Replaced motherboard and when I started the computer I get no boot screen

I have a HP media center m7463w. I am running Windows Vista Home Premium. My computer crashed and I replaced the power supply when I restarted I had a blank screen (not even a boot menu option), Therefore I felt that replacing the motherboard was the next thing to try, I put a used
Asus HP Compaq LGA775 motherboard 5188-5465 P5LP-LE
in and still got the same result (by the way I've replaced the motherboard once before and when I restarted I got the error message "No Operating System Found" and all I did was re-install Vista Prem. and had no problem until now.)
The only message I receive is from the monitor telling me no signal detected (DVI or VGA) and the monitor was going into sleep mode. I know that the first thing that comes to mind is that the graphics card is bad. My wife also has a HP Media center m7760n which is basically the same computer also running Windows Vista Home Premium. So I've switched monitors and put my graphics card into her computer and they work fine.
I've tried HP's resetting the BIOS even when you have no picture. I've replaced the CMOS battery after leaving the battery socket empty with nothing attached to the computer for 10 hours. And lastly I have removed and reset the pin in order to clear the CMOS. By the way when the problem first appeared I DID put in my recovery disc and restart. The CD/DVD drive is working. HELP!!!

Did the computer technician identify what the issue was in this case?
↙-----------How do I give Kudos?| How do I mark a post as Solved? ----------------↓

Similar Messages

When starting the computer, I get a grey screen and following status: your startup disk is full. How can I still enter (in order to free-up some space)?

When starting the computer, I get a grey screen and following status: your startup disk is full. How can I still enter (in order to free-up some space)?

Simple way to make HDD free space is delete files you don't need anymore.
Or get bigger drive and external HDD case, then:
1) install bigger HDD in external drive case.
2) connect external drive and format and mount it with Disk Utility.
3) make clone with Carbon Copy Cloner or SuperDuper!(source drive is internal HDD, target drive is external one).
4) install external bigger drive into your Macbook Pro.
In the cace if your're using Mac Pro:
1) get bigger HDD and install it in drive bay of Mac Pro.
2) format and mount it with Disk Utility.
3) make clone with Carbon Copy Cloner or SuperDuper!(source drive is old HDD, target drive is new one).
4) Select boot drive to new bigger one.

Ive just upgraded my late 2009 macbook, and things are not working properly. First of all, when I started the computer first time after installing Mountain Lion, some message advised me that some files were impossible to install.

Ive just upgraded my late 2009 macbook, and things are not working properly. First of all, when I started the computer first time after installing Mountain Lion, some message advised me that some files were impossible to install. Once I wrote my password, and for now on, everytime I start the session, another window advise me that "Java SE 6" is missing, due that, the computer can't run some "CS5Service Manager". If I try to install it, the download ends with an error. If finally, you skip the istallation, you arrive to the dock, but the menu bar at the top of the screen doesn't show up.
In addition, my trackpad doesn't works either. I can move the arrow but i can't click anywhere, probably because the option of clicking by touching is disabeled and I can't performance a regular click.
I'll be very glad if someone know what the heck is happening with my computer. Anyway, I'm going to the genius bar next Saturday. Thx!

We're sorry.
We can't find the article you're looking for.
Please return to the Apple Support homepage.
Sigh.

After installing Itunes 10.6.3 When ever I start the computer I get a pop up the says "Applesyncnotifier.exe- unable to locate component, this application has failed to start because Corefoundation.dll was not found" How can I get rid of the pop up?

After installing Itunes 10.6.3 When ever I start the computer I get a pop up the says "Applesyncnotifier.exe- unable to locate component, this application has failed to start because Corefoundation.dll was not found" How can I get rid of the pop up?

I hope it doesn't effect how I down load my itunes to my ipod and iphone.
No you should be fine. (The MobileMe service is being shut down, anyway, so there should be no impact at all.)

