Reports in Cisco Prime

Hi,
I have installed the LMS 4.1 in our network. I would like to generate an Interface_Utilization Report for all the interfaces of the device group I already chose, not just the "Top/Bottom 10", is there anyway to carry out this?
Thanks in advanced.
Best regards,
Laura Herrero

Hi
You can get this from an inventory report in PI (Select Report Type AP). Here is an example of PI 2.1 works for me. Once you export this into excel you can sort based on controllers & filter the single controller connected AP you want.
Regards
Rasika
**** Pls rate all useful responses ****

Similar Messages

How can I get CDP neighbor information from access point reports in Cisco Prime 2.0

How can I get CDP neighbor information from access point reports in Cisco Prime 2.0? I have looked through all the reports and I cannot find a report that gives me the CDP neighbor information of an access point. I thought that information was in there, however I cannot seem to find it.
Thanks in advance!

Hi
You can get this from an inventory report in PI (Select Report Type AP). Here is an example of PI 2.1 works for me. Once you export this into excel you can sort based on controllers & filter the single controller connected AP you want.
Regards
Rasika
**** Pls rate all useful responses ****

Customized report on Cisco Prime 2.0

Hi to all,
I'm searching for a customized report on the Cisco PI 2.0. I'd like to have a report showing an inventory of my APs wit their ethernet mac, radio mac, IP, serial number. I did have a look at the 'device' part available on the Report launchpad but cannot find what I want.
Do you know where I can find this kind of report? Or any way to choose the columns I want?
Thanks!
Theo

HI,
YEs you can do it via PI.
GO to Report launch pad >Device > Inventory then click on New
Screenshot:
Then clcik on Customize.
Hope it helps.
Regards
Dont forget rate helpful posts

CISCO PRIME INFRASTRUCTURE NETFLOW TRAFFIC REPORT

Hi,
I have a report from cisco prime infrastructure, that I don´t know how to interpret, because the fields in the report I don´t know what´s mean them, the difference between them, what are optimal values, the worse values, etc.
Can someone help me with this
The name of the report is: FLEX NETFLOW TRAFFIC TQPQ
The fields that I don´t know what are:

hello,
I also have a problem concerning the interpretation of the report that I got. if anyone knows how Cisco gets its premium reports, it will help me!

Cisco Prime Infrastructure - Is there a report of unused switch ports?

Hello,
Is there a report in Cisco Prime Infrastructure 1.4 showing the unused switch ports?
There used to be one in Cisco Prime LMS (Reclaim Unused Up/Down Ports Report).
Thank you,
Luke

Hello,
I now have Cisco Prime Infrastructure 2.0 running, and I don't see a report like the "Reclaim Unused Up/Down Ports" report that existed in LMS.
I found one called "Interface Capacity", but it only shows the number of ports that are "connected", "notconnect" or "disabled".
Does anyone know if a report of Unused ports exists in Prime Infrastructure 2.0 or if it will be available later on?
Thank you,
Luke

Cisco Prime Infrastructure 2.1 Custom Reports

Hi, I need to generate a custom Guest User report from Cisco Prime Infrastructure 2.1. It needs to have a couple more fields added to the existing "Guest User Association" report.
Is it possible to connect to the Cisco Prime Infrastructure Database and Generate custom reports? Is there any documentation on this?
Thanks

Programmatic access to PI's data is via the REST API.
Check the help menu on your PI server to see documentation regarding the supported tables and fields that can be queried via that method.

Cisco Prime: Event Larm Port 'x' is down on device.

Hi,
I'm writing regarding; event-larms; that is reporting from Cisco Prime; connected to controller. Interfaces is reporting via event-larm; that they are down.
"Virtual Domain: ROOT-DOMAIN
PI has detected a change in one or more alarms of category Controller and severity Critical in Virtual Domain ROOT-DOMAIN.
The new severity of the following items is Clear:
1. Message: Port '3' is down on device '10.1.1.2'.
(6 times)
2. Message: Port '4' is down on device '10.1.1.2'.
(6 times)
3. Message: Port '5' is down on device '10.1.1.2'.
(6 times)
4. Message: Port '6' is down on device '10.1.1.2'.
(6 times)
5. Message: Port '7' is down on device '10.1.1.2'.
(6 times)
6. Message: Port '8' is down on device '10.1.1.2'.
(6 times)
E-mail will be suppressed up to 30 minutes for these changes."
Is there a solution how to not recieve those event-larms? The only LACP interfaces that is configured is 1 & 2, in a group.
See attached screenshot, when trying to disable the other interfaces.
The LACP is enabled and configured on "management" interface.
Best Regards,
David

