Report on WPA client level from WLC?

I'm transitioning clients from WPA to WPA2 and I want to make sure we've gotten most of them. Is there any way to run a report from the WLC to show encryption levels for clients?

Or better yet, create a new WLAN with the same SSID but different profile name. Have one configured for WPA/TKIP and the other for WPA2/AES. This way clients still on the old wpa SSID will appear as associated and you can then track them down.
Sent from Cisco Technical Support iPhone App

Similar Messages

Clients disconnected from WLC randomly

Hi,
I'm doing some tests with clients to see how much time they are kept registered in the controller while they are disconnected. I've set session timeout to 0 (infinite) and user idle timeout to 12 hours.
The problem is that sometimes the clients are disconnected from the controller before the user idle timeout expires:
apfMsDeleteByMscb Scheduling mobile for deletion with deleteReason 6, reasonCode 1
Other times they are expired normally by the user idle timeout (deleteReason4,reasonCode4).
If I am not wrong deleteReason 6 corresponds to manual deletion of the client, but there is no manual interventention when this happen, is the controller who deletes it.
Can anybody explain why this happens randomly?
WLC version 6.0.196
Thanks.

Refer the 2 Bugs :
Unified APs removing clients on maximum retries.
CSCti91944
Description
Symptom:
A wireless client might be removed from the mobility database before the user idle timeout. When this happens, if "debug client MAC" is in effect, messages similar to the following are seen on the WLC:
*spamApTask3: clientmacaddrXYZ Received Idle-Timeout from
AP macADDR-abc slot 0 for STA XYZ Client MAC ADDR
*spamApTask3: apfMsDeleteByMscb Scheduling mobile for deletion with
deleteReason 4, reasonCode 4
The symptoms, as experienced by the user, depends on the behavior of the client device and on the WLAN configuration as follows:
- If the WLAN is configured for web-auth, the client is forced to reauthenticate through the web.
- If the WLAN is configured for L3 mobility and if the client performs an L3 roam at the time of the removal, the client's old IP address in the old subnet is no longer valid, and the client is forced to re-DHCP in the new subnet. Any existing TCP connections fail to work expected. If the client is a 792x wireless phone on a call, the talk path is lost for the remainder of the call.
- If the WLAN is configured for L2 mobility, then the client is forced to perform a full EAP authentication (if EAP is configured) and to re-DHCP (if DHCP required is configured). In most cases, this does not cause a perceptible service interruption, unless the client's IP address changes.
Conditions:
This occurs when an access point fails to transmit 250 consecutive packets to the client (if there are 64 failed retransmits per packet, which means 4 consecutive dropped packets, it triggers the deauth).
Examples:
- Client radio is temporarily disabled.
- Client has gone into hibernation/standby.
- For a voice client, if the client is in a call and is unable to receive audio packets for a fraction of a second.
Workaround:
None; however, reconfiguring the WLAN for layer 2 rather than layer 3 mobility can mitigate the effect.
Known Affected Releases:
(3)
7.0(98.0)
6.0(199.0)
6.0(199.4)
Clients hit Idle timeout after successful authentication
CSCue34763
Description
Symptom:
A wireless client, while associated/authenticated (in RUN state), will be
prematurely idle timed out by an AP. With "debug client" in effect on the
WLC, messages similar to the following are seen:
*spamApTask2: Jan 30 17:10:17.258: 00:11:22:33:44:55 Received Idle-Timeout from
AP 84:78:ac:00:11:22, slot 1 for STA 00:11:22:33:44:558
*spamApTask2: Jan 30 17:10:17.258: 00:11:22:33:44:55 apfMsDeleteByMscb
Scheduling mobile for deletion with deleteReason 4, reasonCode 4
The idle timeout event occurs while the client is not idle, and more rapidly,
after the client's last reassociation, than the configured user idle timeout
value.
Conditions:
Flexconnect (H-REAP) local switching is configured, with DHCP Required.
Workaround:
Clients hit Idle timeout after successful authentication
CSCue34763
Description
Symptom:
A wireless client, while associated/authenticated (in RUN state), will be
prematurely idle timed out by an AP. With "debug client" in effect on the
WLC, messages similar to the following are seen:
*spamApTask2: Jan 30 17:10:17.258: 00:11:22:33:44:55 Received Idle-Timeout from
AP 84:78:ac:00:11:22, slot 1 for STA 00:11:22:33:44:558
*spamApTask2: Jan 30 17:10:17.258: 00:11:22:33:44:55 apfMsDeleteByMscb
Scheduling mobile for deletion with deleteReason 4, reasonCode 4
The idle timeout event occurs while the client is not idle, and more rapidly,
after the client's last reassociation, than the configured user idle timeout
value.
Conditions:
Flexconnect (H-REAP) local switching is configured, with DHCP Required.
Workaround:
Disable DHCP required.
Disable DHCP required.

