Replace DVD Combo Drive on eMac

My DVD combo Drive is going on my eMac, and I'd like to know if I can buy a replacement through Apple or through a 3rd party. Also would like to know how difficult it is to replace by myself. My machine is an eMac 800 MHz PowerPC G4, 1gig Ram. The specs on the drive are:
PIONEER DVD-RW DVR-104:
Firmware Revision: A227
Interconnect: ATAPI
Burn Support: Yes (Apple Shipped/Supported)
Cache: 2000 KB
Reads DVD: Yes
CD-Write: -R, -RW
DVD-Write: -R, -RW
Burn Underrun Protection CD: Yes
Burn Underrun Protection DVD: Yes
Write Strategies: CD-TAO, CD-SAO, DVD-DAO
Media: No
Any help is appreciated. Thanks, Steve

Most of the readers of the "Older Hardware Products" section have some familiarity with products pre-1997. Your eMac is positively modern by comparison.
You would get more readers, and therefore be more likely to get better advice, on the eMac forums:
Category: eMac
Just click on the most appropriate Forum in that category to get a "Post a New Topic" button.

Similar Messages

DVD combo drive failing on eMac

My DVD combo Drive is going on my eMac, and I'd like to know if I can buy a replacement through Apple or through a 3rd party. Also would like to know how difficult it is to replace by myself. My machine is an eMac 800 MHz PowerPC G4, 1gig Ram. The specs on the drive are:
PIONEER DVD-RW DVR-104:
Firmware Revision: A227
Interconnect: ATAPI
Burn Support: Yes (Apple Shipped/Supported)
Cache: 2000 KB
Reads DVD: Yes
CD-Write: -R, -RW
DVD-Write: -R, -RW
Burn Underrun Protection CD: Yes
Burn Underrun Protection DVD: Yes
Write Strategies: CD-TAO, CD-SAO, DVD-DAO
Media: No
Any help is appreciated. Thanks, Steve

Hi Steve,
No-one bothers with Combos these days as Superdrives (DVD burning) are quite cheap.
I replaced in my eMac a Combo, originally a Pioneer drive with a Pioneer Super DVD 109 8X DVD-R/RW drive from OWC. It works great.
The current model is a DVR - 115 D but is essentially the same and would suit your model.
https://eshop.macsales.com/shop/optical-drives/superdrives/powermac/
Installing it was easy.
Remove the shell, and carefully disconnect the power wire.
Remove the screws that hold the optical drive, slide it out and install the new one.
No software drivers are needed.
regards roam

Replacing DVD/CD Drive (Question)

Hello!
I need to replace dvd/cd drive in the PowerMac G4 (AGP). Looking to add DVD+RW/CD. Can I purchase any DVD+RW/CD drive? Most DVD+RW/CD box says Windows specs.
Thanks,
Jamie

Hello!
Thanks for your reply. I have data on the DVD-R disks and it won't boot or show up on the Powermac G4 desktop. I see Best Buy sells internal drives, but not sure it's Mac?
http://www.bestbuy.com/site/LG+-+Super-Multi+24x+Internal+DVD%26%23177%3BRW/CD-R W+Drive/2691169.p;jsessionid=A690FC3F349615E56DDE5EE94E44A435.bbolsp-app01-51?id =1218353455613&skuId=2691169&st=dvd%20drives&cp=1&lp=5

Can I replace my combo drive with a superdrive??

hello all,
Can I replace my combo drive with a super drive? I see on some of the tech do it yourself pages the G5 17" original imac is supported for changing it out by your self. but how do I go about buying the superdrive...and from whome??
thanks,
marc

As to the DIY installation...I purchased an OWC Mercury 8x dual to replace my combodrive, but the installation directions that everyone refers to on the apple support site says nothing about removing the mounting cage to use in the replacement installation. Am I missing something here? Sure, I can remove the three mounting screws that holds the cage to the drive, but then I'm left with the welded bracket that does not seem to want to move. OWC support was no help at all. Is there a trick to this?

Cd-rom dvd combo drive question

Hi folks, I'm currently experiencing probl with my cd-rom dvd combo drive cheepo "rosewill". When I'm playing dvd movie the sound is clicking and it's really anoying.To make sure it is dvd combo drive , copied dvd (vob) file to comp, and then played; Sound was perfect.is this something wrong with my dvd drive or I just missed something ??

definately the drive, tried 2 brand new dvd's no luck. Gonna rma, thanks anyway
Rob

IBook Tangarine with a cd/DVD combo drive.

Hi,
I've recently see on the UK Ebay site a Tangarine iBook, where the seller has upgraded it somewhat and put in a CD/DVD combo drive. (http://cgi.ebay.co.uk/ws/eBayISAPI.dll?ViewItem&item=8802810218&sspagename=ADME% 3AL%3ARTQ%3AUK%3A1&rd=1)
I contacted the guy to ask him what the make and model of the drive was and he told me it was a Toshiba SD-C2502 drive. He said that you need to use F12 to open it and hasn't mentioned if it has suffered from any cosmetic damage.
I have a Blueberry iBook and I'm interested in upgrading it to have a cd/DVD combo to watch DVDs on. I've previously put in a 60Gb hard drive using the wonderful instructions recommended by users her from PBFixit.
Is this feasible and has anyone done that before? If so can you tell me whether it's wrth the effort?

