Replaced network device with same ip - cannot access ssh/http

Hello-
I replaced a network equalizer and used the same ip. 
<www> - <firewall> -<netequalizer>-<cisco core>-<lan>
I can see this online and we are passing traffic.  Yet cannot access ssh or http. I have been troubleshooting with netequalizer but figure i come here. I am thinking this may be an arp issue on the cisco core? Any thoughts?
thanks

While it might be possible that it is an arp issue on the core I think it is not so likely. Can the core ping the netequalizer? If the core can ping then it almost certainly is not an issue with arp.
My guess is that there was something in the configuration of the previous netequalizer then enables management by SSH and HTTP that was not done in the configuration of the replacement.
HTH
Rick

Similar Messages

  • Server with same Profile cannot access same networking

    Hi,
    I have a lab running 1 x Nexus 5010, 2 x FIC 6120'XP's, UCS 5108 and 2 x B200 M2 Blades. I have configured everything per flexpod guidelines (except I have only 1 Nexus). I boot from SAN over Fibre and zoning everything is working 100% My firmware is 2.1(1f)
    Question:
    Assinged to each blade is 2 vNICs connected to FabricA and FabricB (FabricA = port-channel from FICA to Nexus and FabricB = port-channel from FICB to Nexus - Nexus has 2 different port-channels conf for each link to each FIC)
    After I install VMware, I tag vlan 10 (management vlan) for the management traffic of each VMware node. The funny thing is when I ping server 2, iget a response but not from server 1. Both are configured using the same service profile. If I ping server 1 from server 2, I get a response. This leads me to believe that for some reason the traffic is not leaving the FIC from server 1, but it is when using server 2. I have attached screenshots of both servers vifpaths.
    Can someone please help urgently as this is driving me crazy as I do not know what the hell is going on.
    Cheers                   

    Hello
    Hope this solution will help.
    Just found my notes on deleting the users profile:
    "Deleted Profile logs back in with temporary profile.
    This problem occurs if the current user's profile was accidentally deleted from the system.
    Note: This section, method, or task contains steps that tell you how to modify the registry. However, serious problems might occur if you modify the registry incorrectly. Therefore, make sure that you follow these steps carefully. For added protection, back up the registry before you modify it. Then, you can restore the registry if a problem occurs. For more information about how to back up and restore the registry
    1. Log on to the system by using an administrative user account other than the user account that is experiencing the problem.
    2. Back up all data in the current user's profile folder if the profile folder still exists, and then delete the profile folder. By default, the profile resides in the following location:
    %SystemDrive%\Users\UserName
    3. Click Start, type regedit in the Start Search box, and then press ENTER.
    If you are prompted for an administrator password or for confirmation, type your password, or click Continue.
    4.Locate the following registry subkey:
    HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows NT\CurrentVersion\ProfileList
    5.Under the ProfileList subkey, delete the subkey that is named SID.bak.
    Note SID is a placeholder for the security identifier (SID) of the user account that is experiencing the problem. The SID.bak subkey should contain a ProfileImagePath registry entry that points to the original profile folder of the user account that is experiencing the problem.
    6. Exit Registry Editor.
    7. Log off the system.
    8. Log on to the system again."
    & for more information kindly check the below link too :- http://community.spiceworks.com/topic/187995-network-pc-cannot-access-1-specific-server .
    Regards
    keshav

  • I am using iphone 4..32 gb...i hav updated to ios6..i am experiencing serious lags...watever m doin d phone lags n goes to the home screen...frequency is much greater..please help me with it...i even replaced my device but same problem on new one..!!!!

    please help me with dis...
    I am using iphone 4..32 gb...i hav updated to ios6..i am experiencing serious lags...watever m doin d phone lags n goes to the home screen...frequency is much greater..please help me with it...i even replaced my device but same problem on new one..!!!!

    Restore the phone as a new device. There is probably something that was corrupted on your phone during the update and has been passed via the backup to the replacement phone.  If the corruption/problem is contained in the backup, you'll need to re-sync your data, and re-install your apps manually. Restoring the backup again will only bring the problem back with it.
    If restoring it as new does not fix it, then make an appointment at the genius bar.

  • When i login with microsoft account cannot access with administrative share c$

    i have a problem when i login to windows with microsoft account cannot access any network computer with administrative sharing c$,d$ with windows 8.1 
    but when i login with local account can access
    and some people tell  me create key in regedit t fix it 
    after enter user name and password show this error 
    and i apply your instruction  and not fix until now
    note:
     my Machine windows 8.1 if another machine in network windows 7 can access a hidden share if machine in network windows 8.1 show this message in image 2 
    but if i login with local user can i access all machine hidden share network windows 7 and 8.1

    yes this computer i want to access  name poland2-work and have two users 
    first :administrator
    second : poland 2

  • Mail in Mavericks not replacing existing mail with same name

    Mail in Mavericks not replacing existing mail with same name.
    Thanks

    I have the same situation as you - sending out pdfs of designed pages and wanting to overwrite them continually. It used to happen on an older version of Mail, then it disappeared and now it's back with the latest version.
    It's more than annoying, it's downright driving me nuts. In the last hour I had to quit Mail seven times.
    Please send a fix for this Apple.