Can Balance Sheet and P&L Statements be reported in Client Level?

Can BS and P&L Statements are reported under Chart Of Accounts Levelor they can be reported under Client( Group of one or more Chart Of Accounts) Level.

Hi,
If you have more than one company code operating in your client and all coampnaies are using same chart of account, then possibly you can generate B/S and P/L at client level. Other wise there is no reason to get conlsolideted financial statement per client level.
Kind Regards
Dinabandhu.

How Can We Change Batch Management Level From Client level to Plant Level?

Hi all,
I want to know whether it is possible to change the batch management level from client to plant level.Pls Help..

Hi,
Refer SAP Note 891902 - FAQ: Batch level

Help - Item Assignment at Inventory Organization level from the Interface

Hi,
I have developed an Inventory Item upload Interface (MTL_SYSTEM_ITEMS_INTERFACE Table) for Oracle Apps R12.
It works fine in uploading the Items to Master Org which the template is created. But When I tried to upload at Inventory Organization level it returns an error says 'Template or Template ID is not assigned for the Organization'.
How can I assign/upload the Item at Inventory Organization Level? I have already tried the Organization Item Assignment Report, It works fine and assign the Items to relevant Organizations. But the parameters are Item Range which I cant use those parameters.
Please help me to Upload items at Inventory Organization level from the Interface.
Thanks

open any delivery.
1. select any delivery item number( double click).
2. go to text tabstrip of the item.
3. select the text type and double click on the blank space where we write some texts will give you new screen for writing text will give you text screen.
then in menu: goto->header will popup screen with details given below.
text name: delv+item num
Language: 'EN'
text ID: '0001'       " for first text type and so on.
Text Object: 'VBBK'
****CODE.
data: ist_text type table of tline,
      wa_text type tline.
CALL FUNCTION 'READ_TEXT'
EXPORTING
   CLIENT                        = SY-MANDT
    id                            = 'textid'
    language                      = sy-langu
    name                          = 'textname'   " its concatenation of Dlv no. and item number.
    object                        = 'VBBP'
tables
    lines                         = ist_text
EXCEPTIONS
   ID                            = 1
   LANGUAGE                      = 2
   NAME                          = 3
   NOT_FOUND                     = 4
   OBJECT                        = 5
   REFERENCE_CHECK               = 6
   WRONG_ACCESS_TO_ARCHIVE       = 7
   OTHERS                        = 8
IF sy-subrc <> 0.
MESSAGE ID SY-MSGID TYPE SY-MSGTY NUMBER SY-MSGNO
        WITH SY-MSGV1 SY-MSGV2 SY-MSGV3 SY-MSGV4.
ENDIF.
Reward points if helpful.
Regards
Ashok

Changing Batch Management Level from Material to Plant

Hi all,
We are investigating changing our batch management level from material to plant to meet business requirements.
SAP has pointed us to a note with a program to reset the batch level, as well as highlighting some things to look out for.
I've conducted the change in a playpen system and so far it looks relatively straightforward, with complexities arising only when characteristics exist, or when a batch exists in multiple plants.
Seems that batch master data is moved from MCH1 to MCHA, including the object link number to classification. Unfortunately it seems a limitation of the conversion is that the batch master data is copied to ONE plant only in MCHA, no doubt due to the fact the object number link to classification must be unique.
My question is this: has anyone performed this change before, and if so can you offer me any advice on what to look out for, or potential problems that arose after the change?
Any help or comments are appreciated.
Mark.

