Removing shadows from charts (both column AND pie)

I can see there is a ShadowBoxItemRenderer (that I have no
idea from the help docs HOW to actaully implement to turn off
shadows) hoever - when/if this works - it only works on my column
chart? How can I turn off this nasty drop shadow beneath my pie
charts? Its very confusing.

Hi Tammy,
I didn't regard #2 as bug - in fact I thought it was helpful to be able to set the size to zero as a workaround to the problem outlined in #1.
Regarding #3, if this is by design, then I'd suggest that it's a poor design choice to have checkboxes next to both titles and subtitles, since this implies that they should be able to be separately controlled.   
Something else I've noticed with this formatting area is that the position and offset controls are disabled, and there doesn't appear to be any way to use them.  It would be very helpful to be able to use these to move the position of chart titles.  In a dashboard I'm currently building, we have a large stack of charts sized very small, to attempt to resemble the 'sparkline' concept.  But the chart titles are so high, it's not clear which chart they refer to (they look like they might refer to the chart above it).   As a result, I've had to remove the chart titles and place independent labels over top of each chart to be able to position them closer to the chart's display area.
Peter

Similar Messages

  • How to remove shadows from pictures

    Hello,
    I`m new to this forum and also i have no knowledge about photoshop.
    My question is how can I remove shadows from the pictures ?
    Thanks in advantage

    There are a number of ways to manipulate images to lessen the effects of shadows, ranging from doing something like Image - Adjust - Shadows/Highlights to selecting specific parts and doing spot editing.
    Can you please be more specific about what it is you want to do?  Maybe post a small sample image here (using the little camera icon just above where you type) showing the shadows you'd like to remove.
    -Noel

  • How can I remove iCloud from my Mac Book and iPad and Mac Book Air and then just reload back on the MB Air and iPad only?

    How can I remove iCloud from my Mac Book and iPad and Mac Book Air and then just reload back on the MB Air and iPad only, which have a different user with a separate Apple ID?

    You have quite muddied up the waters, I'm afraid. Assuming you now have a single GUID partition formatted Mac OS Extended, Journaled, you should try reinstalling Lion:
    Reinstalling Lion/Mountain Lion Without Erasing the Drive
    Boot to the Recovery HD: Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
    Repair the Hard Drive and Permissions: Upon startup select Disk Utility from the main menu. Repair the Hard Drive and Permissions as follows.
    When the recovery menu appears select Disk Utility. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list.  In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive.  If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the main menu.
    Reinstall Lion/Mountain Lion: Select Reinstall Lion/Mountain Lion and click on the Continue button.
    Note: You will need an active Internet connection. I suggest using Ethernet if possible because it is three times faster than wireless.

  • How do I remove Netflix from my Apple account and stop billng for it?

    How to remove Netflix from my Apple account and stop all future billing for it?

    Purchasing and managing auto-renewing subscriptions -
    http://support.apple.com/kb/HT4098

  • Business Graphics - Chart Type - Columns, and Simple Scatter Type

    Hi,
        I am interested to know more about Business Graphics Specially Chart types Columns and
    Scatter type ( and Time Scatter).  I am facing problem in producing X and Y Co-ordinate values for Charts. (Specially Date Values in X Axis.). I tried with Time Scatter type and need more documents.
    Expecting Good Documents and suggestions.
    Thanks, 
             Vinod V

    Hi
    Check this link
    http://help.sap.com/saphelp_nwmobile71/helpdata/en/86/243f403f0a9354e10000000a155106/frameset.htm
    http://help.sap.com/saphelp_nwmobile71/helpdata/en/0b/79553b066d9414e10000000a114084/frameset.htm
    https://help.sap.com/saphelp_nw04/helpdata/en/0c/95c83956852b51e10000000a114084/frameset.htm
    thanks

  • Chart missing Columns and Lines

    I have created a Column Line Chart and allow the user to input different values that change formulas to produce the columns and line on the graph. I can see the graph perfectly fine with all columns and the line on the canvas view. Whenever I try to export to any file type, upon opening the file, all but two of the columns are missing and the line is missing in all spots except for at two points.
    I've noticed that if I remove my formulas from my spreadsheet and just put in hard coded values in place of the formulas, the report populates correctly, but this takes away all functionality of allowing the user to adjust inputs, which is the entire reason we are using this software.
    Please advise how I can fix this issue so that my chart shows all data.
    Thanks,
    Dan

    Hi Dan
    This is common - this can happen due to possible reasons like
    1) The data in preview mode on which the formula is applied is not same as the hard coded or the one in design mode. So when you go to preview its different view in the chart
    2) Some other component is messing with the excel ranges you are using for formula for the chart - some components which can drop values as per their destination property.
    This is how you need to test
    - Add a test spreadsheet table component ( from selector category) and map all the cells that's included in the formula - the original range, the input values from the user interaction, and the final ranges with formula and the range to which chart is mapped to if different from the formula range.
    - Preview the dashboard and see whats going on in those cells and if they all are behaving as expected.
    - if the original data range and the input data are what you anticipate and not changed by any other variable you are not considering.
    Use more than one spreadsheet table if the ranges I suggested are not contiguous.
    Please try the above and post the updates.
    Thanks
    Runali

