Replacing a failed UCS FI node
We've had a hardware failure on one of our FI nodes in a UCS cluster. I installed the replacement unit, updated firmware to match the existing node and configured it to join the cluster. Next step is to reconnect LAN, SAN, and swap the expansion modules. My question is if this will cause an outage or any connectivity loss for the primary, functioning node.
Thank you
We've had a hardware failure on one of our FI nodes in a UCS cluster. I installed the replacement unit, updated firmware to match the existing node and configured it to join the cluster. Next step is to reconnect LAN, SAN, and swap the expansion modules. My question is if this will cause an outage or any connectivity loss for the primary, functioning node.
Thank you
Similar Messages
-
Hey, I am currently migrating my cluster.
I removed the server pool master according to the metalink note by doing a failover (stopped the agent on the server pool master)
Deleted the old master (node2) from the server pool.
Executed the cleanup script on node2 and switched it off
Modified the cluster.conf on the remaining node and remove the entries for the old master node2.
Replaced the old server with new hardware -
same name - same ip.
Now I try to add this server to the server pool, but I get a timeout message
OVM-1006 Register Oracle VM Server (node2) Failed: errcode=00001, errmsg=CDS accquire lock /etc/ovs-agent/db/srv.lock timeout. locker process is 8339
Where can I look ?
ChristianLemeunier wrote:
> environment: sles 10 sp3, oes2, cluster services
>
> problem: reconfiguring oes to add a node to the cluster is causing the
> error *failed to add node to cluster*
>
> history: I installed a 4 node cluster in a HP C7000 blade. We had to
> replace the network switch in the blade center by a virtual connect
> flex-10. This resulted in a loss of network connectivity, so I removed 3
> of 4 nodes from cluster and eDirectory.
> This worked fine, replication and time synchronisation was succesfully
> and all server objects belonging to these 3 servers were deleted.
>
> Now the new switch has been configured and network connection
> reestablished. Reconfiguring eDirectory and other oes2 services
> succeeds, alle server objects are recreated, eDirectory is in sync, but
> reconfiguring cluster services does not succeed.
>
> What do I have to do, to reconfigure cluster service and add nodes to
> the cluster?
>
> Thank you for all hints.
>
> Ursula
>
>
Did you remove the cluster rpms and then reinstall the rpms. I would
recommend following TID 3131978 and see if that helps. -
I need helop with my ALSB Replace action failed updating variable
System Error Handler
$fault:
<con:fault xmlns:con="http://www.bea.com/wli/sb/context">
<con:errorCode>BEA-382513</con:errorCode>
<con:reason>
ALSB Replace action failed updating variable "body": Error parsing XML: {err}XP0006: "element {http://rep.oio.dk/tinglysning.dk/svarservice/message/anmeldelse/1/}AndelsbogAnmaerkningStatusModtag { {http://www.w3.org/2004/07/xpath-datatypes}untypedAny }": bad value for type element {http://rep.oio.dk/tinglysning.dk/schema/anmeldelse/1/}AndelsbogAnmaerkningStatus { {http://www.w3.org/2001/XMLSchema}anyType }
</con:reason>
<con:location>
<con:node>PipelinePairNode1</con:node>
<con:pipeline>PipelinePairNode1_response</con:pipeline>
<con:stage>stage1</con:stage>
<con:path>response-pipeline</con:path>
</con:location>
</con:fault>
Edited by: user543916 on Jun 28, 2011 2:28 AMyou should report also the content of the variable you were trying to assign to $body, and which element in $body you were trying to modify.
-
I am attempting to replace a failed hard drive on a F500 Vista laptop. I have a home premium recovery DVD (1 of 1) and It runs the recovery after a while of loading, and it creates a 24GB partion and loads about 2.6Gb of information on it. the it ejects the disc and asks if I have any suplimental disks, which I don't have. Then it reboots it's self and cycles through reboots for 5 hours, yes I let it do this for 5 hours as the HP site says it could take several hours.
After this I finally shut down the computer and loaded the hard drive in an ext case and retrieved the above information. I also note that the 250GB drive is shown as a 24GB drive, so I guess it hasn't completed the partions?
I never get to a Vista window.
This hard drive does pass the laptop's Bios hard drive check (the former 80GB drive did NOT) and was used to store Old Time Radio shows, until I went to a larger drive.
The Laptop has a dual core Athlon TK-53 processor and the recovery disc is for 32 bit Vista (and the label in front and license on back don't state Vista 64, just Vista)
So, Do I need a Vista 64 recovery disc? Should I download the available driver on the HP site and slap in that disc when the Recovery disc finishes and asks for supplimental discs? Might thngs indicate other issues with the laptop?
I've loaded from scratch XP several times, but this is my 1st Vista experience. Thank you for any help!Okay. So I was able to install, and format the new internal HD. Was able to install Lion then Mavericks. Next, is to try to retrieve my data from my failing old HD. I bought an enclosure (sled), and have my HD hooked up to my laptop, and it finally showed up in Finder. So. Now. What is next? I am seeing a screen that shows these folders: Applications (translate for the PC me = Programs), Library (I am assuming?? these are my various files such as docs, photos, music, etc.) System, opt, and Users. Should I just try to drag and drop some/all of the folders onto my desktop, then open up the folders and do something with the contents? Sorry to sound so vague and frankly, rather dumb-sounding, but the nomenclature with a Mac is a bit different than with a PC, and Finder is a little different looking to me than Windows Explorer. I am relieved to see that I was even able to get this failing drive to show up in the first place, so I feel a little like I could be on borrowed time with it. I think it may just be bad sectors, since I don't hear any clicking or other mechanical issues with the drive as it spins. But, any further help with retrieving the data would be VERY much appreciated!!
-
Root.sh failed on second node while installing CRS 10g on centos 5.5
root.sh failed on second node while installing CRS 10g
Hi all,
I am able to install Oracle 10g RAC clusterware on first node of the cluster. However, when I run the root.sh script as root
user on second node of the cluster, it fails with following error message:
NO KEYS WERE WRITTEN. Supply -force parameter to override.
-force is destructive and will destroy any previous cluster
configuration.
Oracle Cluster Registry for cluster has already been initialized
Startup will be queued to init within 90 seconds.
Adding daemons to inittab
Expecting the CRS daemons to be up within 600 seconds.