  • I have ios7 on my iphfone 4 I now have a iphone5 with ios8 I cannot access the cloud to download my contacts and apps.  the error is both phones need to be ios8,  my iphone4 will not allow changing to ios8.  can anyone help.  Thanks

    i have ios7 on my iphone 4 I now have a iphone5 with ios8 I cannot access the cloud to download my contacts and apps.  the error is both phones need to be ios8,  my iphone4 will not allow changing to ios8.  can anyone help.  Thanks

    Contact Apple and speak to someone in account security.

  • Discovering Network Devices with SNMP not working

    I have implemented SCOM 2012 SP1 CU5 on Server 2008 R2 with SQL 2008 R2 all installed on the same VM running side by side with SCOM 2007 R2 v 6.1.7221.0. I have almost fully decommissioned SCOM 2007 and all that remains on it is 2 network devices that
    I cannot discover with SCOM 2012 using SNMP, no matter what I try. If I just use ICMP the discovery works. I have checked both the devices and SNMP is enabled and if I run this snmpwalk command on both devices I get a response;
    c:\Support\SNMP Walk>SnmpWalk.exe -r:10.X.X.XX -v:1 -c:"public" -os:.1.3.6.1.
    2.1.1 -op:.1.3.6.1.2.1.2
    SnmpWalk v1.01 - Copyright (C) 2009 SnmpSoft Company
    [ More useful network tools on http://www.snmpsoft.com ]
    OID=.1.3.6.1.2.1.1.1.0, Type=OctetString, Value=NetMan 100 plus
    OID=.1.3.6.1.2.1.1.2.0, Type=OID, Value=1.3.6.1.4.1.5491.6
    OID=.1.3.6.1.2.1.1.3.0, Type=TimeTicks, Value=5 days, 1:58:58.04
    OID=.1.3.6.1.2.1.1.4.0, Type=OctetString, Value=SystemsEngineer
    OID=.1.3.6.1.2.1.1.5.0, Type=OctetString, Value=MARMUPS
    OID=.1.3.6.1.2.1.1.6.0, Type=OctetString, Value=FXXXXX
    OID=.1.3.6.1.2.1.1.7.0, Type=Integer, Value=0
    Total: 7
    c:\Support\SNMP Walk>SnmpWalk.exe -r:10.X.X.1 -v:1 -c:"scom05" -os:.1.3.6.1.2.1
    .1 -op:.1.3.6.1.2.1.2
    SnmpWalk v1.01 - Copyright (C) 2009 SnmpSoft Company
    [ More useful network tools on http://www.snmpsoft.com ]
    OID=.1.3.6.1.2.1.1.1.0, Type=OctetString, Value=SSG-140 version 6.3.0r2.0 (SN: 0
    185112006000325, Firewall+VPN)
    OID=.1.3.6.1.2.1.1.2.0, Type=OID, Value=1.3.6.1.4.1.3224.1.52
    OID=.1.3.6.1.2.1.1.3.0, Type=TimeTicks, Value=359 days, 2:20:16.00
    OID=.1.3.6.1.2.1.1.4.0, Type=OctetString, Value=Network
    OID=.1.3.6.1.2.1.1.5.0, Type=OctetString, Value=XXXXXX
    OID=.1.3.6.1.2.1.1.6.0, Type=OctetString, Value=FXXXXX
    OID=.1.3.6.1.2.1.1.7.0, Type=Integer, Value=72
    Total: 7
    The first device is a Marms UPS which has had its firmware upgraded, which was discovered using SNMP in SCOM 2007 and the second device is a Juniper SSG-140 Firewall, again this is discovered using SNMP in SCOM 2007.
    I believe that I have setup SNMP correctly on SCOM 2012 because I have 28 other networks devices discovered using SNMP using an explicit discovery, some of these being newer Marms UPS's, emerson air conditioners, netapp SAN etc.
    I have added any and all accepted community names in the SNMP service properties on SCOM 2012 and enabled accept SNMP packets from any host.
    Does anyone have any information that they could forward to me or point in the right direction to troubleshoot this issue for eg run some snmp get commands and capture / filter traffic with wireshark, what do I look for? Any other logs to check besides the
    obvious ones? Any known issues with SCOM 2012 SP1 and SNMP, should I upgrade to R2? It just seems that some network devices get discovered with ease and others do not and I am running out of ideas. Thank you all in advance.

