Remote VPN drop

Hi, ..
There are Multiple Remote access connections comes to my VPN Concentrator.
each remote office whos connected to my VPN can just connect with ONE PC only.
when he tries to use VPN software to create new connection he success BUT the first drop.
the solution was to Create Microsoft VPN Connection so that more than one person can connect from each office.
I need to let them connect using Cisco VPN Software NOT microsoft.

Hello,
Could you use the firewall/router connecting your remote sites to the internet to setup a LAN-to-LAN VPN?
In case this is not possible, did the clients configure "Enable Transparent tunneling" with IPSec over UDP? It somehow sounds like a NAT/PAT problem in conjunction with "VPN passthrough" on lower end DSL/cable routers. They might only support one IPSec tunnel at a time.
The transparent tunneling can be configured in the client through "Connection entries -> Modify" and then a new window pops up where you can select the "transport" tab and enable transparent tunneling with UDP.
Hope this helps! Please rate all posts.
Regards, Martin

Similar Messages

Users VPN drops after every 5 mins

Hi everyone,
We have user whose remote VPN drops after every 5 mins.
Need to know whats things i can check to troubleshoot the issue?
User connects by RSA Token.
ISP connection is ok its not issue.
Any thing i can check in ASA ?
Thanks
Mahesh

On the client side, have you tested wired vs wireless to see if the problems exists in both? If it's only one of them but not the other, try updating the drivers. Also, if it's windows 7, take a look at the power settings in control panel. I've seen where agressive power settings will shut off the network port when idle. Not that big of a deal in a LAN environment but it wreaks havoc on VPN.

Traffic not returning to remote VPN connections

I've successfully setup remote VPN connections to my ASA using vpnc as the client and everything behaves as expected. I'm trying to test the official Cisco client and I'm unable to make the same SSH connections across the VPN as I was using vpnc.
The ASA shows connections the IKE and IPSec connections forming, and shows connections being built for the SSH traffic across the VPN.
tcpdump shows the host listening on SSH behind the ASA receiving the traffic and sending ACKs in reply. They don't appear to be arriving back
at the remote client though, and SSH connections timeout without connecting.
Any idea what might be stopping the return traffic? I thought it might be some policy the ASA is pushing out to the Cisco client but not to vpnc but I can't spot anything obvious.

Is the internal SSH host you are connecting to sending ACKS (as you've stated), or SYN/ACKs?
It might be nice to know if the TCP three way handshake is being completed, and subsequent packets are the issue, or if it's the initial TCP setup that is the issue.
Perhaps there would be some benefit in confirming whether these packets are making it through the IPSec tunnel, though the ASA un-encapsulated, or not through the ASA at all.
You could use Wireshark to look for un-encapsulated packets exiting the ASA.
You could use Wireshark to capture the "pre-encapsulated" traffic being sent to the far side, and the "post-decapsulation" traffic returning from the far side, by capturing on the Cisco VPN Client virtual interface (Windows installation).
Perhaps examine IPSec SA details on the ASA and look for errors.
Perhaps logging on the internal interface ACL (log any packets denied) to identify whether the returning packets are being dropped.

Routing issue for remote vpn user and spoke

Hi all,
i have configure VPN (see attached file)
before upgrading ASA from 8.3 to 8.4, SPOKES was able to communicate between them and also remote VPN users was able to access spoke site.
after upgrade ASA HUB, neither spoke-to-spoke nor remoteuser---to---spoke cannot communicate
here is NAT exemption configuration on ASA HUB. only this ASA have been upgrade. nothing have been done on other site
object network 172.17.8.0
subnet 172.17.8.0 255.255.255.0
object network 10.100.96.0
subnet 10.100.96.0 255.255.240.0
object network VPN-SUBNET
subnet 172.20.1.0 255.255.255.0
nat (outside,outside) source static 172.17.8.0 172.17.8.0 destination static 10.100.96.0 10.100.96.0
nat (outside,outside) source static 10.100.96.0 10.100.96.0 destination static 172.17.8.0 172.17.8.0
nat (outside,outside) source static VPN-SUBNET VPN-SUBNET destination static 10.100.96.0 10.100.96.0
nat (outside,outside) source static VPN-SUBNET VPN-SUBNET destination static 172.17.8.0 172.17.8.0
same-security traffic permit intra-interface
same-security traffic permit inter-interface
Please do you know what can be the problem ?
thanks so much for your help

Since you are not NATing any of those traffic and it's a u-turn traffic, pls remove those 4 NAT statements. They are not required at all.
Pls "clear xlate" after removing it and let us know how it goes.

