Removal of Auto Attendant ....

Hi Gurus,
I am having some problems with the UC 520 namely,
1) Is it possible to remove the auto attendant?
2) I would like when people call in to the main line, it would be diverted to a voice hunt group.
    The voice hunt group has already been configured as show below,
    voice hunt-group 1 sequential
    final 3399
    list 3309,3317,3318,3315
    timeout 10
    pilot 3380

I am not sure what do you mean by E1/T1?
Indeed i am using a DID service.
Here you go,
dial-peer cor custom
name internal
name local
name domestic
name international
name 900
name 976
dial-peer cor list call-internal
member internal
dial-peer cor list call-local
member local
dial-peer cor list call-domestic
member domestic
dial-peer cor list call-international
member international
dial-peer cor list call-900
member 900
dial-peer cor list call-976
member 976
dial-peer cor list user-internal
member internal
dial-peer cor list user-local
member internal
member local
dial-peer cor list user-domestic
member internal
member local
member domestic
dial-peer cor list user-international
member internal
member local
member domestic
member international
dial-peer cor list user900-internal
member internal
member 900
member 976
dial-peer cor list user900-local
member internal
member local
member 900
member 976
dial-peer cor list user900-domestic
member internal
member local
member domestic
member 900
member 976
dial-peer cor list user900-international
member internal
member local
member domestic
member international
member 900
member 976
dial-peer voice 2001 voip
description ** cue auto attendant number **
translation-profile outgoing PSTN_CallForwarding
destination-pattern 3398
b2bua   
session protocol sipv2
session target ipv4:IP ADDRESS
dtmf-relay sip-notify
codec g711ulaw
no vad  
dial-peer voice 150 pots
description ** incoming dial peer **
translation-profile incoming INCOMING_DID
incoming called-number .%
direct-inward-dial
port 0/3/0:15
dial-peer voice 2000 voip
description ** cue voicemail pilot number **
destination-pattern 3399
b2bua   
session protocol sipv2
session target ipv4:IP ADDRESS
dtmf-relay sip-notify
codec g711ulaw
no vad  
dial-peer voice 400 voip
description Office Tele
destination-pattern 4..
voice-class codec 1
session target ipv4:IP ADDRESS
dtmf-relay cisco-rtp
no vad  
dial-peer voice 500 voip
description TeleInformatics Voicemail
destination-pattern 5..
session target ipv4:IP ADDRESS
dtmf-relay cisco-rtp
no vad  
dial-peer voice 6 voip
description Oilexec
preference 7
destination-pattern 6..
session target ipv4:IP ADDRESS
dtmf-relay cisco-rtp
no vad  
dial-peer voice 31 voip
description London Office internal Extensions 31**
destination-pattern 31..
voice-class codec 1
session protocol sipv2
session target ipv4:IP ADDRESS
dtmf-relay sip-notify
dial-peer voice 32 voip
description Jersey Office internal Extensions 32**
destination-pattern 32..
voice-class codec 1
session target ipv4:IP ADDRESS
dtmf-relay cisco-rtp
no vad  
dial-peer voice 199 voip
description Aberdeen Reception phone
destination-pattern 199
voice-class codec 2
session protocol sipv2
session target ipv4:IP ADDRESS
dtmf-relay sip-notify
dial-peer voice 151 pots
corlist outgoing call-local
description ** E1 pots dial-peer **
translation-profile outgoing OUTGOING_DID
preference 5
destination-pattern 9[5-9]T
port 0/3/0:15
no sip-register
dial-peer voice 153 pots
corlist outgoing call-international
description ** E1 pots dial-peer **
translation-profile outgoing OUTGOING_DID
preference 5
destination-pattern 9001T
port 0/3/0:15
prefix 001
no sip-register
dial-peer voice 8 voip
description SIP Link to Regent Quay - ABZ Dial-tone
translation-profile outgoing VOIP_ABERDEEN
destination-pattern 8T
voice-class codec 1
session protocol sipv2
session target ipv4:IP ADDRESS
dtmf-relay sip-notify
clid network-number 12345678912
dial-peer voice 201 voip
description C-MAR internal Extensions 2**
destination-pattern 2..
voice-class codec 2
session protocol sipv2
session target ipv4:172.16.0.1
dtmf-relay sip-notify
dial-peer voice 154 pots
corlist outgoing call-international
description ** E1 pots dial-peer **
translation-profile outgoing OUTGOING_DID
destination-pattern 9019T
port 0/3/0:15
prefix 019
no sip-register
dial-peer voice 155 pots
corlist outgoing call-local
description ** E1 pots dial-peer **
translation-profile outgoing OUTGOING_DID
destination-pattern 91800T
port 0/3/0:15
prefix 1800
no sip-register
dial-peer voice 156 pots
corlist outgoing call-local
description ** E1 pots dial-peer **
translation-profile outgoing OUTGOING_DID
preference 5
destination-pattern 9100
port 0/3/0:15
forward-digits 3
no sip-register
dial-peer voice 2002 voip
description ** cue auto attendant number **
translation-profile outgoing PSTN_CallForwarding
destination-pattern 3397
b2bua   
session protocol sipv2
session target ipv4:10.1.12.1
dtmf-relay sip-notify
codec g711ulaw
no vad  
dial-peer voice 2003 pots
destination-pattern 3301
port 0/0/0
dial-peer voice 10 pots
destination-pattern 3301
port 0/0/0
dial-peer voice 157 pots
description ** FAX 1**
destination-pattern 9012T
port 0/3/0:15
prefix 012
dial-peer voice 158 pots
description ** FAX 2 **
destination-pattern 9013T
port 0/3/0:15
prefix 013
dial-peer voice 159 pots
destination-pattern 916..
port 0/3/0:15
forward-digits 4
dial-peer voice 34 voip
description wellington Office internal Extensions 34**
destination-pattern 34..
voice-class codec 1
session target ipv4:IP ADDRESS
dtmf-relay cisco-rtp
no vad  
dial-peer voice 35 voip
description Dubai Office internal Extensions 35**
destination-pattern 35..
session target ipv4:IP ADDRESS
dtmf-relay cisco-rtp
no vad  
dial-peer voice 37 voip
description Mumbai Office internal Extensions 37**
destination-pattern 37..
voice-class codec 1
session target ipv4:IP ADDRESS
dtmf-relay h245-alphanumeric
no vad  
dial-peer voice 30 voip
description Houston Office internal Extensions 30**
destination-pattern 30..
voice-class codec 1
session target ipv4:IP ADDRESS
dtmf-relay cisco-rtp
no vad  
dial-peer voice 38 voip
description Brasil Office internal Extensions 38**
destination-pattern 38..
session target ipv4:IP ADDRESS
dtmf-relay cisco-rtp
codec g711ulaw
no vad  
no dial-peer outbound status-check pots
sip-ua   
registrar ipv4:172.16.3.1 expires 3600