hi..
first of all try this simple one...
You will have to delete all the materials, remove stock and then switch the batch management flag.
Or
To convert the batch from plant level to material there is Conversion Program defind by the SAP...
1. For all releases lower than Release 4.5B, implement the corrections and the modification in the report RM07CHDX as described in the correction instructions.
2. Create the report ZCHTCUCH, which is specified in the attachment.
3. Run this report in the clients for which you want to reset batch level to plant level.
4. Call transaction OMCT.
5. Check whether the batch level for "Batch unique at plant level" is set.
6. Implement Notes 821891, 944278, 950540 and 1091613 if you have not already done so (or you have not imported the corresponding Support Package).
7. Execute the function "Batch Level -> Conversion".
8. Define a plant for a plant view that may be missing.
9. Always execute the report in the test mode first. Analyze the error log.
10. If no errors occur, you can execute the report in production mode.
11. If you are working with batch long texts, first execute the report ZM07CHDX_TEXT in test mode.
try this out..hope is works,,
Thanks..

Client level , company code level , chart of account level

Hi experts
Pls expline me which are we define under client level , company code level and COA level
like :
1) field status variant:
2) Dunning procedure:
3) document types:
4) doc.number range:
4) posting periods variant
5) controlling area
6) account groups
7) vendor/cust master data
8) dep key
9) chart of dep area
10) like...............................
get points
Geeta

hi geeta,
ClientA Client is the highest unit within an SAP system and contains Master records and Tables. Data entered at this level are valid for all company code data and organizational structures allowing for data consistency. User access and authorizations are assigned to each client created. Users must specify which client they are working in at the point of logon to the SAP system.
A CompanyA Company is the unit to which your financial statements are created and can have one to many company codes assigned to it. A company is equivalent to your legal business organization. Consolidated financial statements are based on the companyu2019s financial statements. Companies are defined in configuration and assigned to company codes. Each company code must use the same COA( Chart of Accounts) and Fiscal Year. Also note that local currency for the company can be different.
Company CodesCompany Codes are the smallest unit within your organizational structure and is used for internal and external reporting purposes. Company Codes are not optional within SAP and are required to be defined. Financial transactions are viewed at the company code level. Company Codes can be created for any business organization whether national or international. It is recommended that once a Company Code has been defined in Configuration with all the required settings then other company codes later created should be copied from the existing company code. You can then make changes as needed. This reduces repetitive input of information that does not change from company code to company code as well as eliminate the possibility of missed data input.
Business Area Business Area is optional and is equivalent to a specific area of responsibility within your company or business segment. BA (Business Area) also allows for internal and external reporting.
Another configuration requirement for set-up in SAP are the Basic settings consisting of the following:
Chart of Accounts(COA)
Fiscal Year Variants.
Currencies
The COA(Chart of Accounts)
The COA(Chart of Accounts) lists all General Ledger accounts that are used by the organization. It is assigned in configuration to each company code and allows for daily General Ledger postings.
Fiscal Year configuration
Fiscal Year configuration is a must and can be defined to meet your companyu2019s reporting periods whether Fiscal (any period combination that is not calendar) or Calendar( Jan-Dec).
Posting Periods are defined and assigned to the Fiscal Year.
Within the periods you specify start dates and finished dates.
SAP allows for 12 posting periods along with specially defined periods that can be used for year-end financial closing.
Rohit Agrawal

Access point associated and deassociated from WLC

HI,
i have 3 AP AIR-LAP1042N-E-K9 in the same place (Event at down town) but they Sometimes the APs even disassociate from the controller temporarily, and i see the below errors on Prime infrastructure 2.0
Load threshold violation reported by 802.11b/g/n interface of AP <apname>, connected to controller <controllerIP>
Interference threshold violation reported by '802.11b/g/n' interface of AP
Coveraged threshold violation reported by 802.11b/g/n interface of AP <apname>, connected to controller <controllerIP>
what these problems and how to solve it
Thanks,
Ahmed

