Renaming 2nd Airport Express Unit

How do I rename my 2nd airport express unit (not the network, just the 2nd remote base station)?
Thanks!

Open AirPort Utility, select your AirPort Express and click Manual Setup
Click the Base Station tab/label just under the row of icons
Assign the new device name (and new device passwrod if you wish)
Click Update at the lower right of the window and the AirPort Express will restart in 40-45 seconds with your new settings.

Similar Messages

Can I extend the range of my Airport Extreme with 2 Airport Express units?

I am using Airport Extreme as my basic router. I have connected 2 airport express units (all new since 12/09) to extend the network about 300 ft into another building to a PC. I am receiving about 65% signal and only one of the express units is extending the signal. Previously I was able to extend the network with a Netgear router and one D-Link extender and achieved 85%.
I would like to use the 2nd express to extend the signal of the 1st express which is extending the Extreme.
If this is not possible, can I use something other than an express with the extreme to extend the wireless network?

Here are the basic steps in setting up a static WDS. Please compare them to what you have done to see if there are any differences. Hopefully, this will give you a clue on what to try.
AEBSn - WDS Setup
(Note: To facilitate the WDS set up, place the base stations within near proximity of each other during the set up phase, and then relocate them to their desired locations when complete. Also, jot down the AirPort IDs (MAC addresses) for each of the base stations to be used in the WDS. The AirPort ID and is printed on the label on the bottom/side of the base station.)
Main Base Station Setup
o Click the AirPort status menu in the menu bar and choose the wireless network created by the base station you want to set up as the main base station.
o Open AirPort Utility (located in the Utilities folder in the Applications folder on a Macintosh computer, or in Start > All Programs > AirPort on a computer using Windows).
o Select the main base station, and choose Manual Setup from the Base
Station menu, or double-click the base station to open the configuration in a separate window.
o Enter the base station password if necessary. If the base station is using the
default password of public, you will not be prompted for a password.
o Click Wireless in the toolbar, and then choose “Participate in a WDS network” from the Wireless Mode pop-up menu.
o Click WDS and then choose “WDS main” from the WDS Mode pop-up menu.
o Select the “Allow wireless clients” checkbox if you want client computer to connect to this base station.
o Click the Add "+" button and enter the AirPort ID of the base station you want to connect to this base station.
o Click Update to send the new settings to the base stations in the WDS.
Remote Base Station Setup
o Click the AirPort status menu in the menu bar and choose the wireless network created by the base station you want to set up as a remote base station.
o Open AirPort Utility (in the Utilities folder in the Applications folder on a Macintosh computer, or in Start > All Programs > AirPort on a computer using Windows).
o Select the remote base station, and choose Manual Setup from the Base Station menu.
o Enter the base station password, if necessary. If the base station is using the default password of public, you will not be prompted for a password.
o Enter the same network password as the main base station, if necessary.
o Click AirPort in the toolbar and click Wireless. Choose “Participate in a WDS network” from the Wireless Mode pop-up menu, and choose the same channel as the main base station from the Channel pop-up menu.
o Click WDS and choose “WDS remote” from the pop-up menu.
o Enter the AirPort ID of the main base station in the WDS Main field.
o Click Update to transfer the settings to the base station.
Relay Base Station Setup
o Click the AirPort status menu in the menu bar to join the wireless network created by the base station you want to set up as the relay base station.
o Open AirPort Utility (in the Utilities folder in the Applications folder on a Macintosh computer, or in Start > All Programs > AirPort on a computer using Windows).
o Select the relay base station, and choose Manual Setup from the Base Station menu.
o If the base station is using the default password of public, you will not be prompted for a password.
o Enter the same network password as the main base station, if necessary.
o Click AirPort in the toolbar and click Wireless. Choose “Participate in a WDS network” from the Wireless Mode pop-up menu, and choose the same channel as the main base station from the Channel pop-up menu.
o Click WDS and choose “WDS relay” from the WDS Mode pop-up menu.
o Enter the AirPort ID of the main base station in the Main AirPort ID field.
o Click the Add "+" button and enter the AirPort ID of the remote base station this relay base station will connect to.
o Click Update to transfer the new WDS settings to the relay and remote base stations.
(ref: Pages 42-46 of "Designing AirPort Networks.)