Similar Messages

  • ECP could not save UM Auto Attendant "Your request couldn`t be completed. Please try again in a few minutes"

    Good Day.
    I have Exchange 2013 SP1 CU5, everything works fine except only one thing:
    1. ECP/UM/UM dial plan/UM Auto Attendant
    2. I am receiving error only when i am adding Prompt in Menu Navigation. In "Menu Navigation Entry" i could press "OK" button successfully, in "UM Auto Attendant" when i am pressing "Save" - "error. Your request
    couldn`t be completed. Please try again in a few minutes"
    I`ve already done:
    1. Checked IIS bindings
    2. Recycle ApplicationPools
    3. Restart IIS
    Nothing helps...

    Problem solved, in the prompt you shoudn`t use special charactes ^) ' " , / ' After i`1ve removed it from prompt everething saves ok.

  • Exchange 2013 Auto Attendant fails when using multiple languages

    Hi All,
    Trying to setup UM Auto Attendants as I had it in Exchange 2010, but cannot get it to work as I want.
    Here is my setup:
    Windows 2012 and Exchange 2013.
    Parent - Main Auto Attendant (80)
    Child - English Auto Attendant (81)
    Child - Swedish Auto Attendant (82)
    Child - Finnish Auto Attendant (83)
    All callers are first connected to 80 where they can select the language to continue with (press 81 for English, press 82 for Swedish, press 83 for Finnish).
    This is what I found out this far:
    - If I have English language selected on all Attendants everything works fine I can select all choices and everything works as it should.
    - If I select the proper language for the other languages (82 & 83) only the connection to 80 & 81 works. If I try to connect from 80 to 82 or 83 nothing happens (connection goes quiet) and the only solution to get UM to answer again is to restart the
    UM service on the server.
    Extra info/what I tested this far:
    - I reinstalled the extra language packs just to be sure there were no issues.
    - If I select Swedish or Finnish language on extension 80 they work fine, so the language packs seems to be OK.
    Ideas Anyone?
    //Ase

    Hi All,
    After installing CU1 for Exchange 2013 this behaviour changed a little bit. Instead of getting total freeze of the system I get an error message instead saying "System Error Occured" and then a hangup.
    I also find out that if I remove the checkbox "Set the auto attendant to respond to voice commands" for the extension 82 & 83 (Swedish & Finnish Auto Attendants) this error does not happen, but I like to use the voice commands....
    Also when the error occurs I get the following in the Event Log:
    The VoIP platform encountered an exception Microsoft.Exchange.UM.UMCommon.UMGrayException: A non-fatal exception occurred. For details, please see the inner exception. ---> System.InvalidOperationException: The language for the grammar does not match
    the language of the speech recognizer.
       at Microsoft.Speech.Recognition.RecognizerBase.ThrowIfSapiErrorCode(SAPIErrorCodes errorCode)
       at Microsoft.Speech.Recognition.FileGrammarContent.Load(SapiGrammar sapiGrammar, Boolean enabled, Single weight, Int32 priority)
       at Microsoft.Speech.Recognition.GrammarContent.Load(SapiGrammar sapiGrammar)
       at Microsoft.Speech.Recognition.Grammar.Load(SapiGrammar sapiGrammar, IRecognizerInternal recognizer)
       at Microsoft.Speech.Recognition.RecognizerBase.LoadGrammarIntoSapi(Grammar grammar)
       at Microsoft.Speech.Recognition.RecognizerBase.LoadGrammar(Grammar grammar)
       at Microsoft.Exchange.UM.UcmaPlatform.UcmaCallSession.PlayPromptsAndRecoSpeechSessionState.LoadGrammar(UMGrammar grammar)
       at Microsoft.Exchange.UM.UcmaPlatform.UcmaCallSession.PlayPromptsAndRecoSpeechSessionState.LoadGrammars()
       at Microsoft.Exchange.UM.UcmaPlatform.UcmaCallSession.PlayPromptsAndRecoSpeechSessionState.InternalStart()
       at Microsoft.Exchange.UM.UcmaPlatform.UcmaCallSession.SessionState.Start()
       at Microsoft.Exchange.UM.UcmaPlatform.UcmaCallSession.ChangeState(SessionState nextState)
       at Microsoft.Exchange.UM.UcmaPlatform.UcmaCallSession.PlayPrompts(ArrayList prompts, Int32 minDigits, Int32 maxDigits, Int32 timeout, String stopTones, Int32 interDigitTimeout, StopPatterns stopPatterns, Int32 startIdx, TimeSpan offset, List`1
    grammars, Boolean expetingSpeechInput, Int32 babbleTimeout, Boolean stopPromptOnBargeIn, String turnName, Int32 initialSilenceTimeout)
       at Microsoft.Exchange.UM.UMCore.SpeechMenu.PlayPrompts(ArrayList prompts, BaseUMCallSession vo)
       at Microsoft.Exchange.UM.UMCore.SpeechMenu.SpeechMenuStart(BaseUMCallSession vo)
       at Microsoft.Exchange.UM.UMCore.SpeechMenu.StartActivity(BaseUMCallSession vo, String refInfo)
       at Microsoft.Exchange.UM.UMCore.ActivityManager.ChangeActivity(ActivityBase next, BaseUMCallSession vo, String refInfo)
       at Microsoft.Exchange.UM.UMCore.TransitionBase.Execute(ActivityManager manager, BaseUMCallSession vo)
       at Microsoft.Exchange.UM.UMCore.Menu.OnComplete(BaseUMCallSession vo, UMCallSessionEventArgs voiceObjectEventArgs)
       at Microsoft.Exchange.UM.UMCore.Menu.StartActivity(BaseUMCallSession vo, String refInfo)
       at Microsoft.Exchange.UM.UMCore.ActivityManager.ChangeActivity(ActivityBase next, BaseUMCallSession vo, String refInfo)
       at Microsoft.Exchange.UM.UMCore.TransitionBase.Execute(ActivityManager manager, BaseUMCallSession vo)
       at Microsoft.Exchange.UM.UMCore.Menu.OnComplete(BaseUMCallSession vo, UMCallSessionEventArgs voiceObjectEventArgs)
       at Microsoft.Exchange.UM.UMCore.Menu.StartActivity(BaseUMCallSession vo, String refInfo)
       at Microsoft.Exchange.UM.UMCore.ActivityManager.ChangeActivity(ActivityBase next, BaseUMCallSession vo, String refInfo)
       at Microsoft.Exchange.UM.UMCore.ActivityBase.OnHeavyBlockingOperation(BaseUMCallSession vo, HeavyBlockingOperationEventArgs hboea)
       at Microsoft.Exchange.UM.UcmaPlatform.UcmaCallSession.HeavyBlockingOperationSessionState.CompleteFinalAsyncCallback()
       at Microsoft.Exchange.UM.UcmaPlatform.UcmaCallSession.SessionState.CompleteNonTeardownState()
       at Microsoft.Exchange.UM.UcmaPlatform.UcmaCallSession.<>c__DisplayClassf.<CatchAndFireOnError>b__b()
       at Microsoft.Exchange.Common.IL.ILUtil.DoTryFilterCatch(TryDelegate tryDelegate, FilterDelegate filterDelegate, CatchDelegate catchDelegate)
       --- End of inner exception stack trace ---
       at Microsoft.Exchange.UM.UMCommon.ExceptionHandling.ExceptionCatcher(Object exception)
       at Microsoft.Exchange.Common.IL.ILUtil.DoTryFilterCatch(TryDelegate tryDelegate, FilterDelegate filterDelegate, CatchDelegate catchDelegate)
       at Microsoft.Exchange.UM.UcmaPlatform.UcmaCallSession.CatchAndFireOnError(UserCodeDelegate function) during the call with ID "Y2M5Y2ZhYzYzMzc4ZTVhYmE0ZjE3MmVjYTVmYmRiZTM.". This exception occurred at the Microsoft Exchange Speech Engine VoIP
    platform during an event-based asynchronous operation submitted by the server. The server will attempt to recover from this exception. If this warning occurs frequently, contact Microsoft Product Support.
    Anyone with ideas that can help me forward?
    //Ase

