Repeater Access Point 1240 works like WGB client

Hello, i have a problem. In my Network i have 5 Access Point. 4 Aironet 350 and 1 Aironet 1242. IOS for aironet 350 is12.2(13)JA1, E .
Ios for Aironet 1242 is 12.4(10b)JDA3.
Then .. I have an Access Point 350 configured as Access Point/root while all the other Access Point are configured as Repeater/non root.
My problem is that the Cisco Aironet 1242 is the last Access point in the chain, but not work fine.
all the Wifi client connected to Aironet 1242 not access to wired LAN.
I not ping all the Wifi client connected to Aironet 1242.
p.s.
My Aironet 1242 is seen in the association table of the its parent Access point like WGB_CLIENT.
any suggestion

Hi,
here is the link which mat help you!!
http://www.cisco.com/en/US/products/hw/wireless/ps430/products_configuration_example09186a00805b9b87.shtml
Regards
Surendra

Similar Messages

List of routers/access points that work/don't work with new airport extreme

Lets try to put together a list of routers/access points that work with the integrated airport extreme in the new intel macs and 10.4.5 (or 10.4.4) The purpose is to determine what is needed to make this work.
1) only wireless g, 802.11b does not seem to have this problem, psp probably is not supported by most 802.11b cards so its probably disabled in that mode.
I'll start off.
imac dou core. ( 1 week old)
dlink 2100ap , wireless g , does not work, slow not paifully slow internet access, very degraded video/audio streaming over local network.

I'm afraid 11b is affected.
I have a D-Link DSL 604+ router, which is 11b only.
Wireless is very slow, I noticed it right away. I get the sawtooth readout in activity monitor's network section.
Also, after putting the iMac to sleep it cannot find my wifi network upon waking. I have to restart the system before it'll connect to my wifi network again.

Access Points Not Passing DHCP to Clients

I have a 50+ access point deployment, all in a single VLAN (DMZ), across a dozen buildings. We recently experienced wierdness of the following sort. Clients would request DHCP request, DHCP servers would forward requests, which would not get passed from the AP to the clients. We could verify that DHCP and all other parts of network were fine. I had to cold boot each AP to clear the condition. I could find nothing in this mix of 350s and 1200s or the spectrum that would indicate an obvious attack... Couldn't find where to start looking for any tables that were full, or any real place to look for some other reason for this. Yet after cold boot- all is well.
Any thoughts, in case it happens again?

Hi Guys,
I am having a similar problem to you, however i can get authentciated via LEAP, but dont seem to get an IP adderss from the radius server.
My setup is very simple as i am at the design stage. We have a Cisco AP 1200 (2.4 and 5.0 GHZ) and we are using FUNK steel belted RADIUS server. LEAP authentication works fine and i can see the association on the AP. The wirless client (HP W400 integrated Wireless cards) shows that it has been authenticated successfully too. However no IP is being received. We have a IP Pool configured on the SBR server and the SBR server shows that it has issued an IP address.
Next step was to place a sniffer and capture the packets. The capture shows the radius requests and challenges and in the very last ACCEPT packet we can see that the SBR has issued an IP address.
I am confused as i cant see anything on AP that would block the IP address. There are also a few attributes showing as "unknown" in the sniffer trace, so im not too sure wgats going on.
Can anyone help. The IOS is 12.2 (13) JA

Access point not work correctly

Hello everybody, I have a problem in my BlackBerry Passport. I can't turn on "access point" function,this function not work. Does this function work in the future OS updates?
P.S access point give your internet from the mobile network to your WiFi

Hotspot does work on all versions of BlackBerry 10 OS and all BB10 models. It is, however, controlled by your carrier. If it won't turn on you have one of several possible problems:
1) Your mobile data is off or not working.
2) You need to have Hotspot provisioned on your account by your carrier.