Multiple AirPort Express units - use more than one at a time?

If I connect three Airport Express units in three different rooms, can I use more than one at a time?
Can I choose to only use 2 out of the 3 at one time?
Thanks.

Yes. With iTunes 6.0.2 or later, you can send an AirTunes stream to multiple remote AirPort Express units, provided that each AirPort Express has the latest AirPort firmware. The maximum number of remote AirPort Express units is three to six in typical conditions. The number that works for you will depend on your environmental conditions (such as building composition and local radio interference), distance to the remote AirPort Express units, and available network capacity relative to your other usage.

Setting Up a Three Station (Multiple AirPort Express Units) WDS Network

For a mission project in Northern Ireland, I am trying to connect three Airport Express units into a single wireless system. The mission group is located in an old building with thick walls, so the wireless signal needs to be "repeated." I need help on the basics of setting up all three AX units in a series. One will be located in an office on the ground floor an act as the main base station with an ethernet connection. (The mission has a cable modem/router with an independent line in the ofice that is connected directly to the AX unit in the office.) The second will need to act as a relay base station(it will be on the second floor of the building, but in range of the main base station) and the third as a remote base station down a hall on the second floor. In an initial setup, I was unable to have the main base station unit show up on the list of base statios when I did a scan in the AirPort Admin Utility.
Should I set up (configure) all three AX units in close proximity to each other and then relocate them to the final locations? I also need some advice on how to identify or assign the AirPort MAC Adress to the units. Finally, do I need to do a "hard reset" on the units and simply start over? I saw the Apple article on using WDS to create a network from multiple base stations, but it only dealt with two units. Thanks. Sawyerlex
iBook G4 Mac OS X (10.4.6)
iBook G4 Mac OS X (10.4.6)

Check out my last post in this thread:
http://discussions.apple.com/message.jspa?messageID=1756749

2nd Airport Express wont show up in Base Station Chooser, iTunes

Hi, I have 2 Airport Express units on the same network. One is showing up, the other is not. Both were working perfectly. I recently upgraded my router to a Linksys BEFSR41. When I run the Base Station Chooser, one shows up the other does not. The same happens in iTunes. I can address the Airport Express by chooser Other from Base Station Chooser, then entering its IP address. I updated firmware in both units to 6.3. Both units are configured identically. If I access the hidden airport express from a wireless PC it shows up fine but the other one does not

Thank you for your post, but I do not understand why you are giving me a link to the generic airport express site. The configuration I have was working fine before I upgraded my router.

I have a older Airport Express unit that requires Airport Utility 5.6. When I try to install 5.8 on my OS X10.8 iMac, I get the message "Airport Utility can't be installed on this disk. The version of Mac OS X on this volume in not Supported"

I have a older Airport Express unit that requires Airport Utility 5.6. When I try to install 5.8 on my OS X10.8 iMac, I get the message "Airport Utility can't be installed on this disk. The version of Mac OS X on this volume in not Supported"

Why should I have to spend money to solve this problem? Many others have the same concern, Airport Utility 6 does not support older Airport Express units. This is Apple's problem. I've tried many solutions proposed on the net but none worked. I'm still trying for a work around.

Multiple Airport Express Units and Itunes

I have two Airport Express units, each is hooked up to a seperate stereo in the house. I tunes will connect with one or the other, but not both Airport Express units at the same time.
When selecting multiple speakers from the drop down box...the following error message is encountered..."The remote speaker "xxxx" does not support playback as a part of a group. Do you want to switch playback to it?"
Any help would be appreciated...when this is complete, the system will be doing exactly what I want.

The three most common problems encountered with mutiple AX's:
Itunes software (need 6.02 or better)
AX firmware (need 6.3)
Firewall (you must ALLOW UDP traffic)
If all these items are met then usually what remains is configuration and/or a range problem. Since it sounds as though it works singularly, range is not the issue. Check the three most common and if they are right you are left with re-configuring the network or possibly (but unlikely based on the post) a bad unit.

Lost connection to one of my Airport express units. Serial number 44500WQV0. Message in Airport Utility is to use Version 5.6 to configure base station. I have version 6.3.1. Both airport express units bought at same time few years ago.

