Replaced N96 restarting

Hi, I too have a problem with my N96 which keeps restarting (every 20' if idle, every 5-10' if I try to use it, e.g. get directions, listen to music or make a phonecall).
I returned it to Nokia freepost 3 times, it was sent back without being repaired. After a few angry phonecalls I sent it back a 4th time and it was replaced with another N96 from their repair stock.That too kept restarting BEFORE I MOVED ANY OF MY CONTACTS OR SETTINGS TO IT. Sent it back again, third phone arrived and that too restarts!
I have updated the firmware to 30.033, done hard and soft restarts, removed battery for 5', spoke to Nokia care centre, nothing seems to help...
Is there hope, or shall I just bin it and get an iPhone?
Note that all replacement phones sent by Nokia are not new, but are phones other people found unacceptable and had replaced.
Any suggestions / help greatly appreciated.

I should say, the handsets they sent back out have been "repaired" in the sense that they've been looked at, had parts replaced etc. and are only sent out when they meet certain standards. It's just that for some of the reverse logistics firms those standards aren't, shall we say, fantastic.
I don't think A-Novo have any real brand new stock to send out: they do tend to have old phone kits lying around (without the phone itself) but those aren't new either.
Help I'm trapped in a sig factory.

Similar Messages

N96 restarts, hangs and crashes. Not seeing USB

Hi, I got an N96 two months ago, it worked great, no problems, until about a week ago.
One night I wasn't able to charge the phone because I wasn't home. The phone was dying, so I put it off. The next morning, I plug it in and it barely resopnded. At first it would show the white screen for a second before dying again. I left it plugged for a few hours assuming the battery was really flat. It never came on, or charged.
The next day I took it to a Nokia Store, assuming it was the battery. The customer care staff refused to replace it, saying that it was just flat, and worked in another phone. I found this odd, but took it back home, where it was suddenly working.
Problem is, since then, the phone randomly dies. If i place it on the table, chances are it would go off. This was immensely irritating, and I had to start handling it like an egg. After a few days, these subsided. This morning, however, I tried to plug the USB into my pc, and it wouldn't respond.
A couple of seconds later it died. Every attempt to put it back on afterwards resulted in the phone coming on, hanging for some seconds, then going off aagain. I plugged into the charger, and it came on... but then it would go off again and restart.
I eventually solved this by removing the sim card, hoping to back up my data and reset the phone. Problem is, now I can't still get the phone or the pc to realise the USB cable is connected.
What's going on. What do I do?

It sounds like the phone is damaged, and the nokia shop should repair the handset (you get a 6month warranty for the battery!).
If the usb is the only problem, you can attempt to back up the phone memory content to a memory card, this wont allow you to backup the mass memory (you wil either need to get bluetoth or usb to work for that).
IF you have a micro sd memory card, place it into the handset and open up the file manager application, slect backup and backup your phones content.
Any applications you have installed to the mass memory will have to be backed up another way, you can transfer the content to the memory card, but it really depends on the capacity of the memory card and how much data is in the mass memory.
Once you have done this, you should be safe to say that you can wipe the handset or give it to nokia to tinker with. I doubt wiping the handset wil solve the problem as it sounds quite severe - moan at nokia and im sure they wil fix it pronto!
To wipe your handset (But not your mass memory/memorycard/simcard) turn your phone off, then whilst you are turning it on hold down the GREEN (call key) AND Star (bottom left) key AND the number 3 all at the same time. Hold them down until you are greeted with the nokia tone, if it worked then you should be asked to set your location, otherwise do it again but quicker.
But as i said, give it to nokia as the handset sounds faulty, very faulty.
Hope this helps,
Tony

My N96 restarts automatically

I bought a brand new Nokia N96 few weeks ago, but my handset restarts automatically, i want to know what could be the problem! the software version of my phone is version 30.******. I can't use it properly! I waste money and i am not satisfied with it!

