Replaced Hard drive and logic board on ipod 5.5g...still get sad ipod HELP!

I've tried searching around the forums to see if anyone has had this similar problem AFTER replacing the hard drive in their ipods. Of course there are tons of people with similar issues, and the responses are always "replace the hard drive", so I'm going to see if there are any other possible issues out there that I could look into. So here's my situation specifically.
I have an ipod video 80 gig, and it seemed as if the hard drive pooped the bed on day 366 (only a slight exaggeration) after purchase, putting me right outside of my warranty. The apple store wouldn't do anything without charging me the cost of a new ipod to repair it. So, it had been sitting in my desk drawer for almost a year when I finally got around to replacing, and upgrading, the hard drive. I found a 120 gig drive on ebay, which after an email confirming my model, the seller said should work as a replacement. After installing the hard drive, I got the same exact problem that I had before. It would say to "wait. low battery", then the apple logo would show up with no back light, and then it would go right to the sad ipod face. I left it charging for a couple of hours, and it would just keep cycling through those three screens, until dying eventually after unplugging it. If I hook it up to my computer, nothing happens besides the ipod trying to charge. When I try to force it into disk mode, it seems like the ipod will reset to the apple logo screen, but it goes right back to doing the same little dance. I tried opening it and checking the cables a couple of times, and the last time, I broke the little cable clamp that holds the lcd ribbon. So...I ended up buying a replacement logic board. I installed that, hoping the logic board may have been the problem all along, and as soon as I plugged it in...same old crap. Now, in a last ditch effort, I've ordered a new hdd ribbon to see if that remedies the problem.
I realize that I should have perhaps waited a week until it comes, to see if that fixes it. But to be honest, I can't see anything wrong with the hard drive cable that I have right now, so I remain doubtful that it's going to fix anything. What I'm wondering, is if anyone has any idea if there is something that I may have overlooked, or if I might be barking up the wrong tree? Is it possible that the hard drive that I ordered was broken when I installed it? The seller (who seems to be a reputable seller on ebay, with lots of positive feedback) said that they test all of there hard drives before selling/shipping, and that there is no way that they shipped me a broken one. They also seemed convinced that the hard drive would work with my model. Is there anything other than the hard drive, or logic board that could cause this type of problem? Is the hard drive ribbon the only other possibility? Is there something software wise that I can do?
Please. Any feedback or help would be greatly appreciated. I've spent more on this thing than I could have paid for a used, but working one, and I'm about to lose it.
Thanks!

UPDATE:
Ive installed the new hdd ribbon. It seems to have gotten me a little closer to solving my problem. I am now able to get into disk mode, and if I reset it, I can get to a screen telling me to connect my ipod to itunes and restore it. However, after the restore process, it says it's resetting the ipod, and then it goes right back to telling me that it needs to be restored. I've been trying to search all the forums on the "restore loop". It seems like a lot of people have had luck changing the drive letter. My problem is, that I can't get into the disk management window. When I try to click on it, I get the "program is not responding" and the window freezes until I close it. Again, I'm using windows Vista 64.
Any help would be GREATLY appreciated. I'll just try to keep trying, and keep looking around in the mean time.

Similar Messages

Hard drive and logic board failure

Hi everyone,
we have been suffering from 4 dead hard drives and one logic board failure in 20-inch intel iMacs (~2007) recently and last month the logic board and hard drive of a 2010 27-inch iMac (just out of warranty) just died.
Are there any known issues with the iMacs that Apple fixes even outside the warranty?

Frank: I have a 5 month old 27" iMac and the logic board on it just died as well as I was getting all kinds of kerner errors. I have Apple Care and although the cost to replace the product was $800 I am not going to have to pay anything. I did talk to someone else who also had a logic board go bad on him but I doubt that you will be able to get it fixed without having to fork over $$$

Hard drive crashed on my MacBook pro and had to replace drive and logic board. When I connect my iPhone and try to sync I get a dialog box stating iPhone is synced with another iTunes library, erase and sync? How do I sync with iTunes without erasing?

Hard drive crashed and had to replace drive and logic board on my MacBook pro. After Install tried to sync with my iPhone and a dialog box pops up stating "this iPhone synced with another iTunes library, erase and sync?". I checked the manually manage music and videos box because I don't want all my wife's pics and music on my iPhone. How do I Sync without erasing what I have on my iPhone???

columbus new boy wrote:
How crap is that?
It's not crap at all.
It's not that simple. For example, I've 3500 songs on my MacBook but don't want them all on my phone, so I have to manually select each song again???
There has to be a solution.
Why not simply make a playlist with the songs you want on the iPhone?
and maintain a current backup of your computer.