After these error done i see that error 802.11b/g/n interface of AP is down :controller.
please as example up time is 4:00 hours and join time changed every time may be once 12 m:15 sec, may be in another time 1h:15 m:20s
please feed me back these problem related to number of connected client because i monitor when the client exceed on AP more than 25 the AP deassociated from WLC. kindly find loggs from AP. wait your feed back.
*Mar 1 00:00:11.913: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed
*Mar 1 00:00:11.916: *** CRASH_LOG = YES
Security Core found.
Base Ethernet MAC address: 6C:20:56:48:E7:59
*Mar 1 00:00:13.876: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 0
*Mar 1 00:00:14.758: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot11Radio 1
*Mar 1 00:00:14.761: %LINK-6-UPDOWN: Interface GigabitEthernet0, changed state to up
*Mar 1 00:00:15.891: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet0, changed state to up
*Mar 1 00:00:18.795: %SYS-5-RESTART: System restarted --
Cisco IOS Software, C1040 Software (C1140-K9W8-M), Version 15.2(2)JB, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2012 by Cisco Systems, Inc.
Compiled Tue 11-Dec-12 04:03 by prod_rel_team
*Mar 1 00:00:18.796: %SNMP-5-COLDSTART: SNMP agent on host 90013-03 is undergoing a cold start
*Mar 1 00:00:18.868: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Mar 1 00:00:18.868: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
*Mar 1 00:00:19.865: %LINEPROTO-5-UPDOWN: Line protocol on Interface BVI1, changed state to up
*Mar 1 00:00:20.214: %SSH-5-ENABLED: SSH 2.0 has been enabledlwapp_crypto_init: MIC Present and Parsed Successfully
*Mar 1 00:00:46.958: Logging LWAPP message to 255.255.255.255.
*Mar 1 00:00:50.510: %CDP_PD-4-POWER_OK: Full power - NEGOTIATED inline power source
*Mar 1 00:00:51.533: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
*Mar 1 00:00:52.335: %DHCP-6-ADDRESS_ASSIGN: Interface BVI1 assigned DHCP address 10.35.49.35, mask 255.255.255.248, hostname 90013-03
*Mar 1 00:00:52.533: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Mar 1 00:00:52.559: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
*Mar 1 00:00:53.559: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
*Mar 1 00:01:03.221: %CAPWAP-3-ERRORLOG: Did not get log server settings from DHCP.
*Mar 1 00:01:13.236: %CAPWAP-3-ERRORLOG: Selected MWAR 'RMS-WLC1'(index 0).
*Mar 1 00:01:13.236: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Dec 9 09:54:50.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 10.94.70.2 peer_port: 5246
*Dec 9 09:54:50.919: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 10.94.70.2 peer_port: 5246
*Dec 9 09:54:50.920: %CAPWAP-5-SENDJOIN: sending Join Request to 10.94.70.2
*Dec 9 09:54:50.929: %CAPWAP-3-ERRORLOG: Invalid event 10 & state 5 combination.
*Dec 9 09:54:50.929: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 10 state 5.
*Dec 9 09:54:50.929: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
*Dec 9 09:54:50.930: %CAPWAP-3-ERRORLOG: Failed to process encrypted capwap packet from 10.94.70.2
*Dec 9 09:54:51.300: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to down
*Dec 9 09:54:51.355: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Dec 9 09:54:51.413: %CAPWAP-5-JOINEDCONTROLLER: AP has joined controller RMS-WLC1
*Dec 9 09:54:51.464: ac_first_hop_mac - IP:10.35.49.33 Hop IP:10.35.49.33 IDB:BVI1
