Replacing Hard Drive in MAC Pro

Sorry if this has been asked. I purchased a used MAC Pro from a friend that needed money. The hard drive is too small to accommodate all the software on my other MAC so Migration Assistant will not work. I know how to put secondary drives in and format them. How do I replace the primary drive with a larger one? I don't know how to install a clean hard drive on a MAC and start from scratch. I am also planning on adding more RAM but I do know how to do that. Thanks

Pretty simple on the Mac Pro. Just pull the tray with the primary drive out (there are no cables to worry about) and then also pull out one of the secondary trays. Put a new drive in one of the secondary trays, then slide it into the primary slot, and put the former primary drive into the vacant secondary slot.
Then you just install a fresh copy of OS X from the install DVD. Just put it in the drive and hold down "C" at boot. Then follow the instructions on screen, and Migration Assistant will pick up the second drive and do it's thing.
Finally, Mac is not an acronym so doesn't need to be in all caps. It's short for Macintosh... Like the apple you can buy in a grocery store.

Similar Messages

  • How to replace hard drive in macbook pro?

    How to replace hard drive in macbook pro?

    Hi S,
    If you have the newer unibody style, it's very easy. If it's one of the earlier models, it's considerably more difficult. Go to Apple Menu > About This Mac > More Info > Hardware and find your Model Identifier. Then go to ifixit.com, or powerbookmedic.com or macsales.com or youtube or others and there are illustrated, detailed directions. Good luck to you and post back if you have further questions.

  • Can I format an IDE Hard Drive from Mac Pro?

    I use a mid - 2012 Mac Pro; run Mavericks OS X 10.9.2.
    1. Can an IDE hard drive (using an external drive) be formatted to 10.9.2, from my Mac Pro using Mavericks? (the IDE hard drive is new/unformatted).
    2. Once formatted to 10.9.2, can I reformat the IDE hard drive to Mac OS X Leopard 10.5.8, from my Mac Pro using Mavericks?
    3. If so, would should I do to accomplish Question # 2 above?

    The version of the OS that is running  is not relevant to formatting the drive. When you format a drive in any OS, you should select "Mac OS extended journaled." (That is, unless you plan to share the drive with a Windows computer.) Formatted this way, the drive can be used with any version of Mac OS.
    You do not have to reformat the drive each time you connect it with a different OS.

  • I replaced hard drive in macbook pro and when turning on i get a blinking question mark

    just replaced hard drive on my '09 macbook pro and rebooted to get the blinking question mark.  what do i do? not sure i have the installation disk.  i had this happen once on an older macbook and was able to figure it out but i can't remember what i did.

    Schedule an appointment with a Genius the SSD is gone.

  • How to install hard drive into mac pro

    how to install hard drive into mac pro

    I recently bought a new 2TB internal sata drive for my Macpro.
    The installation was easy, but I'm not sure what to do next.
    For one, should I partition the drive?
    My purpose for buying the drive was to use it as my go to drive for Parallels. I used to run my music studio on Windows based machines, and my older project files require a windows OS to recover. I installed Parallels so I can have my studio running Mac and Windows programs which will enable me to access my old project files and take them into my newer Protools system.
    So now, I've installed my new hard drive, but I'm not sure if I should partition it....And!? I'm not sure how to designate that drive for my virtual pc on Parallels. I was able to allocate enough disk space to parallels in order to load my music software, but at this point, I'm not sure if I've just promised it disk space from my original partitioned drive (which only has about 350 GB left on it).
    I would love to be able to make one internal drive available for Parallels, and the other available for the rest of my OSX. When I use Parallels, I still would like to save some extra information on the 2TB drive as well from my dekstop running OSX.
    I hope this makes sense! Your help is much appreciated!

