Remote Won't Stay

Just got a brand new iMac. I went to stick the apple remote on the side of the iMac and it won't stick. I have no clue why, any body have any explanation or should i just bring it in to apple and probably get the magnet repaired.

This is just a long shot, but I suppose someone may have failed to actually install the magnet.
Have you checked to see if it is actually there? Get some light magnetic material, or better yet a real magnet. First run it the magnet from the bottom edge upwards to the CD slot to see if you get a reaction. If not there is a good chance the magnet that was supposed to be in the iMac was overlooked at the factory.
If you do get a reaction, then try the magnet against the back of your remote. If the remote won't stick then someone may have failed to to instal the magnetic strip in the remote.
Doug

Similar Messages

IPhone Remote Won't Stay Connected to Apple TV

I have an apple tv, iphone 3gs and ipod touch first gen.
I am having many issues using either the ipod or iphone as the remote.
When I have connected to the the apple tv itunes library with the iphone's remote app it works fine. But as soon as either the apple tv or iphone fall asleep, turn off or disconnect they lose each other. I then cannot re-connect to the apple tv's itunes library. I am still able to connect to another itunes library but not the apple tv.
The only way I can manage to connect to the apple tv library with the iphone again is by resetting both devices and unpairing them. Then I am able to put the four digit code in again, works fine untill it goes to sleep. A big circle!
I have installed the app on my first gen ipod touch, however the app just won't open. I have purchased the 3.0 software for the touch, but the app doesn't work on it.
I am very much at a loss.
I would appreciate any help or tips. I have tried opening the two ports apple suggests opening. However that does not help.
Thanks,
Syd

I too have the same issue. I could connect to either iTunes or Apple TV, but as soon as I got out of one or the other I could never get it to connect to the library. I spent hours messing with my router, and nothing worked.
I did notice that my iPod Touch (which is running 3.0 firmware) had no problems at all connecting to either libraries. So I knew it wasn't a firewall issue.
The only think I found to work (and was the easiest workaround) was to go on the iPhone Settings > Wi-Fi and turn off Wi-Fi for about 10 seconds. After turning it back on and the phone reconnected to the Wi-Fi network, I could immediately connect to Apple TV or iTunes. But as soon as I got out, the problem happened again.
I definitelly think there is some TCP/IP bug in the software that isn't meshing with the iPhone 3.1.2 firmware.
I hope this helps.

Can't get Apple Remote App to stay connected to my ITunes library.

I recently had my modem and router taken out by lightening. So I replaced them both with what is supposed to be the latest and greatest. Simultaneously, Apple had a new version of ITunes, so I updated. Now I can't get the Apple remote app to stay connected to ITunes. If I start ITunes on my computer, my IPhone 5 will see and connect to the library, as well as my IPad. But as soon as my IPhone or IPad goes to sleep and I try to reconnect to the library, it can't connect to the library. I've never had any connection problems before and not sure what is causing the problem. I can turn off Home Sharing in ITunes and turn it back on again, or restart ITunes and it works, but as soon as the IPhone or IPad goes to sleep, it won't reconnect again. Is this a router issue or ITunes Home Sharing issue? Any input to resolve this will be greatly appreciated..............because it is really annoying not to be able to control music the way I did before! All products have the latest updates.

Take it back and exchange it.
If the remote doesn't work out of the box new then either remote is faulty or AppleTV is faulty (eg IR sensor not located properly in the case).
Either way one of them isn't working, exchange it.

I have Dreamweaver CS5 with Windows 8 and it won't stay connected to the server and it says I need flash plug in, please help

I have a Gateway computer with Windows 8 installed. I have installed Dreamweaver CS5 to manage my website and it won't stay connected to the server. It also won't play flash and says I need a flash plug in. Please help

#1 Try toggling Passive FTP on/off in your remote server's site definition.
#2 Except for a handful of gaming sites, Flash is a dead web technology. It's not supported by iPhone, iPad, iTouch, Android, etc... I don't recommend using Flash for anything these days. Better to use HTML5, CSS level 3 and JavaScript.
Nancy O.