*Dec 9 09:54:51.464: Setting AC first hop MAC: e804.62dc.9922
*Dec 9 09:54:51.464: ac_first_hop_mac - IP:10.35.49.33 Hop IP:10.35.49.33 IDB:BVI1
*Dec 9 09:54:51.464: Setting AC first hop MAC: e804.62dc.9922
*Dec 9 09:54:51.465: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
*Dec 9 09:54:51.595: %WIDS-6-ENABLED: IDS Signature is loaded and enabled
*Dec 9 09:54:52.300: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Dec 9 09:54:52.383: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to down
*Dec 9 09:54:52.388: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
*Dec 9 09:54:52.464: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to down
*Dec 9 09:54:53.377: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Dec 9 09:54:53.409: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
*Dec 9 09:54:53.416: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to down
*Dec 9 09:54:53.421: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to reset
*Dec 9 09:54:54.409: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio1, changed state to up
*Dec 9 09:54:54.416: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Dec 9 09:54:54.442: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
*Dec 9 09:54:55.443: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to up
*Dec 9 10:26:53.849: %WIDS-4-SIG_ALARM: Attack is detected on Sig:Standard Id:5 Channel:11 Source MAC:905f.2e62.e7a9
*Dec 9 10:32:20.938: %CAPWAP-3-ERRORLOG: Retransmission count for packet exceeded max(CAPWAP_WTP_EVENT_REQUEST
., 2)
*Dec 9 10:32:20.938: %CAPWAP-3-ERRORLOG: GOING BACK TO DISCOVER MODE
*Dec 9 10:32:20.938: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 10.94.70.2:5246
*Dec 9 10:32:20.994: %WIDS-6-DISABLED: IDS Signature is removed and disabled.
*Dec 9 10:32:20.997: %LWAPP-3-CLIENTERRORLOG: LWAPP LED Init: incorrect led state 255
*Dec 9 10:32:21.038: %LINK-5-CHANGED: Interface Dot11Radio0, changed state to administratively down
*Dec 9 10:32:21.039: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to administratively down
*Dec 9 10:32:21.041: %LINK-6-UPDOWN: Interface Dot11Radio0, changed state to up
*Dec 9 10:32:21.113: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to up
*Dec 9 10:32:19.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 10.94.69.2 peer_port: 5246
*Dec 9 10:32:19.925: %LINEPROTO-5-UPDOWN: Line protocol on Interface Dot11Radio0, changed state to down
*Dec 9 10:32:19.927: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 10.94.69.2 peer_port: 5246
*Dec 9 10:32:19.928: %CAPWAP-5-SENDJOIN: sending Join Request to 10.94.69.2
*Dec 9 10:32:19.939: %CAPWAP-3-ERRORLOG: Invalid event 10 & state 5 combination.
*Dec 9 10:32:19.939: %CAPWAP-3-ERRORLOG: CAPWAP SM handler: Failed to process message type 10 state 5.
*Dec 9 10:32:19.939: %CAPWAP-3-ERRORLOG: Failed to handle capwap control message from controller
*Dec 9 10:32:19.939: %CAPWAP-3-ERRORLOG: Failed to process encrypted capwap packet from 10.94.69.2
*Dec 9 10:32:20.093: %LINK-6-UPDOWN: Interface Dot11Radio1, changed state to down
*Dec 9 10:32:20.098: %LINK-5-CHANGED: Interface Dot11Radio1, changed state to reset
*Dec 9 10:32:20.370: %CAPWAP-5-JOINEDCONTROLLER: AP has joined controller UTO-WLC1
*Dec 9 10:32:20.424: ac_first_hop_mac - IP:10.35.49.33 Hop IP:10.35.49.33 IDB:BVI1
*Dec 9 10:32:20.424: Setting AC first hop MAC: e804.62dc.9922