From: https://supportforums.cisco.com/discussion/12077376/prime-infrastructure-alarm-port-down#comment-9405836
"As far as I understand the error message you only need to disable SSO before you can disable the LAG ports."
"(Cisco Controller) >config port adminmode 3 disable
Blocked: Lag is enabled. Disabling the lag port is blocked when system is in redundancy state (SSO)"
"I would suggest to do this only in a maintenance window."

Cisco Prime Rogue AP Report - No Rogues from 3702 Series AP's

I am running Cisco Prime Infrastructure (2.1) that manages a Cisco 5508 WLC (7.6). We have multiple version of AP's managed by this WLC to include 1142, 2602, 3702, etc...In Cisco prime when we run a Rogue AP Report. None of the Rogue AP's discovered by 3702's are displayed in the report. The Rogues show on the WLC though from all AP's. Cannot find a reason for this. Any ideas?

The Rogue alarm state always stays on "removed" once deleted
CSCuo91446
Description
Symptom:
Once one of the alarm of rogue AP is deleted the newer rogue AP alarm changed to removed state even for different mac address.
Because of the removed state the detecting AP which detected the rogue is not displayed
Conditions:
1) Auto SPT is turned on
2) Prime 2.0 or 2.1
Workaround:
Click on refresh from network for each alarm in removed state or disable auto spt
Last Modified:
Jun 30,2014
Status:
Fixed
Severity:
3 Moderate
Product:
Cisco Prime Network Control System Series Appliances
Known Affected Releases:
(1)
2.1(0.0.1)

Cisco Prime Collaboration Assurance IPPhone 3901 no serial number report

Hi All,
I have installed Cisco Prime Collaboration Assurance in my office and try to create phone inventory report , so far no problem , but when i add IPPhone 3901 there no serial number in the report , I have enable web access on the phone , i can see the serial number by click the IP .
any help ?
Best Regards,
Tommy

Cisco Prime Infrastructure 2.1 Not generating reports

Dears,
I am new to Cisco Prime. I installed Cisco Prime Infrastructure 2.1 for 60-days evaluation and i added routers, switches and APs. I configured SNMP community and telnet credentials. I can see clients on Dashboard, but when i go to reports and generate them for last hour, it displays "None Detected".
Please advise.

Programmatic access to PI's data is via the REST API.
Check the help menu on your PI server to see documentation regarding the supported tables and fields that can be queried via that method.

"Busiest Clients" report template on Cisco Prime & Aironet 1242AG

Yesterday I was trying to schedule a "Busiest Clients" report on our Cisco Prime physical appliance (PRIME-NCS-APL-K9, v2.1.0.0.87).
My goal was to monitor the busiest clients on a couple of old Aironet access-points. These APs have been installed in a branch office of our university that rely on 4 Mb/s SHDSL WAN connectivity and, as you might imagine, some saturation occurs when the classrooms are crowded.
Unfortunately, all the reports were empty ... there was only a "No data matches the specified criteria for the report” warning inside.
The Client Statistics task (Administration>Background Tasks) was enabled and I was able to run this report selecting a different floor area ... after a few tries I've discovered that this error occurs only when the old Aironet 1242AG APs are involved. If I select a floor area populated with the newer 1142 and 2602 models, the report template works as intended.
So, is there a way to fill a "Busiest Clients" report with data fetched from our old Aironet 1242AG APs?
Our WLC is a Cisco Wireless Services Module 2 Controller for Cisco Catalyst 6500 (WS-SVC-WISM2-K9).
(Sorry ... my English is a bit rusty)

Hi,
Kindly try to restart the Dameon manager with the command line of the server
1> net stop crmdmgtd
and then start the daemon manager --> net start crmdmgtd (wait for atleast 20-25 minutes before login back to LMS and also see if any file do exist at location CSCOps\Objects\dmgtd\ready folder).
Get the output of pdshow after waiting for 20 minutes and stdout.log and stderr.log from CSCOpx\MDC\tomcat\logs.
Many Thanks,
Gaganjeet

Cisco Prime - Custom Inventory Change Report?