  • Installing CS6 on a replacement hard drive (same Mac Book Pro)

    I am running the latest version of CS 6 on an older (2008) 15" Mac Book Pro (OSX 10.8.2), when I'm away on assignment.  The original 200GB hard drive needs to be replaced and in preparation I've cloned the complete system onto an external hard drive.  I'll be replacing the original hard drive with a larger (1TB) version and can clone everything back onto the newly installed hard drive when it arrives.  But in the "test" I tried today, PS CS6 would not open.  How do I go about installing my legally obtained and paid for copy of CS6 onto the new hard drive?  Do I de activate the present version, then download a copy to the new hard drive and activate it that way or will that be seen as a third machine, since I have one copy on a desk top and once on the old hard drive in the Mac Book Pro.  I just don't want to loose a CS6 activation?
    TYhanks for any wisdom on this
    David

    Do I de activate the present version, then download a copy to the new hard drive and activate it that way
    Exactly. All Adobe programs must be properly installed for the licensing system to work. If you have trouble and get warnings, call support to reset activations.
    Mylenium

  • Replacing a 250G Hard drive on Mac Pro

    Does anyone have a good idea on how I can replace my modest 250G hard drive with a new 500G WD without having to reload all the software. In other words just mirror the drive to the new one?
    Thanks....
    MAC PRO 2.66 8G of RAM   Mac OS X (10.4.9)   FCP 5.1.4
    MAC PRO 2.66 7G of RAM   Mac OS X (10.4.9)   FCP 5.1.4

    With both drives installed. This is the simplest way:
    How to Clone Using Restore Option of Disk Utility
    1. Open Disk Utility from the Utilities folder.
    2. Select the backup or destination volume from the left side list.
    3. Click on the Erase tab in the DU main window. Set the format type to Mac OS Extended (journaled, if available) and click on the Erase button. This step can be skipped if the destination has already been freshly erased.
    4. Click on the Restore tab in the DU main window.
    5. Select the backup or destination volume from the left side list and drag it to the Destination entry field.
    6. Select the startup or source volume from the left side list and drag it to the Source entry field.
    7. Double-check you got it right, then click on the Restore button.
    For added precaution you can boot into safe mode before doing the clone.
    You will need to first prep the new drive before the above. Follow this procedure:
    Extended Hard Drive Preparation
    1. Open Disk Utility in the Utilities folder.
    2. After DU loads select your new hard drive (this is the entry with the mfgr.'s ID and size) from the left side list. Note the SMART status of the drive in DU's status area. If it does not say "Verified" then the drive is failing or has failed and will need replacing. Otherwise, click on the Partition tab in the DU main window.
    3. Set the number of partitions from the dropdown menu (use 1 partition unless you wish to make more.) Click on the Option button and be sure the selected partition scheme is set to GUID. Click on the OK button. Set the format type to Mac OS Extended (Journaled.) Click on the Partition button and wait until the volume(s) mount on the Desktop.
    4. Select the volume you just created (this is the sub-entry under the drive entry) from the left side list. Click on the Erase tab in the DU main window.
    5. Set the format type to Mac OS Extended (Journaled.) Click on the Options button, check the button for Zero Data and click on OK to return to the Erase window.
    6. Click on the Erase button. The format process will take 30 minutes to an hour or more depending upon the drive size.

  • Replaced hard drive in Mac book pro now what

    I just replaced the hard drive now what?

    Why did you replace it if you didn't know what to do?
    First, partition and format the drive for OS X.
    Then, Install OS X on the drive.
    Since you did not provide information on the Mac model you are using nor the version of OS X you plan to install, there's little more to tell you.

  • Suggestions on Replacement Hard Drive for Mac Book Pro

    I have a MBP - 15-inch, Late 2008 - the apple tech tells me its starting to get daaged- before it goes I want to replace it.
    She told me to go to Newegg and purchase one there...however not sure what to get...
    I want a 1TB drive if its possible....anybody got some qualified advice...
    Thanks.

    Almost any 2.5" SATA  hard drive can be used.  Recommend that you get a 7200 rpm drive, you will appreciate the increased performance over what you currently have.  Just be aware there are not many 1TB 2.5" drives around.  The only ones OWC carry at this point are Hitachi and Toshiba.  I wouldn't buy either brand.
    I just successfully installed a WD Scorpio Black (750GBm 7200 rpm) in my MBP.  Both physical installation & installation of OS X went without a hitch.  It's running like a charm.
    Also, you will need 1 tiny & 1 small phillips screwdriver and a small torx screwdriver to open your MBP and replace the drive.