Cisco Asa 5505 and Layer 3 Switch With Remote VPN Access

i got today a new CISCO LAYER 3 Switch .. so here is my scenrio
Cisco Asa 5505
I
Outside == 155.155.155.x
Inside = 192.168.7.1
VPN POOL Address = 10.10.10.1 - 10.10.10.20
Layer 3 Switch Config
Vlan 2
interface ip address = 192.168.1.1
Vlan 2
interface ip address = 192.168.2.1
Vlan 2
interface ip address = 192.168.3.1
Vlan 2
interface ip address = 192.168.4.1
Vlan 2
interface ip address = 192.168.5.1
ip Routing
So i want My Remote Access VPN clients to access all this Networks. So Please can you give me a helpfull trick or Link to configure the rest of my routing
Thank You all

When My Remote VPN is Connected , it reaches 192.168.7.2 of the Layer 3 VLan that's Connected to The ASA 5505 ,
But i can't reach the rest of the VLAN - example
192.168.1.1
192.168.1.2
192.168.1.3
192.168.1.4
192.168.1.5
But i can reach the Connected Interface Vlan to My ASA ..
So here i think iam miss configuration to my Route
Any Help Please this is urgent

Dual Remote VPN Connection

Hello Guys
i created three different Remote VPN connections with three different networks . i can make them one but for some reasons i don't mix all.
and iam using Cisco asa 5505 with Shrew Soft VPN software , so my problem is
- i connected Shrew soft remote vpn , if i try to connected another remote vpn connection this will not accept the second connection , so please can any one give me a remote vpn connection software that accepts more than one connection

Hi,
Since you mention the ASA and the VPN I presume you are trying to connect by VPN Client to the same ASA?
Why would you want to have several VPN client connections at the same time? (Though I think that isnt even possible)
What are you trying to accomplish by these 3 different VPN Client configurations configured on the same ASA?
Isnt it just possible to configure one VPN Client connection to the ASA that would handle all the traffic of these 3 VPN Client connections?
- Jouni

