Replacement 6100G will not complete configuration

Received a new Westell 6100G modem for one determined by Verizon to have failed. After clicking on the Verizon set up page I selected the "this is a replacement modem" and followed instructions. The screen then showed that it was processing and advised a likely three minute wait. After about 6 minutes a screen appeared stating that configuration could not be completed. Have been without internet for about a week. Have spent many hours with tech support in India. One tech determined that first modem had failed only after using for 10 days. Don't know what to do now. Need to have a repair tech visit to check the line and possibly install a cat 5 from network interface to jack..

Do the following to fix this. I don't know why they need to run an Activation Wizard these days with OpenPPPoE being so abundant!
Visit http://192.168.1.1/ and log in using the Default Username and Password of admin/password respectively if prompted.
Change the default password on the modem to something you will remember
Visit the following link: http://192.168.1.1/verizon/redirect.htm OR http://192.168.1.1/verizon/redirect (This one is if you have an ActionTec)
Click Disable on the page.
BOOM Internet's back. Done in 2 minutes, no software but a Web Browser needed.
========
The first to bring me 1Gbps Fiber for $30/m wins!

Similar Messages

Recovery will not complete. Gets stuck on Configuring screen

L505D-ES5025 Lap top. The speakers and USB ports were not working. After trying to download drivers with no success, I decide to recover the system to factory default software. It will not complete. I left it from 4:30pm yesterday to this morning and It is still stuck on that screen. I forced a shutdown and opened windows safe mode with command prom and ran CHKDSK, and it said there were no problems with the disk. Can someone help me?

I have had this problem L505D-LS5007for many months and have sent the laptop to Toshiba Repair 3 times under warranty and it kept coming back as hardware failure and that they replaced the system board. Once the hard drive was replaced as well as the system board. The last time I sent it in, it kept running for several months. I believe that the problem starts when Microsoft does an update. I am guessing that the hardware is NOT supported by Microsoft Windows 7 out of the box software and Toshiba has used their special drivers software to configure some of the non standard Windows 7 hardware for this particular laptop version. Probably to slip Windows 7 into a machine that they had in stock and needed to sell. When a Microsoft update comes along, the hardware is reconfigured improperly for the L505D-LS5007 hardware configuration. I also think that this may cause a hardware failure as the configuration is wrong and causing something to overheat. As I try to restore, the high speed fan is always on and the exhause sire from the fan is hot. I am at a loss too how to fix this problem. Same problem, no USB, no speakers cannot complete restore. Hardware? Probably due to a software problem that caused the failure. I wonder if XP 64 bit would work? Anyone try that? Of course if the hardware has failed, another OS will not help. Too bad we just happened to buy a good laptop that was not meant for Windows 7 platform.

I am trying to install the latest update for HP Printers, it will not completely install ,now my printers won't work. Help!

I am trying to install the latest update for HP Printers, it will not completely install ,now my printers won't work. Help!

Hello Carolyn - Thank you for your quick response to my concerns, I had already gone to the HP support site and tried to get the latest HP drivers, the site said for Lion 10.7 there was NA version. So, I just used my time machine to replaced the OS from that time spot. I got my printers working again, so all right with the printer. But, the fact remains that I still keep getting the New Update HP Printer in the software update window. But, what happens if I try to download and install it is this: It starts the download, everything seems to come down fine, it starts write the files and then starts moving items into place, the blue bar fills to all most the end and slows down to a stop and never completes the installation. I have left my laptop on over night and it never finishes the operation. I can only force quit the software update. Which has knock out my printer drivers. Now, I just keep unchecking the box in the software updates for new HP printer software. Is anyone else having this problem or is it just my system? Sincerely: Professor G

3rd gen iPod will not complete the RESTORE process with new Hard Drive

I have an 3rd gen iPod and I have replaced the hard drive with a newer MK2006GAL. The drive formats fine with a USB cable, formating Mac OS Extended Journaled. It will not complete a "restore" when connected via FireWire in iTunes or with any ipod updater utility. this happens on any mac (we have several). It will not even see the iPod updater when connected via USB and it says MUST CONNECT WITH A FIREWIRE CABLE. It will not format with Disk Utility when connected with the Apple FireWire cable only USB. This is the second new hard drive I have tried. I thought the first "replacement drive" was bad. Turns out it must be something else. Does this sound like a bad battery or motherboard or bad FireWire cable to you? The connectors look fine (under magnification). other problems, while this iPod will not Restore properly, it also will not turn off.
Would like to know if anyone else has seen this trouble.
thanks.
Powermac G4 1.25 MDD, OS9/OSX, 3rd gen iPod Mac OS X (10.3.9)
Powermac G4 1.25 MDD, OS9/OSX, 3rd gen iPod Mac OS X (10.3.9)
Powermac G4 1.25 MDD, OS9/OSX, 3rd gen iPod Mac OS X (10.3.9)

Hmm now getting this message.
"The ipod "ipod" could not be restored.An Unknown Error occured (1429)".
It still will not format. Does anyone know what a 1429 error is?
Powermac G4 1.25 MDD, OS9/OSX Mac OS X (10.3.9)

My ipod touch is not list as a device on itunes. When I tried do update itunes, I get a ox8007054f error code and the update will not complete.