  • New hard drive in Mac Pro showing 0 bytes after partitioning

    I bought a Western Digital Caviar 2TB internal hard drive for my Mac Pro (2 x 2.66 GHz Dual Core Intel Xeon (late 2006), 12GB RAM, Mac OS 10.6.8). It already has two 500GB internal drives in two of the four slots.
    I slotted the new WD hard drive in and started up the Mac, getting an alert saying there was an unrecognisable disk and did I want to initialise it? Yes, so it opened up Disk Utility.
    This showed my two 500GB drives plus the new WD drive at 2TB. To initialise it I erased the disk which failed with an error ("POSIX reports: The operation
    couldn't be completed. Input/output error").
    I next decided to use Partition instead, choosing just one partition of 2TB, Mac OS Extended (Journaled). After 7 minutes it said the process had been completed and the volume was mounted, though it didn't appear on my desktop, just in Disk Utility. I thought a restart would refresh and show it on the desktop.
    Once the Mac was up and running again there was nothing there at all - and now it wasn't even listed in Disk Utility. I shut down, took the hard drive out,
    looked at it, scratched my head, replaced it, and turned the Mac back on.
    Once again I got an alert telling me the disk was uninitialised and would I like to format it, so clicked OK and Disk Utility opened. This time the disk was
    there (WDC WD20EZRX-00DC0B0) but no volume. The info said the drive had a size of 0 Bytes and I could not erase or partition as all buttons were greyed out,
    with the Partition tab saying 'this disk is too small to contain partitions'.
    So what can I do now? According to macupgrades.co.uk this drive should work in my model of Mac (they recommend and sell it, though I purchased it from NORDPC via Amazon as it was a little cheaper).
    http://www.macupgrades.co.uk/store/product_info.php?products_id=532
    I tried, with the help of my more computer-literate brother, to erase the disk from the command line via the Terminal, getting a result of "Error: 6: POSIX
    reports: Device not configured". (Actually we first tried to reformat it, with an error of "does not appear to have a valid file system format").
    Does anyone with more knowledge of such things have any ideas or advice? It would be much appreciated.

    Unless the drive and sled are not inserted properly - unlikely - or that other drives don't work in that slot - watch out if true, unlikely but loose SATA cable - it IS a bad drive.
    If you don't have a PC, setup Windows VM and use WD Lifeguard which is excellent and tests for things like bad SATA cable communicating.
    You could also - I always use Partition tab btw - go in there and set it to exFAT and Windows Master Boot Record. All you want is a good drive. This one is not.
    GUID tests first and last 10,000 sectors or more to insure that the partition tables and hidden areas work (they are not it is failing). Use to be that a "backup volume information block" was treated as optional if any sectors failed, now it is not.

  • What is the prefered hard drive for Mac Pro 1.1?

    Hello everyone, I want to fill the 4th Mac Pro Raid hard drive. I want to know the best hard drive out there and the maximum capacity I should buy. The computer came with 3 hard drives 750.16 each. Thank you for help!
    Mac OS X/10.6.8/2x3 GHz dual-core Intel Xeon/13 GB 667 MHz DDR2 FB-DIMM

    4TB if you want max size. There is no max and it all depends on what you do.
    Not sure but "pro raid" better not  be Apple RAID controller as that does have limits and problems and not  sure you  use and need RAID5 controller.
    I'd say WD 10K 1TB VelociRaptor as "best in class" outside of SAS
    WD Black 2TB for cost size performance or 4TB new $300 for max
    WD Black line has been used by users and Apple for OEM and 1TB model
    When doing RAID or RAID5 I would use the old drives for backup and replace all four.
    And keep the boost drive on SSD ($100 Samsung 840, or 10K WD VR 250GB)  or 500GB WD VR $139, great little and fast.  Samsung 840 240GB is also gotten affordable-ish. Nice larger boot drive.
    I went with 8x2GB for $130 now from Amazon for FBDIMMs.
    And ATI 5770.