Asa 5505 Remote VPN Can't access with my local network

Hello Guys ,, i have a problem with my asa 5505 Remote VPN Connection with local network access , the VPn is working fine and connected , but the problem is i can't reach my inside network connection of 192.168.30.x , here is my configuration , please can you help me
ASA Version 8.2(1)
interface Vlan1
nameif inside
security-level 100
ip address 192.168.30.1 255.255.255.0
interface Vlan2
nameif outside
security-level 0
ip address 155.155.155.10 255.255.255.0
interface Vlan5
no nameif
no security-level
no ip address
interface Ethernet0/0
switchport access vlan 2
interface Ethernet0/1
interface Ethernet0/2
interface Ethernet0/3
interface Ethernet0/4
interface Ethernet0/5
interface Ethernet0/6
interface Ethernet0/7
ftp mode passive
access-list inside_nat0_outbound extended permit ip any 192.168.100.0 255.255.255.240
pager lines 24
logging asdm informational
mtu inside 1500
mtu outside 1500
ip local pool vpn-Pool 192.168.100.1-192.168.100.10 mask 255.255.255.0
icmp unreachable rate-limit 1 burst-size 1
no asdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 0 access-list inside_nat0_outbound
nat (inside) 1 0.0.0.0 0.0.0.0
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 icmp 0:00:02
timeout sunrpc 0:10:00 h323 0:05:00 h225 1:00:00 mgcp 0:05:00 mgcp-pat 0:05:00
timeout sip 0:30:00 sip_media 0:02:00 sip-invite 0:03:00 sip-disconnect 0:02:00
timeout sip-provisional-media 0:02:00 uauth 0:05:00 absolute
timeout tcp-proxy-reassembly 0:01:00
dynamic-access-policy-record DfltAccessPolicy
no snmp-server location
no snmp-server contact
snmp-server enable traps snmp authentication linkup linkdown coldstart
crypto ipsec transform-set ESP-3DES-SHA esp-3des esp-sha-hmac
crypto ipsec transform-set ESP-AES-256-MD5 esp-aes-256 esp-md5-hmac
crypto ipsec transform-set ESP-DES-SHA esp-des esp-sha-hmac
crypto ipsec transform-set ESP-DES-MD5 esp-des esp-md5-hmac
crypto ipsec transform-set ESP-AES-192-MD5 esp-aes-192 esp-md5-hmac
crypto ipsec transform-set ESP-3DES-MD5 esp-3des esp-md5-hmac
crypto ipsec transform-set ESP-AES-256-SHA esp-aes-256 esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-SHA esp-aes esp-sha-hmac
crypto ipsec transform-set ESP-AES-192-SHA esp-aes-192 esp-sha-hmac
crypto ipsec transform-set ESP-AES-128-MD5 esp-aes esp-md5-hmac
crypto ipsec security-association lifetime seconds 28800
crypto ipsec security-association lifetime kilobytes 4608000
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set pfs group1
crypto dynamic-map SYSTEM_DEFAULT_CRYPTO_MAP 65535 set transform-set ESP-AES-128-SHA ESP-AES-128-MD5 ESP-AES-192-SHA ESP-AES-192-MD5 ESP-AES-256-SHA ESP-AES-256-MD5 ESP-3DES-SHA ESP-3DES-MD5 ESP-DES-SHA ESP-DES-MD5
crypto map outside_map 65535 ipsec-isakmp dynamic SYSTEM_DEFAULT_CRYPTO_MAP
crypto map outside_map interface outside
crypto isakmp enable outside
crypto isakmp policy 10
authentication pre-share
encryption 3des
hash sha
group 2
lifetime 86400
telnet timeout 5
ssh timeout 5
console timeout 0
dhcpd auto_config outside
threat-detection basic-threat
threat-detection statistics access-list
no threat-detection statistics tcp-intercept
webvpn
group-policy mull internal
group-policy mull attributes
vpn-tunnel-protocol IPSec
username xxx password eKJj9owsQwAIk6Cw encrypted privilege 0
vpn-group-policy Mull
tunnel-group mull type remote-access
tunnel-group mull general-attributes
address-pool vpn-Pool
default-group-policy mull
tunnel-group mull ipsec-attributes
pre-shared-key *
class-map inspection_default
match default-inspection-traffic
policy-map type inspect dns preset_dns_map
parameters
message-length maximum 512
policy-map global_policy
class inspection_default
inspect dns preset_dns_map
inspect ftp
inspect h323 h225
inspect h323 ras
inspect rsh
inspect rtsp
inspect esmtp
inspect sqlnet
inspect skinny
inspect sunrpc
inspect xdmcp
inspect sip
inspect netbios
inspect tftp
service-policy global_policy global
prompt hostname context

Hey Jennifer i did every thing you mention it , but still i can't reach my inside network (LOCAL network) iam using Shrew Soft VPN Access Manager for my vpn connection
here is my cry ipsec sa
interface: outside
    Crypto map tag: SYSTEM_DEFAULT_CRYPTO_MAP, seq num: 65535, local addr: 155.155.155.1
      local ident (addr/mask/prot/port): (0.0.0.0/0.0.0.0/0/0)
      remote ident (addr/mask/prot/port): (192.168.100.1/255.255.255.255/0/0)
      current_peer:155.155.155.1, username: Thomas
      dynamic allocated peer ip: 192.168.100.1
      #pkts encaps: 0, #pkts encrypt: 0, #pkts digest: 0
      #pkts decaps: 0, #pkts decrypt: 0, #pkts verify: 0
      #pkts compressed: 0, #pkts decompressed: 0
      #pkts not compressed: 0, #pkts comp failed: 0, #pkts decomp failed: 0
      #pre-frag successes: 0, #pre-frag failures: 0, #fragments created: 0
      #PMTUs sent: 0, #PMTUs rcvd: 0, #decapsulated frgs needing reassembly: 0
      #send errors: 0, #recv errors: 0
      local crypto endpt.: 155.155.155.1/4500, remote crypto endpt.: 155.155.155.20/4500
      path mtu 1500, ipsec overhead 82, media mtu 1500
      current outbound spi: 73FFAB96
    inbound esp sas:
      spi: 0x1B5FFBF1 (459275249)
         transform: esp-aes esp-sha-hmac no compression
         in use settings ={RA, Tunnel, NAT-T-Encaps, }
         slot: 0, conn_id: 12288, crypto-map: SYSTEM_DEFAULT_CRYPTO_MAP
         sa timing: remaining key lifetime (sec): 2894
         IV size: 16 bytes
         replay detection support: Y
         Anti replay bitmap:
          0x00000000 0x00000001
    outbound esp sas:
      spi: 0x73FFAB96 (1946135446)
         transform: esp-aes esp-sha-hmac no compression
         in use settings ={RA, Tunnel, NAT-T-Encaps, }
         slot: 0, conn_id: 12288, crypto-map: SYSTEM_DEFAULT_CRYPTO_MAP
         sa timing: remaining key lifetime (sec): 2873
         IV size: 16 bytes
         replay detection support: Y
         Anti replay bitmap:
          0x00000000 0x00000001