My ipod touch is not listed as a device when connected to my computer. As suggested I attempted to download the latest of itunes. I got an
ox8007054f error code and the down load will not complete. I have also tried to restore my computer to an earlier setting, but it will
not accept the change.

Have you looked at this completed previos discussion. It discusses 0x8007054F.
Re: Error message when trying to install iTunes

Pages '08 will not complete save function. I must force quit to save.

Pages '08 will not complete save function. I must force quit to save.

When saving, try "Save As" but make sure "Include preview in document" is NOT selected.

HT1657 I have rented two movies on my laptop and they will not completely download..it shows that they are theere but when i try to watch them on my laptop or my ipad it wont open up???? help

I have rented two movies on my laptop and they will not completely download..it shows that they are theere but when i try to watch them on my laptop or my ipad it wont open up???? help

Welcome to the Apple community.
A number of people have reported similar issues recently, many appear to have found a discrepancy of some kind in their account settings and making changes to these settings or simply resetting them has resolved the matter.
Check your account details are correct, check that you are using the correct details for Location, Region and Time Zone. You may want to change these settings and then change them back to see if that helps.
You might also try logging out of and then back into your iTunes account (Settings > iTunes Store > Apple ID’s > Sign Out) and restarting your router. (Some have reported that after doing this, they need to check for rentals even though it may report that there aren’t any, after which rentals once again appear in the ‘movies’ feature)
Rentals should appear under their own heading in the ‘Movies’ feature, you might also check at Settings > iTunes Store > Check For Rentals.

My iPod 5th gen will not completely turn on it shows the apple symbol then shuts off I have restarted it and tried to plug it into my computer but cannot find it to restart it

My iPod 5th gen will not completely turn on it shows the apple symbol then shuts off I have restarted it and tried to plug it into my computer but cannot find it to restart it
Its been like this for awhile and I can not fix it

Try:
- iOS: Not responding or does not turn on
- Also try DFU mode after try recovery mode
How to put iPod touch / iPhone into DFU mode « Karthik's scribblings
- If not successful and you can't fully turn the iOS device fully off, let the battery fully drain. After charging for an least an hour try the above again.
- Try another cable
- Try on another computer
- If still not successful that usually indicates a hardware problem and an appointment at the Genius Bar of an Apple store is in order.
Apple Retail Store - Genius Bar

HT3669 My Epson Perfection 1200 scanner functions as a flatbed scanner but when I try to scan transparencies the control panels change in Image Capture but the scanner bar will not complete the overview scan & cannot travel beyond the first 2/3 centimet

Epson Perfection 1200 scanner continues to function as a flatbed scanner but when I try to scan transparencies/film negs the control panels change in Image Capture but the scanner bar will not complete the overview scan & cannot travel beyond the first 2/3 centimeters. All the communications seem to recognise the scanner and the mode for the intended scan but the necessary overview scan is not completed, nothing comes up on the Image Capture scan window. If I unplug the film adaptor I can get a document scan. When I plug in the adaptor again the Image Capture details change which allows me to select the type of scan required but when the scanner attempts an overview scan it is unable to complete it.
I have had the scanner from new (12 Years) and have previously scanned slides and film with the adaptor but maybe this was before I upgraded my computer (imac 27").
Do I have to buy a new scanner? It seems so close to working correctly.
I have downloaded the Epson recommended driver (5.4) and have Epson Perfection 1200 6.6 Universal showing in the Applications List.
Any thoughts or observations would be much appreciated before I go out and spend money an new hardware.
Thanks

I have same issue - have you solved this yet?

My iTunes library will not completely sync to neither my iPad nor my iPhone -- both are completely updated with the latest software. What do I have to do?? When I try to do the "autofill" option when connected to iTunes it says "no songs can be copied"

My iTunes library will not completely sync to neither my iPad nor my iPhone -- both are completely updated with the latest software. What do I have to do?? When I try to do the "autofill" option when connected to iTunes it says "no songs can be copied"...I literally bought some of these songs yesterday on my iPhone and now I can't sync them to my iPad. What is this issue? Usually I would just have to plug either device into iTunes and everything would sync, now nothing new syncs.

On your iPad tap Settings > Store
Switch Books off then back on then reset your iPad.
Hold the On/Off Sleep/Wake button and the Home button down at the same time for at least ten seconds, until the Apple logo appears.

An app will not completely download from the App Store to my iPhone 5S. Neither can I terminate the download by trying to delete it. The app is useless to me and so I would like to remove the icon from my home screen. How can I do this?

