RemoteApp to Windows 2012 RDGateway to Windows 2008 RD Web

I am trying to add in windows 7 a connection to the RD web server and am receiving "An error occurred" when pointing to the RD gateway. If I point to the RD Web server it works.
The setup is a 2012 RD Gateway server in the DMZ that is accessible from the internet and a 2008 RD Web server internally. If I login in via the web to the 2012 gateway server I am able to see the list of published apps. If I point a windows 7 workstation
to the gateway to pull the published apps it fails. If I point the client to the internal server it works.

Hi,
Please check if you install the latest updates of RDP for the Windows 7 clients.
Description of the Remote Desktop Protocol 8.0 update for Windows 7 SP1 and Windows Server 2008 R2 SP1
http://support.microsoft.com/kb/2592687
Update for RemoteApp and Desktop Connections feature is available for Windows
http://support.microsoft.com/KB/2830477
Hope this helps.
Jeremy Wu
TechNet Community Support

Similar Messages

Upgrade of Integation Services (Windows 2012 R2) on Windows 2008 R2 with Exchange 2013 SP1 DAG fails

Here is the scenario:
Legacy Host: Windows 2008 R2
Guest VM: Windows 2008 R2 with Exchange 2013 SP1 DAG cluster.
After importing the VM (2008 R2 and Exchange 2013 DAG) into a 2012 R2 host (Cluster). (copy VM files to new 2012 R2host) Everything works fine.
Then upgrading "Installation Services" (for Windows 2012 R2 host) on the imported VM runs fine with no errors to the "Restart" prompt. VM than shows: "Configuring Windows updates 32% complete. Do not turn
of your computer." Hangs there for about 20 minutes until is says "shutting down". Hangs there for 20 minutes until power off. Restart to normal start; "Preparing to configure Windows. Do not turnoff your computer." proceeds slowly
to "Configuring Windows updates 32% complete. Do not turn of your computer." hangs there again indefinite. Sometime hangs at shutdown cycle and "Configuring Windows updates 32% complete. Do not turn of your computer." indefinitely.
I moved 20 other machines from a 2008 R2 host to new Windows 2012 R2 hosts all of these machines install the 2012 R2 Integration services just fine on the 2008 R2 VM. Just the 2008 R2 VMs clustered (DAG) and Exchange 2013 SP1 do not take the Integration
Services upgrade.
Any advise from Microsoft? I know I could decommission the DAG and Exchange machines and install Integration services on the native box before Exchange and DAG and that would sure work, but I'd rather avoid that amount of work for a simple integration layer
upgrade.
Thanks
Gerhard Waterkamp ACSLA Inc.

Hi,
Could you try use the following method to fix this issue first?
1. Run the System Update Readiness Tool, then check if there is any error in the Checksur.log and checksur.persist.log.
1. Please run the System Update Readiness Tool on this affected server. Please download this tool from the following Microsoft article:
Description of the System Update Readiness Tool for Windows Vista, for Windows Server 2008, and for Windows 7
http://support.microsoft.com/kb/947821/en-us
2. The System Update Readiness Tool creates the log files that captures any issues that the tool found or fixed. The log files are located at the following location:
%SYSTEMROOT%\Logs\CBS\
3. Please paste the checksur.log here for analysis.
If there is no error found, please try the following step.
==================================
2. Use Fix it tool to reset the Windows Update components.
1. Open the following link.
http://support.microsoft.com/kb/971058/en-nz
2. Select Windows 8.1, Windows 8 and Windows 7 in the product selection box.
3. Click “Run Now” to reset the Windows Update components.
Note: We can reset the Windows Updates manually by following the steps in the KB above.
3. Use the System File Checker tool to repair missing or corrupted system files
1. Open the command promote with Administrators.
2. At the command prompt, type the following command, and then press ENTER:
sfc /scannow
Any errors are found in the steps above, please let me know.
Hope this helpful.
Best Regards,
Jason Zeng
Please remember to click “Mark as Answer” on the post that helps you, and to click “Unmark as Answer” if a marked post does not actually answer your question. This can be beneficial to other community members reading the thread.

