Reply to email does not add previous address

A week or so into iOS7 upgrade, all of a sudden when click to reply to person, it jumps to body of email, without adding in prior person's address in the "TO". It shows a blue arrow, but nothing else! Why do I have to re-type in person's address?

Also, it doesn't happen all the time. It seems this person has a gmail address. I tried sending myself an email from my other gmail address and replying to, but it puts my gmail address in the REPLY. Weird.

Similar Messages

I am having trouble sending email. I get reply that server does not allow relaying. iphone 4

I am having trouble sending email. I get reply that server does not allow relaying. iphone 4

having the same problem with iphone 4S. help! it's only happening from one email acct. gmail is fine.

DHCP server does not assign IP addresses SG500 firmware 1.3.5

good day collegues
has any of you come across the following issue:
my switch (after upgrading to the newest firmware 1.3.5) does not assign IP addresses to some of the hosts.
after a couple of hours I managed (do not even how) to force my switch to assign IP addresses only to some of the hosts.
still some of them cannot get the IP address and remain with "funny" IP address like i.e. 169.254.100.100
additional info
1. if I boot my switch with the previous version of firmware (1.3.0.6) everything is OK. all my hosts get correct IP addresess
2. the hosts which do not get IP address were perviously entered in stat host table - now removed, ARP cleared, etc, everything many many times rebooted.
I ran out of ideas, could you pleae give me some hints ?
the config below:
config-file-header
SG500
v1.3.5.58 / R750_NIK_1_35_647_358
CLI v1.0
set system mode router queues-mode 4
file SSD indicator encrypted
ssd-control-start
ssd config
ssd file passphrase control unrestricted
no ssd file integrity control
ssd-control-end zzz
no spanning-tree
vlan database
vlan 11,13-14
exit
voice vlan oui-table add 0001e3 Siemens_AG_phone________
voice vlan oui-table add 00036b Cisco_phone_____________
voice vlan oui-table add 00096e Avaya___________________
voice vlan oui-table add 000fe2 H3C_Aolynk______________
voice vlan oui-table add 0060b9 Philips_and_NEC_AG_phone
voice vlan oui-table add 00d01e Pingtel_phone___________
voice vlan oui-table add 00e075 Polycom/Veritel_phone___
voice vlan oui-table add 00e0bb 3Com_phone______________
no ip dhcp snooping verify
ip dhcp snooping information option allowed-untrusted
ip dhcp snooping vlan 11
ip dhcp snooping vlan 13
ip dhcp snooping vlan 14
ip arp inspection logging interval infinite
green-ethernet energy-detect
no eee enable
arp timeout 1
ip dhcp server
ip dhcp pool host q409
address 10.10.11.2 255.255.255.0 client-identifier 01:00:08:9b:ac:8f:92
default-router 10.10.11.254
dns-server 10.10.10.1
exit
ip dhcp pool host PCH-100
address 10.10.11.10 255.255.255.0 client-identifier 01:00:06:dc:41:ef:ef
default-router 10.10.11.254
dns-server 10.10.10.1
exit
ip dhcp pool host q209
address 10.10.13.3 255.255.255.0 client-identifier 01:00:08:9b:ac:72:ba
client-name q209
default-router 10.10.13.254
dns-server 8.8.8.8
exit
exit
ip dhcp pool network HOME
address low 10.10.11.1 high 10.10.11.254 255.255.255.0
lease infinite
default-router 10.10.11.254
dns-server 10.10.10.1
exit
ip dhcp pool network GUESTS
address low 10.10.14.1 high 10.10.14.254 255.255.255.0
lease infinite
netbios-node-type b-node
default-router 10.10.14.254
dns-server 10.10.10.1 62.233.233.233
exit
ip dhcp relay address 10.10.10.1
ip dhcp relay address 10.10.11.254
ip dhcp relay address 10.10.13.254
ip dhcp relay address 10.10.14.254
no boot host auto-config
no qos
qos advanced-mode trust dscp
qos wrr-queue wrtd
exit
hostname SG500
line telnet
exec-timeout 0
exit
logging buffered debugging
no logging file
aaa authentication login Telnet local
aaa authentication enable Telnet enable
aaa authentication dot1x default none
line telnet
login authentication Telnet
enable authentication Telnet
password 999 encrypted
exit
no passwords complexity enable
passwords aging 0
username 999 password encrypted 999 privilege 15
ip http timeout-policy 0 http-only
clock timezone " " 1
clock summer-time web recurring eu
clock source sntp
clock source browser
sntp unicast client enable
clock dhcp timezone
ip domain name 999
ip name-server 10.10.10.1 62.233.233.233 8.8.8.8
ip host 999 10.10.13.3
ip telnet server
no service mirror-configuration
no security-suite deny syn-fin
security-suite syn protection mode disabled
interface vlan 1
ip address 10.10.10.254 255.255.255.0
no ip address dhcp
interface vlan 11
name HOME
ip address 10.10.11.254 255.255.255.0
ip dhcp relay enable
interface vlan 13
name DMZ
ip address 10.10.13.254 255.255.255.0
ip dhcp relay enable
interface vlan 14
name GUESTS
ip address 10.10.14.254 255.255.255.0
ip dhcp relay enable
interface gigabitethernet1/10
description "(99) QNAP 409"
switchport trunk native vlan 11
exit
macro auto disabled
macro auto processing type host enabled
macro auto processing type ip_phone disabled
macro auto processing type ip_phone_desktop disabled
macro auto processing type router enabled
mac address-table aging-time 10
ip default-gateway 10.10.10.1
snmp-server set 999 permit