  • HELP! I need to be able to remove power from a PXI chassis and replace a card without rebooting the whole system

    I do not have particulars on the controller, but I am sure it's an NI chassis
    and NI regular controller that has a serial cable leading back to the PC.
    I am making this PXI rack into a debug rack for instrument cards,
    so I need to be able to remove power from just the PXI chassis
    and then replace the card with another one
    or the same one and then turn the power back on and restart a
    diagnostic test on the card WITHOUT
    having to reboot the PC.
    Is there a PCIe bridge setup that would allow me to do this?
    Is there software that I need that can accomplish this?

    Yes
    The Chassi is a NI PXI 1045
    and the controller is a NI-PXI-8331
    Let me re-enumerate my requirements:
    Background:
    I have a number of NI cards as well as other manufactured cards in the system.
    One of these cards in the NI system is considered to be a UUT.
    That is, I am using the NI card cage system and other cards in the system to test a CARD
    during a manufacturing test of said UUT CARD.
    The UUT uses a PLX 9030 for it's PCI interfacing.
    This UUT is not designed for hot swap, and I do not bieleve it is plug and play.
    Requirement:
    1. I need to be able to shut off the chassis and remove the UUT when the test finishes, replace the tested UUT
    with a unknown UUT, re-apply power and then test the new UUT WITHOUT having to reboot the PC.
    I have tried several things, such as disabling the PCIe busses in the windows control panel, and then removing power
    replacing the UUT with the next one, re-applying chassis power and then re-enabling the bus and SOMETIMES it works.
    I need a very robust way to do this.
    I also bought a CHROMA PXI-52906-E extender card with bus switches on it, so that I can remove power to the UUT
    without shutting off the chassis. The card is supposedley designed so that when power is re-applied to the UUT, the necessary
    signals to boot the PXI PCI interface is conducted, but I think something else has to be written to the card's PCI registers.
    I am by no means an expert in PCI/PXI, 
    but I seem to have exhausted all of my reserach online in how to meet my requirements.
    Perhaps there is a way for the NI8331 controller to capture PCI configuration data to the card's on system boot,
    and then "replay it" to my UUT after I re-apply power to the UUT?
    Or perhaps PLX makes such a tool?
    Any ideas?

  • How can I remove books from my Ipad "Kindle" and put them back into Icloud "archieve"

    I have purchased a mini Ipad and loaded up Kindle.  How can I remove the books I've read from my device and move them back to Icloud archieve?

    The following info is included with the current version for the Kindle app.
    Cloud shows all items in your Kindle library.
    Device shows items you have downloaded.
    Tap an item to download it from the cloud.
    Press and hold an item to remove it from your device.

  • How can I create 25 charts on a page, each chart 2 columns and 10 rows

    I need to create a chart that has 25 tables. 5 tables in 5 columns. Each table has 2 columns and 10 rows. I know it can fit all on 1 page as I have seen it done but I can not figure out how

    I had some initial difficulty understanding your question. In Numbers, a "chart" is a graph.
    You want to create a 5 x 5 array of tables, each with two columns and 10 rows, placed on a single page.
    At the default size, each cell on a new Table is 1 inch wide and 0.2 inches high. So without displaying a title, each of your 25 charts would occupy a two inch square space.
    Butted closely together, that's a space that is 10 inches wide by 10 inches high.
    On a machine set to US localization,the default page size is US Letter, placed in Landscape orientation. Left, right and top margins are set to 0.75", bottom margin is 0.5", and there is a 0.25" height reserved for page header and page footer.
    That leaves a working space that's 9.5" wide and 6.75" high.
    Obviously, some adjustments will be needed.
    0.2" is pretty much the minimum for row height. You can go smaller by typing in a smaller height in the Table Inspector, but even with 9 point type, you begin to lose the descenders on ps and qs. Go with 0.2, then use the slider in Print view to further shrink the content.
    If you can narrow the columns significantly (to 0.75" or less), then go to Page setup and change to Portrait orientation.
    In the Sheet Inspector, decrease all margins to 0.5", and the header and footer spaces to 0. Set page orientation to Portrait.
    Now consider the Table(s). If you've opened a new, blank document, you'll have a multi column, multi row table with one header row and one header column. If you don't need the header row and header column, delete them (column A, Row 1) right away.
    Reduce the number of rows to 10 and the number of columns to 2. Select the whole table and, in the Table inspector, set the row height to 0.16" and the row width to 0.73".
    With the table still selected. press command-D four times to create four duplicate tables.
    Go View > Show Rulers, then View > Show Print View. go back to the Table Inspector and use the slider to set Content Scale to about 94%.
    Drag the still selected Table to the right margin of the page. Press command-A to Select All.
    Go Arrange > Align > Top
    Go Arrange > Distribute Space > Horizontal.
    With all five tables still selected, press command-D to duplicate the set.
    Hold down the Shift key and press the left arrow once, then the down arrow 14 times. This should bring the new row of tables into line with the previous ones, and move them down the page to just below the first row of tables. If fine adjustment is needed, use the arrow keys with the shift key released.
    Repeat three more times to add another three rows of tables.
    Adjust the spacing between tables as necessary.
    Regards,
    Barry