Random restarts are not symptomatic of an N96 running v30
Suggestions
1) Pull any memory card you may have inserted, does the problem still occur with no memory card in the phone
2) have you installed any apps to the c drive, perhaps moving some to the e may help, perhaps an unstable app is causing your problem
3) Have you tried a hard reset
Also is your phone a branded model (Voda ???)

Nokia N96 restarts while using Gps, Google Maps an...

Hi guys, I've got this problem with my n96. When I try to use Nokia maps or Google maps, it restarts automatically. Last month I updated the firmware to 30.033. It was working fine before update, I had no problem with nokia and google maps, but after that update to firmware it randomly restarts. Any help would be highly appreciated.

The problem of phones restarting following a firmware update can usually be resolved by resetting the phone.
Always remember to backup your phone before performing resets as your data may be lost.
First try this,
*#7370# - Reformat your phone
If it doesn't work then try this.
Then try the "3 finger deep reset". With the phone powered off, depress and hold these three keys simultaneously "*" "3" "green phone" and then power on phone using the on/off button whilst keeping all four keys depressed until you hear start-up tone.
This should ONLY be done if the device doesn't power up normally anymore and it wipes everything in the Phone memory that is not part of the ROM.

Droid 3 Replacement issues

i am on my 10th replacment
issues
restarting, randomly
not calling when i hit call - that makes me the maddest -
camera doestn work
microphone didnt work ( could only talk on speaker phone )
touchscreen didnt work

statman wrote:
Droid 3 Camera issues I am running into:
- - First - If I can start the camera without it causing the phone to crash.... (how do you disable the "Droid" sound on reboot - getting VERY annoying)
Try Settings / Applications / Manage Applications / All Tab / Camera / Clear Data to resolve camera issue.... To disable startup sound try disabling Settings / Sounds / SD Mount or something along this.
- - I have to use a task killer to keep the camera from burning up the battery after using it. - WHY????
I understand where you coming from but I would use System Panel instead of a task killer, a number of users helped me see the light of not using a task killer.
- - I bought my phone to keep in touch via skype with my son @ college - but now learn that the droid 3, with it's front facing camera DOES NOT WORK - (not on the Verizon-specific Skype - what a lame app), but using the real Skype app... on a video chat, the Droid gives a black screen, not my image. ??? From what I see online, same response from other video chat tools. This was one of the biggest selling points for me!!! Am more than mildly annoyed at this one.
That strange because the Droid 3 is supported on Skype's site.
Previous phone was a Droid 2 - with none of these problems.... appears that the Droid3 was released before testing and fixing issues.
PLEASE ADDRESS THIS!!!

IPhone quits in mid-conversation, won't restart, shows Apple logo.

My 2008 iPhone 3g has quit on my twice today, both times in mid conversation.
The phone shows the silver Apple startup logo, but won't get past that to boot up.
I tried the hard reset (Home + top buttons at the same time), and the first time it powered the phone down, but the second time it wouldn't even do that.
I even powered it off, removed the SIM, replaced and restarted, but it didn't do anything.
The last time, in frustration I shook the phone and it cam back to life, but that may point to the accelerometers being screwed. Does anyone know of any way I can get a diagnostic to find out what's going on?
Another weird symptom is after the last reboot (hard reboot) my wallpaper disappeared, and I can't replace it.
One further piece of information: I normally use my iPhone with the supplied earbuds and microphone, for hands-free usage. Makes it safer to answer the phone in the car. The phone jack boot has become worn and split over time, and I've jury-rigged a new stress relief boot by using a rubber band wrapped around the existing jack housing and boot. I'm wondering if there could be a short happening in this jury-rig that might be causing the symptoms.
Anybody got any insights?