  • Swap Hard Drives Between Mac Pro's

    I have a MacBook Pro "Core 2 Duo" 2.53 15" (Unibody - Late 2008) that has been upgraded from the standard 320 GB SATA hard drive, to a Seagate 750 GB SATA 16 MB cache 7200 rpm hard drive.
    I have recently upgraded to a MacBook Pro "Core 2 Duo" 2.66 15" (SD - Mid 2009) that has the standard 320 GB SATA hard drive.
    Both are running Mac OS X Snow Leopard 10.6.8.
    I will be selling my older (2.53GHz) Mac Pro but would like to keep my larger hard drive.
    Question
    Can I simply swap the hard drive out of my older (2.53GHz) Mac Pro and install it into the newer (2.66GHz) Mac Pro, without having to reinstall the Mac OS X software?
    I no longer have any of my OS X install disks.
    Will the 750 GB hard drive still perform the same in the newer Mac Pro, given that they are running the same OS?
    Thanks in advance!

    From what I understand the USB/PCIe interfaces are (somewhat) device specific. But it depends on the particular vendor in question.
    According to barefeats.com, regarding USB devices:
    "...Our only concern was that it {the CalDigit adapter} only worked with CalDigit USB 3.0 enclosures like the AV Drive. They since updated the driver to "unlock it." In fact, all the USB 3.0 results posted above for non-Cadigit enclosures were done with the CalDigit PCIe USB 3.0 host adapter...."
    So, for example, the Lacie PCIe adapters are "specific". Only works with their stuff. Originally the CalDigit PCIe adapter was the same: limited to use with their devices only. But they've altered that so that it is more generic. In fact, it was used to test the other USB 3.0 devices in the barefeats tests.
    So the CalDigit card, at least, is a more flexible choice.

  • How do I get LR4 to find all photos in catalog after replacing hard drive on mac? question marks all

    I had the hard drive replaced on my mac.  I did a restore from back up drive to my new hard drive.  First LR4 couldn't find the catalog so I pointed to it. Then I opened lightroom 4 and it cannot see ANY of my photos. I don't want to link each folder full of photos it will take hours. Isn't there another way to do this so it finds them all at once?  Photos are still located in the same location on the new hard drive after restore.  Nothing changed except the hard drive.  Thank you!

    I did find something in another post that suggests to go to the top most file in the structure and right click and click on "find missing folder" then you point to that folder and it will find all subfolders and photos.   This really worked well for most of the photos but I have I must have moved at some point that I will have to relocate.  This is good information whether you are working with a Mac or a PC. I think it would work for either.  I hope this helps someone else out there.

  • Maximum Size of Hard Drive in Mac Pro (Early 2008)

    What is the Maximum size of Hard Drive that I can install in drive bay 3 or 4?
    Computer info below:
    Model Name: Mac Pro (Early 2008)
    Model Identifier: MacPro3,1
    Processor Name: Quad-Core Intel Xeon
    Processor Speed: 2.8 GHz
    Number Of Processors: 2
    Total Number Of Cores: 8
    L2 Cache (per processor): 12 MB
    Memory: 14 GB
    Bus Speed: 1.6 GHz
    Boot ROM Version: MP31.006C.B05
    SMC Version (system): 1.25f4
    Hardware UUID: FF121465-84A1-52F2-A94A-58A60A20F4AF

    WE don't know, all there are today are 2TB and those are fine. I think you could RAID 6 for 10TB and maybe then?
    Serious, there are none. Do you really expect to hit some ceiling?
    http://forums.xlr8yourmac.com/drivedb/search.drivedb.lasso