Hi,
Cisco Prime has this report:
Reports > Inventory > 24-hour Inventory Change
The problem is that the Report reports things that I don't want to track, like changes in "NVRAM Used", Interface Speed, etc...
Is it possible to configure Inventory Change so that it would not check some itens?
Thanks.

Thanks for answering,
my report has, for example, the following information:
Changes for Device: router01
Processor Identity: ProcessorID = 3
Attribute Type of Change Time Change Detected Previous Value Current Value
NVRAM Used (KB) Changed 2014-02-21 00:10:00.69 16923 16953
I saw that Syslog Automated Actions > Inventory Fetch has very useful configuratios, but I think that it is still not what I need. The screen you pointed out was related to messages from Syslog that triggers inventory collection.
What I need is in the image below.
All right, NVRAM changed it's current used size. For me, it is completely useless to know about that every day in my Inventory Change report. That information is flooding my report. How to remove it from future reports?
Thanks again!
Message was edited by: Leonardo Machado

Cisco Prime -report

I have installed Cisco prime infrastructure 2.2 and configured it.
Now i want Per switch Per vlan traffic and per switch per vlan session
for that what i have to do please suggest me as soon as possible
Switches is 2960 and 3750X.
Please suggest me and i want that report also..

Your layer 2 switches won't give you much of anything as far as traffic per VLAN as they do not have any interface to report against. The router (or layer 3 switch) which is the gateway for your VLANs can be queried to show the traffic for the Layer 3 Switch Virtual Interface (SVI). That shows up like any other interface in the performance reports.
I'm not sure what you mean by "per vlan session". Can you explain (preferably with an example of how you would do that from command line)?

Can Cisco Prime send a peer to peer connectivity report

I'm trying to discover if we have any peer to peer wireless clients (not ad-hoc WLANs) talking to each other. I was asked to turn off peer to peer on the wireless network, so I need to find out if there are any clients talking to one another, and if so, what are they, etc.
I've looked through the reports and didn't see anything there.
We have Cisco Prime 7.2, 5508 WLCs and MSE.

Please check the below link:
http://www.cisco.com/en/US/docs/net_mgmt/ciscoworks_lan_management_solution/4.2/user/guide/reports/system_reports.html

Cisco Prime Infrastructure 1.3 - reports

Hi all,
I am curious if anybody can help me with Cisco Prime reports. What I want to do is to create report of all my devices which will have information such as hostname, IP adress, . . . , an serial number. I found this task almost inpossible... When I look at the device work center tab and click on one of my devices I can see alll of the information I want (so good so far all infromation are available..but..)When I want to create such a report from all of devices in report section I pick up Detail Device Inventory and customize report which I want. Problem appears after report is done. The main ifnormation such as hostname, location an IP adress are in the first part of report and in the second part there are chassis information with serial number and other fields. But these two parts of report dont have any common field so it is impossible for me to match serial number to hostname..So if I dont want to click on every device in device work center and write down all of information I dont know how to do such a simple task...
I hope someone is able to follow my thoughts
Thanks for any answer
Martin

Robert-
If you create a separate service rule, you can have it fork TACACS authentication requests from that specific IP to a different Service identity and authorization process, where you can tell it to select a specific shell profile. Then all you have to do is create a separate shell profile for managing Prime and have that one selected. We do this with our UCS dvices, regular router/switch CLI logins, etc.
So for example:
UCS: TACACS request --> if match service selection rule "from UCS devices", go to UCS admin access policy --> if match ucs admin identiy reqirements, give UCS admin shell profile
PI: TACACS request --> if match service selection rule "from PI devices", go to PI admin access policy --> if match PI admin identiy reqirements (which are same as UCS), give PI admin shell profile
Default: TACACS request --> if match tacacs protocol from our IP range, go to default device admin policy --> if match defaul identy requirements, give default admin shell profile

Reports in Cisco Prime

Similar Messages

Maybe you are looking for