Hello all.
Lost my connection to one of two airport express units. Both purchased few years ago. Use them to stream music to house speakers via WiFi. I have v6.3.1 of Airport Utility. Message says to use v5.6 to reconfigure this base station.
How do I do that, please?
Mahesh

You can use the following workaround to install AirPort Utility 5.6 on a Lion or Mountain Lion Mac:
Be sure to read the caveats at the end.
Lion / Mountain Lion's package installer will refuse to install superseded versions of AirPort Utility. Instead you will need to use a package extractor such as Pacifist or unpkg. Pacifist is shareware, unpkg is free.
Download Pacifist here: http://www.charlessoft.com/
Download unpkg here: http://www.timdoug.com/unpkg/
Download AirPort Utility 5.6 here: http://support.apple.com/kb/DL1482
When the AirPort Utility .dmg file finishes downloading, open it to expand and reveal the AirPortUtility56.pkg package installer file.
Directions for Pacifist (I do not have screenshots for unpkg but the idea is similar):
Open Pacifist and from its File menu, navigate to the package and open it.
Click the "reveal triangles" until you see AirPort Utility 5.6.app:
Select it and then click Install from Pacifist's toolbar. It will then be installed in your Utilities folder, and you can quit Pacifist.
The most recent version of AirPort Utility included with Mountain Lion should be used to configure 802.11n - capable AirPort Base Stations. Make no attempt to delete it. It and the older version (which will bear the unique name "AirPort Utility 5.6") can peacefully coexist. Use the older version only as necessary for older AirPort Base Stations that cannot be administered any other way.
If you happen to have an archived copy of the AU 5.6 app somewhere, such as a Time Machine backup or equivalent, you can simply restore it or drag the app to your Mountain Lion system's Utilities folder instead of resorting to the above procedure. It will run without complaint. It is only the package installer that is the problem.
Keep in mind that Apple's decision to abandon support for the original AirPort Express and AEBS was for reasons known only to them. Remember that you are using obsolete equipment, should some future OS X feature not work for you.

Airport Extreme works fine. Cannot see two Airport express units

Hello. I just bought a new Airport Extreme and 2 Airport express units to replace my old linksys routers and to take advantage of my new MacBook Pro and iTV units. I am a Mac newbie after 20 years of PC's. The Netgear DGND3300 DSL modem feeds DSL signal to the Airport Extreme unit and it works well with good internet and signal. I am trying to use the 2 Airport Express units to extend the signal around the house. The Airport Utility has seen both of them but then they disappear and it cant find them again. They are 10 feet away for now until I get them configured. How do I get them to connect and how do I configure them to extend the wifi range?
Thank you.

The first thing to check is your AirPort Extreme.
Open AirPort Utility - click Manual Setup
Click the Wireless tab/label below the row of icons
Make sure there is a check mark next to "Allow this network to be extended"
Update to save changes
You may have already done this, but it was not mentioned in your post and is a critical step to "extend" the network.
"Hard Reset" each of the AirPort Express devices by holding in the reset button for 10-12 seconds. Then power down one device and configure one at a time.
Open AirPort Utility - Click Manual Setup
Click the Base Station tab/label below the icons
Enter a name for the device, device password and adjust Time Zone settings
Click the Wireless tab
Wireless Mode = Extend a wireless network
Wireless Network Name = Same name as the AirPort Extreme wireless network
Check mark next to Allow Wireless Clients
Wireless Security = Same security setting as the AirPort Extreme network
Wireless Password = Same password as the AirPort Extreme network
Confirm Password
Update to save settings. Close AirPort Utility immediately as soon as you see the message that the settings have been stored. You should have a green light on the Express in 40-45 seconds.
Now, log back on to the wireless network provided by the AirPort Extreme and you should see the AirPort Express that you just configured, if you are using a Mac. The Windows Firewall or anti-virus software may block the connection if you are using a PC. (The AirPort Express "disappears" as soon as you click Update in AirPort Utility because it has joined another network...that's why you don't see it. It uses a "temporary" network with a name like Apple Network xxxxxs during the configuration only).
Configure the second AirPort Express the same as the first. You will probably want to assign a different device name to that Express to keep things straight.
To "extend" effectively, the Express should be located approximately 1/2 the distance between the AirPort Extreme and the area that needs more wireless coverage. Depending on obstructions, you may need to alter this distance a bit.
The "extend" setup works like the hub and spokes of a wheel. The AirPort Extreme is the "hub" and each Express resides at the end of a "spoke". Each Express communicates directly to the "hub", not to another Express at the end of another spoke. For that reason, you cannot "extend" a device that is already configured to "extend".
Message was edited by: Bob Timmons

Can I use a second Airport Express unit to printe wirelessly?

