Remove IPX in CATOS
Hello,
Need help with removing IPX config from 6500 runing CATOS, all examples show adding commands but not how to remove.
These are the commands I need to remove:
set mls agingtime ipx 32
set port protocol 2/1-8 ipx on
set port name 2/8 lab-ipx
Thanks
You might try the clear command and see if it removes the commands.
HTH
Rick
Similar Messages
-
Imaging slow after removing IPX
We are running Zenworks 6.5. We basically use the imaging piece and NAL. We
removed IPX from this server this morning and now Imaging is moving at a
crawl. I'm not sure if this is related as I thought imaging was using IP.
Any ideas on what I can look at to troubleshoot this? I am making sure the
duplex settings on the switch are not mis-matched with the settings on the
NIC, but if that was the problem we should have seen this issue before
today. Any ideas would be appreciated.Disregard..... Duplex settings were splooged....all is well now.
"SRL" <[email protected]> wrote in message
news:dbE2i.2455$[email protected]..
> We are running Zenworks 6.5. We basically use the imaging piece and NAL.
> We removed IPX from this server this morning and now Imaging is moving at
> a crawl. I'm not sure if this is related as I thought imaging was using
> IP. Any ideas on what I can look at to troubleshoot this? I am making sure
> the duplex settings on the switch are not mis-matched with the settings on
> the NIC, but if that was the problem we should have seen this issue before
> today. Any ideas would be appreciated.
> -
I have removed IPX from my network and for purposes of ghosting
workstations, I still have to use dos boot disks.
I have made a custom DOS client32 disk based off the 2.7x dos client32 (NLM
disk) which works fine for most PC's, but there are some instances where I
have to use a VLM based bootdisk. I have made a vlm disk and it gets on the
network just fine, I can ping my servers by name, but I am unable to attach
to them. In the NLM disk, there is SERVLOC which I assume helps this
process, but is there a VLM component that will do the same feature, or do
I need something specific in there so it will find the server via SLP??
I know this is ancient stuff and technically unsupported, but I am looking
for some guidance.
thanks,[email protected] wrote:
> ...but there are some instances where I have to use a VLM
> based bootdisk. I have made a vlm disk and it gets on the
> network just fine, I can ping my servers by name, but I am
> unable to attach to them.
The VLM client never knew how to make NCP connections over IP. There
is an IP stack that is compatible with the VLM client, to be sure, but
that's purely as a transport protocol and not that the VLM NCP client
knew how to use it for NCP connections.
To make an IP connection you'll have to use CLIENT32.NLM & TCPIP.NLM
(the DOS/Win 2.71 client). More specifically, use the IP Server
Connection files available from support.novell.com
(http://support.novell.com/cgi-bin/se...i?/2963117.htm),
or one of the many CLIENT32.NLM-based boot disks available on
CoolSolutions and elsewhere. (Using the literal DOS/Win 2.71 files is
somewhat out of date.)
Just a personal plug, I find the TCPIP NCP connection from a
CLIENT32.NLM boot disk too unreliable for Ghost, specifically in the
"push" (image creation) direction. The TCPIP.NLM stack seems to have
bugs in that direction that get exposed by pushing a large amount of
data up to the server, as opposed to downloading. I leave IPX enabled
for my Ghost boot disks for that reason alone, even though none of my
workstations actually have or use IPX. Your mileage may vary.
Alan Adams
[email protected]
(for email, remove the crumbs) -
I understand the Client 2 isn't supported with NW 5.0 or earlier. However, is that not supported, as in "doesn't work and can't be made to", or "don't call us if you have problems"?
If it's "doesn't work", does anyone know the technical reason why not?
Thank you in advance!
-BenAnders Gustafsson wrote:
> The core reason is that versions earlier than 5.0 do not support NCP
> over IP and more recent versions of Windows do not come with an IPX
> stack.
Correct. To add just a bit, Client 2 was designed for Vista and later
(currently support Windows 7 and later). Microsoft removed IPX in
Vista which is why for the most part you can't use Client 2 in order to
connect to anything earlier than NW 5.0.
That being said, there used to be a gateway or migration agent as I
recall (scmd) that would allow NCP to travel across different parts of
the network that were IPX-only or IP-only, as long as scmd was running
on a NetWare server running both. It *might* be possible to get Client
2 to talk to older servers using this, but it's a stretch and
definitely wouldn't be supported.
Your world is on the move. http://www.novell.com/mobility/
Supercharge your IT knowledge. http://www.novell.com/techtalks/ -
Remove trunking from a port in catos?
