Reporting in WCS 6.0.132

I recently upgraded from WCS 5.2 to 6.0. I have a number of Client Count reports set up, which are run weekly to generate PDF graphs of usage on all APs in each building. Since the conversion, all of them fail with the message "Failed to run report". I've tried deleting and re-defining them, but get the same result. Running them manually makes no difference. Has anyone seen anything similar? Is there anything I can do, or is reporting just broken in 6.0? The message is singularly unhelpful
Regards
Max Caines
University of Wolverhampton

Have you used a beta version or earlier pre release version?
You have an issue that is related some how to entries that were in beta codes of WCS.
A few things to try, first make a backup of your db.
Then, go on the CLI, bin folder of WCS and after run:
1.StopWCS
2.dbamin checkschema
3.StartWCS
See if this helps.
I dont want to push you for opening a TAC case and would like to avoid it, but if you are concerned about keeping the same db and not loose any data, we need a TAC case to be opened. That will involve that you upload me your database so we can try to fix this manually.
If you dont care about the DB and you are ok to rebuild it then from the CLI
1. StopWCS
2. dbadmin reinitdb
3. StartWCS
Reconfigure your WCS, the issue will be gone.
If you decide that you can not loose the db and the previous steps did not help, open a TAC SR between now and the next couple of hours and ask for lavramov, I can help you out.

Similar Messages

  • Can't add Controller over VPN in WCS v6.0.132.0

    Hi
    I use WCS v6.0.132.0 to manage my 4402 and 2106 controller both running version 6.0.182.0
    When I try to add another 2106 over DM-VPN it fails with the following errors:
    ”No response from device, check SNMP communities, version or network for issues”
    If I move the new 2106 controller to LAN with same config there is no problem.
    I found this note in the in “Cisco Wireless Control System Configuration Guide, Release 6.0”
    “Note If you are adding a controller into WCS across a GRE link using IPsec or a lower MTU link with multiple fragments, you may need to adjust the MaxVar Binds PerPDU. If it is set too high, the controller may fail to be added into WCS. To adjust the MaxVarBindsPerPDU setting, do the following:
    1) Stop WCS.
    2) Go to the location of the Open SnmpParameters.properties file on the server that is running WCS.
    3) Edit MaxVarBindsPerPDU to 50 or lower.
    4) Restart WCS.”
    On my system I have the “SnmpParameters.properties” file is located //WCS6.0.132.0\webnms\classes\com\cisco\server\resources
    But I don’t have “MaxVarBindsPerPDU” settings in the file.
    Beside some # explanations text, the only settings I have in the “SnmpParameters.properties” file is:
    DebugEnabled                         false
    SerializeRequests                    true
    MaxRepetitions                       10
    MaxRetryTimeout                      60
    WlanTimeoutMsecsPerAP                 50
    I have tried to add “MaxVarBindsPerPDU” settings, but it have no effect.
    Anyone have an idea what to do?
    TIA

    Thank you so much! 
    Step 1 solved the issue.
    I changed “Maximum VarBinds per Get PDU” from 30 to 20 and “Maximum VarBinds per Set PDU” from 50 to 20.
    Thanks

  • Reporting in WCS Question

    Is there any way to generate report in WCS for clients associated / authenticated by AP's. I was able to get Client count by controller, What I need is client count by Access Point.
    If anyone has any suggestions please contribute. WCS Version 7.0.172.0
    Thanks
    Anil Jacob

    Have you used a beta version or earlier pre release version?
    You have an issue that is related some how to entries that were in beta codes of WCS.
    A few things to try, first make a backup of your db.
    Then, go on the CLI, bin folder of WCS and after run:
    1.StopWCS
    2.dbamin checkschema
    3.StartWCS
    See if this helps.
    I dont want to push you for opening a TAC case and would like to avoid it, but if you are concerned about keeping the same db and not loose any data, we need a TAC case to be opened. That will involve that you upload me your database so we can try to fix this manually.
    If you dont care about the DB and you are ok to rebuild it then from the CLI
    1. StopWCS
    2. dbadmin reinitdb
    3. StartWCS
    Reconfigure your WCS, the issue will be gone.
    If you decide that you can not loose the db and the previous steps did not help, open a TAC SR between now and the next couple of hours and ask for lavramov, I can help you out.