Windows 2012 Activation from Windows 2008 R2 KMS server

Hello,
We have 2 KMS servers in our Domain. One has server has KMS key for Windows 2012 KMS installed and other not.
I have joined first windows 2012 server to domain and its been 3 hours the server is still not activated from KMS server.
When client contacts KMS server for Windows 2012 licnese, if key is not installed on first KMS server, will it automatically contact second one? Do I need to change sonmething?
One more question:
Is it possible to have Windows 2012 key installed on the same KMS server, which is already acting as KMS sertver for Windows 2008R2? and Windows 2003 R2? or wil this cause any issues?
Mahi

Hello,
Once a KMS host is activated, it will publish it's record to DNS. KMS clients attempting to activate will query DNS to get a KMS host, if there is more than one, they will use the first one they get. The DNS server should be rotating which records
it hands out.
If they activate, they will cache that record and attempt to use it when they renew, if they fail to renew or activate, they will query DNS for the KMS host again.
Since this is a new KMS host it will need at least 5 KMS clients to contact it meet the count needs for Server.
What version of Windows is the other KMS host machine is it Windows Server 2008, Windows Server 2008 R2 or is it Windows Server 2003 R2?
Thanks, Darrell Gorter [MSFT] This posting is provided "AS IS" with no warranties, and confers no rights.

Hyper-v cannot boot Gen2 guest from Windows 2012 R2 or Windows 8.1 x64 ISO - file format not supported, Gen1 works fine

I am new to Gen2 Hyper-V and so far I simply can't use it, because I am unable to install any (supported) guest OS from an ISO ...
So far I tried that on:
1. my HP Z230/i4770 workstation (Secure Boot disabled) host running Windows 8.1 Pro x64 (with Hyper-V feature enabled), can't boot any VM with supported OS ISO.
2. my home desktop/i3770K (secure Boot enabled) host running Windows 8.1 Pro x64, same result, error during VM boot from ISO, quoted below.
Synthetic SCSI controller (instance blah blah) Failed to Power on with Error 'The version does not support this version of file format'
Gen1 guests of course work perfectly fine with those ISOs, because emulated DVD IDE picks up the official Enterprise Evaluation ISO of either Windows Server 2012 R2 or Windows 8.1 x64 Enterprise, perfectly fine and all works OK in Legacy boot mode.
When I create a new guest and select Gen2, then no matter if I check or uncheck the Secure Boot in virtual Boot Order options for the guest (while setting the SCSI DVD at top of course), it simply doesn't work, always same error. I tried first connecting
to VM to see if it prompts for key press, but it doesn't, the error is instant on Power on when (supported) ISO image is selected to be booted.
I verified that both of official Enterprise Evaluation ISO's of either WS2012r2 and W8.1x64 are bootable in both the UEFI mode (Secure Boot enabled) and Legacy BIOS mode using a physical computer.
What am I missing here???

FYI, above is wrong! it's not about linking ISO to virtual DVD or selecting "Install OS later", it's all about the location of the ISO file and share permissions on parent folder!
I was actually suspecting several issues, but haven't had time to test it, was thinking about issues like assigning (or not) some of initial settings during Gen2 VM creation, e.g.:
-Network connection through virtual switch or Not Connected (make no different if assigned or not)
-Memory above 4096MB (makes no difference if < or > 4096MB)
-ISO file location (makes huge difference!)
The ISO file CANNOT be placed on network share OR in shared folder on same local drive as the VHDX file (works fine if parent folder is not shared).
I can now replicate the issue easily every time and it always fails with file format unsupported message whenever I have the ISO file located either on remote network share, or (fails the same way too) when I have the ISO file placed locally (on host drive)
when simply a parent folder is shared... must be some permissions issue... and a pretty dumb one considering that in production environments nearly everything is placed on remote file servers ...
... so the moral of the story is, if you want to install Gen2 VM in win8/2012 hyper-V then you must copy the ISO file to Hyper-V host drive AND make sure the parent folder is not shared. works every time now! :)

Can I migrate physical hard disks in storage space from Windows 2012 R2 to Windows 2012?