  • Unity Connection Auto Attendant direct to voice mail, MWI issue

    hi,
    First time encountering this issue with call transfer from AA and MWI.
    An Auto Attendant have been setup for a branch office.  All employees at  the Branch office phones are assigned a DID.
    Customers can dial the 10 digit or  dial the main line (auto attendant) and then dial the last 4 digit extension to reach the employee.
    Problem I am having is there is a range of numbers that when being transferred from AA, goes directly to voicemail.   Also when there is a message  left on the voicemail, the MWI is not lit.  It does show the envelope icon and the  message "you have vociemail" on the phone display.
    I can call the DID directly and it does not go directly to voicemail but MWI is still not on when a message is left.
    This only happens within a range of numbers..  for example, I have 50 DID assigned to this office from XXX-XXX-0100 to XXX-XXX-0150.   Only the phones within the range of XXX-XXX-0120 to XXX-XXX-0130 have this issue with the AA going directly to vociemail and MWI not on when a message is left.
    For phones outside this range of numbers, AA transfer works fine and MWI works.
    anyone ran into this issue before?
    thank in advance.

    Hi,
    The range in which you are facing issue is  XXX-XXX-0120 to XXX-XXX-0130, just try to open any  one of the extension in this range and go to edit -- transfer rules -- standard/alternate (if alternate is enabled) -- Transfer calls -- may be this is set to Greetings. If so the transferred call goes to voicemail directly. Try enabling Extension.
    Just try this for one extension and see...
    Hope this helps, i had the same issue.
    Regards
    Jagadish G

  • Call forward to external number which has auto attendant

    Hi 
    I am a voice administrator in my company
    I want to forward all of my calls to my Other location's number.
    Other location has only POTS line and to reach my extension user needs to go through Auto attendant menu.
    Is it possible to enter a digit pattern in call forward destination in CUCM so that it can take care of Auto attendant menu of my Other location and land on my number?
    We have CUCM 8 running.
    Please help!!
    Ashwin

    Hello Ashwin,
    "Other location has only POTS line and to reach my extension user needs to go through Auto attendant menu."
    What type of phone system and voice mail is providing the auto attendant?
    How are the POTS lines(analog only correct?) terminated into the phone system?

  • AUto attendant not working

    Auto attendant not working .....
    If i assign AA script Transfer_v02.aef then i hear an just 1-2 seconds the script after that again it is just ringing ...
    Is there Option to set
    Please press the extension which you want to Call ...
    Eg: if i press 222 that time it should ring the 222 extension
    Please help this is the first time i am working on this stuff
    If i chnage the scrpt file then i can hear auto attendant not initiazlised..  please find the attched screen shot and back file for more details.
    Best Regards
    Shabeel

    Hi KMS, check the codec used between that GW using the FXO and the CTI RP.
    Check also the Calling Seach Space
    GW should be able to reach CTI Route Point and CTI ports partition.
    If you try other extension it works fine?

  • Multiple Schedules and Auto Attendant in UC560

    Dear all,
    I have configured two schedules in UC560 using CCA 3.0.1 (office_hours and break_time).  I have then configured two auto-attendants. AA1 is used for office_hours and AA2 for break_time.  AA1 is working fine.  However, when it is break time, AA2 is not being used, instead the menu for closed hours in AA1 is used.  If I swap office_hours and break_time as AA2 and AA1, then break_time is ok while office_hours settings do not work.
    Internally, I can dial both AA extension numbers and get the correct prompt.  The problem is when an external call comes in.
    Any ideas what I may be doing wrong?

