Replacement Chipset/Heatsink Fan (northbridge? for k7n2 delta-ilsr)

   < i need a replacement heatsink and fan for this fan.  that will fit!          Reason: I want a new one that is quiter, and the original fan in it broke.  I also need to be able to buy these part(s) online.

Me too. You can get them in copper or aluminium. I have the latter, and for more than year now it's been doing a fine job with minimum noise.
Check it out here:
http://www.pcabusers.com/reviews/iceberg/p1.html

Similar Messages

  • AGP Setup For k7n2 delta ilsr

    I have a k7n2 delta ilsr mb, in display properties on desk top setting tab then advanced button then GeForce tab under adapter information is Bus and memory. To the right of Bus it reads AGP (PCI mode) shouldn't that read AGP (8X), how can I change this. Ron.

    Hi,
    No, leave it at 64 or 128.
    Go here for an explanation:
    http://www.rojakpot.com/default.aspx?location=7&var1=18
    Then - Click on:  "Free Access To the BIOS Optimization Guide" near the bottom of the page - then click on "AGP Aperture Size"
    Axel  

  • Need help with jumper settings for k7n2 delta ilsr

    I have a k7n2 delta ilsr and I'm using a AMD 2800+ barton 333 fsb. I'm not sure what the jumper settins are for this cpu. The users guide only shows 133/166 and 200, can anyone help me with the jumper settings.
    Thanks, Ron.

    Hi,
    As your processor is 333FSB - the jumper should be set to 166FSB as should the BIOS. As your RAM CPU combination runs at 2x166=333 or thereabouts.
    Basically, as a general rule, if you halve the FSB speed of your processor you'll get the setting for both BIOS and Jumper. 200FSB=100, 266FSB=133, 333FSB=166 etc. etc.
    Axel  

  • Kingston HyperX Memory for K7N2 Delta-ILSR

    Hey will my K7N2 Delta-ILSR support the Kingston HyperX serises DDR400-512MB Ram?
    Im looking to buy 2 maybe 3 of these and really want to be sure theyll work.
    http://www.ec.kingston.com/shop/partsinfo.asp?ktcpartno=KHX3200A/256&promo=hx2shp
    I checked the supported ram list for the K7N2 Delta-ILSR  and they wernt on there so i just figured it may be out of date?
    So thanx in Advance for info!
    p.s. It will support 3x 512MB right?

    Has anyone noticed how the Hyper X went from the poor-man's Corsair to being priced equal to OCZ, and usually higher then Geil, as well as usually being very close to Corsair, if not the same? I think only Mushkin beats it out now price-wise...

  • New Modded BIOS for K7N2 Delta ILSR

    MSI K7N2 Delta ILSR Modded BIOS based on Official v. 7.80 BIOS
    download here:

     Description: Access through interface which is on insecure interfaces list detected. Request aborted.
    Interface/Client IP address:
     Date: Wed, 18 May 2005 13:11:17 GMT
    Doesn't work for me 
    By the way did u put the bios to vork with 1.3 vcore like the braziliantech one that does't exist anymore ?
    EDIT: Thanks it's working now 

  • Case Recommendation for K7N2 Delta-ILSR

    Greetings,
    I'm looking for a mid size ATX case that that has the front usb etc. ports prewired as to work easily with a K7N2 Delta-ILSR mb.  By that I mean I don't have to plug each wire individually (with names that don't match) just a plug that goes on the mb.  My eyesight isn't as sharp so hooking up those one wire at a time is tediuous.  Not to mention the lack of starndards   Does anyone know if this is address on the next rev of mb's (with pcix etc).
    Thanks

    Brazos,
    I have yet to see a case that has all the USB wires together, they are all 1 pin at a time. You will find the Antec line of cases very good. (You can always use a magnifying glass to see the pins.) The pin names on the Antec cases are standardized and easy to figure out.
    If you want a good case at a cheap price, then go with the SLK3700AMB:
    If you want a good high end case, then go with the Sonata:
    If weight is an issue, then go with the Super Lanboy:
    Take Care,
    Richard