Well, it seems as though you answered your own question. While it is apparent the phone has an issue, since it is out of warranty, Apple will not replace it, except under their out of warranty replacement policy, which is the $199 they quoted you, and that is for a refurbished phone. The only other option I'm aware of it to try and force it to restore, read this article: http://support.apple.com/kb/HT1808
Since you are not willing to do the out of warranty replacement, which I can understand given the possible introduction of a new handset in the near future, if the article I linked for you doesn't work, you may have to live with a different phone for a short time.

N96 wont shut up

I've recently received a replacement N96 from vodafone but unfortunately I cannot seem to stop this one from talking to me. It reads out everything that is visible on the phones screen.
Someone managed to turn this voice off for me but when I turned the phone had been off and then back on the voice was back.
Can someone please tell me how I can resolve this issue and turn the voice off completely???
Any help would be much appreciated!!!

Yes i have !!!!!
Would you know which specific setting this would be as i have tried them all and i cant turn this voice / narrator off?

Cannot sync. Error message says "sync session failed to start"

I am not able to sync my ipod. The error message "the ipod could not be synced because the sync session failed to start" keeps popping up. I have tried both syncing it plugged in and by wifi and the same message appears

Same problem today. Took five times to reinstall without any error messages. Apple has posted a way to fix and you should follow their's first. I finally got to upldate correctly by doing their fix but with one difference. I did the following:
1) Went to the C:\program files (x86)\iTunes and C:\program files\iTunes folders and moved every file ending in .dll to the desktop (even if two files in same location had the same name, just replace)
2) Restarted computer and still got error message
3) Uninstalled all apple programs possible in the following order......itunes, apples software update, apple mobile device support, bonjour, and apple application support.....all performed using the microsoft control panel
4) put all the .dll files on the desktop in the trash and emptied (this is a step apple support did not specifically put in their fix but for a final try I wanted to delete everything apple).
5) Restarted computer.
6) Re-installed itunes from apple website
No error messages during re-install and was able to open shortcut in one try. Even updated my ipad to make sure everything was working.

Error when try to schedule a Webi Report

Good day every one:
Can anyone please help me to solve this problem??? the issue is this, I want to schedule a Webi report but when i clic on Schedule and go to Format and Destinations tab, i got this message:
displayErrorMessage="VIEWER:VIEWER_ERR_DEFAULT (Error: INF )"; traceErrorMessage="\u003Cinput type="hidden" name="BENCHERROR" value="Error Number : - Error Description : VIEWER:_VIEWER_ERR_DEFAULT"\u003E";
And i can not see the formats availables to schedule the report and of course i can not see the configuration and destinations options.
Looking for an answer i found this:
http://forums.sdn.sap.com/thread.jspa?threadID=1537527
but that is an old post and i can not find the file mentioned there, can somebody please help me to fix this???
We are using:
BOBJ 3.1 SP3
Windows Server 2003
32 bits
Regards

I just found this
I was able to fix the issue by replacing the webiviewer.properties file with the file from the WARFILES\WEBAPPS directory. The webiviewer.properties file looks like it was corrupt as there was only 1 line in the file. After replacing and restarting the servers there's no longer an error when selecting Formats & Destinations.
I checked those webiviewer.properties and like you , one of them had only 1 line, about the language.
So I replace the one from Tomcat55\webapps\AnalyticalReporting\WEB-INF\classes with the one in the folder Tomcat55\webapps\AnalyticalReporting\classes
My guess is that this properties is corrupted because of the installation of other language. What should be done is updating the file with the new language parameters but what is done is a replace of the file.
I foun that in this link
http://www.forumtopics.com/busobj/viewtopic.php?t=150796&sid=bad10669f42c6de2b77e37b03122334d
I will apply this and if im success i let you know
Regards
Edited by: Elio Javier Guzman Hernandez on Oct 21, 2011 6:25 PM
Well the solution that i gave you works fine.
Regardas
Edited by: Elio Javier Guzman Hernandez on Oct 21, 2011 10:42 PM

Hello, I have windows 7, Im getting msvcr80.dll error 7(windows error 126) when I tried to update my itunes. Now it won't open. Does anyone have a remedy? And when I try to uninstall it says that the file cant be found.