Failure at final check of Oracle CRS stack.
10
and run cluvfy stage -post hwos -n all -verbose,it show message:
ERROR:
Could not find a suitable set of interfaces for VIPs.
Result: Node connectivity check failed.
Checking shared storage accessibility...
Disk Sharing Nodes (2 in count)
/dev/sda db2 db1
and run cluvfy stage -pre crsinst -n all -verbose,it show message:
ERROR:
Could not find a suitable set of interfaces for VIPs.
Result: Node connectivity check failed.
Checking system requirements for 'crs'...
No checks registered for this product.
and run cluvfy stage -post crsinst -n all -verbose,it show message:
Result: Node reachability check passed from node "DB2".
Result: User equivalence check passed for user "oracle".
Node Name CRS daemon CSS daemon EVM daemon
db2 no no no
db1 yes yes yes
Check: Health of CRS
Node Name CRS OK?
db1 unknown
Result: CRS health check failed.
check crsd.log and show message:
clsc_connect: (0x143ca610) no listener at (ADDRESS=(PROTOCOL=ipc)(KEY=OCSSD_LL_db2_crs))
clsssInitNative: connect failed, rc 9
Any help would be greatly appreciated.
Edited by: 868121 on 2011-6-24 上午12:31Hello, it took a little searching, but I found this in a note in the GRID installation guide for Linux/UNIX:
Public IP addresses and virtual IP addresses must be in the same subnet.
In your case, you are using two different subnets for the VIPs. -
HT1338 How to install OS X on a new HDD to replace a failed drive?
My sisters MacBook (Late 2006) HDD has failed. I have a spare drive that I would like to install OS X onto to replace the failed drive. Whats the best way to do this and which version of OS is best to install for this model MacBook?
Hello, it'd be best to use the Original Install Disc while booting the MacBook from it, but a Retail 10.6 Install Disc may work...
Snow Leopard/10.6.x Requirements...
General requirements
* Mac computer with an Intel processor
* 1GB of memory (I say 4GB at least, more if you can afford it)
* 5GB of available disk space (I say 30GB at least)
* DVD drive for installation
* Some features require a compatible Internet service provider; fees may apply.
* Some features require Apple’s MobileMe service; fees and terms apply.
Which apps work with Mac OS X 10.6?...
http://snowleopard.wikidot.com/
Buy Snow Leopard > http://store.apple.com/us/product/MC573/mac-os-x-106-snow-leopard
Call Apple Sales...in the US: 1-800-MY-APPLE. Or Support... 1-800-275-2273
Other countries...
http://support.apple.com/kb/HE57 -
Is it possible to replace a failed drive with another unused hard drive within an ix12-300r
I have an ix12-300r with a failed drive in a storage pool - I want to replace the failed drive with one of the other drives in the NAS that are unused (i.e. not part of any other storage pool)
i.e. Storage Pool consists of 3 drives - disk 1, disk 2 and disk 3.
Disk 3 has failed.
Disk 4 is free and not used by any other storage pool.
Can Disk 4 be pulled out and then put into the place of Disk 3?
(All disks are the same model/size/speed)Hello cayliffe
Yes! In you case disk 4 would be usable as a replacement for disk 3.
You can remove disk 4 and put it in bay 3 if you wish, however you should be able to set the ix12 to use unused drives as hot spares so the firmware switches to the disk automatically. In Drive Management > Settings the "Use available drives as hot spares" option will allow your device to use any compatible unused/available disk as a hot spare for any of the storage pools.
LenovoEMC Contact Information is region specific. Please select the correct link then access the Contact Us at the top right:
US and Canada: https://lenovo-na-en.custhelp.com/
Latin America and Mexico: https://lenovo-la-es.custhelp.com/
EU: https://lenovo-eu-en.custhelp.com/
India/Asia Pacific: https://lenovo-ap-en.custhelp.com/
http://support.lenovoemc.com/ -
Replacing a value of a node with CDATA (as is)
Hi All,
How do I replace the value of a node such that it's CDATA format is preserved and not re-encoded. Currently, when I do similar to the following:
replace value of node doc(doc_name)/parent/node with "<![CDATA[[the data]]]>"
the less than and greater than signs are replaced with < ; and > ; respectively, losing its CDATA section status.
How do I replace the value such that within the resulting XML it is exactly "<![CDATA[[the data]]]>" and not "< ;[CDATA[]the data]]> ;" ?
Thanks in advance
Cecil
Edited by: user5969022 on Jan 8, 2009 9:41 PM
Edited by: user5969022 on Jan 8, 2009 9:42 PM
Edited by: user5969022 on Jan 8, 2009 9:44 PM
Edited by: user5969022 on Jan 8, 2009 9:45 PMJohn,
I am aware that it's synatic sugar. However, I actually need it to look that way. Thing is after edits, the resulting XML will be read by a component (that I have no access to change) which requires that node to have CDATA (as is) as it's value.
Anymore ideas; Anyone?
Instead of replacing the value (ie. replace value of node doc()...), I replaced the node (ie. replace node doc()...) with something similar to: <node>CDATA-section</node>. However, as expected only the data within the CDATA section gets persisted.
In this case could I turn something off or on such that xmldb leaves the CDATA-section as is? e.g. http://www.xquery.com/tips_and_tricks/including_CDATA_in_results.html
Thanks,
Cecil -
Root.sh failed in one node - CLSMON and UDLM
Hi experts.
My enviroment is:
2-node SunCluster Update3
Oracle RAC 10.2.0.1 > planning to upgrade to 10.2.0.4
The problem is: I installed the CRS services on 2 nodes - OK
After that, running root.sh fails in 1 node:
/u01/app/product/10/CRS/root.sh
WARNING: directory '/u01/app/product/10' is not owned by root
WARNING: directory '/u01/app/product' is not owned by root
WARNING: directory '/u01/app' is not owned by root
WARNING: directory '/u01' is not owned by root
Checking to see if Oracle CRS stack is already configured
Checking to see if any 9i GSD is up
Setting the permissions on OCR backup directory
Setting up NS directories
Oracle Cluster Registry configuration upgraded successfully
WARNING: directory '/u01/app/product/10' is not owned by root
WARNING: directory '/u01/app/product' is not owned by root
WARNING: directory '/u01/app' is not owned by root
WARNING: directory '/u01' is not owned by root
clscfg: EXISTING configuration version 3 detected.
clscfg: version 3 is 10G Release 2.