    Hi Tiziana,
    Sorry, I should have been more specific. What you have there is the built in script editor express. You can download the standalone CUE script editor here:
    http://www.cisco.com/cisco/software/release.html?mdfid=282825559&softwareid=282774364&release=7.0.6&relind=AVAILABLE&rellifecycle=&reltype=latest
    Edit to add: I think there are also some sample scripts that may help you out there as well. Here is also the Unity Express Script Editor guide.
    Best,
    David

  • All off-silte call directly goes to Auto Attendant

        Hello  everyone,
    I have an issue with UC520. There is one PSTN line connected to the voice port 0/2/0, All dial out works fine,  All off-site calls goes directley to the Auto Attendant, however, interal dial-in works fine, I mean user can dial internal extension properly but not from offsite to insite.
    I was wondering if any one can help me.
    Here is the partal UC configuration:
    =~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2014.01.13 13:51:51 =~=~=~=~=~=~=~=~=~=~=~=
    sh run
    Building configuration...
    Current configuration : 31685 bytes
    dot11 syslog
    dot11 ssid uc520-data
    vlan 1
    authentication open
    dot11 ssid uc520-voice
    vlan 100
    authentication open
    ip source-route
    ip cef
    ip dhcp relay information trust-all
    ip dhcp excluded-address 10.1.1.1 10.1.1.10
    ip dhcp excluded-address 192.168.10.1 192.168.10.10
    ip dhcp pool phone
    network 10.1.1.0 255.255.255.0
    default-router 10.1.1.1
    option 150 ip 10.1.1.1
    ip dhcp pool data
    import all
    network 192.168.10.0 255.255.255.0
    default-router 192.168.10.1
    ip name-server 63.203.35.55
    ip inspect WAAS flush-timeout 10
    ip inspect name SDM_LOW dns
    ip inspect name SDM_LOW ftp
    ip inspect name SDM_LOW h323
    ip inspect name SDM_LOW https
    ip inspect name SDM_LOW icmp
    ip inspect name SDM_LOW imap
    ip inspect name SDM_LOW pop3
    ip inspect name SDM_LOW netshow
    ip inspect name SDM_LOW rcmd
    ip inspect name SDM_LOW realaudio
    ip inspect name SDM_LOW rtsp
    ip inspect name SDM_LOW esmtp
    ip inspect name SDM_LOW sqlnet
    ip inspect name SDM_LOW streamworks
    ip inspect name SDM_LOW tftp
    ip inspect name SDM_LOW tcp
    ip inspect name SDM_LOW udp router-traffic
    ip inspect name SDM_LOW vdolive
    no ipv6 cef
    multilink bundle-name authenticated
    stcapp ccm-group 1
    stcapp
    stcapp feature access-code
    stcapp supplementary-services
    port 0/0/0
    fallback-dn 301
    port 0/0/1
    fallback-dn 302
    port 0/0/2
    fallback-dn 303
    port 0/0/3
    fallback-dn 304
    trunk group ALL_BRI
    translation-profile outgoing PROFILE_ALL_BRI
    voice call send-alert
    voice rtp send-recv
    voice service voip
    sip
    no update-callerid
    voice class codec 1
    codec preference 2 g729r8
    voice class custom-cptone CCAjointone
    dualtone conference
    frequency 600 900
    cadence 300 150 300 100 300 50
    voice class custom-cptone CCAleavetone
    dualtone conference
    frequency 400 800
    cadence 400 50 200 50 200 50
    voice register global
    max-dn 56
    max-pool 14
    voice translation-rule 4
    rule 15 /^...$/ /0354434848/
    voice translation-rule 1000
    rule 1 /.*/ //
    voice translation-rule 1111
    voice translation-rule 1112
    rule 1 /^0/ /*/
    voice translation-rule 2222
    voice translation-profile CALLER_ID_TRANSLATION_PROFILE
    translate calling 1111
    voice translation-profile CallBlocking
    translate called 2222
    voice translation-profile OUTGOING_TRANSLATION_PROFILE
    translate called 1112
    voice translation-profile PROFILE_ALL_BRI
    translate calling 4
    voice translation-profile nondialable
    translate called 1000
    voice-card 0
    dspfarm
    dsp services dspfarm
    license udi pid UC520W-8U-2BRI-K9 sn FHK131827A2
    archive
    log config
    logging enable
    logging size 600
    hidekeys
    username cisco privilege 15 secret 5 $1$TC0B$LXMORw4u1vQpD/2eJdN4W1
    username admin privilege 15 password 0 admin
    username parham privilege 15 password 0 parham
    ip tftp source-interface Loopback0
    translation-rule 22
    bridge irb
    interface Loopback0
    description $FW_INSIDE$
    ip address 10.1.10.2 255.255.255.252
    ip access-group 101 in
    ip nat inside
    ip virtual-reassembly in
    interface FastEthernet0/0
    description $FW_OUTSIDE$
    ip address dhcp
    ip access-group 104 in
    ip nat outside
    ip inspect SDM_LOW out
    ip virtual-reassembly in
    duplex auto
    speed auto
    interface Integrated-Service-Engine0/0
    description cue is initialized with default IMAP group
    ip unnumbered Loopback0
    ip nat inside
    ip virtual-reassembly in
    service-module ip address 10.1.10.1 255.255.255.252
    service-module ip default-gateway 10.1.10.2
    interface FastEthernet0/1/0
    switchport voice vlan 100
    no ip address
    macro description cisco-phone
    spanning-tree portfast
    interface FastEthernet0/1/1
    switchport voice vlan 100
    no ip address
    macro description cisco-phone
    spanning-tree portfast
    interface FastEthernet0/1/2
    switchport voice vlan 100
    no ip address
    macro description cisco-phone
    spanning-tree portfast
    interface FastEthernet0/1/3
    switchport voice vlan 100
    no ip address
    macro description cisco-phone
    spanning-tree portfast
    interface FastEthernet0/1/4
    switchport voice vlan 100
    no ip address
    macro description cisco-phone
    spanning-tree portfast
    interface FastEthernet0/1/5
    switchport voice vlan 100
    no ip address
    macro description cisco-phone
    spanning-tree portfast
    interface FastEthernet0/1/6
    switchport voice vlan 100
    no ip address
    macro description cisco-phone
    spanning-tree portfast
    interface FastEthernet0/1/7
    switchport voice vlan 100
    no ip address
    macro description cisco-phone
    spanning-tree portfast
    interface FastEthernet0/1/8
    switchport mode trunk
    no ip address
    macro description cisco-switch
    interface BRI0/1/0
    no ip address
    isdn point-to-point-setup
    isdn incoming-voice voice
    isdn sending-complete
    interface BRI0/1/1
    no ip address
    isdn point-to-point-setup
    isdn incoming-voice voice
    isdn sending-complete
    interface Dot11Radio0/5/0
    no ip address
    ssid uc520-data
    ssid uc520-voice
    speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0 54.0
    station-role root
    interface Dot11Radio0/5/0.1
    encapsulation dot1Q 1 native
    bridge-group 1
    bridge-group 1 subscriber-loop-control
    bridge-group 1 spanning-disabled
    bridge-group 1 block-unknown-source
    no bridge-group 1 source-learning
    no bridge-group 1 unicast-flooding
    interface Dot11Radio0/5/0.100
    encapsulation dot1Q 100
    bridge-group 100
    bridge-group 100 subscriber-loop-control
    bridge-group 100 spanning-disabled
    bridge-group 100 block-unknown-source
