Replacement macbook has loud beep again when I click on isight in imovie.

was sent a replacement mac for this very reason and my new one is doing the exact same loud beep. It really scares the you know what out of me every time it goes off. Spent over an hour on the phone with applecare and tried to take the battery out and reset whatever that was like they told me and still nothing. Does anyone have a way to fix this?

You know, I tried to email you and it said I had to know your email...***. Ok, by turning down the volumes it really turns your computer down but at least this works for now. The product specialist called me back and he said that it sounds like some type of feedback problem so he is going to talk to the engineers and give me a call back in few days or by next week.
Ok, go to System Peferences and where ever both of the volumes are now, cut it in half. Worked for me except the volume is really low.
I'll keep you posted when my product specialist calls back.
Is everything else fine on your mac? Everything else works beautifully on mine. The first macbook would tap right click or recognize CDs right away and the internet was rrreeeaaalllyyy slow.

Similar Messages

  • HT2497 Mail,contacts & calendar is telling me for I'd password but is not working and just has a beep noise when I click on sighn out or ok??

    I can't remove this icloud password window from my screen??

    Hi Ethan6661,
    Thanks for visiting Apple Support Communities.
    If you do not have access to the computer you normally sync with, it may be necessary to use one of these methods to erase your phone and remove the passcode:
    iOS: Forgotten passcode or device disabled after entering wrong passcode
    http://support.apple.com/kb/HT1212
    If you see one of following alerts, you need to erase the device:
    "iTunes could not connect to the [device] because it is locked with a passcode. You must enter your passcode on the [device] before it can be used with iTunes."
    "You haven't chosen to have [device] trust this computer"
    If you have Find My iPhone enabled, you can use Remote Wipe to erase the contents of your device. If you have been using iCloud to back up, you may be able to restore the most recent backup to reset the passcode after the device has been erased.
    Alternatively, place the device in recovery mode and restore it to erase the device:
    Disconnect the USB cable from the device, but leave the other end of the cable connected to your computer's USB port.
    Turn off the device: Press and hold the Sleep/Wake button for a few seconds until the red slider appears, then slide the slider. Wait for the device to shut down.
    While pressing and holding the Home button, reconnect the USB cable to the device. The device should turn on.
    Continue holding the Home button until you see the Connect to iTunes screen.
    iTunes will alert you that it has detected a device in recovery mode. Click OK, and then restore the device.
    Best,
    Jeremy

  • I updated my billing information, but I still can't access Photo Shop.  It gives me the message to contact Manager Subscription over and over again, when I click on the Try  Again sign.  How can I proceed?

    I updated my billing information, but it won't take the new credit card.  AND every time I go back to Photo Shop to do my work it gives me the message to go to Subscription Manager over and over again, when I click on the Try Again sign.  How can I proceed past it and do my work?

    Unfortunately, only Adobe customer service can assist you with your issue. These are user forums; you are not addressing Adobe here.
    Click on the link below, and after that click on "Still need Help? Contact us."
    Then on the next page, click Chat.
    There is also a phone option. 1 (800) 833-6687
    http://helpx.adobe.com/contact.html?step=PHXS_downloading-installing-setting-up_licensing- activation

  • I have added more songs to my library. Half of the library has selected ticks but when I click on any of the others to select them the whole song disappears from the list. Why and what can I do to fix?

    I have added more songs to my library. Half of the library has selected ticks but when I click on any of the others to select them, the whole song disappears from the list. Why and what can I do to fix?

    Hey Paul,
    If I understand correctly, it sounds like iTunes is not grouping the songs from a particular CD together. The cause could be something as minor as a misspelling or slight variations. For more information, see the following resource:
    Why aren't songs with the same album art grouped together?
    http://support.apple.com/kb/TS1468
    Thanks,
    Matt M.

  • Itunes says it has available updates but when I click download updates, it says no available update.

    Itunes says it has available updates but when I click download updates, it says no available update.

    This happened to me as well. I use an iMac as my main machine, but have a laptop that my daughter uses. I use my Apple ID on both computers. I would occasionally see on my iMac that I have updates available and would click update and get the No Update Available response, yet the red badge remains displaying that I have an update. Found that a few people had this happening as well via these forums so I checked on the laptop and it updated. I then noticed the red badge on the iMac had disappeared as well. If you have any other computers that share your Apple ID, I'd run update on those to see if it fixes your issue.
    Thanks,
    Bryan

  • MacBook Pro three beeps again

    Hello, my 2011 MacBook Pro had what I believed to be a ram issue. It gave the three beeps. It would freeze and give the three beeps. So I purchased new ram (same as before ). Everything was working we'll for about a month. Then yesterday it gave me three beeps again. I spent 100 dollars on the ram, and I don't know what to do. Any help on what the problem is, or what to do is greatly appreciated, thank you.

    That is a ram failure signal.  Where did you get the ram?  The Mac specialialist suppliers guarantee the ram to work and will replace it.  You need to deal with suppliers like OWC, http://www.macsales.com

  • Macbook Air Loud Beeping!