Hi ScoringSkins -
It is possible to install a DVD drive in your clamshell. However, there have been reported problems with using Apple's DVD Player (in OS X) to view the DVD's because it requires the Rage128 or later graphics chip. There are other players that will do the job.
Check out the drive database on the site www.xlr8yourmac.com for drive compatibilities and optional DVD players.

CD/DVD combo drive ejects CDs-but only specific ones !!

hi all,
I have the following problem with my mac mini:
a)when I enter any movie DVD, it is either ejected in a few minutes, or worse, it just sits in the Drive,(no mounting on the Desktop) and I have to restart (w/ mouse button pressed to eject)
b)any movie CD I enter (recently got brand new PoC-DMC; so no scratches etc on it too) same as (a) above
c)Insert the "Mac OS X Install Disc 1 and Apple Hardware Test" DVD (that came originally with my mac mini), and same as (a) above
d)However, insert the Mac OS X Tiger Upgrade DVD and it WORKS!!!
As of writing this, both Disk Utility and Sys Profiler have hung up. though had the same problem as mentioned above yesterday too, and then Sys Profiler was listing the combo-drive, and Disk utility was not. (as per what i read on some other posts in this forum, that would be proper behavior by the system)
Would appreciate any insights into this.
Thanks
mac mini 1.42GHz PPC G4, 512 MB RAM Mac OS X (10.4.9)

Is there any other means of resetting a hardware
optical drive??
I'm not confident this will work but it's worth a try, it certainly won't damage your machine. Boot into Open Firmware ("Command + Option + O + F" on startup chime) and run 'reset-nvram' followed by 'reset-all'. Then boot into OS X by typing 'mac-boot'.
If this doesn't work boot into Open Firmware again and run 'eject cd' followed by 'mac-boot'.
You could also try forcing OS X to accept that the drive isn't in use by following the instructions here, however they do assume that a disk is stuck in the drive.
Matt

External USB CD-RW/DVD-RW drive for eMac?

Hi, I'm running OS 10.3.9 on an early model (2002) eMac. The computers' built-in CD-RW drive (HL-DT-ST CD-RW GCE-8240B) is completely shot; it won't read anything. I'm considering getting an external USB CD-RW/DVD-RW drive; anyone know what make and model would be best for what I have?
Thanks,
James

Do yourself a favor and avoid a USB drive- your eMac is USB 1 and the speed is impossible slow. Get a Firewire drive instead. You'll pay a little more, but it's worth it.
BTW, did you try to clean the head on the drive? On of thos Cleaner CDs from Wal-Mart (or your favorite store) often time can fix a drive that won't read anything.

Replace dvd-rw drive with hdd (lenovo 3000 n200)?

I would like to know if it is possible to replace internal optical drive and put insted a second hdd. If it is possible, then which type of hdd will suit 2.5" SATA or PATA?

I have a Lenovo 3000 N200 0769-ANU. I doubt you can fit an HDD into the optical drive slot, good luck.
Link to picture
My model takes a 2.5" SATA drive natively. The appearance of my SATA drive outside my machine looks like the illustration, which is larger than life size.   Look at the bottom of your laptop. There is a hatch covering the HDD, fastened by  2 screws.   Remove that hatch to see what your current HDD looks like.
I looked but could not find an illustration of a SATA drive installed in the bay of a compatible laptop. Below is an image of the drive connector as it would look from the top and outside of the laptop bay.
Link to picture
This connection differs greatly from that of an old-style IDE connector, you should be able to spot it instantly if you remove the hatch.
    A fast option to add a 2nd HDD to your model is to acquire an eSATA capability. Unfortunately the 2nd HDD will have to be external. Buy an eSATA-Expresscard adapter, an eSATA capable external hard drive enclosure, and a compatible SATA HDD. For best usability,get the same make, model, and capacity as the SATA drive in your laptop. That way you can swap the HDDs when (not if) the HDD installed in your laptop dies or gets terminally confused.   HDD prices vary. The other hardware can be purchased for about $50.
    An eSATA connection is just as fast as the connection to your HDD built into your laptop. This is a unique feature of eSATA connections. Unfortunately you will have extra cables and a box outside your machine, possibly with an external power supply for the 2nd HDD.

UltraBay CD/DVD Combo Drive Compatibility with X200 UltraBase

I have a T500 with a CD-RW / DVD-ROM drive (part #44C1930). Wondering if this drive is compatible with the X200 Ultrabase or I need to get a whole new drive altogether?
Help would be appreciated.

if it is from the T400, T500 or W500 then it is compatible with the X200 ultrabase.
Regards,
Jin Li
May this year, be the year of 'DO'!
I am a volunteer, and not a paid staff of Lenovo or Microsoft

Qosmio G10-133 Question about DVD COMBO Drive replacement

Hi
my laptop has a DVD driver labled UJ-830B but the device managaer reports that it is a UJ-830S. I have posted before saying I haven't been able to burn DVDs. It gets part way through then errors out saying unable to burn. I have used various software and disc makes but all to no avail.
I purchased an external burner which burns no problems, however it does defeat the object of having one built into the lapotop!!!
Can anyone suggest a suitable replacement drive? I have already tried an NEC 5540A drive, but my laptop didn't recognise that it was installed. I assume it is something to do with Master/Slave?? If the laptop doesn't recognise the drive I am obviously unable to flash any firmware.
Somebody please help.....