Successfully accumulated necessary OCR keys.
Using ports: CSS=49895 CRS=49896 EVMC=49898 and EVMR=49897.
node <nodenumber>: <nodename> <private interconnect name> <hostname>
node 0: spodhcsvr10 clusternode1-priv spodhcsvr10
node 1: spodhcsvr12 clusternode2-priv spodhcsvr12
clscfg: Arguments check out successfully.
NO KEYS WERE WRITTEN. Supply -force parameter to override.
-force is destructive and will destroy any previous cluster
configuration.
Oracle Cluster Registry for cluster has already been initialized
Sep 22 13:34:17 spodhcsvr10 root: Oracle Cluster Ready Services starting by user request.
Startup will be queued to init within 30 seconds.
Sep 22 13:34:20 spodhcsvr10 root: Cluster Ready Services completed waiting on dependencies.
Adding daemons to inittab
Expecting the CRS daemons to be up within 600 seconds.
Sep 22 13:34:34 spodhcsvr10 last message repeated 3 times
Sep 22 13:34:34 spodhcsvr10 root: Running CRSD with TZ = Brazil/East
Sep 22 13:34:40 spodhcsvr10 root: Oracle CLSMON terminated with unexpected status 10. Respawning
Sep 22 13:35:43 spodhcsvr10 last message repeated 9 times
Sep 22 13:36:07 spodhcsvr10 root: Cluster Ready Services completed waiting on dependencies.
Sep 22 13:36:07 spodhcsvr10 root: Running CRSD with TZ = Brazil/East
Sep 22 13:36:14 spodhcsvr10 su: libsldap: Status: 85 Mesg: openConnection: simple bind failed - Timed out
Sep 22 13:36:19 spodhcsvr10 root: Oracle CLSMON terminated with unexpected status 10. Respawning
Sep 22 13:37:35 spodhcsvr10 last message repeated 11 times
Sep 22 13:37:40 spodhcsvr10 root: Cluster Ready Services completed waiting on dependencies.
Sep 22 13:37:40 spodhcsvr10 root: Running CRSD with TZ = Brazil/East
Sep 22 13:37:42 spodhcsvr10 root: Oracle CLSMON terminated with unexpected status 10. Respawning
Sep 22 13:38:03 spodhcsvr10 last message repeated 3 times
Sep 22 13:38:10 spodhcsvr10 root: Oracle CLSMON terminated with unexpected status 10. Respawning
Sep 22 13:39:12 spodhcsvr10 last message repeated 9 times
Sep 22 13:39:13 spodhcsvr10 root: Cluster Ready Services completed waiting on dependencies.
Sep 22 13:39:13 spodhcsvr10 root: Running CRSD with TZ = Brazil/East
Sep 22 13:39:19 spodhcsvr10 root: Oracle CLSMON terminated with unexpected status 10. Respawning
Sep 22 13:40:42 spodhcsvr10 last message repeated 12 times
Sep 22 13:40:46 spodhcsvr10 root: Cluster Ready Services completed waiting on dependencies.
Sep 22 13:40:46 spodhcsvr10 root: Running CRSD with TZ = Brazil/East
Sep 22 13:40:49 spodhcsvr10 root: Oracle CLSMON terminated with unexpected status 10. Respawning
Sep 22 13:42:05 spodhcsvr10 last message repeated 11 times
Sep 22 13:42:11 spodhcsvr10 root: Cluster Ready Services completed waiting on dependencies.
Sep 22 13:42:12 spodhcsvr10 root: Oracle CLSMON terminated with unexpected status 10. Respawning
Sep 22 13:42:19 spodhcsvr10 root: Cluster Ready Services completed waiting on dependencies.
Sep 22 13:42:19 spodhcsvr10 root: Running CRSD with TZ = Brazil/East
Sep 22 13:42:19 spodhcsvr10 root: Oracle CLSMON terminated with unexpected status 10. Respawning
Sep 22 13:43:49 spodhcsvr10 last message repeated 13 times
Sep 22 13:43:51 spodhcsvr10 root: Cluster Ready Services completed waiting on dependencies.
Sep 22 13:43:51 spodhcsvr10 root: Running CRSD with TZ = Brazil/East
Sep 22 13:43:56 spodhcsvr10 root: Oracle CLSMON terminated with unexpected status 10. Respawning
Failure at final check of Oracle CRS stack.
I traced the ocssd.log and found some informations:
[ CSSD]2010-09-22 14:04:14.739 [6] >TRACE: clssnmDiskStateChange: state from 2 to 4 disk (0//dev/vx/rdsk/racdg/ora_vote1)
[ CSSD]2010-09-22 14:04:14.742 [6] >TRACE: clssnmReadDskHeartbeat: node(1) is down. rcfg(2) wrtcnt(2478) LATS(0) Disk lastSeqNo(2478)
[ CSSD]2010-09-22 14:04:14.742 [7] >TRACE: clssnmDiskStateChange: state from 2 to 4 disk (1//dev/vx/rdsk/racdg/ora_vote2)
[ CSSD]2010-09-22 14:04:14.744 [7] >TRACE: clssnmReadDskHeartbeat: node(1) is down. rcfg(2) wrtcnt(2478) LATS(0) Disk lastSeqNo(2478)
[ CSSD]2010-09-22 14:04:14.745 [8] >TRACE: clssnmDiskStateChange: state from 2 to 4 disk (2//dev/vx/rdsk/racdg/ora_vote3)
[ CSSD]2010-09-22 14:04:14.746 [8] >TRACE: clssnmReadDskHeartbeat: node(1) is down. rcfg(2) wrtcnt(2478) LATS(0) Disk lastSeqNo(2478)
[ CSSD]2010-09-22 14:04:14.785 [1] >TRACE: clssscSclsFatal: read value of disable
[ CSSD]2010-09-22 14:04:14.785 [10] >TRACE: clssnmFatalThread: spawned
[ CSSD]2010-09-22 14:04:14.785 [1] >TRACE: clssscSclsFatal: read value of disable
[ CSSD]2010-09-22 14:04:14.786 [11] >TRACE: clssnmconnect: connecting to node 0, flags 0x0001, connector 1
[ CSSD]2010-09-22 14:04:23.075 >USER: Oracle Database 10g CSS Release 10.2.0.1.0 Production Copyright 1996, 2004 Oracle. All rights reserved.