Hello< I have windows 7, I tried to install the new itunes version, last night 1/30/14, Im getting msvcr80.dll error 7 (windows error 126). Does anyone have a remedy for this? When I try to uninstall the ituned program it says it can't be found and to make sure I have permission to uninstall.

Same problem today. Took five times to reinstall without any error messages. I did the following:
1) Went to the C:\program files (x86)\iTunes and C:\program files\iTunes folders and moved every file ending in .dll to the desktop (even if two files in same location had the same name, just replaced)
2) Restarted computer and still got error message
3) Uninstalled all apple programs possible in the following order......itunes, apples software update, apple mobile device support, bonjour, and apple application support.....all performed using the microsoft control panel
4) put all the .dll files on the desktop in the trash and emptied (this is a step apple support did not recomment in their posted solutions but for a final try I wanted to delete everything apple).
5) Restarted computer.
6) Re-installed itunes from apple website
No error messages during re-install and was able to open shortcut in one try.

My iTunes will not start. The box on the error message APSDaemon.exe, And message says "This application failed to start because MSVC80.dll was not found. Reinstalling may fix." I did the reinstall and I get the same error.

My iTunes will not start. The box on the error message APSDaemon.exe, And message says "This application failed to start because MSVC80.dll was not found. Reinstalling may fix." I did the reinstall and I get the same error. The error first happened after I approved the an iTurns update.

Same problem today. Took five times to reinstall without any error messages. Apple has posted a way to fix and you should follow their's first. I finally got to upldate correctly by doing their fix but with one difference. I did the following:
1) Went to the C:\program files (x86)\iTunes and C:\program files\iTunes folders and moved every file ending in .dll to the desktop (even if two files in same location had the same name, just replace)
2) Restarted computer and still got error message
3) Uninstalled all apple programs possible in the following order......itunes, apples software update, apple mobile device support, bonjour, and apple application support.....all performed using the microsoft control panel
4) put all the .dll files on the desktop in the trash and emptied (this is a step apple support did not specifically put in their fix but for a final try I wanted to delete everything apple).
5) Restarted computer.
6) Re-installed itunes from apple website
No error messages during re-install and was able to open shortcut in one try. Even updated my ipad to make sure everything was working.