    no bridge-group 100 source-learning
    no bridge-group 100 unicast-flooding
    interface Vlan1
    no ip address
    bridge-group 1
    bridge-group 1 spanning-disabled
    interface Vlan100
    no ip address
    bridge-group 100
    bridge-group 100 spanning-disabled
    interface BVI1
    description $FW_INSIDE$
    ip address 192.168.10.1 255.255.255.0
    ip access-group 102 in
    ip nat inside
    ip virtual-reassembly in
    interface BVI100
    description $FW_INSIDE$
    ip address 10.1.1.1 255.255.255.0
    ip access-group 103 in
    ip nat inside
    ip virtual-reassembly in
    ip forward-protocol nd
    ip http server
    ip http authentication local
    ip http secure-server
    ip http path flash:/gui
    ip nat inside source list 1 interface FastEthernet0/0 overload
    ip route 10.1.10.1 255.255.255.255 Integrated-Service-Engine0/0
    control-plane
    bridge 1 route ip
    bridge 100 route ip
    voice-port 0/0/0
    cptone AU
    voice-port 0/0/1
    cptone AU
    voice-port 0/0/2
    cptone AU
    voice-port 0/0/3
    cptone AU
    voice-port 0/1/0
    cptone AU
    voice-port 0/1/1
    cptone AU
    voice-port 0/2/0
    translate calling 1112
    connection plar opx 398
    description Configured by CCA 4 FXO-0/2/0-Custom-AA
    caller-id enable
    voice-port 0/2/1
    connection plar opx 398
    description Configured by CCA 4 FXO-0/2/1-Custom-AA
    caller-id enable
    voice-port 0/2/2
    connection plar opx 398
    description Configured by CCA 4 FXO-0/2/2-Custom-AA
    caller-id enable
    voice-port 0/2/3
    connection plar opx 398
    description Configured by CCA 4 FXO-0/2/3-Custom-AA
    caller-id enable
    voice-port 0/4/0
    auto-cut-through
    signal immediate
    input gain auto-control -15
    description Music On Hold Port
    sccp local Loopback0
    sccp ccm 10.1.1.1 identifier 1 version 4.0
    sccp
    sccp ccm group 1
    associate ccm 1 priority 1
    associate profile 1 register confprof1
    dspfarm profile 1 conference
    description DO NOT MODIFY, active CCA conference profile - CCA2.0 codec711
    codec g711alaw
    codec g711ulaw
    maximum conference-participants 32
    maximum sessions 2
    associate application SCCP
    dial-peer voice 2000 voip
    description ** cue voicemail pilot number **
    destination-pattern 300
    b2bua
    session protocol sipv2
    session target ipv4:10.1.10.1
    voice-class sip outbound-proxy ipv4:10.1.10.1
    dtmf-relay rtp-nte
    no vad
    dial-peer voice 2001 voip
    description ** cue auto attendant number **
    translation-profile outgoing PSTN_CallForwarding
    destination-pattern 398
    b2bua
    session protocol sipv2
    session target ipv4:10.1.10.1
    voice-class sip outbound-proxy ipv4:10.1.10.1
    dtmf-relay rtp-nte
    no vad
    dial-peer voice 2012 voip
    description ** cue prompt manager number **
    translation-profile outgoing PSTN_CallForwarding
    destination-pattern 739
    b2bua
    session protocol sipv2
    session target ipv4:10.1.10.1
    voice-class sip outbound-proxy ipv4:10.1.10.1
    dtmf-relay rtp-nte
    no vad
    dial-peer voice 90 pots
    description AU-Mobile
    preference 1
    destination-pattern 04........
    port 0/2/0
    forward-digits all
    no sip-register
    dial-peer voice 68 pots
    description NSW Number
    preference 1
    destination-pattern 02........
    port 0/2/0
    forward-digits all
    no sip-register
    dial-peer voice 69 pots
    description TAS Number
    preference 1
    destination-pattern 03........
    port 0/2/0
    forward-digits all
    no sip-register
    dial-peer voice 70 pots
    description WA-SA-NT number
    preference 1
    destination-pattern 08........
    port 0/2/0
    forward-digits all
    no sip-register
    dial-peer voice 72 pots
    description QA-number
    preference 1
    destination-pattern 07........
    port 0/2/0
    forward-digits all
    no sip-register
    dial-peer voice 74 pots
    description International number
    preference 1
    destination-pattern 0011T
    port 0/2/0
    forward-digits all
    no sip-register
    dial-peer voice 30 pots
    description Australia-1800
    preference 1
    destination-pattern 1800......
    port 0/2/0
    forward-digits all
    no sip-register
    dial-peer voice 31 pots
    description Australia-1300
    preference 1
    destination-pattern 1300......
    port 0/2/0
    forward-digits all
    no sip-register
    dial-peer voice 32 pots
    description 13 Australia
    preference 5
    destination-pattern 13....
    port 0/2/0
    forward-digits all
    dial-peer voice 67 pots
    description mel-number
    preference 1
    destination-pattern 9.......
    port 0/2/0
    forward-digits all
    no sip-register
    dial-peer voice 75 pots
    description mel-Number
    preference 1
    destination-pattern 8.......
    port 0/2/0
    forward-digits all
    no sip-register
    dial-peer voice 76 pots
    description VIC number
    preference 1
    destination-pattern 5.......
    port 0/2/0
    forward-digits all
    no sip-register
    dial-peer voice 33 pots
    description Emergency NUmber
    preference 1
    destination-pattern 0000
    port 0/2/0
    forward-digits all
    no sip-register
    no dial-peer outbound status-check pots
    telephony-service
    sdspfarm conference mute-on 111 mute-off 222
    sdspfarm units 5
    sdspfarm tag 1 confprof1
    conference hardware
    video
    max-ephones 14
    max-dn 56
    ip source-address 10.1.1.1 port 2000
    max-redirect 20
    auto assign 1 to 1 type bri
    calling-number initiator
    service phone videoCapability 1
    service phone webAccess 0
    service dnis overlay
    service dnis dir-lookup
    timeouts interdigit 7
    system message UC520
    url services http://10.1.10.1/voiceview/common/login.do
    url authentication http://10.1.10.1/CCMCIP/authenticate.asp
    load 7906 SCCP11.9-2-1S
    load 7911 SCCP11.9-2-1S
    load 7931 SCCP31.9-1-1SR1S
    load 7960-7940 P00308010200
    load 521G-524G cp524g-8-1-17
    time-zone 48
    date-format dd-mm-yy
    voicemail 300
    max-conferences 8 gain -6
    call-forward pattern .T
    call-forward system redirecting-expanded
    hunt-group logout HLog
    multicast moh 239.10.16.16 port 2000
    web admin system name cisco secret 5 $1$NPt8$6I2moMN32fQoz083VCFm90
    dn-webedit
    time-webedit
    transfer-system full-consult dss
    transfer-pattern 0.T
    transfer-pattern .T
    secondary-dialtone 0
    night-service day Sun 17:00 09:00
    night-service day Mon 17:00 09:00
    night-service day Tue 17:00 09:00
    night-service day Wed 17:00 09:00
    night-service day Thu 17:00 09:00
    night-service day Fri 17:00 09:00
    night-service day Sat 17:00 09:00
    create cnf-files version-stamp 7960 Dec 23 2013 10:55:20
    ephone-template 15
    softkeys remote-in-use Newcall
    softkeys idle Redial Newcall Cfwdall Pickup Gpickup Dnd HLog Login
    softkeys seized Cfwdall Endcall Redial Pickup Meetme Gpickup Callback
    softkeys connected Hold Endcall Trnsfer Confrn ConfList RmLstC Acct Park Select Join