I tried to download the app "Google Translate" from the App Store onto my iPhone 5s. However, the download will not complete. As well, when I try to delete the icon from my home screen, it will not go away. I am very frustrated as this has never happened before and I have gotten many paid and free apps from the App Store. I hope someone can solve my dilemma. Thank you kindly.

What have you tried to get the app to finish downloading e.g. have you tried logging out and back into your account on your phone, disconnecting and reconnecting to your network, soft-reset of your phone (press and hold both the sleep and home buttons for about 10 to 15 seconds, ignore the red slider, after which the Apple logo should appear and it should reboot) ?
You could also try downloading the update on your computer's iTunes and see if you can sync it over to your phone (or delete the app its Apps tab when connected to your computer's iTunes and sync the new version - deleting the app will delete its contents).

My MacBookPro (mid 2012) will not complete the boot process. Yosemite's progress widget gets about 1/3 to 1/2 way across when the logo disappears and the screen goes all white for 10-15 secs or so, then the machine shuts down and restarts.

My MacBookPro (mid 2012) will not complete the boot process. Yosemite's progress widget gets about 1/3 to 1/2 way across when the logo disappears and the screen goes all white for 10-15 secs, then the machine shuts down and restarts. This sequence will repeat seemingly forever unless I shut it down manually.
I upgraded to Yosemite from Mountain Lion a couple months ago, skipping Maverick completely, and I've done any associated updates that Apple told me about. I don't recall which version of Yosemite I have, but I'm sure it is the "latest and greatest".
I've tried re-starting in Safe Mode / Safe Boot and that does the same thing as described above except without the endless restarts. Instead of restarting at some point, SafeBoot proceeds to the white screen and then it hangs until I restart it manually. (I've waited as long os 20-30 minutes with no response).
When I tried the option-command-p-r key combo I never get any chimes or other noises besides the original 1 time boot sound that you would expect to get when starting up a macbook pro.
I was using the mac quite normally (meaning I was doing work I normally do on it and there was no indication of anything wrong) immediately prior to this happening.
The machine is BootCamp(ed) with Windows 8.1 which I use from a VMWare virtual machine instead of natively so that I can have both OSes running at the same time. I also think this is unrelated to my problem. I have been using this setup for more than 2 years.
My upgrade to Yosemite was uneventful and I thought it went well and was very smooth. I don't want to lead attention away from Yosemite, but at this point my problem does not seem related to the upgrade.
Any help is appreciated.

Install or Reinstall OS X from Scratch
Be sure you backup your files to an external drive or second internal drive because the following procedure will remove everything from the hard drive.
Boot to the Recovery HD:
Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
Erase the hard drive:
1. Select Disk Utility from the main menu and click on the Continue button.
2. After DU loads select your startup volume (usually Macintosh HD) from the
      left side list. Click on the Erase tab in the DU main window.
3. Set the format type to Mac OS Extended (Journaled.) Optionally, click on
      the Security button and set the Zero Data option to one-pass. Click on
      the Erase button and wait until the process has completed.
4. Quit DU and return to the main menu.
Reinstall OS X: Select Reinstall OS X and click on the Install button.
Note: You will need an active Internet connection. I suggest using Ethernet if possible
           because it is three times faster than wireless.

My iPhone 4 will not complete a back up. Error - 5000 comes up

Error 5000 appears after "preaparing phone for back up" completes. "Continuing will result in the loss of all contents of this phone" is the message. Phone will not complete a synch and iTunes often goes into "Not responding". I have repaired iTunes by downloading the software from Apple's website. No improvement.
Can anybody offer a solution?

This is a bad situation. Your iPhone is in a state which cannot be backed up, and the Restore will return iPhone to factory specs erasing it. You need to Restore your iPhone to get it working again. If you were experiencing problems before, maybe your iPhone is damaged. If still faulty, and you have Warranty or AppleCare take iPhone to Apple for evaluation. If no coverage and still faulty it may be time for new phone.

Mavericks 10.9.1 keeps erring during the download and will not complete. What do I do?

Mavircks 10.9.1 keeps erring during the download and will not complete. What do I do?

Get the official version of Firefox here: http://www.mozilla.com/en-US/firefox/
As long as you '''''don't''''' select the option to '''Remove Firefox personal data and customizations''' when you un-install that "Yahoo version", you won't lose anything.

Lightroom 5 will not complete download on Mac OS X 10.6.8

I have purchaces Creative Cloud package 5 of the segments have downloaded ok but Lightroom 5 Gaming SDK 1.3 and Scout CC will not complete download any advice.

Lightroom 5 will not run on Mac OS X 10.6.8
http://www.adobe.com/products/photoshop-lightroom/tech-specs.html
Lightroom 5 requires OS X 10.7 or higher.

Replacement 6100G will not complete configuration

Similar Messages

Maybe you are looking for