I have an Airport Express unit connected to my amplifier and my modem in order to listen to music wirelessly. I would like to use my Cannon ip4300 printer the same way. Can I use a second Airport Express unit to connect the printer to my modem? If so, how is it done? I am concerned about a conflict between the two Airport Express units. Thank you.

I do just this with a ip4200 printer - you "extend" the Airport network with the second Airport then plug the printer into the USB port, (you could plug it into the USB port of the first Airport as well)
In the Airport utility (use 5.6 or 5.6.1) select the Printers tab and it should be there.
Regards,
Shawn

I have 3 airport express units, an Ipod and a PC. I used the PC to set up an airTunes and the AirUtility can see all three of the airexpresses. The Ipod displays all of the airexpresses and I can pick any one to stream music to. PC won't - any ideas?

I have 3 airport express units, an Ipod and a Windows 7 PC. I used the PC to set up an iTunes/airTunes and the AirUtility can see all three of the expresses. The Ipod displays all of the expresses and I can pick any one to stream music to. The PC won't - any ideas? AirUtility tells me the 7.5.2 version of the firmware is the latest for the expresses and ITunes is also reporting that there are no upgrades available. I get an error code -15000 when I try to connect from the PC to one of the expresses.

How do I configure the AX to connect to the hub's wireless network? It will only scan one base station Airport Express at a time in the Airport Utility. I think what I am trying to do is use the hub as a router to the two AX's. Is there a specific way to set this up?
To set up the AX to join a wireless network as a "Wireless Client," using the AirPort Utility, either connect to the AX's wireless network or temporarily connect your computer directly (using an Ethernet cable) to the Ethernet port of the AX, and then, try these settings:
Launch the AirPort Utility.
Select the AX.
If not already connected to the AX's wireless network, go ahead and switch to it when prompted.
AirPort Utility > Select the AX > Manual Setup > AirPort > Wireless
Wireless Mode: Join a wireless network
Network Name: <type in the network name/SSID of the wireless network that you want to join or select it from the pop-up menu>
Wireless Security: None OR, if you are using security on your wireless network:
Wireless Security: <Select the appropriate level of security for the existing wireless network: WPA/WPA2 Personal | WPA2 Personal>
Password: <enter your wireless network security password>
Verify Password: <re-enter the same security password>
Click Update to write the new settings to the AX.

My Airport Express units and Apple TV are disappearing from my network for Airplay

I'm using a BT Home Hub (third generation) as the centre point of my network. The Airport Express Units, and the Apple TV, are connected to it wirelessly, using the 'Join A Wireless Network' option in the setup.
Although the units are visible on the network, they disappear from the Airplay menu on iOS devices and my MacBook Pro, and need to be rebooted to bring them back.
Does anyone have any idea why this might be?
The Apple TV Is now cabled to the router, which rectified a performance issue I had with it whereby films being streamed would stop periodically.
Prior to this, I had the devices wirelessly connected to, and extending, an Airport Extreme network, being broadcast from my Time Capsule. I had to change this however, as the Airport Express units did not play music smoothly and would also disappear from the Airplay menu. I figured that the Time Capsule was at fault, as it's around 4 or 5 years old, and has been showing signs of ageing for a while now, however this new problem has occured since.
I'm tempted to replace the Time Capsule, with a new Airport Extreme unit and external HDD unit to continue wireless Time Machine backup of my three Macs, but don't want to do this if not strictly necessary.

Is there a way to stream internet audio to these devices?
You might want to take a look at Airfoil for Mac to be able to stream any source on your Mac to the AirPort Express.
Rogue Amoeba | Airfoil for Mac: Wireless Audio Around Your House
Or, if you have a PC, you will need
Rogue Amoeba | Airfoil for Windows: Wireless Audio Around Your ...

