then call the remote number. SPA 3102 is on remote site, the FXO port is connected to a phone line. My SIP phone is on local site, connected to Internet.
Thanks

yytellmey wrote:
Hi,
Can I register a SIP phone on the remote SPA 3102 then call the remote number. SPA 3102 is on remote site, the FXO port is connected to a phone line. My SIP phone is on local site, connected to Internet.
Yes you can do that. You need to know the ip address where you are calling. This is called direct ip dialing. You can call the SPA3102 and have the attached phone ring, or you can call the SPA3102 and have it dial a call out the pstn line. It all depends on what you want to do.
Initially you can get it working with whatever ip address you have at the moment. For the long term, if you don't have a static ip address you can get a symbolic address from someone like dyndns.com and then when your ip address changes you setup some means, either thru your router that supports dynamic dns, or with a pc program to keep your ip address updated at dyndns for your symbolic address.
You almost always have to forward the sip signalling port in your router to the SPA3102. You may also have to forward the spa's rtp ports in your router to the SPA3102.
There are a couple of ways to configure the SPA3102 when you want to bridge the call out the pstn line. The simple way is to just return a dial tone to the caller and then the caller enters the pstn number they want to dial. A more complicated way is to send a sip invite to the SPA3102 and have the SPA dial the number. The latter method is more reliable because you don't have to send dtmf signals over your voip link.

High time SPA 3102 supports TLS and SDP

There have been absolutely no firmware updates in years for SPA 3102
Its a pity that SPA 3102 doesn't support TLS + SRTP with SDP (which is the default
and widely used key exchange mechanism as supposed to some proprietary method
or MIKEY that no one supports).
Grandstream has greatly overtaken with TLS +SRTP in their HT.503 that also sells much cheaper.
I have about 20 boxes of 3102 and can't throw them. I need to buy about 12 more and wish to
have uniformity. Main problem I see with 3102 is TLS and use of SDP for SRTP key exchange.
Otherwise is a great product.
Please have your engineering team make this a high priority and try to provide firmware update
for all the 3102 hw versions.
Thanks,
Anz

> does not have the support for SRTP.
This is contrary to what a lot of information out there says. Are you sure ?!
I would like to be able to use a gateway that can talk to a 3102 using SRTP and mini-certificate without using anothe 3102. There was a mention of this by your representative himself.
I am not really interested in your upcoming ATA that is similar to SPA 3102.
Are you going to replace all my SPA 3102 for free ?!!
Why can't you just do a firwmare upgrade for SPA 3102.
Please provide accurate and proper answers, that would be appreciated.

Connecting an SPA 3102 after the computer

I am moving to a house in a fairly remote part of Australia without a telephone connection. To get the phone connected will be very expensive and take considerable time. I have mobile phone and wireless internet connection available but only with the most expensive provider. I am not a big user of the phone but every now and then, I have to make one of those calls that go through adozen menus and then leave you on hold for an hour, theb type of call that can send you bankrupt using a mobile service.
My proposed solution is to have a prepaid wireless internet account, using a USB dongle connected to my computer as the internet connection. Then to connect either a SPA3102 or a PAP 2T between the computer and a handset and use a VOIP service such as Voipcheap to make calls. With this setup, I would have unlimited landline calls within Australia for around $50 per year, much less that something like Skype.
Can I do this and if so, how? I have both devices and they are both presently configured to work connected to my Linksys gateway. Do I connect the computer to the LAN or eithernet of the SPA 3102 and will it just require a normal LAN cable? How do I assign the various addresses required? Do I need any extra software for my computer?
John Adams

Hi John -- Thanks for participating in the Small Business Support Community. Please consider posting in the section dedicated to Australia/New Zealand here:
https://supportforums.cisco.com/community/netpro/small-business/international/australia_newzealand?view=discussions.
Thanks,
Stephanie Reaves
Cisco Small Business

Syslog not being sent by spa-3102

I can't seem to get any syslog to come out of my spa-3102. I've enabled syslog putting the ip address in both the syslog server and the debug server in the "System" tab. I set the debug level to 3. I have my system in a "double NAT" configuration: internet -- spa-3102 -- NAT router -- LAN (incl. syslogd) I don't know how the SPA chooses which interface to send its syslog UDP to. Since my syslog server is on my LAN, I assume that I have to specify my router's external IP (assigned by the SPA-3102), and then I configured my router to forward the packets to my LAN machine running syslogd. I reconfigured my linux syslogd to accept remote syslog and to log local0 and user. Kind of complex I know, and multiple points where it could be failing. But I want the SPA in front so it can do QOS and so I don't have to worry about NAT for its SIP support. Any suggestions on what I might do.

