Replacement for Cat 6500

Hi all
Is there a replacement for Cat 6500
Thanks

Hi ,
You can use DFC4XL . XL means , it has more memory and store more TCAM table .
What is the difference between DFC4 and DFC4XL?
A. DFC4XL offers more scalability in terms of IPv4/IPv6 FIB entries, ACL entries, and NetFlow entries compared with DFC4 (see Table 3). Other than those hardware scalability differences, there are no feature differences between DFC4 and DFC4XL.
Table 3. Feature Differences Between DFC4 and DFC4XL
Feature
DFC4
DFC4XL
IPv4 unicast/MPLS forwarding entries
256K
1024K
IPv6 unicast/IPV4 multicast forwarding entries
128K
512K
NetFlow entries
512K
1024K
ACL and QoS TCAM size
64K
256K
1K = 1024.
http://www.cisco.com/c/en/us/products/collateral/switches/catalyst-6500-series-switches/qa_c67-362061.html
HTH
Regards,
VS.Suresh.
*Plz rate the usefull posts *

Similar Messages

Migrate/Replace Cat 6500 Supervisor

Any guides or tips on how to replace a Cat 6500 Sup 32 8G with Sup 720 10G? This is a single 6509 with 2 sup engines.
thanks

Because your supervisors are different you will need to remove both supervisors and replace them at the same time. You won't be able to run a SUP32 and a SUP720 at the same time.

Password Recovery for Catalyst 6500

Hi all,
According to this website:
http://www.cisco.com/en/US/products/hw/switches/ps708/products_password_reco
very09186a00801349aa.shtml
Password will not be activated in the first 30 second, so when we want to do
the password recovery, we just press enter and quickly change the password.
I tried this in the Cat 6509 but found a different result. When I press
enter, it didn't go to console (prompt) instead, it keep asking me the
password.
Is there anything change in the password recovery for Cat 6500 (I've done it
before but when I try it again, it showed a different result). FYI, i use
this version of CatOS = cat6000-sup2k9.7-6-12.bin
Regards,
Affandi Indraji

Hi Friend,
There is no change in the password recovery procedure it is just that you might not be doing it fast enough in 30 seconds.
Just power off and power on the switch again and then immediately try hitting enter as soon as it prompts for the first password and then follow the same procedure what you used to do for other CATOS switches.
HTH, if yes please rate the post.
Ankur

Cat 6500 with DCNM 6.2(1)

Hi there,
for test purposes I installed Cisco Prime DCNM 6.2. It works great with out Nexus 5k and 7k, however I have trouble with our older Cat 6500 devices. While I know that support for these devices is limited I am surprised that the portchannels could not be discovered performance wise and in regard to the topology map, even if they are connected to N7k's. Neither the normal portchannel ISLs between different 6500 nor the vPCs between 6500 and N7k appear in the topology, although the switches were successfully discovered and are considered "managable" via snmp and ssh.
Is there anything I need to do to make it work?
Best regards
Pille

Rafael,
I had the same issue. You need to go into ACS and create a custom Shell Profile (Policy Elements > Authorization and Permissions > Device Administration > Shell Profiles), flip to the "Custom Attributes" tab, and add the following:
Attribute: cisco-av-pair
Requirement: Mandatory
Attribute Value: Static
Value: shell:roles="network-admin"
...although if you want a non-admin or DCNM "User" role, you would use the following instead:
Value: shell:roles="network-operator"
Save that. Then make sure your Device Admin Authorization Policy (Access Policies > Access Services > Default Device Admin > Authorization) references that Shell Profile in the "Results" section.
I'm using DCNM version 6.2(5) and this works.
Here's a useful link for more info: http://www.cisco.com/en/US/products/ps9911/products_configuration_example09186a0080bf5512.shtml

How to Configure Transparent caching on Cat 6500 with CSM in bridge mode?

hi.
I found How to Configure Transparent caching on Cat 6500 with CSM in routed mode.
But,
I need help How to Configure Transparent caching on Cat 6500 with CSM in bridge mode?
Please let me know sample configuration.
thanks.

Hi,
I wrote the document you mentioned and I also wrote the one below.
http://www.cisco.com/en/US/partner/products/hw/modules/ps2706/products_configuration_example09186a00802c1201.shtml
The one with the SSLM is a bridge mode config.
If you replace the SSLM with a cache [or a farm of caches] it would be a similar config.
Replace the SSL21 vserver with an HTTP vserver [most important is to keep the vlan configured on each vserver]
Regards,
Gilles.