Hi Andbor, please make a backup config of your file, factory reset the switch.
After this, manually configure a DHCP scope without any other configuration.
Just something simple like this
ip dhcp pool network GUESTS
address low 10.10.14.1 high 10.10.14.254 255.255.255.0
lease infinite
netbios-node-type b-node
default-router 10.10.14.254
dns-server 10.10.10.1 62.233.233.233
Verify your machine receive IP address with no other configuration.
In some ways, I'm afraid some of your connections black listed due to the arp inspection.
-Tom
Please mark answered for helpful posts

Using JDIC opens Outlook But When I click on send email email does not send

Hi to every one plz help me.
I have used JDIC and when i open outlook through Desktop.mail(message);
outlook express gets open but when i click on send email then email does not get send undelivered message comes even though i have tried to send the email on the same address by manually opening outlook with coding then there is no problem for sending email.
here is the error come in inbox after pressing send button.
Your message did not reach some or all of the intended recipients.
      Subject:     COSMOS
      Sent:     9/15/2008 2:12 PM
The following recipient(s) could not be reached:
      '[email protected]' on 9/15/2008 2:12 PM
            None of your e-mail accounts could send to this recipient.Thanks
ABid

by using SMTP before email address problem solved
SMTP:[email protected]
but is there any other way to solve this problem please reply me thanks.

My iCloud email does not work. Getting error message that i need to uncheck SSL . This does not work. Help

icloud Email does not work. When running Connection doctor it indicates I must check or uncheck SSL. This has not fixed the problem

iCloud email addresses (@mac.com, @me.com and @icloud.com) require SSL. Is your address an iCloud address or someone else?

When I forgot my password, my husband received the instructions at his email. His email does not appear any where in my account. How do I solve this problem?

When I forgot my password, my husband received the instructions at his email. His email does not appear any where in my account. How do I solve this problem?

When you set up your ipad did you or your husband also set up a rescue e-mail address for you? If so, that would be why he received the instructions. Or do you sync your ipad with his computer?
Actually in terms of it being a problem, it actually makes it easier for you to answer your security questions and follow the instuctions to get back on your ipad. Otherwise, you'll have to call Apple Support.
To delete the rescue e-mail account pleases read this thread. (Poster's photos did not come through with the instructions.)
https://discussions.apple.com/thread/5218141?start=0&tstart=0

4.0 webservice does not work when Address Cleanse is used

Hello,
For my real time web service, I am unable to add any address cleansing transforms and make it work. The web service works fine as long as I do not add any address cleanse transform.
As soon as I add any address cleanse transform and try to start the service, the real time services list icon would turn yellow for more than 10 mins with the status stuck as "Service Starting"
The code in designer complies fine. The address cleanse transform works fine with batch jobs. Web services without address cleanse transforms work fine. Am not sure what the problem might be.
It'd be great if you could give some pointers on how to resolve it.
Thanks for looking.
Regards
T.