When I start the computer I warning message flashes but I can't see what it says

When I start the computer I warning message flashes but I can't see what it says

With Windows Explorer, navigate to your C:\Program Files\Common Files\Apple\Apple Application Support folder.
Copy the libxml2.dll that you should find there, navigate to the nearby Mobile Device Support folder, and Paste it in there also.
Restart the programme all should be well
In case that your OS is (64 bit)
1. Open windows explorer, go to location C:\Program Files (x86)\Common Files\Apple\Apple Application Support
2. Copy file "libxml2.dll"
3. Open new windows explorer, to to location C:\Program Files (x86)\Common Files\Apple\Mobile Device Support
4. Paste file "libxml2.dll" to the location.
5. Restart the programme, it should not display that message, it should be clear.
Good Luck

I get this message when i start the computer :" error : unable to start the bluetooth stack service"

i get this message when i start the computer :" error : unable to start the bluetooth stack service"

If a power cycle of the TC works then the issue is simply Lion.. and there is as yet no fix.. and may never be..
Apple do not seem to acknowledge the issue but plenty of people have it.. It doesn't happen with SL.. one very good reason to not bother with Lion.. Maybe ML will fix it.. without Apple having to ever admit an issue.
In the meantime, if possible downgrade TC to 7.5.2 .. it has less issues than 7.6 or later.
Reset the TC and change all names, TC and wireless names, to short, no spaces, no special characters.
If it is the main router, set the dhcp lease to a short time.. 10min I recommend.
The above will probably not fix the issue.. but it might go a bit longer before a reboot is needed.. going back to SL would fix it.

I cannot turn on my ipod touch. the apple logo appears but does nothing after and when connected to the computer, it is nor recognize. what's the solution for this?

how to fix ipod touch if it hungs/ does not turn on and stays only on the apple logo when you press/hold the keys home and sleep/wake. and when connected to the computer, it does not appear in the itunes that the ipod is connected or simply the computer does not recognize the device. i barely need you help guys! please...

I found this possible solution on another support thread, so I tried it.
turn off iPod
hold Sleep and Home buttons to start it.
When Apple appears, let go of Sleep button, but keep holding Home button.
When screen goes blank, let go of Home button.
Connect cable and check iTunes to see if it has conencted.
This did not work for me.
I then turned off the iPod, restarted the Mac, and restarted the iPod normally.
I connected them with the cable, and it works like normal. :-)

I have a DVD I recorded from my tv. I am trying to make copies and when I insert the DVD I get a message saying it is blank even though it is not. My question are: Why does my computer think it's blank? And how can I copy a DVD?

I have a DVD I recorded from my tv. I am trying to make copies and when I insert the DVD, I get a message saying the DVD is blank, which it is not. My questions are: Why does my computer think it's blank? And how can I copy the DVD providing my computer recognizes there is content on it?
Thanks, Sheila

TV video typically is copyrighted content. We'd be breaking several rules trying to help you. Good luck!

PC went south. Geeks brought it back. PS elements and premier 11 can't start. Error msg sez configuration incorrect needs to be reinstalled. When I load the disk I get a blank screen. Try to uninstall and can't find apps i control panel. How can I get the

PC went south. Geeks brought it back. PS elements and premier 11 can't start. Error msg sez configuration incorrect needs to be reinstalled. When I load the disk I get a blank screen. Try to uninstall and can't find apps i control panel. How can I get the apps back?

adobeamatuer
Thanks for the reply.
Although the security of Windows XP SP3 32 bit is compromised by Microsoft no longer supporting XP, if Windows XP was restored as claimed, you should still be able to install/uninstall Premiere Elements versions of it that you did before the Microsoft support removal.
I think a revisit to the Geeks would be in order. It may be that they could not restore Windows XP because of the Microsoft non support. I would take along the Premiere Elements installation disks so that you do not leave there without actually seeing Premiere Elements (or a non Adobe program) running on your restored Windows XP. What was the other software that you tried to use that did not work?
Please update us on your progress when you get a chance.
Best wishes
Thanks.
ATR
Add On...spelling correct 12 03 2014.