Difference in client tables between WLC and AP controller d0

Hello gang,
Anyone know whether its normal to have an APs' d0/d1 controller output show clients that don't appear on the WLC's "sh client <AP>" output?
Here's an example - 10 clients visible from a "sh client " on the controller, but 15 clients visible on AP4s "sh controller d0" debug.
Granted the User Idle Timeout has been bumped up to 7200 seconds, but shouldn't the AP's d0/1 client table get updated if/when a client roams to another AP nonetheless? Wouldn't this otherwise cause confusion? Is the Split-MAC Split-brained?
Thanks for your input,
--Bruce Johnson
(mcores2wlc1) >show client ap 802.11b mell9s1ap4
MAC Address AP Id Status WLAN Id Authenticated
00:40:9d:31:b0:79 130 Associated 6 Yes
00:40:9d:34:1f:04 130 Associated 6 Yes
00:40:9d:33:ee:04 130 Associated 6 Yes
00:40:9d:2b:d1:6a 130 Associated 6 Yes
00:40:9d:31:23:a3 130 Associated 6 Yes
00:40:9d:33:e9:28 130 Associated 6 Yes
00:40:9d:31:27:a5 130 Associated 6 Yes
00:40:9d:33:eb:4b 130 Associated 6 Yes
00:40:9d:31:22:1d 130 Associated 6 Yes
00:40:9d:33:ee:cb 130 Associated 6 Yes
(mcores2wlc1) >debug ap command "sh cont d0" mell9s1ap4
(mcores2wlc1) >Thu Feb 26 18:54:10 2009: mell9s1ap4:
Thu Feb 26 18:54:10 2009: mell9s1ap4: ---Clients AID VLAN Status Age Tx Mode Enc Key Rate
Thu Feb 26 18:54:10 2009: mell9s1ap4: 0040.9d33.eaec 198 6 0000 0800000FF 7195/7200 0-0 10111 200 0-10 10000000 016
Thu Feb 26 18:54:10 2009: mell9s1ap4: 0040.9d30.efd1 197 6 0000 0800000FF 7195/7200 0-0 10111 200 0-10 10000000 016
Thu Feb 26 18:54:10 2009: mell9s1ap4: 0040.9d31.bc74 195 6 0000 2800001FF 7165/7200 0-0 10111 200 0-10 10000000 016
Thu Feb 26 18:54:10 2009: mell9s1ap4: 0040.9d31.27a5 193 6 0000 0800000FF 7195/7200 0-0 10111 200 0-10 10000000 016
Thu Feb 26 18:54:10 2009: mell9s1ap4: 0040.9d33.eecb 192 6 0000 2800000FF 7195/7200 0-0 10111 200 0-10 10000000 016
Thu Feb 26 18:54:10 2009: mell9s1ap4: 0040.9d31.221d 190 6 0000 0800000FF 7194/7200 0-0 10111 200 0-10 10000000 016
Thu Feb 26 18:54:10 2009: mell9s1ap4: 0040.9d33.eb4b 186 6 0000 0800000FF 7194/7200 0-0 10111 200 0-10 10000000 016
Thu Feb 26 18:54:10 2009: mell9s1ap4: 0016.6faf.9d64 185 3 0000 0C00000FF 7186/7200 0-0 0191 200 0-10 10FC0000 06C
Thu Feb 26 18:54:10 2009: mell9s1ap4: 0040.9d33.e928 177 6 0000 2800001FF 5818/7200 0-0 10111 200 0-10 10000000 016
=>Thu Feb 26 18:54:10 2009: mell9s1ap4: 0016.6faf.9db8 176 3 0000 0C00000FF 7140/7200 0-0 0191 200 0-10 10FC0000 06C
Thu Feb 26 18:54:10 2009: mell9s1ap4: 0040.9d31.23a3 174 6 0000 2800000FF 7195/7200 0-0 10111 200 0-10 10000000 016
Thu Feb 26 18:54:10 2009: mell9s1ap4: 0040.9d2b.d16a 165 6 0000 1800000FF 7194/7200 0-0 10111 200 0-10 10000000 016
Thu Feb 26 18:54:10 2009: mell9s1ap4: 0040.9d33.ee04 163 6 0000 0800000FF 7194/7200 0-0 10111 200 0-10 10000000 016
Thu Feb 26 18:54:10 2009: mell9s1ap4: 0040.9d34.1f04 151 6 0000 1800000FF 7195/7200 0-0 10111 200 0-10 10000000 016
Thu Feb 26 18:54:10 2009: mell9s1ap4: 0040.9d31.b079 147 6 0000 2800000FF 7194/7200 0-0 10111 200 0-10 10000000 016