[ CSSD]2010-09-22 14:04:23.075 >USER: CSS daemon log for node spodhcsvr10, number 0, in cluster NET_RAC
[ clsdmt]Listening to (ADDRESS=(PROTOCOL=ipc)(KEY=spodhcsvr10DBG_CSSD))
[ CSSD]2010-09-22 14:04:23.082 [1] >TRACE: clssscmain: local-only set to false
[ CSSD]2010-09-22 14:04:23.096 [1] >TRACE: clssnmReadNodeInfo: added node 0 (spodhcsvr10) to cluster
[ CSSD]2010-09-22 14:04:23.106 [1] >TRACE: clssnmReadNodeInfo: added node 1 (spodhcsvr12) to cluster
[ CSSD]2010-09-22 14:04:23.129 [5] >TRACE: [0]Node monitor: dlm attach failed error LK_STAT_NOTCREATED
[ CSSD]CLSS-0001: skgxn not active
[ CSSD]2010-09-22 14:04:23.129 [5] >TRACE: clssnm_skgxnmon: skgxn init failed, rc 30
[ CSSD]2010-09-22 14:04:23.132 [1] >TRACE: clssnmInitNMInfo: misscount set to 600
[ CSSD]2010-09-22 14:04:23.136 [1] >TRACE: clssnmDiskStateChange: state from 1 to 2 disk (0//dev/vx/rdsk/racdg/ora_vote1)
[ CSSD]2010-09-22 14:04:23.139 [1] >TRACE: clssnmDiskStateChange: state from 1 to 2 disk (1//dev/vx/rdsk/racdg/ora_vote2)
[ CSSD]2010-09-22 14:04:23.143 [1] >TRACE: clssnmDiskStateChange: state from 1 to 2 disk (2//dev/vx/rdsk/racdg/ora_vote3)
[ CSSD]2010-09-22 14:04:25.139 [6] >TRACE: clssnmDiskStateChange: state from 2 to 4 disk (0//dev/vx/rdsk/racdg/ora_vote1)
[ CSSD]2010-09-22 14:04:25.142 [6] >TRACE: clssnmReadDskHeartbeat: node(1) is down. rcfg(2) wrtcnt(2488) LATS(0) Disk lastSeqNo(2488)
[ CSSD]2010-09-22 14:04:25.143 [7] >TRACE: clssnmDiskStateChange: state from 2 to 4 disk (1//dev/vx/rdsk/racdg/ora_vote2)
[ CSSD]2010-09-22 14:04:25.144 [7] >TRACE: clssnmReadDskHeartbeat: node(1) is down. rcfg(2) wrtcnt(2488) LATS(0) Disk lastSeqNo(2488)
[ CSSD]2010-09-22 14:04:25.145 [8] >TRACE: clssnmDiskStateChange: state from 2 to 4 disk (2//dev/vx/rdsk/racdg/ora_vote3)
[ CSSD]2010-09-22 14:04:25.148 [8] >TRACE: clssnmReadDskHeartbeat: node(1) is down. rcfg(2) wrtcnt(2489) LATS(0) Disk lastSeqNo(2489)
[ CSSD]2010-09-22 14:04:25.186 [1] >TRACE: clssscSclsFatal: read value of disable
[ CSSD]2010-09-22 14:04:25.186 [10] >TRACE: clssnmFatalThread: spawned
[ CSSD]2010-09-22 14:04:25.186 [1] >TRACE: clssscSclsFatal: read value of disable
[ CSSD]2010-09-22 14:04:25.187 [11] >TRACE: clssnmconnect: connecting to node 0, flags 0x0001, connector 1
[ CSSD]2010-09-22 14:04:33.449 >USER: Oracle Database 10g CSS Release 10.2.0.1.0 Production Copyright 1996, 2004 Oracle. All rights reserved.
[ CSSD]2010-09-22 14:04:33.449 >USER: CSS daemon log for node spodhcsvr10, number 0, in cluster NET_RAC
[ clsdmt]Listening to (ADDRESS=(PROTOCOL=ipc)(KEY=spodhcsvr10DBG_CSSD))
[ CSSD]2010-09-22 14:04:33.457 [1] >TRACE: clssscmain: local-only set to false
[ CSSD]2010-09-22 14:04:33.470 [1] >TRACE: clssnmReadNodeInfo: added node 0 (spodhcsvr10) to cluster
[ CSSD]2010-09-22 14:04:33.480 [1] >TRACE: clssnmReadNodeInfo: added node 1 (spodhcsvr12) to cluster
[ CSSD]2010-09-22 14:04:33.498 [5] >TRACE: [0]Node monitor: dlm attach failed error LK_STAT_NOTCREATED
[ CSSD]CLSS-0001: skgxn not active
[ CSSD]2010-09-22 14:04:33.498 [5] >TRACE: clssnm_skgxnmon: skgxn init failed, rc 30
[ CSSD]2010-09-22 14:04:33.500 [1] >TRACE: clssnmInitNMInfo: misscount set to 600
[ CSSD]2010-09-22 14:04:33.505 [1] >TRACE: clssnmDiskStateChange: state from 1 to 2 disk (0//dev/vx/rdsk/racdg/ora_vote1)
[ CSSD]2010-09-22 14:04:33.508 [1] >TRACE: clssnmDiskStateChange: state from 1 to 2 disk (1//dev/vx/rdsk/racdg/ora_vote2)
[ CSSD]2010-09-22 14:04:33.510 [1] >TRACE: clssnmDiskStateChange: state from 1 to 2 disk (2//dev/vx/rdsk/racdg/ora_vote3)
[ CSSD]2010-09-22 14:04:35.508 [6] >TRACE: clssnmDiskStateChange: state from 2 to 4 disk (0//dev/vx/rdsk/racdg/ora_vote1)
[ CSSD]2010-09-22 14:04:35.510 [6] >TRACE: clssnmReadDskHeartbeat: node(1) is down. rcfg(2) wrtcnt(2499) LATS(0) Disk lastSeqNo(2499)
[ CSSD]2010-09-22 14:04:35.510 [7] >TRACE: clssnmDiskStateChange: state from 2 to 4 disk (1//dev/vx/rdsk/racdg/ora_vote2)
[ CSSD]2010-09-22 14:04:35.512 [7] >TRACE: clssnmReadDskHeartbeat: node(1) is down. rcfg(2) wrtcnt(2499) LATS(0) Disk lastSeqNo(2499)
[ CSSD]2010-09-22 14:04:35.513 [8] >TRACE: clssnmDiskStateChange: state from 2 to 4 disk (2//dev/vx/rdsk/racdg/ora_vote3)
[ CSSD]2010-09-22 14:04:35.514 [8] >TRACE: clssnmReadDskHeartbeat: node(1) is down. rcfg(2) wrtcnt(2499) LATS(0) Disk lastSeqNo(2499)
[ CSSD]2010-09-22 14:04:35.553 [1] >TRACE: clssscSclsFatal: read value of disable
[ CSSD]2010-09-22 14:04:35.553 [10] >TRACE: clssnmFatalThread: spawned
[ CSSD]2010-09-22 14:04:35.553 [1] >TRACE: clssscSclsFatal: read value of disable
[ CSSD]2010-09-22 14:04:35.553 [11] >TRACE: clssnmconnect: connecting to node 0, flags 0x0001, connector 1
I believe the main error is:
[ CSSD]2010-09-22 14:04:33.498 [5] >TRACE: [0]Node monitor: dlm attach failed error LK_STAT_NOTCREATED
[ CSSD]CLSS-0001: skgxn not active
And the communication between UDLM and CLSMON. But i don't know how to resolve this.