    button-layout 7931 2
    ephone-template 16
    softkeys remote-in-use Newcall
    softkeys idle Redial Newcall Cfwdall Pickup Gpickup Dnd HLog Login
    softkeys seized Cfwdall Endcall Redial Pickup Meetme Gpickup Callback
    softkeys connected Hold Endcall Trnsfer Confrn ConfList RmLstC Acct Park Select Join
    ephone-template 17
    softkeys remote-in-use CBarge Newcall
    softkeys idle Redial Newcall Cfwdall Pickup Gpickup Dnd HLog Login
    softkeys seized Cfwdall Endcall Redial Pickup Meetme Gpickup Callback
    softkeys connected Hold Endcall Trnsfer Confrn ConfList RmLstC Acct Park Select Join
    ephone-template 18
    softkeys remote-in-use CBarge Newcall
    softkeys idle Redial Newcall Cfwdall Pickup Gpickup Dnd HLog Login
    softkeys seized Cfwdall Endcall Redial Pickup Meetme Gpickup Callback
    softkeys connected Hold Endcall Trnsfer Confrn ConfList RmLstC Acct Park Select Join
    button-layout 7931 2
    ephone-dn 5 dual-line
    number 301 no-reg primary
    label 301
    description PhoneA Analog
    name PhoneA Analog
    ephone-dn 6 dual-line
    number 302 no-reg primary
    label 302
    description PhoneB Analog
    name PhoneB Analog
    ephone-dn 7 dual-line
    number 303 no-reg primary
    label 303
    description PhoneC Analog
    name PhoneC Analog
    ephone-dn 8 dual-line
    number 304 no-reg primary
    label 304
    description PhoneD Analog
    name PhoneD Analog
    ephone-dn 9
    number BCD no-reg primary
    description MoH
    moh out-call ABC
    ephone-dn 10 dual-line
    number 201 no-reg primary
    pickup-group 1
    label 201
    description Extension 201
    name Receptionist Receptionist
    mobility
    call-forward busy 300
    call-forward noan 300 timeout 20
    ephone-dn 11 dual-line
    number 207 no-reg primary
    label 207
    description Extension 207
    name None None
    ephone-dn 12 dual-line
    call-waiting ring
    number 203 no-reg primary
    pickup-group 1
    label 203
    description Extension 203
    name Peter Steve
    call-forward busy 300
    call-forward noan 300 timeout 15
    huntstop channel
    ephone-dn 13 dual-line
    call-waiting ring
    number 204 no-reg primary
    pickup-group 1
    label 204
    description Extension 204
    name Tim OConnor
    call-forward busy 300
    call-forward noan 300 timeout 20
    huntstop channel
    ephone-dn 14 dual-line
    number 205 no-reg primary
    pickup-group 1
    label 205
    description 205
    name 205
    ephone-dn 15 dual-line
    number 206 no-reg primary
    pickup-group 1
    label 206
    description 206
    name 206
    ephone-dn 16 dual-line
    call-waiting ring
    number 202 no-reg primary
    pickup-group 1
    label 202
    description Extension 202
    name David Holmes
    call-forward busy 300
    call-forward noan 300 timeout 15
    huntstop channel
    ephone-dn 17 dual-line
    number 208 no-reg primary
    label 208
    description 208
    name 208
    ephone-dn 18 dual-line
    number 209 no-reg primary
    label 209
    description 209
    name 209
    ephone-dn 19 dual-line
    number 210 no-reg primary
    label 210
    description 210
    name 210
    ephone-dn 43 octo-line
    number 771 no-reg primary
    conference meetme
    preference 3
    ephone-dn 44 octo-line
    number 771 no-reg primary
    conference meetme
    preference 2
    no huntstop
    ephone-dn 45 octo-line
    number 771 no-reg primary
    conference meetme
    preference 1
    no huntstop
    ephone-dn 46 octo-line
    number 771 no-reg primary
    conference meetme
    no huntstop
    ephone-dn 49 octo-line
    number C001 no-reg primary
    conference ad-hoc
    preference 3
    ephone-dn 50 octo-line
    number C001 no-reg primary
    conference ad-hoc
    preference 2
    no huntstop
    ephone-dn 51 octo-line
    number C001 no-reg primary
    conference ad-hoc
    preference 1
    no huntstop
    ephone-dn 52 octo-line
    number C001 no-reg primary
    conference ad-hoc
    no huntstop
    ephone-dn 55
    number A801... no-reg primary
    mwi off
    ephone-dn 56
    number A800... no-reg primary
    mwi on
    ephone 1
    device-security-mode none
    mac-address 4142.4DB8.0000
    ephone-template 16
    max-calls-per-button 2
    type anl
    button 1:5
    ephone 2
    device-security-mode none
    mac-address 4142.4DB8.0001
    ephone-template 16
    max-calls-per-button 2
    type anl
    button 1:6
    ephone 3
    device-security-mode none
    mac-address 4142.4DB8.0002
    ephone-template 16
    max-calls-per-button 2
    type anl
    button 1:7
    ephone 4
    device-security-mode none
    mac-address 4142.4DB8.0003
    ephone-template 16
    max-calls-per-button 2
    type anl
    button 1:8
    ephone 5
    device-security-mode none
    mac-address 0024.97AA.E811
    ephone-template 15
    max-calls-per-button 2
    username "Receptionist" password receptionist
    type 7931
    button 1:10
    --More--                    !
    ephone 6
    device-security-mode none
    mac-address 0024.C4FC.4013
    ephone-template 16
    username "None"
    type 7911
    button 1:11
    ephone 7
    device-security-mode none
    video
    mac-address 000F.34FA.168B
    ephone-template 16
    username "steve" password petersteve
    speed-dial 1 xxx label "Peter - Home"
    speed-dial 2 xxx label "David - Mobile"
    speed-dial 3 xxx label "Tim - Mobile AUS"
    speed-dial 4 xxx label "Tim - Mobile USA"
    type 7960
    button 1:12
    ephone 8
    device-security-mode none
    video
    mac-address A40C.C394.B1F0
    ephone-template 16
    username "tim" password timoconnor
    speed-dial 1 xxx label "David - Mobile"
    speed-dial 2 xxx label "Peter - Mobile"
    speed-dial 3 xxx label "Clare - Mobile"
    type 7911
    button 1:13
    ephone 9
    device-security-mode none
    mac-address 0024.C4FC.5425
    ephone-template 16
    type 7911
    button 1:14
    ephone 10
    device-security-mode none
    mac-address 0024.C4FD.E27C
    ephone-template 16
    type 7911
    button 1:15
    ephone 11
    device-security-mode none
    video
    mac-address 0007.5098.1AB6
    ephone-template 16
    username "holmes" password davidholmes
    speed-dial 1 xx label "David - Home"
    speed-dial 2 xxxl abel "Sue - Mobile"
    speed-dial 3 xxx label "Peter - Mobile"
    speed-dial 4 xxx label "Tim - Mobile USA"
    speed-dial 5 xxx label "Tim - Mobile AUS"
    type 7960
    button 1:16
    ephone-hunt 1 sequential
    pilot 501
    list 202, 203, 204
    final 300
    timeout 8, 8, 8
    no-reg pilot
    statistics collect
    description Sales
    alias exec cca_vm_notification schedule from_time=00 to_time=24
    banner login ^CCisco Configuration Assistant. Version: 3.2 (3). Fri Nov 15 22:54:23 EST 2013^C
    line con 0
    no modem enable
    line aux 0
    line 2
    no activation-character
    no exec
    transport preferred none
    transport input all
    line vty 0 4
    transport input all
    line vty 5 100
    transport input all
    ntp master
    end
    UC520#