All,
Simple question: I want to remove all trunking from a port on a switch running catos. Clear Trunk seemed the obvious option, though it seems to just remove the vlans that are allowed to pass over the trunk port. Set Trunk mod/port Off doesn't do the trick either. Any thoughts?
thanks!Hi Chris,
"set trunk x/y off" is the correct syntax. When you try that, what happens?
HTH,
Bobby -
Remove SNMP trap receiver in CatOS
I've done the Cisco search and came up empty. I used to know this. Isn't there a hidden remove command? Version is CatOs 8.4.1. Hopefully one of you can save the day. TIA!
How about:
clear snmp trap all
or
clear snmp trap -
CatOS: Remove a etherchannel config
Hi,
I have a 6509 running CatOS 6.4. I want to remove those unnecessary port channel configuration entries from the configuration file or set them to default, so those entries wont show up in my configure file. Especially there are some port channel configure entries having only one port in it. It doesnt make sense to have the port channel configure staying there.
I know its easy in IOS. However in CatOS, I couldnt achieve this goal. Setting port channel mode to off wont help. I dont want to delete the port channel entry from the configure file then upload again. Are there any other commands I could use to achieve this? Any comments are welcomed!
Thanks,
KenHi Ken,
Unfortunately, there is no elegant way to remove the superfluous 'set port channel' commands from the
config, so better leave it in.
If you really want to remove these unused port channels, you'll have to clear the config for the module, which is like trying to kill ants with a machine gun... :-)
HTH,
Bobby -
CatOS and removing a vlan from its VTP server..
Hi guys
Question I hope can be cleared up very quickly.
I have a pair of old switches running CatOS, these are also VTP servers for the network running off em..
I need to de-comission a Vlan but cannot figure out the best way to remove the vlan from them?
Obviously,
IOS I would just
conf t
no vlan xx
end
But I cannot for the life of me find the best way to do this on CatOS...
Ive found that it may be a "clear vlan xx" command, but not sure..
Any ideas?
Thanks,
-Graham
Please note: My comments are simply suggestions. I cannot be held liable for any loss of data, life or marbles due to following my instructions.
Technical Design Engineer
IMsupporting.com - Live chat softwareDoesnt that just remove the vlan from the port?
Ideally I want to remove the vlan completely from the system? ( Its a VTP server too )
Ie:
conf t
no vlan xx
end
Would do it on cisco IOS..
would
conf t
clear vlan xx
end
do it on catos?
Thanks
Graham -
Convert Qos commands from CATOS to IOS
Hello,
i've some problems converting some Qos commands from CATos to IOS can anybody help me?
set qos drop-threshold 1q4t rx queue 1 50 60 80 100
set qos map 2q2t tx 1 1 cos 0
set qos map 1p1q4t rx 1 3 cos 4
set qos wrr 1p2q2t 50 255
set qos txq-ratio 1p2q2t 70 15 15
set qos wred 1p2q2t tx queue 1 70:100 70:100
set qos bridged-microflow-policing disable 1,50-54,100-121,500,700-702,1006-1011,1016
set qos policed-dscp-map 1:1
set qos policed-dscp-map excess-rate 0:0
set qos acl default-action ip dscp 0
set qos acl default-action ipx
set qos acl default-action mac
set qos policy-source local
set qos rsvp disable
set qos rsvp policy-timeout 30
set qos rsvp local-policy forward
!Module with GE interfaces
set port qos 3/1-16 cos 0
set port qos 3/1-16 trust trust-cos
set port qos 3/1-16 port-based
set port qos 3/1-16 policy-source local
set qos statistics export port 3/1 disable
set qos statistics export port 3/2 disable
set qos statistics export port 3/3 disable
set qos statistics export port 3/4 disable
set qos statistics export port 3/5 disable
set qos statistics export port 3/6 disable
set qos statistics export port 3/7 disable
set qos statistics export port 3/8 disable
set qos statistics export port 3/9 disable
set qos statistics export port 3/10 disable
set qos statistics export port 3/11 disable
set qos statistics export port 3/12 disable
set qos statistics export port 3/13 disable
set qos statistics export port 3/14 disable
set qos statistics export port 3/15 disable
set qos statistics export port 3/16 disableThis URL should help you:
http://www.cisco.com/warp/public/473/73.html -
Changing VTP Setting and VLANs on CatOS
Greetings to all...
I'm working replacing our old 5505 Core switches running CatOS with 6509s running IOS with a new VLAN structure (VLAN 100 (5505) will be 400 (6509)). The down stream switches are 2948s running CatOS.