CC&B v2.3.1 Integration Configuration Issue

Hello all.
We're working on implementing the configuration for CC&B v2.3.1 for integration with AIA. However, we have been unable to successfully place any message to the AIA JMS queue. Our CC&B and AIA resides in 2 different servers.
We're using Weblogic 10.2 MP2, and JDK 1.5.0_21.
Based on the research I’ve done so far, it seems to be a problem with a Java security policy. And the recommendation was to add the following line to java.policy ==> permission javax.management.MBeanTrustPermission "register". I tried this. However, the error message did not change.
I hope the experts in this group will be able to help me resolve this problem.
These are the error messages that were logged when the Weblogic server was started.
myserver.log, weblogic_current.log, wl-domain.log
- ####<Nov 29, 2010 8:53:20 PM EST> <Error> <WebLogicServer> <ouccb01.solutionworks.com> <myserver> <[ACTIVE] ExecuteThread: '1' for queue: 'weblogic.kernel.Default (self-tuning)'> <<WLS Kernel>> <> <> <1291082000425> <BEA-000297> <Inconsistent security configuration, java.security.cert.CertificateParsingException: PKIX: Unsupported OID in the AlgorithmIdentifier object: 1.2.840.113549.1.1.11>
####<Nov 29, 2010 8:53:20 PM EST> <Emergency> <Security> <ouccb01.solutionworks.com> <myserver> <[ACTIVE] ExecuteThread: '1' for queue: 'weblogic.kernel.Default (self-tuning)'> <<WLS Kernel>> <> <> <1291082000426> <BEA-090034> <Not listening for SSL, java.io.IOException: PKIX: Unsupported OID in the AlgorithmIdentifier object: 1.2.840.113549.1.1.11.>
- <Nov 29, 2010 8:53:20 PM EST> <Error> <WebLogicServer> <BEA-000297> <Inconsistent security configuration, java.security.cert.CertificateParsingException: PKIX: Unsupported OID in the AlgorithmIdentifier object: 1.2.840.113549.1.1.11>
<Nov 29, 2010 8:53:20 PM EST> <Emergency> <Security> <BEA-090034> <Not listening for SSL, java.io.IOException: PKIX: Unsupported OID in the AlgorithmIdentifier object: 1.2.840.113549.1.1.11.>
These are the error messages that were logged when we run the F1-SYNRQ batch job to faciliate the SP Sync Up
threadpoolworker log, F1-SYNRQ log
- 2010-11-29 21:06:51,270 [Thread-74:WorkProcessor$WorkRunner(WorkProcessor$WorkRunner:6628401a-f726-44fd-8bb9-372d31eee721)] ERROR (support.management.ManagementRegistrar) Unable to register MBean:spl.fw:service=BatchJob_F1-SYNRQ_0.1919 due to java.security.AccessControlException: access denied (javax.management.MBeanTrustPermission register)
- 2010-11-29 21:06:52,339 [Thread-12:WorkProcessor$WorkRunner(WorkProcessor$WorkRunner:f84dd719-e40e-4270-9a31-e519c5e37800)] ERROR (support.management.ManagementRegistrar) Unable to register MBean:spl.fw:service=BatchThread_F1-SYNRQ_1_of_1.35 due to java.security.AccessControlException: access denied (javax.management.MBeanTrustPermission register)
- weblogic.messaging.dispatcher.DispatcherException: Could not register a DisconnectListener for [Delegate(168736533) [weblogic.iiop.IOR[RMI:weblogic.messaging.dispatcher.DispatcherImpl:0000000000000000] @127.0.0.1:47097, <0, null>]] for weblogic.jms.C:ouccb01.solutionworks.com:up0:z33sj0vqj85k

Hi i'm not sure if you have solved this, but here is a resolution:
We followed the instructions and built the server with the correct version of pre-requisites, including jdk1.5.0_21 and jrockit-R27.5.0-jdk1.5.0_14. When the application started the WebLogic processes were looking to use an MD5withRSA algorithm that is no longer supported by either Solaris 10 or Verisign. You may find that the OS you are using is different, but replacing the cert with an older cert from a previous version of JDK did the trick.
The system was using a cacerts file located located in 'jdk1.5.0_21/jre/lib/security' folder and was unable to register the certificate due to the algorithms not being supported.
We did some investigation of why this might be and found many people having the same issues. The resulted solution was to locate a demo certification that was compatible. So we renamed the current jdk1.5.0_21/lib/security/cacerts file to cacerts.save and copied in the jrockit-R27.5.0-jdk1.5.0_14/lib/security/cacerts file as a replacement. Restarted all of the environments and now Https is operational.
So in fact we replaced a newer version of JDK's jre security file with an older one, this fixed the problem.
Thanks,
Trevor