  • Warranty Length for K7N2 Delta-ILSR

    What is the mfg's warranty length on the K7N2 Delta-ILSR?
    I filled out the online support form earlier today but no response as of yet, and me being the impatient rascal I am, I didn't want to wonder all weekend. I bought it October, 2003 and the floppy drive controller seems to have gone out.
    Thanks!
    HH

    Thank you, Glenn!
    Looks like mine is 2 yrs. & 4 months old. Kind of stinks that I lost 5 months on the warranty by going by the mfg. date instead of date of purchase. Its not worth the hassle & would even cost more to RMA it for the controller. Ahh, but this is IT, the "World of Workarounds". I'll live!
    Thanks for your time, Glenn! 
    HH

  • Temperature reading for K7N2 Delta ILSR

    I have a 2500+ Barton (333 FSB) to work with K7N2 Delta ILSR and 2x256 MB Samsung DDRAM(400 FSB).I use MBM to read my CPU temperatures.Usually 45-47 C idle and 54-58 C under full load.I overclock CPU to 400 FSB and I get LOWER TEMPERATURES!!!!!
     I use 1:1 bios setting for CPU and DRAM speeds either 333 or 400 FSB.
     How can this by possible?

    I use Speedfan which seems to follow the temp in the bios. I've heard that MBM is also accurate. As far as your temps going down on a OC that is very odd indeed.  

  • Anyone help - need I/O plate for K7N2 Delta ILSR??

    I'm based in the UK but will pay P&P worldwide........
    cheers
    D.

    Good luck!
    http://search.stores.ebay.com/ws/search/StoreItemSearch?catref=C5&fcl=3&from=R7&frpp=50&fsoo=1&fsop=1&sacat=-1&satitle=k7n2+delta+ilsr&sbrexp=WD1S&sif=1&sofindtype=0&sofp=4&ssPageName=WD1S
    Edit: If applicable:
    http://www.mycableshop.com/sku/ATXBACKPLATE.htm

  • Linux for K7N2 Delta-ILSR

    Hello,
    Does anyone know of with Linux distro is compatible with the K7N2 Delta Series?
    Sincerely, Deft

    Knoppix worked too, even my TvTuner worked.
    Not that I would recommend Knoppix as a solution, I was just playing.
    There is a lot more support for the nvidia kit now.

  • Best agp card for k7n2 delta ilsr

    Hi again folks
    I'm thinking of upgrading my graphics card as although this card has never let me down its the oldest component in my box, I would like to get something in the sub £100 range, I dont do games but may wish to in future, mainly it would be for photo apps/running-backup-watching dvd's etc. any info would be greatly appreciated tia Hazzo

    I notice your talking in £'s so I assume your located in the UK. 
    Have a look around overclockers.co.uk
    For a sub £100 I noticed a good offer:
    HIS ATI Radeon 9800 Pro - £82
    Also, the 6600GT here is only £103.24 (£106 inc delivery), altough only 4 left in stock so buy now if you want one 

  • MSI K7N2 Delta-ILSR Noisy Northbridge fan

    Hi
    I'm having a problem with the nforce chipset fan on my K7N2 Delta-ILSR.
    It makes a horrible wailing sound when cold booting and is only running at about 2500rpm instead of 4000rpm.
    It does this usually for about 30 seconds then runs normally.
    Does it just need cleaning   or is it on it's way out?
    Any help would be greatly appreciated.
    Thanks
    Garfy

    Quote
    Originally posted by Garfield
    Hi
    I'm having a problem with the nforce chipset fan on my K7N2 Delta-ILSR.
    It makes a horrible wailing sound when cold booting and is only running at about 2500rpm instead of 4000rpm.
    It does this usually for about 30 seconds then runs normally.
    Does it just need cleaning   or is it on it's way out?
    Any help would be greatly appreciated.
    Thanks
    Garfy
    Hi,
      I had the same problem. All I did was loosened the left screw(when looking from the front of the case) until the noise stopped. Give it a try!!!