Access Point 1240 Support for BBSM5.3

Hello,
I have 3 ap 1240 for install with bbsm 5.3, but when I add the access-point to the bbsm , the bbsm does not recognise has a valid access-point.
Does any one know in what version of bbsm is supported ap1240.
Thanks

Hello there,
I have a customer who has a BBSM 5.3A which is running the latest patch (5332) and it cannot discover 1242 series AP's as valid network elements. They get the following:
2009/01/07 12:01:53 Pinging X.X.X.X...
2009/01/07 12:01:53 X.X.X.X is ACTIVE
2009/01/07 12:02:18 X.X.X.X: not a Network Element or SNMP password is not ******
2009/01/07 12:02:18
2009/01/07 12:02:18 Pinging X.X.X.X...
2009/01/07 12:02:23 X.X.X.X: no response
2009/01/07 12:02:23
2009/01/07 12:02:23 Pinging X.X.X.X...
2009/01/07 12:02:23 X.X.X.X is ACTIVE
2009/01/07 12:02:47 X.X.X.X: not a Network Element or SNMP password is not ******
2009/01/07 12:02:47
2009/01/07 12:02:47 Pinging X.X.X.X...
2009/01/07 12:02:47 X.X.X.X is ACTIVE
2009/01/07 12:03:12 X.X.X.X: not a Network Element or SNMP password is not ******
2009/01/07 12:03:12
2009/01/07 12:03:12 Pinging X.X.X.X...
2009/01/07 12:03:12 X.X.X.X is ACTIVE
2009/01/07 12:03:37 X.X.X.X: not a Network Element or SNMP password is not ******
They have assured me that the SNMP info is correct as they have checked it several times but the BBSM still doesn't recognise the 1242's. I know that the document link above specifies that 1200's are supported but don't Cisco class the old 1200's, 1230's and 1242's as different? Also, the BBSM didn't recognise some of their 2960-24 switches as valid network elements either but they selected the object type themselves from the list.
Thanks in advance.
Leigh

Access point 1240

i have 1240 access point with radio interface 802.11A/G up ...but i'm getting error while creating vlan that i can't creat it because the radio is not installed ...
can some one support me if he face same issue please

Can you please post the output to the following commands:
1. sh version; and
2. sh ip interface brief

PC54G Access Point half working

My ADSL Internet connection comes through the modem to a switch then to a desktop pc via lan which is also fitted with a PC54G wireless card. I have 2 laptops with 801.11g wireless cards, I can get a normal network, email and I can ping the modem from them and that is all. I cant ping the outside world or receive the Net, MSN messenger, ICQ etc. I have tried a few configurations without success.
What should I use, Access Point or Gateway?? Should I have bridged connections, if so which ones?? Anything else that might help

I think you must use a ACCESS Point
and you must enable DHCP client on your HOST PC
Some Internet connection dosnt support manual sharing of internet

Repeater access point

Gents
I configured an autonomous access point as being a repeater to a root one. I ping the root from the repeater and it is showing as connect. however,the wireless coverage has not been extended?
what is the problem?

Hi,
here is the link which mat help you!!
http://www.cisco.com/en/US/products/hw/wireless/ps430/products_configuration_example09186a00805b9b87.shtml
Regards
Surendra

Stor.E access point stops working after a few seconds

Purchased a Stor.E Wireless Adapter and followed instructions but after turning the device on by connecting to USB power using supplies cables, WIFI access point disconnects after 4 or around seconds.
1. i connect the device to usb power
2. Power light blinks green and stays on
3. wireless light becomes green and stay on, turns off after a few seconds
Managed to connect to it using the mobile app a few times, while its on, but since the WIFI point disconnects, cannot use it.
Any thoughts ?

1. i connect the device to usb power
The Stor.e Wireless Adapter should be connected to mains power and the other end to the external HDD.
Then you could use the app to access the content wirelessly.

Permit mac-address only port 80 on access-point 1240

Hi,
how can I permit forward an mac-address which connect at access-point only
surf in Internet ?
Does anyone advice me an a configurations or document about ?
Best regards
Lorenzo

hiiiii...
permit

How to Setup WRITTEN as a wireless access point to work with WRITTEN

Hi,
I had a router WRITTEN which was not covering the whole space in my house. I was looking for a N wireless access point or a range extender.
The shop seller convinced me to buy WRITTEN saying that the Dual N will fix my problem.
well it did not. The reception in some locations is still poor.
the same reseller advised me to use the 350N as a wireless access point instead of buying one. The question is how to do it.
I am thinking about the following:
1- Have the WRITTEN installed next to the internet modem connect to the modem by cable
2- in another room have the WRITTEN (approx 20 meters away) not connected by a cable to the WRITTEN
3- When using the laptop in the weak reception area, I try to connect wirelessly to WRITTEN which should be also connected wirelessly to the WRITTEN
Would that be possible. I hope so since there is no way to have a cable connecting the 350N and 610N due to many reasons
appreciate your help in adance