    Hi there,
    I have become concerned lately, I have been finding that when I close my macbook air so that it goes on sleep, it will sound a fast and loud beep when it actually goes to sleep (not straight when the lid is closed). This is usually when it is plugged in.
    However, sometimes when its not plugged in, and I may pick it up off a desk, or tilt it sideways to find the USB port, it will also make this loud beep. It's a little embarrassing in lectures!
    Is there a problem with my hard drive or something? I have gone into utilities and used the disk utility to check my hard drive status, and it just says OK.
    It never used to do this when I first bought this in Feb/March!
    Any ideas?

    Hi LeonJ,
    A beep of any sort, outside of a POST chime on startup (which is more of a chime, than a beep) is not normal. There are diagnostic "beeps" built into the EFI firmware of Intel-based Apple computers used for diagnostics of component failure. Although typically the beep is on startup, not on sleep or shutdown.
    Whereas Pappy's issue sounds more inline with when the beep should occur. Here are a few articles on some of the noise/LED-based diagnostics for the MacBook Air. But as iSMH previously identified, a service call might be the best solution. Even if it's a phone call into support for initial diagnosis.
    Article 1 - http://support.apple.com/kb/HT1221
    Article 2 - http://support.apple.com/kb/HT2130
    Article 3 - http://support.apple.com/kb/HT1547

  • Pavilion dv6 - loud beeping sound when starting +sound problem

    i just bought an hp pavilion dv6 notebook LR732PA and every time i turn it on there's a loud beeping sound, and i'm not sure if this is normal but it asks me where to boot from (pc hard drive) and which oS (windows 7 64-bit). does anyone know how to stop the beeping?
    Also sometimes the sound stops working altogether and an icon appears on the screen with a circle moving around it, and when i try to put the volume up the bar slides back down. it usually can be fixed by closing some programs and processes, it happens sometimes when ive just got 2 programs running and i close one and its ok, or if its not i have to restart. is this something to do with RAM or some kind of sound setting?
    Thanks =)

    There could possibly be a RAM issue here are a couple of troubleshooting links that might resolve your issue or give you an idea what the beeping is referring to.
    http://h10010.www1.hp.com/ewfrf/wc/document?lc=en&dlc=en&cc=us&docname=c01732674&product=1132551#N16...
    http://h20000.www2.hp.com/bizsupport/TechSupport/Document.jsp?objectID=tis13707 
    Clicking the White Kudos star on the left is a way to say Thanks!
    Clicking the 'Accept as Solution' button is a way to let others know which steps helped solve the problem!

  • Loud beep sound when starting up my Mac book air (2007), right before the classic start-up noise

    There is a very loud beep right before the classic Mac start up "bong"
    I'm thinking there might be something wrong with the ram...
    Any answers? Thanks!

    Although it's an older article, for the most part it's applicable -
    http://support.apple.com/kb/HT2538
    The beep on startup is usually an indication of a failed RAM module. It's also possible that a recent firmware update on the machine was botched. If you didn't recently perform a firmware update then it's probably the RAM. As the RAM is soldered directly to the logic board it cannot be replaced individually, it'd require a full logic board replacement.
    Given the age of the machine, it's unlikely still covered by the AppleCare Protection Plan and definitely not the one year limited warranty.
    The next course of action would be to bring the machine into the Genius Bar or AASP and have them evaulate your repair options.

  • Firefox has started freezing up when I click on bookmarks

    This problem started yesterday (June 7th) when I clicked on a forum thread that had some embedded video's, thinking nothing of it I force quit firefox and restarted it. Then later on I tried to access my bookmarks however when I clicked on it to bring up the list firefox froze again forcing me to again force quit and restart.
    Since then I've discovered that I can't click on File, Edit, View, History, Bookmarks, Help or any of my RSS feeds without Firefox immediately freezing up. Even right-clicking in the browser causes it to freeze up.
    As you might imagine this is very annoying and a little worrying as well.
    The only change to my software was an update to my Ubuntu10.04 LTS OS yesterday (June 7th). Though the problem I'm having didn't start up until about 6 hours after the update. I've also tried updating Firefox but the problem still persists.

    You can check for problems with the <b>places.sqlite</b> database file in the Firefox profile folder.
    *http://kb.mozillazine.org/Bookmarks_history_and_toolbar_buttons_not_working_-_Firefox
    *https://support.mozilla.org/kb/Bookmarks+not+saved#w_fix-the-bookmarks-file
    *Places Maintenance: https://addons.mozilla.org/firefox/addon/places-maintenance/
    If possible that please update to the current Firefox 29 release (Firefox 30.0 will be released next Tuesday).
    Note that your System Details List shows multiple Flash plugins.
    # Shockwave Flash 11.2 r202
    # Shockwave Flash 9.0 r999
    You can find the installation path of all plugins on the <b>about:plugins</b> page and remove the Shockwave Flash 9.0 r999 version.
    *http://kb.mozillazine.org/Issues_related_to_plugins#Identifying_installed_plugins
    You can find the latest Flash player here (Linux: Flash Player 11.2.202.359).
    *http://www.adobe.com/special/products/flashplayer/fp_distribution3.html