  • WLC 5.2.193.0 with WCS 6.0.132.0 a supported config?

    I know of a large site (not one of mine) that is running WLC 5.2.193.0 code paired up with WCS 6.0.132.0. The release notes for each product make no mention of support for this configuration.
    Is this is supported configuration?

    Thanks to both of you who replied. I just need to ensure that Cisco will support this scenario. The larger site is actually a "parent" site, and we try to keep our configs in parallel, but I'm not going to put the smaller site into an unsupported configuration.
    I found this document, updated September 1st, which still doesn't list WLC 5.2.193.0 and WCS 6.0.132.0 as a supported config:
    http://www.cisco.com/en/US/products/ps6366/products_tech_note09186a0080af7140.shtml

  • WCS 6.0.132.0 Error

    Hi,
    I have a problem with WCS 6.0.132.0.
    I get every time I press a link a popup with error: "System Error: Wrong Alarm Type rogueUnclassifiedMinor"
    Is this a bug?
    Any idea to solve this?
    Thanks in advance

    Hi Juan,
    This bug was supposed to be fixed, but it looks like it may have crept back in 6.x;
    CSCsr02317 Bug Details
    Getting error message for alarm dashboard after upgrade from D3MR2 to F
    Symptom:
    Receive error popup constantly that states the following:
    System Error: Wrong Alarm Type rogueUnclassifiedMinor
    Conditions:
    After upgrading the WCS this happens
    Workaround:
    Clear the browser cache and cookies. Then restart browser and the error message should go away. Status
    Fixed
    Severity
    4 - minor
    Last Modified
    In Last Year
    Product
    Cisco Wireless Control System
    Technology
    1st Found-In
    5.1(63.0)
    5.1(65.4)
    Fixed-In
    5.2(44.0)
    Hope this helps!
    Rob

  • Reporting MSE (WCS)

    Hi@all,
    we have a small problem with the "Client Location Tracking"-report in WCS.
    If we make create a job for this kind and activate the schedule, we get empty reports. If we open the job and press "run", we get all clients listed. (eport is possible, too).
    If the job is running via the schedule, we get "Report ran successfully and the run result has no data" but this is impossible.
    Our infrastructure:
      MSE 3355 (7.0.240)
      WCS     (7.0.240)
       WLC 4404 (7.0.240).
    I hope anybody could help.
    kind regards
      René

    So, yesterday we cleared the database of the MSE via WCS.
    After this procedure we got our reports.
    Now, round about 24h later, they are corrupt.
    If we look at the CPU-Status of the MSE, we see that some oracle -instances have 100%CPU (also 1 core full) and a report takes ~ 10 Minutes.
    If execute the report now, we get it in 20-30 sec.
    Also it seems a bug. TAC case is opened, but it looks like that we don´t get help, missing contract *argh*
    Edit:
    What i have been realized, that the DB disk memory is 4199696000. It seems, that the db, couldn´t be larger than 4GB, because yesterday we have nearly the same amount of data befoor we cleaned the database. This couldn´t be correct, or?

  • WCS 6.0.132.0 Database

    Hello,
    I've been having some problems with the linux version of WCS. Sometimes, and I still don't know why the Database server stops. To activate it again I need to restart the service using the WCSStart script. Is anyone having similar problems? The service can work for two weeks or a month... then it just stops.
    Best regards

    Hello,
    my database stoped working again... It happened last night.
    I got this output from the WCSStatus script.
    "Health Monitor is running.
    WCS is initialized, but is not serving web pages.
    The Server seems to be unavailable. The possible reasons are
    1. The server is not running yet.
    2. The server is hanging.
    3 The server has crashed.
    If the server has crashed or is hanging
    Please report the issue and follow the instructions to restart it.
    1. Run StopWCS to stop all WCS processes.
    2. Run StartWCS to start the WCS server.
    3. If the server still fails to start, or you still get this
    message, then reboot the machine.
    Database server is stopped
    Apache server is running"
    So I think the DBAdmin didn't solve the problem. Any next steps?
    Thanks for your help.
    Tiago