ASA 5505 remote vpn - not receiving packets from ASA

I am having problem configuring remote vpn between ASA5505 and Cisco VPN client v5. I can successfully establish connection between ASA and Vpn client and receive IP address from ASA. VPN client statistics windows shows that packets are send and encrypted but none of the packets is Received/Decrypted. Any ideas on what I have missed?
Thanks in advance for any help,M

crypto isakmp nat-traversal
Please rate helpful posts.

Remote VPN ! site-to-site

Remoe VPN client cannot get across L2L (site-to-site) tunnel after making connection.
Topology:
[remote]->[ASA1]-><L2L}->[ASA2]->LAN2
The problem is at the remote client, which is using Cisco VPN client.
Remote client connection is made fine to [ASA1].
Problem is that remote client does not know route to network LAN2 and dumps traffic off to its default gateway rather than directing it to [ASA1] for forwarding to [ASA2]. ([ASA1] and [ASA2], of course, know about each other.)
Cisco VPN client has capability of being "told" subsequent routes (Status->statistics->Route details).
As I see it, the client must get this info from the ASA to which it makes its remote VPN connection.
The advice I am hoping for is the CLI or ASDM syntax I need to apply to get the ASA to provide this route information.
TIA

Adam, thank you for the comprehensive reply ... unfortunately it's not working.
1. The statements you list above were already there to facilitate the L2L.
2. I turned-off split tunneling (or think I did) and ran a test ... no joy.
This took me back to my original premise that the remote client doesn't know how to send the traffic (bound for L2L) down the remote tunnel and dumps it of to its default gateway (to the WWW).
If you're willing to look at it, I have attached screen shots of the client ipconfig and the Cisco VPN client - showing its routes.
The ipconfig seems to say that the remote connection has its default gateway, and the tunnel has none.
The VPN client screen shows it knows a route (192.168.5.0/24) to the ASA, but nothing beyond. The ASA does, in fact, know about the network (10.64.0.0/16) at the other end of the L2L.
As I see it, if I can find a way to get the ASA to advertise this route to the VPN client, the problem might be solved. The client will then know to forward the traffic to the ASA instead of dumping it to the default gateway.
TIA

PIX 501 config - access to internal network not working from remote VPN users - everything on the inside is OK