Just responding to myself -- it seems it was some problem with my particular syslog server, nothing to do with the SPA. I set up an alternative network syslog on a different LAN machine, and it is working fine through the double NAT and forwarding of UDP 514. -mda

SPA 3102: loosing connection intermittently

Hi,
I am using SPA 3102 and D-Link wireless router together. Connection is Cable Modem to SPA 3102 to D-Link DIR-615.
Both the phone and wirless works fine in this set up. The main issue is when I use utorrent, SPA 3102 keeps resetting (loosing connection intermittently). All the three lights goes of for a second and then comes back. End result is, I have to keep resetting the routers (power off for 10 secs and switch on). This is really annoying, I have to keep doing it atleast 3 or 4 times a day. I guess the problem might be with the heavy downloading/uploading with utorrent. Any way out ? Help appreciated.
aj

Ooops, sorry My first post was a mistake. Here is my question:
I have modem connection to a remote site.This connection must go from wire to Ethernet. The modems are 2-wire, not dial-up, and are embedded in a device, so there is no access to the serial port of the device.
I have two SPA3102. On the remote site the modem is always connected to the FXS port. This port is configured with SAS Enable=Yes and SAS Inbound RTP Sink = $IP. On the local site when modem is connected the conection is automatically established. With Wireshark I can see that RTP audio stream is flowing in both directions but signal can not be heared on the server side. What should I do to hear the inbound stream? Is it possible with SPA3102?
First I tried with SPA112 as SAS on remote site. The signal passes in both directions and can be heared on SPA112 port. Same settings. But SPA112 causes delay of 140ms and timing is critical for my devices. SPA3102 has only 80ms delay with RTP Packet Size = 0.02 and modems work with two SPA3102 configured as hot line. The problem with hot line is that in case of connection fail I have to go to the remote site to disconnect the modem and connect it again. Not very convinient.
Thanks
Svilen

Why logical partition is a must for voting disk and OCR

Hi Guys,
I just started handling jobs for RAC installation, I have a simple question regarding the setup.
Why does logical partition have to be used for voting disk and OCR?
I tried partition the disk that were provisioned for voting disk and OCR with primary partition but when OUI is trying to recognize the disk, it cannot find the disk that has been partitioned with primary partition.
Thank you,
Adhika

Hello Adhika,
I found it on this doc http://download.oracle.com/docs/cd/B28359_01/install.111/b28250/storage.htm
Be aware of the following restrictions for partitions:
* You cannot use primary partitions for storing Oracle Clusterware files while running the OUI to install Oracle Clusterware as described in Chapter 5, "Installing Oracle Clusterware". You must create logical drives inside extended partitions for the disks to be used by Oracle Clusterware files and Oracle ASM.
* With 32-bit Windows, you cannot create more than four primary disk partitions for each disk. One of the primary partitions can be an extend partition, which can then be subdivided into multiple logical partitions.
* You can assign mount points only to primary partitions and logical drives.
* You must create logical drives inside extended partitions for the disks to be used by Oracle Clusterware files and Oracle ASM.
* Oracle recommends that you limit the number of partitions you create on a single disk to prevent disk contention. Therefore, you may prefer to use extended partitions rather than primary partitions.
For these reasons, you might prefer to use extended partitions for storing Oracle software files and not primary partitions.
All the best,
Rodrigo Mufalani
http://www.mrdba.com.br/mufalani

LiveLinkException [HR#10049]: User is not provisioned for this operation

Hi,
I installed EAL 11.1.1.4.000 on win2008 R2 64bit Japanese OS.
But I met an issue after successful added Analytics Link Server node.
When Adding bridge components to an Analytics Link Server, the error message said as:
"Financial Management Server cannot be added: User is not provisioned for this operation"
and the EAL.log shows:
"LiveLinkException [HR#10049]: User is not provisioned for this operation"
Does it means I did the wrong setting when configure EAL?
Thanks

Have you set up the correct provisioning for the user in Shared Services?
Cheers
John
http://john-goodwin.blogspot.com/

SPA-3102 Line is disconnecting every 10 minutes and 40 sec

Hi,
I've a SPA-3102 connected behind a Motorola router, for any reason I'm not able to find, each time you call someone, after 10 min and 40 sec, the line cuts, and you have to call back.
Software Version: 3.3.6(GW) Hardware Version: 1.4.5(a)
SPA-3102 has a fix IP, and config has been done by my phone IP provider, does anyone have an idea which settings needs to be modified to avoid this cut?
Thanks for your help

I think under the “Regional” tab, you will have “Control Timer Values” and I belive thios is where you have to adjest the timer. I am not quite sure as well what parameters are needed to tweek in this section but I am sure that it should be one of them. Maybe try adjusting the “Reorder delay”. I suggest contacting Cisco Tech support to further look into your concern. I believe this unit belongs to the business series devices that Cisco is now supporting. Try to go to this link for the other business series devices and the site where you can get hold of Cisco for support:
http://www.cisco.com/web/products/linksys/index.html

Remote Provisioning for SPA 3102 and PAP 2 Series

Similar Messages

Maybe you are looking for