How to Configure Transparent caching on Cat 6500 with CSM in routed mode

I am trying to configure Transparent caching on Cat 6500 with CSM in routed mode, but facing some problems in it , also I have gone thru the example config on cisco site for transparent caching using CSM on Cat 6500 , but the above does not fit my clients requirement.
The scenario is like
Access Switches - Cat6500 with MSFC & CSM - Internet Router
|
Cache Engines and Real servers
The clients as well as real servers are on seperate VLANs (L3) and the requirement is to load balance the internet traffic using cache engines.
I'd really appreciate any helpful suggestions or any useful links/docs/info on this.
Thanks
kumar

Hello Joerg,
Thanks for the reply.
I have already gone thru the sample config shown by this weblink, however this link refers to configuring transparent caching on the CSM in BRIDGED MODE ( i.e both the client and server vlans are having the same IP address ) but in our case , we have multiple L3 VLANS on the CAT6509 having IP addresses in different SUBNETS , and the Real servers to be used for caching also exist on one of these VLANS. Thus, the scenario described by the Weblink does not apply here. Also , in the configuration referred by the above weblink, the VLAN 100 is configured as client , however the endusers are shown to be on vlan200 which is configured as SERVER VLAN in the CSM.
Dont you think there is something wrong here, I mean the endusers should be on VLAN 100 (Client) and real servers on VLAN 200 (SERVER).
So, I have to configure CSM in routed mode ( i.e both the client and server vlans will have seperate IP addresses in different subnets ) and the endusers will be on all VLANS .
Pls let me know , how I can implement this solution.
Thanks again
Sudhir

Jumbo Frame - Enabling on a VLAN of CAT 6500 running IOS

Jumbo frames needs to be enabled on one of the vlan interface on Cisco 6500 IOS Switch.
=================================================================
•1) Once enabled the mtu 9216 on the required vlan interface do we need to reload the switch to take effect (I believe that in some low end swicthes it needs a reload)
•2) If we enable only one Vlan interface, how about the other vlan interfaces(about 200 are on this switch)? Do we need to specify mtu1500 on other vlan interfaces?
I have read information at the following two links, but I still wish to reconfirm by asking the questions in this forum. Someone who has already implemented this may have gained more experience while implementing it on CAT 6500 IOS Switch.
https://supportforums.cisco.com/message/963341#963341
http://www.cisco.com/en/US/products/hw/switches/ps700/products_configuration_example09186a008010edab.shtml
http://www.cisco.com/en/US/products/hw/switches/ps700/products_configuration_example09186a008010edab.shtml#backinfo1
Thanks.
Alphonse

You do not need to reboot your 6500 after you enable jumbo frames, but it is good idea to do it during an outage window. You only need to reboot smaller switches i.e. 3560, 3750, etc...after enabling jumbo frames. On these switches you can only enable it globally. Only enable jumbo frames for the vlans you need. You usually need jumbo frames for vlans connecting to the storage systems.
Good Luck

Multiple RSPAN Vlan on cat 6500

Hi,
Can we create multiple RSPAN Vlans on one switch and span across the same VTP domain ?
I am using Cat 6500 switch.
Is it possible to have multiple RSPAN sessions Simultaneously
require valuable inputs for the same.

Hi
24 max RSPAN sessions

Cat 6500 SupEng MSFC II IOS SLB performance

Hello,
anyone know which are the current cat 6500 Supervisor Engine II MSFC II IOS SLB performance ? I need to know the max tcp/udp cuncurrent active session and the max tcp/udp setup rate.
Thanks a lot.
Best regards
Fabio Bellini

check out the following link for the performance details :
http://www.cisco.com/en/US/products/hw/modules/ps2706/products_data_sheet09186a00800887f3.html