Macbook Pro replacement hard drive and re-installation of OS X

My son's Macbook Pro (mid 2009) started crashing on boot up and gave a input output error. I have replaced the original 250gb hard drive with a 750gb drive and also upgraded the ram from 2 to 8. Finally I have also replaced the battery. I am using Leopard installation dvd to re-install the software but can only progress as far as the screen 'Install Mac OS X' but there is no disc offered to install it on. By using Disk Utility the only disc shown is the dvd. Pressing the 'New Image' tab I entered 'Save As' 750gb WD HD and 'custom size' as 750 gb. Utility Disk informs me that the disc is only .75mb? Any suggestions to solving my problem and completing the installation program?

Niel, I've checked the connection to the hard drive and all is good but as a check I have disconnected and re-connection the cable to the hard drive and the board. I have also 'listened' to the hard drive and it appears to be spinning. Unfortunately, the Snow Leopard installation disc gets no further with its installation. Are Macbook Pro's of this age prone to cable breaks, or am I using the wrong disc for a full OS X installation, if Snow Leopard is an just as update? Is there anyway to add the drive using Disk Utility and if so how do I do it?

My computer has been seen at Genius bar 6 times for freezing up, reloaded all original settings and even went to the apple shop where they replaced the battery and logic board. Still freezes after I try to reload iTunes stuff and app stuff from apple

my computer has been seen at Genius bar 6 times for freezing up, reloaded all original settings, all of their diagnostics, and they even sent it to the apple shop where they replaced the battery and logic board. Still freezes after I try to reload iTunes stuff and app stuff from apple, especially iPhoto which is seems to refuse to load and then begins freezing up all over again. Anyone else have this problem. Other than this, I have had absolutely no problems with this computer. Now, it's a file of junk.

Hi Ronald ...
Have you checked lately to see how much free space there is on the disk? Especially since iPhoto freezes at launch ...
Click your Apple menu icon top left in your screen. From the drop down menu click About This Mac > More Info > Storage
Make sure there's at least 15% free disk space.
And make sure the OS X software is up to date.
Click the Apple  top left in your screen.
From the drop down menu click: Software Update
If you have anti virus software installed or are using third party Mac cleaning utiliites, that may be part and parcel of the your problems.

How do I reinstall CS6 Extended 64-bit after replacing hard drive and OS?

How do I reinstall CS6 Extended 64-bit after replacing hard drive and Windows 7 64-bit OS?

You can download the trial installer directly. Find the appropriate link below.
You must be on a trial download page to use the links, otherwise you get an error message.
For example, load the following page: http://www.adobe.com/cfusion/tdrc/index.cfm?product=photoshop_elements&loc=us
before pasting the link into the address bar.
http://trials2.adobe.com/AdobeProducts/PHSP/13/win32/Photoshop_13_LS16.7z
http://trials2.adobe.com/AdobeProducts/PHSP/13/win32/Photoshop_13_LS16.exe
You need to kepp both files downloaded into same folder and after download click on .exe file to extract .7z

I deleted my back up files from my external hard drive and my trash won't empty. I get an error code -22. Can anyone tell me how to fix this?

I deleted my back up files from my external hard drive and my trash won't empty. I get an error code -22. Can anyone tell me how to fix this?

JLCruz wrote:
I deleted my back up files from my external hard drive ...
If this is related to Time Machine Backups...
See here > Should I delete old backups? If so, How?
From Here > http://pondini.org/TM/FAQ.html
If the TRASH still won’t Empty...
See Here > http://pondini.org/TM/E6.html

How to replace hard drive and transfer everything over?

I've looked everywhere but am unable to find a definitive guide on how to do this.
Currently I have an early 2011 MBP that came with Snow Leopard and upgraded to Lion later. It has an HDD and I want to replace it with an SSD and transfer everything over to the SSD. Considering Lion created a Recovery partition (and there is also an EFI partition), I'm confused on how to do this the best way to basically copy my current hard drive to the new SSD.
The best I've figured out is to connect the SSD with a SATA-USB cable, use the Lion Recovery Disk Assistant ( http://support.apple.com/kb/dl1433 ) to create a Recovery partition on the new SSD, then, booting into Recovery, install Lion on the new SSD, and then use Migration Assistant to transfer all my files over.
Is there a simpler or better-explained way to basically copy my current hard drive over to a new SSD and then remove the HDD and use the SSD?