    I was configure custom disconnect tone refer to this site:
    http://ciscoflair.blogspot.com/2009/05/cisco-fxo-disconnect-issue.html
    And the tone is in the attachment, and the custom disconnect tone configuration like below:
    voice class custom-cptone Disconnect
    dualtone disconnect
      frequency 420 420
      cadence 251 255 245 250 249 250 250 250
    and the port configuration was like below:
    voice-port 0/1/2
    supervisory disconnect dualtone mid-call
    supervisory custom-cptone Disconnect
    cptone NL
    timeouts interdigit 4
    timeouts call-disconnect 5
    timeouts wait-release 5
    timing hookflash-out 500
    connection plar 334
    impedance complex2
    caller-id enable
    caller-id alerting line-reversal
    caller-id alerting dsp-pre-allocate
    but it was not working and the phone still ringing after the PSTN caller disconnect.
    but i was read about "dualtone-detect-params", and i was add the below command and i do not understand it, but it was solve hte problem:
    voice class dualtone-detect-params 1
    freq-max-deviation 20
    cadence-variation 50
    so what it is and how to determine this parameters.

  • Full Directory option on auto attendant consoles

    Hi All,
    I have been following the guide and there is something that isn't clear. Is the full directory setting  mapped to the ldap settings on the cucm? if i have added a local  user manually on cucm will this not show on the full directory of the auto-attendant console?
    I have already configured the settings on server to sync contacts.
    Please advise.
    Thanks

    Yes, all End Users (not Application Users) from CUCM should appear in the CUxAC directory provided that it meets any rules you have configured. By default it should pull everything over. This does not happen in realtime so you may need to force a sync, most commonly through a service restart.
    Please remember to rate helpful responses and identify helpful or correct answers.

  • Ability to dial an extension directly from dtmf Auto Attendent?

    I think i know the answer but want to make sure there is no creative workaround I'm missing. ;-)
    Is there anyway to get the ability to dial an extension (at any time) directly from dtmf Auto Attendent? (without pressing ##)
    http://windowspbx.blogspot.com

    I can confirm on our Exchange UM setup, speech enabled AA's can accept DTMF inputs when the caller hits the auto-attendant. I think the only extra thing I had to do was create a dial rule group for our extensions and allow the auto attendant to utilze
    that dial rule group: Name - Extensions Number mask - 5xxx Dialed number - 5xxx I then had to make sure the Lync front ends had appropriate normalization rules to normalize the 5xxx to the correct lineuri format (e.g.: 5xxx to +1309xxxxxx;ext=5xxx). Aside
    from that, I can also confirm that this works even if the destination extension is NOT enabled on Lync or has an Exchange UM mailbox. In that case, the call gets forwarded outside the Lync environment to your gateway for routing to wherever the gateway route
    rules indicate it should go.Trevor

  • Cisco UC560 java.lang.NullPointerException error when opening "auto attendant" CCA

    Hi Guys,
    In CCA i get the error:java.lang.NullPointerException and it is only when selecting "Auto Attendant".
    No Configuration has been done via CLI
    Cisco IOS Software, UC500 Software (UC500-ADVIPSERVICESK9-M), Version 15.1(4)M5, RELEASE SOFTWARE (fc1)
    CCA version 3.2(2)
    Attaching CCA logs
    Any Ideas ?