My problem is that everytime I either change SC0 or port 2/1 to the new VLAN, I lose my connectivity. Anyone know of a hot command that will change both at the same time?
Thanks,
TomDo I understand that port 2/1 is the uplink port? If so, it should not be difficult. It is not necessary for the management and the trunk native VLAN to be the same, so your should be able to do them in sequence. In fact, I have just changed the management VLAN of our 20 Cat4000 CatOS switches remotely without any problem.
However, you will get cut off at the moment that you change the SC0, but this has nothing to do with the port 2/1 (assuming that the trunk is carrying both old and new management VLANs).
The way I did it was to start with the management station and all the switches on the old management VLAN. On your router (or L3 switch), create the new management VLAN, give its L3 interface a junk IP address, and enable ip proxy-arp on both old and new management VLANs. Note that the router is still routing the old management subnet, say 192.168.2.0/24, to the old management VLAN.
Now pick on an address which will be the router's IP address on the new management VLAN, say 192.168.2.254. Go into your access switch, and configure that address as the default gateway, set ip route default 192.168.2.254. Then reconfigure the SC0 interface to its new VLAN. At that point, your telnet session will get cut off because the management function of the 2948 is on the new VLAN. So, go to your router at set a host route for the access switch to the new VLAN, ip route 192.168.2.2 255.255.255.255 VLAN400. You should now be able telnet to the switch from your management station. Packets from the management station to the switch will be routed by the host route. Packets from the switch to the management station will be routed courtesy of the proxy-arp.
Repeat this for each access switch, and once they are all done you can move your management station and give the router its proper address 192.168.2.254 on the new VLAN. You can then remove the proxy ARP and/or change the native VLAN of the trunks at your leisure. If you are changing the native VLAN of the trunks, do the remote end first ;-).
Hope I have understood your question correctly, and hope this helps.
Kevin Dorrell
Luxembourg -
Cisco 6506 CatOS unable to bootup
Hi,
I have a 6506 with SUP1, no MSFC running CatOS.
Module 1: Removed
Module 2: WS-X6K-SUP1A-2GE
Module 3: WS-X6348
Module 4: WS-X6348
Module 5: WS-X6408A-GBIC
Module 6: WS-X6408A-GBIC
However, it doesn't seems to be able to bootup properly.
Could this be an hardware issue?
What should I do?
System Bootstrap, Version 5.3(1)
Copyright (c) 1994-1999 by cisco Systems, Inc.
c6k_sup1 processor with 65536 Kbytes of main memory
Autoboot executing command: "boot bootflash:cat6000-sup.5-5-1.bin"
Uncompressing file: ###########################################################
System Power On Diagnostics
DRAM Size ....................64 MB
Testing DRAM..................Passed
Verifying Text Segment .......Passed
NVRAM Size ...................512 KB
Saving NVRAM .................Done
Testing NVRAM ................Passed
Restoring NVRAM ..............Done
Level2 Cache .................Present
Testing Level2 Cache .........Passed
System Power On Diagnostics Complete
Boot image: bootflash:cat6000-sup.5-5-1.bin
=====Stopped Moving Here=====Brought the modules to a reseller.
Put it in their chassis... and it runs...