  • Detailed client Report in WCS

    Hi,
    what exactly mean the fields of the traps  that appear in the Detailed Client report of the WCS?
    07/08/10 08:09,"00:04:23:71:67:bf",,"Campus> Ome > CN.OM.P03","XSFK2MP345","10.120.205.25",07/08/10 08:09,"0 secs","0.0.0.0",0,-128,"802.11b","N/A",0,0,0,0,"No","Associated","Client '00:04:23:71:67:bf' is associated with AP '00:23:eb:2d:8a:e0', interface '0'."
    which means many  associations of  "0Sec" with no IP assigned?
    Thanks!

    Hi,
    Are you still facing this issue?
    thanks,
    Vinay

  • WCS 6.0.132 compatibility

    Is this version of WCS compatible with a Controller using 5.2.193? I've checked the released notes and for Controller 5.2.193 it says it needs WCS 5.2.130, but is 6.0.132 WCS also compatible?
    Thanks in advance!

    Yes 6.0.132.0 is compatible with controller 5.2.193.0

  • Interpretations of 802.11 counters report on WCS

    Dear Sir,
    My customer recently deployed WLCs and WCS in their environment. However, recently they experienced slow performance. To futher finding out the root cause, I generated the 802.11 counters report from the WCS and noticed the following parameters is shown.
    Tx/Rx Fragment Count/Sec and FCS Error Count/Sec
    1. Can I make the assumptions that the overall transfer of packet rate in that interval is the Total of Tx/Rx Fragment Count/Sec and FCS Error Count/Sec?
    2. If the output rate of Tx/Rx Fragment Count/Sec and FCS Error Count/Sec are the same, does it mean that 50% of the packet are corrupted and this high FCA Error Count/Sec will cause performance degradation to the wireless througphput?
    3. What is the baseline of the FCS Error Count/Sec that is acceptable? As for the case with wired, 1% error rate is acceptable. Will wireless have the same baseline?
    Thanks
    -delon

    FCS error count is the number of frames that were transmitted/received with a bad checksum (CRC value) in the ethernet frame. These frames are dropped and not propagated onto other ports. Usually we check FCS errors at the asic level so they never even hit the backplane. Few of these errors are OK, but could also be an indication of bad cables, NICs,etc.
    Catalyst keeps track of Tranmit FCS and Receive FCS. The Receive FCS is normal since its coming from the cable, Transmit FCS errors, however, should not occur and are an indication of bad hardware in the Catalyst. The FCS counter is a sum of Tx and Rx FCS errors.

  • Generation of Client summary report on WCS

    Hi,
    I have four WLCs running the IOS  version 7.0 at different locations. All these WLCs are joined to the WCS at one location.
    I am trying to generate the client summary report. But i am not able to generate the report as per the requirements.
    Please let me know is it possible to generate the client summary report for each controller.(i.e) The report providing the details of the users at each location. If so, Please let me know the procedure.

    Hi,
    Client summary cannot be narrowed down to Controller ip.. However, the "Client session report" will help you out in getting the report per Controller and this gives the client TX, RX and you can custpmize it as well!!
    here is the link to do it..
    http://www.cisco.com/en/US/docs/wireless/wcs/7.0/configuration/guide/7_0reps.html#wp1135765
    lemme know if this answered ur question!!
    Regards
    Surendra

  • MFP Error reported in WCS

    I've searched for the following errors but cant find anything on the MFP Invalid Sequence Number error
    I have just enabled Management Frame Protection (MFP) under AP Authentication / Wireless Protection Ploicies.  Since then I have seen the follwoing MFP related errors on WCS.
    MFP Anomaly Detected - 11 'Invalid Sequence Number' violation(s) have  originated from the AP with BSS '00:11:20:8e:91:50'.  This was detected  by the radio with Slot ID '0' of the AP with MAC '00:1a:e3:76:fd:50'  when observing 'Deauthentication' frames.
    MFP Anomaly Detected - 20 'No MIC' violation(s) have originated from the  AP with BSS '00:26:cb:ac:7e:71'.  This was detected by the radio with  Slot ID '0' of the AP with MAC '00:26:cb:d1:b2:b0' when observing  'Deauthentication' frames.
    The WLC's are running 6.0.196.0 and WCS is on 6.0.170.0.
    My question is what do these errors refer toand how do I get rid of them??  What caveats are there for impleementing this globally or on a per WLAN basis?
    Any ideas?
    Thanks
    Martin