Apple TV won't stay in standby

Whenever I put Apple TV on standby then exit and go to watch TV or a DVD within minutes the Apple TV has powered up again. It won't stay in standby mode.
Any suggestions?

Having the same issue. Holding play also no longer seems to work in putting ATV into standby mode, and now requires going to the menu selection. But as soon as another button is touched on my remote, ATV lights back up.

Highlighting text won't stay on

When I highlight text it often won't stay on, and when it does and I try to move the selection, it just beeps at me and sits there. What's up?

Ok. In System Preferences > General, Apple applies the term “Highlight” instead of “Selection” color.
In Pages v5(.2), I select a passage of text and it reflects my first sentence color setting. You can leave this alone and visit any menu or side panel setting, and the selection in the body text will remain selected. It will remain selected, if you leave the Pages document and click in another application. When you return to this Pages document, click anywhere but the body text to regain document focus. The next click in the body text should be a click/hold/drag on the selection to move it, or a press of the space bar to remove the selected text. This is mouse-based behavior.
If you are using a Trackpad, whether built-in or external, you must be very careful not to brush against it while in your Pages document, or your selection focus will be lost.
I am using the above Pages on OS X 10.9.4 and do not experience a loss of selection, or an inability to drag/move or remove the selection. I have tried with both mouse and Trackpad following the preceding guidelines and cannot reproduce what you have stated.

New Pioneer DVR-110 installed, "patchburned", BUT drive won't stay closed.

Have had some good advice on how to intall a new DVD/CD drive, but after installing a New Pioneer DVR-110 (I thought succesfully) on my G4, and downloading Patchburn for Panther, the DVD drive now won't function as the computer keeps ejecting or opening the drive tray.
After installing the drive, I installed Patchburn, and Toast did recognize the drive. I then tried to verify disc permissions on the computer and it kept getting hung up during repair/verify saying it lost connection with the drive manager. Tried Onyx to repair/verify permissions and it too gets hung up. (Had to force quit)
Any advice on how to get the drawer of the DVD drive to stay closed and what else I need to do to get it working?... Alas I can not even reinstall my original OSX software now as I can't boot from the disc drive since it won't stay closed.
Thanks, Rob
G-4 Quicksilver Mac OS X (10.3.9)

You can verify the closeness by opening the empty drive door with the KB and then hold the door open and close drawer with the KB.

My Itunes will not stay open, I have uninstalled it and reinstalled it and it still won't stay open

My Itunes will not stay open. Everytime I open it it just gives me a wait signal and then closes down on it's own. I have uninstalled it and reinstalled it and it still won't stay open.... what should I do now?

Try removing the Genius database. In the "Finder" go to the /username/Music/iTunes/ folder and delete the "iTunes Library Genius.itdb" file. This may allow the program to launch again. This file will be recreated upon first use of the "Genius" feature.

My spooler won't stay running, I can't add printers.

My spooler won't stay running, I can't add printers.
Not able to figure out even after firewall on/off, network on/off and all setting to default...
Regards
Reddy

find some possibility solution for spooler wont start here
https://social.technet.microsoft.com/Forums/en-US/d875ab83-1b17-4a28-8738-e67249a2bdfd/cannot-print-after-update-to-81-printers-gone-print-spooler-keeps-stopping-cannot-add?forum=w8itprohardware
I recommended this step
1. do printer troubleshooting
http://windows.microsoft.com/en-us/windows/printer-problems-in-windows-help#fix-printer-problems=windows-8&v1h=win8tab3&v2h=win7tab1&v3h=winvistatab1&v4h=winxptab1
2. Uninstall antivirus using removal tools (Kapersky)
3. Registry trick as
JSB43211 suggested, backup your registry before perform this
1. Open Regedit as Administrator
2. Find the HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Print\Environments\ key.
3. If you are on a 64-Bit machine, browse to the "Windows x64" sub-key (else "Windows NT x86")
4. Under the "Print Processors" sub-key DELETE ALL THE SUB-KEYS EXCEPT "winprint" key
5. Start the Print Spooler service.
6. Test to see if you can Add a printer.

I have a issue with my mac book pro. For some reason it won't stay powered on. I can't get past the apple loading logo. The battery is fully charged so it is not the problem. Can anyone tell me what the problem may be and how can i get it resolved?