    Patrick, thank you for your reply.
    Yes the snmpwalk command is run from the new SCOM 2012 server which has the discovery rule on it.
    I don't have any pending network devices, its blank.
    Could there be an issue with my discovery rule? I have noticed that each time I make a change to, for eg, the access mode and change this from ICMP to ICMP/SNMP, save it, run it, it doesn't seem to update the said network devices access mode's in network
    devices, it just stays on ICMP. Do I have to manually remove the network devices which have been discovered before making any changes to the discovery rule and running it which I have done? They don't seem to appear in network devices pending management either?

  • MacBook shows only folder with ?. Replaced hard drive with same results.

    In the midst of some work the machine simply clicked and showed a folder with a ?. Would not restart. Replaced the drive with a new 7200 Seagate momemtum, 320GB, installed the software, and have the same problem with startup. A folder with a ? Connect another machine via firewire and looked at the MacBook drive and it showed the appropriate system folders. Then started the other computer from the MacBooks hard drive and that worked. So the drive appears healthy but we cannot get it started on its own. In Disk Utility the new drive is indicated as not owner enabled, whatever that means. It appears most Macs that work are, in fact, owner enabled. Anybody have a clue what might be going on here? We're thinking maybe the first drive had not failed and the problem lies elsewhere.

    As an FYI, here is the apparent solution. The original drive did fail. Because the disks were in Seattle and we were attempting to fix it in Dallas we connected via Firewire to a PowerPC machine and formatted the drive. That was the crucial error. the G4 did not give the appropriate Intel-based Mac formatting options. So we could look at the drive from the G4 and see everything was there, but the MacBook could not boot itself because it could not read the disk which was improperly formatted. The Genius bar in Seattle figured this out and reformatted the disk at no cost.
    All's well that ends well, but have Macs really become that complicated?

  • I have macbook pro w existing iPhoto library. Now have Canon printer and loaded Canon software for same. Cannot access iPhoto library from Canon software, but prints fine from iPhoto. How can I use iPhoto library w Canon software?

    I have a macbook pro w exisitng iPhoto library. I now have Canon printer and loaded Canon software for same. I cannot access iPhoto library for use from Canon software. I can print from iPhoto directly to new printer without problem. How can I use iPhoto library with Canon software? I would like to try the software to see which I prefer...

    Simply export some photos from iPhoto to a folder on the desktop and experiment.
    Without telling us even what this program is, not to mind what it does, that's the best anyone can suggest.
    Regards
    TD

  • Set up family on several devices with same apple id

    I have successfully started Family from my iphone and got my kids and wife connected. But when trying to add my ipad with same id as I use on my iphone I cannot succeed. It states that an account can only be connected to one family at a time. How is the procedure for this?

    I could have solved it by inviting myself.

  • I have a strane error message when syncing with itunes + i cannot access it

    Hi all,
    this is only place i thought of that might know these problems:
    1. I cannot access itunes store from itunes - it just says loading... and doesn't load anything
    2. I have an error:
    " ITunes cannot sync photos to the iPhone because the folder "My Pictures" cannot be found.
    I tried installing iTunes again and didn not help.
    Please help,
    Thanks in advance,
    Eran

    In the course of your troubleshooting to date, have you worked through the following document?
    iTunes: Troubleshooting issues with third-party iTunes plug-ins

  • I have a replacement 9.7 Pendo pad, I cannot access the Adobe site

    I have a 9.7 Pendopad which has been given to me as a replacement for one where the battry failed. I was able to access the Adobe web site to get access Overdrive Media, I cannot even get access to the Adobe Site to even sign in , I cannot access any par of the site not even support,
    so I am doing this on my Laptop. the pad is anAndroid version 4.2.2 . I can access all the other Web sites but not  Adobe .
    Please has anyone any ideas how to gain access using my Tablet.
    Rgards Tony Cole

    I don't know why this is happening to you; maybe your Wi-Fi connection is unstable?
    I just tried from my Android tablet to login to http://www.adobe.com/, https://www.acrobat.com/, https://www.facebook.com/ - no problem whatsoever.
    I also opened Adobe Reader, and I get autoatically connected to Acrobat.com

  • EA6500 has numerous "network devices" with no MAC

    I have noticed from time to time I get many (15-20) "network devices" in the Device List with no MAC address. I notice this mainly when managing Parental Controls. I go and clean up the Device List and days later they reappear.
    Another interesting thing is that the computer I am writing this with (through the router) does not show up in the Device List and I have an IP address from the router.
    I have the latest firmware 1.1.28.146856.
    Does anyone else see this on their EA6500?