    Hello,
    I have exact the same error message 8 or 10 times per days, but we have MFP enabled on our system from long time and we have WLC Version 7.0.98.0 and WCS 7.0.164.0.
    Did you get solutions for that?
    Thanks for your help

  • Rogue reporting in WCS

    Can anybody tell me what the difference is between the following 2 default Security reports:
    Rogue APs
    Rouge APs Event
    WE run both of these nightly, but the Rogue APs Event report usually is about 20 pages or so, and the information there has way more than what I see when I compare to my controller. The Rogue APs report usually matches what I see on my controller regarding current rogues. Does the Rogue APs Event report just detail everything that the access points have seen in the reporting time period? Some clarification on this would be greatly appreciated.
    Thank you.

    Rogues Detected by APs Report displays information about specific rogue access points detected on the network, rather than having to look into each rogue alarm and manually assemble a list. The data that is returned includes but is not limited to the following: the name of the detecting access point, the MAC address of the rogue, and the location of the rogue.
    and Security Summary Report shows the number of association failures, rogues access points, ad hocs, and access point connections or disconnections over one month.

  • Can't Modify WCS Report File Destination

    Once I upgraded to WCS 6.0.132.0 I can no longer change the destination file location when I run reports. The reports seem to run on schedule but they end up in the default location of C:\WCSFTP\reports\. I would like to change that to my E: where I have more space to save reports. Before version 6.0.132.0 I was able to do this.

    Oops, I sent the wrong screenshot.
    Go to administration -> settings and you can change the folder there.
    You can not customize the file name but surely you can change the location to save the files.
    See file attached.

  • Reporting problems with Cisco WCS

    hi all,
    I was wondering whether anyone has experienced the following symptoms on Reporting.
    WCS Rogue AP reports do not run and show up as 'Expired'
    this does not occur to all the Rouge AP  reports though (they are being created based on floor areas; one report per campus)
    customer is using the following
    WCS Version: 7.0.230.0
    any idea on this, could this be a software bug?
    thanks a lot
    with kind regards,
    Lancellot

    Hi,
    The report expires when it is scheduled report and configured for some specific time. After the time passed the report expires. re-schedule the report time and change the start-date time of the schedule and that should resolve your issue.
    HTH
    Amjad
    Rating useful replies is more useful than saying "Thank you"

Maybe you are looking for

  • Blocking Vendor Payment Using F110

    Hi All, If I run F110 to pay a vendor, block one of the open items for payment, carry out the payment run, and start another payment run for the same vendor, will the open item that was blocked still be blocked? Will I have to unblock it? Thanks, Dek

  • Not able to get the Alias Name(Member Description) in FR by using Planning

    Hi All, we are using the 11.1.2 version in my project. While i am developing the FR repots by using planning database i am not able to find the Member name in my report, but i am able to see the option. MemberName, Alias and Both. If i check the Alia

  • How can I make NETRIS listings work on Firefox.

    I have always kept NETRIS on Internet E because it will not work on Firefox. Some of the buttons will not work. A tech guys said yesterday that it now works and to ditch internet E because it causes problems. But I still cannot get the search etc. bu

  • Problem In Session State

    Hai, I'm Using VS2010 and SQL Server 2005. I have a problem in Session state; //View.aspx.cs // In this page just I store a textbox into a session variable. protected void btnEdit_Click(object sender, EventArgs e)         Session["rollno"] = txtRollN

  • Servlet - Multithreaded unique object confusion.

    Hye there experts. A Servlet is a multi-threaded unique object - no doubt about this. My question is straight, that I am trying to understand When a variable is created inside any unique multi threaded object (like Servlet), and when it serves number