One other thing - I had a problem with the key pairing so I rebuilt the rsa 1024 and the unit started working. Unfortunately I reloaded without the config in place and now I cannot get it to work again. Any help will be greatly apprecaited although I did review a dozen other posts of people having similar problems and for some reason there is never any conclusion as to the solution and I am not sure why.
Some other info from the client end:
I just ran the stats on the client and packets are being encrypted BUT none are decrypted.
Also Tunnel received 0 and sent 115119
Encryption is 168-bit 3-DES
Authentication is HMAC-SHA1
also even though the allow LAN is selected in the Cisco VPN client it states the local LAN is disabled in the client stats
also Transparent tunneling is selcted but in the stats it states it is inactive
I am connecting with the Cisco VPN Client Ver 5.0.07.0440
This config works. It is on the internal net 192.168..40.x and all users obtain dhcp and surf the web. It has required ports opened.The problem is that you can connect remotely via the VPN and you receive an IP address from the remote-vpn pool but you cannot see any machines on the internal network. The pix is at 40.2 and you cannot ping the pix and the pix from the remote PC connecting via the VPN and youcannot ping the remote PC from the PIX console when the remote is connected and receives the first IP address in the VPN pool of 192.168.40.25
I need to see the internal network and map network drives. I have another friend that is running the same config and it works but his computer is on a linksys wireless and has an IP of 192.168.1.x and the IP he receives from the VPN pool is 192.168.1.25 so I do not know if the same network is allowing this config to work even if there is an error in the config. In my present case I obtain the ip of 192.168.40.25 from the VPN pool and my connecting pc on 192.168.1.x I really am not sure how the VPN virtual adapter works. I am assuming it routes all traffic from your connecting PC to and from the virtual adapater but I really do not know for sure.
Other people have had similar issues with accessing the internal network from the VPN. One solution was the split-tunnel, another was the natting and another had to do with the encrption where there and an issue with the encrypt and ecrypt which was stopping the communicaton via the VPN.
I still cannot seem to find the issue with this config and any help will be greatly appreciated.
This is the config
interface ethernet0 100full
interface ethernet1 100full
nameif ethernet0 outside security0
nameif ethernet1 inside security100
enable password somepassword
hostname hostname
fixup protocol dns maximum-length 512
fixup protocol ftp 21
fixup protocol h323 h225 1720
fixup protocol h323 ras 1718-1719
fixup protocol http 80
fixup protocol rsh 514
fixup protocol rtsp 554
fixup protocol sip 5060
fixup protocol sip udp 5060
fixup protocol skinny 2000
fixup protocol smtp 25
fixup protocol sqlnet 1521
fixup protocol tftp 69
names
object-group network internal_trusted_net
network-object 192.168.40.0 255.255.255.0
object-group icmp-type icmp_outside
icmp-object echo-reply
icmp-object unreachable
icmp-object time-exceeded
icmp-object source-quench
access-list OutToIn permit icmp any xxx.xxx.xxx.0 255.255.255.248 object-group icmp_outside
access-list no_nat_inside permit ip 192.168.40.0 255.255.255.0 192.168.40.0 255.255.255.0
access-list split_tunnel permit ip 192.168.40.0 255.255.255.0 192.168.40.0 255.255.255.0
access-list OutToIn permit ip any any
access-list outbound permit ip any any
(NOTE: I had many more entries in the access list but removed them. Even with the above two allowing everything it does not work)
pager lines 24
mtu outside 1500
mtu inside 1500
ip address outside xxx.xxx.xxx.xxx 255.255.255.248
ip address inside 192.168.40.2 255.255.255.0
ip audit info action alarm
ip audit attack action alarm
ip local pool vpn_client_pool 192.168.40.25-192.168.40.30
pdm history enable
arp timeout 14400
global (outside) 1 interface
I had this statement missing from the previous posted config but even with the nat (inside) 0 access-list no_nat_inside it still does not work.
nat (inside) 0 access-list no_nat_inside
nat (inside) 1 0.0.0.0 0.0.0.0 0 0
access-group acl_outside_in in interface outside
access-group outbound in interface inside
route outside 0.0.0.0 0.0.0.0 xxx.xxx.xxx.xxx 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 rpc 0:10:00 h225 1:00:00
timeout h323 0:05:00 mgcp 0:05:00 sip 0:30:00 sip_media 0:02:00
timeout uauth 0:05:00 absolute
aaa-server TACACS+ protocol tacacs+
aaa-server RADIUS protocol radius
aaa-server LOCAL protocol local
http server enable
http 192.168.40.0 255.255.255.0 inside
no snmp-server location
no snmp-server contact
snmp-server community $XXXXXX$
no snmp-server enable traps
floodguard enable
sysopt connection permit-ipsec
crypto ipsec transform-set 3des_strong esp-3des esp-sha-hmac
crypto dynamic-map clientmap 50 set transform-set 3des_strong
crypto map vpn 50 ipsec-isakmp dynamic clientmap
crypto map vpn client configuration address initiate
crypto map vpn client configuration address respond
crypto map vpn client authentication LOCAL
crypto map vpn interface outside
isakmp enable outside
isakmp identity address
isakmp client configuration address-pool local vpn_client_pool outside
isakmp nat-traversal 20
isakmp policy 10 authentication pre-share
isakmp policy 10 encryption 3des
isakmp policy 10 hash sha
isakmp policy 10 group 2
isakmp policy 10 lifetime 86400
vpngroup remote-vpn split-tunnel split_tunnel
vpngroup remote-vpn idle-time 10800
vpngroup remote-vpn password ANOTHER PASSWORD
telnet timeout 5
ssh 0.0.0.0 0.0.0.0 outside
ssh 192.168.40.0 255.255.255.0 inside
ssh timeout 30
console timeout 60
dhcpd address 192.168.40.100-192.168.40.131 inside
dhcpd dns xxx.xxx.xxx.xxx xxx.xxx.xxx.xxx
dhcpd lease 3600
dhcpd ping_timeout 750
dhcpd enable inside
username AUSER password PASSWORD privilege 15
terminal width 80
****************** End of config
I have been searching docs and other people's postings trying to obtain the info to make this work. It appears pretty much boiler plate but I believe my problem is in the natting. I am using a range in the internal network for the VPN pool and I have tried switching this to other networks but this has not helped. Unfortunately I have been unable to get the PDM to work and I believe this is a PC config thing and I did not want to waste the time on it. I read a post where a person using the PDM interface with the same problem (not being able to access the internal network) was able to go to a section in the VPN wizard and set the Address Exeption Translation. They said they originally set the VPN subnet when they did not have to. Many of the other blogs I read also stated that if the natting is not proper for the VPN pool- that it will not work but I am confused by the examples. They show as I do the complete range for an access-list called no_nat_inside but I believe it should only have the VPN pool IP range and not the entire network since the others do require natting - not sure if my thought process is correct here. Any help will be greatly apprecaited. Also this morning I just tried a boiler plate example from CISCO and it also did not do what I need for it to do. And I also connect a PC to obtain an IP to see if I can see it - no good. The PC can ping the PIX and viceversa but no one can ping the remote PC that connects via the CISCO Remote VPN client even though it receive an address from the vpnpool. Also include LAN is checked off on the client. This was mentioned in anther post.
Thank you once again.