    There are a lot of people who reported similar or related cases that you have right now. From what I have read, they reset their routers back to factory settings. There is one who got to a work around by adding all of his devices to the DHCP Reservation List and the router is working fine after that.

  • Trouble using facetime on another device with same apple id

    Hi
    I am having trouble using facetime with my wife.  I have an iPad 2 and she has an IPhone 4S.  When we try to facetime, we are able to connect for a few seconds and then it drops off.  We are then unable to reconnect.  We both have the same apple Id and e-mail address although I am trying to contact her via her mobile number.  Any suggestions would be grateful received.

    Get an email address (free gmail.com) to use on the iPad.
    Using FaceTime http://support.apple.com/kb/ht4319
    Troubleshooting FaceTime http://support.apple.com/kb/TS3367
    The Complete Guide to FaceTime + iMessage: Setup, Use, and Troubleshooting
    http://tinyurl.com/a7odey8
    Troubleshooting FaceTime and iMessage activation
    http://support.apple.com/kb/TS4268
    iOS: FaceTime is 'Unable to verify email because it is in use'
    http://support.apple.com/kb/TS3510
    Using FaceTime and iMessage behind a firewall
    http://support.apple.com/kb/HT4245
    iOS: About Messages
    http://support.apple.com/kb/HT3529
    Set up iMessage
    http://www.apple.com/ca/ios/messages/
    iOS 6 and OS X Mountain Lion: Link your phone number and Apple ID for use with FaceTime and iMessage
    http://support.apple.com/kb/HT5538
    How to Set Up & Use iMessage on iPhone, iPad, & iPod touch with iOS
    http://osxdaily.com/2011/10/18/set-up-imessage-on-iphone-ipad-ipod-touch-with-io s-5/
    Troubleshooting Messages
    http://support.apple.com/kb/TS2755
    Troubleshooting iMessage Issues: Some Useful Tips You Should Try
    http://www.igeeksblog.com/troubleshooting-imessage-issues/
    Setting Up Multiple iOS Devices for iMessage and Facetime
    http://macmost.com/setting-up-multiple-ios-devices-for-messages-and-facetime.htm l
    FaceTime and iMessage not accepting Apple ID password
    http://www.ilounge.com/index.php/articles/comments/facetime-and-imessage-not-acc epting-apple-id-password/
    FaceTime, Game Center, Messages: Troubleshooting sign in issues
    http://support.apple.com/kb/TS3970
    Unable to use FaceTime and iMessage with my apple ID
    https://discussions.apple.com/thread/4649373?tstart=90
    How to Block Someone on FaceTime
    http://www.ehow.com/how_10033185_block-someone-facetime.html
    My Facetime Doesn't Ring
    https://discussions.apple.com/message/19087457
    To send messages to non-Apple devices, check out the TextFree app https://itunes.apple.com/us/app/text-free-textfree-sms-real/id399355755?mt=8
    How to Send SMS from iPad
    http://www.iskysoft.com/apple-ipad/send-sms-from-ipad.html
    You can check the status of the FaceTime/iMessage servers at this link.
    http://www.apple.com/support/systemstatus/
     Cheers, Tom

  • Please help with Error #1009 Cannot access a property

    Hi All,
    I have a simple flash movie where play_btn should go to a label on a timeline where I have a video playing and a stop_btn should go back to a first frame (label "start") and thus give an illustion of stopping the movie.
    I have no problem with the play_btn, however stop_btn doesn't work and when I test the movie I get the following error message:
    TypeError: Error #1009: Cannot access a property or method of a null object reference.
        at FSV_header1_fla::MainTimeline/frame1()
    below is my code - any help is very appreciated!
    stop();
    play_btn.addEventListener(MouseEvent.MOUSE_DOWN, playMovie);
    close_btn.addEventListener(MouseEvent.MOUSE_DOWN, stopMovie);
    function playMovie(event:MouseEvent):void {
        trace("Play!");
        gotoAndPlay("start");
    function stopMovie(event:MouseEvent):void {
        trace("Close!");
        gotoAndStop("stop");
    Thank you!!

    Thank you!!
    I was able to fix it by putting all the buttons on the first frame and toggling visibility on/off. Here's the code:
    stop();
    close_btn.visible = false;
    play_btn.addEventListener(MouseEvent.MOUSE_DOWN, playMovie);
    close_btn.addEventListener(MouseEvent.MOUSE_DOWN, stopMovie);
    function playMovie(event:MouseEvent):void {
        trace("Play!");
        gotoAndPlay("start");
        play_btn.visible = false;
        close_btn.visible = true;
    function stopMovie(event:MouseEvent):void {
        trace("Stop!");
        gotoAndPlay("stop");
        close_btn.visible = false;
        play_btn.visible = true;

Maybe you are looking for