Console> (enable) sh ver
WS-C6506 Software, Version NmpSW: 5.5(1)
Copyright (c) 1995-2000 by Cisco Systems
NMP S/W compiled on Jun 8 2000, 21:09:45
System Bootstrap Version: 5.3(1)
Hardware Version: 3.0 Model: WS-C6506 Serial #: TBA05060101
Mod Port Model Serial # Versions
1 2 WS-X6K-SUP1A-2GE SAD04210EJD Hw : 3.1
Fw : 5.3(1)
Fw1: 5.1(1)CSX
Sw : 5.5(1)
Sw1: 5.5(1)
L3 Switching Engine SAD042305R2 Hw : 1.1
3 48 WS-X6348-RJ-45 SAD04250LF3 Hw : 1.1
Fw : 5.3(1)
Sw : 5.5(1)
5 48 WS-X6348-RJ-45 SAD041809EF Hw : 1.1
Fw : 5.3(1)
Sw : 5.5(1)
DRAM FLASH NVRAM
Module Total Used Free Total Used Free Total Used Free
1 65408K 37935K 27473K 16384K 6925K 9459K 512K 201K 311K
Uptime is 0 day, 0 hour, 3 minutes
Console> (enable) sh mod
Mod Slot Ports Module-Type Model Sub Status
1 1 2 1000BaseX Supervisor WS-X6K-SUP1A-2GE yes ok
3 3 48 10/100BaseTX Ethernet WS-X6348-RJ-45 no ok
5 5 48 10/100BaseTX Ethernet WS-X6348-RJ-45 no ok
Mod Module-Name Serial-Num
1 SAD04210EJD
3 SAD04250LF3
5 SAD041809EF
Mod MAC-Address(es) Hw Fw Sw
1 00-30-19-d8-eb-96 to 00-30-19-d8-eb-97 3.1 5.3(1) 5.5(1)
00-30-19-d8-eb-94 to 00-30-19-d8-eb-95
00-05-00-ac-cc-00 to 00-05-00-ac-cf-ff
3 00-b0-c2-f6-65-bc to 00-b0-c2-f6-65-eb 1.1 5.3(1) 5.5(1)
5 00-01-97-0e-27-f0 to 00-01-97-0e-28-1f 1.1 5.3(1) 5.5(1)
Mod Sub-Type Sub-Model Sub-Serial Sub-Hw
1 L3 Switching Engine WS-F6K-PFC SAD042305R2 1.1
So the problem is either "me", or the chassis backplane.
Gonna bring the Chassis down for a check, just to be sure. -
Ill have the same truble whit my network!
do you fidind out some thing about it?
Ill wold be wery grateful if you please could help me.
Patrik
Old Mess
I am trying to load a wireless notebook adapter onto Microsoft ME. I get
and error message: "File not found: ipx.msg" "looking for The Novell
Client for Windows 95/98 CD". The notebook adapter will not load. The
NetWare Client is not available in the "remove programs" icon on the
control panel. The Technical Information Document 10013922 did not apply
100% and did not work. Any suggestions how to remove Novell Client
3.21.0.0 OR bypass this problem.P,
It appears that in the past few days you have not received a response to your posting. That concerns us, and has triggered this automated reply.
Has your problem been resolved? If not, you might try one of the following options:
- Do a search of our knowledgebase at http://support.novell.com/search/kb_index.jsp
- Check all of the other support tools and options available at http://support.novell.com in both the "free product support" and "paid product support" drop down boxes.
- You could also try posting your message again. Make sure it is posted in the correct newsgroup. (http://support.novell.com/forums)
If this is a reply to a duplicate posting, please ignore and accept our apologies and rest assured we will issue a stern reprimand to our posting bot.
Good luck!
Your Novell Product Support Forums Team
http://support.novell.com/forums/ -
8/29/2014 7:15am
It seems to me that if Microsoft's platform can not fix it with the troubleshooter that the troubleshooter sucks. It does not know when errors are thrown so your developer sucks on creating software for errors that are popping up in your software?
if a error is thrown in Windows 8 it should catch it upon a thrown error in programming? This hsould be a level 1 ticket. Since when I call you support for error in your product no one wants to address problems in your software and get mea tech to resolve
it?
The question now is how do I fix this and why is it causing me an internal error 500 for my web server install?
I may have other issues but I need access to my web server through my browser I used fsocketopen to troubleshoot it?
It gets back a internal 500 on Gecko process in firefox and on IE it just won't serve out the document in my web server abyss or apache? So the question is what service is broken so I can't serve my [web server] pages out? Let me go through all the event
logs that I have with errors below?
Under Applications:
1) Failure to load the application settings for package microsoft.windowscommunicationsapps_8wekyb3d8bbwe. Error Code: 10
2) LMS Service cannot connect to Intel(R) MEI driver. Error level 1
3) Failure to load the application settings for package microsoft.windowscommunicationsapps_8wekyb3d8bbwe. Error Code: 3
4) SearchIndexer (3476) Windows: The database engine attached a database (1, C:\ProgramData\Microsoft\Search\Data\Applications\Windows\Windows.edb). (Time=0 seconds)
5) Internal Timing Sequence: [1] 0.000, [2] 0.000, [3] 0.125, [4] 0.000, [5] 0.000, [6] 0.000, [7] 0.000, [8] 0.000, [9] 0.000, [10] 0.000, [11] 0.000, [12] 0.000.
Saved Cache: 1 0: Evenet Id level 326.