I have a issue with my mac book pro. For some reason it won't stay powered on. I can't get past the apple loading logo. The battery is fully charged so it is not the problem. Can anyone tell me what the problem may be and how can i get it resolved?

The battery is fully charged so it is not the problem.
What happens when you use the MagSafe?

My iphoto quites unexpectedly everytime I open it and says closes while using the eOkaoFr.dylib plugin. Does anyone know how to fix this? iphoto won't stay open for more than 1 minute at a time.

My iphoto quites unexpectedly everytime I open it and says closes while using the eOkaoFr.dylib plugin. Does anyone know how to fix this? iphoto won't stay open for more than 1 minute at a time. Help anyone?

Is there a crash log? If so post the first 100 or so lines o fit
Do you know what the ofending plugin is? and where it came from?
LN

I currently have a DROID RAZR M and I'm 1 year into my 2 year contract. Since the Kitkat update, the phone won't stay charged and it's very buggy. I know this is not Verizons fault but it's also not mine. I would like to change my phone to an iPhone 5s

I currently have a DROID RAZR M and I'm 1 year into my 2 year contract. Since the Kitkat update, the phone won't stay charged and it's very buggy. I know this is not Verizons fault but it's also not mine. I would like to change my phone to an iPhone 5s and keep my same plan but switch to the Edge program. Is this possible? I don't think I should have to pay an early termination fee or anything like that since my phone has become almost unusable. I know under normal circumstances you have to wait 2 yrs to upgrade but due to the update and the poor service I'm now getting I hope Verizon can make an exception. Thank you.

How recently did you switch? If it's less than 60 days, then Verizon simply reinstates your previous account. The fact that you were on the EDGE plan and mailed the devices back, and they apparently are somewhere in the system, could cause complications, and it might just work out that you just go back on the same plan and they set you up with the same devices. I'm not sure how it will go - but since you are still being billed for the devices...

IPod Nano won't stay mounted

Hi this is my first post and hope someone can help. My problem is that when I attach my nano to my computer it will mount on the desktop, open iTunes check and see that it is update, which it is and then it umounts from the desktop within a few seconds. It remains in the iTunes window so I can access the nano preferences but then when I hit apply it searches for the nano and since it is not on the desktop says it can not find it. The iPod is not in the finder window but shows up in the system profiler as being attached to the USB. I am up to date on iTunes and the nano updater says it is up to date running 2006-06-28. I have tried everything such as restarting, using different USB ports, etc... to no avail. When I run the updater it stays mounted on the desktop but I can not acces the preferences. I really need to change my nano preferences as it will not update my new playlists because prefs, are set to update only the checked ones and I can not changes this and apply it if the nano won't stay mounted. Can anyone help? Much thanks

This happened to me when using iTunes 6. Is that the version you are using? I was never able to find a complete answer to the "Preferences not saved" error or any knowledge base articles with an official explanation. I did however find a workaround in a previous discussion. Connect your iPod and in the short time that it is still visible on the desktop just as iTunes is opening, go to Preferences>iPod and tick "enable disk use". You have to be quick but it can be done. Once it is enabled you will be able to go back and update the preferences such as manual update etc. and and you'll not get the error.
If you are using iTunes 7 try the same technique only tick "enable disk use" in the Summary tab before your iPod unmounts.

I updated my iPhone 5 software and now it won't stay connected to wi-fi

I updated my iPhone 5 software and now it won't stay connected to wi-fi

Icloud uses you Apple ID. It one of the Key feature on the new ATV. Restart the ATV, if that doesn't work unplug it and restart it. It should resolve the issue

How can I wipe a drive on an old iMac that won't stay on long enough to complete the task?

How can I wipe a drive on an old iMac that won't stay on long enough to complete the task?

Do you have access to another Mac? If so contact the two via a Firewire cable, boot your problem Mac into Target Disk Mode, Transferring files between two computers using FireWire,, and try to use Disk Utiltiy from the second Mac to reformat and erase your hard drive.

Remote Won't Stay

Similar Messages

Maybe you are looking for