How to replace or upgrade a drive in a laptop
Step One: Repair the Hard Drive and Permissions
Boot from your OS X Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Installer menu (Utilities menu for Tiger, Leopard or Snow Leopard.) After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer.
If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
Step Two: Remove the old drive and install the new drive. Place the old drive in an external USB enclosure. You can buy one at OWC who is also a good vendor for drives.
Step Three: Boot from the external drive. Restart the computer and after the chime press and hold down the OPTION key until the boot manager appears. Select the icon for the external drive then click on the downward pointing arrow button.
Step Four: New Hard Drive Preparation
1. Open Disk Utility in your Utilities folder.
2. After DU loads select your new hard drive (this is the entry with the mfgr.'s ID and size) from the left side list. Note the SMART status of the drive in DU's status area. If it does not say "Verified" then the drive is failing or has failed and will need replacing. Otherwise, click on the Partition tab in the DU main window.
3. Under the Volume Scheme heading set the number of partitions from the drop down menu to one. Set the format type to Mac OS Extended (Journaled.) Click on the Options button, set the partition scheme to GUID (for Intel Macs) or APM (for PPC Macs) then click on the OK button. Click on the Partition button and wait until the process has completed.
4. Select the volume you just created (this is the sub-entry under the drive entry) from the left side list. Click on the Erase tab in the DU main window.
5. Set the format type to Mac OS Extended (Journaled.) Click on the Options button, check the button for Zero Data and click on OK to return to the Erase window.
6. Click on the Erase button. The format process can take up to several hours depending upon the drive size.
Step Five: Clone the old drive to the new drive
1. Open Disk Utility from the Utilities folder.
2. Select the destination volume from the left side list.
3. Click on the Restore tab in the DU main window.
4. Check the box labeled Erase destination.
5. Select the destination volume from the left side list and drag it to the Destination entry field.
6. Select the source volume from the left side list and drag it to the Source entry field.
7. Double-check you got it right, then click on the Restore button.
Destination means the new internal drive. Source means the old external drive.
Step Six: Open the Startup Disk preferences and select the new internal volume. Click on the Restart button. You should boot from the new drive. Eject the external drive and disconnect it from the computer.

Replacing Hard Driver and RAM

Is it okay to replace the Internal Hard Drive and RAM at the same time? Also, once I replace the hardware how do I restore my last Time Capsule Backup to the new hard drive?

Hello Jason Castellani -Usually best to do one major change at a time in case something goes wrong. That said I can see where you are going here once you got your MBP apart. If you are a gambling man go for both, esp if you have done the procedures before and comfortable with the operation.
See this knowledge base article for your migration question.
http://support.apple.com/kb/HT1177
Hope this helps
Message was edited by: leroydouglas

G5 Tower, replaced hard drive and now can not get it to work- HELP

My G5 (tower) crashed hard & after a trip to the Genius Bar at my local Mac Store I found out the hard drive was dieing.
The Mac person fixed some problem files & told that I could replace the hard drive. I bought a 350 GB SATA 3.5in hard drive and placed it in the second slot in the tower. I then used time machine & backed up the hard drive to the second slot (after I backed up on an external hard drive- just to be safe).
I removed the hard drives & placed the new one in the A slot. When I turned on the computer I had the ? folder. I turned off & restarted holding the option key and got two folders, one with a turn back arrow & a rt facing arrow. Clicked either did nothing. Does any1 know what I am doing wrong?? If so please let me know. Much appreciated.

Did you reset your PRAM?
command-option- p-r
Hold down all four keys as the mac starts up and wait for the chimes to ring twice. Then let the machine start up as usual.
If it works be sure to check your date and time settings (the system will tell you)
You can also start up from your system disk holding down the c key as it starts-- go past the language screen and open disk utilities from the menu bar run disk repair and then repair permissions. Set your startup disk to your new drive.
Hopefully that will take care of the problem.

Just Replaced Hard Drive and Time Capsule Suddenly Almost Full

I just replaced my 200GB hard drive (with approx. 165GB used) with a 500GB hard drive. My Time Capsule now shows about 330GB in storage...about my original 165GB x 2. So, I'm thinking that I now have my 165GB from my old hard drive in storage, and the 165GB from my new hard drive.
My question is...how do I correct this?