Hi,
PIX501 is a very very old Cisco firewall that has not been sold for a long time to my understanding. It also doesnt support even close to new software levels.
If you wanted to replace the PIX501 the corresponding model nowadays would be ASA5505 which is the smallest Cisco ASA firewall with 8 switch port module. There is already a new ASA5500-X Series (while ASA5505 is of the original ASA 5500 Series) but they have not yet introduced a replacing model for this model nor have they stopped selling this unit. I have a couple of them at home. Though naturally they are more expensive than your usual consumer firewalls.
But if you wanted to replace your PIX firewall then I would probably suggest ASA5505. Naturally you could get some other models too but the cost naturally rises even more. I am not sure at what price these are sold as used.
I used some PIX501 firewalls at the start of my career but have not used them in ages since ASA5505 is pretty much the firewall model we use when we need a firewall/vpn device for a smaller network/branch site.
Here is a PDF of the original ASA5500 Series.
http://www.cisco.com/en/US/prod/collateral/vpndevc/ps6032/ps6094/ps6120/prod_brochure0900aecd80285492.pdf
Here is a PDF of the new ASA5500-X Series
http://www.cisco.com/en/US/prod/collateral/vpndevc/ps6032/ps6094/ps6120/at_a_glance_c45-701635.pdf
I am afraid that its very hard for me atleast to troubleshoot this especially since I have not seen any outputs yet. Also the very old CLI and lack of GUI (?) make it harder to see what the problem is.
Could you provide the requested outputs?
From the PIX after connection test
show crypto ipsec sa
Screen captures of the VPN Client routing and statistics sections.
- Jouni

How to set two DNS domain in one Remote VPN group policy

Hello experts
I am using ASA 8.2 to provide IPsec remote VPN for our staff. And in the group policy I set default domain name which is needed for our DNS server to resolve internal URLs. But the problem is now we have two domain names on our DNS server, and host names in two domains are differents. So if I setup one domain name in the group policy, URLs in the other domain cannot be resolved when using VPN. But ADSM seems doesn't allow me to setup two domain names for the attribute 'Default Domain'. What can I do?
Thanks a lot.

Come on Experts, please help. Any way to achieve that, or it's a mission impossible.