QuickJog 1.0 - Shuttle/Jog Replacement for Premiere CS6... almost

quickJog 1.0 - "fixing what Adobe broke in CS6"
a shuttle/jog replacement for Premiere/Prelude CS6
* see below for download links and instructions *
Introduction
I'll waste no time in expressing my opinion on this one: I loved the jog control in previous versions of Premiere, and a small part of my heart died when I realised that those beloved controls couldn't be reinstated in CS6 (though an ever larger chunk died when I realised that Q and W don't work by default in Prelude... ).
JKL is great as a concept, but in practice, not very responsive - it's difficult to make precise jumps in speed quickly, and I'd hate to log footage in CS6 using the JKL keys alone.
It was whilst reading through a different thread on the forums that I had an idea. Why not just jog with the middle mouse button? REAPER uses a similar idea to great effect for scrubbing.
And so the journey began.
Installing/using quickJog
Pre-requisites
Glovepie is only available for Windows. The script, therefore, only works on Windows.
Sorry Mac users.
To use quickJog, you'll need to download the following:
GlovePie, from glovepie.org. Doesn't matter whether you grab the version with or without emotiv support, as long as it's a recent version
The quickJog script, from bit.ly/getQuickJog (unreserved thanks go to Creative Inlet Films for hosting this)
A mouse with a middle-mouse button/clickable scroll wheel
You'll also need to ensure:
The JKL keys have not been re-mapped in Premiere. This is essential, as quickJog 'presses' the JKL keys to alter the jog speed in Premiere.
Installation/usage
Is currently as simple as...
Start Glovepie
From the File menu, select Open...
Navigate to wherever you unzipped the quickJog script. Open it.
Click the Run button
Click the [ .] button at the end of the menu bar to minimise Glovepie to the system tray
To shuttle, click on the program monitor, source monitor or trim monitor, and scroll the mouse wheel. This functionality is built-into Premiere. You can hold Shift for bigger jumps.
To jog, click and hold the middle-mouse button over the source monitor, program monitor, or timeline, and move left or right to increase/decrese the jog speed (just like the old jog slider).
QuickJog tracks the position of the mouse itself, not the position of your mouse cursor, so don't worry about the cursor touching the edge of your screen.
Keep your eyes on the video, not the mouse!
To exit, right-click the glovePie icon, and select Exit.
quickJog works in Prelude too, which is pretty cool.
Links/Misc
HOW AWESOME WOULD SOME EXTRA BITS OF INFORMATION BE FOR THE WORLD? Like information on how to tweak the configuration variables??
Pretty awesome, I'd say James. Have you thought about actually writing this section, then?
Paha! Don't be crass.
Aww.

I stand humbly informed!
In hindsight, I'm not surprised that the JKL keys are a popular choice amongst editors (especially for those who've moved across from other NLEs), but it does rest somewhat uncomfortably in my heart. It feels like Adobe have replaced the pedals and gearstick in my car with a keyboard: not great for those moments when a child runs into the road.
The Shuttle Pro (and Bella to my knowledge?) controllers emulate left/right arrow keypresses to do their work, making the playback 'glitchy' during shuttle operations - I don't like that. I didn't particularly like the feel of the Shuttle Pro when I tried it either. I do like controllers like this (I have one), but have been working for some time on interfacing between the Sony 9-pin protocol and Premiere.
As such, my intermediate preference has been to use a graphics tablet (with a keyboard) for NLE work - hence why having the jog/shuttle controls on screen was so darn useful! Now that I have quickJog mapped to the stylus eraser, edits are much faster.
Quick aside: Huge commendations on just how much can be mapped to keyboard shortcuts in Premiere, huzzah!

New Macbook a good replacement for 12" Powerbook?

I think, besides the inch in display difference, that the new macbook WOULD HAVE made a GREAT GREAT GREAT replacement for users loving or wanting the portability, yet pro versatility of the old 12" Powerbooks. I think however that Apple has missed the mark in one BIG BIG WAY! Firewire. People who wanted something like the 12" powerbook wanted the power of the Macbook Pro in a smaller package. Apple hit the nail on the head with incorporating the same graphics performance, by using aluminum, by making it lighter, and by putting in the illuminated keyboard (only in the 2.4 model though). But on the last detail, they missed it. Firewire. there is no workaround. period. Why preload the systems with iMovie when you can't import video from MOST modern digital camcorders? WITHOUT EVEN introducing a new port with adapters (like they did with the Display Port). I think I would've sold my old macbook pro and had instantly purchased the new macbook if Apple had just included that one VITAL port. I would even prefer them putting it in the place of one of the two USB ports. But without being able to import video from my NEW minidv, there is just no way i could buy that macbook and call myself a proud mac owner. What kind of digital hub would that be? Isn't your slogan "works right out of the box."...? what do you guys think about the new macbook being a 12" powerbook replacement??