Hi Vidya,
Thanks for posting your example. You may want to remove your workspace details from the previous posting, or at least update the password on the workspace. I've taken a look at your example and initially couldn't see anything wrong with your tree query. However, when I ran your query in SQL Workshop, it only returned one row, which would explain why you were only seeing one node in your tree! I've updated your query to use a WITH clause, and the tree is now working correctly. I believe you've hit an underlying database bug where the CONNECT BY query is only returning 1 row, when in fact it should return > 1 row. By re-writing the query to use a WITH clause, you can get around the problem.
Regards,
Hilary

5Th Gen AE Does Not Assign IP Address in Bridge Mode

I have three AEs in my house...two of which are 4th gen and one is 5th gen, and two of which are set up as bridge (a 4th gen and a 5th gen). The 5th gen does not generate ip addresses reliably...everytime I go to the room where the 5th gen AE is I have to turn off the wifi on my device and turn it back on to get an ip address. This happens 100% of the time. I have tried my MBP, as well as my iPhones (4s and 5.) I also noticed the ip address that is being assigned for the bridges is of totally different denimination. The 4th gen bridge gets an ip of 10.0.1.4 where as the 5th gen gets a 192.168.1.76...the DHCP address range for the main is 10.0.1.2 through 100 and it should be assigned one of those ips. I'm kinda suspecting this is why the bridge is not working properly. I just don't understand why this unit is acting this way. Any input to help solve this mystery will be greatly appreciated. CHEERS:-)

Did resetting to factory help this issue? I'm having the same problem with my 5th and 3rd gen AE's. I've added a new router (pfSense) and only need the AE's for access points. The following is the result on some problem tracking:
Working on my network ip addressing issue. I shut everything down. I brought up my internal wired network of pfSense router, internal switches, appleTv units, printers and a couple of computers. All Addresses were correctly assigned. I released/renewed the ip addresses to check if the address assigned would remain correct, and this test passed.
I then connected my cable modem to the internet, which connected with no problem. I then again tested release/renew of addresses, and this test pasted with no problems. And I had internet access.
My internal network follows the 10.0.1.xxx address range. I leave 20-99 open as my dynamic range, and assign my AppleTv, DirecTv, SlingBox, and MacMini server to static addresses via MAC reservation. All these are functioning correctly.
Final test. I add my Airport Extreme 5th gen, which is in bridge mode, with no guest network, and the light turns green. I open up my MacBook, connect via WiFi, and the address is 192.168.100.34, not correct. I turn WiFi on my MacBook off, then I turn it on, after three cycles I get a correct ip address.
I confirm via airport utility my settings. I see nothing to change. I replace my Airport Extreme 5th gen , with my older Airport Extreme 3rd gen, and I once again get a 192.168.100.22 address which is not correct. I cycle the WiFi setting in my MacBook and after a few cycles, I get a correct address.
My DHCP server is an older Dell system running the linux based software pfSense. I made this change after I started getting bad IP addresses from my Airport Extreme 5th gen. My cable modem is a Zoom 5431J DOCSIS 3.0. But my first test was verifying the assignment of addresses from pfSense, without the cable modem.
I've powered off both Airport Extremes and have checked the settings. Not sure what else I might try with these Extreme units.

I forgot my password and my birthday and email does not recognize. please help me, it happen when I buy my new iphone5s and change the Apple ID of my old iPhone 4.

i have a new iPhone 5s, it does not recognize my password, when I try to restore it my birthday and email does not recognize, it only happen when I change my old iPhone 4 and change the Apple ID of it. please help me, all my phone now does not recognize my password.

To change to iCloud ID on your phone you have to go to Settings>iCloud, tap Delete Account, provide the password for the old ID then sign in with the new ID. If you don't know the password for the old ID, and if the old ID is an earlier version of your current ID, go to https://appleid.apple.com, click Manage my Apple ID and sign in with your current iCloud ID. Click edit next to the primary email account, change it back to your old email address and save the change. Then edit the name of the account to change it back to your old email address. You can now use your current password to turn off Find My iPhone on your device, even though it prompts you for the password for your old account ID. Then go to Settings>iCloud, tap Delete Account and choose Delete from My iDevice when prompted (your iCloud data will still be in iCloud). Next, go back to https://appleid.apple.com and change your primary email address and iCloud ID name back to the way it was. Now you can go to Settings>iCloud and sign in with your current iCloud ID and password.