PowerMac 8600/250 LCD connection problem

I've an 8600/250 with a Sonnet Crescendo G4 processor upgrade; Sonnet Tempo ATA133 card; USB (v.1.1.2) card w/2 HDs--running both the native 4 gb scsi and a Seagate ATA/128 gb drives. It's all connected to a ViewSonic VX-710 15 inch LCD monitor. It is not internet connected. Of concern, a recent problem has arisen with the monitor connection. I've developed a thin white line that vertically extends down the face of the monitor adjacent the mouse scrolling marker. The line "moves" with the mouse scroll (a constant 1/2 inch relationship). Changing the monitor DPI setting to (1024X768--74.9mghz) will shorten the vertical length of the line to half the distance down the page. I'm using the analog connection with the monitor. Everything worked fine until very recently--the evolution of the line erratically developing over a few short days. The monitor, functions perfectly when hooked up as a second to my I-Mac, so I've ruled the monitor out as being faulty. Any ideas out there? VRAM memory issues? Would an ATA Rage 1280 video card installation help? I've grown rather fond of this useful, adaptive, tough little machine and it's reliability over the years. I use the computer as a dedicated platform for storage and management of years of my old OS 9.1 files and OS specific programs. I'm open to any and all suggestions.
Thanks,TMc

The long and winding road...
Voila!...it's working again. First of all, I want to thank everyone for their time and input--I tried it all. The final equation to the problem; stock VRAM.
Frustrated to no end, I wandered through the door of "Mc2", a local Mac shop (20+ years) in the nearby northern Monterey coastal burg of Soquel, CA. The shop always keeps a few older Mac's of various releases in the back for bits & pieces salvaging along with a couple of grey-hair techies who've been through it all.
The first thing asked was whether the "line" I was experiencing on the desktop had been accompanied by gradual pixel degradation over a a number of startups--it had! He responded by stating on the 85/86/9600 series motherboards VRAM serve as a through-put point, regardless of the Video card installed. He suggested "A faulty chip, especially with newer LCD monitors, will often manifest itself with a vertical line down the monitor." Additionally, he suggested this problem can also be confused as an indicator of a faulty LCD screen, BUT if the line moves with the mouse scroll or can be changed by pixel resolution/screen refresh rates, it suggests faulty VRAM--memory that should to be left in these machines for video stability. He suggested they should not be mixed and matched and need to be replaced in matching pairs.
A quick online over-night order to my trusty memory source "4AllMemory" (an excellent and reliable source for on-the-cheap new goodies for PCI macs), and Voila! With a little testing as to which chip(s) required replacement, I restarted and everything returned to normal. Relief, finally!

Anyone out there have an idea on how to solve an "Empty print file!" error?

I am trying print to a Lexmark C543 network printer from a PowerPC G5 (running 10.5.7). Prior to receiving the error message (Empty print file!) the print queue displays the following messages: “Looking for Lexmark C543” and then “The printer is now on-line”.
Now there is a twist, I can successfully print test pages, pdf files (only using Adobe Reader 9.1.2, not the Apple Preview application), and image files (only using Adobe Lightroom 2.4, not the Apple Preview application). If I try and print a webpage using Safari (4.0.1) or Word document using Word:MAC 2008 version 12.1.9 it will error out, unless I print it to a PDF and then reopen the file via Adobe Reader.
Here are the actions I have already tried, and didn’t work?
- Removed and installed printer (both via GUI and CUPS)
- Reset printer system
- Verify Disk (no problems found)
- Repaired Disk Permissions
- Removed/renamed all files I could find in Library and System relating to C543
- Downloaded and installed new driver
- Called Lexmark, “3rd Level support looked at the issue and the log and they concluded that it's a problem with the OS.”
Below is an excerpt from the CUPS error log that might shed some further light on the subject.
I [29/Jun/2009:10:59:44 -0400] [Job 6] Started filter /usr/libexec/cups/filter/cgpdftops (PID 205)
I [29/Jun/2009:10:59:44 -0400] [Job 6] Started filter /usr/libexec/cups/filter/pstops (PID 206)
I [29/Jun/2009:10:59:44 -0400] [Job 6] Started backend /usr/libexec/cups/backend/mdns (PID 207)
E [29/Jun/2009:11:00:11 -0400] PID 206 (/usr/libexec/cups/filter/pstops) stopped with status 1!
I [29/Jun/2009:11:00:11 -0400] Hint: Try setting the LogLevel to "debug" to find out more.
E [29/Jun/2009:11:00:11 -0400] PID 205 (/usr/libexec/cups/filter/cgpdftops) crashed on signal 10!
I [29/Jun/2009:11:00:11 -0400] Hint: Try setting the LogLevel to "debug" to find out more.
E [29/Jun/2009:11:00:11 -0400] [Job 6] Empty print file!
E [29/Jun/2009:11:00:14 -0400] PID 207 (/usr/libexec/cups/backend/mdns) stopped with status 1!
I [29/Jun/2009:11:00:14 -0400] Hint: Try setting the LogLevel to "debug" to find out more.
I [29/Jun/2009:11:00:14 -0400] [Job 6] Backend returned status 1 (failed)
I [29/Jun/2009:11:00:14 -0400] Saving printers.conf...