    I would suggest downloading the latest version of the IDE (v. 5.0) which is available at:
    http://wwws.sun.com/software/sundev/jde/index.html

  • Cisco 2801 Auto Attendant

    hello
    I have 2 Cisco 2801 running CME 4.3 and will be converter to SRST Routers, but they''ll have T1 card, because they used to has FXO card with 4 lines now they will have T1, but I wonder witch solution for auto attendant should I have for those routers especially the Unity Express.
    Thanks

    Before switching to CM, think twice, because you will gain a lot of complications, consts, and loose nice features and flexibility if you do that.

  • Auto-Attendant Not Running in UC500 Series

    Hi guys,
    I've got a little problem here. My auto-attendant couldn't run in my UC500.
    Here I give you a little command I took from my UC500:
    dial-peer voice 2003 voip
    description ** cue auto attendant PSTN number **
    translation-profile outgoing AA_Profile
    destination-pattern 57973199$
    b2bua
    voice-class sip outbound-proxy  ipv4:10.1.10.1
    session protocol sipv2
    session target ipv4:10.1.10.1
    dtmf-relay sip-notify
    codec g711ulaw
    no vad
    Please let me know if you need any more command from my UC.
    Regards,
    Denny

    updated,
    There is no information in service-module integrated-Service-Engine 0/0 status.
    I think this is the part of voicemail configuration (CMIIW)
    dial-peer voice 2000 voip
    description ** cue voicemail pilot number **
    destination-pattern 221
    b2bua
    session protocol sipv2
    session target ipv4:10.1.10.1
    dtmf-relay sip-notify
    codec g711ulaw
    no vad
    If I telnet the UC via CME, the user interface looks so simple, very2 different with the old one.
    Actually, I don't care with the voicemail, but I just care with the auto attendant. Because the ip phone cannot be dialled from outside using its direct line, but can be dialled from inside.
    I really appreciate if you can give me another advice for this one.
    Regards,
    Denny

  • Manage Auto Attendent Prompts from Outside Network

    Is it possible to manage, edit, change auto attendant prompts in CME from outside network i.e.: calling in from outside line?
    Any help would be greatly appreciated!

    Hi Dave Kallweit,
    We don't have not a option modify from prompt thru TUI :-).
    Regards,
    Mohammed Noor

  • Retrieve UM Auto Attendant configuration

    in
    this-link there are many shell commands for editing UM Auto Attendant configuration , 
    but there are no commands for retrieve the same information ... is EWS API is the answer? 
    I'm trying with C# / shell commands to get these information 
    How I  : 
    get UMAutoAttendant Business Hours ?
    get Business Hours Greeting ? 
    etc...
    for example you can change business hours schedule  , but you can't get the same data
    Set-UMAutoAttendant -Identity MyUMAutoAttendant -BusinessHoursSchedule 0.10:45-0.13:15,1.09:00-1.17:00,6.09:00-6.16:30
    I wanna retreive the same information 
    0.10:45-0.13:15,1.09:00-1.17:00,6.09:00-6.16:30
    the only thing i can get is
    [PS] C:\Windows\system32>Get-UMAutoAttendant -Identity ZakosUM
    Name UMDialPlan PilotIdentifierList SpeechEnabled Status
    ZakosUM DP {} True Enabled
    thanks

    You can execute the cmdlets from Managed code using Remote powershell
    http://msdn.microsoft.com/en-us/library/office/ff326159(v=exchg.140).aspx
    eg
    System.Security.SecureString secureString = new System.Security.SecureString();
    foreach (char c in Password)
    secureString.AppendChar(c);
    PSCredential credential = new PSCredential(AdminUserName, secureString);
    WSManConnectionInfo connectionInfo = new WSManConnectionInfo(new Uri("https://" + PSServerName), "http://schemas.microsoft.com/powershell/Microsoft.Exchange", credential);
    connectionInfo.AuthenticationMechanism = AuthenticationMechanism.Basic;
    connectionInfo.SkipCACheck = true;
    connectionInfo.SkipCNCheck = true;
    connectionInfo.MaximumConnectionRedirectionCount = 4;
    Runspace runspace = System.Management.Automation.Runspaces.RunspaceFactory.CreateRunspace(connectionInfo);
    runspace.Open();
    Pipeline plPileLine = runspace.CreatePipeline();
    Command gmUMAutoAttendant = new Command("Get-UMAutoAttendant");
    gmUMAutoAttendant.Parameters.Add("Identity", "test");
    plPileLine.Commands.Add(gmUMAutoAttendant);
    Collection<PSObject> RsResultsresults = plPileLine.Invoke();
    foreach (PSObject obj in RsResultsresults)
    PSObject bhs = (PSObject)obj.Properties["BusinessHoursSchedule"].Value;
    ArrayList bhsObj = (ArrayList)bhs.BaseObject;
    foreach(String Element in bhsObj){
    Console.WriteLine(Element);
    plPileLine.Stop();
    Cheers
    Glen

Maybe you are looking for

  • Newpc, new itunes, old ipod, new troubles

    Got a new pc, and installed new itunes, and now itunes does display my ipod, but not my playlists. New playlists and new music do not download to ipod. Have tried reset, redownload, reviewed cables, etc. Do not wish to try restore ipod, but will if n

  • I wanted to know if i might be eligible to recycle my ipod and get money for it?

    it is an 4g ipod nano and it works pefectly except it has scratches on the back, so i was wondering if there was any possible way i could get money for it?

  • Sales data in SAP

    Hi All, Is there any possibility to capture the sames taregt if an employee in PA30 infotypes. Regards, Bharath

  • Can interactive report have 2 "special" columns?

    I have an interactive report on which I have placed a column for redirecting to a detail form. But I want to, also, put a column that will contain a button which will perform an action (update 2 columns in db). This way if the user wants to close the

  • Custom tag as performance hits.

              Hi All,           I want to know if there is a correlation between the number of custom tags used in           a JSP page and the page's performance.           Is there a guideline/study which indicates (or otherwise) that increasing the nu