I am sorry but the spelling checker repalced my router names to another word
the correct text is:
I had a router WRT350N which was not covering the whole space in my house. I was looking for a N wireless access point or a range extender.
The shop seller convinced me to buy WRT610N saying that the Dual N will fix my problem.
well it did not. The reception in some locations is still poor.
the same reseller advised me to use the 350N as a wireless access point instead of buying one. The question is how to do it.
I am thinking about the following:
1- Have the WRT610N installed next to the internet modem connect to the modem by cable
2- in another room have the WRIT350N (approx 20 meters away) not connected by a cable to the WRT610N
3- When using the laptop in the weak reception area, I try to connect wirelessly to WRT350N which should be also connected wirelessly to the WRT610N
Would that be possible. I hope so since there is no way to have a cable connecting the 350N and 610N due to many reasons
appreciate your help in adance

Help accessing NAS - not working like before iCloud...

Hi:
So before upgrading my mobileme account to iCloud I was able to acces a hard drive attached to my airport extreme remotely. I believe this was done by enabling back to my mac in mobileme. When opening the finder, the NAS would appear in the sidebar. This worked when I was away from home and connected to the internet on a network other than my home network.
Since upgrading to iCloud when on a network other than my home network, the NAS doesn't appear in the sidebar as it normally did. Trying to mount the drive remotely by clicking on recent items isn't working either.
I enabled back to my mac in iCloud, but that doesn't seem to have worked. Any idea?
Thanks!

Unfortunately that solves it... Thanks.

Silly doubt abt access-points and bridges

hi all i have read cisco doc wherein clients connecting to access-points and also where the cisco access-point is working like a bridge and still clients can connect to it .
then any specific reason why people generally connect clients to access-points.
i mean is there any benefit of either method over the other.
any help and guidance would be really helpful.
regards
sushil

In short, it is preferred to have users connect to access points.... 99% of the time. You can use a wireless bridge (that is associated to an AP) that is connected to a switch/hub to supply network connectivity to wired users off the switch/hub. There are also access points that can be used as a bridge for building point to point connectivity.
Look at the home users with wireless.... it allows then to move from place to place (as long as there is coverage) without having to be wired in.

WGB & light weight Access Point

Hello Experts,
Need your suggestion, though I have gone through some documents the solution does not work as per my requirement as below. Still to confirm.
I wants to use LAP in flex connect mode & standalone access Point to act as WGB. However, as my standalone AP is dual band I want to use 5GHZ for backbone & 2.4 GHZ for my wireless users can it be possible?
Or, over the same backbone can I pass multiple VLAN traffics ? as I, have read it as client after configuring the WGB in standalone so, it should not work !!!
Thanks in advance!!
Lenka...

Yes, you can configure the 5Ghz to handle your "backhaul" if you will from WGB to FlexConnect LAP. Just make sure that only 5GHz has the "station-role workgroup-bridge" configured. 2.4GHz radio will keep the station-role root, for your client access.
The second question; multiple VLANs. Customer facing documentation is conflicting, but newer documentation shows this should work.
http://www.cisco.com/c/en/us/support/docs/interfaces-modules/wireless-lan-controller-module/115752-mesh-wgb-00.html
On the WLC, make sure you enable WGB Vlan support
>config wgb vlan enable
On the WGB you will need to make sure you have the SSID setup with
# workgroup-bridge unified-vlan-client
and then make sure you have all your applicable sub-interfaces on radio and Ethernet.

Bypass an access point for packet sniffing

Hello,
I have recently set up a WiFi network with WPA/PSK connection and a tablet PC with Windows 7 with "connectify" to act as a repeater/access point. But I would like to use the client running Arch connected to the repeater to log the traffic after the access point/repeater/gateway with, how do I do that?
Main Access point/gateway connected to the internet has an IP address of 192.168.10.254
Software repeater (connectify) has 192.168.2.1
Client has 192.168.2.102
So far I can only "see" the traffic between the client and the repeater.

I'm not entirely sure I understand this, but as far as I can tell you have a setup as follows:
Gateway--Windows 7 Tablet--Arch Client
I'm unsure what exactly you're trying to do with the Arch client. What exactly do you plan to log? How are the devices connected together and how many interfaces does each device have?
I *think* I have a vague idea of what you're trying to do, but I can't help until I know what you're working with in more detail.
Jon

Repeater Access Point 1240 works like WGB client

Similar Messages

Maybe you are looking for