Hi,
We have a Windows 2012 R2 server. It's running storage space with 10 hard disk in Parity mode. We would like to move the hard disks from Windows 2012 R2 server to Windows 2012, so that we can "free" our windows
2012 R2 server to do something else. Can we just unplug the hard disks in Windows 2012 R2 and hook it to Windows 2012 server without any data lose? If we can do it, what's best "formal" procedures to do it?
Thanks,
Tak

Hi Tak,
Storage space will be recognized in different servers (and even clients) which support.
If it is just a "Parity mode", you can turn off the computer, unplug and connect these disks to the new server directly.
If any Windows Server 2012 R2 new feature is involved, it may not work in Windows Server 2012 but it should not damage your data and you can still connect these hard disks back to original server.
However, backup important files is always recommended.
If you have any feedback on our support, please send to [email protected]

Downgrade of Windows 2012 r2 to Windows 2012 Domain Service Active Directory

I have an uncertainty. we used adprep /forest and adprep /domain tools on windows 2012 R2 to update the domain active directory. But after promoting a domain controller to windows 2012 R2, we realized that a tool we use to authenticate computer account not
supported for domain controllers in Windows 2012 R2. Here comes the question, I can to install direct and promote a domain controller windows 2012 without running the adprep /forest and adprep /domain tools of Windows 2012?.
I hope be clearly.
tks.
migrations

Hello,
as others mentioned there is no problem to promote a Windows Server 2012 into the domain as the functional level is fine for this.
Best regards
Meinolf Weber
MVP, MCP, MCTS
Microsoft MVP - Directory Services
My Blog: http://msmvps.com/blogs/mweber/
Disclaimer: This posting is provided AS IS with no warranties or guarantees and confers no rights.

Inplace upgrade Windows 2012 DC to Windows 2012 R2

Hi
We plan to upgrade some of our DCs from Windows 2012 to Windows 2012 R2.
Theese DCs is on a DMZ holding our virtual machines management servers so they are not the most critical DCs but they are critical enough to not working for a longer time.
Normally we dont do inplace upgrade but this is more of quick solution to raise the servers to the same OS level
So has anyone done an inplace upgrade from 2012 to 2012 R2 on domain controllers? Any problems?
We have two DCs, in differents locations.
BR

Yes, we've upgraded some of our DC's from Server 2012 to Server 2012 R2 without any issues at all. Obviously you want to do them one at a time, but we found it completely straight forward.
In fact, if it wasn't for some unrelated legacy issues at one site (old servers preventing us upgrading that sites DPM install as DPM 2012 R2 doesn't support them, but DPM 2012 doesn't support Server 2012 R2) we'd have upgraded all our DCs by now.

Downgrade Windows 2012 Server to Windows 2008 Server

Hello,
I can see this topic covered but the pervious answers are not solving my problem.
A client purchased Server 2012 standard OEM from us (distributor), he want to downgrade to Server 2008 STD.
They called the MS Activation Center and received the answer that for OEM the downgrade is not available. We called the Activation Center and we received the same answer.
Thank you in advance
Regards

What's your question? It appears the Activation Center provided the answer but you did not like it?
As an OEM, you should be aware that OEM licenses have some built-in restrictions. For detailed answers to questions you have, you should talk with your Microsoft representative.
.:|:.:|:. tim

Slow logons on windows 2012 server and windows 7 sp 1 devivce

Hello everybody,
I've a windows user reporting slow logons on one of our clients.
The domain is a 2012 domain and the device with the issue is a windows 7 sp1.
The winlogon message event ID 6005 appears (winlogon taking too long to handle notification request)
Also NETLOGON message event id 5719 saying can not secure channel with the DC, because there're no one available).
Profile is not set to roaming.
The system logs are uploaded to this link:
https://onedrive.live.com/redir?resid=2CDBBADCC474A82C!241&authkey=!AM99cXm2AaNp8Wg&ithint=folder%2czip
Resetting the password of the computer object is succesfull but I can not be resetting the password now and then.
The GP setting for process login scripts synchronously is not configured.
The GP setting that makes the computer wait for the network set to 0 then causes a temp profile to be loaded.
Please help me I don't know what else to do.
Regards