PaHu,
Thank you for welcoming me to Apple Discussions as well as explaining what you saw in the log.
I downloaded and ran the 10.5.7 Combo updater, but unfortunately it did not resolve my empty print file error.
Print Therapy (version 6.0.5) you suggested (and I downloaded) looked very promising. Unfortunately it too did not resolve my empty print file error. I have included the Print Therapy log below in hopes it will shed more light on the problem. The Print Therapy log stated: "You may need to reinstall OS X to resolve your printing issues." I am assuming this is probably because of the three missing files/directories it found.
Please let me know what my next steps should be, and if I should reinstall Leopard. If I have to reinstall Leopard is it possible to just install on top of the existing version without loosing or destroying the files (documents, images, etc.) we created?
Thanks again for all your help!
Brian
###Permission Repairs###
Starting permission verification and repair, omitting localized files...
The file /private/var/run/cups/certs/0 is missing!
The owner setting for the file /Library/Printers/InstalledPrinters.plist is incorrect!
It is 501, but should be 0
Repaired.
The directory /var/db/lockdown/Library is missing!
The directory /var/db/lockdown/Library/Printers is missing!
The directory /var/db/lockdown/Library/Preferences is missing!
The permissions for the directory /Users/Beth/Library are incorrect!
They are drwxr-xr-x, but should be drwx------
Repaired.
Recreating symbolic links...
Done.
Verification complete.
1624 files examined. 2 permission problems were found and repaired. It is recommended that you verify the permissions again to make sure the values are correct.
4 missing files/directories found during the verification process. They may be responsible for certain printing problems. Print Therapy cannot replace these items. Please refer to the log file for a list of the missing files/directories. You may need to reinstall OS X to resolve your printing issues. Certain files and directories are deleted when using the Reset Printing System option. These files and directories, if required, will be recreated during normal printing.
*******************Restarted Computer and re-added printer (test print failed, same problem)*******
###Temp & Prefs###
Starting /private/tmp directory and /tmp symbolic link permission verification...
Verification complete.
No problems found with the /private/tmp directory and /tmp symbolic link permissions.
Begin deleting temporary files for all users...
Temporary files for all users deleted successfully.
###CUPS Tools###
Stopping the the cupsd process...
The cupsd process has been successfully stopped. Please note that printing and/or adding printers with the Print & Fax System Preferences pane will not be possible until the cupsd process is running again.
Deleting the contents of the /private/var/spool/cups directory...
4 file(s) deleted from the /private/var/spool/cups/cache and /private/var/spool/cups/tmp directories.
Creating a new cupsd.conf file...
The cupsd process has been successfully started.
The cupsd.conf file was successfully replaced.
*******************Restarted Computer (test print failed, same problem)*******
###System Users###
Verifying root user attributes...
The information for the root user appears to be valid.
Verifying Printing Services user attributes...
The information for the Printing Services user appears to be valid.
Verifying Print Operators group attributes...
The information for the Print Operators group appears to be valid.
###Reset & Backup####
Begin resetting the printing system...
The printing system was reset successfully.
*******************Restarted Computer and re-added printer (test print failed, same problem)*******
###Permission Repairs###
Starting permission verification and repair...
The permissions for the file /Library/Printers/PPDs/Contents/Resources/Lexmark C540.gz are incorrect!
They are -rwxrwxr-x, but should be -rw-rw-r--
Repaired.
The permissions for the file /Library/Printers/PPDs/Contents/Resources/Lexmark C543.gz are incorrect!
They are -rwxrwxr-x, but should be -rw-rw-r--
Repaired.
The permissions for the file /Library/Printers/PPDs/Contents/Resources/Lexmark C544.gz are incorrect!
They are -rwxrwxr-x, but should be -rw-rw-r--
Repaired.
The directory /var/db/lockdown/Library is missing!
The directory /var/db/lockdown/Library/Printers is missing!
The directory /var/db/lockdown/Library/Preferences is missing!
Recreating symbolic links...
Done.
Verification complete.
4880 files examined. 3 permission problems were found and repaired. It is recommended that you verify the permissions again to make sure the values are correct.
3 missing files/directories found during the verification process. They may be responsible for certain printing problems. Print Therapy cannot replace these items. Please refer to the log file for a list of the missing files/directories. You may need to reinstall OS X to resolve your printing issues. Certain files and directories are deleted when using the Reset Printing System option. These files and directories, if required, will be recreated during normal printing.
---Second run (verification run)---
Saturday, July 18, 2009 10:38:13 PM
Starting permission verification and repair...
The directory /var/db/lockdown/Library is missing!
The directory /var/db/lockdown/Library/Printers is missing!
The directory /var/db/lockdown/Library/Preferences is missing!
Recreating symbolic links...
Done.
Verification complete.
4880 files examined. No permission problems were found.
3 missing files/directories found during the verification process. They may be responsible for certain printing problems. Print Therapy cannot replace these items. Please refer to the log file for a list of the missing files/directories. You may need to reinstall OS X to resolve your printing issues. Certain files and directories are deleted when using the Reset Printing System option. These files and directories, if required, will be recreated during normal printing.
*******************Restarted Computer (test print failed, same problem)*******