6) SearchIndexer (3476) Windows: The database engine started a new instance (0). (Time=0 seconds)
7) Internal Timing Sequence: [1] 0.000, [2] 0.000, [3] 0.000, [4] 0.000, [5] 0.000, [6] 0.000, [7] 0.000, [8] 0.000, [9] 0.000, [10] 0.000. eveent level 105
8) SearchIndexer (3476) Windows: The database engine (6.03.9600.0000) is starting a new instance (0). Error Level 102
Under Security:
1) We might want to check this out here User Account Management changed?
Under Setup: no errors.
Under System below:
1) Name resolution for the name win8.ipv6.microsoft.com. timed out after none of the configured DNS servers responded.Event level 1014
2) Intel(R) 82567LM-3 Gigabit Network Connection
Network link is disconnected.
3) The system has returned from a low power state.
Sleep Time: 2014-08-29T05:10:07.602701000Z
Wake Time: 2014-08-29T13:13:47.945773100Z
Wake Source: Device -USB Root Hub : Error level 1
4) The browser has forced an election on network \Device\NetBT_Tcpip_{58565081-3013-43B6-AE07-CC89C71F6036} because a master browser was stopped. Event Id 8033.
5) The driver \Driver\WudfRd failed to load for the device SWD\WPDBUSENUM\_??_USBSTOR#Disk&Ven_EPSON&Prod_Storage&Rev_1.00#7&2d369789&0&533536503532383375&0#{53f56307-b6bf-11d0-94f2-00a0c91efb8b}. Event error 219.
6) The driver \Driver\WudfRd failed to load for the device SWD\WPDBUSENUM\{3c83e4cf-28e9-11e4-827b-b8ac6f8aec21}#0000000000004000. Error Level Id 219.
7) The UMDF reflector was unable to complete startup because the WUDFPf service was not found. This service may be started later during boot, at which point Windows will attempt to start the device again. Error Id 10114.
8) Unable to bind to the underlying transport for [::]:80. The IP Listen-Only list may contain a reference to an interface which may not exist on this machine. The data field contains the error number. Event Id 15005.
9) The supersafer64 service failed to start due to the following error:
The system cannot find the file specified. Event ID 7000.
10) The SNMP Service encountered an error while accessing the registry key SYSTEM\CurrentControlSet\Services\SNMP\Parameters\TrapConfiguration. Error: 1500.
11) The SAS Core Service service failed to start due to the following error:
The system cannot find the file specified. 7000
12 The World Wide Web Publishing Service (WWW Service) did not register the URL prefix http://*:80/ for site 1. The site has been disabled. The data field contains the error number. 1004
13) The driver \Driver\WudfRd failed to load for the device SWD\WPDBUSENUM\_??_USBSTOR#Disk&Ven_EPSON&Prod_Storage&Rev_1.00#7&2d369789&0&533536503532383375&0#{53f56307-b6bf-11d0-94f2-00a0c91efb8b}. Error level 219
14) Name resolution for the name win8.ipv6.microsoft.com. timed out after none of the configured DNS servers responded. Error level 1014.
Now I need help with all these error since Windows 8 with maybe 15 applications is failing after no setup errors? What would cause these we need to find out? Since I can not use your product with so many developer errors? and to put out a products that doesn
work is pointless? So please call me and have some help me through the errors and tell your support to stop ignoring the errors that broke the products?
Sincerely, William Dunlap {removed} N. Academy blvd, 201, Colorado Springs, CO 80910 http:\\interfacesone.fnhost.org
{removed}. I need a tech to help me get my web server up?So now you don't release the security breaches in windows 8. You mean to tell me that you can use Powershell - Using WMI to breach security in VB apps on the web by getting my file structures?
What is this all about?
1 Set VPN NIC Settings
2 Get Network Data from servers
Set VPN NIC Settings
$error.clear | out-null
cls
$ErrorActionPreference = "SilentlyContinue"
if ( $Args.Count -ne 1 ) { "
Not enough arguments
Usage :
script.ps1 server
"; exit }
$server = $Args[0].ToLower()
"We are working with $server"
$netAdapt = get-wmiobject -class Win32_NetworkAdapter -computer $server
if (!($netAdapt)) {
"Failed to connect to the target server!"