AAA Radius Authentication for Remote VPN With ACS Server Across L2L VPN

Hi,
I have an ASA running fine on the network which provide L2L tunnel to remote site and provide Remote VPN for remote access users.
Currently, there is a need for the users to authenticate against an ACS server that located across the L2L VPN tunnel.
The topology is just simple with 2 interfaces on the ASA, inside and outside, and a default route pointing to the ISP IP Address.
I can ping the IP address of the ACS Server (which located at the remote site, IP addr: 10.10.10.56) from the ASA:
ping inside 10.10.10.56
However when I configure the ASA for the AAA group with commands:
aaa-server ACSAuth protocol radius
aaa-server ACSAuth host (inside) 10.10.10.56 key AcsSecret123
Then when I do the show run, here is the result:
aaa-server ACSAuth protocol radius
aaa-server host 10.10.10.56
key AcsSecret123
From what I thought is, with this running config, traffic is not directed to the L2L VPN tunnel
(seems to be directed to the default gateway due to the default route information) which cause failure to do the AAA authentication.
Does anybody ever implement such this thing and whether is it possible? And if yes, how should be the config?
Your help will be really appreciated!
Thanks.
Best Regards,
Jo

AAA is designed to enable you to dynamically configure the type of authentication and authorization you want on a per-line (per-user) or per-service (for example, IP, IPX, or VPDN) basis. You define the type of authentication and authorization you want by creating method lists, then applying those method lists to specific services or interfaces.
http://www.cisco.com/en/US/docs/ios/12_4/secure/configuration/guide/schaaa.html

2 tier security for remote vpn ?

Hi,
I have a cisco PIX 501 in which remote VPN is configured for our company. Currently, for the remote users, the authentication is just a vpn groupname and a password. All the users use the same credentials for logging in. Can I have separate remote vpn users using their own login crentials with a single vpngroup?

You can achive this via the x-auth feature, please check out the following links:
PIX 6.x:
http://www.cisco.com/en/US/products/hw/vpndevc/ps2030/products_tech_note09186a008010a206.shtml
7.x and later
http://www.cisco.com/en/US/products/ps6120/products_configuration_example09186a008060f25c.shtml
Regards
Farrukh

Help with setting up Remote VPN

Hi,
Currently our company is using following:
Linksys WAG200G(54Mbps): ADSL Modem/DHCP/Firewall/port forwarding/wireless
CISCO ESW-540-8P switch for intranet: 1x Windows Server 2012 Standard/ 1x NAS and connected to 1x CISCO WAP4410N for wireless
We intend to enable our network for remote VPN( 1 to 5 users) and as well as upgrading the WAG200G to new equipment to use 802.11n wireless.
Would hope someone can suggest stable small business equipment/s for our upgrade? I have previously bought the WAP4410N and tried upgrading to 802.11n for all our users but was not successful as this unit constantly give us access problems. So right I am only using this for my support purpose. I read the WAP321 is a stable equipment from community comments so may consider getting one for 802.11n access. As for VPN and ADSL modem, hope someone can suggest suitable stable models.
Thank you.

There are many devices that can provide you a VPN solution. Personally I would get a router of some sorts maybe a 2800 or 1800 series and then create a L2 tunnel config on it. There are many links on the web where you could almost do a copy paste of the config. The issue will then be the ability to do a NAT to the router and setting up internal access. That is always unique to the environment so I couldn't help more there without a better diagram and basic configs.
Here is a link with sample configs
http://tekcert.com/blog/2006/12/14/configuring-cisco-router-accept-vpn-connections
-Toby
Sent from Cisco Technical Support Android App

6.3.5 upgrade to 7.2.2 cant connect over remote VPN client

The device is a PIX 525 UR with v. 7.2.2 installed over 6.3.5. I have deleted all previous VPN setups and re-installed the remote vpn and client software multiple times and the VPN times out during securing the channel and comes back with a error: 412 the local client has disconnected the session. I have been using the ASDM VPN wizard to configure the VPN and upon submitting the config I recieve a warning saying the tunnel-group does not exist but then when I exit it shows up in the tunnel group and is listed in the CLI. Also in the debug logs iget the error: 3713902 Group = Eisenhower, IP = 166.214.197.X, Removing peer from peer table failed, no match!
I would appreicate any assisance with this attached is the relevent configuration.
Thanks,
Scott r

This document describes how to use the Cisco Adaptive Security Device Manager (ASDM) to configure authentication and authorization server groups on the Cisco PIX 500 Series Security Appliance. In this example, the server groups created are used by the policy of a VPN tunnel group to authenticate and authorize incoming users.
http://www.cisco.com/en/US/products/hw/vpndevc/ps2030/products_configuration_example09186a008060f261.shtml

Remote VPN drop

Similar Messages

Maybe you are looking for