  • Going into my hard drive causes mac pro to lock up like fort knox

    Hi, I have been a mac user for just a hair over a year.(Apple will not help me with anything)
    All has been swell until now.
    If I go into my hard drive my computer locks right up. I can do
    nothing to move it along. The only option I have is to hold down the
    power button for six seconds, which kills me and the computer a little
    each time. I booted up the computer using the mac install disc and I
    used disk utility to "repair" the disk. It reported the disk was "OK".
    I thought swell, and went into documents on the hard disk and it
    locked my computer up again. I let it sit there for an hour and
    nothing moved. apple/option/esc does not do anything. I went into time machine and
    went to the documents there and it locked up the computer too. I went into finder and went to documents and it locked up the computer. I went into other areas of the hard drive and it locked up the computer. The funny thing is I can go on the internet, use programs, read email, and everything works fine. Can anyone guide me in
    the right direction in solving this problem I am facing?
    Specs:
    Model Name: Mac Pro
    Model Identifier: MacPro2,1
    Processor Name: Quad-Core Intel Xeon
    Processor Speed: 3 GHz
    Number Of Processors: 2
    Total Number Of Cores: 8
    L2 Cache (per processor): 8 MB
    Memory: 8 GB
    Bus Speed: 1.33 GHz
    Boot ROM Version: MP21.007F.B06
    SMC Version: 1.15f3
    troubled drive:
    ST3750640AS P:
    Capacity: 698.64 GB
    Model: ST3750640AS P
    Revision: 3.BTH
    Serial Number: 5QD1P*
    Native Command Queuing: Yes
    Queue Depth: 32
    Removable Media: No
    Detachable Drive: No
    BSD Name: disk0
    Bay Name: "Bay 1"
    Mac OS 9 Drivers: No
    Partition Map Type: GPT (GUID Partition Table)
    S.M.A.R.T. status: Verified
    Volumes:
    Macintosh HD:
    Capacity: 698.32 GB
    Available: 328.75 GB
    Writable: Yes
    File System: Journaled HFS+
    BSD Name: disk0s2
    Mount Point: /
    second drive:
    SAMSUNG HD753LJ:
    Capacity: 698.64 GB
    Model: SAMSUNG HD753LJ
    Revision: 1AA01112
    Serial Number: S13UJ1CQ6***
    Native Command Queuing: Yes
    Queue Depth: 32
    Removable Media: No
    Detachable Drive: No
    BSD Name: disk1
    Bay Name: "Bay 2"
    Mac OS 9 Drivers: No
    Partition Map Type: GPT (GUID Partition Table)
    S.M.A.R.T. status: Verified
    Volumes:
    Boot OSX:
    Capacity: 128 MB
    Writable: Yes
    File System: HFS+
    BSD Name: disk1s3
    Mount Point:
    <Edited by Moderator>

    Sounds like itneeds some good basic maintenance and troubleshooting. Stop using this drive. Start trashing temp files, and off loading good files.
    Everytime you freeze and do a hard restart, the chance that the journal, directory, file system and data are compromised increases, in spite of the "OKAY" from Disk Utility's repair routines it is not reliable. And leads to false sense of security. Disk Utility only checks the basic directory, not the files themselves.
    It may be something like a damaged Finder plist/preference, or worse, but either you look for an easy fix, or just start cleaning up and moving files and system to a good drive and system.
    You may have bad blocks on your drive causing all this. Or not. TechTool can detect bad sectors, but not map them out. (Deluxe is part of AppleCare; or Pro, commercial version).
    Start using SuperDuper if you don't already, and Disk Warrior, premiere for disk repairs.
    http://www.shirt-pocket.com/SuperDuper/SuperDuperDescription.html
    What you need to be doing is rebuild your system from the foundation up.
    You may need to check out Data Rescue II demo from Prosoft Engineering to recover files.
    I would begin by installing OS X on another drive, or restoring from TimeMachine. Create/name an "emergency" boot drive partition. Doesn't need to be that large. Keep it handy just for doing repairs and maintenance. Keep another as a clone of your working system and backup - in addition to TimeMachine.
    You may want to start by erasing the drive (not just the OS volume) with a 7-way write (not just zero all, it does NOT do a reliable safe job mapping out bad blocks) and restore from TimeMachine. Or work with a new drive.

Maybe you are looking for