  • HT204053 just bought iMac, shop has installed facetime but when i click in i can see my face but when i ring one of my contacts the destinatory doesnt hear the ringing tone?

    just bought imac, the shop has installed  facetime, but when i dial one of my contacts, receiver doesnt hear the ringing tone....simply doesnt work, have tried to call even my ephone. same story, can someone helps?tks

    Hi AUDREY1410,
    Thanks for visiting Apple Support Communities.
    See this article for help with troubleshooting FaceTime:
    FaceTime for Mac: Troubleshooting FaceTime
    http://support.apple.com/kb/ts4185
    Cheers,
    Jeremy

  • Macbook pro 2008 beeping noises when base of laptop is not on flat surfaces. Also typing randomly zero's, it think maybe something is loose. Anyone heard of this before?

    I bought it refurbished a couple of years ago, been fine in genral. Last couple of months i noticed when different preasure is placed on the bottom of the laptop it is beeping very loudly until i find a flat enough position for it to sit on. Along with this it types zeros into anything i am writing.
    Any one had problems likes this or think of a reason for please help me.

    My first guess is your battery is swollen. Do you notice any distortion of the bottom part of the case?
    2008 MBP has a battery that is user replaceable, so try running the MBP without the battery using the AC adapter.
    If in fact a swelling battery is the culprit, the only real solution is to replace it.

  • MacBook makes repeated beeping noise when attempting to turn on?

    My MacBook ran out of battery. When I went to power it on it makes a loud repeating beeping sound and will not power on. Anyone have any ideas or heard of this problem before?

    Power On Self-Test Beep Definition - Part 2

  • My Macbook has a Kernel Panic when trying to boot from Mac OS Install DVD

    It might also be relevant that my Accounts Preference Panel crashes System Preferences when I try to open it. Disk Utility sees no problems with my drive, and booting into single user mode and doing a disk check has no results.
    I am running a 2010 Macbook
    2GB Ram
    2.4 Duel Core Processor
    Mac OS 10.6.8
    Windows Installed Via Bootcamp, but problems occured before Windows was installed as well.
    Anything Else that I need to add?

    Try reinstalling Snow Leopard. If you continue getting a kernel panic booting from the DVD, then either you have a bad installer disc or you have a hardware failure.
    Reinstall OS X without erasing the drive
    Do the following:
    1. Repair the Hard Drive and Permissions
    Boot from your Snow Leopard Installer disc. After the installer loads select your language and click on the Continue button. When the menu bar appears select Disk Utility from the Utilities menu. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list.  In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive.  If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported click on the Repair Permissions button. Wait until the operation completes, then quit DU and return to the installer.
    If DU reports errors it cannot fix, then you will need Disk Warrior and/or Tech Tool Pro to repair the drive. If you don't have either of them or if neither of them can fix the drive, then you will need to reformat the drive and reinstall OS X.
    2. Reinstall Snow Leopard
    If the drive is OK then quit DU and return to the installer.  Proceed with reinstalling OS X.  Note that the Snow Leopard installer will not erase your drive or disturb your files.  After installing a fresh copy of OS X the installer will move your Home folder, third-party applications, support items, and network preferences into the newly installed system.
    Download and install the Combo Updater for the version you prefer from support.apple.com/downloads/.

  • My Macbook Has A Prohibited Logo When It Loads, Then It Goes Straight To My Windows Virtual Account Which Works

    It started when my macbook froze while I had a video open, I turend it off by the switch and it's not been loading since then.The only thing that seems to be different on my windows acount is that I can't use the wifi from my room. Which is the first time I've had this problem since my interent's pretty deacent.  I tried to reset the "PRAM" and "NVRAM" and it didn't work. I couldn't seem to open it in safe mode,and when I tried to manually put in a command it froze and I wasn't able to type in a command.

    Hi LocPLe, and a warm welcome to the forums!
    Hmm, try these steps...
    Resetting MacBook and MacBook Pro System Management Controller (SMC)...
    http://docs.info.apple.com/article.html?artnum=303319
    Try holding the Option key, or Space Bar down for a boot up.
    "Try Disk Utility
    1. Insert the Mac OS X Install disc that came with your computer, then restart the computer while holding the C key.
    2. When your computer finishes starting up from the disc, choose Disk Utility from the Installer menu. (In Mac OS X 10.4 or later, you must select your language first.)
    *Important: Do not click Continue in the first screen of the Installer. If you do, you must restart from the disc again to access Disk Utility.*
    3. Click the First Aid tab.
    4. Click the disclosure triangle to the left of the hard drive icon to display the names of your hard disk volumes and partitions.
    5. Select your Mac OS X volume.
    6. Click Repair. Disk Utility checks and repairs the disk."
    http://docs.info.apple.com/article.html?artnum=106214
    Then try a Safe Boot, (holding Shift key down at bootup), run Disk Utility in Applications>Utilities, then highlight your drive, click on Repair Permissions, reboot when it completes.

Maybe you are looking for