I have the same situation. I wanted to upgrade from my 12" Powerbook and would move up to the 13" screen of the new MacBook (15" is much too big for my needs). Another family member has the 15" Powerbook and has always liked my smaller size. I was ready to order 2 of the 13" MacBooks and was then stunned to see that Firewire was missing. I have a Sony DV camcorder for movies. It appears Apple expects me to use my old Powerbooks to input the video into iMovie and then transfer it over to my new MacBook. This is not the cutting edge Apple Computer Company that I have been a customer of for 25 years.
If Apple wants to add firewire to the new MacBooks, develop a USB / Ethernet to firewire adapter, or add a 13" MacBook Pro (w/ firewire) to the line-up, they will have a customer. Otherwise, I will hold onto my old Powerbooks until this is corrected.

How to change the default SSH port on Cat 6500 WS-SUP720-3B

I have been net searching this question and I find answers relative to other Cisco products but not for the 6500 series. We are running
entservicesk9_wan-mz.122-18.SXF17a.bin and would like to know how to change the default SSH listening port..
Thanks in advance..

Hi Neil,
Normally this is achieved via the "ip ssh port rotary " but unfortunately, this command is not implemented on your platform so ssh will only work on port 22.
Regards,
Nicolas

APEX Listener as a replacement for modplsql ?

Will APEX Listener ever be, or is it able to be now, a replacement for modplsql driven applications that are not APEX. It seems that it already takes care of everything needed to be a full scale modplsql replacement... In all honesty looking to see if it is possible to reduce the future licensing load on some of my clients if they wanted to build more redundancy into their front-end web applications. They wouldn't be reducing what they pay, as they are still in for the Forms installs in app server, but they are inhibited on their redundancy growth outward since adding new licenses to cover these new servers would be cost prohibitive. This is mainly a third-party product (SGHE's Self-Service Banner) that is driven off of modplsql, so rewrite isn't an option.
Thanks for your input,
-Richard

As of the last EA version, it depends on which modplsql features your application uses. The main modplsql features that are not yet supported are:
Basic database authentication - The listener must be configured with a single username and password and cannot dynamically change the database connection at run time.
Multiple DADS - Each listener is configured for one and only one database connection. However, there is a way to install multiple copies of the listener, and configure each for a different database connection.
Dynamic parameter passing - There must be a one to one relationship between fields on an HTML form (or query string variables in the URL) and the non-defaulted parameters of the called procedure. Name and Value arrays, with the "!" before the procedure name in the URL are not supported.
CGI environment variables in the DAD.
Oracle MAY support some or all of these features in the production version, or in some future version. We can probably influence this by telling Oracle what we want - but no guarantees. Kris Rice tells me that the APEX Listener was written to be extendable, so once Oracle gives us some documentation of how to extend it, some enterprising programmer may add some of these features as an extension.

Replacement for dvi to vga adapter for late 2008 17"Macbook pro

Hello,
I have a 17" inch late 2008 mack pro. The apple dvi to vga adapter cable is not working anymore. I can seem to find a replacement for it. I have tried the generic dvi to vga adapter (image attached). This does not work. Please advise

Hello mshameel,
It may help to reset your system's SMC and NVRAM.
Intel-based Macs: Resetting the System Management Controller (SMC)
http://support.apple.com/kb/HT3964
About NVRAM and PRAM
http://support.apple.com/kb/HT1379
Cheers,
Allen

I could not get my iPhone 5 which purchased in Australia repaired by apple in the US. Guys from apple retail store verified a replacement for me and asked to call apple care. However, apple care said they cannot get it fixed nor repaired.

My iPhone 5 got some defects and I went to a apple reatil store yesterday. The guy from the genius bar told me that he verified a replacement for me. And I need to call 1-800-apple care to finish that process. I called apple care and one of the senior supervisors told me that I have to send it back to Australia (where I bought this iPhone) to get it repaired. Turns out I could not solve the problem after a apple store vist and several calls. I just want to know if there any way to solve this. This iPhone is a factory unlocked one that purchased in an apple retail store in Melbourne at the day it was first released. And my experience today is not what I can tell as fair. I will be really appreciate for any helps and advices. Thanks.

Warranty on iPhone is not international, but valid only in country of
original sale. Since you purchased the iPhone in Australia, your warranty
is valid only in Australia. You must either personally return the iPhone
to Australia for evaluation and possible replacement or sent it to someone
in Australia to take into Apple for the evaluation. Apple will not accept
international shipments for repair nor will Apple ship out of the country
after replacement.
Sorry to be the bearer of this news, but it is the way iPhone warranty and
replacement has always worked.

Replacement for Cat 6500

Similar Messages

Maybe you are looking for