Express does not show IP address of wireless camera

I have a functioning Axis M1011 wireless camera, with a live stream into Safari on my local iMac. All is well.
My brand new Airport Express is definitely providing the wireless camera feed, as my internal airport card on my iMac is OFF.
What is odd is that Express does not show IP address of the wireless camera when you click on it in Airport Utility.
The iMac is static at 10.0.1.2. Express LAN IP is static at 10.0.1.1. The camera's wireless IP is static at 10.0.1.3.
I have a working, hidden network created by express.
I am baffled why express does not "report" the IP address of the camera that it definitely sees.
It does not report any wireless clients at all.
Any ideas?
Thanks.
mac

So your ASA should have a route on the inside interface to internal networks. The address of that next hop in the routing table is the one you should have in your arp table allowing you to reach non-directly-connected (subnet-wise) hosts within the scope of that route statement.
Think through the logic - ASA pings a host. It needs to determine proper egress interface. It checks and asks "Is it reachable via a directly connected interface (most preferred route)?" Answer no. "Do I have a route statement telling me how to get to it?" Answer yes (otherwise use default). OK - so ASA sends packet out egress interface defined in that route statement to the next hop as defined in route statement and waits for reply.

My Email does not have any functions on the bottom bar?

My Email does not have any functions on the bottom bar?
I open an email and there no functions to delete forward or reply with. Anyone have an idea?

Hi
Just to clarify what your saying under menu > settings > Connectivity the only option you can see is Bluetooth? There are no other options to select?
Because under the connectivity menu you should be able to Network, WiFi, Bluetooth, USB, Settings, Connection manager, Mobile data tracker, Data Transfer, Video sharing, Admin settings and play via radio.
All the options should be visible on the connectivity menu on a N8 with Nokia Belle installed.
If you find this post helpful, a click upon the white star at bottom would always be appreciated.
If it also solves your problem, clicking ACCEPT AS SOLUTION below it will benefit other users!

I want to email a Pages document as a Word doc. I used to be able to do this by clicking on share then send via mail then on Word and an email would appear with my word doc attached. Now the email does not come up. Why?

I want to email a Pages document as a Word doc. I used to be able to do this by clicking on 'share' then 'send via mail' then on 'Word' and an email would appear with my word doc attached. Now the email does not come up. Why?

It's difficult to do more than guess when you don't say what version of OS X or Pages you're running, but if you're on the latest, have you tried the Share menu -> Send via Mail command?
If that doesn't help, you may have better luck if you ask in the Pages forum:
Pages
When you repost, be sure to include full details about your versions so that people know what it is you're working with.
Regards.

Hello everybody,i've forgot my apple password and i wanted to reset it to a new one but i also forgot the security question and the alternative email does not work and i am really need to log in to my apple i d because my iPhone 4g won't let me access it

Hello everybody,i've forgot my apple password and i wanted to reset it to a new one but i also forgot the security question and the alternative email does not work and i am really need to log in to my apple i d because my iPhone 4g won't let me access it so anyone can help me with it or can i put another apple id to it without putting the first password?THANKS FOR YOUR HELP.

Then call AppleCare and talk to someone in account security.

Share option for email does not work after Yosemite upgrade.

Hi,
Does anybody know why the share option, "Share via email" does not work anymore after Yosemite upgrade? I love this feature. It's just quick and easy.
Rod.

On Yosemite, Pages '09 v4.3 no longer recognizes the Share > Send Via Email categories. You will have to export and manually drag/drop/attach documents to Mail. There is no fix.

Security create-keychain does not add the keychain to search list

Hello guys,
It seems that since OS X Mavericks the security create-keychain does not add the keychain in the search list. I tried calling the SecKeychainCreate directly to verify that this is not a bug in the SecurityTool (the result is the same). Could you please help me verify if this is expected behavior or more like a bug that was not reported?
Is there other way to create a keychain and add it to the search list except modifying the whole search list (for ex. using the security list-keychain)? I would like to concurrently create more than one keychain and modifying the whole search list does not seem like a good practice, becuase it introduces a race condition.
P.S. I tested this in Yosemite and the behavior is the same.
Regards,
Ilian Iliev

Hi Carla,
Sorry to ask such a basic question, but are talking about Oracle Sales Analyzer?
Thanks,
Stuart Bunby
OLAP Blog: http://oracleOLAP.blogspot.com
OLAP Wiki: http://wiki.oracle.com/page/Oracle+OLAP+Option
OLAP on OTN: http://www.oracle.com/technology/products/bi/olap/index.html
DW on OTN : http://www.oracle.com/technology/products/bi/db/11g/index.html

Reply to email does not add previous address

Similar Messages

Maybe you are looking for