hi Leo,
I tested this out, but i guess its not working as i thought it would work. I configured the backup primary controller IP and name in the global configuration of the Wireless tab of the WLC and left the AP high availability blank with no settings. I joined the AP to the WLC and show capwap client ha output on the AP shows the backup primary controller name. but if i shut down the primary controller, the AP does not join the back, it just tries to get WLC ip by renewing DHCP forever and stuck in that...   below are the outputs.. any idea why its like this ? I thot if there is no HA configured at the AP level, the global config on the controller level should take effect ?
LWAP3-1042#sh cap cli ha
fastHeartbeatTmr(sec)   7 (enabled)
primaryDiscoverTmr(sec) 30
primaryBackupWlcIp      0xA0A700A
primaryBackupWlcName    WLC2-4402-50
secondaryBackupWlcIp    0x0
secondaryBackupWlcName
DHCP renew try count    0
Fwd traffic stats get   0
Fast Heartbeat sent     0
Discovery attempt      0
Backup WLC array:
LWAP3-1042#
*Apr 30 20:36:21.324: %CAPWAP-3-DHCP_RENEW: Could not discover WLC using DHCP IP. Renewing DHCP IP.
Not in Bound state.
*Apr 30 20:36:31.829: %DHCP-6-ADDRESS_ASSIGN: Interface GigabitEthernet0 assigned DHCP address 10.10.114.49, mask 255.255.255.0, hostname LWAP3-1042
*Apr 30 20:37:17.832: %CAPWAP-3-DHCP_RENEW: Could not discover WLC using DHCP IP. Renewing DHCP IP.
Not in Bound state.
*Apr 30 20:37:28.337: %DHCP-6-ADDRESS_ASSIGN: Interface GigabitEthernet0 assigned DHCP address 10.10.114.50, mask 255.255.255.0, hostname LWAP3-1042
*Apr 30 20:38:14.338: %CAPWAP-3-DHCP_RENEW: Could not discover WLC using DHCP IP. Renewing DHCP IP.
Not in Bound state.
*Apr 30 20:38:24.842: %DHCP-6-ADDRESS_ASSIGN: Interface GigabitEthernet0 assigned DHCP address 10.10.114.51, mask 255.255.255.0, hostname LWAP3-1042
regards
Joe

Error while opening a report in FRstudio client machine.

Hi,I'm getting below error while opening a report in FRstudio client machine. please help me if any of you resolved this issue earlier.
client laptop: 64bit windows7
hyperion version: 11.1.2.2
error msg:
"HARSnapin Initialize() Error -2147467259 - ; nested exception is:
java.rmi.UnmarshalException: error unmarshalling return; nested exception is:
java.io.InvalidClassException: com.hyperion.reporting.graphics.GridObject; local class incompatible: stream classdesc serialVersionUID = 5432192847655595077, local class serialVersionUID = -5245705824007679661"
thanks

I've seen umarshalling error when there is a difference between the client and server version. Is there a patch applied? I would recommend to uninstall the existing one and install if from Workspace. (this will ensure that you've the correct client version)
Regards
Celvin
http://www.orahyplabs.com

View data in client B from client A in the same SID without a valid logon?

Hi Folks
We are planning on upgrading our 4.6C system to ERP 6.0, and are initialy considering having two clients in the same sandbox SID. One would be for the developers to perform code remediation checks (client A), and one would contain a copy of production data for performing testing of functionality over live data (client B).
Would it be possible to view data in client B from client A in the same system without a valid logon to client B or RFC connection to client B from client A? For example via the use on an ABAP program to SQL the database?
I know one can use transactions like SM30/SM31 to view, compare, and adjust data between clients, but this requires an RFC connection and valid logon to the target client.
Regards
Kevin.

Hi Kevin.
>
Kevin McLatchie wrote:
> Would it be possible to view data in client B from client A in the same system without a valid logon to client B or RFC connection to client B from client A? For example via the use on an ABAP program to
Short answer: yes.
If someone has the right to write and execute ABAP reports on the system he is able to access the data of all clients. So I don't think that this setup is advisable. Don't mix development and production data in one system.
Best regards,
Jan

WIS 10901 error while refreshing report in rich client

I'm facing a strange issue while refreshing a report from Rich client. Here are details
Environment: BO XI 3.1 SP3, Oracle application DB. Weu2019ve 2 BO servers (S1 and S2) on cluster and load balancer (common URL) in front.
While login to S1 with 6400 port, I can refresh report in rich client.
While login to S2 on 6400 port or using common url, during refresh gives below error u2013
u201CA database error occurred. Database error text is: (CS) u201CDBDriver failed to load: C:\Program Files\.....\dbd_oci.dllu201D (The specified procedure canu2019t be found) (WIS 10901)u201D
Iu2019ve installed oracle8i client on my system. Any idea what causing this issue?