Adding a 2nd Airport Express to extend the network using WDS

I am a bit of a novice, but after I installed an airport express with my d-link wireless router to play itunes on my home stero, the music kept breaking up and stopping. I tried to change the channel, but it said mine was set on automatic and I cannot figure out how to change manually.
So reading apple's suggestions, they said to get another aiport express and extend the network with WDS. I purchased my 2nd express today and have been trying to install it using the airport express assistant. I have had to reset the 2nd express and the original several times. However, what i keep running into is after it gets through all the steps, it asks me for a password for "this basestation". I have read several help topics and it looks like i need to use "public" for this new airport express. I get through that step and then it gives me an unknown error (-6753). Does anyone know what this is? Or is there a way to set-up the 2nd airport express manually? Do I even need a 2nd one? Should I just get an airport extreme? Will that extend the range of my wireless network? Any help is greatly appreciated. I have been at this for about 6 hours now. My wife is going to kill me.

Will the manual for D-Link describe how to set up the
first airport express as a roaming network
No
do that via the apple settings once its connected via
ethernet cable?
Yes
Different channel.
Same network name, same security.
Ensure that distribute IP addresses (under Network) is unchecked.
When this is done, will I still be able to play
itunes through the first airport express?
Yes
Also, then once I do that with the first, then do I
just do the regular set-up for the second as a
network extender via the airport express assistant?
Yes
iFelix

Airport express units no showing in airport utility

My airport extreme units are not showing up in the airport utility application.
I have an local wifi network established by linking an airport extreme to my ATT Universe router . This works correctly and the signal is good in most parts of our home . I had 2 airport express units acting as extension of the wifi network to the more distant areas. Somehow we lost the entire network when we were gone on a trip and I had to reinstall the airport extreme (works fine).
I know I need to reinstall the airport express units and link them to the existing network ...but they aren t showing up in airport utility . The normal process has been to reset them to their original configuration , then log on to them as a independent network ,then use airport utility to reset them as extensions to the existing wifi network.
Can t start unless they show up and they are a foot from my MacBook Pro .......I have 4 different units (only use two ) ? Nothing shows up .
What am I missing ?

Suggest that you work only with one AirPort Express (AX) at a time and leave the others powered off.
Perform a Factory Default Reset on the AX as follows:
Power down the AX
Hold in the reset button and keep holding it in while you plug the AX back in to power
Keep holding the reset button another 8-10 seconds then release
Allow 40-45 seconds for the AX to restart to a slow blinking amber light
At this point, the AX is producing a wireless signal with a name like Apple Network xxxxxx. You need to first log on to this network from your Mac if you want to configure the AX using wireless.
Or, you can use the Ethernet cable method to configure the AX and then disconnect the Ethernet cable once you have the AX updated with new settings
Repeat the process above fo the second AX, but note that the Apple Network xxxxxx with have different letters and numbers, as it will be a different network.

How to use 2 Airport Express units?

In my office upstairs I use an AirPort Express to tap into the wireless router downstairs wirelessly. Works great. In a bedroom also upstairs, I have a Blu Ray player I want to connect to the Internet. I thought if I got another AirPort Express unit in that Bedroom then it too could tap into the wireless router downstairs so I could then run an ethernet cable from the AirPort Express to the BluRay player. I tried that but when I look on my computer in the AirPort Utility screen, it only recognizes one of the AirPort Express units. That unit in the Bedroom continues to have a flashing yellow light and no internet connection. What do I need to do to get an internet connection in the Bedroom?

Welcome to the discussions!
+These past Holidays “Santa” delivered a new Mac Book Pro, along with a Time Machine which is built into an Airport Extreme.+
You have a Time Capsule, correct?
The Time Capsule can "extend a wireless network" as well as perform backup functions on the network.
You could continue to use your AirPort Express in another part of the house to provide a stronger wireless signal in that area. (I've yet to meet the first person who felt that they had too much wireless coverage in their home).
If you have a DVR or newer DVD player that requires an ethernet connection for advanced features from the internet, the ethernet port on the Express is "live" when it is set to "extend", so you might think about that option as well.
Hotels don't use ethernet nearly as much as several years ago, but I always take my spare Express on the road to hook up to the hotel's ethernet jack and create a wireless network in the room for the laptop or iPhone. Works great.

Renaming 2nd Airport Express Unit

Similar Messages

Maybe you are looking for