  • Color Problem when Aadding/Removing series from Chart

    Is it possible to define the color of the series to add in a Chart?
    Actually, the color seems to be defined in a precise order by the chart itself when adding the series. I think there's a list of predefined colors and for each series added to the chart, it take the next color of the list. Then, when we remove a series, the pointer in that list of colors is decremented.
    That behavior does not suit me. If i remove a series and add it again there are cases where two series can have the same color...
    Example:
    add series 1 - color blue
    add series 2 - color red
    add series 3 - color cyan
    remove series 2
    add series 2 - color cyan
    series 2 and 3 have the same color
    (you can test this behavior)
    So is there a mean to avoid this problem and set the color of series ourself?
    Thanks

    If you search the http://javafx-jira.kenai.com you will come across quite a few open bugs to do with dynamically modifying charts by adding and removing series and data - so I guess, if you are currently using this feature, then proceed with caution (and don't use the chart animation feature) until they are fixed (and log new issues if yours is not already captured).

  • If I subscribe to match, can I remove music from my hard drive and still listen to it?

    I'm interested in Match, but want to know if the music has to be on my computer to access it on my iPod/iPhone?  In other words, once I sync my library (over 100,000 songs) can I remove them from my hard drive (of course having them backed up on my own) and still access them?

    First off, if you have a library with over 25,000 songs in it, you will not be able to even sign up for iTunes Match.  When you try, you will get a message that you are not eligible.
    No, you cannot selectively choose which songs go to iCloud to get around this 25k limit, iTunes Match wants all or nothing.
    The way around this is to set up multiple iTunes libraries, each with fewer than 25,000 songs in it.  While this is inconvenient on your computer, if you send them to the iCloud this way and they will all be available on your iDevices.
    Apart from that issue, the answer to your question is "Yes." 
    However, when you play a song, it downloads to your device or computer while it is playing and will stay there until it is removed again.  iTunes Match does not stream songs, it downloads them and plays them, although songs will start playing before they have been completely downloaded.

  • Is it possible to remove "Contacts" from my Mac mini and the reinstall it?

    Is it possible to remove "Contacts" from my Macmini and then reinstall it?

    The Contacts program has changed the name of a contact that I had a correct email address.
    The example you gave (now removed by a moderator) doesn't show that the email address changed. It shows that the recipient's name associated with the address changed. I don't know why that happened, but it doesn't necessarily indicate a problem with Contacts. You might have had two contacts with the same address.
    I don't seem to have a Address button in my toolbar.
    Open a message-editing window and select
    View ▹ Customize Toolbar...
    from the menu bar. From the sheet that opens, drag the button labeled Address upward (not downward) into the toolbar if it's not already there, then click Done.
    Click the button to see a list of your contacts. You can make multiple selections.

  • How can I permanently remove apps from my ipad, iphone and ipod (which are in icloud)?

    How can I permanently remove apps from my iphone, ipad, ipod operating in the iCloud?

    Apps don't operate in the cloud - they're either downloaded to your device, or they're in your Purchased list. You can't permanently remove the history of apps you've purchased, but you can hide them. See this link:
    http://support.apple.com/kb/HT4919
    Matt

  • Selecting both - Column and Rows in ALV Grid

    Hi All,
    I am developing a module pool in which in a ALV Grid Display the user wants to select multiple rows and multiple columns.
    How to set this in ALV grid? Right now I can set selection of multiple rows but once user clicks on column the rows are deselected and the column gets selected.
    Similarly when user selects on one column and clicks on another column the previous selected column gets deselected.
    Is there any way to do this in ALV Grid?
    Thanks,
    Rashmi.
    PS: I am using OO ALV for this development.

    Hi Andrey,
    I know this. I was just trying to find out if there is some other alternative to this.
    Anyways, this seems to be the only choice.
    Thanks,
    Rashmi.

  • How to remove pictures from the photo libary and mobile Albums

    Can anyone help me??? How do I delete photos from the Photo Library and Mobile Albums???

    CORRECTION.  After going to settings, select Photos & Camera.  Then select "My Photo Stream".  Change My Photo Stream to the "OFF" position.  This will delete all the pictures in your picture frame stream, so make sure you want to delete them.

Maybe you are looking for