Was this an internal drive that was replaced? If so, my guess would be that the Time Capsule sees this as a new computer and will backup the contents of the entire drive.
Open your Hard Drive and look for the SHARED heading on the left. Click the Time Capsule icon and a Time Capsule folder will appear in the window on the right. Double click this folder.
You should now see a xxxxx.sparesbundle file for each computer that has been backing up. The sparsebundle file contains the name of your Mac and MAC address. If you see the same listing twice, you will know that the TC has made a new complete backup of your computer.
I haven't experienced your situation first hand, so I'm not clear on whether you will be able to access the "old" backups from your "new" computer. That might be the subject of a new post if that is the case.

Replaced hard drive and getting error

start up failed hard disk smart 0301
and quick scan 0303
i have everything backed up on my external.... this is the 2nd time i replaced the hdd... the 1st time it was under warenty
i have a hp pavillion dv5 -1251nr
i also have the op cd.... it was running vista.... help because i made the mistake of getting a sony netbook and its done for... my only chance to have a working pc is this hp.... and i am going insane without one

Contact the vendor of the new hard drive and request an RMA. Sometimes hard disks are received and the fail right out of the box. The manufacturers and vendors are aware of that. That is always a great reason to keep a receipt.
****Please click on Accept As Solution if a suggestion solves your problem. It helps others facing the same problem to find a solution easily****
2015 Microsoft MVP - Windows Experience Consumer

Replaced hard drive and iTunes does not recognize my laptop

My 2011 MacBook Pro froze up and when I rebooted the folder error came up. Replaced hard drive with a SSD drive and my new OS has a new name. When I logged into ITunes I had to delete an account due to my limit being reached. My old Mac ID was showing and it was signed up for the cloud at a fee of $24.00. The same MacBook but with a new hard drive had a new ID and I can not restore any of my pics or ITunes music. Am I missing a step or can I rename my Mac so it will match my old ID? If I rename it can I download my old info off of ITunes?? Thanks

I'm not following much of the question and for me it would help to get some terms straight. You only "log into" the iTunes Store (online). What account was this and what limit??
Old Mac ID? Your AppleID is what you use to log into the store. It does not change with computers. You always use the same one, perhaps updating the email address from time to time.
By the cloud do you mean iTunes Match?
Sure, your computer hard drive has a new name (you can rename it -- my series of drives have kept the same name for 23 years now). That doesn't affect logging into the Store. Start up iTunes, log into the Store using your same Apple ID, download available past purchases, and if you have the Match service download your other music too. You may have to authorize the computer again. I don't know which part of the computer is used for authentication and if that got lost with the old drive.

Music on hard drive, replaced hard drive and now library won't match up

I put all my cd's on a hard drive (9000 or so songs) and had a hard drive failure, so I moved all the songs to a new hard drive and now I can't use the Itunes library to connect with that hard drive, except one song at at a time.
Is there any way to get these two to communicate?
David

Is the rest of your music located in a different folder? You'd need to know where those files are in order to add them to iTunes. If you're not sure of their location, try a Spotlight search. Are you not able to locate the files to add them to iTunes, or are you selecting them but they are not appearing in the iTunes library?
I have all the actual music files located on a external hard drive, but the itunes file name(s) are located on the computer. The problem started when I got a new computer and switched all the stuff over, and then got a new hard drive because the old one was making noises. I copied one hard drive directly over to the other and now am trying to connect the two so they talk together.
The fix you sent me semed to work great until I noticed that I did not have any music after the letter "a" (namely 1/36 of the music). I ried it again with another copy I had and lost that too. Now, I am working with the copy I had on the other computer, which doesn't have all the data, but does have most of it, and I can survive adding the other stuff later somehow by re-copying the music and getting the data over again, but I do want to somehow get the other 35 letters worth, if possible.
David Molony

I had to get a new hard drive and now iPhoto is gone. Can I get it back?

I had to replace my hard drive and now my iPhoto is gone. Is there a way to get it back?
Thanks

reinstall from the original source
Could be
1 - the restore disks that came with the computer - if it came with CDs and you do not know where they are then contact Apple to see if they can be replaced
or
2 - the iLife DVD that you purchased
or
3 - the app store - log in under the Apple id used to purchase the software or to set up the computer - look under purchases - you might have to unhide or accept the Application first
LN

Replaced Hard drive and logic board on ipod 5.5g...still get sad ipod HELP!

Similar Messages

Maybe you are looking for