Database instance shutdown

Hi all,
I got the following message on weekend at this specific time where my database instance was shutdown by itself. I already check it out and there was no other services which is running on the specific time but yet it was shutdown with unknow reason... Anyone of you have this experience before ? The log shown the following message :-
Mon Jun 26 00:57:01 2006
KCF: write/open error block=0x59 online=1
file=2 E:\ORADATA\ORCL\UNDOTBS01.DBF
error=27072 txt: 'OSD-04008: WriteFile() failure, unable to write to file
O/S-Error: (OS 33) The process cannot access the file because another process has locked a portion of the file.'
Mon Jun 26 00:57:01 2006
Errors in file e:\admin\orcl\bdump\orcl_dbw0_3228.trc:
ORA-01242: data file suffered media failure: database in NOARCHIVELOG mode
ORA-01114: IO error writing block to file 2 (block # 89)
ORA-01110: data file 2: 'E:\ORADATA\ORCL\UNDOTBS01.DBF'
ORA-27072: File I/O error
OSD-04008: WriteFile() failure, unable to write to file
O/S-Error: (OS 33) The process cannot access the file because another process has locked a portion of the file.
DBW0: terminating instance due to error 1242
Rgds
Lim

Errors in file e:\admin\orcl\bdump\orcl_dbw0_3228.trc:
generate output file from "tkprof". and check it.
ORA-01242: data file suffered media failure: database in NOARCHIVELOG mode
Cause: The database is in NOARCHIVELOG mode and a database file was detected as inaccessible due to media failure.
Action: Restore accessibility to the file mentioned in the error stack and restart the instance.
it seems to ur undo datafile is not accessible so check u have permission. and if u have bkp of undo file then replace it restart ur database.
or create new undo tbs and replace old one.
hope this help

Replaced N96 restarting

Similar Messages

Maybe you are looking for