Downloaded mt lion on my iMac, now when i start the computer my outlook email automatically opens. When I right click on the mail icon it isn't checked to open on startup. How do i correct this

downloaded mt lion on my iMac, now when i start the computer my outlook email automatically opens. When I right click on the mail icon it isn't checked to open on startup. How do i correct this

This is probabaly caused by the resume feature. When you log out, uncheck the box that appears.

I am unable to update an app, Chirps! USA. I have tried both wireless and when connected to the computer. I contacted the company and they said it was an iTunes problem. ANy suggestions?

I am unable to update an app, Chirps! USA. I have tried both wireless and when connected to the computer. I contacted the company and they said it was an iTunes problem. ANy suggestions?

Hi..
Delete the app then reinstall.
Hold the app icon down until all the apps jiggle then tap the x then tap Delete. Press the Home button once or twice to stop the jiggling.
Then go to the iTunes store and re download the app.
Downloading past purchases from the App Store, iBookstore, and iTunes Store
That should download the most recent version including whatever update was available.
You won't be charged again.

When starting the computer I get the dong but then it stops with three loud beeps as the light in the front flashes in line with the beeps. The beeps repeat till switching off

When starting the computer I get the dong but then it stops with three loud beeps as the light in the front flashes in line with the beeps. The beeps repeat till switching off

Check out this Apple support article https://support.apple.com/kb/HT1547

Somehow, all of my exe files are tagged as Acrobat files - I cannot run any of the software on my computer - when I start the computer none of the startup programs run because they all try to open in acrobat.

Somehow, all of my exe files are tagged as Acrobat files - I cannot run any of the software on my computer - when I start the computer none of the startup programs run because they all try to open in acrobat.

See if anything in here helps: https://helpx.adobe.com/acrobat/kb/application-file-icons-change-acrobat.html

When I start my computer I get a "AppleSyncNotifier.exe Entry Point Not Found message. I also get an error message when trying to sync with iTunes that a backup session cannot be started. How do I fix this?

In the last few days when I start my computer, I get a box that opens with "AppleSyncNotifier.exe" Entry Point Not Found in the title.
It says: "The procedure entry point sqlite3_wal_checkpoint could not be located in the dynamic link library SQlite3.dll.
I have tried uninstalling and reinstalling iTunes and still get an error message when trying to sync my phone with iTunes
"iTunes could not back up iPhone ####, because a session could not be started with the iPhone."
The last time I tried to sync my phone (iPhone 3G S) with iTunes, everything seemed to freeze up at Stage 4 of the sync process.
Any advice????

With Windows Explorer, navigate to your C:\Program Files\Common Files\Apple\Apple Application Support folder.
Copy the SQLite3.dll that you should find there, navigate to the nearby Mobile Device Support folder, and Paste it in there also.
Reboot and see if all is well
In case that your OS is Windows 7 (64 bit)
1. Open windows explorer, go to location C:\Program Files (x86)\Common Files\Apple\Apple Application Support
2. Copy file "SQLite3.dll"
3. Open new windows explorer, to to location C:\Program Files (x86)\Common Files\Apple\Mobile Device Support
4. Paste file "SQLite3.dll" to the location.
5. Reboot your computer, it should not display that message, it should be clear.
Good Luck

I have updated my computer to windows 8 and when i connect my computer to get an app from itunes am getting will install can u plese tell me how can i rectify

hi
i have updated my computer to windows 8 and when i connect my computer to get an app from itunes am getting will install can u plese tell me how can i rectify

You will need to do it using a third-party utility such as Phone to PC. Also, see:
How to dowload purchased music
Downloading past purchases from the App Store, iBookstore, and iTunes Store

Replaced motherboard and when I started the computer I get no boot screen

Similar Messages

Maybe you are looking for