Hello Britt,
Thanks a lot for answering.
Looking at the DNS server found no reverse lookup zone configured. I didn't setup the server so I didn't know that. I did a search and AD seems to have no problem with that.
Here's an ipconfig from the SERVER:
Windows IP Configuration
   Host Name . . . . . . . . . . . . : Server
   Primary Dns Suffix . . . . . . . : NEPedi.local
   Node Type . . . . . . . . . . . . : Hybrid
   IP Routing Enabled. . . . . . . . : No
   WINS Proxy Enabled. . . . . . . . : No
   DNS Suffix Search List. . . . . . : NEPedi.local
Ethernet adapter NIC1:
   Connection-specific DNS Suffix . :
   Description . . . . . . . . . . . : Broadcom NetXtreme Gigabit Ethernet #2
   Physical Address. . . . . . . . . : F0-1F-AF-E4-C4-FF
   DHCP Enabled. . . . . . . . . . . : No
   Autoconfiguration Enabled . . . . : Yes
   Link-local IPv6 Address . . . . . : fe80::586e:e054:8cb2:fd10%13(Preferred)
   IPv4 Address. . . . . . . . . . . : 192.168.2.10(Preferred)
   Subnet Mask . . . . . . . . . . . : 255.255.255.0
   Default Gateway . . . . . . . . . : 192.168.2.1
   DHCPv6 IAID . . . . . . . . . . . : 384835503
   DHCPv6 Client DUID. . . . . . . . : 00-01-00-01-1A-95-A4-94-F0-1F-AF-E4-C5-00
   DNS Servers . . . . . . . . . . . : ::1
                                       127.0.0.1
                                       8.8.8.8
   NetBIOS over Tcpip. . . . . . . . : Enabled
Tunnel adapter Local Area Connection* 12:
   Media State . . . . . . . . . . . : Media disconnected
   Connection-specific DNS Suffix . :
   Description . . . . . . . . . . . : Teredo Tunneling Pseudo-Interface
   Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0
   DHCP Enabled. . . . . . . . . . . : No
   Autoconfiguration Enabled . . . . : Yes
Tunnel adapter isatap.{2C549BDD-1164-4933-8E08-A725CB8E4CB4}:
   Media State . . . . . . . . . . . : Media disconnected
   Connection-specific DNS Suffix . :
   Description . . . . . . . . . . . : Microsoft ISATAP Adapter #3
   Physical Address. . . . . . . . . : 00-00-00-00-00-00-00-E0
   DHCP Enabled. . . . . . . . . . . : No
   Autoconfiguration Enabled . . . . : Yes
And the client has this parameters configured:
Network Adapter  Intel(R) 82578DM Gigabit Network Connection
IP Address   192.168.2.135
MAC Address   84:2B:2B:C3:2C:8B
Gateway   192.168.2.1
DHCP Enabled   Yes
DHCP Server   192.168.2.1
DHCP Lease Expires  09/26/2014 09:01:07 AM
DHCP Lease Obtained  09/24/2014 09:01:07 AM
DNS Server Search Order  192.168.2.10
IP Enabled    Yes
IP Subnet    255.255.255.0
WINS Primary Server
WINS Secondary Server
Last Check Date  9/25/2014 12:01:47 AM
I'll post a complete ipconfig from the client later, because I have to remote in and now it's not available.
Regards.

How to activate Windows 8.1 on a Windows 2008 R2 KMS server when I don't have Windows 2012 R2 kms host key

I only have windows 8.1 kms host key but I can't add a client OS kms key to Windows 2008 R2 kms server. And I don't have Windows 2012 R2 license either. Is there any way I can activate Windows 8.1 using my existing kms server? Thanks.

I would like a yes no clarification answer. So does this mean that EVEN WITH THE PATCH. My Server 2012 Standard edition that currently hosts KMS VA for clients running Win7, Win 8, Office15, Server 2008, Server 2012. Will not be able to host windows 8.1?
I will have to install 8.1 and use as a host?
if you have a KMShost product key for WS2012R2, you can patch a down=level Server and be fine.
(the OP didn't renew SA or otherwise has no KMShost pkey for WS2012R2)
Don
(Please take a moment to "Vote as Helpful" and/or "Mark as Answer", where applicable.
This helps the community, keeps the forums tidy, and recognises useful contributions. Thanks!)
I'm having similar issues and have a similar question that doesn't seem to be answered:
My KMS server is Windows 2008 R2 (Also is my domain controller). I want to activate Windows 2012 R2 and Windows 8.1 machines off this KMS server. I can install the 2012 R2 key just fine but receive error 0xC004F015 (The Software Licensing Service reported
that the license is not installed) when I try to install my 8.1 KMS key.
What I'm gathering from this thread is that I have to set up a Windows 8.1 host and set it up to be a KMS server exclusively for activating Windows 8.1. Is this correct? If so, Microsoft needs to fix that. I have a SERVER for activations for a reason: it
is a server, not a client. If I am mis-understanding, how do I get my Windows 2008 R2 server to accept the Windows 8.1 KMS key for activating 8.1 clients?
Thanks!
You don't need Windows 8.1 KMS key. Your 2012 R2 KMS key will be able to activate your Windows 8.1 machines. So your current set up is fine, no need to set up another Windows 8.1 KMS host.
My problem is I don't have 2012 R2 KMS key as I didn't buy any Windows 2012 R2 license. So I can't use 2012 R2 KMS key to activate my Windows 8.1.
Oh that's interesting. I guess I need to play around more because my 8.1 test machine isn't activating. I'll start a new thread for that if needed. Sorry for the confusion.