exit(5)
foreach ($card in $netAdapt) {
IF (!([string]::IsNullOrEmpty($card.NetConnectionID))) {
if ($card.NetConnectionID.CompareTo("VPN Virtual NIC") -eq 0) {
$myID = $card.DeviceID
$NAC = [wmi]"\\$server\root\cimv2:Win32_NetworkAdapterConfiguration.index='$myid'"
$guid=$NAC.settingID
"Setting DNS Toggles"
$dnsToggle = $NAC.SetDynamicDNSRegistration(0,0)
if ($dnsToggle) {
"Success"
} else {
"Failure"
$strShowNicKeyName = "SYSTEM\CurrentControlSet\Control\Network\{4D36E972-E325-11CE-BFC1-08002BE10318}\$guid\connection"
#$strShowNicKeyName
$reg = [Microsoft.Win32.RegistryKey]::OpenRemoteBaseKey('LocalMachine', $server)
$regKey= $reg.OpenSubKey("$strShowNicKeyName",$true)
$showIcon = $regKey.GetValue("ShowIcon")
if (!($showIcon -eq 1)) {
"The icon is hidden.. Setting it now"
$setIcon = $regKey.SetValue('ShowIcon',1,'DWORD')
} else {
"The icon is visible already."
"Script Ends"
Get Network Data from servers
$myfile = get-content servers.txt
echo "Server IPs Subnet GW" | out-file "Results.txt" -Append
foreach ($server in $myfile) {
Write-Host "Looking at $server"
$colitems = Get-WmiObject win32_NetworkAdapterConfiguration -computer "$server" -Filter 'IPEnabled = "True"' | select ipaddress,ipsubnet,index,defaultipgateway
foreach($objItem in $colItems) {
Write-Host ""
$myip = $objItem.IPAddress -join " "
$mySubnet = $objItem.IPSubnet
$myGW = $objItem.DefaultIPGateway
$temp = $objItem.index
$myid = Get-WmiObject win32_NetworkAdapter -computer "$server" -Filter "index = $temp" | select netconnectionid
$myid = $myid -replace "@{netconnectionid=",""
$myid = $myid -Replace "}",""
echo "$server $myip $mySubnet $myGW $myid"
echo "$server $myip $mySubnet $myGW $myid" | out-file "Results.txt" -Append
Is this possible on any machine with power shell and if so how is access done?
William Dunlap -
Creating a backup of functional drive removed from broken laptop
I have a new Macbook Pro running Mountain Lion that is damaged and won't turn on. I have the drive removed and can access it using a docking station attached to my iMac running 10.6.
What is the simplest way to backup the data from this drive so that after the laptop is repaired I can return my data to the Macbook Pro?Using Disk Utility to clone a drive will automatically erase the Destination drive if it isn't already erased. To backup to a drive with stuff already on it you would need to use a backup utility like one of these:
Suggested Backup Software
1. Carbon Copy Cloner
2. Data Backup
3. Deja Vu
4. SuperDuper!
5. Synk Pro
6. Tri-Backup
Others may be found at VersionTracker or MacUpdate.
Visit The XLab FAQs and read the FAQ on backup and restore. Also read How to Back Up and Restore Your Files.
Be sure the backup utility is NOT configured to erase all files on the destination that are not on the source. If there are files identical to those already on the drive, then they will be overwritten. -
My 5th gen iPod touh was stolen a month ago. I immediately removed that device from my account and yet today I looked at my photostream and there are tons of pics of these people on my photostream. How do I get this to stop?!?
Change your iCloud ID password: http://support.apple.com/kb/HT5624. After doing so, go to Settings>iCloud, tap Delete Account, then sign back in with the new password.
Maybe you are looking for
-
Does anyone know how to publish a calendar for others to use in iCal? I was looking for a Calendar myself, but couldn't find it, so I decided to create it myself. Now I would like to publish it so that other iCal users can subscribe to it. Is this so
-
Webservice to JDBC BPM scenario
Hi Experts, I have created the below objects for the Webservice to JDBC BPM scenario. Data Type 1. DT_SOAPRequest 2. DT_SOAPResponse 3. DT_JDBCRequest 4. DT_JDBCResponse MessageType 1. MT_SOAPRequest 2. MT_SOAPResponse 3. MT_JDBCRequest 4. MT_JDBCRes
-
I have just finished downloading Version 4. Switched off the computer. Started again by clicking on the shortcut icon. Somewhat bland screen appear, just giving a bar for search. When a search is typed in and 'search' button clicked, there is no resp
-
Using Senuti: How to change iPod back from manual?
I have a iPod mini and gonna buy a Classic this weekend. I have set my iPod mini to manually. But because of this my songs don't appear in the iTunes library but only in the iTunes music folder when my iPod is connected to the computer. I have downlo
-
I'm getting an exception when performing a partial update. I'm using Endeca 6.1.1. The logging says: 'Utility 'wget_-http-127-0-0-1-9005-admin-op-update-' failed.'. I have verified that wget.exe is present. The exact logging is added below. I appreci