My UDLM version is 3.3.4.9.
Somebody have any ideas about this?
Tks!Now i finally installed CRS and run root.sh without errors (i think that problem is in some old file from other instalation tries...)
But now i have another problem: When install DB software, in step to copy instalation to remote node, this node have some failure in CLSMON/CSSD daemon and panicking:
Sep 23 16:10:51 spodhcsvr10 root: Oracle CLSMON terminated with unexpected status 138. Respawning
Sep 23 16:10:52 spodhcsvr10 root: Oracle CSSD failure. Rebooting for cluster integrity.
Sep 23 16:10:52 spodhcsvr10 root: [ID 702911 user.alert] Oracle CSSD failure. Rebooting for cluster integrity.
Sep 23 16:10:51 spodhcsvr10 root: [ID 702911 user.error] Oracle CLSMON terminated with unexpected status 138. Respawning
Sep 23 16:10:52 spodhcsvr10 root: [ID 702911 user.alert] Oracle CSSD failure. Rebooting for cluster integrity.
Sep 23 16:10:56 spodhcsvr10 Cluster.OPS.UCMMD: fatal: received signal 15
Sep 23 16:10:56 spodhcsvr10 Cluster.OPS.UCMMD: [ID 770355 daemon.error] fatal: received signal 15
Sep 23 16:10:59 spodhcsvr10 root: Oracle Cluster Ready Services waiting for SunCluster and UDLM to start.
Sep 23 16:10:59 spodhcsvr10 root: Cluster Ready Services completed waiting on dependencies.
Sep 23 16:10:59 spodhcsvr10 root: [ID 702911 user.error] Oracle Cluster Ready Services waiting for SunCluster and UDLM to start.
Sep 23 16:10:59 spodhcsvr10 root: [ID 702911 user.error] Cluster Ready Services completed waiting on dependencies.
Notifying cluster that this node is panicking
The instalation in first node continue and report error in copy to second node.
Any ideas? Tks! -
OSB replace action failed..
very urgent help needed.
Scenario:
1. My proxy service (new wsdl based) calls business (legacy wsdl based).
2. I want to transform input format from new format schema to legacy format schema.
3. I write a Xquery and Replace ./* in variable body with Xquery. Binding variable is accepted as $body.
4. Individually tested, works like a charm; but when proxy is exected-throws following error:
BEA-382513: OSB Replace action failed updating variable "body": line 29, column 1: {err}XP0006: "element {http://schemas.xmlsoap.org/soap/envelope/}Body { {http://www.w3.org/2004/07/xpath-datatypes}untypedAny }": bad value for type element {http://myURL}SwapnilRequest { {http://www.w3.org/2001/XMLSchema}anyType }
here myURL is namespace defined for input format "SwapnilRequest".
In short, the content of variable "body" are not changed even after transformation.
Please help.
Thanks and Regards,
Swapnil Kharwadkar.Dear Eric,
Following is Xquery:
(:: pragma bea:global-element-parameter parameter="$aMA_UpdateRQ1" element="ns0:AMA_UpdateRQ" location="AMA_UpdateRQ.xsd" ::)
(:: pragma bea:schema-type-return type="ns1:ListOfAyLoyMemberPortalProspectTopElmt" location="AY%20LOY%20Member%20Portal%20Prospect_blore.wsdl" ::)
declare namespace ay = "http://www.siebel.com/xml/AYRES%20Member%20Information%20–%20Long%20Portal";
declare namespace com = "http://com.finnair";
declare namespace asi = "http://siebel.com/asi/";
declare namespace xf = "http://tempuri.org/GetNewCard_WithSiebel_XQuery/A_getProfile_Xquery/newResponse/";
declare namespace pros="http://com.finnair/prospectProcessing/";
declare function xf:A_blore_QueryByExample_Request($AMA_UpdateRQ as element(com:AMA_UpdateRQ))
as element(asi:ListOfAyLoyMemberPortalProspectTopElmt) {
let $AMA_UpdateRQ := $AMA_UpdateRQ
return
<asi:ListOfAyLoyMemberPortalProspectTopElmt>
<ay:ListOfAyLoyMemberPortalProspect>
<ay:Contact>
<ay:Id>{ data($AMA_UpdateRQ/com:UniqueID/@ID) }</ay:Id>
<ay:ContactId>{ data($AMA_UpdateRQ/com:UniqueID/@ID) }</ay:ContactId>
</ay:Contact>
</ay:ListOfAyLoyMemberPortalProspect>
</asi:ListOfAyLoyMemberPortalProspectTopElmt>
declare variable $AMA_UpdateRQ as element() external;
xf:A_blore_QueryByExample_Request($AMA_UpdateRQ) -
Has anyone ever been quoted more than $500 to replace a failed logic board?
Has anyone ever been quoted more than $500 to replace a failed logic board? A Genius buddy of mine swears that it'll never be over $500 but I' convinced he's high out of his mind.