SCEP 2012 Client in Windows 8 / 2012 - in Windows 2008 Domain- Not Syncing -/ Not Compatiable

Dear All ,
With lots of Hardship I had installed SCEp 2012 in Windows 2012 Virtual machine in WIndows 2008 Domain.
SCCM 2012 Server in Windows 2008 Server with Sql 2008 was - performing well and there was no issues until our COmpany planned to Convert the Windows 2008 Server to Windows 2012 Server ( AD is 2008)
WSUS is not Fully synching with SCCM 2012 ( previously it was )
Software Updates not pushing properly and to top all the SCEP client is not compatible with win 8.1 pro or win 2012 server
Error: Failed to download content id 16787046. Error: Access is denied.
Package:
Success: The software updates were placed in the existing package:
• Deployment Package(JUN2014)
Software updates that will be downloaded from the internet
Error: Update for Forefront Endpoint Protection 2010 Client - 4.1.522.0 (KB2780435)
Errors
Failed to download content id 16787046. Error: Access is denied.
Language Selection:
English
But the service account has full access - administrative rights and the administrator of the system
please advise on this

Hi,
All the software updates downloaded failed?
Are there any errors in PatchDownloader.log? If you use Automatic deployment rule, please also check ruleengine.log.
Please add the account with Full rights to the source share (both NTFS and Share permissions) where the Deployment Package is located.
Best Regards,
Joyce
We
are trying to better understand customer views on social support experience, so your participation in this
interview project would be greatly appreciated if you have time.
Thanks for helping make community forums a great place.

Is SharePoint 2010 Supported on Windows 2012 R2

Hi
I have read Trevor Seward's responses to various questions on this subject :-
http://social.technet.microsoft.com/Forums/en-US/ad4e17ee-83de-41d6-a974-244ceccb8a63/is-sharepoint-2010-sp1-is-supported-by-windows-server-2012-currently-i-have-os-version-of-server?forum=sharepointadminprevious
http://social.technet.microsoft.com/Forums/en-US/e7539d34-aaa2-4d9c-a44c-e65d388d8944/support-for-sharepoint-foundation-2010-on-windows-server-2012-r2?forum=sharepointadminprevious
However, we have a farm which is currently SP2010 SP1 which we are about to upgrade to SP2010 SP2 running on Windows Server 2008R2 and SQL Server 2008 R2. So the farm is currently not supported by Microsoft.
We are now looking to upgrade this farm to SP2013 SP1 running Windows Server 2012 R2 and SQL Server 2012.
We plan to start this process of by upgrading Windows Server 2008 R2 to Windows Server 2012 R2.
Will SharePoint 2010 SP2 run on Windows 2012 R2 (or will we need Windows 2012) ?
Once Server 2012 R2 (or Server 2012) is up and running, we will upgrade SP2010 SP2 to Sp2013 SP1.
Finally upgrade SQL Server 2008R2 to SQL Server 2012.
So the part I don't know is will SharePoint 2010 SP2 run on Windows 2012 R2 or Windows 2012 ?
Thanks
Nigel
Nigel Price NJPEnterprises

Not a question for the Windows Server people. This is a question for the SharePoint people. You may want to try asking in a SharePoint forum like
http://social.technet.microsoft.com/Forums/en-US/home?forum=sharepointadminprevious
. : | : . : | : . tim