  • MSI K7N2 Delta ILSR - Noisy Grinding Motherboard Fan

    Hi,
    The Motherboard Fan on my MSI K7N2 Delta ILSR has started to make a terrible grinding noise and I was hoping someone could offer some help on how to replace it.
    Some of the questions I have are -
     + Is the Motherboard Fan screwed on or glued on?
     + Could I replace it with a suitable heatsink (no fan)?*
     + If it is glued on, what is the best way to remove it?
     + If it is glued on, could I just unplug it and stick a new fan on top of the existing one?
     + Has anyone else had this problem and if so what did you do to fix it?
    * I was looking at a Zalman Motherboard Heatsink from http://www.quietpc.com/uk/vgamb.php
    Thanks in advance, Jason.

    Quote
    Originally posted by cgrossi
    add some thin oil on its axis. oil for sewing machines.
    It's not a good idea to add oil to any parts in a computer.  

  • K7N2 Delta ILSR Chipset removal?

    Hi I have been tryin to replace the k7n2 chipset heatsink/fan for a Iceberq as the current fan has died. I unlock the clips from the back of the board but it cant seem to come off as it seems to be stuck the the board. Is there any way of gettin it off without bringing the chip off with it?

    Quote from: Fredrik Åsenius on 10-March-06, 06:46:53
    I don't think arifm2k had a problem with glue. These little pieces of plastics on the back-side of the mobo, for the chip heat sinks, are miniature sized. They are self-locking and must be contracted(?). You need just the right tool - a pincer(?) perhaps - at the same time as you need to use considerable force to push them out.
    In fact, when I'm at it , I fear it is more risk to the work than using a screwdriver to loosen and fasten the processor heat sink.
    I know that after his last post...your last post before mentioned glue...that is why I just threw that out there
    IF I can't do it with my fingernails, I'll carefully use a pair or small needle nose pliers I dipped in PlastiDip for that purpose only.

  • Dont find any connection for PFC on K7N2 Delta ILSR

    Hi !
    Just bought a MSI Motherboard K7N2 Delta ILSR
    Looking for the connector pin for my PFC  ( Power fan Control)
    I can only find two fanconnectors on the board
    CPU and System
    SORRY if this question has been asked before
    searched the Forum but did not find anything

    I just installed this same board. I only found 2 also, so I suppose that is all there is.  If you are trying to set the system up so you can monitor the power supply temps and fan, here is what I did.
    The chipset fan is a 12V fan, so unplug it from the motherboard and power it by using an adapter so you can run it off one of the Molex leads.  I do not know if they make these because I fabricated the wiring myself.  You will not be able to monitor the chipset temps though.
    To fab the connector, I just used the wiring from an old system fan and soldered two small pins (about  one-quarter of an inch long), covered each lead with heat shrink and plugged them in via a standard Molex connector.  Make sure that you do not leave any of the pin exposed, ie: (the heat shrink should push up to the plastic of the chipset fan connector)..  I finished it by covering the new connector with heat shrink to make sure it didnot come apart.
    Now you can use the northbridge fan control for the pfc.  This has worked good for me, and was $30 cheaper than a fan controller unit

Maybe you are looking for

  • Cannot figure out why "ORA-01000 Maximum open cursors" is shown...

    Hello there ... I am programming a PL/SQL Code that is throwing 0RA-01000 Maximum Open Cursors Exceeded. Having already read quite a lot about ORA-01000 errors, I know I should be closing cursors, and have already tried setting OPEN_CURSORS parameter

  • Camera Raw 6.7 update failed

    I tried to update my camera raw to 6.7 for my CS5, but halfway through it keep telling me to close adobe bridge. Its not open. I even tried opening it and closing it and still I get the same message ever time I hit the continue button in the update w

  • Select schema via cursor

    I am working with a database in which all schemas have the same tables. I am trying to write a PL/SQL routine that will loop through each schema, query a table in that schema, and insert that data into a master table (simplified explanation). I can g

  • RRI : Web Template (7.0) as a receiver Query

    Hi All, I am facing a strange problem. In sender query, I have Employee,Employee Post and Employee Start Date. I have to pass employee to Receiver Web Template which shows Employee History. When the employee number is passed to the receiver, it ask t

  • How to protect protected classes?

    I�m Brazilian, and I am learning English language yet. I�ll try to describe my problem. I am using protected and friendly classes, but it doesn�t avoid anyone to use them, because if someone knows the package name of my protected class, this person c