I doubt it. They don't even take the same kind of RAM.
What makes you think a replacement "will most likely go bad in the future"? Some have had to go back more than once; many haven't. (And many have not gone in at all.) There are many iBook users out there, happily iBooking away without any knowledge of the iBook Logic Board Repair Extension Program because they've never had a problem.
Get it replaced, free, NOW, and worry about the future when it gets here.
http://www.apple.com/support/ibook/faq/
P.S. When you make an error in a post, there is a little edit-pencil icon next to the "Reply" icon in your post. The edit pencil stays there for about 15 minutes to allow you to edit your post. Just click on it, and it takes you back to your message box so you can edit it to your heart's content. -
Replace a failed boot disk managed by SVM
Hi,
I'm new to SVM and would like to seek assistance in replacing a failed boot disk on a SunFire V490. The disk is managed by SVM.
Would anyone have a list of the steps/commands in order that will need to be followed in order to replace a failed boot disk that is managed by SVM?
Here is the output of 'metastat' and 'metadb' from my system (sorry for the long message):
metadb -i
flags first blk block count
Wm p l 16 8192 /dev/dsk/c2t0d0s7
W p l 8208 8192 /dev/dsk/c2t0d0s7
a p luo 16 8192 /dev/dsk/c2t1d0s7
a p luo 8208 8192 /dev/dsk/c2t1d0s7
metastat
d34: Mirror
Submirror 0: d14
State: Needs maintenance
Submirror 1: d24
State: Okay
Pass: 1
Read option: roundrobin (default)
Write option: parallel (default)
Size: 102411264 blocks (48 GB)
d14: Submirror of d34
State: Needs maintenance
Invoke: metareplace d34 c2t0d0s4 <new device>
Size: 102411264 blocks (48 GB)
Stripe 0:
Device Start Block Dbase State Reloc Hot Spare
c2t0d0s4 0 No Maintenance Yes
d24: Submirror of d34
State: Okay
Size: 102411264 blocks (48 GB)
Stripe 0:
Device Start Block Dbase State Reloc Hot Spare
c2t1d0s4 0 No Okay Yes
d33: Mirror
Submirror 0: d13
State: Needs maintenance
Submirror 1: d23
State: Okay
Pass: 1
Read option: roundrobin (default)
Write option: parallel (default)
Size: 40968576 blocks (19 GB)
d13: Submirror of d33
State: Needs maintenance
Invoke: metareplace d33 c2t0d0s3 <new device>
Size: 40968576 blocks (19 GB)
Stripe 0:
Device Start Block Dbase State Reloc Hot Spare
c2t0d0s3 0 No Maintenance Yes
d23: Submirror of d33
State: Okay
Size: 40968576 blocks (19 GB)
Stripe 0:
Device Start Block Dbase State Reloc Hot Spare
c2t1d0s3 0 No Okay Yes
d31: Mirror
Submirror 0: d11
State: Needs maintenance
Submirror 1: d21
State: Okay
Pass: 1
Read option: roundrobin (default)
Write option: parallel (default)
Size: 24585216 blocks (11 GB)
d11: Submirror of d31
State: Needs maintenance
Invoke: metareplace d31 c2t0d0s1 <new device>
Size: 24585216 blocks (11 GB)
Stripe 0:
Device Start Block Dbase State Reloc Hot Spare
c2t0d0s1 0 No Maintenance Yes
d21: Submirror of d31
State: Okay
Size: 24585216 blocks (11 GB)
Stripe 0:
Device Start Block Dbase State Reloc Hot Spare
c2t1d0s1 0 No Okay Yes
d30: Mirror
Submirror 0: d10
State: Needs maintenance
Submirror 1: d20
State: Okay
Pass: 1
Read option: roundrobin (default)
Write option: parallel (default)
Size: 24585216 blocks (11 GB)
d10: Submirror of d30
State: Needs maintenance
Invoke: metareplace d30 c2t0d0s0 <new device>
Size: 24585216 blocks (11 GB)
Stripe 0:
Device Start Block Dbase State Reloc Hot Spare
c2t0d0s0 0 No Maintenance Yes
d20: Submirror of d30
State: Okay
Size: 24585216 blocks (11 GB)
Stripe 0:
Device Start Block Dbase State Reloc Hot Spare
c2t1d0s0 0 No Okay Yes
d35: Mirror
Submirror 0: d15
State: Needs maintenance
Submirror 1: d25
State: Okay
Pass: 1
Read option: roundrobin (default)
Write option: parallel (default)
Size: 24585216 blocks (11 GB)
d15: Submirror of d35
State: Needs maintenance
Invoke: metareplace d35 c2t0d0s5 <new device>
Size: 24585216 blocks (11 GB)
Stripe 0:
Device Start Block Dbase State Reloc Hot Spare
c2t0d0s5 0 No Maintenance Yes
d25: Submirror of d35
State: Okay
Size: 24585216 blocks (11 GB)
Stripe 0:
Device Start Block Dbase State Reloc Hot Spare
c2t1d0s5 0 No Okay Yes
d36: Mirror
Submirror 0: d16
State: Needs maintenance
Submirror 1: d26
State: Okay
Pass: 1
Read option: roundrobin (default)
Write option: parallel (default)
Size: 65553792 blocks (31 GB)
d16: Submirror of d36
State: Needs maintenance
Invoke: metareplace d36 c2t0d0s6 <new device>
Size: 65553792 blocks (31 GB)
Stripe 0:
Device Start Block Dbase State Reloc Hot Spare
c2t0d0s6 0 No Maintenance Yes
d26: Submirror of d36
State: Okay
Size: 65553792 blocks (31 GB)
Stripe 0:
Device Start Block Dbase State Reloc Hot Spare
c2t1d0s6 0 No Okay Yes
hsp001: is empty
Device Relocation Information:
Device Reloc Device ID
c2t1d0 Yes id1,ssd@n500000e01495a300
c2t0d0 Yes id1,ssd@n500000e01495b9b0High level instructions:
Use 'metadb -d' to delete any replicas on the failed disk.
If all the metadevices on the disk have already failed, remove disk.
Replace disk.
Partition disk.
Use 'metadb -a' to add replicas to new disk.
Use 'metareplace' (as shown in metastat output) to replace each of the failed metadevices (You don't actually have to list the new storage. It'll try the old name by default).