Windows 2012 System State Backup Fails

We have a Windows 2012 Domain Controller VM that we would like to backup the System State using DPM. Agent has been installed and the Windows Backup has been added.
When the backup runs in DPM, the job fails. Here is the error code:
DPM cannot create a backup because Windows Server Backup (WSB) on the protected computer encountered an error (WSB Event ID: 517, WSB Error Code: 0x12363C0). (ID 30229 Details: Internal error code: 0x80990ED0)
When we try and create the backup using Windows Backup, the following error is in the log file:
following error code '0x807800C5' (There was a failure in preparing the backup image of one of the volumes in the backup set.). Please review the event details for a solution, and then rerun the backup operation once the issue is resolved.
We have tried attaching a separate drive and backup to a shared location. Both fail.
We have tried backup of just a few files on the DC instead of the System State, this fails as well.
All VSS Writers show as Stable with no errors
Server has the latest updates
Server has been rebooted, same issue
VM is Windows 2012 on a Windows 2008 R2 clustered host and is using Dynamic Disks (not fixed disks).
Anyone have any thoughts on what could be going on?

Hi,
If any of the following are true, you will not be able to backup a system state to that volume.
• Make sure that the target volume has no shadow copy before the backup starts.
• If a system state backup is stored on a source volume, backup settings should be configured for full backups. By default, settings are configured for full backups.
• Periodically check that no other user or program maintains a shadow copy on the target volume.
• Do not keep volume level backups and system state backups in the same location.
• The volume used to store the system state backup needs twice the amount of free space as the size of the system state backup until the backup completes
Meanwhile please check if it is caused that you are backing up to a critical drive. Try modify the following key:
HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\wbengine\SystemStateBackup\
Set the value of this entry as follows:
Name: AllowSSBToAnyVolume
Data type: DWORD
Value data: 1
If you have any feedback on our support, please send to [email protected]

Exchange 2013 management tools installation on windows 2012 standard edition gives error.

Exchange 2013 management tools installation on windows 2012 standard edition gives following error.
Does anyone observed this issue ?
Error:
The Exchange management tools are supported on servers running Windows Server 2012 and Windows Server 2008 R2 SP1 or later, and also on Windows 8 and Windows 7 client computers.
For more information, visit: http://technet.microsoft.com/library(EXCHG.150)/ms.exch.setupreadiness.ValidOSVersionForAdminTools.aspx
My Test lab is having
Exchange 2013 installed (xyz.local) domain and working fine.
Now i am installing Exchange Management tools on server which is member of (xyz.local) Domain (base OS : Windows 2012 standard edition : Windows updated)
Best Regards
sameer Prabhune

Hi Sprabhune,
It should work.
Did you install the tool by GUI or cmd?
Please select "Automatically install Windows Server roles and features that are required to install Exchange Server" to have the Setup wizard install required Windows prerequisites.
If possible, please try to install the tool on Windows 7/8 client to test.
Exchange 2013 Prerequisites
http://technet.microsoft.com/en-us/library/bb691354.aspx
Frank Wang
TechNet Community Support

Officejet 6830 support for windows 2012

Can anyone assist with installation of HP officejet pro 6830 drivers/software on Windows 2012. The HP literature states that Windows 2012 is supported but here are no available drivers available for Windows 2012. The Windows 8.1 and 2008 drivers do not install in Windows 2012. Any assistance is appreciated.
This question was solved.
View Solution.

You can download the HP Printer Software for Officejet 6830 under the Win Server 2008 64 bit option :
http://h10025.www1.hp.com/ewfrf/wc/softwareDownloadIndex?softwareitem=bi-131212-2&cc=us&dlc=en&lc=en...
Please note that the installers for enterprise solutions must be extracted from the webpack and run from a command line
Here's the link to more details on how to install on Win Server environment for your reference :
http://h10025.www1.hp.com/ewfrf/wc/document?cc=us&lc=en&docname=c03351547
We are in the process to update the HP website to reflex the correct info.
Regards
If my answer was helpful please click on the "Thumbs up" button on the left to say "Thanks".
Click "Accept as Solution" if it solved your problem, so others can find it.
Although I am an HP employee, I am speaking for myself and not for HP.

RemoteApp to Windows 2012 RDGateway to Windows 2008 RD Web

Similar Messages

Maybe you are looking for