Yes. Oracle 10g client installed on both application server. I've teste the universe connection from server, it's working fine.
Any idea what could be probable causes of "DBDriver failed to load: C:\Program Files\.....\dbd_oci.dllu201D error?
One observation, the path of dbd_oci.dll is the BO installation directory of my local machine (on server BO is not installed on C drive). Why it's referring dbd_oci.dll from local client even in 3 tier mode?

Bank details missing at Client Level

Hi,
We have created Vendor in R/3 system with Address and other detail including Bank details also.
But At the time of record checking at client level .
We are not getting the record releated to the Bank details .
Can any body in the forum put some light on this issue.
Thanks in Advance.
Regards
Rohit

Rohit,
I think that is the difference, Bank being a qualified table. In MDM you need to do load the tables individually. You need to extract the bank details from the R/3 separately and load in to the qualified table.
Then when you load the Vendor Master table and the Bank code you are assigning to the Venodr if it exists in the qualified table, you should be able to see it there.
Check out my blog
/people/ravikumar.allampallam/blog/2005/09/06/mdm-import-manager--get-data-for-check-tables
Hope this helps.
Regards,
Ravi
Note : Please reward points if this solves your issue.

If a material reports to two higher level assemblies in the BOM /Is there a

Hi,
If a material reports to two higher level assemblies in the BOM would creates two planned orders for it. Each of the orders has a different date?
For example
Z is final assembly
In that Y is one assembly in that says X1material in level 2
And the again same material X1 is reporting to Y in levels 5 so here my question is it would create two planned order with different dates?
And
Is there any report to see confirmed time to say machine time / labor time or shall we go for report.
Thx....Srini

Srini,
CS15 can be usefull to check the usage of component in assemblies.
if its used then more then once it can be easily located through this report.
another concern what you expressed is not clear.
But what i understand is same component is used at level 2 and level 4 of a BOM.
assumption from the word levels is , X is used in level 2 its used directly in BOM of Y and Y have some differnt component G which inturn again have X in it .
so at both this levels if the dependent requirement is different, you can get 2 differnet orders use individual /collective indicvator for this material as individual .
If your concern is for BOM position (Item Number) field in BOM then system will create a single plan order even if you set it for individual requirement in material master.here some work around can be possible by maintaining lead time offset IN BOM in item detail screen.
check and come back
Hope it helps you
Regards
Ritesh

Best practice: Developing report in Rich Client or InfoView?

Hi Experts,
I have a question on the best practice of developing webi reports.
From what I know, a Webi report can be created in Rich Client and then exported to one or more folders. From InfoView, the report can also be changed, but the change is only local to the folder.
To simplify development and maintenance, I believe both creation and change should be done solely in either Rich Client or InfoView. However, some features are only available in InfoView, not in Rich Client. One example is hyperlink for another Webi report. As a second step, I can add the extra features in InfoView after the export. However, if I change the report in Rich Client and re-export it, the extra features added via InfoView (e.g. report hyperlink) will be overwritten.
As I'm new to BO, may I have some recommendations on the best practice for building reports? For instance:
1) Only in Rich Client - no adding of feature via InfoView
2) First in Rich Client, then in InfoView - extra features need to be added again after each export
3) Only in InfoView - all activities done in InfoView, no development in Rich Client
4) Others?
Any advice is much appreciated.
Linda
Edited by: Linda on May 26, 2009 4:28 AM

Hi Ramaks, George and other experts,
Thanks a lot for your replies.
For my client, the developers will build most of the reports for regular users to view. However, some power users may also create their own reports to meet ad-hoc reporting requirements.
It's quite unlikely for my client to develop reports based on Excel or CSV data files. And we need to use features such as hyperlink for documents (which is not available in Rich Client). Based on these considerations, I'm thinking of doing all development in InfoView (both developers and power users). Do you foresee any issue if I go for this approach?
Thanks in advance.
Linda

Report on WPA client level from WLC?

Similar Messages

Maybe you are looking for