Everything should be green after that.
http://www.brandonhutchinson.com/Replacing_a_failed_disk_with_DiskSuite.html
Darren -
BEA-382513: OSB Replace action failed: bad value for type element anyType
Hello, in OSB I get this strange error message on my XQUERY TRANSFORMATION.
*<faultstring>BEA-382513: OSB Replace action failed updating variable "response":*
com.bea.wli.common.xquery.XQueryException:
*Error parsing XML: {err}XP0006: "*
*element {http://xmlns.oracle.com/pcbpel/adapter/db/top/CS2AdapterSelectOffenePosten_v0_5}Cs2DebitorOpVieCollection*
*{ {http://www.w3.org/2004/07/xpath-datatypes}untypedAny }":*
bad value for type element
*{http://xmlns.oracle.com/pcbpel/adapter/db/top/CS2AdapterSelectOffenePosten_v0_5}cs2RechungungenResponse*
*{ {http://www.w3.org/2001/XMLSchema}anyType }*
*</faultstring>*
I'm a pl/sql developer and I have no idea what this error message is telling me.
In this forum I'v read someting about a wrong namespace declaration. I can't see any wrong value on my xml (ok, I'm not the specialist here...)
Maybe someone of you xquey cracks might have a look at my code?
This is what I have:
_1.) a XQuery variable called cs2RechnungenResponse with this content:_
<cs2:Cs2DebitorOpVieCollection
xmlns:xsi="http://www.w3.org/2001/XMLSchema-instance"
xmlns:soap-env="http://schemas.xmlsoap.org/soap/envelope/"
xmlns:cs2="http://xmlns.oracle.com/pcbpel/adapter/db/top/CS2AdapterSelectOffenePosten_v0_5">
<cs2:Cs2DebitorOpVie>
<cs2:f40Konto>333</cs2:f40Konto>
<cs2:AMT_BEZEICHNUNG>Amt für Gesundheit</cs2:AMT_BEZEICHNUNG>
<cs2:f40Belnr>555</cs2:f40Belnr>
<cs2:f40Sohab>S</cs2:f40Sohab>
<cs2:f40Dmbet>100</cs2:f40Dmbet>
<cs2:f40Fadat>2011-05-05T00:00:00.000+02:00</cs2:f40Fadat>
<cs2:f40Valut>2011-05-05T00:00:00.000+02:00</cs2:f40Valut>
<cs2:f40Mahns/>
<cs2:f40F40Sj>0</cs2:f40F40Sj>
</cs2:Cs2DebitorOpVie>
</cs2:Cs2DebitorOpVieCollection>
_2. a xquery with this code:_
(:: pragma bea:global-element-parameter parameter="$cs2RechnungenResponse" element="ns2:cs2RechnungenResponse" location="../adapters/cs2_adapters/xsd/CS2AdapterSelectOffenePosten_v0_5_table.xsd" ::)
(:: pragma bea:global-element-return element="ns0:getDebitorRechnungResponse" location="../../interfaces/RechnungServiceTypes_v0_6.xsd" ::)
declare namespace ns3 = "http://www.llv.li/common/types/v1";
declare namespace ns2 = "http://xmlns.oracle.com/pcbpel/adapter/db/top/CS2AdapterSelectOffenePosten_v0_5";
declare namespace ns1 = "http://www.llv.li/fin/types/v1";
declare namespace ns0 = "http://www.llv.li/fin/services/rechnungService/v1";
declare namespace xf = "http://tempuri.org/fin_sb/RechnungsService/transformations/CARI_CS_2DBAdpter_to_RechnungsServiceGetOffenePosten_v0_5/";
declare function xf:CARI_CS_2DBAdpter_to_RechnungsServiceGetOffenePosten_v1_0($cs2RechnungenResponse as element(ns2:cs2RechnungenResponse))
as element(ns0:getDebitorRechnungenResponse) {
<ns0:getDebitorRechnungenResponse schemaVersion="0.6">
if ($cs2RechnungenResponse/ns2:Cs2DebitorOpVie) then
<ns0:debitorRechnungList>
for $Cs2DebitorOpVie in $cs2RechnungenResponse/ns2:Cs2DebitorOpVie
return
<ns0:debitorRechnung>
<ns1:peid>0</ns1:peid>
<ns1:rechnungsnummer>{ data($Cs2DebitorOpVie/ns2:f40Belnr) }</ns1:rechnungsnummer>
<ns1:rechnungsdatum>{ xs:date(fn-bea:remove-timezone-from-dateTime(data($Cs2DebitorOpVie/ns2:f40Fadat))) }</ns1:rechnungsdatum>
<ns1:faelligAm>{ xs:date(fn-bea:remove-timezone-from-dateTime(data($Cs2DebitorOpVie/ns2:f40Valut))) }</ns1:faelligAm>
<ns1:behoerde>{ data($Cs2DebitorOpVie/ns2:AMT_BEZEICHNUNG) }</ns1:behoerde>
<ns1:positionList>
<ns1:position>
<ns1:positionsnummer>1</ns1:positionsnummer>
<ns1:betrag>{ data($Cs2DebitorOpVie/ns2:f40Dmbet) }</ns1:betrag>
<ns1:waehrung>
<ns1:isoCode>CHF</ns1:isoCode>
<ns1:bezeichnung>Schweizer Franken</ns1:bezeichnung>
</ns1:waehrung>
</ns1:position>
</ns1:positionList>
<ns1:status>offen</ns1:status>
if ($Cs2DebitorOpVie/ns2:f40Mahns/text() > "") then
<ns1:mahnstufe>{ xs:int(data($Cs2DebitorOpVie/ns2:f40Mahns)) }</ns1:mahnstufe>
else ()
</ns0:debitorRechnung>
</ns0:debitorRechnungList>
else ()
<ns0:resultatStatus>
<ns3:code>Erfolgreich</ns3:code>
<ns3:beschreibung>Rechnungen aus MFK fehlen</ns3:beschreibung>
</ns0:resultatStatus>
</ns0:getDebitorRechnungenResponse>
declare variable $cs2RechnungenResponse as element(ns2:cs2RechnungenResponse) external;
xf:CARI_CS_2DBAdpter_to_RechnungsServiceGetOffenePosten_v1_0($cs2RechnungenResponse)
_3. this should result in this response, but it doesn't_
<soapenv:Envelope xmlns:soapenv="http://schemas.xmlsoap.org/soap/envelope/">
<soap-env:Body xmlns:soap-env="http://schemas.xmlsoap.org/soap/envelope/">
<v1:getDebitorRechnungenResponse schemaVersion="0.6" xmlns:v1="http://www.llv.li/fin/services/rechnungService/v1">
<v1:debitorRechnungList>
<v1:debitorRechnung>
<v11:peid xmlns:v11="http://www.llv.li/fin/types/v1">333</v11:peid>
<v11:rechnungsnummer xmlns:v11="http://www.llv.li/fin/types/v1">555</v11:rechnungsnummer>
<v11:rechnungsdatum xmlns:v11="http://www.llv.li/fin/types/v1">2011-05-05</v11:rechnungsdatum>
<v11:faelligAm xmlns:v11="http://www.llv.li/fin/types/v1">2011-05-05</v11:faelligAm>
<v11:behoerde xmlns:v11="http://www.llv.li/fin/types/v1">Amt für Gesundheit</v11:behoerde>
<v11:positionList xmlns:v11="http://www.llv.li/fin/types/v1">
<v11:position>