Hi
Seems you have already noticed that the drive replacement is not so easy.
The internal notebook drives dont support any jumpers like the external drives for desktop PCs and the settings are fixed and in my knowledge not changeable
I found some compatible drives numbers but unfortunately, I did not find the drive names.
It seems this are any internal part numbers.
DVD Super Multi Drive
- MATSU****A (G8CC00021610) UJ830
- MATSU****A (G8CC0001S610)
DVD Super Multi Drive (supporting Double-Layer)
- MATSU****A (G8CC00021611)
- TEAC (G8CC00024611)
However, the service partner could provide you a information about compatible drive.

Won´t accept CD-R, but works fine with DVD (Combo-Drive)

Hi there,
my emac got stuck after using a audio-CD with a little scratch. After restart I introduced normal CD-R, but they just got ejected by themselves after a few strange noises and about 5 seconds. I put in the MAC OS X start-up DVD, and it worked perfectly.
The question is: is there anything I could do, besides upgrading my eMAC after all to a Superdrive?
Doing some reliable(?) Internet research, it looks, that that can´t be too hard, and my warranty has expired anyway. So the second question goes:
Which brands and models are working fine? (Looks like Pioneer does, but only them?)
Thanks a lot,
Daniel.
eMAC Mac OS X (10.3.9)

Hi,
I had the same problem on my 14 month old (under-used!) 1.25 combo, would read dvd fine but not cd-rw, I tried a cleaning disc and even took out drive to blow out any possible dust! still no luck.
I then decided to go superdrive and put in a Pioneer 110D cd/dvd burner as this seemed the popular choice, I found installation easy, I left the jumper on back of cd burner on 'CS' as my original one was set to that. I then fired up emac and installed 'Patchburn 3' software patch available as a download from the internet to finish the installaton. So far it all seems ok!

Replacement dvd-rw drive

Hello all,
I currently have a apple G5, it has a sony dvdrw drive already installed. I think the sony driving is showing signs of failing. So, I would like to replace it with a new LG or Samsung DVDRW drive. When I went up to look at the two of them at Bestbuy. None of them said anything about working with Mac computers.
So, I am wondering am I able to install a new dvd drive. Even if it does not say anything about being Mac compatible?
Thanks
Mike

You may be able to install it, but many need a specific firmware to be able to:
1. Boot Mac OS X disks.
2. Use iTunes for CD burning
3. Use iDVD/Disk Utility/Finder/DVD Studio Pro for DVD burning
http://www.patchburn.de/ solves that problem with some third party drives. But to ensure your internal drive works well, I suggest getting one from a place that sells known patchburn.de compatible drives such as http://www.macsales.com/
http://www.xlr8yourmac.com/ also has a good drive database where you can learn what drives will work, and what won't.

Replacing dvd/cd drive

I need to replace my dvd drive on my hp compaq presario v3000.
how to do that? what are the suitable matches?
how do I know inter face of my drive whether it is ide or sata for v3000 with out removing the existing damaged drive?

The removal and replacement procedure is available in the following weblink:
http://h10032.www1.hp.com/ctg/Manual/c01035667.pdf
Please provide the exact model number or product number to suggest suitable matches...
I am an HP employee.
Regards,
Vidya
Make it easier for other people to find solutions, by marking my answer “Accept as Solution” if it solves your problem.
***Click on "Thumbs up" button to the bottom right side of my post to say thanks!***

Replacement DVD/CD drive for IMAC 20

My AD-5630a drive refuses to burn anything in any format. I have tried 5 different brands of media, cleaned with CD cleaner, used compressed air, changed speed, and even talked nice to it. I have read an numerous amount of complaining about this same problem with these optical drives, with no answers. I wanted to buy a replacement drive also, but they are very difficult to locate and have almost given up. Since these drives are so finicky and so many have failed in the same way, I wonder if there is some other manufacturer that makes them. If so, who and what models would be compatible.

More info for all you out there that think that they can get to the bottom of this. The superdrive can read and write CDR's and can read and play DVD's. Just can't burn them! I have used a couple different type of DVD's and what happens using Disc Utility is that the burn process starts, then very quickly goes to "finishing burn". I then get a message that says "Unable to burn (insert title here) the disc isn't writeable"
I am using DVD-R (and have in the past). I have had great experience with the HP brand that allows for inkjet printing on the surface. However, I have gone to Memorex (same problem), then to a different HP and this is all I get. I have used Tayo-Uden as well. Any ideas?
Thanks!

Replace DVD Combo Drive on eMac

Similar Messages

Maybe you are looking for