<v11:positionsnummer>1</v11:positionsnummer>
<v11:betrag>100</v11:betrag>
<v11:waehrung>
<v11:isoCode>CHF</v11:isoCode>
<v11:bezeichnung>Schweizer Franken</v11:bezeichnung>
</v11:waehrung>
</v11:position>
</v11:positionList>
<v11:status xmlns:v11="http://www.llv.li/fin/types/v1">offen</v11:status>
</v1:debitorRechnung>
</v1:debitorRechnungList>
<v1:resultatStatus>
<v11:code xmlns:v11="http://www.llv.li/common/types/v1">Erfolgreich</v11:code>
<v11:beschreibung xmlns:v11="http://www.llv.li/common/types/v1">Rechnungen aus MFK fehlen</v11:beschreibung>
</v1:resultatStatus>
</v1:getDebitorRechnungenResponse>
</soap-env:Body>
</soapenv:Envelope>
But I do not get this expectet result, all I get is the BEA-382513: OSB Replace action failed: bad value for type element anyType?
Any help would be appreciated.
Thanks
Best regards
rkcs2RechungungenResponse or cs2RechnungenResponse ? the error message says cs2RechungungenResponse, but the actual element is cs2RechnungenResponse (one less "u")
-
After replacing a failed hard drive with new one I inadvertently created a different account name(home/user) than the one in the Time Machine backup. Now I cannot restore the photos in iPhoto. What are my options?
The best thing to do would be to start over. Use Setup Assistant this time.
Boot into Recovery, launch Disk Utility, and erase the startup volume. This operation will destroy all data on the volume. Quit Disk Utility and install OS X. If your Mac was upgraded from an older version of OS X, you’ll need the Apple ID and password you used to upgrade, so make a note of those before you begin.
When you reboot, you'll be prompted to go through the initial setup process. That’s when you transfer the data from one of your backups. For a walkthrough, see here:
Using Setup Assistant
Don't transfer the Guest account, if it was enabled on the old system.
Note: You need an always-on Ethernet or Wi-Fi connection to the Internet to use Recovery. It won’t work with USB or PPPoE modems, or with proxy servers, or with networks that require a certificate for authentication. -
Root.sh fails on 2nd node
AIX 6
Oracle grid infrastructure 11.2.0.3
At the end of the grid install, ran the root.sh on the first node then on the second node, but failed on the second node. Ran deconfig was successfull, but root.sh failed again :
The deconfig worked but not the root.sh:
Successfully deconfigured Oracle clusterware stack on this node
mtnx213:/oracle/app/grid/product/11.2.0/grid/crs/install#/oracle/app/grid/product/11.2.0/grid/root.sh
Performing root user operation for Oracle 11g
The following environment variables are set as:
ORACLE_OWNER= oragrid
ORACLE_HOME= /oracle/app/grid/product/11.2.0/grid
Enter the full pathname of the local bin directory: [/usr/local/bin]:
The contents of "dbhome" have not changed. No need to overwrite.
The contents of "oraenv" have not changed. No need to overwrite.
The contents of "coraenv" have not changed. No need to overwrite.
Entries will be added to the /etc/oratab file as needed by
Database Configuration Assistant when a database is created
Finished running generic part of root script.
Now product-specific root actions will be performed.
Using configuration parameter file: /oracle/app/grid/product/11.2.0/grid/crs/install/crsconfig_params
User ignored Prerequisites during installation
User oragrid has the required capabilities to run CSSD in realtime mode
OLR initialization - successful
Adding Clusterware entries to inittab
USM driver install actions failed
/oracle/app/grid/product/11.2.0/grid/perl/bin/perl -I/oracle/app/grid/product/11.2.0/grid/perl/lib -I/oracle/app/grid/product/11.2.0/grid/crs/install /oracle/app/grid/product/11.2.0/grid/crs/install/rootcrs.pl execution failedMy answer you can find here (in your duplicate post): root.sh fails on 2nd node Timed out waiting for the CRS stack to start
Maybe you are looking for
-
IPod/iTunes issue with Fast User Switching
I have Fast User Switching enabled on my iMac Core 2 Duo running 10.4.8. My daughter usually leaves her iPod connected and it is causing problems when switching to another user. Other users get the message that the connected iPod is associated with a
-
Prompt for a username/password while accessing a resource in wls 6.0
Hi all, I want to restrict access to any resource on my weblogic server 6.0 and prompt for a user name and password before accessing any resource. I did this using weblogicurl.policy file in wls 5.1. I am not able to find out how to do this in 6.0. C
-
Character set supported by post and util.zip
hi friends in my application i was sending a file(in client) using post method and in server getting using servlets.i what that file to be compressed using util.zip in client and uncompresed in server but i was unsucessful .i think the file before po
-
Hi, I was hoping to add some functionality to my application to enable the user to open it in full screen mode to free up some real estate. Getting to full screen mode is working fine but I was a bit surprised to see that all keyboard interaction (ba
-
I was wondering, is there any possible way of getting the Compass app from the iPhone on to my iPod touch? I hoped to find it in the latest software update (3.1.1), though was disapointed to see it wasn't, and I can't find it on the App Store, so is